PROVN OF TOILET BLOCK FOR OTHER RANK NEAR P 11 ANNEX BLDG AT KWC TIMARPUR AND CERTAIN OTHER SANCTIONED WORKS UNDER GE NORTH DELHI CANTT 10

Amount

Taking down cement or cement plaster on brick walls/ceiling etc including raking out joints, hacking for key, scrubing down with water etc complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed.

Taking down chowkhats or frames with shuttes (without taking off shuttes from the frame) exc 1.5 sqm but n exc 4 sqm each complete all as specified and directed.

Taking down chowkhats or frames with shuttes (without taking off shuttes from the frame) n. exc 1.5 sqm each complete all as specified and directed.

S&F Aluminium window as per TD drg No. CEDZ/TD-316 with following specifications :- (i) Outer frame of size 40mmx114mm with 1.3mm thickness, corner 45 degree cut & aluminium welded. (ii) Center mullion of size 40mmx65mm. (iii) Welded shutter (02 Nos) of size 40mmx60mmx1.3mm thickness 45 degree cut mechanically joint with 6mm allen key bolt clamp with 5mm clear glass both side EPDM rubber gasket metal body hand lever type single point lock, aluminium kobra hinges 2 Nos per shutter. (iv) 12mm SS 202 grade round bar safety grill at 100mm cc distance modified to 150mm cc distance in front of handle, welded at both ends with 6mm SS 202 grade round bar. (v) Welded wiremesh shutter (2 Nos) of size 40mmx18mmx1.3mm thickness 45 degree cut with 0.45mm nominal dia of SS wire mesh, SS 75mm long hinges & PVC magnet. (vi) Entire window shall be powder coated with pure polyster coat of any shade as approved by GE. (vii) Window shall be installed with silicone complete all as specified and directed by Engr-in-charge.

S&F Aluminium window as per TD drg No. CEDZ/TD-316 with following specifications :- (i) Outer frame of size 40mmx114mm with 1.3mm thickness, corner 45 degree cut & aluminium welded. (ii) Center mullion of size 40mmx65mm. (iii) Welded shutter (02 Nos) of size 40mmx60mmx1.3mm thickness 45 degree cut mechanically joint with 6mm allen key bolt clamp with 5mm clear glass both side EPDM rubber gasket metal body hand lever type single point lock, aluminium kobra hinges 2 Nos per shutter. (iv) 12mm SS 202 grade round bar safety grill at 100mm cc distance modified to 150mm cc distance in front of handle, welded at both ends with 6mm SS 202 grade round bar. (v) Welded wiremesh shutter (2 Nos) of size 40mmx18mmx1.3mm thickness 45 degree cut with 0.45mm nominal dia of SS wire mesh, SS 75mm long hinges & PVC magnet. (vi) Entire window shall be powder coated with pure polyster coat of any shade as approved by GE. (vii) Window shall have provision for installation of window AC/Desert Cooler and provision of window glass shutter, wiremesh, grill and necessary fittings and locking arrangements for subject portion will be modified as per ground requirement during the execution as per directions of Engr-in-charge. (viii) Window shall be installed with silicone complete all as specified and directed by Engr-in-charge.

M&L preparation of newly plastered surface on walls and applying two coat of oil bound distemper over a coat of 2mm thick wall care putty complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying two coat of cement based paint over a coat of alkali resistant primer complete all as specified and directed.

M&L non skid ceramic colored tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floor etc set and jointed in neat cement slurry and pointed in colour cement laid over and including 15mm thick cement mortar screed bed in CM 1:6 complete all as specified and directed.

M&L for glazed coloured ceramic tiles in wall surfaces area of each tile exc 0.075 to 0.15 Sqm, 7-8mm thick set and jointed in neat cement slurry and pointed in coloured cement to match the surface including 10 mm thick in cement mortar 1:4 even and fair for receving tiles on vertical surface complete all as specified and directed by Engr-in-Charge.

S&F butt hinges, 100 mm size medium weight, cold rolled stain less steel complete all as specified and directed.

S&F aluminium handles 150 mm size cast type, anodised complete all as specified and directed.

S&F 200 mm long aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 150 mm long aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 300 mm aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast of extruded sections and fixing bolts and sliding bolts of extruded sec or cast aluminium and fixed complete all as specified and directed.

Taking down/dismantling old particle board or any board kitchen cabinet with wardrobe including fillets and making good disturbed surfaces all assessary complete all as specified.

S&F factory made 18mm thick 100% Solid WPC ( Wood polymer Composite ) Plain Board of required size comprising of virgin PVC resin of K Value 57-60 (Suspension Grade), Calcium Carbonate and natural Fibers (Wood Powders/ rice husk/ wheat husk) and Non toxic additives, made froms Extrusion process WPC foam sheet Single Extruded (Inner) with density not less than 650 kg/cbm Certified Company, having good screw holding capacity (Screw Withdrawal strength of 2000 N (Face) & 1100 N (Edge), Minimum Compressive Strength of 50 N/mm2, Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free. Water/ Moisture Proof, Fire Retardant and fixing with stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer -In-Charge, Material test certificate and authentication should be compulsory provided by the manufacturing company: For WC/Bathroom/Toilet/Kitchen & Cabinets.”

S&F factory made 18mm thick 100% Solid WPC ( Wood polymer Composite ) Laminated Board of required size comprising of virgin PVC resin of K Value 57-60 (Suspension Grade), Calcium Carbonate and natural fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet. Single Extruded ( Inner ) with having minimum density not less than 650 kg/cbm having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compressive strength of 50 N/mm2 , Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free. Water/ Moisture Proof and Fire Retardant. WPC to be Laminated with PVC foil of minimum 14 microns thick of approved design pasted on both faces of shutter and fixing stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer -In-Charge, Material test certificate and authentication should be compulsory provided by the manufacturing company: For WC/Bathroom/Toilet/Kitchen and Cabinets.

S&F magnetic catches with steel body 'H' type, fixed to shutter complete all as specified and directed.

S&F 100 mm dia oval shape brass handle fancy type polished bright finished complete all as specified and directed.

S&F continous (Piano) hinges, brass, 30mm width of flaps (when open) complete all as specified and directed.

S&F in repair 4 levers brass cup board locks grade-I size 65mm complete all as specified and directed.

M&L for granite work table rubbed polished in kitchen cooking platform including 20mm thick cement mortar screeding in CM 1:4 pointing in white cement using marble dust with admixture of pigment to match with shade of granite including taking down of old damaged granite/marble complete all as specified and directed.

S&F stainless steel basket (plain) of size 50cm x 37cm x 10cm made of 4mm thick S.S. wire approved quality with suitable arrangement for fixing Telescope basket (channel) 11/25 inch length two way extruded MS galvanised over rollers of approved make complete all as specified and directed.

S&F stainless steel thali basket (11-13 division) of size 50cm x 37cm x 20cm made of 4mm thick S.S. wire approved quality with suitable arrangement for fixing Telescope basket (channel) 18/25 inch length two way extruded MS galvanised over rollers of approved make complete all as specified and directed.

S&F stainless steel plate basket (11-13 division) of size 50cm x 37cm x 16cm made of 4mm thick S.S wire aproved quality with suitable arrangement for fixing Telescope basket (channel) 18//25 inch length two way extruded MS galvanised over rollers of approved make complete all as specified and directed.

S&F stainless steel partition basket of size 50cm x 37cm x 16cm made of 4mm thick S.S. wire approved quality with suitable arrangement for fixing Telescope basket (channel) 18/25 inch length two way extrude MS galvanised over rollers of approved make complete all as specified and directed.

S&F stainless steel cutlary basket of size 50cm x 37cm x 10cm made of 4mm thick S.S. wire and bottom of S S perforated sheet approved quality with suitable arrangement for fixing Telescope basket (Channel) 18/25 inch length two way extruded MS galvanised over rollers of approved make complete all as specified and directed.

S&F stainless steel basket (plain) of size 50cm x 37cm x 16cm made of 4mm thick S.S wire approved quality with suitable arrangement for fixing Telescope basket (channel) 18/25 inch length two way extruded MS galvanised over rollers of approved make complete all as specified and directed.

S&F stainless steel bottol full out of size 50cm x 40cm x 16 cm in two tier made of 4mm thick S.S wire approved quality with suitable arrangement for fixing Telescope basket (channel) 18/25 inch length two way extruded MS galvanised over rollers of approved make complete all as specified and directed.

S&F telescope basket (channel) 18/25 inch length extruded MS galvanised over rollers of approved make complete all as specified and directed.

S&F in repair 15mm dia chromium plated quarter turn wall mixer hot & cold L bend 3 in 1 pattern fixing and connection to pipes, complete all as specified and directed. Make:- Jaquar Cat Part No.FLR5281N/CERA Cat Part No.F2008401/Hindware Cat Part No.F570022

S&F in repairs kitchen sink mixer 15mm dia CP brass fancy type including joints to steel pipe or unions, complete all as specified & directed. Make Jaquar, CERA , Hindware

Dismantling posts or struts (wood, steel or RCC) any section, including taking out embedded portion and making good disturbed ground, complete all as specified and directed.

Dismantling of fencing wire mesh, any type, complete all as specified and directed.

Dismentling wrought iron or mild steel work of any description not other wise provided.

Excavation in post holes (or similar holes ) each n. exc 0.5 Cum in soft/loose soil, getting out,removing soil to a distance n. exc 50M , complete all as specified and directed.

M&F for plain cement concrete (1:4:8) type D-2 using 40mm graded crushed stone aggregate as in foundation, filling and mass concrete, complete all as specified and directed.

M&L for mild steel angle iron posts and struts, MS flat iron fillet securing chain link fencing confirming to FE-290 E-165 as in fencing including cutting tops for required shape, drilling holes,bolting, notching for wire including all necessary drilling of similar work, complete all as specified and directed.

Supply only GI Chain link fencing with PVC coating 100 x 100mm mesh, 8 SWG wire fixed to angle iron ith flat iron, confirming to IS, type standards rails, straining bolts etc including provision of binding wire, complete all as specified and directed.

Fixing only chain link fencing including line wire, any mesh, size and type to any type of standards, rails, straining bolts etc. including provision of binding wire, complete all as specified and directed.

M&L for mild steel round bars 10 to 12mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

S&F MS screw bolts (machine made) with hexagonal or square heads at one ends and screwed the other, or screwed both ends, each screwed end to be fitting with washer and one hexagonal or square nut n.exc. 5cm long and dia of shank 8 to 10 mm etc.

M&L applying two coats of synthetic enamel paint on new steel surfaces of any description over 10cm width or girth over a coat of red oxide primer including preparation of steel surfaces complete.

M&L for prepration of new steel surfaces of any description, n.exc 10cm in width or girth when unconnected with other painting or when painted in a different tint

M&L for matt finish exterior wall tiles 8 to 10mm thick & not exc 0.18 sqm , colour & shade of tiles as approved by Engr-in-charge,set and jointed in neat cement slurry and pointed in coloured cement to match the surface etc complete all as specified and directed by Engr-in-Charge.

S&F rolled mild steel as in doors or gate of angle of other section with gusset plates, rails, braces, etc coplete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and incl either hooks and hinges or steel hanging door fitting(exlusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete.

Demolition of cement concrete (un-reinforced) in ground floors and pavings n. exc. 15cm thickness (below or above ground level) all as specified and directed.

M&L for laying of APP modified roof treatment over existing non-accessible RCC roof slab / chajjah / canopy / parapet of the membrane manufacturer with following specification etc complete all as specified and directed :- (a) removing and Cleaning existing damaged APP membrane from roof surface and clean all cement mortar and vegitation, plants with roots properly. (b) Applying oil bound bitumen primer @ 0.30 liter/Sqm manufacture by the same agency as that of APP with a density 0.87-0.89 Kg per litere at 25 degree centigrade on prepared surface. (c) Laying not less than 3mm thick APP modified water proofing membrane weighing not less than 3.00 Kg/Sqm reinforced with non woven polyster fiber weight not less than 160gsm/Sqm using butane torch application with 10cm side laps and 15cm end lap over hot bitumen 85/25 grade @ 1.2 Kg/Sqm overbituminous primer before Laying of membrane. (d) APP membrane shall be laid using butane torch by Torch application with minimum 10cm side overlap and 15cm end lap. (e) Top of membrane shall be provide with solar reflective bituminous aluminum paint as prescribed by manufacture of membrane.

M&L for PCC 1:2:4 type B-0 padding on roof as in leveling to making slope, surface finished even and smooth without using extra cement.

S&F pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

S&F rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates complete all as specified and directed.

Supply only sand under floors or in foundation including weathering and consolidation complete all as specified and directed.

M&L 80 mm thick machine pressed precasting conc interlocking tiles/paver blocks any shape & size and top surface with Grey cement and pigement confirming to IS 15658-2006 of M-40 grade laid over 40mm thick sand cushioning complete all as specified and directed. Note:- Sand cushioning shall be measured and paid separataly.

M&L for plain cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in string courses copings or as floors complete all as specified and directed.

Surface excavation n. exc. 30 cm deep and averaging 15cm deep and getting out in hard/dense soil complete all as specified and directed.

Removing of surplus excavated/demolised materilas to a distance exc 1.5 Km but n.exc 5. Km and deposited where directed at a level n. exc 1.5 m above the starting point.

M&L hard core of broken stone/boulder of gauge ex 63mm and not exe 100mm complete all as specified and directed.

M&L for 100mm thick type-D-2 1:3:6 (using 40mm graded crushed stone aggregate) as in sub base to receive paver blocks all as specified and directed.

M&L for providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete.

M&L plain cement concrete type B1, (1:2:4), using 20 mm graded crushed stone aggregate as in benching, coping, surface channels and other similar nature of work etc. the like including form work and finishing all exposed surface of concrete including demolition of cement concrete any description and in any position not otherwise specifically provided for complete all as specified and directed.

Excavating in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth etc not exceeding 10 Sqm on plan for shafts, cesspits, manholes, pier holes, foundation etc and getting out in any type of soil complete all as specified & directed.

Returning filling in and including spreading levelling, watering and well ramming in layers n exc 25 cm thick complete.

Removing excavated material not exceeding 50m and depositing where directed at a lavel not exceeding 1.5m above the starting point, soil complete all as specified and as directed.

M&L for Hardcore of gauge n-exc 63mm of broken bricks ,deposited ,spread and levelled in layers n-exc 15 cm thick watered and rammed to a true surface complete all as specified.

M&L for M-25 concrete (using 20mm graded stone aggregates) in foundations including rafts, footings, foundation beams; plinth beams; bases for columns, etc. basement slabs, under-reamed piles and mass concrete complete all as specified.

M&L RCC as in Columns, pillars, piers, posts and struts type M-25(using 20mm graded) stone aggregate complete all as specified.

M&L RCC in beams, Cantilivers,bressummers, lintels over 1.5 mtr span uing type M-25(Design mix) (using 20mm graded) stone aggregate complete all as specified.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, flat surface complete all as specified.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions of shape Square, Rectangular or polygonal complete all as specified.

Form work to sides of concrete roof beams, lintels cantilevers etc including supports.

Form work to soffits of suspended slab such a roof slab etc not exc 200 mm thick complete all as specified.

Form work to edges of roof slab, RCC bands etc n.exc 200mm complete all as specified.

M&L RCC slab supported on walls , beams & colmns etc as in roof & the like using M-25(Design mix) using 20mm stone aggregate complete as specified.

M&L for mild steel TMT bars 10mm dia & over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality all as specified and directed.

M&L for mild steel bars 5mm dia and over upto and including 10 mm dia in stirrups, cut to length, bent to shape required, including cranking, bending spirally for hooping and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality confirming to TMT bars, complete all as specified and directed.

M&L for brick work with sub class'B' bricks straight or curved on plan exc 6 mtr mean radius built in CM 1:6

M&L for plain cement concrete M-10, nominal mix, type C-1, using 20mm graded mechanically crushed stone aggregate, 75mm thick as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), all as specified & directed. Note:- The unit rate include for use of form work (straight or curved).

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification complete all as specified.

S&F Factory made solid PVC Moulded shutter 28-30mm thick styles with 2,4 or 6 raised panels design with 2mm thick moulded prelam PVC sheet on the front face and 2mm thick prelam sheet on the back face with particle board core complete all as specified.

M&L for 5mm thick cement plaster on brick or concrete surfaces, as in ceiling / facia / chajja etc. in cement mortar 1:3 finished even and smooth without using extra cement, all as specified .

M&L Preparing new ceiling surfaces applying three coats of white wash complete all as specified.

M&L for 15mm thick ready mix plaster (make ultratech readiplast /birla aerocon RMP/ACC suraksha RMP) on brick work on concrete surface of wall (internal surfaces) finished even and smooth all as specified and directed by GE.

M&L 5mm thick ready mix plaster (make ultratech readiplast/ birla aerocon RMP/ ACC suraksha RMP) on ceilling surfaces finished even and smooth all as specified and directed by GE.

M&L 15mm thick ready mix plaster (make ultratech readiplast/ birla aerocon RMP/ACC suraksha RMP) on brick work on concrete surface of wall (external surfaces) finished even and smooth all as specified and directed by GE.

M&L for Preparing new plastered surfaces of walls two coats of exterior emulsion paint (Weather Coat) over a coat of priming paint etc complete all as specified

Cutting chases pinning in making good to facing where required for concealed water tubing and making good cutting not exc 10cm girth in brick walls complete.

M&L for 15mm bore steel tubes “medium grade” galvanised with all fitting and fixed complete in walls ceiling or laid in floors complete all as specified.

S&F Bib taps, long body, fancy type, chromium plated with crutch or butterfly handle screwed down for iron pipe or for brass ferrule and fixed for bore of pipe 15 mm, fixed all as specified.

S&F Stop valve/Angle valve 15mm bore dia or pipe, cast copper alloy but fancy type chromium plated screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified.

S&F Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed (concealed type) complete.

S&F Brass chromium plated shower rose 125mm size with or without swivel joints, any size, including fixing to steel pipe or union complete.

S&F for Gun metal gate valve with iron wheel head ,screwed both ends for iron pipe and fixed 20 mm bore complete all as specified.

S&F Tubular Towel rail 20mm dia, D type, 60cm long between flanges of brass chromium plated fixed with and including chromium plated brass screws and wooden / plastic cleats all as specified.

S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed

S&F PVC (SWR) floor trap, plain with grating including jointing with solvent cement, 75mm diameter of outlet, all as specified.

S&F VC (Star white) WHB counter top type of size 550x 400mm including CP waste fitting, complete all as specified and directed.

S&F Pillar taps, fancy type cast copper alloy, with capstan heads, chromium plated, for 15mm bore dia screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified.

S&F PVC (Plastic polymer Cistern) valve less, Symphonic action type, flushing cistern of capacity 10 liters, low level, white with inlet, ball valve, manually operated with one PVC ball valve horizontal plunger type including provision of 32mm PVC flush pipe of required length and making connections complete including taking down by dismantling the existing unserviceable cistern of any description.

S&F Vitreous china squalting pan of Orrisa pattern long pan size 580mm white with 'P' or 'S' trap front or back inlet and fost rest any pattern including connection to trap and to flushing pipe etc complete including lime concrete bedding and making good to floor.

S&F vitreous china urinal half stall type white including waste pipe and coupling (Excluding flushing cistern , flush pipe and waste pipe) complete.

S&F concussive push button taps 15mm bore of cast copper alloy, screwed for iron pipe and fixed

S&F PVC connections 15 mm size with PTMT nuts of length 600 mm long complete.

S&F Rotational moulded polyethene Water Storage Tanks 1000 ltrs capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I etc complete.

S&F ball brass valve high pressure with polythene float and fly nut complete screwed for Iron pipe 20mm bore

S&F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified.

S&F Cast iron 75mm bore Bends (any radius),PVC (SWR) bends any radius complete all as specified and as directed.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls , complete all as specified.

S&F stack clamps for 100mm bore pipe out of 50mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed.

S&F 110mm bore PVC(SWR) pipe vent cowl complete all as specified.

M&L 100 mm bore salt glazed stoneware drain pipe laid in trenches and jointed all as specified and directed

M & L cement concrete aggregate bed to drain pipe 100 mm dia including packing under and hunching against the sides of pipe after they are laid and tested in cement concrete 1:4:8 type D 2 using 40mm graded stone aggregate complete all as specified and directed.

Providing precast cement concrete in window or door cills, lintels, bressumers, steps,quoin blocks (for use with masonry), string courses, copings kneelers, apex stones, pier caps, columns, posts, boundary pillars, weatherings, throat- ing etc. and setting in CM 1:4complete with joints to match etc using type B1 , 1:2:4 (using 20mm graded) stone aggregate complete all as specifed and directed

M&L for 75 mm thick Cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate in sub base for laying floor finishes complete all as specified & directed.

S&F chequered cement concrete tiles of size 200mmx200mmx25mm thick with grey cement and no pigment laid as in floor set and jointed in neat cement slurry and pointed with coloured cement with 15mm thick cement screed in CM 1:4 complete all as specified and directed.

M&L for 15 mm thick screed bed over the concrete / brick roof surfaces in cement mortar 1:4 surface finished even and smooth without using extra cement all as specified and directed.

M&L for cement concrete type B-1, 1:2:4 using 20mm graded aggregate in kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed.

M&L for PCC type B 0 1:2:4 12.5 mm graded aggregate as in mass concrete complete all as specified and directed.

S&F steel water tubes, medium grade, ISI marked, galvanised, 15mm bore with all fittings, fixed to walls and ceiling or laid in floors including taking up or down steel tubing and connections complete.

Cleaning all the dust and loose material by brush /blower /Grinder including removing of vegetation/plantation from the surface. M&L for preparation of roof top surfaces, providing and applying single component elastic cold applied polyurethane modified acrylic roofing system, co elastic technology (CET) based on modified polyurethane and fully fibre reinforced, having Sun Reflectivity index (SR) of 109 on top of concrete roof surfaces. All cracks up to 3 mm at corner joints, channel and parapets should be treated with crack seal. Applying three coats including one coat of primer of ShaliUrethane BTD/ Sikalastic 560/ smart care damp proof-ultra having coverage @ min 0.75kg/m2 and dilution up to 10% and laying reinforced fiber net and applying two coats (without dilution) of shaliUrethane BTD/Sikalastic 560/smart care damp proof ultra @ total consumption 2 kg/m2 in two coats for maintaining minimum dry film thickness 1.5mm and elongation at break of free film of approx 350%. The materials shall be applied with brush or roller, complete in all respect as per the direction of Engineer-in-charge/Consultant (Note :6 Hrs interval between two coat will be maintained). All auxiliary and accessories involved during application should be supplied by single manufacturer as a part of system. Make: STP/Sika/Asian paint or equivalent as approved by GE. Note:- Application of water proofing treatment will be done by authorised applicator only.

S&F in replacement of electric water heater, storage type 25 ltrs capacity, BEE 5 star rated, vertical type with suitable size of fastner and incl provision and connecting up of SS braided pipe with adapter for inlet and outlet water connection, copper element corrosion resistance antiscaling magnesium anode having adustable knobe for temperature control and inner tank material of superior glass lined tank and outer body material ABS with high pressure with standing capacity upto 8 bar pressure having heating element 2 KW and minium two year warranty on product, minimum three years on heating element complete all as specified and as directed Note:- Old unserviceable geysers to be deposited in MES store.

M&L for sub main wiring with 4 sqmm (Nominal area) with two runs of single core cable PVC insulated FRLS multistrand unsheathed copper conductor cable including 1100 V grade, drawn through pvc conduit including 4 sqmm (nominal area) single core PVC insulated multistrand unsheathed copper conductor as earth wire and duly connected to all common earth point all as specified and directed.

S&F sheet metal enclosure with Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB with 20 Amps.

S&F MCB SP 240 Volts AC 6 - 40 Amps of breaking capacity 10 KA C curve.

Supply and fix refrigerator double door type, electric driven (single phase), capacity 235 Litres. BEE 5 star rated complete all as specified and directed.

Deep freezer hard top 400 Litre capacity having double door. electric driven (single phase) complete all as specified and directed.

Supply and fix water cooler electric driven (single phase), having approx storage capacity of 40 litre and nominal cooling capacity of 40 Litres per hour including connections pipes etc.complete all as specified and directed.

Supply and fix Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity 2 KVA complete all as specified and directed.

Supply and fix desert cooler electric driven (single phase), having nominal air flow capacity of 4000 Cum per hour (or nearest size) steel body complete all as specified and directed.

M&L for MS work of angle iron channels and iron flats for desert cooler stands as required size by welding to angle iron frame and framed work as in cooler base stand arrangement complete all as specified and directed.

M&L for point wiring with 1.5 Sqmm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed FRLS copper conductor cable with and including continuous earth wire of size 1.5 Sqmm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 20mm dia or higher, medium grade complete with and including all PVC conduit accessories concealed into wall by cutting of chases in wall and replacement of modular metal flush box, modular white cover plate with frame, blanking plate etc and making good to the disturbed surfaces to match the existing complete all as specified and directed for

All as per the description of srl item No.133 here in before but One light point controlled by one switch of 6Amp

All as per the description of srl item No.133 here-in-before but one fan point controlled by one, one way switch 06 Amps

All as per the description of srl item No.133 here-in-before but one 3 pin, 06 Amps socket outlet point on independent board controlled by one, one way 06 Amps switch

All as per the description of srl item No.133 here-in-before but one 3 pin, 06 Amps socket outlet point on same board controlled by one, one way 06 Amps switch

All as per the description of srl item No.133 above but point wiring with 2.5 Sqmm single core FRLS cables and earth continuity wire of 2.5 Sq mm single core FRLS cable for one 3 pin 15 Amps socket out let point controlled by one, one way switch on independent board complete all as specified and directed

S&F Switch piano flush type 5/6 Amps single pole one way 230 volts complete all as specified and directed.

S&F Switch piano flush type 15/16 A single pole one way 230 volts complete all as specified and directed.

S&F Socket Outlet 2 in 1, 3 pin 5 Amps flush type 230 volt complete all as specified and directed.

S&F Socket Outlet 2 in 1, 3/6 pin 5 and 15 Amp flush type 230 volts complete all as specified and directed.

S&F ceiling rose, 6 Amps, 250 volts, AC with three terminals and PVC / Polycarbonate insulated body of 50 x 25mm size complete all as specified and directed.

S&F surface mounting LED integrated aluminium housing batten luminaire with PC diffuser 20W, 4 feet fixture should have minium efficiency at level>=120lumens/watt, life of fixture not less that 50K Hrs, Ripple<5% UGR<19, Mimimum surge protection level of 4 KV, CCT 4000-6500K with same lumens/w CRI>80, PF>0.95, THD<10%@240V AC, an operating voltage range of 140-270V and all accessories pre-wired including connecting up with copper conductor wire of suitable size with connector block complete.

S&F (in replacement) surface mounting LED integrated aluminium housing batten luminaire with PC diffuser 10 watt 2 feet fixture should have minimum efficiency at level >=120lumens/watt, life of fixture not less that 50K Hrs, Ripple<5%, UGR<19, Minimum surge protection level of 4 KV, CCT 4000-6500K with same lumens/w CRI>80,PF>0.95, THD<10%@240V AC, an operating voltage range of 140-270V and all accessories pre-wired including connecting up with copper conductor wire of suitable size with connector block complete.

S&F LED sensor based bulkhead luminaire of polycarbonate housing and enclosed with acrylic diffuser IP-65 protection incl connection complete all as specified and directed.

S&F LED security light fitting of 35 watts with pressure die-cast aluminium housing complete with all accessories, fixing of fitting on wall with necessary fixing arrangement, IP66 protection as required at site & connection complete suitable for pole dia 40mm complete all as specified and directed.

S&F Ventilating fan, wall mounted type of 250 mm sweep, 240 volts, AC, 50 Hz capacity, cutting of hole in wall, making of wooden frame/all required arrangement for mounting of fan including making good of disturbed surface etc complete all as specified and directed. Note:- Noise level should not be more than 50db.

S&F MCB DB, single pole and neutral with 200 Amps rated bus bar, 230 volts, glazed, double door type, IP-43, including connecting all connections of wire to MCBs with proper lugs & making good to the disturbed surface complete for the following no of way :-

S&F MCB, DP/SPN, 240 Volts, AC of breaking capacity 10 KA, 'C' curve and connections by using suitable copper lugs complete of following rating :-

M&L for sand cushioning to under ground cable with a layer of sand 8 cm before laying the cable and 15cm after laying the cable (10 cm punned thickness above the top of the upper most cable, total 18 cm), complete all as specified and directed. .

M&L for sub class ‘B bricks, old size, brick covering laid dry, flat, transversally along the length of cable on sand cushioning, with width equal to the length of the brick, complete all as specified and as directed

Supply and laying or fixing or passing through pipe in repair of 1100V grade, heavy duty cable with XLPE insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed of size 10 sqmm 2 core nominal cross section complete

Supply, laying, jointing & testing of GI Pipe, medium grade, including all fittings in old/new position, laid in trenches/ wall including taking down the old/unsv pipe line complete all as specified & directed of following sizes :-

25mm dia

20mm dia

S&F in repair gun metal, globe or gate valve, screwed down high pressure with iron wheel head, screwed both ends complete for the following sizes of pipes :-

25mm dia

20mm dia

Ajay Sahu & Sons (BID ID -3504169)