PROVN OF CERTAIN LBW SPECIAL REPAIR AND MINOR WORKS AT AGE BR I AND II UNDER GE NORTH BIKANER AT MIL STATION BIKANER ESTIMATED COST Rs 39.40 LAKHS AND CERTAIN MINOR WORKS SEWAGE DISPOSAL PIPE LINE AT ASCON NODE AMARPURA ESTIMATED COST Rs 4.84 LAKHS

Amount

Dismantling of Roof tiles of any description or thickness in floor, roof, apron etc laid, bedded and pointed in any mortar complete.

Demolition of lime concrete of any description over roof slab complete all as specified by Engineer-in-Charge.

M & L for 10 mm thick screeding in cement mortar 1:6 on concrete surfaces, finished fair & even including mixing water proofing compound as per manufacturer's instructions complete. (WPC shall be measured separately as supply only) all as specified.

Supply only liquid water proofing compound ISI Mark complete. Make: Dr. Fixit or Equivalent.

M&L applying priming coat of cold bitumen primer at the rate of 0.40 Ltrs per Sqm as per para 11.44.5 of MES SSR Part-I incl cleaning and preparing the surface complete all as specified.

M & L APP based polymeric membrane minimum weighing 3 kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. Not less than 150 gms/sqm) land on primed surfaces by forced application complete all as specified.

M & L for lime concrete terracing as on roof with mimimum thickness of edge 40 mm and increasing uniformly towards ridge to obtain a certain chain slope of (1:40) as described in para 11.27.2 of MES SSR part-I complete all as specified. NOTE:- For lime concrete, mudia kankar (source : NAL) and Kolayat coarse sand in lieu of brick aggregates and Surkhi respectively as specified in MES schedule Part-I shall be used.

M & L for 40 mm thick brunt clay brick tiles bedded on cement mortar and joints grouted flush in cement and sand mortar (1:3) mixed with integral water proofing compound IS 2645 : 2003 @ 3% by wt of cement as Complete all as specified and as directed..

ditto complete all as per Item No 8 above but except tiles complete all as specified.

Dismantling floor, hearth or wall tiling any type including cement mortar bedding but not backing, removing serviceable tiles to store and rubbish off the primises Complete.

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified.

M & L for coloured Non skid ceramic tiles 7 to 8 mm thick (squar/ rectangular) area of each tiles exc 0.11 Sqm but n.exc 0.18 Sqm in floor etc. set and jointed in neat cement slurry and pointed in coloured cement to match the floor laid over 15mm thick screed bed in cement mortar 1:6 complete all as specified.

M & L for coloured Glazed ceramic tiles 450mm x 350mm x 7mm or 300mm x 450mm x 7mm thick set and jointed in neat cement slurry and pointed in coloured cement to match the floor as on vertical surfaces laid over 10 mm thick cement plaster in 1:4 complete all as specified.

M & L for 25 mm thick Cement concrete 1:2:4 type B0 using 12.5mm graded stone aggregate in floors to receive finished even and smooth using extra cement complete all as specified.

Demolition of reinforcement concrete of any description and in any position not otherwise specifically provided for concrete complete all as specified and directed.

M & L for M-25 (Design mix) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified.

M & L for Mild steel TMT bars 10mm dia and over as reinforcement for concrete, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M & L for 20 mm thick granite (of any tpe) work (table rubbed and polished) in steps, jambs, pillars, windowcills,cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified.

Rounding to edges of stone slabs one edges such as in steps, cooking platform and other similar situations complete all as specified.

Taking down chowkhats or frames not exc. 1.50 Sqm each but with shutter (with out taking of shutter from the frame ) and making good the surface of walls as per existing with cement mortar complete.

M & L for PCC 1:3:6 type C-1 (using 20mm Graded Stone Aggregate) as in fixing Holdfast, Plinth courses, bed plates, string courses, coping, filling of chowkhats etc., complete all as specified and as directed by Engr-in-Charge.

M&L Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube all as specified and approved.

M&L factory made solid panel PVC door shutter with MS square tube 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC sheet stirip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top,lock and bottom rail on either side & as gap insert for top rail & bottom rail .panelling of plain colour PVC sheet to be fitted in the MS frame welded /sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement S&F in the steel frame at site as per specification.

S & F for box type steel ventilators with two top hung shutter (One with pin headed glass pane and other with wiremess) and at bottom segment fixed with pin headed glass including hinges, steel peg stay complete all as specified. Note: - Glass pane and wiremesh shall be measured and paid separately.

M & L stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified.

S & F for 100 mm long Aluminium anodised Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified.

S & F for 150 mm long, aluminium, anodised, barrel tower bolts of extruded section complete all as specified.

S & F for 150 mm size aluminium handles, cast type, anodised complete all as specified.

S&F 100mm size medium wt butt hinges aluminium anodised all as specified.

M & L for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as spd.

S & F for 4mm thick pin headed sheet glass, ordinary quality and glazing with oil putty in squares n. exc 0.5 Sqm in each pane complete all as specified.

Demolition of brick work or stone boulder masonary of any description in and any position built in cement mortar or cement lime mortar complete.

M&L brick wk with Fly ash bricks (old sized bricks), straight or curved on plan exc 6 m mean radius built in CM 1:4 for manholes complete all as specified

M & L Brick work with fly ash bricks (Half brick), straight or curved on plan exc. 6 m mean radius built in CM 1:4 complete all as specified.

Taking up or down 15mm bore steel tubing and connections, including cleaning for re-fixing or removal to store complete.

S & F GI tubing 15mm dia medium grade with all fittings and fixed to wall, floor and ceiling etc complete all as specified.

Fixing only of old steel GI tubing, 15mm bore and connections in new or old position (walls, ceiling, floors etc) complete

Taking up or down 20mm bore steel tubing and connections, including cleaning for re-fixing or removal to store complete.

S & F for GI tubing 20mm dia medium grade with all fittings and fixed to wall, floor and ceiling etc complete all as specified.

Fixing only of old steel GI tubing, 20mm bore and connections in new or old position (walls, ceiling, floors etc) complete all as specified.

Taking up or down 25 mm bore steel tubing and connections, including cleaning for re-fixing or removal to store complete all as specified.

S & F for GI tubing 25 mm dia medium grade with all fittings and fixed to wall, floor and ceiling etc complete all as specified.

Fixing only of old steel GI tubing, 25 mm bore and connections in new or old position (walls, ceiling, floors etc) complete all as specified.

S & F as in repair, 15 mm bib taps, brass, chromium plated, fancy type, long nose, with capstan head handle screwed down high pressure, including CP brass wall flanges; screwed for 15mm bore pipe connection complete all as specified.

S & F as in repair, 15 mm pillar taps, cast copper alloy, with capstan heads, fancy type, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified.

S & F as in repair, 15 mm angle valve, brass, chromium plated, fancy type, with capstan head handle screwed down high pressure, including CP brass wall flanges; screwed for iron pipe connection complete.

S & F for Health faucet, brass, chromium plated, heavy duty, including flexible pipe suitable for 15mm bore water connection; for EWC fixed in repair Complete.

S & F for Shower rose, round type brass, chromium plated, 140mm dia with or without swivel joint, with & including CP brass arm and wall flange, fixing to steel pipe or union as in repair complete.

S & F Soap dish, brass, chromium plated, heavy duty, fixed to wall with plugs with brass cadmium plated screws, fixed in repair complete all as specified.

S & F tubular towel rails, brass, chromium plated, heavy duty, D-type, 20mm dia & 60cm long between flanges fixed in repair complete all as specified.

S & F as in repair, gun-metal, of 20 mm globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed complete all as specified.

S & F as in repair, gun-metal, of 25 mm globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed complete all as specified.

Dismantling water tanks and removing to store exceeding 250 ltrs but not exceeding 500 ltrs complete all as specified and as directed.

S & F two layer ISI marked rotational moulded polythylene water storage tanks tripple layer Black in colour (cylindrical vertical with closed top) of 500 litres capacity, hoisted and fixing in position including connecting up pipes complete all as specified.

S & F 20 mm ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed. (Minimum weight 15mm-142 gms/ 20mm-210 gms/25mm-455gms/40mm- 690 gms/50mm-1240 gms) all as specified.

S & F as in repair, PVC flexible connections 450mm long 15mm dia with brass flange nuts & washers complete. Make: Prayag/Polytuf or equivalent as approved by Engr-in-Charge.

S & F as in repair, 75 mm dia CI floor trap including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified.

S & F stainless steel grating suitable for 125 mm dia bore fixed with white cement with outer square frame, complete all as specified as directed by Engineer-in-charge .

S & F stainless steel grating suitable for 125 mm dia bore with hole fixed with white cement with outer square frame, complete all as specified as directed by Engineer-in-charge .

Demolition in concrete of any description and in any position not otherwise specifically provided.

M & L for 75mm thick PCC 1:3:6 C2 using 40 mm graded stone aggregate as in plinth protection laid in panels and finished even and smooth without using extra cement complete all as specied and directed.

M & L for PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in filling in sunken portion complete all as specified.

M & L rendering 10 mm thick wall plaster in CM 1:3 even & smooth without using extra cement complete all as specified and directed.

M & L for applying a layer of hot blown bitumen of 85/25 penetration grade @ 1.20 Kg/Sqm incl cleaning the surface of roof or sunken etc complete all as specified.

M & L for polythene film, 150 micron thick, laid on a coat of bitumen primer, @ 0.30 to 0.50 kg per sq. m all as specified.

Dismantling and disconnecting of existing CI soil vent pipe upto 100 mm bore fixed to wall,laid in trenches incl all fittings & accessories.

S & F 100 mm dia (Spun pipes) Cast Iron soil waste & vent pipes in any length with or without ears, with cement joints laid in trenches or in floors.

S & F 100mm dia Cast Iron soil waste & vent pipes in any length with or without ears, with cement joints but fixed to walls with & including fixing clamps.

Ditto all as per item no 68 above but except pipes.

Dismantling and disconnecting of existing CI soil vent pipe upto 75 mm bore fixed to wall,laid in trenches incl all fittings & accessories.

S & F 75mm (Spun pipes) dia Cast Iron soil waste & vent pipes in any length with or without ears, with cement joints laid in trenches or in floors.

S & F 75mm dia Cast Iron soil waste & vent pipes in any length with or without ears, with cement joints but fixed to walls with & including fixing clamps

Ditto all as per item no 72 above but except pipes.

Dismantling and disconnecting of existing CI soil vent pipe 50 mm bore fixed to wall,laid in trenches incl all fittings & accessories.

S & F 50 mm (Spun pipes) dia Cast Iron soil waste & vent pipes in any length with or without ears, with cement joints but fixed to walls with & including fixing clamps

Ditto all as per item no 75 above but except pipes.

Extra over cast iron pipe and fittings if lead joint is provided in lieu of cement joint for 75 mm pipe.

Extra over cast iron pipe and fittings if lead joint is provided in lieu of cement joint for 100 mm pipe.

S & F in repairs 100 mm dia branch piece single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches with oval access door all as specified.

S & F in repairs 75 dia branch piece single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches with oval access door all as specified.

S&F in repairs 75 mm bore CI bends (any radius), diminishing pieces or tapers (larger bore measured) with oval access door complete all as specified.

S&F in repairs 75 mm bore CI bends (any radius), diminishing pieces or tapers (larger bore measured) without oval access door complete all as specified.

S & F in repairs 100 mm bore CI bends (any radius), diminishing pieces or tapers (larger bore measured) with oval access door complete all as specified.

S & F in repairs 100 mm bore CI bends (any radius), diminishing pieces or tapers (larger bore measured) without oval access door complete all as specified.

S & F in repairs 100 mm bore CI tee (any radius), diminishing pieces or tapers (larger bore measured) with oval access door complete all as specified.

S & F in repairs, 100 mm CI bends (any radius) with duck's foot or heel rest complete all as specified.

S & F as in repair, 100 mm cast iron sanitary connection socket in fit WC out-let complete all as specified.

S & F for cast iron vent cowls 100 mm dia complete all as specified.

S & F for cast iron vent cowls 50 mm dia complete all as specified.

S & F stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays. Including bolts and nuts and securing ends of stays to wall or roof for 50 mm bore all as specified.

S & F stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays. Including bolts and nuts and securing ends of stays to wall or roof 75 mm bore all as specified.

S & F stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays. Including bolts and nuts and securing ends of stays to wall or roof 100 mm bore all as specified.

M & L for vitreous china wash down water closet (pedestal pattern) complete, including connection to drain pipe and to flushing pipe antisyphonage pipe etc white / ivory in colour, fixed in repair, complete all as specified and as directed.

S & F Plastic water closet seat WHITE COLOUR closed pattern with flat bottom and cover and mild steel chromium plated hinging devised fixed Complete.

S & F in repair Vitreous china wash hand basin, white, oval shape including 32mm dia CP brass waste coupling, 32mm dia PVC waste pipe, cast iron brackets and making good disturbed surfaces in cement mortar 1:3 or PCC 1:2:4 complete all as specified.

M & L for vitreous china squatting pan of Orissa patten of size 580 x 440mm white, back inlet with integral foot rests including connection to trap and to flushing pipe, anti-syphonage pipe etc, fixed in repair complete and making good to floor in cement mortar 1:3 incl S & F trap for pan complete all as directed and specified.

S & F PVC valve less, syphonic action type, fluhsing cistern, 10 ltrs capacity, low level, white, with inlet, ball valve, float and handle including 32mm bore PVC flushing pipe, brackets and fixed in repairs including taking down existing flushing cistern of any description complete all as specified.

Taking down cement plaster/terrazo finish on brick or stone walll etc including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed

M & L for 10mm thick Rendering in cement mortar 1: 6 on fair faces of brick work or concrete surfaces, finished even & smooth without using extra cement complete all as specied and directed.

M & L for 15mm thick Rendering in cement mortar 1: 4 on fair faces of brick work or concrete surfaces,incl water proofing liquid finished even & smooth without using extra cement complete all as specied and directed.

M & L for 5 mm thick Rendering in cement mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement complete all as specied and directed.

M & L for rendering 10mm thick in cm 1:4 as setting coat and 5 mm thick in cm (1:4) as finishing coat as in chajja with WPC. Note: - WPC should be measured and paid separately.

M & L for preparing new plastered or unplastered surfaces of walls and applying two coats of cement base paint over & incl a coat of primer complete all as specified and directed.

M & L for preparing new plastered or unplastered surfaces of ceiling and applying two coats of OBD over a coat of primer complete all as specified.

M & L for preparing new plastered or surfaces of walls and applying two coats of distemper oil emulsion, white or tinted over & incl a coat of primer over & incl 3mm thick Birla white putty complete all as specified.

Removing building materals etc., (other than spoil payable under items 99 to 102 in Section 3-Earthwork) to a distance 5 km or under, beyond the lead included in the rates, including loading, unloading and stacking at the destination all as specified.

Cutting chases, pining in, making good to facings where required and pointing in cement mortar 1:3, for concealed water tubing etc and maing good, cutting exc 10cm and not exc 20 cm girth complete all as specified.

S & F in repairs, Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe) with spreader and urinal waste pipe complete all as specified.

M & L for cast iron gully traps, square or round mouthed, type `P' of size 100 x 100 complete all as specified.

Forming jambs, etc. in CM 1:4, to openings (to foregoing item), with stone supplied by MES including cutting, toothings and properly bonding into old work, including facing and pointing (if necessary) to match existing work, complete

M&L 40 mm thick for damp course to horizontal surfaces in cement concrete 1:2:4 type B-0 using 12.5 mm graded crushed stone aggregate incl all necessary form work

M&L Jodhpur stone of roof slab self faced 7.5cm to 10 cm thick 25 to 35 cm wide hoisted and set jointed and grouted in cement and sand mortar 1:6 comp.all as specified.

M&L PCC 1:3:6 type C-1 using 20mm graded stone agg. ,50mm thick as in floors over stone patti roof slab finished the surface even and fair comp.all as specified.

M&L for flush pointing in cement mortar 1:4 over stone patti in slab complete

M&L for 10 mm thick Rendering in cement mortar 1: 4 on concrete surfaces, finished Fair & even including mixing water proofing compound as per manufacturer's instns( WPC to be measured separately as supply only)

M&L for bitumen blown any grade , applied hot , two caots, to concrete surfaces at the rate of 1.5 Kg Per Sqm Per Coat. Complete.

M&L for Lime concrete terracing as specified on roof complete all as specified and as directed by Engineer-in-Charge.

M&L 40 mm thick Brick tiles bedded in 15 mm thick cement and sand mortar (1:6) and joints grouted flush in cement and sand mortar (1:3) mixed with 5% of crude oil by weight of cement complete all as specified and as directed by Engineer-in-Charge.

M&L for 10 mm thick rendering on fair faces of brick /concrete surfaces in cement mortar 1:4 and finished rough for receiving tiles as in dado complete all as specified.

M&L for Non-skid ceramic coloured tiles (square/rectengular) 7 to 8 mm thick, area of each tile exc 0.06 sqm but not exc 0.11 sqm as in floors, set and jointed in neat cement slurry and pointed in coloured cement to match the surface complete all as specified and directed.

M&L for 25mm thick PCC type B-0 using 20mm graded crushed stone aggregate as in sub base for laying floor finishes complete all as specified

M&L for screed bed or bedding layer 15 mm thick in cement mortar 1:4 for laying floor finishes complete all as specified.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails. M.S frame shall bw covered with heat moulded plain colour PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and botom rail on either side & as gap insert for tip rail & bottom rails; Panelling of plain colour PVC sheet to be fitted in the MS frame weloded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement. suppling and fixing in the frame at site as per specification & drawing

S&F steel ventrilatiors both shutter galzed and gauged (box type) factory made with side hung shutters including pintol hinges, steel handles, steel peg stay and all locking arrangement complete with glazing/gauging bars dovetailed or welded including one shop coat of red oxide primer complete all specified. Note : i) The window shall be fabricated as per Drg No CEBTZ/888R & 889 Sheet 1 to 4 ii) MS fillets, glazing, wire gauge shall be measured and paid separately.

M&L for rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 and 5 mm thick in CM 1:4 as second layer incl. mixing water proofing compound and finished fair and even without using extra cement.

M&L for 15 mm thick Roug Cast Plaster upto height 1.2 m from Plinth Level complete all as specified and as directed.

S&F Cast Iron Pipe (Sand Cast) for waste and vent pipe with or without ears, with cement joints fixed to walls, 50mm dia.

S&F Cast Iron Pipe (Sand Cast) for waste and vent pipe with or without ears, with cement joints 100mm dia laid in trenches.

S&F Cast Iron Pipe (Sand Cast) for waste and vent pipe with or without ears, with cement joints 75 mm dia laid in trenches.

S&F CI floor trap with grating including jointing to waste pipe fixed in cement concrete type B-1 1:2:4, 100 mm dia.

S&F CI nahni trap with grating including jointing to waste pipe fixed in cement concrete type B-1 1:2:4, 75 mm dia.

S&F bends (any radius), disminishing pieces or tappers(larger bore measures), 100mm dia with access door.

S&F bends (any radius), disminishing pieces or tappers(larger bore measures), 75mm dia with access door.

S&F branch pieces ,Double (equal or unequal ) ordinary or inverted (spigot or socket type) or with parallel branches 100 mm dia.

S&F CI cowls , 50mm dia complete all as specified and as directed by Engineer-in-Charge.

Stack clamp out of 50mm x5mm flat iron stays including bolt and nuts and securing ends of stays to walls or roof for 50mm bore piece.

S&F Viterous china wash down water closet pan pan (pedestal pattern ), white (excluding flushing cistern , flush pipe.

S&F pvc white/coloured seat cover any pattern size incl all necessary hinges

S&F Hand shower ( health faucet ) brass body with 8mm dia 1 meter long SS braided flexible tube with wall hook.CG 105A

S&F vitreous china wash hand basin white flat back, size 550x400 including 32mm CP waste coupling, PTMT PVC connections 15mmX450mm, 15mm dia fancy type CP Pillars Taps , 15mm dia stop valve, CP fancy type, Shelf of PTMT fixed with CP Brass screw and wood etc complete all as specified.

S&F Towel ring of PTMT with and incl chromium plated brass screws and wooden /plastic cleats

S&F PTMT glass shelf with and including chromium plated brass screws and wooden cleats

S&F chromium plated stop cock/angular stop cock , with crutch or butterfly handle screwed down screwed for iron pipe or brass ferrule, fancy type, CP, 15mm dia complete all as specified and as directed by Engineer-in-Charge.

S&F 15mm bore PVC connection with PTMT nuts.

S&F chromium plated paper holder fancy type complete all as specified and directed

M&L for hardcore of gauge nexc 63mm , deposited , spread and levelled in layers nex 15cm thick watered and rammed to a true surface

Gun Metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as dircted by Engineer-In-Charge.

S&F 1000 ltr Rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I, 450 ltr Capacity, including Ball brass valves, high pressure, with polythene float and flynut com

S&F 20 mm bore brass valve high pressure with polythene float and fly nuts complete screwed for iron pipe

S&F Steel water tubing 15mm bore medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows , tees, short pieces, connectors, back nuts, diminis

S&F 15mm bore stop valve cast copper alloy screwed down under high presssure with crutch or butterfly handle screwed for pipe or brass ferrule complete all as specified and as directed by Engineer-in-Charge.

M&L for preparing newly plastered surfaces of walls and applying three coats of white wash.complete all as specified and as directed by Engineer-in-Charge.

M&L for extra for forming fair finished drain or channel 30cm inner girth in cement concrete ,using extra cement ,incl forms moulds ,mitered/stopped ends etc

M&l Soakage wells of Size 1.8 m dia x 3.0m effective depth excavation, in any type of soil , foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M-25 concrete including intercepting chamber and screen chamber made of brick masonary in CM, RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/DWC complete all as per CEBTZ TD Drg.and as directed by Engineer-In-Charge.

Dismantling of existing false ceiling of boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and as directed by Engineer-in-Charge.

Dismantling Asbestos cement Corrugated sheets in roof covering including ridges .

Taking down cement plaster on brick or conc surfaces including racking out joints hacking for key, scrubbing down with water etc.

Taking down chowkhat or frames exc 1.50 Sqm n.exc 4 Sqm (without taking down shutters from the frames)

Ditto all as per item no 159 above but n.exc 1.50 Sqm

Demolition floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises.

Demolition of wrought iron or mild steel work of any description not other wise provided of for

Dismantling timber scantling 40 sq cm and over in section, in any position complete.

M&L for pre painted galvalume aluminium zinc cozting GI based corrugated steel Sheet high rib profile tile pattern of slaty/green color coated 0.5 mm thick of 550 Mpa Tensile strength sheets as in roof covering and fixed as per manufacturers instruction (design as app by Engg in charge complete all as spfd )

M&L Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

S&F Composite cement ceiling board 4 mm thick in ( 595 mmX595 mm ) pannel (Make-everest ramco or eql.) designer ceiling pre finished conforming to IS 14862 type B cateogory three incl GI frame , grid work,hold fast,suspended with suspender along with holding down bolt complete . (Note: Ceiling board shall confirming to IS-14862 ,shall be fire resistant , Moisture resistant and ceiling shall be suspended with suspenter and adjuster .)

M&L for providing 75 mm thick cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregates as in plinth protection finished even and smooth without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified.

M&L for machine cut kota stone flooring 20-25mm thick over cement screed base laid and jointeed with pigment to match the shade of the slab including rubbing and polishing all as spd and as directed by Engineer-in-charge.

M&L for Kota stone slab 18-20mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified.

Cutting & grinding to existing kota stone flooring and polishing grinding upto mirror finish complete

M&L for screed bed or bedding layer of mortar 15mm thick in cement mortar 1:4 laying floor finishes complete all as specified.

M&L Jodhpur stone of roof slabs, self faced 5.00 cm thick, as in shelves , chajjas shelves etc nexc 2 m in length., hoisted and set, jointed and grouted in lime mortar 1:3 or cement mortar 1:6 complete

M&L Mild steel framed work such as grills, gratings, tank staging etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bar; barred iron doors; ladder; framed balusters; railing;frame work for water tanks, cooler stand and similar work conforming to Fe 290 Gd E-165 all as specified .

M&L steel work in tubular trussess/ purlins incl spl shaped washer etc. using ERW or induction butt welded tubes confirming to IS 1161-1979 grade St-240. complete all as specified and directed by Engineer-In-Charge.

M&L Mild steel bolts.exc. 5 cm length not exc. 10 cm length (machine made) with hexagonal or square heads at one end and screwed the other , or screwed both ends, each screwed end to be fittied with washers and one hexagonal or square nut 11 to 15 mm neck dia complete all as specified and as directed by engineer-in-charge.

M&L Mild steel plates (Plain or chequred) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachement complete all as specified.

M&L for mild steel work as in plates / flats angles etc as in cleats drilling welding etc

S&F 125 x 60mm pressed steel frames for doors with one or more rebate including necessary fixing lugs, hinges lock strike plate etc complete as specified including a coat of shop coat zinc chrome primer.

M&L PCC 1:3:6 type C-1 using 20 mm graded stone aggregate as in filling in pressed steel frames complete all as specified and as directed by Engineer-in-Charge

S&F 35mm thick Factorymade second class hard wood plain framed pannelled shutter (two panels and double shutter) with lock rail and pannel or 9mm BWP comerical ply or 12mm venered particle board with comerical face venering on both faces. The size of rail and style as per IS-1003 part kilin seasoned

S&F 2nd class hardwood 35 mm thick glazed and skeleton shutters, open rebated and prepared to receive glass guage, etc. (without sash bars), edges of framing plain, chamfered or rounded. Fitted with cut and mitred beads for securing glass,etc. sizes of members of shutters as specified in SSR Part I, section 8, clause 8.24(a); supplied and fitted to chowkhats complete all as specified and as directed by Engineer-in-charge.

S&F mild steel barrel tower bolt, stove enamelled black with bright bolt of 200 mm complete.

S&F mild steel sliding door bolts plate type stove enameled black with bright bolt not less than 12 mm dia with and incl. a minimum of 6 bolts and nuts four on bolt plate and two on staple plate of 300 mm long complete all as specified and as directed by Engineer-In-Charge.

S&F MS pressed handle oval type stove enamel block with bright bolt of 150 mm. complete.

S&F brass 300 mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed by engineer-in-charge.

S&F in replacement curtain rod 25mm dia, mild steel, chromium plated, fancy type with fixing brackets and knobs at both ends as per site requirement complete all as specified and directed by Engr-in-Charge Note :- The cost of brackets and knobs is deemed to be incl in the quoted rate. Nothinbg extra shall be paid on this account.

S&F stain less steel peg set with 06 no of hooks mounted on SS plate 4 mm thick with and including screws .

S&F factory made mild steel Window box type with side huge shutters incl pintol hinges,steel handles, steel peg stay and all locking arrangement and one shop coat of red oxide primer complete all specified. Note : i) The window shall be fabricated as per Drg No CEBTZ/TD/888R & 889 ii) MS fillets, glazing, wire gauge shall be measured and paid separately iii) opening incl provn shutter for cooler to be provided

S&F 4 mm Sheeet glass ordinary quality and glazing with oil putty in square n exc. 0.5 sqm in each pane complete all as specified and as directed by Engineer-in-Charge.

M&L Galvanised stain less steel wire cloth 0.56 mm nominal dia of wire anfd averqagae width of aperature 1.18mm and fixed with tinned tracks, or galvanised wire spaples.

M&L for two coats of synthetic enamel paint on new wooden surfaces incl prep over a coat of pink primmer complete all as specified and as directed by Engineer-in-Charge.

M&L for broken stone or boulders Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified.

M&L Sand cuhsioning under floors complete all as specified and as directed By Engineer-In-Charge.

M&L Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade laid complete all as specified and as directed by Engineer-in-Charge.

M&L For PCC type B1(1:2:4) using 20 mm graded cushed stone agg as in coping ,benching and the like incl form work complete all as specified and as directed by Engineer-in-Charge.

M&L for cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate in foundations, filling and mass concrete complete.

M&L for 100mm thick Cement concrete 1:2:4 type B-2 using 40mm graded stone aggregate in floors and paving, laid in panels and finished even & fair complete.

M&L 100 mm thick plain cement concrete type D-2 ,1:4:8 , using 40 mm graded crushed stone aggregate as in sub base flooring complete all as specified and as directed by Engineer-in-Charge.

S & F 28 mm wide plastic dividing strips 1.50 mm thick complete all as specified and as directed.

M & L for Mild steel plate girder or single stanchions, built up of one beam or channel section with flange plates, caps, bases, splices,angle brackets, cleats and other connections Gde Fe410-0 or Fe 310-O.

M&L Mild ateel Roof trusses (framed), trussed purlins crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle channel or flat sections) including distance pieces, cleats etc.

M&L Mild steel Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates

M&L Mild steel Plates (plain or chequered) channels. Square cut or notched (ordinary and counter sunk) forming holes, without any attachment confirming to GDE Fe410-0 or Fe 310-O

S & F 5 to 10 mm dia mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, each screwed end to be fitted with washers and one hexagonal or square nut, Ditto, but length of bolt exc 15cm and n exc 22.5cm long.

Excavation in trenches in soft/loose soil, n. exc. 1.5 m wide and n. exc 1.5 m in depth; for foundaton, etc. or for shafts, well, cesspits, manholes, pier holes and getting out.

M & L for Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm.

Removing excavated material not exc. 50m and depositing where directed at a level not exc. 1.50m above the starting point in soils

Excavating in post holes (or similar holes) in soft/loose soil, each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm,

M&L for Cement concrete 1:4:8 type D2(40 mm graded stone aggregate) in foundation filling and mass concrete.

M & L brick work with sub class 'B' bricks straight or curved on plain texc 6m mean radius built in cm 1:6

M & L for Cement concrete 1:3:6 type C-2 bed to drain pipes including packing under, and haunching against the sides of pippe after they are laid and tested; in 150mm dia pipe.

S&F salt glazed stone ware drain pipe 150mm bore in trenches and jointed as spfd

Providing cement concrete as in surface channels and drains type B1 1:2:4 using 20mm graded agg and inside the man holes.

S&F mild steel TMT bar 6 to 8 mm dia and over as in reinforcement, cut to length, bent to shape etc including binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M & L RCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in precast cement concrete, manhole covers including all use of forms, moulds or machine moulds and setting the blocks, slabs etc in cement mortar 1:4,complete all as specified and directed. (Reinforcement shall be measured and paid separately under respective item of schedule "A")

M&L Soakage wells exc, in ordinary Soil, Foundation in PCC 1:3:6, wells of Honey combed and solid in M-25 Concrete, including intercepting chamber, screen chamber Brick work in CM, RCC cover slab in M-25/ RR masonry / Filling with brick bats, complete of size 3.0 M dia X 6.0M deep all as per CEBTZ Drg and all as directed .

Taking down carefully (aluminium) point wiring complete of any type (batten/ surface conduit or concealed) for light point, fan point, bell point socket point or power point complete with all fitting such as switches, sockets pendants, ceiling rose, round block etc complete and making good disturbed surfaces of wall, floor or ceiling with plaster of tiles or roof treatment etc and finishing the surfaces with distemper/white washing/colour washing to match with the existing surface complete all as spcified and directed.

Taking down submain wiring Aluminium/ copper of any size including earth continuity condutor on teak wood or conduit and removing from site and making good the disturbed surface of wall etc complete all as specified and directed.

Taking down old U/S existing DB TPN 4 way and DB SPN 8 way including MCB/MCCB of any capacity and any size and removing from site and making good the disturbed surface of wall etc complete all as specified and as directed.

M & L for point wiring with and including single core FRLSH PVC insulated and unsheathed stranded copper conductor cable of size 1.5 sqmm 1100 volts grade drawn through and including suitable size of PVC concealed conduit with accessories with laminated top cover fixed on GI sunken box with modular cover plate for housing of switch, socket, regulator etc complete with and including 1.5 sqmm FRLSH PVC insulated and unsheathed stranded copper conductor cable as earth wire and connected to common earth dolly and making good to the disturbed surfaces of wall, floor, ceiling etc to match with exisiting surface complete all as specified and as directed by Engr-in-Charge for the following :- (a) One Light/fan/ex-fan/Bell/point controlled by one switch.

(b)One pin 5 amps socket point on the same board with other switches complete

(c) One 3 pin 5 amps socket on independent board.

Ditto all as per item No 220 above but with 4.0 sqmm copper wire for 3 pin socket outlet 20 Amp on independent board complete and all as directed by Engr-in-charge.

S&F switch Modular type, 6 Amp, 1 module single pole one way, 230 Volts, Modular type complete all as specified and as directed by Engr- in -charge.

S&F switch Modular type, 16 Amp, 1 module single pole one way, 230 Volts, Modular type complete all as specified and as directed by Engr- in -charge.

M&L socket outlet 3 Pin 6 Amps modular type, 2/3 pin combined 2 module 230 Volts complete all as specified and directed by Engr-in-Charge.

M&L socket outlet 3 Pin 6/16 Amps modular type, 2/3 pin combined 2 module 230 Volts complete all as specified and directed by Engr-in-Charge.

S&F Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amp complete all as specified and as directed by engineer-in-charge.

S&F ceiling rose, surface backelite , three terminal AC, 230 volt complete all as specified.

supply and fixing fan step regulator modular type,120W -2 module electronic socket type five step controlled 230V AC 50 Hz for complete all as specified and directed by Engr-In-Charge.

Removing and Refixing LED tube light fitting, 1x 20-22 watts, 230 volt, basic all purpose surface and wall mounted led batten with polycarbonate housing & integrated electronic driver, pre-wired and fixed on walls with all fixing accessories such as screws, clips etc and connecting up with two core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed by Engr-in-charge.

M & L Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings

S&F sheet metal enclosure MCB DB, double door, vertical TPN 4 way with 200 Amps rated busbar all as specified and as directed. Make:- Hegar/Legrand/Seimens

S & F double door, sheet metal enclosure, powder coated for MCB DB SPN 8 way fitted with neutral link, earth bar , din rail and 200 amps rated bus bar 230 volt conforming to IS 13032-1991 complete all as specified and as directed by Engr-in-charge.

S & F MCB SP, 5-32 Amps , 240 volts, breaking capacity 10KA complete all as specified and as dircted by Engr-in-charge.

S & F MCB DP,D CURVE 40 Amps , 240 volts, complete all as specified and as dircted by Engr-in-charge.

S&F MCCB 100 amps, 4 pole, 415 volts, fixed type breaking capacity 16KA complete all as specified and as directed by Engr-in-charge.

M&L for submain wiring using 2 runs of single core FRLS PVC insulated, unsheathed stranded copper conductor cable of size 2 runs of 6 Sqmm of voltage rating 1100V for Single phase & neutral, drawn in and including concealed PVC conduit of dia not less than 25 mm dia with standard acessories, along with two run of FRLS PVC insulated, unsheathed, stranded copper conductor of size 2x 6.0 Sqmm as earth continuity conductor all as specified and directed(Note-2 runs of single core FRLS PVC cable 6sqmm for Single phase & neutral with Two run of earth conductor as earth and conduit shall be measured as one unit)

Supply and fixing LED mirror light fitting , type with high out put diffuser 2 feet, 5watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.HAVELLS CAT PART NO-ENDURALINEARNEOBS10WLED865SPCWH/WIPRO CAT PART NO-LL20-111-XXX-65NE3/BCLSB 10 WH

Supply and fix desert cooler electric driven (singal phase) having nominal air flow capacity of 4000 CUM per hour, steel body.

Taking down EX fan / fan,sealing cable end,dismantling blades and removing fan and blades & refixing ceiling fan ex fan of any make, any sweep , keeping side in store in safe custody for painting of ceiling fan /ex fan complete,in situ with synthetic enamel paint by spraying including filling cavities with filler,one coat after cleaning all dust and reassembling the fan complete including writing MES No at the site.

Supply and laying Sand coarse dry as in cushioning of under ground electric cable in trenches, laid to a uniform thickness of 23 cm (15 cm under the cable & 8 cm over the cable) and gently punned down to 18 cm thickness all complete as specified and as directed.

Supply and laying bricks (old size) for cable protection by using common burnt clay building bricks, sub-class ‘B’ designation 75 laid dry flat across length of the cable with width of the trenches equal to length of bricks and all as directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16sq mm 4 core complete all as specified and directed.

S&F GI tubing light grade 40mm dia for protection of cable on pole/ wall etc complete all as specified and as directed by Engr in charge.

M&L for Earthing complete with galvanized steel earth plate electrode 60cm x60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 meters deep below normal ground level) with top edge of plate not less than 1.5 meters below normal ground level connecting to the galvanised earth lead wire 4.0 mm dia by means of bolts, nuts check nuts and washers of galvanized iron and steel earth wire protected by provision of GI mediumgrade pipe 15mm bore including provision of concrete pit made with 40mm thick cover of RCC 1:2:4 reinforced with XPM (Weight not less than 4Kg/Sqm) and frame of angle iron 40x 40x6 mm and handle of 6mm dia MS bar made to shape, GI light grade 20mm bore pipe for watering perforated at bottom, 1.75meter long placed on top edge of earth plate, common salt & charcoal filling with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returing filling in and removal of surplus soil to a distance not exceeding 50 meters all as per electrical plate No -5 of SSR 2009 Part-I and connecting to Lighting protection earth test points all as specifed and directed including testing on completion.

S&F switch piano type, 5 Amp, single pole one way, 230 Volts, flush type complete all as specified and as directed by Engr- in -charge.

M&L socket outlet 3 Pin 5 Amps flush type 230 Volts complete all as specified and directed by Engr-in-Charge.

M&L for socket outlet 2 in 1, 3 Pin, 5 & 15 Amps, 230 Volts t complete all as specified & directed by Engr-in-Charge.

S&F LED tube light fitting, 1x 20-22 watts, 230 volt, basic all purpose surface and wall mounted led batten with polycarbonate housing & integrated electronic driver, pre-wired and fixed on walls with all fixing accessories such as screws, clips etc and connecting up with two core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed by Engr-in-charge. Make : Philips-BN021 LED 20S PSU CW GR S2/ Crompton Greaves LDDR20-CDL Dazzle Ray / bajaj-BCLAB 20W

S & F MCB SPN, 6-32 Amps, 240 volts, breaking capacity 16KA complete all as specified and as dircted by Engr-in-charge.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300m

N.K. CONSTRUCTION COMPANY

BIDAWAT ENTERPRISES

G R POWERS