SPECIAL REPAIR TO BUILDING NO T 415 AND T 417 AND PROVN OF VEH SHED AT SILA GARRISON UNDER AGE (I) CIF(U)

Amount

M&L Brick work with sub class 'B' bricks straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6, complete, all as specified and directed.

M&L Reinforced cement concrete M-25 design mix using 20 mm graded crushed stone aggregate as slabs supported on walls, beams and columns, in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete, all as specified and directed.

M&L Use and waste of form work to sides and soffits of floors or roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves including supports, overhanges etc also splays between floors and beams etc. rough finished concrete surface of concrete, complete, all as specified and directed.

M&L 15 mm thick rendering on fair faces of brick/concrete surfaces in cement mortar 1:6 and finished even and smooth without using extra cement, complete, all as specified and directed.

M&L for preparing plastered or unplastered new surfaces of walls and applying three coats of white wash, complete, all as specified and directed.

M&L TMT bars 10mm dia and over in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with Mild Steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified.

M&L Rolled mild steel section as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors ; fixed with angle cleats or other connecting plates conforming to grade Fe 410-W(Gde-E250)quality-A including one shop coat of red oxide zinc chrome primer (including preparation), complete, all as specified and directed.

M&L Preparation of new steel and iron surfaces not otherwise described exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer, complete, all as specified and directed.

Dismantling wall and ceiling boards, fibre pulp insulation etc) or insulation boards/slabs/blankets, any thickness, including cover fillets, complete, all as specified and directed.

S&F Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples, complete, all as specified and directed.

S&F Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples, fixed in repairs, complete, all as specified and directed.

M&L Preparation of old steel and iron surfaces not otherwise described exceeding 10 cm width or girth and applying two coats of synthetic enamel paint, complete, all as specified and directed.

Hacking out old broken glass panes (any thickness size, quality or description) from wooden frames including punching or drilling out old glazing pins/spring clips and providing and fixing new ones, complete, all as specified and directed.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane, complete, all as specified and directed.

S&F 3mm thick figured glass pin head type and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane, complete, all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises, complete, all as specified and directed.

M&L Non-skid coloured ceramic (square or rectengular) 7 to 8 mm thick, area of each tile exc 0.18 sqm but not exc 0.38 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface including 15mm thick screed bed in CM 1:4, complete, all as specified and directed.

S&F Steel windows/ ventilators with tube frame factory made with double door shutter (wire gauged shutter and glass/glazed shutter) of size 79mmx39mm, 16 gauge rectengular tubular frame with side hung shutter with glazing bars 12x3mm flat Iron including box type hinges with steel handle and steel peg stay dovetailed or welded including 02 nos tower bolts 100mm long and 10mm square bar grills complete with two coats of synthetic enamel paint over one coat of red oxide zinc crome primer including taking down old windows/ventilator, all as specified and as per drawing No. CEUZ/TD/1269/2008 Sh 1/1 to 1/3. Note: Wire cloth and glass panes shall be measured and paid seperately under respective item.

Dismantling of plain or corrugated steel sheeting, any gauge and thickness in roof covering including Nainital or similar pattern roof covering, complete, all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete, all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, complete, all as specified and directed.

S&F Gl frame work for seamless ceiling (grid size 605mmx605mm) comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre, complete, all as specified and directed.

6mm thick Non -asbestos fibre cement building boards fixed or laid/ inserted to timber/ GI/ Aluminium framework with screws, complete, all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor and in paving not exceeding 15 cm thickness (below or above ground level), complete, all as specified and directed.

Excavating in trenches n.exc 1.5m wide and n.exc 1.5m in depth in any type of soil for foundation, etc, or for shafts, wells, drain pipes or laying of cable or pipes, trimming the sides, forming bottom surfaces to required leve, n.exc 10sqm on plan and getting out, complete, all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick, complete, all as specified and directed.

Removing surplus soil to a distance n.exc 50m and deposited where directed at a level not exceeding 1.50 m above the starting point, complete, all as specified and directed.

M&L Cement concrete 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc ; basement slabs, under- reamed piles and mass concrete, complete, all as specified and directed.

TMT bars 6 to 8mm dia and over in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with Mild Steel wire (annealed) not less than 0.9mm dia, complete, all as specified and directed.

TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with Mild Steel wire (annealed) not less than 0.9mm dia, complete, all as specified and directed.

S&F Rolled mild steel as in roof trusses ( framed) trussed, purlins, crane gantries, rail,and fastening and heavy brackets framing ( Beam, tee, angle, channel or flat sections ) including distance pieces, cleats etc conforming to Fe 410-W (Gde-E250) quality-A, complete, all as specified and directed.

S&F compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates, etc. complete, all as specified and directed. conforming to Fe-410-W (Gde E-250) quality - A.

INTERNAL ELECTRIFICATION Taking down carefully copper/aluminum point wiring (light, fan, socket or power) complete with fittings such as switches, ceiling roses, pendants, regulators, sockets brackets, switch boards etc and making good disturbed surfaces of walls, floors etc , complete, all as specified and directed.

M&L for point wiring for one light / fan point controlled by one, single pole, one way switch, 5 amps with 1.5 sqmm, PVC insulated but unsheathed, multi stranded copper conductor FRLS cable, IS-694 marked, drawn through and including non metallic rigid PVC concealed conduit 20mm dia or higher 1.5mm thick complete with all PVC conduit accessories / fittings ISI marked and sunk type pressed steel terminal switch boxes 1.5 mm thick duly painted with black bituminous paint over one coat of red oxide primer with plastic laminated sheet top cover 3mm thick make hylam, brass screws and cup washers including 1.5 Sqmm multi stranded copper conductor PVC insulated green in colour as continuous earth conductor to common earth and connected to earth dolly with all accessories , complete, all as specified and directed.

All as per item No 2 but one 3 or 5 pin 5 Amp socket outlet on independent board.

All as per item No 2 but one 3 or 5 pin 5 Amp socket outlet on same board.

All as per item No 2 but one 3 pin 15 Amp socket outlet with cable 4.0sqmm for neutral and live wire and 2.5 sqmm for earth on independent board.

S&F LED Fluorescent tube light fitting, 1 x 20 W, LED integrated Batten T5 indoor decorative aluminium extruded T5 LED Battens - integrated type white complete with all accessories with twin core twisted flexible copper conductor cable with suitable size, complete all as specified and directed. Make:- C & S, Model :- Nakshatra-20W, Cat Part No :- LTTB4F20WLED/W - 4 ft White or equivalent in Bajaj/Havells/CG.

S&F Lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings including 10 watt LED lamp, in white colour with maximum lumen output (LM) 850, 10 Watt, Base Cap - B22, Complete all as specified. Make :- Havells, Cat Part No LED ADORE 10W B22 CDL BALL LAMP LHLDERUEML8X010 or equivalent in Bajaj/Philips/Cropmton Greaves

S&F 1 X 10 w LED bulk head luminaries, IP65 LED Bulk Head in engineering plastic housing with clear prismatic diffuser with lamp holders , etc. Complete with all accessories and including connecting up with twin core twisted flexible copper conductor cable with suitable size of 230 V, 50 HZ, complete all as specified and directed. Make :-C&S e-TARTA Series Cat Part No e-TARTA/10 watt CG801B10WLED White or equivalent in Bajaj/Havells/CG.

S&F switch piano 5A flush button type single pole one way, complete all as specified and directed.

S&F ceiling rose surface bakelite 65x50mm, two to three terminal isolated body fixed on PVC round block, complete, all as specified and directed.

S&F Switch socket combination 2 in 1, 5 pin, 5 Amp flush type universal, complete all as specified and directed .

S&F Switch socket combination 2 in 1, 3 pin, 5 and 15 Amp flush type universal, complete all as specified and directed.

S&F Isolator single pole and neutral 40 Amps, 240 V complete all as specified and directed.

S&F Isolator tripple pole and neutral 63 Amps, 415 V, complete all as specified and directed.

S&F MCB single pole 6 to 32 lamps, 240V, complete all as specified and directed.

S&F sheet metal enclosure for DBs double door when MCBs to be used Single pole and neutral with 200 amps rated bus bar 240 V 4 way, complete all as specified an directed.

S&F sheet metal enclosure for DBS double door when MCBs to be used single pole and neutral with 200 Amps rated bus Bar 240 V 8 way, complete all as specified an directed.

Taking down the existing ceiling fan, refixing and rehanging the same in existing position incluiding making connection with suitable copper cable from ceiling rose to fan, complete all as specified an directed.

S&F in replacement with electronic step type fan regulator 120 watt 230 volts 50 C/S deluxe modular type suitable for 1200/1400mm ceiling fan including taking down old regulator, complete all as specified and directed.

Supply, laying and testing cable XLPE insulated screened PVC bedded, galvanised steel strips or wire armoured, electric power cable (heavy duty) with stranded aluminium conductor, 1100 volts grade of size 25 sqmm 4 core, including taking down old unserviceable aluminium cable, complete all as specified and directed.

S&F Circuit/Submain wiring of size 2x 6.0 Sqmm in PVC conduit alongwith earth wire in green colour of size 1 x 4.0 Sqmm of FR PVC insulated copper conductor, single core cable in surface/ recessed as required, including taking down old unserviceable submain wiring, complete all as specified and directed.

M&L for dry sand cushioning to under ground cable 8cm thick before laying the cable and 15cm thick after laying the streching the cable in trenches, including hand punning and consolidating complete all as specified. Note : for payment purpose punned thickness shall be measured.

M&L for sub class ‘B brick, old size, as cable protection cover, laid dry, flat, transversally along the length of cable, on sand cushioning, with width equal to the length of the brick, complete, all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground, (earth pit not less than 1.5m below normal ground level), with top edge of plate not less than 1.5M below normal ground level, connected to and including galvanised earth wire 4mm dia by means of nut, bolt, check nuts and washers of galvanised iron or steel as shown on electrical plate No. 03 of SSR Part-I (2009). complete all as specified and directed including testing on completion including following:- (a) Excavation and earth work for drilling hole for electrode in any type of soil. (b) PCC pit in cement concrete 1:2:4 type B-1, Precast RCC cover in cement concrete 1:2:4 type B-1with suitable handle, reinforced with welded steel wire fabric weighing not less than 1.87 Kg/Sqm. (c) Funnel with watering pipe of GI 20mm nominal bore light grade and lugs etc . (d) 15mm nolinal bore medium grade GI protection pipe 5M long for protection of earthing lead. (e) Requisite quantity of common salt and charcoal. (f) Testing of earthing on completion as directed.

M/s Hari Om Enterprises