SPECIAL REPAIR TO BLDG NO H1 (OLD MI ROOM) OF RMS AND TRG SHED IN FRONT OF BLDG NO P-39 AT AJMER MIL STN

Amount

Demolition of cement concrete (unreinforced) in ground floor and pavings not exceeding 15cm thickness below or above ground level and removing material from site complete all as specified and directed.

Taking down chowkhat or frames with shutter (without taking off shutter from the frame ) area n.exc 1.5 Sqm each complete with hold fasts etc and making good disturbed surface of walls in cement mortar (1:3) complete all as specified and directed

Taking down chowkhat or frames with shutter (without taking off shutter from the frame ) area exc 1.5 Sqm but n. exc 4.0 Sqm each complete with hold fasts etc and making good disturbed surfaces of wall in CM (1:3) complete all as specified and directed

M&L for non skid ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.11 Sqm but not exc 0.18 Sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bedding in cement mortar 1:6, complete all as specified and directed.

M&L for machine cut kota sotne slab, 20-25mm thick over and including 15mm thick screed bedding in cement mortar 1:6 as in floors, laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing with mirror polish complete all as specified and directed.

M&L for machine cut kota sotne slab in verticle/ skirting / steps / risers of reqd size, 18 to 20mm thick & including 15mm thick screed bedding in cement mortar 1:4 as laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing with mirror polish complete all as specified and directed.

M&L for vitrified ceramic tiles light shade 8-10mm thick (square / rectangular ) polished, area of each tiles exc 0.18 Sqm but not exceeding 0.36 Sqm, in floor/skirting/dado etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed 15mm thick in CM 1:6 complete all as specified and directed.

M&L for 16-18mm thick granite (of any type Jet/Telephonic Black) work (table rubbed and polished) in steps, jambs, pillars, window -cills, cooking platforms, counter basins, urinal partitions etc and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite incl rounding of edge laid over 15mm thick screed bed in CM (1:6) including rounding of edges of stone slabs one edge, coloured cement to match the surfaces and half nose moulding (bull nosing) etc,complete all as specified and directed.

M & L for 75 mm thick Cement concrete 1:3:6, type C-1 (using 20mm graded stone aggregate) as in plinth protection with fair finished surface complete. Note : Joints 12mm wide to the full depth of PCC shall be provided at every 3 meters and at every change of direction and shall be filled with mixture of bitumen and sand 1:3 by weight. Cost of this provision shall be deemed to be included in the quoted rate for concrete in plinth protection.

M&L PCC (1:4:8) Type D-2 using 40 mm graded stone aggregate in foundation, filling and sub base surface finished even & fair complete all as specified and directed.

M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 grade with grey cement and pigment coloured, reflective type of approved quality and vibrated with mechanical vibrator & including 50 mm thick sand cushioning, joints of blocks filled with dry sand and compacted with mechanical vibrator complete all as specified & directed.

M&L for Vitrified out door tiles 40 cm x 40 cm x 10-12 mm thick digital design set, jointed and pointed in neat cement slurry as in floors with grey cement over & including over screed bed or bedding layer of mortar 20 mm thick Cement Mortar 1:6 complete all as specified & directed.

M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in cill , steps, parapets and railing upto 60cm in height , coping, kneelers, apex stones, bed plates, and the like including weathering, slightly rounded or chamfered angles and throating as directed complete all as specified and directed.

M& L for modern design elevation tiles in vertical surfaces of exreme face of columns, facades etc of sizes 300 x 450 x 7-8mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick cement plaster in Cement mortar 1:4 as backing coat on fair faces on stone surface all as specified and directed.

Dismantling Asbestos cement (corrugated of semicorrugated etc), any gauge, thickness, roof coverings complete all as specified as directed.

S & F pre-painted galvalume aluminum zinc coating(AZ-150) GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws/ Lor J type hook complete all as specified & directed.

S & F for pre-painted galvalume aluminum zinc coating (AZ-150) GI based Profile steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws/ Lor J type hook complete all as specified & directed.

M & L for Coloured double charged vitrified tiles in vertical surface 300x 450x 7-8 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick cement plaster in Cement mortar 1:4 as backing coat on fair faces on stone surface complete all as specified and directed.

Dismantling unframed timber fillets, rails, posts, rafters, purlins etc under 40 sqcm in section complete all as specified as directed.

S & F steel work in tublar truss including special shaped washer etc. complete using ERW or induction butt welded tubes confirming to IS 1161-1979 grade st 240 etc confirming to fe-410-W (Gde-E-250) quality-A, including complete fittings all as specified as directed.

Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets, complete all as specified as directed.

S&F false ceiling with fibre Cement Designer tile Ivory painted (High Pressure Steam Cured) of 4mm thickness (as per IS:14862) of size 595x595 mm and any one of the design (oceanic, lake & hill, cascade or electra) in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 gms, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and 15x32 mm made from 0.30 mm thick sheet, spaced at 1200 mm c/c and cross "T" of size 15x32 mm made of 0.30 mm sheet, 1200mm long spaced between main "T" at 600 mm c/c to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size15x32 mm made of 0.30 mm thick sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 15x20 mm made of 0.30 mm thick sheet and laying false ceiling tiles in the grid including , required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI soffit cleats fixed to existing RCC lintel with dash fasteners, GI adjustable rods of 3mm dia with galvanised Butterfly level clips, spaced at 1200 mm c/c along main T, bottom exposed width of 15mm of all T -sections shall be centra black pre-painted with polyester paint, and having a load bearing capacity of 12 kg/sqm, all complete at all heights complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specially provided for including cutting of steel reinforcement as required to facilitate demolition, complete all as specified.

M&L for providing RCC, 1:2 :4 type B1 using (20mm graded stone aggregate ) as in cooking platform, beam, cantilevers and kitchen cooking platform including necessary formwork complete all as specified.

M & L for repair to RCC (1:2:4) type B-1 using 20 mm graded stone aggregate as in chajjas/roof slab etc including necessary formwork complete all as specified and directed.

M & L for repair to RCC (1:2:4) type B-1 using 20 mm graded stone aggregate as in columns/ footing/ pier etc work including necessary formwork complete all as specified and directed.

M & L for mild steel TMT bars of 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed by the Engineer-in-Charge.

M&L for TMT bars of 6 to 8mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed ) not less than 0.9 mm dia complete all as specified and directed.

S&F made 100% Solid WPC (Wood Polymer Composite) Door Frames of cross section 65 mm x 125 mm (moulded) having single rebated made from Wood Polymer Composite (Single Extruded Process) material comprising of virgin PVC polymer of K-Value 57-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ruce husk/wheat husk)and non toxic additives fabricated with meter joints after applying PVC solvent cement & screwed with full body treated star headed screws having minimum frame density of 780 Kg/cbm & manufactured by "Rajshri/Echon or Eq" an ISO 9001-2015 certified company, having good screw holding capacity (Screw withdrawal strength of (Min, 990N) Minimum compressive strength of 58 N/mm2, modulus of elasticity 900N/mm2 and resistance to spread of flame of class A category with property of being termite/borer prof, water/moisture proof & fire retardant & fixed in position with and including SS Dsh Fasteners/Hold Fast of required dia and length, all as per specifications drawings as directed,. Material test certificate and authentication should be compoulsory provided by the manufacturing company complete all as specified and directed.

S&F for 2nd class hard wood 30mm thick Plain, framed, panelled shutters (03 number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as per specified and directed.

S & F 35mm thick 2nd class HW glazed and skeleton shutters open rebated and prepared to receive glass/wire cloth gauge etc, (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutters as specified in SSR part I, sectiion 8, clause 8.24(a) Member shall be kiln seasoned as per IS-1141 & chemically pressure treated as per IS-401 complete all as specified and directed.

S&F made 100% Solid WPC (Wood Polymer Composite) Door Frames of cross section 45 mm x 70 mm (moulded) having single rebated made from Wood Polymer Composite (Single Extruded Process) material comprising of virgin PVC polymer of K-Value 57-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ruce husk/wheat husk)and non toxic additives fabricated with meter joints after applying PVC solvent cement & screwed with full body treated star headed screws having minimum frame density of 780 Kg/cbm & manufactured by "Rajshri/Echon or Eq" an ISO 9001-2015 certified company, having good screw holding capacity (Screw withdrawal strength of (Min, 990N) Minimum compressive strength of 58 N/mm2, modulus of elasticity 900N/mm2 and resistance to spread of flame of class A category with property of being termite/borer prof, water/moisture proof & fire retardant & fixed in position with and including SS Dsh Fasteners/Hold Fast of required dia and length, all as per specifications drawings as directed,. Material test certificate and authentication should be compoulsory provided by the manufacturing company complete all as per specified and directed.

S&F factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N / m2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fie retardant WPC to be laminated with PVC foil of minimum 14 micron thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, Complete all as per direction of Engr-in-Charge. (Note : Stainless steel butt hinges and necessary SS screws shall be paid separately).

S&F factory made Steel window/ ventilator glazed & gauged (combination) with side hung/ top hung shutters incl box type / projecting type hinges, and steel peg stay, handle & locking arrangement and frame made out of 1.25mm thick pressed steel frame complete incl necessary cooler arrangement in window & guard bars all as shown in drg No. CEBZ/TD/14/11 sh No 1/7 to 7/7 & specified. (Make: M/S Jangid and equivalent).

S&F 3.00mm thick sheet glass, ordinary quality, 3mm thick fixed with oil putty size of glass not exc 0.50 sqm in each pane, complete all as specified and directed.

S&F 200 mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F 150mm long, 10mm dia extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F mild steel butt hinges, medium weight, cold rolled, ISI marked of size 100 mm including necessary welding work etc complete all as specified and directed.

S&F 300mm long alumimium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolt and sliding bolt of extruded section or cast aluminium alloy all as specified and directed.

S&F double legged door stopper of overall length of cover plate 150 mm of aluminium alloy body and tongue anodised with hard drawn steel spring fixed in floors and rubber confirming to IS complete all as specified and directed by Engr-in-charge.

S&F in repairs aluminium Hat and coat hooks, solid body, 175mm to 250 mm including all fittings confirming to IS complete all as specified and directed by Engr-in-charge.

S&F MS helical door spring 150mm long fixed with screws to wooden chowkhats or fixed with welding to steel chowkhats confirming to IS complete all as specified and directed by Engr-in-charge.

S&F wire netting of stainless steel wire1.4mm dia (size of mesh 12mm) fixed with tinned tacks of stainless steel wire staples or fixing with beads to wooden joinery when fixed in panels of joinery, complete all as specified and directed.

S & F in repair powder coated aluminium door shutters with frame of aluminium section including necessary joining cleats, glazing clips, rubber neoprene packing, brass handle and brass tower bolts of size 150mm x 02 Nos in each door, hinges, anodised aluminium snap beading screws, hydraulically regulated double action floor door spring made up of 1.25mm thick aluminium alloy sheet foundation box for each shutter, etc and including fitted with brass mortice lock 100mm 2 levers, vertical type complete all as specified and directed.

S & F in repair powder coated aluminium window/ventilator shutter with frame, sliding/side hung type with sash bars including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc and incl each window fitted with 5 mm thick tinned glass in glazed shutter and including stainless wire cloth 0.36mm nominal dia and average width of aperture 1.40mm in gauzed shutter etc complete all complete all as specified and directed

Dismantling boarding, any description, fixed in any position with nails complete all as specified and directed.

Fabrication & fitting with cabinet / shelves & wardrobe / cupboard made out nof 18mm thick (one side decorative lamination & other side balancing lamination ) PVC sheet with piano hinges including providing cabinet for keeping baskets / cutlery basket with handles door shutters all as specified and directed. Note : PVC sheet, fittings & fixture will be measured and paid separately.

Supply only 18mm thick (one side decorative lamination & other side balancing lamination sheet) solid PVC board of all as specified and approved by Accepting Officer with cement solvent adhesive for shutter / kitchen cabinet / cup boards / partition wall / wall cabinet and similar work complete all as specified and directed. Make : Rajshree or equivalent

S&F in repair continous (Piano) hinges, mild steel, bright finish, width of flaps (when open) 30mm complete all as specified and directed.

S&F 125mm dia oval shape brass handle fancy type bright finish confirming to IS complete all as specified and directed.

S&F in magnetic ball catches with 8mm dia steel ball and brass body and striking plate including letting in and fixed complete all as specified and as directed by Engr-in-charge.

S&F for anodised aluminium grill of (anodised transparent or dyed to required shade according to IS:1868 with minomum anodic coating of grade AC 15) of approved design/ pattern, with approved standard section and fixed to the existing window frame with C.P. brass / stainless steel screws @ 200mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised alumiinium standard section around the opening, all complete all as specified and as directed by Engr-in-charge.

S&F 5.5mm thick plain/tinted sheet glass, ordinary quality and glazing rubber beading in square exc 0.5 sqm in each pane complete all as specified and as directed by Engr-in-charge.

S&F in stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed on wooden/steel frames with tinned tacks or stainless steel wire staple complete all as specified and directed.

S&F in repairs, 25mm dia stainless steel curtain rod heavy duty complete all as specified & directed.

S&F in repair decorative Curtain Finials/ knob & heavy Curtain Support Bracket for rod made of stainless steel, etc complete all as specified & directed.

S&F in repair of stainless steel decorative fincals(round type with mirror optic finish)trade pattern for decorative type curtain rods suitable for 22 to 25mm dia curtain rods as per sample as in repaie complete all as specified & directed.

Supply & fixing of stainless steel decorative fincals wall to wall trade pattern suitable for decorative type curtain rods 22 to 25mm dia as per sample as in repair complete all as specified & directed.

Demolition of brick or stone Masonary built in cement mortar etc laid dry below or above ground level and removing material from site complete all as specified and directed.

M&L for old size brick work with fly ash bricks, straight or curved on plan exc 6M mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for old size brick work with fly ash bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and directed.

Demolition of cement concrete (reinforced) jali/louvers of any description and in any position not otherwise specifically provided for, including taking complete all as specified and directed.

M&L for Providing precast cement concrete 1:2:4 (Type B1, (using 20mm graded aggregate)using 20mm graded aggregate) in window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings. kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, ancho-rage blocks, bonders (for stone wallin) corbels, brackets, etc. (of any section ndicated), with plain fair faces, including chamfers, weatherings, hroat- ing etc. and setting in mortar complete with joints to match Set in cement mortar 1:4 complete all as specified and as directed.

Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) of 200mm bore set in cement mortar complete all as specified.

Excavation in trenches not exceeding 1.5 metres wide and not exceeding 1.5 metres in depth for foundation or laying/taking out existing pipe etc and getting out in any type of soil, complete, all as specified and directed

M&L for lowering, laying, aligning & fixing in position and joining at all level/depths full round DWC (Double wall corrugated) of 200 mm dia bore with required jointing accessories of SN-8 garde as per IS-16098 (Part-2) amended upto date in trenches in complete including all material, labour, sectional hydrostating (incl the cost and conveyence of water to site for testing) and commissioning as per technical specifications, drawings and as per directions of Engr-in-Charge.

Removing excavated material exc. 250 m but n.exc 500 m from site and depositing where directed at a level n. exc 1.50mtr above the starting point complete all as specified and directed.

Returning, fillings in including spreading, levelling, watering and well ramming in layers, n.exc 25cm thick in soil complete all as specified and directed.

Taking down cement or cement lime plaster on stone/brick wall, ceiling incl. Raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for 15mm thick rendering in cement mortar (1:6) on brick/stone masonry or concrete surfaces (internal walls) of any description, finished the surface even and smooth without using extra cement complete all as specified.

M&L 15mm thick rendering in cement mortar (1:4) mixed with water proofing compound @ 3 % by weight of cement on other than fair faces of brick / stone masonary surfaces, finished even and smooth without using extra cement, complete all as specified and directed (WPC measured and paid separately) complete all as specified and directed.

M&L for rendering 10 mm thick in cement plaster 1:3 as in ceiling surfaces finished even and smooth (without using exta cement) complete all as specified & directed.

Supply only liquid water proofing compound of approved quality and make confirming to IS complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of interior emulsion plastic paint over a coat of 1mm thick birla white wall care/Asian wall/JK Cement wall max putty complete all as specified and directed. Make-Berger / Asian / Nerolac

M&L for applying two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed. Make-Berger / Asian / Nerolac

M&L for preparation of new plastered surface of ceiling and applying three coats of white wash complete all as specified.

M&L for preparation of old plastered or un-plastered surface including brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying two coats of interior emulsion distemper on walls over a coat of 1mm thick birla white wall care/Asian wall/JK Cement wall max putty complete all as specified and directed. Make-Berger/Asian/Nerolac

M&L for preparation of old plastered or un-plastered surface including brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applyingTwo or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and directed. Make-Berger/Asian/Nerolac

M & L for preparation of new wooden surface over 10cm width or girth and applying two coats of synthetic enamel paint of Ist quality over a coat of pink primer complete all as specified and directed.

M&L for preparation of new steel surface over 10cm width or grith & applying two coats of synthetic enamel paint of 1st quality over a coat of red oxide primer complete all as spd & directed.

Demolition and breaking up of rain water pipe /UPVC pipe line 100mm/75mm dia incl all fittings, complete all as specified.

S&F for 110mm dia UPVC, soil waste drain pipe, type ‘A’ , conforming to IS 13592-1992, single socketed, in any length with rubber rings joints or jointed with solvent cement joint, laid in floors or walls etc complete all as specified and directed. (Note- Rubber rings for pipes and fittings shall be conforming to IS 5382-1985)

S&F for 75 mm dia UPVC, soil waste drain pipe, type ‘A’ , conforming to IS 13592-1992, single socketed, in any length with rubber rings joints or jointed with solvent cement joint fixed to wall/floors etc complete all as specified and directed. (Note- Rubber rings for pipes and fittings shall be conforming to IS 5382-1985)

S&F for 110 mm bore UPVC (SWR) bend with access door including jointing with solvent cement, complete all as specified. (Note- UPVC bends shall be conforming to BS 4515 DIN 19531 and DIN 19534)

S&F 110 mm bore UPVC (SWR) ( singleT) equal or unequal including jointing with solvent cement, complete all as specified.

S&F 110 mm bore UPVC (SWR) branch piece, single ( singleY) equal or unequal including jointing with solvent cement, complete all as specified. .

S&F for 75 mm bore UPVC (SWR) bend including jointing with solvent cement, complete all as specified. (Note- UPVC bends shall be conforming to BS 4515 DIN 19531 and DIN 19534)

S&F PVC (SWR) 75 mm bore branch piece (Tee) fixed to walls with cement joint with oval access door complete all as specified and directed.

S&F PVC (SWR) 110 mm bore PVC (SWR) with vent cowl complete all as specified and directed.

S&F PVC (SWR) 75 mm bore PVC (SWR) vent cowl complete all as specified and directed.

M&L in repairs 75mm dia cast iron floor trap including jointing to waste pipe fixed in cement concrete type-B-1 (1:2:4) using 12.5mm brick aggregate all as specified and directed.

M&L in repairs PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement including jointing to waste pipe fixed in cement concrete type-B-1 (1:2:4) using 12.5mm brick aggregate all as specified and directed.

Dismantling of sand stone slab of any thickness laid bedded and pointed in any mortar complete all as specified and directed.

Taking down existing water proofing treatment of any description incl PCC padding, cement plaster any thickness from roof surfaces, cleaning of roof and prepairing it for further treatment incl make good necessary dubbing out wherever required and removing rubbish from site complete all as specified and directed.

M & L for screed plaster 10mm thick in CM (1:4) on fair faces of brick work or concrete surfaces mixed with WPC incl necessary doubingout etc finished even and smooth for laying WPT without using extra cement complete all as specified and directed.

M&L for coved fillet in PCC 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate at junction of roof & parapet wall and other vertical surfaces 75mm radius and surface painted with a hot paving bitumen grade 30/40 conforming to IS-73 @0.70 Kg/Sqm over a coat of bituminous primer conforming to IS-3384 @ 0.30 Ltr Sqm complete all as specified and directed.

M & L for APP modified polymeric water proofing membrane, 3mm thick having centre core not less than 100 micron high molecular high density polythylene film (HMHDPE) protected on both sides with high polymeric asphaltic mix and 20 micron HMHDPE film weight not less than 3.00Kg/Sqm applied with bonding material using blown type bitumen conforming to IS-702 grade 85/25 @1.20 Kg/Sqm over bitumen primer conforming to IS-3384 @0.40 Kg/Sqm with final coat of bonding bitumen grade 85/25 @1.20 Kg/Sqm over APP membrane with all overlaps complete all as specified and directed.

M&L for coved fillet in PCC 40mm thick (minimum Consolidated thickness) Type B-0 (1:2:4), using 12.5 mm graded crushed stone aggregate as in padding finished even and smooth without using extra cement with existing slope with 'V' shaped groves 6mm wide and 10mm deep @ 0.60 metre spacing both bays or part there of on top of padding and filled with mastic bitumen of 1:1 preparation complete all as specified and directed.

Supply & fixing of framed work such as grills, gratings, cooler stands, chowkhats etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde E-165 incl necessary fixing to walls complete all as specified and directed.

M&L for 10mm thick rendering on concrete surfaces of roof projection cornices & chajja etc finished fair and even without using extra cement including WPC in CM 1:4 incl taking down existing cement plaster and including necessary arrangements to work on roof projection, cornice & chajja etc. complete all as specified and directed.

S&F in repairs 20mm bore Gun-Metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F 50mm bore LDPE (Low density Polyethylene Pipes) of pressure rating 6Kgf/Sqcm fixed complete to walls,ceilings or in floors including taking down of old GI tubing, 40 mm bore all as specified and directed.

S&F Polymer coloured (Polypropeylene Delrin and ABS) low level flushing cistern 10 Ltr capacity, valveless syphonic action type complete with inlet ball valve float valve bends brackets, rawl plug, brass screws handle etc complete having BIS derscription mark with 2731 with and including suitable size of MS brackets, plug, screws all as required incl taking down existing high level/low level flushing cistern any type disconnecting pipes and jointing with new one etc and making good the floors/walls as per existing floor finish/wall finish including 32 mm bore PVC flush pipe and jointing with Water closet of any type complete all as specified and directed.

S&F wash hand basin vitreous china white oval type counter below type of size 570 x 445 mm, waste pipe, fittings and brackets etc complete all as specified and directed.

S & F Vitreous China, Squatting pan Orissa pattern size 580 x 440mm, white with integral foot rests (excluding flushing cistern and flush pipe ) with Vitreous China ‘P’ or ‘S’ trap, front or back inlet including connection to trap and to flushing pipe, anti syphonage pipe, front or back inlet and integral foot rests of any pattern complete including provision of lime concrete bedding, trap and connection to flush pipe complete all as specified and directed.

S&F Vitreous China premium quality/1st quality wash down water closet EWC with & excl flushing cistern of capacity 10 Ltrs complete one set white (closed pattern incl all necessary accesories like rag bolts/gel gasket etc. (excluding flushing cistern & flush pipe ) with ‘P’ or ‘S’ trap of dia 100mm including provn of lime concrete bedding complete all as specified and directed.

S&F plastic water closet seat white, closed pattern with flat bottom and cover and mild steel CP or Aluminum hinging device complete all as specified and directed.

S & F in repairs for Brass CP Sink Mixer with Swinging Casted Spout (Wall Mounted Model) for mixing hot & cold water with Connecting Legs & Wall Flanges, Confirming to IS complete all as specified and as directed.

S & F in repairs Brass CP mixer for WHB for mixing hot & cold water screwed down for iron/CPVC pipe and fixed with Connecting Legs & Wall Flanges, Confirming to IS complete all as specified and as directed.

S & F in repairs for Brass CP Wall Mixer with Provision For Overhead Shower with 115mm Long Bend Pipe On Upper Side, Connecting Legs & Wall Flanges, confirming to IS complete all as specified and as directed.

S&F in repair bib tap screwed down high pressure, cast copper alloy, fancy type, ISI marked, with crutch or butterfly handles screwed down suitable for 15mm bore pipe or union, complete all as specified and directed.

S&F in repair 15mm bore concealed stop valve type chromium plated cast copper alloy screwed down high pressure screwed both ends for iron pipe or for union all as specified and directed by Engr-in-charge.

S&F in repair brass chromium plated tubular towel rail 20mm dia 'D' type 60cm long between flanges all as specified and directed by Engr-in-charge.

Dismantling of existing unserviceable water tank of any description capacity exc 500 Ltr but n.exc 1000trs capacity and S&F in repair rotational molded polyethylene water storage tanks white in colour, tripple layered with threaeded lid/cover, weight of tank should not be less than 36.00 Kg (cylindrical vertical with closed top) capacity 1000 Ltr hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I and Engr-in-charge. (Make:- Sintex/ Rotex/Vectus)

S&F in repair ball valves PTMT high pressure with epoxy coated aluminium rod and high density plastic ball, screwed for iron pipe, 20mm bore compete (Minimum weight 210 gm) complete all as specified and directed.

Taking up or down 15mm dia steel tubing and connections by disconnecting fittings/tubing from existing tubing were required including cleaning for refixing or removal from site complete all as specified and directed.

Taking up or down 20 mm dia steel tubing and connections by disconnecting fittings/tubing from existing tubing were required including cleaning for refixing or removal from site complete all as specified and directed.

Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings 16mm dia bore on walls/ceiling or laying in floors or fixing as in concealed to walls or in floors etc, and making good the surfaces matching to exsiting surfaces of walls/ floor to the entire satisfaction of Engineer-in-charge.

All as per item No 119.00 above but 20mm dia bore, complete all as specified and as directed by the EIC.

S&F in repair stop valves, 15mm dia chromium plated, cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipes or unions, complete all as specified.

S&F in repair angle cock 15mm dia chromium plated, cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipes or unions, complete all as specified.

Taking down old unserviceable kitchen sink and S&F kitchen sink without drainage board overall size not less than 495mm x 420mm, bowl size 410 x 330 x 160mm made of stainless steel 1.00 mm thick with plugs, washers and waste including fixing cantilever brackets and connecting union complete all as specified and directed.

Taking down old unserviceable PVC connection and S&F 15 mm bore PVC connection, heavy duty, 45 cm length with two Nos PTMT nuts at both ends of approved quality complete all as specified and directed

S&F in repairs stainless steel grating openable 100mm dia without hole including fixing with white cement complete all as specified.

S&F in repair fancy type shower rose 125mm dia size of Rim and 30cm long CP brass pipe with swiwel joint, including fixing to steel pipe or union of 15mm bore and fixed complete all as specified and directed.

S&F in repair glass shelf assembly consisting of made out of 5.5 mm thick glass shelf 12 cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F in repair stainless steel soap dish any type, fixed to plugs with chromium plated brass screws embedded in the wall complete all as sped & directed. Make: Prayag, Cat No BA-15 S

S& F 0.63 mm thick galavanised corrugated mild steel sheeting with two corrugation side lap,with L- type or J- type or crancked hook bolts in lieu of screws with washers in roofs, walls etc with grade of zinc coating 275 all as specified and directed.

S& F 0.63 mm thick plain galavanised mild steel sheeting in ridges,hips, valley gutters drip & straight flashing with grade of zinc coating 275 all as specified and directed.

S& F steel work in roof trusses (framed), trussed, purlins, crane gantries, rails, and fastenings and heavy bracket framing(Beam, tee,angle, channel or flat sections) incl distance pieces, cleats etc conforming to IS-1161-1979 grade FE-410-W( Gde-E-250) Incl complete fittings all as specified and directed.

Taking down carefully copper / aluminium point wiring (light, fan, socket or power) complete, including fittings such as switches, ceiling roses, holders, regulators, sockets etc., removing materials from site and making good disturbed surface of walls, floors etc. complete all as specified and directed.

Disconnecting and taking down unserviceable sub main wiring of any size including steel/PVC conduit and accessories & removing from site and making good the disturbed surfaces, complete all as specified and directed.

Taking down carefully by unscrewing from boards / outlet boxes, fittings and fixtures such as switches, sockets etc for reuse at site or carrying to the store(To be measured only when found serviceable in all respects complete for reuse.) complete all as specified and directed

M&L for point wiring with 1.5 Sqmm. (nominal area) single core PVC insulated 1100 Volts, grade multi stranded FRLS copper conductor unsheathed cable in and including PVC rigid non metallic conduit medium grade not less than 20mm dia ISI marked and fittings and accessories concealed in walls/roof/ ceiling with suitable size of sunk type pressed steel modular terminal box and modular white cover plate with frame for suitable module as per site requirements for mounting of modular switches, sockets, fan regulator etc and one green colour cable of 1.5 Sqmm. (nominal area) single core PVC insulated 1100 Volts, grade multi stranded FRLS copper conductor unsheathed as earth wire up to common earth and connected to earth for the following, complete all as specified and directed for:-

All as per item No. 135.00 here-in-before but One light point controlled by one, one way switch.

All as per item No. 135.00 here-in-before but One ceiling fan/exhaust fan point controlled by one, one way switch.

All as per item No. 135.00 here-in-before but One three pin 5 Amp socket on same board with other switches.

All as per item No. 135.00 here-in-before but One 3 pin 5 Amp socket on independent board.

All as per item No. 135.04 here-in-before but with 2.5 Sqmm, for one 5 pin 5/15 Amp socket on independent board including 2.5 Sqmm stranded copper conductor (FRLS) PVC insulated green in colour as continous earth conductor connected to common earth complete all as specified and directed.

S&F of modular switch 1 way 6/10 Amp 1 module complete all as specified and directed.

S&F of modular switch 1 way 16 Amp 1 module complete all as specified and directed.

S&F of modular socket 6 Amp, 2/3 pin combined 2 module complete all as specified and directed.

S&F of modular socket 6 Amp/16 Amp, 2/3 pin combined 2 module complete all as specified and directed.

S&F ceiling rose surface bakelite 3 terminals 63.5 x 17 mm complete all as specified and directed.

Taking down existing exhaust fan & wall mounted fan and re-use at site or carrying to the store (To be measured only when found serviceable in all respects complete for re-use) complete all as specified and directed.

S&F exhaust Fans AC single phase 230/240 volts of size 300 mm sweep with louver including connecting with three core flexible copper wire from ceiling rose to connector of fan complete all as specified and directed.

S&F of ventillation fan 250mm sweep non metallic white colour including connecting with three core flexible copper wire from ceiling rose to connector of fan complete all as specified and directed.

S&F of lamp holder PVC/polycarbonate type with back plate complete all as specified and directed.

S&F LED box type tube light fitting 20 watt made up of CRCA sheet with pre wired double sided connections including 1x20 watt retrofit LED tube rod with extruded aluminium body , PC diffuser and inbuilt driver , double sided connection, complete with all accessories internally prewired complete all as specified and directed

S&F ceiling fan 1200 mm sweep , 230 Volts, AC , 50 Hz, copper winded motor, BE star rated white colour complete with motor, blade set of three nos , down rod, canopy, shackle assy complete all as specified and directed.

Supply and fixing wall mounted decorative luminarie fitting suitable up to 9/10 Watt LED lamp champagne gold finish fixture with plastic body suitable for B22 Base complete all as specified and directed by Engr-in-Charge. Make: Havells , Model- LHFOECE1TZ1O014, HSN Code: 9405 or equivalent model of Mepro/Philips

S&F LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.

S&F LED light fittings, 10 W bulk head luminaries 230V, 50 Hz complete with all accessories and including connecting up with three core copper conductor cable with suitable size complete all as specified and directed.

Supply, fixing and testing energy saving street light luminaire 25 watt LED , pressure die cast housing with high power LED as lighting source and lens embedded PC cover with IP 66 protection incl connecting with three core copper flexible wire from ceiling rose to connector of light fitting complete all as specified and directed by Engr-in-Charge.

S&F room window type air conditioner electric driven (single phase), cooling capacity 4500K Cal per hour ( 1.5 Ton) BEE 5 star rated complete all as specified and directed by Engr-in-Charge. Make :- Bluestar/Havells/LG

S&F in repair surface mounted LED downlight 18 watt round shaped , Slim surface mounted LED panel with premium diffuser to ensure glare free & even light distribution complete all as specified and directed. Make:- Havells, Model -Trim Cosmo Surface Round, Cat Part No LHEAAHP7IL1W018, or equivalent model of Philips/Compton

S&F street light bracket made of 32 mm GI pipe , 1.2 mtr lenght fixed with two nos of clamp, nut and bolts complete all as specified and directed.

S&F water heater storage type,electric, capacity 25 litres, BEE 5 star rated, 240 volts, input 2000 KW, PUF insulated fitted with stainless inner container and cooper coil of BEE 5 star rating models, max working head of water 25 Ltrs, fixed to wall with suitable MS tower/anchor bolts,Inlet/outlet pipes incl PVC connections grouted to wall, complete all as specified and directed. Make: Havells/Usha/Bajaj.

M & L for submain wiring with two single core PVC insualated, unseathed, FRLS, 1100 volts grade 6 sqmm multi stranded copper conductor cable drawn through and incl 25 mm dia PVC non metallic rigid concealed conduits and the conduits accessories incl one run of green colour earth continuity conductor with 6 sqmm multi stranded copper conductor cable complete all as specified and directed.

M & L for submain wiring with two single core PVC insualated, unseathed, FRLS, 1100 volts grade 4 sqmm multi stranded copper conductor cable drawn through and incl 25 mm dia PVC non metallic rigid concealed conduits and the conduits accessories incl one run of green colour earth continuity conductor with 4 sqmm multi stranded copper conductor cable.

M& L for TV Socket incl PVC conduit and co axial cable wire complete all as specified and directed.

M& L for Telephone socket incl PVC conduit and telephone wire complete all as specified and directed.

S & F single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole 20 Amp MCB SP `C' series for AC complete all as specified and directed

Taking down and Supply and fixing of Change over Three Pole Neutral AC 63 Amp, with bolted type fuse in sheet enclosure with fuses complete all as specified and directed. Make: Havells Cat No IHKDTW4063 or equivalent.

S&F of MCB distribution board TPN 4 way, 415 volts, double door, with 200 Amps rated bus bar, neutral bar with shrouds, earth bar, IP-43 , made out of sheet steel enclosure, recessed type, factory made powder coated suitable for housing MCBs as incomer and outgoing including blanking plate complete all as specified and directed. Make: Legrand/Schneider/Seimens Note: MCB DB and MCB SP/SPN will be of same make.

S&F of MCB distribution board,08 Ways, 240 volts SPN (single pole & neutral) IP-43 double door metal, 240 volt made out of CRCA sheet steel , factory made powder coated with insulated bus bars , shrouded neutral bars, earth bars , made out of sheet steel enclosure, recessed type, factory made powder coated suitable for housing MCB's complete all as specified and directed of following size:- Make: Legrand/Schneider/Seimens Note: MCB DB and MCB SP/SPN will be of same make.

S & F of MCB SP, 240 volt, 6 Amp to 40 Amp capacity, 10 KA, 'C' curve complete all as specified and directed. Make : Legrand (DX-3), Schneider (Acti-09), Siemens ( Betagard)

S & F of MCB SP, 240 volt, 63 Amp capacity, 10 KA, 'C' curve complete all as specified and directed. Make : Legrand (DX-3), Schneider (Acti-09), Siemens ( Betagard)

S & F of MCB SPN, 240 volt, 63 Amp capacity, 10 KA, 'C' curve complete all as specified and directed. Make : Legrand (DX-3), Schneider (Acti-09), Siemens (Betagard)

S&F of MCB TPN, 415 volt, 63 Amp capacity, 10 KA, 'C' curve complete all as specified and directed. Make : Legrand (DX-3), Schneider (Acti-09), Siemens (Betagard)

M&L for earthing complete with galvanised steel earth plate electrode 60cmx60cmx6 mm thick buried directly in ground vertically to a depth not less than 2.25m below ground level with top edge of the earth plate at a depth not less than 1.5m below ground level, connected to galvanised earth lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel and other end of earth wire connected to main switch board and protected by galvanised iron pipe light grade 15mm bore and water pipe 20 mm bore GI med grade with funnel and wire mesh PCC chamber in cement concrete 1:3:6 type C-2 and RCC cover with handle all as specified and shown in elect plate No 3 of SSR Part-I of 2009 incl dismantling of old unsv existing earthing complete all as specified and directed.

S&F in repair recess mounted 2' x 2' LED luminarie 36 watt, cool day/warm white light with white powder coated CRCA housing with LED driver, efficiencey >100 Lm/w complete all as specified and directed.

S&F of MCB distribution board single pole & neutral with 200 Amps rated bus bar, double door IP-43 DB's , made out of sheet steel enclosure, recessed type, factory made powder coated 4 way, 240 volts suitable for housing MCB's including blanking plate complete all as specified and directed.

S & F of MCB SP, 240 volt, 6 Amp to 40 Amp capacity, 10 KA, 'C' curve complete all as specified and directed. Make : Legrand (DX-3), Schneider (Acti-09), Siemens (Betagard)

S & F of MCB SPN, 240 volt, 36 to 63 Amp capacity, 10 KA, 'C' curve complete all as specified and directed. Make : Legrand (DX-3), Schneider (Acti-09), Siemens (Betagard)

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 sq mm 3.5 core complete all as specified and directed.

S&F tubes light grade GI tubing 40 mm dia with all fitting laid in trenches, fixed on pole/on wall for cable protection complete all as specified and directed.

Excavating in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. or for cable laying or not exceeding 10 sqm on plan and not exceeding 1.5 m in depth and getting out in soft/ loose soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in soft/ loose/ hard/ dense soil complete all as specified and as directed.

Removing excavated material (soils) not exceeding 50 m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed.

Supply & spreading in trenches dry river sand cushioning to underground cable in trenches including spreading, levelling hand punning down complete all as specified and directed Note:- Depth of sand cushioning will be measured after punning down and levelling the sand properly complete all as specified and directed.

M & L for laying of bricks locally available sub class 'B' bricks, non-modular sizes as per IS 1077: 1992 for cable protection cover laid flat and dry in trenches over the cable perpendicular to the direction of cable all as directed.

S&F tubes medium grade GI tubing 20 mm dia with all fitting laid in trenches, fixed on pole/on wall for cable protection complete all as specified and directed.

S&F 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

MITTAL ENTERPRISES

H M LAXMINARAIN

M/S AL ASMA ENTERPRISES

Shree Sai Ram Enterprises

V K LAKWAL CONSTRUCTION