Special repair for renovation of Sub Health Centre at village Kathleri in Karnal Distt.

Amount

Earth work in excavation in foundations, trenches, etc. in all kinds of soils, not exceeding 2 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil, clear from the edge of excavation and subsequent filling around masonry, in 15 cm layers with compaction, including disposal of all surplus soil, as directed within a lead of 30 metres.(HSR 6.6)

Dismantling Brick Work, Tile Masonry or Tile Lining and Tile Terracing (b) in cement (HSR 8.5 (b)

Dismantling cement conglomerate/ terazzow floors 25mm to 50 mm thick incliding concerete base. (HSR 8.25)

Scraping (a ) cement plaster (HSR 8.32)

Cement concrete 1:4:8 with brick ballast 40mm nominal size in foundation and plinth (HSR 10.36)

Cement concrete 1:4:8 with stone aggregate 20mm nominal size in foundation and plinth. (HSR 10.38)

Cement Concrete 1:4:8 with stone aggregate 40mm nominal size in foundation and plinth. [HSR 10.39]

Cement concrete 1;2;4 with stone aggregate 20mm nominal size in first storey upto 4 metres above plinth level (HSR 10.59)

Cement Concrete 1:1½:3 with stone aggregate 20mm nominal size in first storey upto 4 meters above plinth level. [HSR 10.60]

Cement concrete 1 : 1½ : 3 with stone aggregate 20 mm nominal size for reinforced concrete work in slabs with inclination not exceeding 25 degree with horizontal, excluding steel reinforcement, but including centring and shuttering, laid in position, complete in all respects. [HSR 10.82 + 10.95 (a)]

Damp proof course 25mm thick of cement concrete 1:2:4 using stone aggregate without 2 coats of bitumen coat. [HSR 10.115 (-) Note]

Pvg & Laying 60 mm thick interlocking paver block of all shapes and colours in design mix cement M -35 over a bed of 25 mm thick fine sand complete in all respect. (HSR 10.158)

First class brick work laid in cement sand mortar 1 : 6 in foundation and plinth (HSR 11.2)

First class brick work laid in cement sand mortar 1:4 in foundation and plinth. (HSR 11.4)

First class brick wrok in cement mortar 1:4 in super structure (HSR 11.9)

Terracing consisting of tiles 22.86 cm x 11.43 cm x 3.81 cm laid over 87.50 mm mud filling on a layer of 25 mm mud plaster and another layer of mud mortar for laying the tiles, including two coats of btumen laid hot at 1.654 kg per sqm on top of R.C.C slab including grouting with cement sand mortar 1:3 and top surface to be left clean etc. (HSR 13.13)

Providing and fixing PVC rain water pipe 6 Kg. Pressure of ISI mark in cement mortar during masonry work. a) 100mm dia PVC pipe 6 Kg. pressure. (HSR 13.89 a)

Providing & fixing PVC bend ISI mark. a) 100mm dia PVC Bend. (HSR. 13.90 a)

Providing and fixing vitrified tiles of size 600 x 600mm of approved make in flooring laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT, JOHNSONS & RAK. (HSR 14.89)

Providing and fixing vitrified tiles of size 600 mm x 600mm of approved make in skriting / dado laid in any pattern as specified over base of 12mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT, JOHNSONS & RAK. (HSR 14.90)

Providing and fixing ceramic tiles / anti skid tile of size 400 mm x 400mm or above size of approved make in flooring, laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles. Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT, RAK & JOHNSON. (HSR 14.91)

Providing & fixing 1st quality ceramic glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manufacturer) of approved make in all colors, shades except burgundy, bottle green, black of any size as approved by Engineer-In-Charge in skirting, risers of steps and dados over 12mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry, including pointing in white cement mixed with pigment of matching shades complete. (HSR 14.92) b) Size of ceramic Glazed tiles 300 x 450 mm

12 mm thick cement plaster 1 : 4 on walls ( HSR 15.5 )

15mm thick cement plaster 1:4 on the rough side of single or half brick wall. (HSR 15.10)

Painting two coats with synthetic enamel paint in all shades on old wood-work or metalic or plastered or concrete surfaces to give an even shade including rubbing down old paint. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.5)

Preparation of plastered or concrete surfaces for painting, including sand papering the surface, applying one coat of linseed oil and filling with approved quality filler, consisting of white lead, linseed, varnish and chalk mitti including finishing surface to the required finish, complete. (HSR 16.24)

Applying priming coat with cement primer in all shades on newly plastered or concrete exterior surface. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.25).

Distempering with washable oil bound distemper(of approved manufacture) two coats on old distempered work. (HSR 16.60)

Finishing walls with exterior decorative cement based paints such as snowcem, Robbiacem etc. on new work, two coats to give an even shade (HSR 16.61)

Providing two coats of exterior acrylic emulsion paint. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). [HSR 16.79 (b)].

Providing and applying two coats white cement based putty over plastered surface and grindling the surface smooth with sand paper to get an even and smooth finish including cost and carriage of all material, labour charges, scaffolding, sundries etc. complete. (Note:- reputed make Putty such as J.K./ Birla shall be used as approved by Engineer-in-charge). (HSR 16.81).

Factory manufactured wire gauze door and window shutters of commercial hard wood, such as hollocks, champ, chikrassy and chaplash, etc., (non-coniferous timber other than teak, conforming to I.S. specification No. 1003, kiln seasoned), with 100 mm wide vetical styles, 150 mm wide lock rail, 200 mm wide bottom rail and wire gauze of 140G or 120G designation including cost of iron hinges, screws, chocks/cleats,stops, nails etc., complete fixed in position (execluding the cost of any fittings, other than specified above but including labour for fixing the same in position) [HSR 17.92 (-)Note (i) under item No. 17.18] ii) 35 mm thick.

Wrought iron and mild steel(using angles, flats ,square bars , tees and channels) ladders, grills, gratting frames, window guards, iron doors openable or fixed stair case or parapet or any other type of railing, gates and tree guards etc., including cost of screws and welding rods or bolts and nuts complete fixed in position (HSR 18.12)

Steel reinforcement TMT bars FE-500 FQR /FE-500 D grade or more for RCC work, where no included in the complete rate of RCC including straightening, bending vinding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. and placing in position complete in all respects for all heights/depths/storeys/basements etc. (HSR 18.22)

Pressed steel sheet frames (chowkats ), consisting of 2mm thick steel sheet of the specified section,including iron lugs(hold fasts) iron hinges conforming to P.W.D. specifications, including bolts for fixing stops, locknotch, provision for receiving tower bolts, and finished with one coat of ready mixed paint red lead non-setting primer, of approved quality, fixed in position including the cost of cement concrete 1:3:6 for fillings in the frame, and cement concrete 1:3:6 for lugs complete (HSR 18.34) a) Door and Window frame of size 89 mm x 50 mm with 40 mm wide single rebate

c) Door and Window frame of size 127 mm x 50 mm with 40 mm wide double rebate

Preparation of sub grade, including trenching, rough dressing of spoil, final dressing of earth, to given levels and camber, watering rolling with road roller, and compacting the bed. [HSR 24.1] LR

Providing and fixing in position best Indian make ( to the approval of the Engineer-in-Charge) Indian type Orissa or Orya water closet suite for sinking into floor, with raised foot treads complete with 100mm H.C.I. 'P' trap with or withoput vent as required and all other necessary fittings as fully described in item no. 30.1 above [HSR 30.2 a(i)] a) Size 580mm (i) white

Providing and fixing in position best indian make (as approved by the Engineer-in-Charge) European type water closet suit with non-concealed 'P' or 'S' trap with or without vent and all other necessary fittings as fully described in item no. 30.3 above [HSR 30.4 (i)] White

Providing and fixing in position best indian make (as approved by the Engineer-in-charge) European type water closet suit, Syphonic type, consisting of- (i) Vitreous China Ware Syphonic Suite with 15 Liters capacity matching chinaware cistern and all internal brass fittings complete with ‘P’ or ‘S’ trap with or without vent (as approved by the Engineer-in-charge). (ii) One Piece seat and lid in hollow black or white with plastic fitted with chromium plated hinges and rubber buffers,(to the approval of the Engineer-in-charge). Complete in all respects including cutting and making good the walls and floors [HSR 30.5] a) Single trap syphonic W.C. Suite (i) white

Extra over item Nos. 30.1 to 30.4 and 30.6 for providing and fixing 15 litres capacity low level vitreous china ware cistern complete with flush bend all other necessary fittings instead of C.I. High level cistern complete with fittings. [HSR 30.12 (i)] White

Extra over item Nos. 30.3 to 30.6 for providing and fixing best Indian make plastic hygenic seat with lid complete instead of hollow black or white plastic seat and lid. [HSR 30.13 (i)] White plastic seat (Solid)

Providing and fixing in position 15mm i/d C.P. brass bib cocks of best quality (as required by the engineer-in-charge). (HSR 30.75 )

Providing and fixing in position C.P. brass stop cocks (as approved by the Engineerin- charge) (HSR 30.76 (a)

Providing and fixing in position best quality stainless steel sinks with complete fittings as fully described in item No.30.51 above [HSR 30.53] (a) size 600mm x 450mm x 200mm

Providing and fixing in position best Indian make (ordinary)lavatory suites, consisting of Lavatory in vitreous chinaware size as given below (to the approval of the Engineer-in-charge) including china plug for tap hole where necessary. R.S. or C.I. Brackets for building into wall including painting, 32mm C.P. brass waste with C.P brass chain and rubber plug, 15mm C.P. brass screw down pillar tap with jamnuts or couplings best design (as approved by the Engineer-in-Charge). All fittings best Indian make and; to the approval of the Engineer-in-Charge. All brass work chromium plated and complete in all respect including cutting and making good the walls floors and painting of fittings etc. [HSR 30.41] White (i) Size 450mm x 300mm with one tap.

Providing and fixing HDPE water storage tanks of Sintex, Diplast, O.K., Supreme make with covers / lids marked with IS: 12701 on roof top of buildings including cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing overflow and scour provisions with sutiable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks complete in all respects to the satisfaction of Engineer-in-Charge. (except civil work). (HSR 30.119) 1000 Ltr. capacity.

Providing & fixing 2mm thick PVC Sheet for shed with complete fitting from cover including angle, nut, bolts, paints, pipe excavation of earth work, concrete for foundation etc. complete in all respect to the entire satisfaction of Engineer-in-Charge. ( N.S) Note:- 1. In case of any difference in the unit & nomenclature of any of the HSR Items of Civil, P.H. work depicted in this DNIT and that given in HSR, the unit and nomenclature given in HSR shall be applicable. 2. Only reputed make material will be used (make/brand exhibited in HSR and exhibited in approved standard document) as approved by Engineer-in-charge, while executing various items/works at site.

The Adhmi Coop Society Ltd