Capital Grant Fund Scheme 2024-2025

Amount

Earthwork excavation for foundation in all soils and sub soils in hard stiff clay, stiff black cotton, hard red earth, shales, murram, gravel, stoney earth and earth mixed with small size boulders and to full depth as may be directed,except in hard rock,requiring blasting including shoring and shuttering and bailing out of water wherever necessary,refilling the sides of foundation with excavated earth or sand in layer of not more than 15cm thick.well rammed and consolidated and depositing on bank with initial lead and lift of 10m & initial lift of 2m and depositing the surplusr earth within the compound in places shown by the departmental officers with iniital lead and lifts,clearing and levelling the site etc., complete as per SS20B and as directed by departmental Engineers(TNBP No.17,23,24).

Plain Cement Concrete 1:4:8 mix (One Cement, Four Fine Aggregate Crushed Stone Sand and Eight Coarse Aggregate) Using 40mm ISS HBG metal for foundation and basement including dewatering if found necessary and laid in layer of not more than 15cm thick and consolidated including all cost conveyance of materials and labour charges etc. complete as per standard specifications and as directed by departmental Engineers(TNDSS No.28).

Supplying and erecting centering for sides and soffits including supports and strutting uptp 3.29m height for plane surfaces in all floors with all cross bracings using mild steel sheets of size 90cmx60cm and 10 gauge stiffened, welded with mild steel angles of size 25mmx25x3mm for boarding laid over silver oak (country wood) joist of size 10cmx6.5cm dia spaced about 90cm centre to centre and supported by casuarina props of 10cm to 13cm dia spaced at 75cm centre tocentre etc.complete complying with standard specification and as directed by the departmental engineers. TNBP No.30

A) Column

B) Grade beam

C) Lintel. Beam &slab

Supplying, fabricating and placing in position mild steel or TMT rods for all reinforced cement concrete works as per design given including cost of steel and binding wire with all conveyance and lead charges in all floors etc.complete complying with standard specifications and as directed by the deparmental engineers. TNBP No:30

Providing and laying in position Standardised Concrete Mix M-25 Grade in accordance with IS 456 - 2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement contenet of 350Kg/ cum and maximum water cement ratio of 0.55 including admixture (Plasticiser / super plasticiser) in recommended proportions as per IS 9103 to accelerate, related setting of concrete, improve workability without imparing strength and durability with about (5.0cum), 7730Kg of 20mm machine crushed stone jelly and with about (3.3 cum), 5156kg of 10 - 12mm machine crushed stone jelly and with about (4.79cum) 7670 kg of Crushed Stone sand (M- Sand) but excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers - The Coarse and Fine aggregates to be used should comply with the requiremnents of IS standards.

Upto Basement

Ground floor

First Floor

Brick Work in CM 1:5 (One part of cement & five parts of sand) mix using Third Class Country Brick Kiln Burnt bricks 8 ¾ " x 4 ¼ " x 2 ¾" including cost and conveyance of materials to work site and including all labour charges for mixing, laying, curing the concrete etc., complete as per standard specifications and as directed by departmental Engineers – TNBP No:31

a) Upto Basement

b) Ground Floor

c) First Floor

c) Second Floor

Supplying and Filing in foundation and basement with Filling Well Gravel in layers of well rammed,watered consolidated including cost and conveyance of materials and labour charges etc., complete as per Standard Specification and as directed by departmental Engineers(TNBP No.24&25).

Special Ceiling Plastering with CM 1:3 (One part of cement & three parts of sand)mix for 10mm thick including cost and conveyance of materials to work site and including all labour charges for mixing, laying, curing,finishing etc., complete as per standard specifications and as directed by departmental Engineers – TNBP No:30,56&57

Plastering with CM 1:5 (One part of cement & five parts of sand) mix for 12mm thick including cost and conveyance of all materials to work site and including all labour charges for mixing, laying, curing,finishing etc., complete as per standard specifications and as directed by departmental Engineers – TNBP No:56&57

Plastering in Cement Mortor 1:5 Mix (one part of cement and five part of sand) 20mm thick including cost and conveyance of all materials to site, loading and unloading charges and labour charges for mixing, laying and curing etc. complete. Complying with std. specifications.

Supply and Fixing of Teak wood scantling wrought and put up for frames of door and windows including fixing holdfast and all labour charges and conveyance of all materials to site etc., Complete as per standard specification.

Supply and fixing of Teak wood fully panelled and Double leaf (two Equal Panels) shutter for door including all labour charges cost and conveyance of all materials to site etc., Complete as per standard specification.

Supply and Fixing of U-PVC Shutter openable Door using GI Steel Reinforcement, Butt hinge,Aldrop lock and foam Sheet including cost and conveyance of all labour and all meterial charges etc Complete as per standard specification.

Supplying and fixing M.S.grill to doors, special windows and ventilators etc as directed by the departmental officers inclusive of cost of MS grill including one of cost red oxide and fixing in position etc., complete (as per the schedule of rate) SL.NO.182 Q3

Supply and fixing of U-PVC Two shuter openable Window using G.I steel Reinforcement, friction hinge, multipoint lock, and 5mm clear glass or foam sheet including cost and conveyance of all labour and all meterial charges etc Complete as per standard specification.

Supply and fixing of U-PVC Fixed Louvers type Ventilator using GI Steel Reinforcement and 4mm Pinhead glass including cost and conveyance of all labour and all meterial charges etc Complete as per standard specification.

Supplying and fixing in Position of indian type water closet with all set in brick jelly concrete 1:4:8 Mix concrete 10 cm thick using 20mm brick jelly and top finished with c.m. 1:3 mix 20mm thick without any leakage etc. Complete as per standard specification.

Supplying and fixing in Position of Europeon type water closet with all set in brick jelly concrete 1:4:8 Mix concrete 10 cm thick using 20mm brick jelly and top finished with c.m. 1:3 mix 20mm thick without any leakage etc. complete.

Daddoing with first quality colour glazed tiles of 150 mm x 150 mm x 6mm size of approved make and quality and colour set in Cement Mortar 1:2 (One Cement and Two Sand) and pointing with white cement neatly including cost and conveyance of all materials etc.and all lobour charges etc.complete as per Standard specification and as directed by the departmental officers.TNBP No:special

Paving the floor with best quality Vetrified Tiles of size 600 x 600 x 8mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)m thick and pointing with white cement including finishing jointing and polishing with glossy finish etc complete as per std specification

Supplying and fixing over the floors best quality of scratch Ceramic tiles of 30 c.m x 30c.m x 6mm size of approved colour laying with cement mortor 1:3 mix pointing the joints with colour pigments etc. Complete.

Weathering Course concrete using best quality broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) near the RCC roof slab in the properties of brick jelly to lime being 12:12-1/2 by volume and laid over in single layer and consolidated to the required designs and finished thickness, beating the concrete with wooden beaters of approved pattern, keeping the surface constantly watted by sprinking lime jaggary water.

Finishing with top of roof with one course of machine pressed tiles of size 20cmx20cmx20cm of approved quality laid in cement mortar 1:3 (One cement and three sand) 12mm thick mixed with water proofing compound conforming to ISS by 2% weight of cement used and the joint pointed neatly to full depth of tiles with same water proofing compound mixed with cement motar ,red oxide, etc.complete complying with standard specification as directed by the departmental officers. TNBP No:44-I

Paving the floor with pre-polished concrete anti-skid tiles (Required shape and design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Painting new wood work with two finishing coats of synthetic enamel ready mixed paint of approved quality and colour over one coat priming coat in all floors including the cost of primer etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over one coat of red oxide priming coat in all floors including cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Plain Cement Concrete 1:2:4 Mix (one part cement, Two part M sand and Four part of aggrigate) using 20 mm size ISS HBG metal from approved quarry including cost and conveyance of all materials to site. Loading and unloading charges and labour charges for mixing. Laying and curing etc., complete as per TNDSS NO: 28 & VI (S2) VI (S5A) VII standard specifications as directed by Engineer incharge.

Providing and laying, spreading and compacting graded stone aggregates to Wet Mix Macadam 250mm thick specification including premixing the materials with water at OMC in mechnanical mix plant carriage of mixed material by tipper to site laying in uniform layers with pavers in Sub Base/ Base course on well prepared surface and compacting with vibratory roller to acheive the desired density including cost of material, labour charges, rentals for machinery, fuel and all other incidental charges etc., complete as per clause 406 of MORTH

Supplying and laying Precast Designer Paver Block confirming to IS 1568-2006 specification manufacturing and laying standard of M50 grade 80mm thick (table clauses 5 and 9.14) suitable for bus terminals industrial complexes road on expensive soils etc., including the cost of paver block of size 225mm x 12.50 mm x 80mm and conveyance of materials to work site mentioned in the tender schedule cost of loading and unloading handling during over Stone dust of 100mm thick (excluding the cost of sand) conveyance paver block cutter to site and hire charges of vibrators and block cutter operator and labour for leveling the sand to paver block etc., complete ISI 15658-2006.

Wiring with 2X1.5 sqmm (22/0.3) PVC insulated sc unsheathed Cu.conductor cable of 1100 V grade in suitable heavy gauge MS conduit pipe concealed in wall and ceiling with MS accessories with switch box with 5A F.T. switch(two way) in flush with wall and convered with 3mm thick hylem sheet for MS switch box with continous earth wire connection of 14 SWGTC wire and making good of the concealed portion with suitable colour for concealed stair case light point/Fan Point (SD.NO.24) Page No -13

Wiring with 2x1.5sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100 V grade in suitable PVCrigid pipe concealed in wall and ceiling with PVC accessories, in flush with wall, with 150mm x 100mm x 113mmTW switch box with 3 mm thick Hylem sheet cover for 5 A 3 pin non inter locking CS Plug with continuous earthwire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealedPVC plug point (SD 38)

Supply and fixing of TNEB meter board suitable for 32 A three phase service connection with3 nos of 32A fuse unit (500 V) 32A neutral link and earth link (1"X18" copper flat) on TW plant of size 600mm X 450mm X19 with supporiting TW reepers of 1 " thick an either side withpainting with suitable bolt and nuts for fixing the TW plank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit (SD No.127) Page No -59

Supply and run of 4 of 6 sqmm (84/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade in 32mm G.I pipe (Class 'B' bent at both ends with necessary angle iron up right and end supports for mains (SD No.73) Page No -33

Supply and run of 4 of 6 sqmm (84/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade on7/20 GI bearer wire for service connection mains (SD No.68)

Supplying and Fixing A.C Ceiling fan complete 1200mm (48”) sweep with 300mm Down Rod , with regulator ( Crompton make ) including cost and conveyance charges fixing and its position etc complete SD 106 ISI make with standard specification.

Wiring with 2x4 sqmm(56/0.3) PVC insulated SC unsheathed Cu.Conductor cable of 1100V grade in suitable heavy gauge MS conduit pipe concealed In wall and ceiling with M.S.accessories in flush with wall with 150mm x100mm x 75mm MS switch box concealed type with 3mm thick hylum sheet cover for 15A 3 pin flush type noninterlocking C.S.plug with continuous earth wire connection of 14SWG TC wire and rnaking good of the concealedportion with suitable colour for concealed power plug point SD 15

Supply and fixing of WT bulk head fitting with guard (Philips / Bajaj / Crompton / K. Lite) suitable for11W CFL lamp with CFL. SD 83

Supply and fixing of single box type 4'40 W flu fitting complete with copper choke and condensor with TW round blocks on wall or ceiling with flu tube with PVC unsheathed Copper leads from terminals to the fitting. SD 88

Supply and delivery of 1000 litre capacity H.D.P.E.Water tank approved ISI Quality including cost and convenance of all materils to the site etc complete As per standard specification

Supply and Filling of 40 mm HBG ISS Metal from approved quarry including cost and conveyance of all materials to site, loading and unloading charges and filling to required depth etc., Complete as per standard Specification

Supply and delivery of following PVC Pipes 110mm PVC Pipe 6kg/cm2 including cost and conveyance of materials to site etc complete,.

Supply and Filling of 40 mm Brick Jelly from approved quarry including cost and conveyance of all materials to site, loading and unloading charges and filling to required depth etc., Complete as per standard Specification