8841/E8

Amount

Demolition Brick Work built in Cement Mortar including all Quoins, Arches, Pillars, etc, but excluding Ashlar Facings, dressed Stone Work and Pre-cast Concrete Articles of any descriptions, complete all as specified and as directed.

Taking down shutters of any description n exc 1.00 sqm each and removing from site or to store as directed by Engineer in charge.

Taking down shutters of any description exc. 1.00 Sqm but n.exc 2 Sqm each and removing from site or to store as directed by Engineer in charge.

Taking down PVC door chowkats or frames with PVC shutter exc. 1.00 Sqm and n.exc 2 Sqm each complete all as specified and directed.

Taking down Cement Plaster of any description on Brick Walls, Concrete Surfaces including racking out joints, hacking for key, scrubbing down with Water, remove dust, debris/ rubbish, etc., complete all as specified and as directed.

Dismantling Floor, Hearth or Wall Tiling including Cement Mortar Bedding (but not backing), and removing rubbish off the Premises, complete all as specified and as directed.

Taking up or down Steel Water Tubing 15mm dia (bore) including Connections and Fittings, Segregating Serviceable Pipes & Fittings, Stacking properly at Site(s) and keep in Safe Custody for re-use, complete all as specified and as directed.

M&L Brick work with sub class 'B' bricks straight or curved on plan exec to any radius in half brick thick wall, built in cement mortar 1:4 complete all as specified and directed.

S&F for Solid PVC Door Frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet reinforced with M.S. Square tube, fixing in opening as per Specifications and Drawings shown in MES Schedule Part-II, complete all as specified and as directed.

S&F for Factory Made Solid PVC Molded Door Shutter With Wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick 3D wood grain Molded PVC Sheet Polyurethane painted on the front face & 2mm prelam PVC Sheet on back face, fixed to frame at site complete all as specified and directed.

S&F 35mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides fitted to chowkhats complete all as specified and directed.

M&L 2nd class hardwood plain fillets square rectangular or triangular in section, wrought fixed with screws area exc. 3 Sqcm but n.exc 6 Sqcm complete all as specified and directed.

S&F Fancy type, Powder coated 20/25 mm dia of drapery rod fixed in position as in repair complete all as specified and as directed

S&F Bracket for fixing Fancy type,Chromium Plated 20mm dia curtain rod/ drapery rod etc as in repair complete all as specified and as directed.

S&F Mild Steel Butt Hinges, size of Hinges 100mm, medium weight, Cold Rolled and fixed, complete all as specified and as directed

S&F in repair Mild Steel Butt Hinges, size of Hinges 100mm, medium weight, Cold Rolled and fixed, complete all as specified and as directed

S&F Aluminum anodized, barrel tower bolts of extruded section, 150 mm long and fixed with steel screws complete all as specified and directed.

S&F in repair Aluminum anodized, barrel tower bolts of extruded section, 150 mm long and fixed with steel screws complete all as specified and directed.

S&F Aluminum alloy Handle 150mm long, Extruded Section, Fabricated type, anodized and fixed, complete all as specified and as directed.

S&F in repair Aluminum alloy Handle 150mm long, Extruded Section, Fabricated type, anodized and fixed, complete all as specified and as directed.

S&F 250 mm long Aluminum alloy, anodized, Sliding Door Bolt with Hasp, Staple (Bolt type) and Fixing Clips of Sheet, Cast or Extruded Sections and Fixing Bolts and Sliding Bolts of Extruded Sections or Cast-Aluminum alloy and fixed, complete all as specified and as directed.

S&F in repair 250 mm long Aluminum alloy, anodized, Sliding Door Bolt with Hasp, Staple (Bolt type) and Fixing Clips of Sheet, Cast or Extruded Sections and Fixing Bolts and Sliding Bolts of Extruded Sections or Cast-Aluminum alloy and fixed, complete all as specified and as directed.

S&F 40mm dia, cupboard knobs fixed with nut, screw and washer of brass polished bright finished as in repair complete all as specified and as directed.

S&F in repair self closing hinges fixed on cupboard/ door/window etc with screw complete all as specified and as directed.

S&F in repair 30mm width of flaps Continuous (piano) hinges, mild steel, bright finish or electro galvanised complete all as specified and as directed.

S&F in repair Floor door stopper of steel body and overall length of cover plate 75 mm and tongue anodized with hard drawn steel spring as in repair complete all as specified and directed.

S&F in repair Powder coated anodized aluminum sliding fly proofing window, three tier (two shutter of glass and one shutter on wire mesh) without glazing bar, window shutter style shall be 40mm X 19mm, sheet thickness 1.5mm ,sliding channel 3mm thick channel width shall be as required and directed by Engr-in-Charge with roller. Frame (Chowkats) of window shall be 75mm X 60mm X 1.5mm thick section with or without rebate with 5.5mm thick tinted glass and galvanised wire cloth 0.36mm nominal dia of wire and average width of aperture 1.18mm aluminum glazing clips fixed with rubber gasket locking arrangement all as directed by Engr-in-Charge. Note - (i) Measurement shall be taken clear opening ie out to out of window frame as a whole including all fittings and fixture and no cost extra shall be paid separately. (ii) Cost of glass and wire cloth shall be included in quoted rates.

M&L for Repairs to any type of Aluminum Doors, Aluminum Windows, Aluminum Ventilators, Aluminum Louvers, Aluminum CB shutters etc of any description, in any situation by taking down & refixing shutter including replacement of joining cleats, glazing clips, rubber neoprene packing, aluminum snap beading, screws & tightening, adjustment etc ,making smooth functioning (proper closing, opening) etc with entire satisfaction of Engineer-in-charge complete all as specified and directed.

M&L for Petty repairs to wardrobes, cupboard, kitchen cabinet, Showcase items of any description in any situation including Resecuring, easening of shutters, shelf etc including taking down and refixing in position with new nut, screw ,washer etc including adjusting, tightening of builders hardware such as lock, wiremess, glass pane, Ball catches, knobs ,hasp and staple ,piano hinges, handles & refixing builders hardware in same/other position making smooth functioning (proper closing, opening) etc with entire satisfaction of Engineer-in charge complete all as specified and directed

M&L for Repairs to any type of wooden joinery works of shutters, shelf etc such as door, window, Ventilator of any description in any situation by taking down & refixing in the same opening including Resecuring, easing, adjusting ,refixing builders hardware butt hinges, tower bolts,handles,sliding door bolts,rat tail,lock,ball catches,knobs,hasp & staple,peg set,door stopper,piano hinges,door cill strip etc wiremess,glass pane in same/other position, renewal of screws, welding (if required) etc,wooden beading & tightening of GI/steel wiremesh etc making smooth functioning (for proper closing ,opening) etc with entire satisfaction of Engineer-in-charge complete all as specified and directed

M&L Prelaminated particle board 18/19mm thick as in cup board shutter and Shelf, interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination fixed with screws to timber frame works including taking down old unserviceable particle board complete all as specified and as directed.

M&L Glazed Ceramic Coloured Tile 450x350x7mm thick on Vertical Surfaces such as Skirting, Dados, Risers to Steps, etc., Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Shade of the Tiles over and including 10mm thick backing layer in cement mortar (1:4) complete all as specified and as directed.

M&L joint free non skid ceramic coloured tiles 7-8mm thick (square/rectangular) area of each tile exc 0.06 Sqm but not exc 0.11 Sqm in floor set and jointed in in neat cement slurry and pointed in cloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L Vitrified Ceramic Tiles 10 mm thick (square/ rectangular) in dark Shade, Polished, area of each tile not exc 0.36 sqm as in Floors, etc. Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Shade of the Tiles over 20mm thick screed bed in cement sand mortar (1:6) complete all as specified and as directed.

M&L Granite (of any type) Work (Table rubbed and polished) 18 to 20 mm thick, in Steps, Cooking Platforms and like, Set in Screed bed of 20mm thick in Cement Mortar 1:4 including Pointing in White Cement 1:2 using Marble Dust with admixture of Pigment to match with Shade of Granite including Cutting and Polishing including half round edges, including demolition of old tiles complete all as specified and as directed.

M&L as in patch repair Non-skid Ceramic Coloured Tiles, 7.0mm to 8.0mm thick (square/rectangular), area of each tile exc 0.18 sqm but not exc 0.36 sqm in Floors, etc. Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Shade of the Tiles over 15mm thick screed bed (1:6) in cement mortar including demolition of old tiles complete all as specified and as directed.

M&L as in patch repair area not exceeding 05 sqm each & matching with existing tiles for Vitrified Ceramic tiles 8-10 mm thick light/Dark shade (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 15mm thick screed bed in CM 1:4 including dismantling existing tiling with cement mortar bedding complete all as specified and directed.

M&L as in patch repair work area not exceeding 05 sqm each & matching with existing tiles for (first quality) (07mm to 10mm) thick coloured Glazed ceramic tiles including digital/printed/High lighter tiles in vertical surface such as dado, pillar etc area of each tiles not exceeding 0.18 sqm , set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of the tiles over and including 10mm thick rough cement plaster to receive tiles in CM 1:4 including dismantling existing tiling with cement mortar bedding complete all as specified and directed. Note for item Nos 36.00 to 42.00:- The bidder quoted rate shall be included for all straight, Raking or circular cutting, wastage on tiles & texture, colour, size, Shade, laying of tiles to any pattern & any design with one or more colours as approved by GE.

M&L for 5 mm thick plaster n.exc. 3 sqm each patch on brick or concrete surfaces of wall in CM 1:3 and finished even and smooth without using extra cement complete all as specified & directed.

M&L 15mm thick plaster n.exc. 3 sqm each patch in Cement Mortar 1:6 on Brick Walls or on Concrete Surfaces, finishing plastered surfaces Even and fair without using Extra Cement complete all as specified and as directed.

M&L Preparing old decorated Plaster Surfaces of Ceiling and applying One Coat of oil bound distemper (any colour /tint) complete all as specified and as directed.

M&L Preparing old decorated Plaster Surfaces of Wall and applying One Coat of oil bound distemper (any colour /tint) complete all as specified and as directed.

M&L preparing new plastered surfaces of wall and and applying Two Coats of Distemper Oil Emulsion over a coat of primer over and including 2mm thick water proof wall care putty including rubbing with emmery paper to make wall surface smooth and even complete all as specified and as directed.

M&L preparing new plastered surfaces of ceiling surface and and applying Two Coats of Distemper Oil Emulsion over a coat of primer over and including 2mm thick water proof wall care putty including rubbing with emmery paper to make wall surface smooth and even complete all as specified and directed. complete all as specified and as directed.

M&L Complete removal of existing Treatment of old decorated Surfaces of Walls and applying Two Coats of Distemper Oil Emulsion over a coat of primer and applied over 2mm thick water proof wall care putty including rubbing with emmery paper to make wall surface smooth and even complete all as specified and directed.

M&L for preparation of old plastered Surfaces of Walls and applying One Coats of Exterior Emulsion Weather Coat Paint over a coat of Primer (as per Manufacturer’s instructions) complete all as specified and directed.

M&L Acrylic Oil bound Distemper on existing surface with the following Specifications and Manufacturer's instructions, complete all as specified and as directed :- (i) M&L Preparing Masonary surfaces cracks, large pores, dents or damaged portion with smart care crack seal. (II) M&L Applying two coats of smart care damp block 2K slurry by brush or roller over brick masonary surfaces,Allow 1st coat to dry for 4-6 hrs and then apply 2nd coat . (III) Applying a coat of 2mm thick acrylic wall putty (Make JK/Asian/Birla) (VI) Applying a coat of interior wall primer after smoothing wall putty surfaces with sand paper and two coat of acrylic oil bound distemper complete all as specified & directed. Note : Mixing of smart care damp block 2k , 60% powder and 40% liquid and use mechenaical stirrer

S & F in repair, stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples including if required fixing with wooden beads or MS flat of size 15mmx3mm & chromium plates screws/using metal nut and bolts or wooden beading,aluminium window fittings,neoprine rubber gasket etc if required including necessary scaffolding up to twelve storeys height of bldgs complete all as specified and directed

M&L Preparing old Wooden Surfaces of any description not otherwise decribed over 10 Cm width or girth and applying One Coat of Synthetic Enamel Paint (First quality), complete all as specified and as directed.

M&L Preparing old Steel Surfaces of any description not otherwise decribed over 10 Cm width or girth and applying One Coat of Synthetic Enamel Paint (First quality), complete all as specified and as directed.

S&F CPVC pipes 20 mm outer diameter of SDR 11 & plain CPVC SDR 11 fittings fixed on Walls, Ceiling or laid in Floors or any other Situation, etc up to four stories height of bldgs. complete as all specified and as directed.

M&L Cutting chase, pinning in making good to facings where required and pointing in cement mortar 1:3 to ends or edges of laddings, steps, cills, sushades, shelves, lintels etc and cutting chase for concealed water tubing or concealed coduit wiring etc and making good cutting grith n exc 10 cm girth on brick walls complete all as specified and directed.

S&F 20mm bore brass MTA for CPVC pipe as in repair complete all as specified and directed.

S&F 20mm bore brass FTA for CPVC pipe as in repair complete all as specified and directed.

S&F 20mm bore brass elbow for CPVC pipe as in repair complete all as specified and directed.

S&F 20mm bore brass Tee for CPVC pipe as in repair complete all as specified and directed.

S&F 20mm bore dia of pipe Ball valves high pressure of PTMT with epoxy coated Aluminum rod & high-density plastic ball screwed for iron pipe and fixed as in repair complete all as specified and directed.

S&F Cast Iron Nahani Trap with 100mm bore (dia) Outlet, with Gratings including jointing to Waste Pipe and fixed in Cement Concrete 1:2:4 (20mm graded aggregate), as in repair complete all as specified and as directed.

S&F Cast Iron Floor Trap with 100mm bore (dia) Outlet, with Gratings including jointing to Waste Pipe and fixed in Cement Concrete 1:2:4 (20mm graded aggregate), as in repair complete all as specified and as directed.

S&F 32mm bore PVC waste pipe flexible type including all cups and sockets with minimum length 800mm for any type/make/size for stainless steel sinks, basins,urinal etc as in repair complete all as specified and directed.

S&F 3-in-1 wall mixer for Hot & Cold water supply with telephonic shower arrarengement, brass chromium plated fancy type, screwed down for 15mm bore iron pipe incl necessary fittings & fixtures etc.as in repair complete all as specified and directed.

S&F Central hole for Hot and Cold water supply basin mixer, brass chromium plated screwed down for iron pipes,including necessary fittings etc as in repair , complete all as specified and as directed.

S&F Kitchen sink mixture with regular swinging spout (wall mounted model) chromium plated screwed down for iron pipes,including necessary fittings etc as in repair complete all as specified and as directed.

S&F Stainless Steel Sink with Drainage Board l.0mm thick Overall size 915mm x 460mm and Bowl size 410 mm x 355 mm x 165 mm for Kitchen or Laboratory with Plugs, Washers, Brass chromium plated Waste Fitting 32mm dia, PVC waste pipe, a Pair of Cast Iron Brackets duly Painted including Cutting and Pinning in Ends, making good disturbed Surfaces in Cement Mortar 1:3 including Taking down/out unserviceable Sink and connected Items, complete all as specified and as directed.

S&F in repair stainless steel utencil plate rack (size 900 x 1200 x 200 mm) using 1.0mm thick sheet with all fittings accessories complete as directed.

S&F Vitreous China Colour Wash down Water Closet Pan (Pedestal Pattern) with "p" or "s" trap front or back inlet including fixing Bolts with and excluding 10 litre capacity low level Flushing Cistern matching with water closet colour with inlet ball valve float handle and providing 32mm dia PVC flush pipe including plastic water closet seat with flat bottom cover (coloured) fixed with mild steel chromium plated or aluminium hinging device including taking down old unserviceable one complete all as specified and as directed.

S&F in repair Vitreous China White Squatting Pan ‘ORISSA’ Pattern, size 580x440mm with ‘P’ or ‘S’ Trap, Integral Foot Rest, providing Joints between Flush Pipe and Socket of WC Pan including Flushing Cistern and Flush Pipe, fixing with and including provision of cement Concrete Bedding complete all as specified and as directed.

S&F Vitreous China Wash Hand Basin 550x400mm in size, White (Flat Back or Angle Back Type) with 32mm dia Brass Chromium Plated Waste Fitting, a pair of Cast Iron Brackets duly painted including Cutting and pinning in Ends, making good disturbed Surfaces in Cement Mortar 1:3 including taking down/out unserviceable Wash Hand Basin and connected Items, complete all as specified and as directed.

S&F Brass chromium plated fancy type bib cock screwed for 15 mm bore of pipe etc. as in repair complete all as specified & directed.

S&F Brass chromium plated fancy type stop cock screwed for 15 mm bore of pipe etc.incl necessary fittings & fixtures as in repair complete all as specified & directed.

S&F Two way bib cock with flange brass chromium plated fancy type screwed for 15 mm bore etc.as in repair complete all as specified and as directed.

S&F Angular Stop cock concealed type ,15 mm dia cast copper alloy chromium plated fancy type with wall flange screwed for iron pipe etc. as in repair complete all as specified and directed.

S&F 125 mm dia brass chromium plated shower rose with or without swivels joint for fixing to 15 mm bore pipe etc complete including taking down old one complete all as specified and directed.

Supply and fixing in repair 10 litre capacity low level PVC flushing cistern (any colour), syphonic action type, with inlet, ball valve, float, handle, fixed with cast iron bracket (of suitable size) and providing 32 mm dia PVC flush pipe and making all necessary connections complete as directed.

S&F cast copper alloy health faucet with chomium plated with flexible cord fixed on wall screwed down for iron pipes,including necessary fittings etc as in repair complete all as specified and as directed.

S&F in repair plastic seat and cover white for EWC with flat bottom including hanging device complete all as specified and as directed.

S&F Towel ring of size 150mm dia decorative type fixed with walls including necessary fittings etc as in repair complete all as specified and as directed.

S&F Brass chromium plated tubular towel rail, 20mm dia, D type, 60,cm long between flanges as in repair complete all as specified and directed.

S&F Toilet paper holder of brass chromium plated fixed to walls with chromium plated brass screw including necessary fixing arrangement as in repair complete all as specified and directed.

S&F Chromium Plated soap dish fixed to wall with necessary fixing arrangement as in repair complete all as specified and directed

S&F Glass shelf assembly consisting of 5.5 mm thick sheet glass self 19-12 cm wide, 60 cm long with chromium plated brackets guard and railing fixed in position with necessary fixing arrangement as in repair complete all as specified and directed.

S&F Glass corner shelf of single set with chromium plated brackets and railing including necessary fittings and fixture as in repair complete all as specified and directed.

S&F Chromium plated bottle trap ( with internl partitions) 32mm size with 250mm long wall connection including wall flange fixed in position with necessary fixing arrangement as in repair complete all as specified and directed.

S&F Chromium Plated waste coupling heavy grade full thread 32mm (brass) fixed to stainless steel sink including necessary fixing arrangement as in repair complete all as specified and directed.

S&F PVC connection pipe 15mm size with PTMT nuts of length 600mm long as in repair complete all as specified and directed.

S&F Chromium Plated Connector pipe for hot water supply of size 600 mm long fixed to 15 mm dia GI pipe with brass nut and spanner including necessary fixing arrangement as in repair complete all as specified and directed.

Supply and fix Gun metal, globe or gate valves (ISI marked) ( Class-I) with iron wheel head, screwed both ends for 20 mm bore GI pipe including taking down old unserviceable one complete as specified and as directed

S&F Stainless steel peg set assembly for 6 hook fixing on door or wall with the help of screw as in repair complete all as specified and directed.

S&F Chromium Plated Telepohne shower with connector pipe & wall hook as in repair complete all as specified and directed.

S&F 600 mm long CP towel rack with lower hanger including complete fittings and fixtures etc as in repair complete all as specified and directed.

Cleaning of blocked kitchen trap / nahani trap / floor trap/ Water closet of any type / pattern with vaccum pump upto 1st manhole and making the drain channel fully functional by flushing with sufficient quantity of water to entire satisfaction of Engineer-in-Charge including cleaning of 1st manhole and removing the waste materials / sludge etc to a distance outside residential area and burying the same in a pit and spreading bleeching powder surrounding the area @ 1Kg/ Sqm and sealing the top with fine sand of suitable depth complete all as specified and as directed. Note:-(i) Cost of earth work in excavation required for digging the borrow pit and burrying the the waste materials / sludge in the borrow pit and sealing the pit with fine sand and spreadind of bleeching powder shall deemed to be included in the rate quoted. (ii) Any damged done by the Contractor during cleaning shall be make good by the Contractor at his own cost upto the satisfaction of Enginner-in-Charge.

Cleaning & removing of air lock in GI pipe from outlet and making the water supply available upto bib tap, pillar tap, wall mixer, basin mixer, concealed stop cock, angle valve in water supply lines of size 15 mm dia including taking down (if necessary) and re-fixing the same in position make the all system fully functional to the entire satisfaction of E-i-C complete all as specified and directed. Note for item Nos 93.00 to 96.00:- Unit rate quoted by tenderer shall included for use of all scaffolding, trestles, ladders, cradles etc, hoisting, lowering and protective measures etc up to twelve storeys height of bldgs.

All as per item No. 94.00 above but water supply line of size 20mm dia

All as per item No. 94.00 above but water supply line of size 25mm dia

Repair for joint leakage in steel water tube by replacing of GI elbow/reducer/socket/union/bend/tee/nipple of any size/ bore medium grade ISI mark complete all as directed. Note: 1. Unit rate quoted by tenderer shall included for use of all scaffolding, trestles, ladders, cradles etc, hoisting, lowering and protective measures etc up to twelve storeys height of bldgs. 2. Cost of taking down steel water tube & refixing old steel water tube and connection in new or old position with new fixing arrangment in walls, ceiling, floors etc for replacement of worn out/defective GI fitting shall be included in the rates quoted by the contractor

M&L in repairs for leaking water in brass/CP bib tap, pillar tap, concealed stop cock, angle valve of any make/ description/size in any position by replacing the (brass spindle+brass jumper washer + CP Wall Flange) ,tightening of fittings etc ,also removing air lock, blockage in water pipe line & make the all system fully functional to the entire satisfaction of Engr-in-Charge complete all as specified and directed

M&L in repairs for leaking water in brass/CP Wall Mixer, basin mixer, sink mixer of any make/ description/size in any position by replacing the brass spindle & washer, tightening of fittings etc ,also removing air lock, blockage in water pipe line & make the all system fully functional to the entire satisfaction of Engr-in-Charge complete all as specified and directed

M&L in repairs for (PVC Syphon assembly (internal kit) for any type/size/make of low level flushing cistern,tightening of fittings etc & make the all system fully functional to the entire satisfaction of Engr-in-Charge complete all as specified and directed.

S & F in repair 100mm dia stainless steel grating with hole/without hole for waste pipe fixed over floor/nahani trap complete all as specified and directed

S & F in repair 125mm dia chromium plated grating with hole/without hole for waste pipe fixed over floor/nahani trap complete all as specified and directed.

Repair to any type of iron door works of shutters, of any description in any situation by taking down and replacing of damaged iron protion and fixing the same opening including Resecuring, easing, adjusting, refixing builders hardware butt hinges, tower bolts, handles, sliding door bolts, wiremess, in same/other position, renewal of screws, welding (if required) & tightening of GI/steel wiremesh etc making smooth functioning (for proper closing, opening) etc and applying paint over welded protion to match with remaining protion wtih entire satisfaction of Engieer-in-Charge complete all as specified and directed.

M&L for cleaing of floor and wall existing surfaces, sanitary fittings etc with the help of Nirma poweder / harpic/ acid complete all as specified and directed.

Taking down and refixing of bid tap, angular stop cock etc including taflon tape, extenstion short piece complete all as specified and as directed.

Taking down and refixing of wall mixture, basin mixture, sink mixture including taflon tape, extension short piece etc complete all as specified and as directed.

Taking down and refixing of corner shelf, glass shelf, mirror towerl rail and towel ring, toilet paper holder, soap dish etc including bullets and screw complete all as specified and as directed

Taking down and refixing of western type commode including screw white cement complete all as specified and as directed.

Taking down point wiring (light, fan, socket and power complete including fixtures and fittings such as switches ceiling roses, pendents , regulators, sockets, light fittings etc. removing materials to store for keeping in safe custody for refixing or for taking credit (credit for above items should be made as per conditions separately) and making good distrubed surfaces of walls, floors, etc. including cleaning all and specified and directed.

M&L for point wiring with PVC insulated unsheathed stranded copper conductor cable of size 1.5 Sq mm FRLH/S in and including concealed PVC conduit 20 mm dia medium duty ISI marked with all necessary fittings with sunken cast iron /pressed steel terminal box ,flush to surface of 1.6mm wall thickness and 3 mm thick laminated sheet top cover for mounting switches including 1.5 sq mm FRLH/S PVC insulated unsheathed stranded copper conductor as earth lead and connected to common earth doly for one light / ceiling fan/exhaust fan/bell controlled by one switch complete including cutting, chasing the surface and then making good the same in CM 1:3 to finishing the match surface complete all as specified and directed by Engr- in-charge.

All as per item No.110.00 mentioned here-in-before but 3 pin 5 amps socket out let point same board with other switches of cables of 1.5 sqmm

All as per item No.110.00 mentioned here-in-before but for one 5 amp switch socket combination on independent board with cables of 1.5 sqmm size

All as per item No.110.00 mentioned here-in-before but using 2.5 sq mm size stranded copper conductor cable for one 16 amp switch socket outlet on independent board including 2.5 sq mm FRLH/S PVC insulated unsheathed stranded copper conductor as earth lead and connected to common earth doly complete all as specified and directed by engineer incharge.

M&L for point wiring with PVC insulated unsheated stranded copper conductor cable FRLH/S of size 1.5 sq mm in and including PVC casing caping of required width with all necessary fittings with sunk cast iron /pressed steel terminal box of1.6mm wall thickness and 3 mm thick laminated sheet top cover for mounting switches including 1.5 sq mm FRLH/S PVC insulated unsheathed stranded copper conductor as earth lead and connected to common earth doly for one light / ceiling fan/exhaust fan controlled by one switch, one way complete all as specified and directed by Engineer incharge.

All as per item No.114.00 mentioned here-in-before but 3 pin 5 amps socket out let point same board with other switches of cables of 1.5 sqmm

All as per item No.114.00 mentioned here-in-before but for one 5 amp switch socket combination on independent board with cables of 1.5 sqmm size

All as per item No.114.00 mentioned here-in-before but using 2.5 sq mm size stranded copper conductor cable for one 16 amp switch socket outlet on independent board including 2.5 sq mm FRLH/S PVC insulated unsheathed stranded copper conductor as earth lead complete all as specified and directed by Engineer-in-Charge.

All as per item No.114.00 mentioned here-in-before but using 4 sq mm size stranded copper conductor cable for one 16 amp switch socket outlet on independent board or for AC Starter including 4 sq mm FRLH/S PVC insulated unsheathed stranded copper conductor as earth lead complete all as specified and directed by Engineer-in-Charge.

S&F lamp holder insulated body with back plate for batten fittings complete all as directed.

S&F in repair lamp holder insulated body with back plate for batten fittings complete all as directed.

S & F switch piano modular flush type 5/6 Amps 230V AC one way complete all as specified and directed by Engineer-in-Charge.

S & F in repair switch piano modular flush type 5/6 Amps 230V AC way complete all as specified and directed by Engineer-in-Charge. Make: Indo Asian Cat Part No.800000 or equivalent as per list of makes.

S & F in repair switch piano modular flush type 6/10 Amps two switch for two way 230V AC complete all as specified and directed by Engineer-in-Charge. Make: Indo Asian Cat Part No.800001 or equivalent as per list of makes.

S&F modular socket outlet 3 pin 5/6 Amps 230 volts 1 module flush type. complete all as specified and directed by Engineer-in-Charge.

S&F in repair modular socket outlet 3 pin 5/6 Amps 230 volts 1 module flush type complete all as specified and directed by Engineer-in-Charge. Make: Indo Asian Cat Part No.801800 or equivalent as per list of makes.

S & F switch piano modular flush type 16 Amps 230V AC complete one way 1 module complete all as specified and directed by Engineer-in-Charge.

S & F in repair switch piano modular flush type 16 Amps 230V AC complete one way 1 module complete all as specified and directed by Engineer-in-Charge. Make: Indo Asian Cat Part No.800002 or equivalent as per list of makes.

S&F modular bell push flush type 5 Amps 1 module complete all as specified and directed by Engineer-in-Charge.

S&F in repair modular bell push flush type 5 Amps 1 module complete all as specified and directed by Engineer-in-Charge. Make: Indo Asian Cat Part No.800007 or equivalent as per list of makes.

Fixing only modular one/ two way switches, socket outlet and bell push of 1 module and of any capacity complete all as specified. Note:- Serviceable switches and socket outlet shall be obtained from from taking down item mentioned here-in-before.

S&F modular switch socket outlet multipurpose 3 pin 6/16 Amps 2 modulecomplete all as specified and directed by Engineer-in-Charge.

S&F in repair modular switch socket outlet multipurpose 3 pin 6/16 Amps 2 module complete all as specified and directed by Engineer-in-Charge. Make: Indo Asian Cat Part No.800002 & 800022 or equivalent as per list of makes.

S& F modular electronic step type fan regulator by step type 230 volt 2 module complete all as specified and directed by Engineer-in-Charge.

S& F in repair modular electronic step type fan regulator by step type 230 volt 2 module complete all as specified and directed by Engineer-in-Charge. Make: Indo Asian Cat Part No.800043 or equivalent as per list of makes.

Fixing only modular switch socket outlet and fan regulator of 2 module and of any capacity complete all as specified. Note:- Serviceable switch socket outlet and fan regulator shall be obtained fromfrom taking down item mentioned here-in-before.

S&F call bell, ding dong AC 230 volt single pole (ding dong type) complete all as specified and directed by Engineer-in-Charge.

S&F in repair call bell, ding dong AC 230 volt single pole (ding dong type) complete all as specified and directed by Engineer-in-Charge.

S&F ceiling rose surface bakelite 65x50mm single phase complete all as specified and directed by Engineer-in-Charge.

S&F in repair ceiling rose surface bakelite 65x50mm single phase complete all as specified and directed by Engineer-in-Charge.

S&F switch socket combination with box 2in 1 3 pin 6 Amps 230 volts flush type complete all as specified and directed by Engineer-in-Charge.

S&F switch socket combination with box multipurpose 3 pin 10 and 20 Amps one switch complete all as specified and directed by Engineer-in-Charge.

Fixing only swithes, switch socket combination, ceiling rose, call bell and lamp holder of any capacity complete all as specified. Note:- Serviceable swithes, switch socket combination, ceiling rose, call bell and lamp holder shall be obtained from from taking down item mentioned here-in-before.

Supply and fixing LED lights fitting 1x 20W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed by Engineer-in-Charge.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engineer-in-Charge.

S & F LED bulb 9Watts 240V 50Hz 6500K b22 base in bulb holder complete all as specified and directed by Engineer-in-Charge.

Supply and fix Decorative wall light fixture made up of Polycarbonate, suitable for 9 W retrofit LED Lamp B22 base complete with all the connection complete all as specified and directed by Engineer-in-Charge.

Supply and fix plug top 3 pin16A 240V Easy to carry, Non flammable & Durable Heavy duty , nickel plated brass terminals Long lasting polycarbonate plastic material complete all as specified and directed by Engineer-in-Charge.

S&F in replacement plug and socket in sheet metal enclosures with two pin and earth plug and socket complete with and including MCB SP 20 Amps 240 volts heavy duty all as specified and as directed by Engr-in-charge.

S&F A C starter unit consisting of one 25 Amp capacity starter, one 240 V 25 Amps 10 KA SPN MCB, one 25 Amps socket and one 25 Amps plug top prewire complete all as specified and directed by Engineer-in-Charge.

S&F in repair A C starter unit consisting of one 25 Amp capacity starter, one 240 V 25 Amps 10 KA SPN MCB, one 25 Amps socket and one 25 Amps plug top prewire complete all as specified and directed by Engineer-in-Charge.

S&F sunken flush metal GI boxes for fixing of modular switches/sockets flush to the walls complete for 2 modules including taking down of old unsv one complete all as specified and directed by Engineer-in-Charge.

All as per item No.151.00 mentioned here-in-before but for 3 modules

All as per item No.151.00 mentioned here-in-before but for 6 modules

All as per item No.151.00 mentioned here-in-before but for 8 modules

S&F modular cover plate with frame for fixing of modular switches/sockets complete for 2 modules complete all as specified and directed by Engineer-in-Charge.

All as per item No.155.00 mentioned here-in-before but for 3 modules

All as per item No.155.00 mentioned here-in-before but for 6 modules

All as per item No.155.00 mentioned here-in-before but for 8 modules

Taking down unserviceable rusted / damaged MCB DBs of any type and way along with any type MCB and keeping serviceable MCB in safe custody in re-use in the work and making good to the distubed surfaces of walls etc. complete all as specified and as directed.

S&F MCB TPN DB made up with sheet metal, phosphorised, power coated, neutral link, earth bar and din rail, 8 way TPN with 200 amps rated bus bar, 415 volts complete all as specified and as directed.

S&F sheet metal enclosure for DB's when MCBs to be used 8 way single pole and neutral double door with 200 amps rated bus bar complete including connection all as specified.

S&F isolator 63 Amps 415 Volts FP with rapturing capacity 10KA including taking down of old one complete all as specified and directed by Engineer-in-Charge.

S&F MCB 6 to 32 amps 240 volts 10KA single pole complete all as specified.

Fixing only MCB 6 to 32 amps 240 volts 10KA single pole complete all as specified. Note:- Serviceable MCBs shall be obtained from ifrom taking down itemof MCBs/DBs mentioned here-in-before.

S&F in repair MCB 6 to 32 amps 240 volts 10KA single pole complete all as specified.

S&F MCB DP 40 to 63 amps 240 volts 10KA breaking capacity complete all as specified.

Fxing only MCB DP 40 to 63 amps 240 volts 10KA breaking capacity complete all as specified. Note:- Serviceable MCBs shall be obtained from taking down itemof MCBs/DBs mentioned here-in-before.

S&F in repair MCB DP 40 to 63 amps 240 volts 10KA breaking capacity complete all as specified and directed by Engineer-in-Charge.

S&F sub main wiring two run of single core PVC insulated unsheathed stranded copper conductor of size 10 sqmm & one run of PVC insulated unsheathed stranded copper conductor of size 10 sqm as earth lead drawing into rigid non metalic PVC conduit of size 20mm dia including taking down old unsv complete all as specified. Note: Two run of 10 sqmm cable and one run of 10 sqmm cable will be measured as single length.

Taking down and opening out the ceiling fan/wall mounted upto1200/1400 mm sweep for inspection, removing bush / bearing, cleaning of bush / bearing, replacement of unserviceable / worn out bearing / bush, shaft, removing burnt out coils from the slots, cleaning and repairing of slots complete including materials like split pin, rubber reel etc and reassembling and refixing of fan complete with and including minor Spares, if any required complete all as specified and as directed. Note : Spare parts shall be measured & paid separately.

Rewinding of ceiling fan motor with super enamelled copper winding wire of suitable size & varnishing including testing of fan after rewinding complete all as specified.

Supply only ball bearing suitable for 1200/1400mm sweep Ceiling fan of any make.

Supply only capacitor of 2.5 mfd for Ceiling Fan

Supply only gun metal bush of suitable size for ceiling fan of sweep 1200mm/1400mm as per existing one complete.

Supply only shafts for ceiling fan suitable for 1200mm sweep

Supply only PVC connector for Ceiling Fan

Supply only fan blades for Ceiling fan suitable for 1200mm sweep/1400mm sweep.

Supply only nuts, bolts, for Ceiling fan

M&L for painting of ceiling fan/wall fan/exhaust fan of any size and sweep complete with synthetic enamel paint by spraying including filling with cavities with filler, after cleaning all dust etc complete all as specified and directed by Engineer-in-Charge.

Taking down and opening out the exhaust fan upto 400 mm sweep for inspection, removing bush / bearing, cleaning of bush / bearing, replacement of unserviceable / worn out bearing / bush, shaft, removing burnt out coils from the slots, cleaning and repairing of slots rubber reel etc. reassembling and refixing of fan complete including all as specified and as directed.

Rewinding of fan motor with super enamelled copper winding wire of suitable size & varnishing including testing of fan after rewinding complete all as specified.

M&L for painting of exhaust fan of any size and sweep complete, in situ with approved colour synthetic enamel paint by spraying including filling with cavities with filler, one coat after cleaning all dust etc.

Supply only bush suitable for exhaust fan.

Supply only ball bearing suitable for exhaust fan.

Supply only capacitor 2.5 mfd for exhaust fan.

Taking down carefully unserviceable geyser of any type and make from site after disconnections of water & electrical connections & carrying out to MES store yard for inspection and thereafter to workshop for repair & replacement of components such as heating element, thermostate, cable, neon lamp, plugtop, outer casing, plates & repair work to apparatus plate, copper tank,split plate including de-scaling of water tank etc and carrying back to MES store yard for testing and refixing at site and making water & electrical connection on completion and all as directed.

M&L for painting of geysers 25 ltrs at site/at workshop duly with one coat of synthetic enamel paint (white) including preparation of surfaces with brush, cleaning agents as required of 25 Ltr capacity and its front with best quality paint all as directed and specified by Engr-in-Charge

M&L for brazing/gas welding of inner container copper of 25 ltrs /50 ltrs capacity and any make and making leak proof all as directed.

Supply only following spares for geysers:- Heating element 1.5KW including rubber gasket ISI marked suitable for existing geysers.

Heating element 2.00KW including rubber gasket ISI marked suitable for existing geysers.

Thermostate for suitable existing geyser of 25/50 litrs capacity

Chromium plated copper pipe of length not less than 60cm including washers for incoming & outgoing hot & cold water connections as specified and directed by Engr-in-charge

Apparatus plate assembly complete for geyser of capacity 25/50 litrs capacity.

Outer casing made out of 22 SWG MS sheet suitable for geyser of capacity 25 litrs.

Storage tank fabricated from copper sheet gauge suitable for geyser of capacity 25 ltrs of make as specified and approved.

Split plate bottom cover made out of 22 SWG MS sheet suitable for 25 litrs capacity geyser

Split plate top cover made out of 22 SWG MS sheet suitable for 25 litrs capacity geyser

Insulating material glass wool

Element holding brass stud

Element holding MS clamp

Fusible metal plug

Neon lamp round/square with connection lead

Non return valve for geyser inlet

Brass Pressure Reducing valve for geysers 25 ltrs as per site requirement. NOTE FOR ALL ITEMS OF BOQ:- All retrived servicable and un-serviceable materials shall be deposited in MES store yard and handed over to contractor, if catered for in Schedule of credit.

UNIVERSAL TRADING CENTRE (BID ID -3419744)

PINKY CO. (BID ID -3418127)

SPECIAL CONCRETE AND CONSTRUCTION CO. (BID ID -3422094)

MS HORIZEN (BID ID -3418863)

RUNGTA STEEL CORPORATION (BID ID -3422419)

SRI BHOOMIJ INFRAPROJECTS & SERVICES LLP (BID ID -3420052)

DGR CONSTRUCTION (BID ID -3422440)