Beautification Illumination and Development of Shree Ravalnath Temple and Development of Parking Area at Shiroda in Ponda Taluka Goa

Amount

CIVIL WORKS

Earth work in excavation over areas of all type of strata comprising of any type of material such as soil ,silt,clay, sand, gravel, murum of all varieties, shingles, pebbles, all type of congolmerates,latrite rock,soft rock,ordinary rock, disintegrated rock,fissured/shattered rock, decomposed rock, weathered rock and all such material either in full or part as the case may be adopting any method/ methods as may be convenient or permitted (blasting prohibited) including chiselling ,wedging,etc., in all conditions such as dry , moist, foul, saturated, submerged, etc., as directed by the Engineer etc., all complete including dressing of side ramming bottom, all leads, lifts and depths including getting out excavated soil & stacking as directed , pumping and bailing out water, barricading,danger lighting, guarding as directed .

Earthwork in excavation by mechanical means (hydraulic excavator)/manual means in foundation pipeline trenches drain (not exceeding 1.5 m in width or 10 sq.m. on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50 m. All kinds of soil

Refilling the pipeline/foundation trenches plinth sides, foundation etc. with available excavated earth in layers not exceeding 20 cm depth consolidating each layer ramming and watering lead upto 50 M and all lifts and disposal of surplus earth as directed by Engineer .

Rubble packing with hard laterite stone under floors including watering ramming and consolidating etc. in pipeline trenches and other foundations complete.

Pre-cast cement concrete solid block masonry of compressive strength 70 kg / cm2 in cement mortar 1:4 (1 cement : 4 corase sand ) in foundation and plinth size of blocks (30 x 23 x 15)

Half brick masonry in cement mortar 1:3 (1cement : 3 coarse sand) with bricks of class designation 75 kg /cm2. Upto floor V level.

Providing & laying cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded granitic or basaltic stone aggregate 20 mm. nominal size) excluding cost of centering, shuttering and finishing in: All work up to Plinth level

Providing and laying in position ready mixed concrete (RMC) manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead upto 10kms having continious agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C., from the transit mixer to the site of laying, excluding the cost of centering, shuttering, finishing and reinforcement including the cost of admixtures in recommended porportions as per IS : 9103 to accelerate/retard setting of concrete, improve workability without imparing strength and durability as per the directions of the engineer-in-charge. All works upto floor V level M-25grade of concrete

Centering and shuttering including strutting, propping, & removal of form for Foundation, footings, bases of columns

Centering and shuttering including strutting, propping, & removal of form for Vertical surfaces such as retaing walls, return walls, Partitions, walls (any thickness) including attached Pilasters, Buttresses, Plinth and string courses, Fillets and the like

Centering and shuttering including strutting, propping, & removal of form for Sides and Soffits of beams, Beam Haunchings, Cantilever, Girders, Bressumers and Lintels plinth beams not exceeding 1m in depth

Centering and shuttering including strutting, propping, & removal of form for Columns, Piers, Pillars, Aburments, Posts and struts (square rectangle polygon in plan)

Centering and shuttering including strutting, propping, & removal of form for Suspended floors, roofs, landings, shelves & their supports

Providing TMT steel reinforcement bars of SAIL, TATA, VIZAG made only (Confirming to IS 1786 of 1986) for RCC work (conforming to I.S. 1786 of 1986) including bending, binding & placing in position in all the floors along with the factory made precast concrete cover blocks of specified sizes whose compressive strength is not less than that of surrounding concrete in the structural member. Minimum Grade of Steel - Fe 500

Steel work welded (SAIL, TATA. VIZAG & using electrodes of Ador or ES4B or Deh Secheron make only)in built up sections trusses and framed work including cutting, hoisting, fixing in position and applying priming coat of red lead paint. In tees, angles, flats and channels

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) (Square Hollow Section (SHS) IS4923 /Rectangular Hollow Section (RHS) IS4923/ Circular Hollow Section (CHS) IS1161 closed Structural Steel of approved make (Min Yeild Stress 310 Mpa)) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Providing and fixing in position 2mm thick one side embossed clear polycarbonate sheet in same profile to match the roofing sheets including self tapping screws.

Providing and fixing M.S. grill of required pattern in wooden frames of Windows etc. with M.S. flats square or round bars with round headed bolts and nuts or by by screws. plain grill

Providing and fixing M.S. Fan clamp type I or II of 16 mm dia M.S. Bar bent to shape with hook ends in RCC slabs during laying including painting the exposed portion of loop, all as per standard design complete.

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc.with hairline finish, including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts,bolts,fasteners etc.).

Providing and and laying antiskid floor tiles 12 x 12 upto 16 x 16 in of Johnson, Somany, Kajaria (thickness to be specified by the manufacturer) of 1st quality conforming to IS:15622 of approved make in shades as specified laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand) including pointing the joints with white cement and matching pigment etc., complete Light Shades

Providing and fixing 1st quality ceramic glazed wall tiles (Johnson, Somany, Kajaria )conforming to IS:15622 (thickness to be specified by the manufacture of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand ) and jointing with grey cement slurry @3.3kg per sq.m including pointing in white cement mixed with pigment of matching shade complete. Wall Ceramic Glazed Tiles : 300 x 600

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer : Flamed finish granite stone slab. Jet black

Providing & fixing 18 mm thk Flame Finish Granite Tread Tiles in single piece in Jet Black with rounded off nosing, antiskid groove laid on 20 mm (average) thick bed of cement mortar 1:4 (1 cement : 4 coarse sand) with neat cement slurry including pointing with pigmented cement slurry to match the shade of slab, cleaning etc. complete. ( Price range 2000 to 2100 Rs per Sq Mtr.)

Providing and fixing Granite stone slabs (mirror polished) 18mm thick in risers of steps, skirting, dado and pillars laid on cement paste and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. Jet black

Providing and laying Polished Granite stone flooring, coping in required design and patterns, in linear as well as curvilinear portions of the building, all complete as per the architectural drawings, with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand), laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade, including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. ( Price range 1550 to 1600 Rs per Sq Mtr.)

Providing and laying factory made Shot blasted cement concrete interlocking paver block of minimum M35/M40 grade made by heavy duty block making machine with strong vibratory compaction and of aprpoved size and design /shape laid in 50 mm thick compacted bed of coarse sand, filling the joints with coarse sand,etc. all complete as per the direction of Engineer.- in I, Wave, Rectangular, Square etc.shapes. The products should comply to IS 15658:2006 and manfucatured by ISO9001:2008 certified plant. The shot blasting should be done using 0.4-0.5mm dia steel shots with a speed of 3200 rpm 60 mm thick in all colours except grey (M35 grade)

Providing and laying factory made Shot blasted cement concrete interlocking paver block of minimum M35/M40 grade made by heavy duty block making machine with strong vibratory compaction and of aprpoved size and design /shape laid in 50 mm thick compacted bed of coarse sand, filling the joints with coarse sand,etc. all complete as per the direction of Engineer.- in I, Wave, Rectangular, Square etc.shapes. The products should comply to IS 15658:2006 and manfucatured by ISO9001:2008 certified plant. The shot blasting should be done using 0.4-0.5mm dia steel shots with a speed of 3200 rpm 60 mm thick in Grey colour (M35 grade)

Providing and laying factory made Shot blasted cement concrete interlocking paver block of minimum M35/M40 grade made by heavy duty block making machine with strong vibratory compaction and of aprpoved size and design /shape laid in 50 mm thick compacted bed of coarse sand, filling the joints with coarse sand,etc. all complete as per the direction of Engineer.- in I, Wave, Rectangular, Square etc.shapes. The products should comply to IS 15658:2006 and manfucatured by ISO9001:2008 certified plant. The shot blasting should be done using 0.4-0.5mm dia steel shots with a speed of 3200 rpm 80 mm thick in all colours except grey (M40 grade)

Providing and laying factory made Shot blasted cement concrete interlocking paver block of minimum M35/M40 grade made by heavy duty block making machine with strong vibratory compaction and of aprpoved size and design /shape laid in 50 mm thick compacted bed of coarse sand, filling the joints with coarse sand,etc. all complete as per the direction of Engineer.- in I, Wave, Rectangular, Square etc.shapes. The products should comply to IS 15658:2006 and manfucatured by ISO9001:2008 certified plant. The shot blasting should be done using 0.4-0.5mm dia steel shots with a speed of 3200 rpm 80 mm thick in grey colour (M40 grade)

Providing and fixing 18mm thick polished black granite machine cut for kitchen platforms, counters, window sills, Door Frame, Urinal Partitions , fascia and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing,moulding and polishing to edge to give high gloss finish, etc. complete at all levels.( Price range Rs.1500 to Rs.1700 per. Sq.M )

Providing 25mm thick cuddapah slabs machine cut and polished on either side in partitions including making necessary grooves in the wall and fixing with cement mortar, complete as directed by the engineer.

Supplying and fixing Pre-cast cement concrete kerb-stones(factory made,the factory should be ISO certified and registered under Dirctorate of Industries, Govt. of India) of M-20 with 20 mm nominal size granitic/basaltic aggregate properly consolidated by mechanical plat-form and vibrators with smooth finish including fixing at site complete as per specification. Size 60 cm L x45 cm H x 15 cm T

Kotah stone slab flooring over 20 mm (average) thick base laid over & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & complete with base of cement mortar 1:4 (1 cement : 4 coarse sand) 20 mm thick.

Providing water proofing treatment over the new R.C.C. roofs terrace by spreading cement slurry over the R.C.C. slab and laying of 10cms. Average laterite stone ballast coba with the necessary gradient for easy flow of rain water and the coba in covered with damp proof of Hindustan water proofing co. Or equivalent jointless water proofing plaster of mix 1:3 (1 cement: 3 find sand), finished smooth with wooden trowel with false marking of 30 cms square. The vertical surface of the adjoining walls are to be treated upto a height of 30cms including rounding of junction (the rate includes for complete items including labour and materials and including cost of initial treatment of roof slab as follows. The injunction of damp proof or equivalent compound with cement solution will be given as and when found necessary for filling honey comb, cracks etc. in the R.C.C. slabs). NOTE: cement consumption 25 kg/sq.m.

Providing and fixing waterproofing treatment to sanitary blocks consisting of layers of Laterite stone coba of 75 mm thick in cement mortar 1:2 sand witched between two layers of cement mortar 1:4 (20 mm thick ) mixed with water proofing compound, top finishing coat of cement slurry 6 to 12 mm thick with water proofing compound etc. complete with 32 mm dia PVC pressure relief pipe of adequate length including waterproofing treatment to 750 mm height (maximum) of side wall, and bottom surface in cement mortar 1:4 with waterproofing compound and covering 10 years guarantee on court fee stamp of Rs. 100 with ponding test including all lead, lift etc. complete as directed by Engineer.

12 mm thick cement plaster 1:4 (1 cement:4 fine sand)

6mm thick cement plaster to ceiling with 1:3 (1 cement : 3 fine sand)

18mm cement plaster in two coats under layer 12mm thick cement plaster 1:5 ( 1 cement : 5 coarse sand) and top layer 6mm thick with cement plaster 1: 3 (1 cement : 3 coarse sand) finished with sponge.

Extra for providing and mixing water proofing material proportion recommended by the manufacturers. (a)12mm cement plaster 1: 3 (1 cement : 3 sand)

Providing and applying white cement based putty of average thickness 1.00mm of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Wall painting (two or more coats) with plastic emulsion paint of approved brand and manufacture on new work to give an even shade.

Painting three or more coats with acryllic exterior paint of approved brand and manufacture (such as weather shield,APEX) including applying one coat of cement primer and one coat of surface treatment etc. complete.

Painting (two or more coats) with synthetic enamel paint of approved brand and manufacture in all shade or new work over and under coat of suitable shade with ordinary paint of approved brand and manufacture to give an even shade

Providing & fixing 19mm thk plywood work in frames of doors using 19mm marine ply (waterproof) with all hardware,and other frames and fixed in position with 50 mm fastners etc. complete as specified as shown in the drawings.

Providing and fixing first class Indian teak wood moulded beading to door and window frames with iron screws , plugs and priming coat on unexposed surfaces etc. 50x12mm size.

Providing and fixing block board flush door shutters 35mm thick ( 1st Class Teak ply on both faces), laminated on both sides with 1mm thick laminate of approved brand and colour including cost of Adhesive, Nails, screws during fixing etc. complete.

Providing & fixing bright finished Stainless Steel mortise latch & lock with 60 mm Cylinder and a pair of levers, handles with necessary screws etc.complete

Providing and fixing bright finished brass door latch with necessary screws etc complete. 300x 16 x 5 mm

Providing and fixing chromium plated brass butt hinges with necessary screws etc. complete Size 125 x 70 x 4.0mm

Provided and fixing 150 mm chromium plated brass floor door stopper with rubber cushion screws etc. to suit shutters thickness complete.

Providing and fixing bright finished brass tower bolts (barrel type) with screws etc. complete 200 x 10 mm

Providing FRP door shutters 35mm thick with frame size in clear opening of 0.75x2.10m hinges and screws complete.,

Dismantling the tile work in floors and roofs laid in cement including stacking of materials within 50 meters lead for thickness of tiles 10mm to 25mm.

Taking out existing CC interlocking paver blocks from footpath/ central verge, including removal of rubbish etc., disposal of unserviceable material and stacking of serviceable material within 50 metre lead as per direction of Engineer-in-Charge.

Providing and fixing anodized aluminum ventilators (including frame and shutter ) with three partitions with 5 mm thick approved clear float glass in one partition, Exhaust opening in one partition & 6 mm thk glass louvers in one partition with using weight and size of section not less then as specified or as shown in drawing ,locking arrangement,silicon sealant ,EPDM gaskets, including all aluminum fixture and fittings etc. complete . All gaps between civil work and aluminium frames shall be sealed and made watertight by applying silicone sealant.Rectangular tube @0.478kg/m

Providing and fixing of aluminium window with 3 tracks and 2 shutters sliding window with tobular frame ployster powder if thicness 75-80 microns with approved standard accessaries such as ball beaing rollers, concealed lock, 6mm thick plain clear glass with EPDM beading etc.

Drilling 150 mm deep hole in R C C and grouting the rebar with lockfix etc complete. 10 mm Dia

Drilling 150 mm deep hole in R C C and grouting the rebar with lockfix etc complete. 12 mm Dia

Providing and laying non-pressure NP2 class (light duty) RCC pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand ) including testing of joints, etc. complete. 250 mm dia RCC pipe

Constructing soak pit 1.20m x 1.20m x1.20m filled with laterite stone aggregate 125 to 180 mm including S.W. drain pipe 100 mm diameter and 1.2m. Long complete as per standard design

PLUMBING WORKS

Providing and fixing white vitreous china type water closet squatting pan (european type w.c. pan) with Dual Flushing (citren Nelson/ similar)with stop cock wall flanges flush pipe or elbow and vacuum breaker coupling etc. including cutting making good the walls and floors where required. (excluding handicap toilets)

Providing and fixing Hand Shower (Health Faucet) with 8mm dia, ABS/brass body with double lock 1.00m long Flexible tube (Brass plated stainless steel flexible hose) and wall hook of approved quality confirming to IS standards. (all EWC including Handicap toilets)

Providing and fixing NICKEL chrome plated copper alloy Fancy long body bib cock with wall flange Jaquar make or equivalent. Confirming to IS 8931;1993 for orissa pan. 15mm nominal bore

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430 x 260 x 350 mm and 340 x 430 x 265 mm sizes respectively with PVC automatic flushing cistern with fittings, R.S. or C.I. brackets, standard size galvanized steel flush pipe and spreaders with brass unions & G.I. clamps complete, including painting of cistern and fittings, cutting and making good the walls and floors where required. (a)One urinal basin with 5 liters p .v .c. automatic flushing cistern.

Providing and fixing vitreous china wash basin with RS or C.I. brackets painted white, 15 mm C.P. brass pillar taps C.P. brass chain with rubber plug 32 mm C.P. brass waste of pattern, 32 mm diameter M.I. or C.P. brass trap and union complete, including cutting and making good the walls where required. Flat back wash basin size 550 x 400mm with a single 15 mm C.P. brass pillar taps.

Providing and fixing NICKEL chrome plated copper alloy Fancy BOTTLE TRAP ECONOMY TYPE 32MM Jaquar make or equivalent. Confirming to IS 8931;1993

Providing & fixing liquid soap container with C. P. brass lid and brackets fixed to wooden cleats with C. P. brass screws Plastic container

Providing and fixing nahani trap of rigid PVC (approved make) for S.W.R. Pipes including lubricating etc. complete, without door : 110mm

Providing and fixing nahani trap of rigid PVC (approved make) for S.W.R. Pipes including lubricating etc. complete, without door : 75mm

Providing and fixing NICKEL chrome plated copper alloy Fancy wall mixer with 3 IN 1 SYSTEM WITH 115MM long bend pipe for connection to over head shower Jaquar make or equivalent. Confirming to IS 8931;1993

Providing & fixing c.p. brass towel rail complete with C.P. brass brackets fixed to wooden cleats with C. P. brass screws 750X20

Providing & fixing soap dish chromium plated with brackets fixed to wooden cleats with CP brass screw

Providing and fixing rigid PVC S.W. R. (soil, waste and rain water drainage pipes of approved make including lubricant etc. complete (single/double) socket-ed : 110mm dia

Providing and fixing rigid PVC S.W. R. (soil, waste and rain water drainage pipes of approved make including lubricant etc. complete (single/double) socket-ed : 75mm dia

Providing and fixing rigid PVC bend of required degree (of approved make) for S.W.R. drainage pipes of approved including lubricating. 110mm

Providing and fixing rigid PVC bend of required degree (of approved make) for S.W.R. drainage pipes of approved including lubricating. 75mm

Providing and fixing rigid PVC bend (approved make ) for S.W.R. pipes including lubricating etc complete bend with door : 110mm

Providing and fixing rigid PVC bend (approved make ) for S.W.R. pipes including lubricating etc complete bend with door : 75 mm

Providing and fixing single Tee of rigid PVC (approved make ) for S.W.R. pipes including lubricating etc complete, with door : 110mm

Providing and fixing single Tee of rigid PVC (approved make ) for S.W.R. pipes including lubricating etc complete, with door : 75mm

Providing and fixing single “Y” of rigid PVC (approved make ) for S.W.R. pipes including lubricating etc complete, without door 110mm

Providing and fixing single “Y” of rigid PVC (approved make ) for S.W.R. pipes including lubricating etc complete, without door 75mm

Providing and fixing R.P.V.C. vent cowl: 110mm

Providing and fixing R.P.V.C. vent cowl: 75mm

Construction of manhole rectangular in shape including cement concrete 1:3:6 (1 cement:3 coarse sand:6 graded stone aggregate 20mm nominal size) foundation thickness of concrete 20cms and offset 10cms on both sides and first class brick work with bricks class designation 100kg/cm2 in cement mortar 1:3 (1 cement : 3 coarse sand) 23cms thick including providing & fixing CI footrests confirming to IS 5445/69 or revised and whose weight shall not be less than 5.30kgs including fixing in man-hole at 30cm c / c in 20x 20x10cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) and 12mm thick plaster inside and outside with cement mortar 1:3 (1 cement : 3 coarse sand) including adding waterproofing compound of approved brand in cement mortar with a floating coat of neat cement and making channel in cement concrete 1:2:4 (1 cement :2 coarse sand : 4 graded stone aggregate 20m nominal size) neatly finished complete as per standard design. Inside size 0.60x0.60m and 0.60m deep (with medium duty DI manhole cover & frame of size 0.60x 0.60m weighing 90kgs ) including fixing with cement concrete 1:2:4 ( 1 cement :2 coarse sand : 4 graded stone aggregate 20mm nominal size and applying the frame & cover with coal tar.

Providing and fixing square mouth S.W. Gully trap grade “A” complete with C.I. Grating brick masonry chamber and water tight C.I. Cover with frame of 300 x 300 mm size (Inside the weight of the cover to be not less than 4.53 kg.) And frame to be not less than 2.72 kg as per standard design:. b) 150 x 100 mm size P or S type

Providing and fixing ASTM UPVC pipe, conforming to ASTM 2467 with ISO 14001, including all UPVC plain & brass threaded fittings, including jointing of pipes & fittings with one step UPVC solvent cement, trenching ,refilling & testing of joints complete as per direction of Engineer. External work. SCH-80(blue)/(white) 25mm outer dia.

Providing and fixing ASTM UPVC pipe, conforming to ASTM 2467 with ISO 14001, including all UPVC plain & brass threaded fittings, including jointing of pipes & fittings with one step UPVC solvent cement, trenching ,refilling & testing of joints complete as per direction of Engineer. External work. SCH-80(blue)/(white) 32mm outer dia.

Providing and fixing brass full way valve (heavy) duty with wheel of approved quality : (Toilet internal Ball valve 15mm nominal bore

Providing and fixing brass full way valve (heavy) duty with wheel of approved quality : (Toilet internal Ball valve 40 mm nominal bore .

Providing and fixing non-return valve of approved quality : 40 mm nominal bore

Providing and fixing ball valve ( brass ) of approved quality Low pressure with copper floats 25 mm nominal bore

Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes confirming to IS:15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 mt. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer-in-charge. Internal work exposed on wall (Medium duty SDR 13.5 15 mm

Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes confirming to IS:15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 mt. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer-in-charge. Internal work exposed on wall (Medium duty SDR 13.5 20 mm

Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes confirming to IS:15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 mt. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer-in-charge. Internal work exposed on wall (Medium duty SDR 13.5 25 mm

Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes confirming to IS:15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 mt. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer-in-charge. Internal work exposed on wall (Medium duty SDR 13.5 32 mm

Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes confirming to IS:15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 mt. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer-in-charge. Internal work exposed on wall (Medium duty SDR 13.5 40 mm

Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes confirming to IS:15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 mt. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer-in-charge. Internal work exposed on wall (Medium duty SDR 13.5 50 mm

Providing at store or site work non-pressure RCC pipes of with collar joints conforming to IS:458-2003 revised as per amendment No.11 , including freight, carting, loading, unloading, stacking etc. complete 150 mm

Conveying carefully from stack at site, 250m from both sides rolling and lowering into trenches, laying and jointing true to line and level, RCC spun pressure and non pressure pipes of various classes, specials including collar and perfect linking of joint with jack to correct position including cost of jointing material in cement mortar 1:2, necessary hydraulic testing, curing of cement mortar etc. complete. 150 mm

Providing and placing on terrace roof of floor two (1st flor roof single piece rotational moulded polythene water storage tank having I S I mark and conforming to I S 12701;1996. 1000 lit. capacity

Providing and fixing, Testing & Commissioning of Submersible Pumpset (WORKING +STAND BY) capacity 1 LPS & Head 15 m, Casing - CI (Corrosion Proof), Impeller - CI, Shaft - SS, Hardwares - Stainless Steel, Double mechanical seal, Common Wall Mounted Control Panel with Potential Free Contacts for both Pumps & all alarms along with all valve arrangement with vibration isolator factory assembled & tested for rated efficiency complete with TEFC motor EFF3 rating for working and stand by pumps

ELECTRICAL WORKS

Supply ,Installation,Testing & Commisioning 10 m high (clear height) galvanised octagonal pole with suitable arrangement for max. 4 nos. luminaries and with foundation bolts having bottom of 175 mm A/F, top 70 mm A/F on provided foundation, with all required accessories like Junction box with 15A Input output connectors , 16 A C curve SP MCB for suitable for each light fittings 3 CORE 1.5 Sq. mm Cu Felx. cable for light fitting from Junction box to Light fittings and its termination of cables should be made using with proper lugs etc.

Supplying and erecting LED flood light fitting of 200W,including lamp, with PF > 0.95,class IP 65 and above housing of pressure die cast aluminium alloy and heat sink extruded aluminium complete with all required accessories .

Supply ,Installation,Testing & Commisioning of 6 m high galvanised Decorative conical pole with Decorative Street light bracket for erection of Single fitting made from 40 mm. dia ‘B’ class G.I. pipe 1.0 m in length along with pole cap of 300 mm length 100 mm dia .(Suitable to pole top) duly welded and with foundation bolts having bottom dia. from 135 to 160 mm, top dia. from 65 to 75 mm on provided foundation, with all required accessories like Junction box with 15A Input output connectors , 0.5 - 6 A C curve SP MCB for suitable for each light fittings 3 Core 1.5 Sq. mm Cu Flex. cable for light fitting from Junction box to Light fittings and its termination of cables should be made using with proper lugs ,Pole will Be Painted with P U Paint as per GTDC color choice etc.

Supply ,Installation,Testing & Commisioning LED Street light fitting of 45W,including lamp, with PF > 0.95,class IP 65 and above Housing of pressure die cast aluminium alloy and heat sink extruded aluminium Complete with all required accessories .Efficacy >100lm/W.

Supply ,Installation,Testing & Commisioning of Step Light with 3W LED lamp Die-cast aluminium IP Rating : IP 65 complete with all accessories, driver / power supply (if any), connecting wire, including gear box and junction box for cable connection connection Complete with all required accessories and Coated with epoxy zinc phosphate primer and finished using environmentally stable polyurethane based paint .

Supply of 3 core armoured PVC/XLPE insulated, PVC sheathed copper conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. a)3 Core 2.5 sq.mm

Supply of 4 core armoured PVC/XLPE insulated, PVC sheathed copper conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. a) 4 Core 4 sq.mm

Supply of 3 1/2 core armoured PVC/XLPE insulated, PVC sheathed aluminium conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. a)3 1/2 Core 35 sq.mm

Supply of 3 core armoured PVC/XLPE insulated, PVC sheathed aluminium conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. 3 Core 16 sq.mm

Supply of 4 core armoured PVC/XLPE insulated, PVC sheathed aluminium conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. a) 4 Core 16 sq.mm

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size not exceeding 25 sq.mm in the existing RCC/HUME/STONEWARE Metal pipe, etc. complete as required

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size not exceeding 25 sq.mm direct in ground including excavation in the form of a trench as per Cable Trench Drawing provided by the Engineer-Incharge,sand cushioning with screened sand bed of 20mm thick , protective covering with bricks placed breadth-wise on top of cable all over the run( the brick protection shall cover the cable and project atleast 5 cms over the sides of the cable) and backfilling the excavated earth without stones or hard material and making the surface proper with 15 cm crown on the top complete as required. a) In soily strata

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size exceeding 25 sq.mm but not exceeding 120 sq.mm direct in ground including excavation in the form of a trench as per Cable Trench Drawing provided by the Engineer-Incharge,sand cushioning with screened sand bed of 20mm thick , protective covering with bricks placed breadth-wise on top of cable all over the run( the brick protection shall cover the cable and project atleast 5 cms over the sides of the cable) and backfilling the excavated earth without stones or hard material and making the surface proper with 15 cm crown on the top complete as required. (a) In soily strata

Laying of one number additional PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size not exceeding 25 sq.mm direct in ground in the same trench in one tier horizontal formation including excavation in the form of a trench as per Cable Trench Drawing provided by the Engineer-Incharge,sand cushioning with screened sand bed of 20mm thick , protective covering with bricks placed breadth-wise on top of cable all over the run( the brick protection shall cover the cable and project atleast 5 cms over the sides of the cable) and backfilling the excavated earth without stones or hard material and making the surface proper with 15 cm crown on the top complete as required. a) In soily strata

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size not exceeding 25 sq.mm on surface, etc. complete as required

Supplying and making cable end terminations with brass compression gland and copper lugs for folowing sizes of 3 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. (1) 3 x 1.5/2.5 Sq. mm.

Supplying and making cable end terminations with brass compression gland and copper lugs for folowing sizes of 4 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. (a) 4 x 4 Sq. mm.

Supplying and making cable end terminations with brass compression gland and aluminium lugs for folowing sizes of 3 1/2 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. (a) 3 1/2 x 35 Sq. mm.

Supplying and making cable end terminations with brass compression gland and aluminium lugs for folowing sizes of 3 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. (5) 3 x 16 Sq. mm.

Supplying and making cable end terminations with brass compression gland and aluminium lugs for folowing sizes of 4 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. (a) 4 x 16 Sq. mm.

Construction of manhole rectangular in shape including cement concrete 1:3:6 (1 cement:3 coarse sand:6 graded stone aggregate 20mm nominal size) foundation thickness of concrete 20cms and offset 10cms on both sides and first class brick work with bricks class designation 100kg/sq.cm (wire cut bricks) cement mortar 1:3 (1 cement : 3 coarse sand) 23cms thick including providing & fixing CI footrests confirming to IS 5445/69 or revised and whose weight shall not be less than 5.30kgs including fixing in man-hole at 30cmc / c in 20x 20x10cm cement concrete block 1:3:6 (1 cement :3 coarse sand : 6 graded stone aggregate 20mm nominal size) and 12mm thick plaster inside and outside with cement mortar1:3 (1 cement : 3 coarse sand) including adding waterproofing compound of approved brand in cement mortar with a floating coat of neat cement and making channel in cement concrete 1:2:4 (1 cement :2 coarse sand : 4 graded stone aggregate 20m nominal size) neatly finished complete as per standard design.III) Inside size 0.60x0.60m and 0.60m deep (with medium duty DI manhole cover & frame of size 0.60x 0.60m weighing 90kgs ) including fixing with cement concrete 1:2:4 ( 1cement :2 coarse sand : 4 graded stone aggregate 20mm nominal size and applying the frame & cover with coal tar.(Refer Quantity in drawings)

Providing at store or site work non-pressure RCC pipes of with collar joints conforming to IS:458-2003 revised as per amendment No.11 , including freight, carting,loading, unloading, stacking etc. complete. b) 100 mm Dia.NP2 Class

Supplying and fixing following way SPN sheet steel MCB distribution board Consumer Unit 240 V on surface/ recess complete with tinned copper busbar neutral busbar earth bar dinnbar hinged front acrylic cover for the MCB knobs detachable gland plate interconnections phosphotized and powder painted including earthing etc. as required ( but without MCB/RCCB/Isolator)(a) 2 + 4 way Cat A

Supplying and fixing 6 A to 32 A, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required. a) SP, Cat A

Supplying and fixing 6 A to 32 A, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required. b) DP, Cat A

SITC of Cable Junction Boxes IP 66/67 “weather proof”(Size -155 x 210 x 92 (LXBXH)mm), for outdoor installation(with knockouts for cable entry) with all accessories.

Earthing with GI earth pipe 2 mts long 40 mm dia medium class with ISI mark, of approved brands including accessories and providing masonry enclosure with CI/RCC cover having locking /Lifting arrangement and watering pipe etc. (but without charcoal or coke and salt) as required as per the Earthing Drawing provided by the Engineer-Incharge.The scope of work includes the following: a) Excavation of pit of size not less than 1.0x1.0x 2.0 mtrs(min) and disposal of excavated soil. b) Class B GI pipe, 40mm diameter as per specifications. c) Charcoal/salt as per specs ( paid seperately). d) Refilling the pit of size not less than 1.0x1.0x 2.0 mtrs(min) with soft black soil of minimum resistivity i/c transportation. e)Masonary chamber with proper foundation, cover plate and locking arrangement. f) Testing of earth value with earth megger and certifications of its value. Aluminium tag with embossed earthing value to be attached to the pipe . g)watering arrangement(plumbing will be paid seperately). (b) In rocky strata

Earthing with GI earth plate 600 mm x 600 mm x 6 mm thick including accessories and providing masonry enclosure with CI/RCC cover having locking/Lifting arrangement and watering pipe etc. (but without charcoal or coke and salt) as required as per the Earthing Drawing provided by the Engineer-Incharge.The scope of work includes the following: a) Excavation of pit of size 1.0x1.0x 3.0 mtrs(min) and disposal of excavated soil. c)Watering GI pipe, 20mm, Class B, with funnel as per specs. d) Charcoal/salt as per specs ( paid seperately). e) Refilling the pit of size 1.0x1.0x 3.0 mtrs(min) with soft black agriculture soil of minimum resistivity i/c transportation. e)Masonary chamber with proper foundation, cover plate and locking arrangement. f) Testing of earth value with earth megger and certifications of its value. Aluminium tag with embossed earthing value to be attached to the pipe.g)watering arrangement(plumbing will be paid seperately). b)In rocky strata

Extra for using salt and charcoal for pipe earth electrode as required( 65 Kgs of Charcoal and 5 Kgs of Salt).

Supplying and laying 25 mm x 6 mm GI strip at 0.5 m below ground as strip earth electrode including soldering etc. as required

Supplying and laying 6 SWG GI wire at 0.5 m below ground level for conductor earth electrode including soldering etc. as required

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in recessed PVC conduit(heavy) with modular switch, modular plates, suitable size modular GI box of specified Category and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. a) Group B -- with Cat A Modular Accessories

Wiring for group controlled light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable (with)in recessed PVC conduit(heavy) and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable in the (with) independent recessed PVC conduit(heavy) of appropriate size as required. a) 2 x 2.5 sq.mm + 1 x 2.5 sq.mm earthwire (20mm Conduit)

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable in the (with) independent recessed PVC conduit(heavy) of appropriate size as required. (b) 2 x 4 sq.mm + 1 x 4 sq.mm earthwire (20mm Conduit)

Supplying and fixing of following sizes of rigid PVC conduit alongwith accessories in surface(medium)/recess(heavy) including cutting the wall and making good the same in case of recessed conduit as required. a) 25 mm

Supplying and fixing of following sizes of rigid PVC conduit alongwith accessories in surface(medium)/recess(heavy) including cutting the wall and making good the same in case of recessed conduit as required. b) 32 mm

Supplying and fixing following modular switch/ socket on the existing modular plate and switch box including connections but excluding modular plate etc. as required a) 5/6 A switch Cat A

Supplying and fixing following modular switch/ socket on the existing modular plate and switch box including connections but excluding modular plate etc. as required b) 3 pin 5/6 A socket outlet Cat A

Supplying and fixing following modular switch/ socket on the existing modular plate and switch box including connections but excluding modular plate etc. as required c) 15/16 A switch Cat A

Supplying and fixing following modular switch/ socket on the existing modular plate and switch box including connections but excluding modular plate etc. as required d) 6 pin 15/16 A socket outlet Cat A

Supplying and fixing modular blanking plate on the existing modular plate switch box excluding modular plate etc. as required a) Cat A

Supplying and fixing following size modular GI box alongwith modular base and cover plate for modulator switches in recess etc. as required a) 1 or 2 Module ( 75 mm x 75 mm) Cat A

Supplying and fixing following size modular GI box alongwith modular base and cover plate for modulator switches in recess etc. as required b) 4 Module ( 125 mm x 7 mm) Cat A

Supplying and fixing following size modular GI box alongwith modular base and cover plate for modulator switches in recess etc. as required (c) 6 Module (200mm x 75 mm) Cat A

Supplying and erecting LED Light with integrated driver including 8W lamp with having pressure die-cast aluminium housing, opal translucent cover, mounting arrangement with board for surface type or spring loaded mounting clips for flush type complete.

Supplying and erecting LED Light with integrated driver including 12W to 15W lamp with having pressure die-cast aluminium housing, opal translucent cover, mounting arrangement with board for surface type or spring loaded mounting clips for flush type complete.

Supplying and erecting outdoor type decorative oval bulk head edge-lit 10W LED luminaire comprising of high brightness LED Fitting on provided PVC block / wooden board.

Supply and erecting of 12 inch (300 mm sweep) exhaust fan with double ball bearings, 1400 rpm, complete with all accessories. (a) Cat A

Supplying & erecting LED 20W tube light fitting (4 feet) with aluminium housing, heat sink, integrated HF electronic driver complete.

Supply and erecting of 48 inch ( 1200mm sweep) ceiling fan, double ball bearing type, , complete with all accessories. (b) Cat B

Supply and erecting fan hook box ( 100 mm diameter or equivalent square size, 75mm deep) fabricated out of 16 SWG sheet steel with 10 m round bar hook bounded to RCC steel upto 50 mm length protruding on each side of the box, including painting with 2 coats of red oxide, complete as required.

Allabaksh Mulla