8124 PROVISION OF HEAVY MATERIAL HANDLING EQUIPMENT STORAGE PARKING BAY AT C No 65 AT ND MBI ADDTN ALTN AND SPECIAL REPAIRS TO CHAIN LINK FENCING BARBED WIRE AND CONCERTINA COIL POST AND STRUT VIEW CUTTER AT NAVY HOUSE ADDN ALTN AND SPECIAL REPAIRS T

Amount

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out hard dense soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm complete all as specified and as directed.

PCC in foundation in 1:4:8 type D2 (40mm garded agg) in foundation filling and mass concrete complete all as specified and as directed.

M&L for PCC 1:3:6 type C1 (200mm garded agg) in plinth protection of 100mm thick at wall side and 75mm thick at other side complete all as specified and as directed.

Demolition of stone/brick masonry, built in cement mortar including all quoins, arches, pillars etc. but excluding ashlar facings dressed stone work and pre cast concrete articles complete all as specified and directed.

M & L for brick work with sub class 'B' bricks (old Size) straight or curved on plan exc 6 m mean radius and built in CM (1:6) complete all as specified and as directed..

Returning filling in including spreading levelling watering and well ramming in layers not exc 25 cm complete all as specified and as directed.

M&L for filling under floor with moorum laid in layers n.exc 15 cm thick spread ,levelled and rammed , watering and compacted complete all as specified and as directed.

M&L RCC 1:1.5 : 3 type B1( 20mm graded aggregate ) in lintel and plinth band over 1.5 span complete all as specified and as directed.

M&L mild steel TMT bars 10mm dia and over in reinforcement incl cutting bending and binding with mild steel wire annealed not less than 0.9 mm dia complete all as specified and as directed.

All as per item No. 9 above but 5mm dia and over upto and incl 10mm dia in stirrups complete all as specified and as directed.

S&F for rolled mild steel Sections of Grade Fe 410-W, (Gde- E-250) quqlity-A, as in post, runners, rafters, purlins steps etc fixed with connecting plates including bending, welding etc complete all as specified and as directed.

M&L for plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment Fe 410-W (gde E-250) complete all as specified and as directed.

Supply and fix structural steel framed works such as angle, channel etc. Confirming to Fe-290, E-165 as in supporting structure of duct, drain edge etc including making good the disturbed portion of concrete surfaces with 1:2:4 type B0 (using 12.5mm graded stone aggregate) complete all as specified and directed.

M&L for preparation of new steel surfaces exc 10 cm width or girth and applying two coats of synthetic enamel paints over a coat of red oxide primer complete all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge or thickness incl Nainital or similar pattern roof coverings all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated / Manglore pattern steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as complete all as specified and as directed.

M&L for 1.50mm thick galvanised shett as in valley gutter fixed with rivets with MS strip including clamp in both sides (MS clamp in MS flat iron patti or equivalent) or other suitable arrangement over MS bracket trapezoidal shape of required profile with desired slope etc complete all as specifided and as directed.

M&L 20 mm thick Granite (of any type) work (table rubbed and polished) as in steps, jambs, pillars, window- cills,cooking platforms, working table and like over 20 mm thick screed bed or bedding layer in cement mortar (1:4), including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed. Note: Colour of granite shall be approved by GE

M&L for 20 mm thick granite maching cut as in skirting/vertical surfaces i.e jambs /risers and pillars etc and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding, polishing and 10 mm thick backing coat in cement mortar 1:3 complete all as specified and directed. Note: Colour of granite shall be approved by GE

Demolition of reinforced cement concrete of any description and in any position not other wise spcifically provided for complete all as specified and directed.

M&L for brushing neat cement slurry with 3Kg of cement per square metre all as specified and directed.

Material and labour for ready mix cement concrete in Pavement/Hard standing (PQC) M-40 mixed with (admixture, senthetic & fibre) in field using minimum 375 Kg of cement per cubic metre laid in bays or as directed with and including steel formwork to sides of concrete spread, compacted and finished in a continuous operation etc all as specified and directed.

M&L for forming 12mm thick expansion joints filled with pre formed bituminous filler and top 30mm primed and sealed with sealing compound,grade 'A' complete all as specified and as directed.

M & L for GI powder coated snap grid frame work for false ceiling of grid size 600X600 mm of thickness 1mm with Hangers 2 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs with cement fiber board of 4mm thick of size 595mm x 595mm etc complete all as specified and directed.

M&L powder coated Aluminium frame and shutter for doors, sliding windows & ventilators (moveable louvers type) and for prtitions with one or more rebates including joining cleat for fixing etc. Rubber gasketing all round the panels/ shutters to fix glass, PVC gasketing in all channels, locking arrangement, (minimum thickness of powder coating 50micron) complete all as specified and directed.

S&F 5mm thick glass sheet one side frosted ordinary quality and glazing with in square, n exc 0.5 Sqm in each pane, fixed to Aluminium windows/ventilator with rubber beading in repairs complete all as specified and directed..

S&F in repair aluminum anodised GRILL (Deco grill DG 103 of 7.5 mm thick of M/s ELESAR FOCCHI Ltd. Or equivalent make in list of manufactures) fixed with suifable 'F' section No. 8584 15.30 x 23.40 x 1.40mm fabricated and rivetted to aluminum windows, complete all as specified and directed .

S & F in repairs 12 mm thick pre-laminated Medium Density board,both side decorative lamination interior grade,fixed in aluminium/ wooden frame work complete all as specified and directed.

M & L rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 finished even and smooth (with out using extra cement) including Sagol finish including irrection and dismantling of scaffolding to carrying out works up to 1 to 4 storeys buildings complete all as specified and directed.

M&L for one coat of Hydrolock by brush without dilution water proofing course over the finished surface complete all as specified and as directed .

M & L for preparing new plastered surfaces of walls and applying two coats of oil bound distemper with priming plastered and other surfaces with alkali resistant primer with 3mm thk wall care putty on plastered surfaces complete all as specified and directed.

M & L rendering 15 mm thick in CM (1:4) on external surface of wall incl WPC @ 3% by weight of cement including irrection and dismantling of scaffolding to carrying out works up to 1 to 4 storeys buildings complete complete all as specified and directed.

Supply only water profing compound @ 3 % by weight of cment complete all as specified and directed.

M&L for preparation of new platered wall surfaces of any description & applying two coats of acrylic (antifungal) exterior grade paint @ 1.67 lit/10 Sqm over and including priming coat @ 2.20kg/10 Sqm) on wall/roof up to 1 to 4 storeys buildings complete all as specified and directed.

M&L for preparation of old surfaces of of wall any description & applying one coats of acrylic (antifungal) exterior grade paint @ 1.67 lit/10 Sqm over and including priming coat @ 2.20kg/10 Sqm) on wall/roof up to 1 to 4 storeys buildings complete all as specified and directed.

M&L for preparation of old wall surfaces of any description & applying one coat of oil bound distemper paint on wall/roof complete all as specified and directed

S&F 110mm bore PVC(SWR) pipes single socketed in any length with rubber ring joint fixed to wall complete all as specified and as directed.

S&F 110 mm bore PVC (SWR) bends any radius complete all as specified and as directed.

S & F 100 mm Butt hinges, mild steel, with mild steel hinge pin, bright polished and fixed, type B-11 complete all as specified and as directed.

S&F 200mm long aluminium anodized barrel tower bolts of extruded sections as fixed in repairs complete all as specified and directed.

S&F 300mm long aluminium alloy, anodized sliding door bolts with hasp & staple (bolt type) and fixing clips of sheet cost of extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed.

S&F for 140mm long floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floor complete all as specified and as directed

S & F 150mm extruded aluminium alloy handles, cast type as fixed complete all as specified and directed.

S & F 100mm extruded aluminium alloy handles, cast type as fixed complete all as specified and directed.

M & L for preparation of new wooden surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

S & F in repairs prelaminated 12mm thick particle board exterior grade prelaminated both sides with decorative choice lamination fixed with screws to timber/ metal frame work in repairs complete all as specified and directed

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.4mm complete all as specified and as directed..

S&F in repairs 4 mm thick bakelite sheet with decorative choice laminated on both side completion as specified and as directed

S&F Solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers complete all as specified and as directed.

M&L for toughned glass 10mm thick, as in hinged doors, partitions automatic doors and similar work including cutting to shape, drilling holes as required complete all as specified and as directed..

Removing debris exc. 1.50 Km but n exc. 20 Km and depositing where directed, in soil outside MD land complete all as specified and as directed..

Dismantling posts or struts (wood, steel or RCC) any section including taking out embedded portion in concrete complete all as specified and directed.

S&F mild steel works as in fencing, posts & struts in fencing embedded in stone masonry/bricks works including cutting tops to shape as directed, drilled holes notching for wires flat iron fillets (for securing wire mesh etc) inlcuding all drilling, bolting or riveting etc and similar work conforming to Fe-410 or Fe-310-0 complete all as specified an directed.

Framed work such as grills, gratings, sun shed etc with ends of bars shouldered and/or riveted or welded, or forged into spikes, framed guard bars, barred iron doors, ladders, farmed balastures, walk ways, railings, frame work of water tanks and similar work conforming to Fe-410-0 or Fe-310-0 complete all as specified and directed.

S&F in repairs Galvanized, 2 strand, steel barbed wire 2.24 mm dia., barbed with 2 mm dia., barbs at 75 mm spacing and strained and fixing to any type of standard rails straining bolts, etc. all as directed. (Note: each line wire to be measured)

S&F wire barbed tape concertina coil wire of 50 turn and 2.6mm dia having core wire of high carbon spring steel of high tensile strength and a carbon steel strip of 20mm width, 0.5mm thick having razor sharp barbs punched tape and core wire hot dip galvanized, as fixed in repair complete all as specified and as directed..

Dismantling fencing wire mesh, any type complete all as specified and as directed.

S & F mild steel security chain link fencing 60mm x 60mm mesh made out of 3mm dia MS wire and 1.00mm thick PVC coating throughout fixed to RCC post including binding wire complete all as specified and directed.

Fixing only chain link fencing including lines wires, any mesh,size and type to any type of standards, rails,straining bolts etc inculding provision of binding wire complete all as specified and as directed .

S&F mild steel round bars 10mm dia and over, in horizontal support for chain link straining of fencing including cut to length, bent to shape required including cranking, bending spirally for hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to Fe-410-W (Gde E-250) complete all as specified and directed.

S&F mild steel screw bolts 10mm dia with hexagonal or square heads at one end and screwed at other ends dia of shank 5 to 10 mm and length of bolt exc. 5cm but n.exc 10cm complete all as specified and directed.

S&F 4mm thick polycarbonate roof sheet of required profile with shelf taping screw as view cutter over the frmaed MS work complete all as specified and as directed .

Demolition of cement concrete in ground floor and paving not exceeding 15cm thick below or above ground level un re-inforced complete all as specified and directed. .

M&Lfor Hard core, broken stone/boulder, broken to gauge n exc 63 mm.complete all as specified and as directed.

M&L for preparing new or previously untreated surface of any description, over 10cm in width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

M&L mild steel TMT bars 6 to 8mm dia and over cut to length bent shape as required including cranking bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to Fe-410-S complete all as specified and as directed

Cutting Reninforcement Cement concerete round, square or any size, grooves or rebates including hardner fixing and applying n exc 250mm girth, in cement concerete and trimming surface all as specified and directed.

Taking down cement plaster on brick walls or stone walls etc including raking out joint, hacking for key, scrubbing down with water etc including removing debries directed for a distance max upto 500m complete all as specified and as directed.

M&L for Rendering 15mm thick on brick work or concrete surface in cement mortar 1:4 finished even and fair all as specified and directed.

Dismantling stone slab and tiles of of any description or thickness laid bedded and pointed in any mortar in floors, aprons complete all as specified and as directed

Dismantling floor hearth or wall tiling including cement mortar bedding (not for backing),removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

M&L for providing edge moulding to 18-20mm thick granite including machine polishing to edge to give high glossy finish etc complete all as specified and as directed.

M & L for machine pressed precast concrete interlocking paver block With Grey cement and pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 Grade complete over 25 mm thick Sand cushion complete all as specified and as directed.

M&L double charged premium quality vitrified ceramic tile (light shade) 10mm thick (square/rectangular) polished area of each tile not exceeding 0.36 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match in floor including 15mm thick screed bed or bedding layer for laying floor finishes in CM 1:4 etc set and joined in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L double charged premium quality vitrified ceramic tile (light shade) 10mm thick (square/rectangular) polished area of each tile not exceeding 0.36 Sqm (600x600mm), but as on vertical surfaces such as skirting/dado including 10mm thick rendering in CM 1:3 etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for complete removal of existing treament on wall surfaces and applying a coat wall care putty 3mm thick on plastered surfaces preparatory to distempering and applying two coats of oil bound distemper over a coat of alkali resistant primer complete all as specified and as directed.

Taking down chowkats or frames but n exc 1.5 sqm each but with shutters (without taking off shutters from the frame) complete all as specified and as directed.

S &F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp?ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and as directed. (Note: M.S. hold fast/ lugs or SS dash fasteners shall be measured and paid seperately).

M&L for providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and as directed. (Note: stainless steel butt hinges and necessary S.S screws shall be measured and paid separately).

S&F in repair 300 mm long Brass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled of drawn brass bolts and fixed complete all as specified and as directed.

Supply and fix 150mm size brass handle cast type polished bright complete all as specified and as directed.

S & F 100 mm Butt hinges, cast brass, with mild steel hinge pin, bright polished and fixed, type B-11 complete all as specified and as directed.

S&F 200mm long brass barrel tower bolts of extruded sections as fixed in repairs complete all as specified and directed.

S&F in repair for 140mm long floor door stopper of brass body and tongue, anodised with hard drawn steel spring fixed in floor complete all as specified and as directed

S&F in repair 75mm dia of outler cast iron nahani trap , with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and directed.

M & L for Non skid coloured ceramic tiles 7 to 8 mm thick ( square/ rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of the tiles with and including 15mm thick screed bed in CM 1:4 complete all as specified.

M & L for Coloured glazed ceramic tiles in vertical surface area of tiles n exc 0.18 Sqm thick with and including 10 mm thick cm (1:4) backing coat and Triangular filliting at top of skirting, set and jointed in neat cement paste and pointed in coloured cement to match the shade of the tiles complete all as specified and as directed.

Taking up and down 15 mm bore GI tubing and connection including cleaning for re-fixing or removing to store complete all as specified and directed.

All as per item No.89 above but for but 20 mm bore complete all as specified and directed.

S & F GI tubes medium grade galvanised with all fitting and fixed complete to walls and ceiling or laid in floors 15 mm bore of pipe complete all as specified and directed.

All as per item No.91 above but for 20 mm bore of pipe complete all as specified and as directed.

S&F fancy type chromium plated cocealed stop valves 15 mm bore cast copper alloy (Make: Jaquar Cat No OPP-CHR-15083KPM or equivalent make in list of manufactures) fixed in repairs complete all as specified and directed.

S & F in repairs single piece WC with UF Soft close slim seat cover fixing accessories, accessories set and cistern fitting incl trap/connecting piece complete all as specified and directed. (Make-Jaquar of cat No FSS-WHT-29853S300UFSM or equivalent make in list of manufactures).

S&F counter top wash hand basin including chromium plated brass waste coupling and PVC waste pipe complete all as specified and directed. (Make :Jaquar CAT PART NO- ALS-WHT-85601 or equivalent make in list of manufactures)

S&F in repair for seat cover for single piece WCs for pedestal pan with plastic water closet seat , black or white, closed pattern with flat bottom and cover amnd mild steel chromium plated or aluminised hinging device complete all as specified and directed.

S & F for 10 litre capacity PVC valveless syphonic action type flushing cistern high or low level (exclusive of brackets) white with inlet ball valve, float and handle inlcuidng brackets complete all as specified and directed.

S & F in repairs for providing 15 mm dia PVC connection of length 450mm long complete all as specified and directed.

S&F in repairs CP toilet roll holder with flap (Make - Jaquar CAT PART NO_ 1153N or equivalent make in list of manufactures) complete all as specified and as directed

S&F in repairs health faucet ABS Body with 8 mm dia 1 mtr flexible tube and wall hook (Make - Jaquar CAT PART No-ALD-CHR-585 or equivalent make in list of manufactures) complete all as specified and as directed .

S&F in repairs CP towel ring square with round flange (Make - Jaquar CAT PART NO -CAN-1121N or equivalent make in list of manufactures) complete all as specified and directed.

S&F 32 mm dia WHB/urinal flexible waste pipe complete all as specified and directed.

S&F in repair cast copper alloy chromium plated soap container (soap dish) fixed with chromium plated brass screw and wooden / plastic cleats complete etc all as specified and directed .

S&F in CP toilet roll holder with flap (Make - Jaquar CAT PART NO_ 1153N or equivalent make in list of manufactures) complete all as specified and directed.

S&F in repair corner glass shelf with brackets (Make - Jaquar CAT PART NO- CAN-1173 or equivalent make in list of manufactures) complete all as specified and directed.

S&F in repair 600 mm glass self assembly fency type with CP frame (Make - Jaquar CAT PART NO AKP-35771P or equivalent make in list of manufactures) fixed with chromium plated brass brackets and screw complete all as specified and directed.

S&F in repairs CP Pillar cock taps 15 mm bore with lift type operating knob and base flange (Make - Jaquar CAT PART NO- FLR-5015 or equivalent make in list of manufactures ) complete all as specified and directed.

S&F in repairs CP bib cock 15 mm bore (Make Jaquar CAT PART NO- FLR-5047N or equivalent make in list of manufactures) complete all as specified and directed.

S&F in repairs CP angular stop cock with wall flange of 15 mm bore (Make - Jaquar CAT PART NO- FLR-5053N or equivalent make in list of manufactures) complete all as specified and directed.

S&F PVC bathroom cabinet with 4mm thick looking mirror of overall size 560x410mm of approved tint and pattern and drilling in and fixing with 02 Nos. chromium plated screws complete all as specified and as directed

Taking down PVC wastage and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, complete all as specified and as directed

M & L for preparing new plastered surfaces of walls and applying two coats of oil bound distemper over a coat of chalk whitening on plastered surfaces complete all as specified and directed.

M&L for PCC 1:4:8 type D2 using (40mm graded stone aggregate) as in flooring, 100mm thick etc complete all as specified and as directed

Excavation in trenches not exc 1.5 m wide and not exc 1.5 m in depth for foundation and getting out hard dense soil complete all as specified and as directed.

M&L for PCC 100mm thick type D-2 (1:4:8) using 40mm graded aggregate as in sub base complete all as specified and as directed

Repair to pot holes any depth n.exc 1 Sqm each including sweeping free from dust and mud, or water scoring sunken surfaces in roads, paths, etc. Cutting around edges to atleast 25mm in depth, making good by filling in screened and graded road metal with cold bitumen and well ramming including supply of road metal complete all as specified and directed .

sai construction (BID ID -3093340)

Rohit Enterprises (BID ID -3090379)

jalandhara construction (BID ID -3091163)