Renovation and face lifting to the Commune Panchayat Kalyanamandapam at Kurumbagaram in Nedungadu Commune.

Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer-in-charge. - Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Chipping of unsound / weak concrete material from slabs, beams , columns etc. with manual Chisel and / or by standard power driven percussion type or of approved make including tapering of all edges , making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of Engineer-incharge- 50 mm average thickness

Cleaning of reinforcement from rust from the reinforcing barsto give it a total rust free steel surface by using alkaline chemical rust remover of approved make with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washing with water and allowing it to dry , all complete as per direction of the Engineer-incharge- Bars upto 12mm diameter

Providing , mixing and applying bonding coat of approved adhesive on chipped portion of RCC as per specifications and direction complete in all respect - Epoxy bonding adhesive having coverage 2.20 sqm /kg of approved make

Centering and shuttering including strutting , propping etc and removal of form for - Columns , Pillars , Piers , Abutments , Posts and Struts

Centering and shuttering including strutting , propping etc and removal ofform for - Lintels , beams , plinth beams ,girders , bressumers and cantilevers

Reinforced cement concrete work in beams, suspended floors,roofs having slope up to 15degree landings , balconies , shelves, chajjas , lintels , bands , plain window sills , staircases and spiral stair cases above plinth level up to floor five level excluding the cost of centering ,shuttering, finishing and reinforcement , with 1:1.5:3 (1 cement : 1.5 fine aggregate : 3 graded stone aggregate 20mm nominal size)

Providing ,transporting, hoisting and fixing upto floor five level precast reinforced cement concrete in shelves including setting in cement mortar 1:3 (1 cement : 3 fine aggregate) , cost of required centering , shuttering and finishing with neat cement punning on exposed surfaces but excluding the cost of reinforcement , with 1:1.5:3 (1 cement : 1.5 fine aggregate : 3 graded stone aggregate 20 mm nominal size)

Steel reinforcement for R.C.C.work including straightening, cutting , bending , placing in position and binding all complete above plinth level - Thermo - Mechanically Treated bars Fe - 500D or more

Laying of Non - shrink free flow micro concrete Renderoc RG or equivalent in the proportion 1:1 (One Renderoc RG one graded stone aggregate of 12.5MM and below through the drilled holes till the voids and damaged area are completely filled and set to an average thickness of 50mm as directed by the Engineer in charge

Providing, mixing and applying SBR polymer (of approved make) modified Cement mortar in proportion of 1:4 (1 cement : 4 graded fine aggregate with polymer minimum 2% by wt.of cement used) as per specifications and direction. Note: Measurement and Payment : The Pre-meaurement of thickness shall be done just after the surface preparation is completed and payment under this item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding / tapping with a blunt metal instrument and / or the 75mm size cube crusing strength at the end of 28 days to be not less than 30 N / Sqmm) - 50mm average thickness in two layers

Providing wood work in frames of doors , windows, clerestory windows and other frames , wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately) -Vengai wood

Providing and fixing panelled or panelled and glazed shutters for doors, windows, and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately , all complete as per direction of Engineer-in-charge -(Note:- Butt hinges and necessary screws shall be paid separately) - Vengai wood - 35mm thick shutters

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors , windows and clerestory windows (area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick - Vengai wood

Providing and fixing ISI marked M.S. pressed butt hinges bright finished with necessary screws etc. complete - 125 X 65 X 2.12 mm

Providing and fixing ISI marked M.S. pressed butt hinges bright finished with necessary screws etc. complete - 100 X 58 x 1.90 mm

Providing and fixing aluminium sliding door bolts , ISI marked , anodised ( anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade , with nuts and screws etc complete - 300 X 16 mm

Providing and fixing aluminium sliding door bolts , ISI marked , anodised ( anodic coating not less than grade AC 10 as per IS: 1868), transparent or dyed to required colour or shade , with nuts and screws etc complete - 250 X 16 mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS :1868), transparent or dyed to required colour or shade , with necessary screws etc. complete - 300 x10 mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS :1868), transparent or dyed to required colour or shade , with necessary screws etc. complete - 100 x10 mm

Providing and fixing aluminium handles,ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade,with necessary screws etc, complete - 125 mm

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade,with necessary screws etc, complete - 75 mm

Steel work welded in built up sections / framed work, including cutting,hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required - in gratings, frames, guard bar, ladder, railings, brackets,gates and similar works

Cement concrete flooring 1:2:4 (1 cement : 2 fine aggregate : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete - 40mm thick with 20mm nominal size stone aggregate.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS:15622(thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved, in skirting, risers of steps and dados, over 12mm thick bed of cement mortar 1:3 (1 cement : 3 fine aggregate) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete

Providing and laying ceramic glazed floor tiles of size 300 x 300mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS :15622, of approved make , in all colours, shades, except white , ivory, grey, fume red brown, laid on 20 mm thick bed of cement mortar 1:4 (1 cement : 4fine aggregate), jointing with grey cement slurry @ 3.3 kg /sqm including pointing the joints with white cement and matching pigments etc., complete

Grouting the joints of flooring tiles having joints of 3mm width,using epoxy grout mix of 0.70kg of organic coated filler of desired shade (0.10kg of hardener and 0.20 kg of resin per kg) , including filling / grouting and finishing complete as per direction of Engineer-in-charge - size of tile 600x600 mm

Providing and laying rectified glazed ceramic flooring tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of Ist quality conforming to IS :15622, of approved make , in colours white, ivory, grey, fume red brown, laid on 20mm thick cement mortar 1:4 (1 cement : 4 fine aggregate) ,jointing with grey cement slurry @ 3.3 kg per sqm including grouting the joints with white cement and matching pigments etc., complete

Providing and fixing on wall face unplasticised rigid PVC rain water pipes conforming to IS: 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10mm gap for thermalexpansion,(i)Singlesocketed pipes - 110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings / accessories for unplasticised rigid PVC rain water pipes conforming to IS:13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm gap for thermal expansion - bend 87.5 degree - 110 mm bend

Providing and fixing on wall face unplasticised - PVC moulded fittings / accessories for unplasticised rigid PVC rain water pipes conforming to IS:13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm gap for thermal expansion - shoe (plain) - 110mm shoe

Providing and fixing unplasticised - PVC pipe clips of approved design to unplasticised- PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length, including cutting brickwork and fixing in cement mortar 1:4 ( 1 cement : 4 coarse sand) and making good the wall etc., complete - 110mm

Providing non-asbestos high impact polypropylene reinforced cement 6mm thick corrugated sheet (as per IS : 14871) roofing upto any pitch and fixing with pollymer coated J or L hooks, bolts and nuts 8mm dia. G.I. plain and bitumen washers or with self drilling fastener and EPDM washers etc., complete excluding the cost of purlins, rafters and trusses corrugated sheets and including cutting to size and shape wherever required.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer in- Charge) of total coated thickness 0.50mm (base metal of minimum 0.45mm thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

12mm cement plaster of mix -1:6 ( 1 cement : 6 fine aggregate)

Cement plaster 1:3 (1 cement : 3 fine aggregate) finished with a floating coat of neat cement - 20mm cement plaster

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc., complete

Applying one coat of water thinnable cement primer of approved brand and manufacturer on wall surface - water thinnable cement primer

White washing with lime to give an even shade- Old work (two or more coats)

Finishing walls with water proofing cement paint of required shade- Old work (one or more coats applied @ 2.20 kg /10 sqm) over priming coat of primer applied @ 0.80 litres/10sqm complete including cost of priming coat

Wall painting with plastic emulsion paint - Royal of approved brand and manufacture to give an even shade - two or more coats on new work

Finishing walls with premium apex ultima of required shade new work ( Two or more coat) applied @ 1.43 litr / 10 sqm @ 2.20kg / 10 sqm

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound) content - with ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than 50grams / litre

Painting wood work with deluxe multi surface paint of required shade. Two or more coat applied @0.90 ltr / 10sqm over an under coat of primer applied @ 0.75 ltr / 10 sqm of approved brand and manufacure

Painting steel work with deluxe multi surface paint to give an even shade. Two or more coat applied @ 0.90 ltr / 10 sqm over an under coat of primer applied @ 0.80 ltr / 10 sqm of approved brand and manufacture

Renewing glass panes, with putty and nails wherever necessary including racking out the old putty - Float glass panes of thickness 4mm (weight not less than 10kg/sqm)

Providing & fixing white vitreous china water closet squatting pan (Indian type) along with "S" or "P" trap including dismantling of old WC seat and "S" or "P" trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c malba all complete, as directed by the Engineer in Charge - Orissa pattern W.C.Pan of size 580x440 mm

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead - of area beyond 3 sqm

Demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as directed by the Engineer in Charge - in cement mortar

Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of - Asbestos Cement sheet

Supplying fixing and commisioning of 0.5 HP monoblock pumpset slow speed single phase motor. The rate include the cost of pumpset, pumpset fixing in position and test run etc.complete

Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps ,32 mm C.P.brass waste of standard pattern, including painting of fittings and brackets ,cutting and making good the walls wherever required - white Vitreous China wash basin size 630x450 mm with a single 15 mm C.P.brass pillar taps

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm or 340x410x265mm sizes respectively

Providing and fixing P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete - semi rigid pipe - 32mm dia

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with C.P.brass screws and washers complete

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, renching, refilling & testing of joints complete as directed by the Engineer in Charge - external work - 20mm nominal outer dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threadedfittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as directed by the Engineer in Charge - external work - 25mm nominal outer dia pipes

Providing and fixing C.P.brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms - 15 mm nominal bore

Providing and fixing on wall / column face unplasticed - PVC soil and waste pipes (type - B) conforming to IS : 13592- 1992 including jointing with seal ring conformation to IS : 5382 leaving 10mm gap for thermal expansion - single socked pipes -110mm diametre

Providing and fixing on wall face / column face unplasticised - PVC moulded fittings / accessories for unplasticisd - PVC soil and waste pipes conforming to IS:14735 - 1999 including jointing with seal ring conforming to IS :5382 leaving 10mm gap for thermal expansion - Single tee without door - 110 x110x110mm

Providing and fixing on wall face / column face unplasticised - PVC mould fittings / accessories for unplasticisd - PVC soil and waste pipes conforming to IS : 14735 - 1999 including jointing with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion -bend 110mm

Providing and fixing on wall / column face unplasticised - PVC soil and waste pipes (type B) conforming to IS :13592 - 1992 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - Single socketed pipes 75mm diameter

Providing and fixing on wall / column face unplasticisd - PVC moulded fittings / accessories for unplasticisd - PVC soil and waste pipes conforming to IS :14735 -1999 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - Single tee without door - 75x75x75mm

Providing and fixing on wall / column face unplasticisd - PVC moulded fittings / accessories for unplasticisd - PVC soil and waste pipes conforming to IS :14735 -1999 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - Bend 75 mm

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plith level - 1:5:10 (1 cement : 5 fine aggregate : 10 graded stone aggregate 40mm nominal size).

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 3.5 in foundation and plinth in - cement mortar 1:6 (1 cement : 6 fine aggregate)

Brick work with common burnt clay F.P.S (non modular) bricks of class designation 3.5 in superstructure above plinth level upto floor five level in all shapes and sizes in - cement mortar 1:6 ( 1 cement : 6 fine aggregate)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 3.5 in superstructure above plinth level upto floor V level - cement mortar 1:3 (1cement : 3 fine aggregate)

Earthwork in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as per direction of Engineer-in-charge , within a lead of 50m - all kinds of soil

Mazdoor Engaging labour for disposal of debries / bushes for the away from the site etc complete all as directed by the Engineer in charges

Providing and fixing of 65mm Navatal lock of 6 levers etc complete

Please Enable Macros to View BoQ information