SPECIAL REPAIR TO BLDG NOS TA284 TA264 P84 OF ARMY AVN SQN R AND O AND SPL REPAIR TO 35 KVA DG SET AT MES IB 320 KVA DG SET AT 1 LADAKH POWER HOUSE 200 KVA DG SET AT CLH HOUSE AND 320 KVA DG SET AT 134 POWER HOUSE UNDER GE 865 EWS

Amount

Demolition cement concrete in ground floors and pavings not exc. 15 cm thick, above or below ground level, complete all as specified and directed.

Demolition cement concrete of any descriptions and any position not otherwise specically provided for, complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified

Demolition of precast concrete block or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stone-work and precast concrete articles complete all as specified and directed by Engineer-in-Charge.

Taking down cement plaster of any description on brick or stone walls, concrete surfaces including racking out joints, hacking for key, scrubbing down with water remove dust, debries/rubbish etc, complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area not exceeding 1.50 square metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt. ) , complete all as specified and directed by Engineer-in Charge.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area exceeding 1.50 square metre and not exceeding 4.0 square metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt. ), complete all as specified and directed by Engineer-in Charge.

Taking down shutters of any description area exceeding 1 square metre and not exceeding 2.0 square metre each complete all as specified and directed by Engineer-in Charge.

Taking down shutters of any description area not exceeding 1 square metre each complete all as specified and directed by Engineer-in Charge.

M&L for 6mm thick venered decorated (knoty pine) ply wood (No of plys 05), grade I, with BWR resin with decorative face veneers on the face fixed with nails to timber frame work in stands, boards, partitions, shutters, as in wall and the like incluidng taking down old wall/ceiling board/ply wood complete all as specified and directed. Make : DURA PLY/GREEN PLY/DURO/BHUTAN BOARD/ CENTURY/DURIAN

M&L for 6mm thick venered decorated (knoty pine) ply wood (No of plys 05), grade I, with BWR resin with decorative face veneers on the face fixed with nails to timber frame work in stands, boards, partitions, shutters, as in ceiling and the like incluidng taking down old wall/ceiling board/ply wood complete all as specified and directed. Make : DURA PLY/GREEN PLY/DURO/BHUTAN BOARD/ CENTURY/DURIAN

9mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with nails to timber frame work as in walls complete incluidng taking down old wall/ceiling board/ply wood all as specified and as directed by Engr-in-Charge. MAKE: NOVA PAN/GREEN PLY BHUTAN BOARD/MYSORE WOOD BOARD/CENTURY PLYWOOD

9mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with nails to timber frame work as in ceiling complete incluidng taking down old wall/ceiling board/ply wood all as specified and as directed by Engr-in-Charge. MAKE: NOVA PAN/GREEN PLY BHUTAN BOARD/MYSORE WOOD BOARD/CENTURY PLYWOOD

M&L for second class soft wood clean swan as in battens for grids of ceiling and lining, plain fillets exc 13 sqcm and n.exc 25 sqcm, square/ rectangular in section , secured with nails or brads to timber frame work including dismantlng fillets,rails,posts,rafters,purlins, grids for ceiling & wall panelling etc under 40 Sq.cm in section complete all as directed.

M&L for second class soft wood clean swan as in beading for edges of ceiling, lining, wooden flooring work, plain fillets exc 6 sqcm and n.exc 13 sqcm, square/ rectangular in section , secured with nails or brads to timber frame work including dismantlng fillets,rails,posts,rafters,purlins ,grids for ceiling & wall panelling etc under 40 Sq.cm in section all as specified

M/L Cement concrete 1:2:4 type B1 using 20mm graded stone crushed aggregate in plinth protection, 75mm thick, finished even and smooth using extra cement, including making joints 12mm wide to the full depth of PCC at every 3 metres and at every change of direction and filling the same with & including bitumen and sand 1:3 by weight complete.

Forming Contraction (Dummy) Joints 65 mm deep x 10 mm wide, filled with sealing compound grade A, complete all as specified and directed.

M&L for plain cement concrete 1:4:8, type D-1 (using 20 mm graded crushed stone aggregate) 75 mm thick sub base, sub floor and pavings complete all as specified and directed.

Plain cement concrete 1:4:8 type D-2 using 40mm graded crushed stone aggregates as in sub base, foundation, filling and mass concrete, complete all as specified and as directed by Engineer-in-Charge

M&L for pre cast cement concrete block masonary of 1:3:6, type C-1 (using 20 mm graded crushed stone aggregate) with soild blocks, exc.10cm in width, set and jointed in cement mortor 1:6 complete all as spd and directed.

M&L for 10mm thick rendering in CM (1:6) on other than fair faces of brick work or stone masonary work, mixed with liquid water proofing admixture @ as per manufacturer's instructions by weight of cement finishing the surfaces with even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick rendering in cement mortar 1:4 on fair faces of brick walls or on concrete surfaces, finished even and smooth without using extra cement in complete all as specified and as directed

Material & Labour for 5mm thick rendering in cement mortar 1:3 on concrete surfaces, as in ceiling etc finished surface even and smooth, without using extra cement complete all as specified and as directed.

Supply only liquid Water Proofing Admixture complete all as specified and directed. Make : Pidilite/Dr Fixit

M&L 2nd class hardwood plain, solid, straight chowkats and frames, wrought, framed rebated on the soild, rounded or chamfered, put together with glue pinned at joints, supplied and fixed plain fillets, square, rectangular or triangular in section clean swan, secured with nails or brads complete all as specified.

Mild Steel Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

M&L PCC 1:3:6 type C1 (using 20 mm graded stone aggregate) as in hold fast, bed blcok and like complete all as specified and directed by Engr-in-Charge.

Factory made 35mm thick IInd Class Hard wood Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats, complete all as specified and directed by Engineer-in-Charge. MAKE: M/S WOOD PRODUCT INDORE/M/S GOYAL INDUTRIES CORPORATION 8743 DESH BANDHU GUPTA ROAD NEW DELHI/ M/S JAIN WOOD INDUSTRIES MURTHAL SONIPAT/M/S PIONEER TIMBER PRODUCT CHANDIGARH/M/S SHIV JOINERY& FURNITURE INDUSTRIES JAMMU/M/S M.S JOINERY WORKS, PARIMPORA, SRINAGAR

S&F powder coated (minimum thickness of powder coating 50 micron) anodised aluminium frames for door, windows, ventilators with one or more rebates including joining cleat for fixed etc complete all as specified. Make: JINDAL/INDAL/HINDALCO

S&F powder coated (minimum thickness of powder coating 50 micron) anodised aluminium door shutter, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading screws etc complete all as specified and directed. Make: JINDAL/INDAL/HINDALCO

Anodised aluminium powder coated (minimum 50 micron thickness) windows and ventilator shutter, side hung type with out sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, anodized aluminium fittings such as 150 mm long peg stay (01 No), 100mm long (2 Nos) hinges, 200mm long (1 Nos) suitable handles, 250 mm long aluminium Tower bolt (01 No), aluminium snap beading, screws, etc. complete all as specified and as directed. Make: JINDAL/INDAL/HINDALCO

Anodised aluminium powder coated (minimum 50 micron thickness) anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, anodized aluminium snap beading screws, anodised aluminium fittings complete all as specified and as directed. Make: JINDAL/INDAL/HINDALCO

Plain Sheet glass 5.5 mm thick, ordinary quality and glazing with oil pane putty in squares not exceeding 0.5 Sq. mm in each pane complete, complete all as specified and as directed. Make : Atul/Modi Guard/Sant Gobin

S&F for aluminum, anodized, barrel tower bolts, ISI Marked, of extruded section 150 mm long, complete all as specified and directed.

S&F for aluminum, anodized, barrel tower bolts, ISI Marked, of extruded section 100 mm long, complete all as specified and directed.

S&F 300mm long aluminium alloy, anodized, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolts of extruded section or cast aluminium alloy fixed complete all as specified and as directed

S&F 150 mm size extruded aluminum alloy handles, fabricated type anodised complete all as specified and directed by Engr-in-Charge.

S&F 100 mm size extruded aluminum alloy handles, fabricated type anodised complete all as specified and directed by Engr-in-Charge.

Aluminium (extruded section body) door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 in width and of weight between 61 to 80 kg, fixed in repairs, complete all as specified and dirceted. MAKE: GODREJ/DROMA INDIA/DYANA/EVEREST

Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed, fixed in repairs, complete all as specified and dirceted. MAKE: GODREJ/DROMA INDIA/DYANA/EVEREST

S&F floor door stopper (Length of cover plate) 150mm long aluminium alloy body and tongue anodised with hard drawn steel spring fixed in floor complete all as specifed and directed

S&F for mild steel butt hinges, medium weight cold rolled 100mm size complete all as specified and as directed.

S&F for mild steel butt hinges, medium weight cold rolled 75mm size complete all as specified and as directed.

S&F 100mm long aluminium anodized, butt hinges of extruded section complete all as specified and directed.

S&F in repair 250mm long aluminium alloy, anodized, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolts of extruded section or cast aluminium alloy fixed complete all as specified and as directed

M&L for preperation of new concrete /plastered wall surface of any description, applying three coat of white wash complete all as specified and as directed

M&L for preperation of old plastered wall surface of any description, applying two coats of white wash complete all as specified and as directed

M&L for preperation of new plastered ceiling surface of any description, applying three coats of white wash complete all as specified and as directed

M&L for preperation of old concrete /plastered ceiling surface of any description, applying two coats of white wash complete all as specified and as directed

Preparation of new or previously untreated wooden or wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint over and including one coat of pink primer complete all as specified and directed by Engineer-in-Charge. MAKE: NEROLAC PAINTS/ JENSON & NICHOLSON/BERGER PAINTS/ICI DULUXE/ASIAN PAINTS

Preparation of old decorated surfaces of wood and wood based material of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engr-in-charge. MAKE: NEROLAC PAINTS / JEHNSON & NICHOLSON / BERGER PAINTS / ICI DULUXE / ASIAN PAINTS

M&L for preperation of new concrete /plastered wall surface of any description and applying two coats of distemper oil emulsion over a coat of primer complete all as specified and as directed. MAKE: NEROLAC PAINTS / BERGER PAINTS / ICI DULUXE / ASIAN PAINTS

M&L for preperation of old decorated concrete /plastered wall surface of any description and applying two coats of distemper oil emulsion complete all as specified and as directed. MAKE: NEROLAC PAINTS / BERGER PAINTS / ICI DULUXE / ASIAN PAINTS

M&L French polishing on old treated surface of wood or wood based surface of any width or girth or any description, including cleaning and preparing the surface including a coat of wood filler on old surface with two coats complete all as specified and as directed.

M&L 100 mm thick plain cement concrete 1:4:8 type D-2 using 40mm graded crushed stone aggregates as in sub base, foundation, filling and mass concrete, complete all as specified and as directed by Engineer-in-Charge.

M&L PCC 1:2:4, 100 mm thick type B-2 using 40mm graded crushed stone aggregate as in floor finished even and fair with out using extra cement complete all as directed by Engr-in-charge.

M&L for plain cement concrete 1:2:4, type B-0 (using 12.5 mm graded crushed stone aggregate) 25 mm thick sub base, sub floor and pavings complete all as specified and directed.

M&L non-skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed or bedding layer in Cement Mortar 1:4 for laying floor finishes complete all as specified and directed. MAKE: KAJARIA/H&R JOHNSON/CERA/ NITCO/SOMANY

S&F 2mm Fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with L type J type hooks or cranked bolts and washer in roof, wall etc including taking down of old plain or corrugated sheet of any type and size, complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame/wooden frame including punching or drilling out old glazing pins/spring clips complete all as specified and as directed.

Plain Sheet glass 3.00 mm thick, ordinary quality and glazing with oil pane putty in squares not exceeding 0.5 Sq. mm in each pane, complete, complete all as specified and as directed. Make : Atul/Modi Guard/ Sant Gobin

35mm thick, factory made 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete, all as specified and directed by Engr in Charge. M/S WOOD PRODUCT INDORE / M/S GOYAL INDUTRIES CORPORATION 8743 DESH BANDHU GUPTA ROAD NEW DELHI / M/S JAIN WOOD INDUSTRIES MURTHAL SONIPAT / M/S PIONEER TIMBER PRODUCT CHANDIGARH / M/S SHIV JOINERY& FURNITURE INDUSTRIES JAMMU / M/s M.S JOINERY WORKS, PARIMPORA, SRINAGAR

M&L for welding in repairs exc 2.5 cm but not exc 5cm in length, not exc 6mm thickness of metal to be welded complete all as specified and directed by Engr-in-Charge.

M&L for preperation of existing treatment on steel / CGI sheets of any description and applying two coats of synthetic enamel paint (galvanisatin should be removed if required) ,complete all as specified and as directed. MAKE: BERGER PAINTS / ASIAN PAINTS / NEROLAC PAINTS / GOODLASS

M&L for plain cement concrete 1:4:8, type D-2 (using 40 mm graded crushed stone aggregate) 100 mm thick sub base, sub floor and pavings complete all as specified and directed.

M&L PCC 1:2:4, 100 mm thick type B1 using 40mm graded crushed stone aggregate as in floor finished even and fair with out using extra cement complete all as directed by Engr-in-charge.

Vitrified ceramic tiles 10 mm thick (ligh shade) (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bed or bedding layer in Cement Mortar 1:4 for laying floor tiles complete all as specified and directed. MAKE: KAJARIA/H&R JOHNSON/CERA/ NITCO/SOMANY

M&L for 20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite laid over and including 20 mm thick cement screed bed in CM 1:4 complete all as specified and as directed.

M&L non-skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed or bedding layer in Cement Mortar 1:4 for laying floor finishes complete all as specified and directed. MAKE: KAJARIA/H&R JOHNSON/CERA/ NITCO/SOMANY

Rotational moulded polyethylene water storage tank, inner and out white, two layers, ISI marked (cylinderical vertical with closed top) hoisted with threaded cap and fixed in position all as specified in SSR Part-I of Capacity 500 litres each including all accessories (i.e GI nipples, etc), including provn of 20/15mm dia spout for connecting inlet, outlet, overflow and washout pipes, including taking down of old broken water tank complete all as specified and as directed by Engr-in-Charge. MAKE : SINTEX/POLYWELL/ROTEX/POLYCON

Chromium plated, fancy type stop valve/cock, cast copper alloy, screwed down, high pressure with handle, chromium plated, screwed end for iron pipe or for union and fixed, suitable for 25mm bore pipe, complete all as specified. MAKE: PARKO/MARC/ESS ESS/CERA

S&F 25mm bore ball brass valve high pressure with polythene float and fly nuts complete screwed for iron pipe or brass ferrule. Make : Paryag/Polytuff/Supreme

15mm bore bib tap, (minmum weight 350 gms), chromium plated, fancy type, cast copper alloy with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule, fixed in repairs, complete all as specified and directed by Engineer-in-Charge. MAKE: PARKO/MARC/ESS ESS/CERA

S&F 15mm bore 3-layer PP-R Polypropylene random copolymer concealed pipes SDR 7.4 (PN 16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass treaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc including taking up or down 15 mm bore steel tubing & connection complete all as specified. Make : JINDAL/KISAN/SFMC/Supreme/Kanha Plastic Pvt Ltd

S&F 25 mm bore 3-layer PP-R Polypropylene random copolymer concealed pipes SDR 7.4 (PN 16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass treaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc including taking up or down 25/32 mm bore steel tubing & connection complete all as specified. Make : JINDAL/KISAN/SFMC/Supreme/Kanha Plastic Pvt Ltd

S&F in repairs sinks made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm, complete all as specified. Make : NIRALI/NEELKANTH/JAYNA/SILVERSHINE/JINDAL

M&L Machine cut Kota stone slab flooring 20-25 mm thick over 20mm thick cement screed bed or bedding layer in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete all as specified and directed.

Cutting out cracks to V section in existing roofs or terracing, celaning out, wetting, grouting with cement and sand slurry 1:3 complete all as specified and directed.

M&L for picking, swiping clean and washing down with wire brushing and cleaning top surface of roof tarracing or cement concrete, including flashings and junction of parapets and complete removing debris and rubbish from site, including roughening the surfaces of old concrete including picking, sweeping, clean, washing down with water to remove dust and brushing neat cement slurry @ 3kg of cement per sqm including 25 mm thick PCC 1:2:4 type B-01 using 12.5 mm graded crushed stone aggregate as in roof including finishing the surface even and rough and including rendering 20mm thick in cement mortar 1:4 mixed with water proofing admixture (as per manufacturars instruction) and priming surfaces and applying normal treatment (for moderate conditions) using glass fibre base bitumen felt, Grade-2 and laying of APP based polymeric membrane minimum weighing 3.0 Kgs/sqm and minimum 3mm thick reinforced with polyster non woven fabric (wt not less than 150 gms/sqm) laid on primed surface by forced application complete all as specified laid over a coat of bituminous primer @0.3 ltr/sqm and finished with applying bitumen grade 85/25 coat @1.2 Kg/sqm. APP membrane shall be laid by torching with 75mm overlap in longitudnal direction complete all as specified and directed by Engr-in-Charge. The products of the following firms shall be used for water proofing membrane: - MAKE: (a) "Hyper Plus Standard" (b) "Multi Plus" (c) Bengal Acquaflux-Bengal Bitumen" (d) "Superior Poly Plus S-30"

M&L broken stone and boulders hardcore of gauge n exc 63 mm, deposited, spread and levelled in layers n exc 15 cm thick water and rammed to a true surface complete all as specified and directed.

M & L Non-Skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11sqm not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed or bedding layer in Cement Mortar 1:4 for laying floor finishes complete all as specified and directed. MAKE: KAJARIA/H&R JOHNSON/CERA/ NITCO/SOMANY

Taking down carefully copper/Aluminum point wiring (Light, Fan, Socket or power) complete fitting such as switches, ceiling, regulator, sockets etc removing materials to be store for keeping in safe custody for taking credit and making good disturbed surfaces of walls, floors etc as directed.

M&L for point wiring for one light point/exhaust fan point controlled by one switch with PVC insulated copper conductor stranded cable of size 1.5 sqmm and including PVC casing/caping terminated in existing sunk CI/pressed steel terminal boxes for fixing and 1.5 sqmm PVC insulated copper wire as earth wire connected to earth wire connected to earth folly and 3.0mm thick plastic laminated sheet cover all as specified and directed by Engr-in-Charge. Make of cable: L&T/FINOLEX/GRANDPLAY/ANCHOR/ POLYCAB Make of casing caping PLAZA/FINOLEX/ SUPREME/PRESTO PLAST

All as per Item No 81.00 but for one switch socket outlet 6 Amps, 230 volts point on the same board

All as per Item No 81.00 but for one switch socket outlet 6 Amps, 230 volts point on independent board

All as per ser Item No 81.00 but for point wiring with 4 sq mm PVC insulated, unsheathed single core stranded copper conductor 1100 Volt grade in PVC capping cassing on wall /floor etc with all accessories of suitable size MS/Pressed steel terminal boxes 1.6 mm thk with bakelite sheet cover (hylum) 3mm thick /PVC Gang box for mounting switch, socket, Cup washers complete with all accessories for one 6 pin 15 Amp socket outlet point on independent board including 4 sqmm PVC insulated copper conductor in green colour common earth and connecting to earth dolly all as specified. Make of cable: L&T/FINOLEX/GRANDPLAY/ANCHOR/ POLYCAB Make of casing caping PLAZA/FINOLEX/ SUPREME/PRESTO PLAST

M&L for lamp holder PVC/Polycarbonate type insulated body with back plate suitable for batten fittings as specified and directed. Make : Anchor/Legrand/Crabtree/Cona

S&F switch piano flush type one way single pole 6 Amp 240 volts. Make : Anchor/Legrand/Crabtree/Cona

S&F for switch socket combination outlet 5pin, 6A, 240 volts flush type complete all as specified and as directed. Make : Anchor/Legrand/Crabtree/Cona

S&F for switch socket combination outlet 5pin, 6Amp and 16 Amp, 240 volts flush type complete all as specified and as directed. Make : Anchor/Legrand/Crabtree/Cona

M&L for ceiling rose surface bakelite 65x50 mm two to three terminals.all as specified and directed by Engr-in-charge. Make : Anchor/Legrand/Crabtree/Cona

S&F in replacement MCB distribution board double door, regal grey, sheet metal enclosure, SPN 240 volts 8 way with 200 amps rated bus bar concealed to wall and making flush with wall surfaces and making good to disturbed surfaces of walls to match with the exisiting surface etc complete all as specified and directed. Make: Cat part No 5076 11 of Legrand (Ekinoxe) or equal approved in Schneider (Acti-9)/Siemens (Betagard-8GB32)

Supply and fixing MCB SPN 63 Amps, 'C' series, 230 V A/C complete incl taking down old MCBs all as specified and as directed by Engineer-in-Charge. Make: Cat part No 4086 20 of Legrand (DX³) or equal approved in Schneider (Acti -9)/ Siemens (Betagard-5SL4)

S&F in replacement MCB SPN 40 Amps, 'C' series, 230 V, AC complete all as specified and as directed by Engineer-in-Charge. Make: Cat part No 4086 18 of Legrand (DX³) or equal approved in Schneider (Acti -9)/ Siemens (Betagard-5SL4)

S&F in replacement MCB SP 6 to 32 Amps, 'C' series, 230 V A/C complete incl taking down old MCBs all as specified and as directed by Engineer-in-Charge. Make: Cat part No 4085 87 to 4085 95 of Legrand (DX³) or equal approved in Schneider (Acti -9)/ Siemens (Betagard-5SL4)

S&F in replacement of Skylux LED 36watts recessed 2'x2' luminaire to enhance the delight of occupants with comfortable experience through its design & glare free soft illumination and connection of 3 core copper wire with all accessories(Warm White) Make : Cat part No -BZRSQL 36 W GZi W (Natural White) of Bajaj or equivalent in Havells/Philips.

Material and labour for earthing complete with galvanised steel earth plate 600 x 600 x 6 mm buried directly in ground vertically to a depth not less than 2.25 metre below normal ground level with top edge of the earth plate at a depth not less than 1.5 metre below ground level connected to and including GI wire of size 4 mm dia by means of nuts, bolts, washers etc made of and connected to test point and earth dolly as all shown in electrical plate No.3 of SSR Part-I 2009 and specified or indicated including excavation and earth work in any type of soil PCC (1:3:6) type C1 in chamber, pre cast RCC slab 50mm thick in cement concrete (1:2:4) type B1, reinforced with welded steel wire fabric or XPM jali (weight not less than 4.0 kg/Sqm) with cast iron frame, funnel, with wire mesh, 20mm bore light grade GI watering pipe, lugs, 15mm bore light grade GI protection pipe, test point etc including taking down old earthing material complete all as specified and as directed. Note: (i) Item includes the cost of 7.5 m GI pipe for protection of earth lead. Any additional length shall be adjusted through deviation order. (ii) Item includes the cost of 7.5 m GI earth lead. Any additional in length shall be adjusted through deviation order (iii) Item includes the cost of Charcoal and commercial salt

Sub main wiring with two runs of 6 Sqmm (2x6sqmm) 1100 volts grade single core FRLS PVC insulated unsheathed multistranded copper conductor confirming to IS-694 drawn through and including non-metalic PVC casing caping ISI marked with all accessories etc with one run of 6 Sqmm (1x6sqmm) single core FRLS PVC insulated unsheathed copper conductor cable as earth wire and making good to match with existing surfaces incluidng taking down old wiring complete all as specified and directed by Engineer-in-Charge. Note:- 2 runs of 6Sqmm (2x6sqmm), one run of 6 Sqmm (1x6 sqmm) cable and one metre of PVC casing caping will be measured as one unit. Make of cable: L&T/FINOLEX/GRANDPLAY/ANCHOR/ POLYCAB Make of casing caping : PLAZA/FINOLEX/ SUPREME/PRESTO PLAST

Sub main wiring with two runs of 10 Sqmm (2x10sqmm) 1100 volts grade single core FRLS PVC insulated unsheathed multistranded copper conductor confirming to IS-694 drawn through and including non-metalic PVC casing caping ISI marked with all accessories etc with one run of 6 Sqmm (1x6sqmm) single core FRLS PVC insulated unsheathed copper conductor cable as earth wire and making good to match with existing surfaces incluidng taking down old wiring complete all as specified and directed by Engineer-in-Charge. Note:- 2 runs of 10Sqmm (2x10sqmm), one run of 6 Sqmm (1x6 sqmm) cable and one metre of PVC casing caping will be measured as one unit. Make of cable: L&T/FINOLEX/GRANDPLAY/ANCHOR/ POLYCAB Make of casing caping : PLAZA/FINOLEX/ SUPREME/PRESTO PLAST

S&F in replacment LED lights fitting 1x20 watt, 220 volts, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. Make : Cat part No LHEXAOP7PN1W020 of Havells/ Philips/Bajaj/ Crompton

S&F in replacment LED lights fitting 1x16 watt, 220 volts, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. Make : Havells/ Philips/Bajaj/ Crompton

Supply and fixing in replacement of TPN vertical double door DBs 04 way provision for FP MCCB 'G' frame upto 200 Amp incoming 25 KA complete all as specified and directed by Engr-in-Charge. Make : Cat Part No. DHDLVDRWGOFOO4 of Havells or equivalent in L&T/Legrand/Siemens

Supply and fixing MCCB 4 pole 160 Amps, 16 KA, 415 Volt complete incl taking down of old MCCBs all as specified and as directed by Engineer-in-Charge. Make: Legrand (DPX³) or equal approved in Schneider (NSX)/ Siemens (3VL2)/L&T (D-Shine)

S&F in replacement of sheet metal enclosure with 20 amp, 240 Volts socket plug top and MCBs single pole and neutral enclousre with two pin and earth plug and socket with one single pole 20 amp MCB complete all as specified and directed by Engr-in-Charge Make: Legrand/Schneider/Siemens /L&T

S&F in replacement of sheet metal enclosure with 20 amp, 415 Volts socket plug top and MCBs single pole and neutral enclousre with two pin and earth plug and socket with one single pole 20 amp MCB TP complete all as specified and directed by Engr-in-Charge Make: Legrand/Schneider/Siemens /L&T

S&F 1100 V grade heavy duty cable PVC insulated aluminium conductor served with inner sheathing of pvc tape and over all pvc sheathed in service connection suspended by insulating hangers not more than 1 mtr apart including 4 mm suspension wire one twin core cable flat of stranded multistrand conductor size 10 sqmm, 2 core complete all as specified and directed by Engr-in-Charge Make : Havells/L&T/Finolex/Anchor/Ploycab

Taking down carefully DG set of 35 KVA by unscrewing nuts and bolts from its base mounting and lifing up both the Gen sets with hydrolic crane in lorry and transporting to work shop for repiar dismantling tapped cover, cylinder head assembly, engine block, removing piston assembly, connecting rods assembly, cleaning servicing and overhouling to engine, grinding cranck as per required size, resurfacing cylinder head assembly, replacing & grinding valve seats, replacing cylinder liner and piston assembly, adjusting tapped gap and rocker arm assembly, re assembling all the dismantled components to its original position size including testing the machine to its optimum efficiency to the entire satisfaction and directed by Engr-in-Charge for the following capacity of Gen sets. Note : Replacement of spares in engine repairing shall be measured and paid separately under sch relevant items and labour cost for replacement of spares shall be deemed to be inclusive in rates quoted for sch item Ser No 1

Taking down carefully alternator 35 KVA, 415 Volt, 3 phase, 4 wire system designed on 0.8 power factor and 1500 RPM by unscrewing and disconnecting coupling shaft from prime mover side, opening winding shell, cleaning, removing burnt field and starter winding, cleaning, sevicing and re winding the field and starter winding with super enamel copper strip/conductor of existing gauge, varnishing, heating/baking including re assembling all the dismantled component position with testing alternator to its optimum efficiency i.e. 415 volt out put at 1500 RPM at 0.8 PF to the entire satisfaction of Engr-in-Charge

M&L for taking down carefully self starter assembly 12 Volt ,DC,dismantling ,removing burnt winding of field and armature ,cleaning, overhouling and rewinding with super enemal copper conductor of existing guage varnishing,heating/baking etc including re assembling all the dismantled components to its origional position with testing complete with replacing the following :- (a) Solenoid switch 12 volt,AC ,50 Hz - 01 Each (b) Clutch bendix pinion - 01 Each (c) Body bracing bolt - 02 Each (d) Battery lead with copper lugs (1.2 Mtr) - 01 Each (e) Battery terminal brass - 02 Each

M&L for reconditioning of existing unservicebale battery 12 Volt 180 Ampereshours by cutting and removing top cover cutting and removing burnt plates(cells) and draining out old electrolite liquid ,replacing cell /Plates of existing sizes ,refilling electrolite upto the required level with specific gravity ie 1250MM including charging the battery for 72 hours and trickle discharge it and repeat the process of charging with testing complete to the entire satisfaction of Engr-in-Charge.

Supply only engine exhaust outlet /inlet valve suitable for Gen Set 35 KVA complete.

Supply only cylinder head gasket suitable for Gen Set 35 KVA capacity

Supply only piston assembly suitable for gen Set 35 KVA complete. Make : Usha/Kirloskar

Supply only Piston ring and oil ring suitable for gen set 35 KVA complete. Make : Usha/Kirloskar

Supply only main bearing suitable for Gen Set 35 KVA complete. Make : Usha/Kirloskar

Supply only small and big end connecting bearing suitable for 35 KVA complete. Make : Usha/Kirloskar

Supply only oil seals off sizes suitable for Gen Set 35 KVA complete

Supply only antivibration pad suitable for Gen Set of 35 KVA Complete.

Supply only V fan belt suitable for Gen Set 35 KVA complete. Make : Fenner or equivalent

Supply only rubber radiator hose pipe suitable for Gen Set 35 KVA Complete.

M&L for taking down carefully FIP assembly of 35 KVA Gen Set by unscrewing nuts and bolts from its mounting dismantling cleaning ,replacing gaskets set ,feed pump,plunger and spring with overhouling and calibrating injector nozles at rquired temperature and pressure as per prevailing climatic contiondition and MSL in this hilly terrain for proper fuel combustion and functioning at optimum efficiency including re assembling al the dismantled components to its origional position all as specified and directed to the entire satisfaction of Engr-in-Charge.

Supply only fuel filter (primary & Secoundary )element suitable for gen set 35 KVA complete. Make : Purolator/Kirloskar

Supply only Engine main bearing suitable for Gen Set 35 KVA complete. Make : Usha/Kirloskar

Supply only V fan belt suitable for Gen Set 35 KVA complete.Make : Fenner or equivalent

Supply only thermostat valve suitable for radiator 35 KVA Gen Set

Supply only engine oil multigrade castrol suitable and recommended by manufactures ie Kirloskar engine . Make : HP/Castrol

M&L for prepration of old painted surface of DG Sets of any capacity by removing all dirt, dust, grease ol etc and painting of any capacity of DG Sets surface including connected accessories with one coat of synthetic enamel paint of approved colour complete all as directed by Engr-in-Charge.

Supply and fix Flywheel assembly suitable for Gen set 35 KVA complete all as spd and directed by Engineer-in-Charge

M&L for servicing of radiator assembly f capacity 35 KVA complete for cleaning, cooling water spaces, and replace unserviceable rubber hose, pipes, circlip,clamps, cleaning of radiator mix with appropriate cleaning agent , de-scaling by means of scale solvent as well as neutralizing agent to arrest leakage by means of brazing etc. all as directed by Engineer-in-charge of followig capacities :

Repair and replacement of 35 KVA DG Set Dyanomo/Alternator Assy for the following capacity DG sets complete all as spd and directed by Engr-in-Charge. Make :- Kirloskar/Cummins/Greaves/Mahindra

S&F in replacement of automatic voltage regulator (AVR) 24 volts suitable for 35 KVA Make : Cummins/Kirloskar

S&Fixing in replacemnt of water pump assembly of capacity35 KVA DG Set for folowing capacity DG Sets complete all as spd and direced by EIC. Make - Kirloskar/Cummins/Greaves/Mahindra

Taking down carefully DG Set of 320 KVA by unscrewing nuts and bolts from its base mounting and lifting up both the Gen Sets with hydrolic crane in lorry and transpoting to work shop for repair dismantling tapped cover ,cylinder head assembly ,engine block ,removing piston assembly,connecting rods assembly, cleaning ,servicing and overhouling to engine ,grinding cranck as per required size ,resurfacing cylinder head assembly ,replacing & grinding valve seats, replacing cylinder liner and piston assembly,adjusting tapped gap and rocker arm assembly , re assembling all the dismantled components to its origional position size including testing the machnine to its optimum efficiency to the entire satisfaction and idrected by Engr-in-Charge for the following capacity of Gen Sets :- NOTE : Replacement of spares in engine repairing shall be measured and paid seprately under sch relevent items and labour cost for replacement of spares shall be deemed to be inclusive in rates quoted for sch item ser No 1.

Taking down carefully alternator 320 KVA volt ,3 phase ,4 wire system desined on 0.8 power factor and 1500 RPM by unscrewing and disconnecting coupling shaft from prime mover side ,opening winding shell ,cleaning ,removing burnt field and stator winding ,cleaning ,servicing and re winding the field and stator winding with supper enamel copper strip/conductor of existing gauge ,varnishing, heating/baking including re assembling all the dismantled component to its origional position with testing alternator to its optimum efficiency ie 415 volt out put at 1500 RPM at 0.8 PF to the entire satisfaction of Engr-in-Charge

M&L for taking down carefully self starter assembly 12 Volt ,DC,dismantling ,removing burnt winding of field and armature ,cleaning, overhouling and rewinding with super enemal copper conductor of existing guage varnishing,heating/baking etc including re assembling all the dismantled components to its origional position with testing complete with replacing the following :- (a) Solenoid switch 12 volt,AC ,50 Hz -01 Each (b) Clutch bendix pinion -01 Each (c) Body bracing bolt -02 Each (d) Battery lead with copper lugs (1.2 Mtr) -01 Each (e) Battery terminal brass - 02 Each

M&L for reconditioning of existing unservicebale battery 12 Volt 180 Ampereshours by cutting and removing top cover cutting and removing burnt plates(cells) and draining out old electrolite liquid ,replacing cell /Plates of existing sizes ,refilling electrolite upto the required level with specific gravity ie 1250MM including charging the battery for 72 hours and trickle discharge it and repeat the process of charging with testing complete to the entire satisfaction of Engr-in-Charge.

Supply only engine exhaust outlet /inlet valve suitable for Gen Set 320 KVAcomplete

Supply only cylinder head gasket suitable for Gen Set 320 KVA capacity

Supply only piston assembly suitable for gen Set 320 KVA complete. Make : Usha/Kirloskar

Supply only Piston ring and oil ring suitable for gen set 320 KVA complete. Make : Usha/Kirloskar

Supply only main bearing suitable for Gen Set 320 KVA complete. Make : Usha/Kirloskar

Supply only small and big end connecting bearing suitable for 320 KVA complete. Make : Usha/Kirloskar

Supply only oil seals off sizes suitable for Gen Set 320 KVA complete

Supply only antivibration pad suitable for Gen Set of 320 KVA Complete.

Supply only V fan belt suitable for Gen Set 320 KVA complete.Make : Fenner or equivalent

Supply only rubber radiator hose pipe suitable for Gen Set 320 KVA Complete.

M&L for taking down carefully FIP assembly of 320 KVA Gen Set by unscrewing nuts and bolts from its mounting dismantling cleaning ,replacing gaskets set ,feed pump,plunger and spring with overhouling and calibrating injector nozles at rquired temperature and pressure as per prevailing climatic contiondition and MSL in this hilly terrain for proper fuel combustion and functioning at optimum efficiency including re assembling al the dismantled components to its origional position all as specified and directed to the entire satisfaction of Engr-in-Charge.

Supply only fuel filter (primary & Secoundary )element suitable for gen set 320 KVA complete. Make : Purolator/Kirloskar

_______ BLANK____________

_______ BLANK____________

Supply only thermostat valve suitable for radiator 320 KVA Gen Set

Supply only engine oil multigrade castrol suitable and recommended by manufactures ie Kirloskar engine . Make : HP/

M&L for prepration of old painted surface of DG Sets of any capacity by removing all dirt, dust, grease ol etc and painting of any capacity of DG Sets surface including connected accessories with one coat of synthetic enamel paint of approved colour complete all as directed by Engr-in-Charge.

Supply and fix Flywheel assembly suitable for 320 KVA complete all as spd and directed by Engineer-in-Charge

M&L for servicing of radiator assembly of capacity 320 KVA complete for cleaning, cooling water spaces, and replace unserviceable rubber hose, pipes, circlip,clamps, cleaning of radiator mix with appropriate cleaning agent , de-scaling by means of scale solvent as well as neutralizing agent to arrest leakage by means of brazing etc. all as directed by Engineer-in-charge.

Repair and replacement of Dyanomo/Alternator Assy for 320 KVA capacity DG sets Make :- Kirloskar/Cummins/Greaves/Mahindra complete all as spd and directed by Engr-in-Charge.

S&F in replacement of automatic voltage regulator (AVR) 24 volts suitable for 320 KVA DG Sets Make : Cummins/Kirloskar

S&Fixing in replacemnt of water pump assembly for folowing capacity 320 DG Sets Make - Kirloskar/Cummins/Greaves/Mahindra complete all as spd and direced by EIC.

Taking down carefully DG Set of 200 KVA by unscrewing nuts and bolts from its base mounting and lifting up both the Gen Sets with hydrolic crane in lorry and transpoting to work shop for repair dismantling tapped cover ,cylinder head assembly ,engine block ,removing piston assembly,connecting rods assembly, cleaning ,servicing and overhouling to engine ,grinding cranck as per required size ,resurfacing cylinder head assembly ,replacing & grinding valve seats, replacing cylinder liner and piston assembly,adjusting tapped gap and rocker arm assembly , re assembling all the dismantled components to its origional position size including testing the machnine to its optimum efficiency to the entire satisfaction and idrected by Engr-in-Charge for the following capacity of Gen Sets :- NOTE : Replacement of spares in engine repairing shall be measured and paid seprately under sch relevent items and labour cost for replacement of spares shall be deemed to be inclusive in rates quoted for sch item ser No 1.

Taking down carefully alternator 200 KVA volt ,3 phase ,4 wire system desined on 0.8 power factor and 1500 RPM by unscrewing and disconnecting coupling shaft from prime mover side ,opening winding shell ,cleaning ,removing burnt field and stator winding ,cleaning ,servicing and re winding the field and stator winding with supper enamel copper strip/conductor of existing gauge ,varnishing, heating/baking including re assembling all the dismantled component to its origional position with testing alternator to its optimum efficiency ie 415 volt out put at 1500 RPM at 0.8 PF to the entire satisfaction of Engr-in-Charge

M&L for taking down carefully self starter assembly 12 Volt ,DC,dismantling ,removing burnt winding of field and armature ,cleaning, overhouling and rewinding with super enemal copper conductor of existing guage varnishing,heating/baking etc including re assembling all the dismantled components to its origional position with testing complete with replacing the following :- (a) Solenoid switch 12 volt,AC ,50 Hz -01 Each (b) Clutch bendix pinion -01 Each (c) Body bracing bolt -02 Each (d) Battery lead with copper lugs (1.2 Mtr) -01 Each (e) Battery terminal brass - 02 Each

M&L for reconditioning of existing unservicebale battery 12 Volt 180 Ampereshours by cutting and removing top cover cutting and removing burnt plates(cells) and draining out old electrolite liquid ,replacing cell /Plates of existing sizes ,refilling electrolite upto the required level with specific gravity ie 1250MM including charging the battery for 72 hours and trickle discharge it and repeat the process of charging with testing complete to the entire satisfaction of Engr-in-Charge.

Supply only engine exhaust outlet /inlet valve suitable for Gen Set 200 KVAcomplete

Supply only cylinder head gasket suitable for Gen Set 200 KVA capacity

Supply only piston assembly suitable for gen Set 200 KVA complete. Make : Usha/Kirloskar

Supply only Piston ring and oil ring suitable for gen set 200 KVA complete. Make : Usha/Kirloskar

Supply only main bearing suitable for Gen Set 200 KVA complete. Make : Usha/Kirloskar

Supply only small and big end connecting bearing suitable for 200 KVA complete. Make : Usha/Kirloskar

Supply only oil seals off sizes suitable for Gen Set 200 KVA complete

Supply only antivibration pad suitable for Gen Set of 200 KVA Complete.

Supply only V fan belt suitable for Gen Set 200 KVA complete.Make : Fenner or equivalent

Supply only rubber radiator hose pipe suitable for Gen Set 200 KVA Complete.

M&L for taking down carefully FIP assembly of 200 KVA Gen Set by unscrewing nuts and bolts from its mounting dismantling cleaning ,replacing gaskets set ,feed pump,plunger and spring with overhouling and calibrating injector nozles at rquired temperature and pressure as per prevailing climatic contiondition and MSL in this hilly terrain for proper fuel combustion and functioning at optimum efficiency including re assembling al the dismantled components to its origional position all as specified and directed to the entire satisfaction of Engr-in-Charge.

Supply only fuel filter (primary & Secoundary )element suitable for gen set 200 KVA complete. Make : Purolator/Kirloskar

_______ BLANK____________

Supply only V fan belt suitable for Gen Set 200 KVA complete.Make : Fenner or equivalent

Supply only thermostat valve suitable for radiator 200 KVA Gen Set

Supply only engine oil multigrade castrol suitable and recommended by manufactures ie Kirloskar engine . Make : HP/

M&L for prepration of old painted surface of DG Sets of any capacity by removing all dirt, dust, grease ol etc and painting of any capacity of DG Sets surface including connected accessories with one coat of synthetic enamel paint of approved colour complete all as directed by Engr-in-Charge.

Supply and fix Flywheel assembly suitable for 200 KVA complete all as spd and directed by Engineer-in-Charge

M&L for servicing of radiator assembly of capacity 200 KVA complete for cleaning, cooling water spaces, and replace unserviceable rubber hose, pipes, circlip,clamps, cleaning of radiator mix with appropriate cleaning agent , de-scaling by means of scale solvent as well as neutralizing agent to arrest leakage by means of brazing etc. all as directed by Engineer-in-charge.

Repair and replacement of Dyanomo/Alternator Assy for the following capacity DG sets Make :- Kirloskar/Cummins/Greaves/Mahindra complete all as spd and directed by Engr-in-Charge.

S&F in replacement of automatic voltage regulator (AVR) 24 volts suitable for 200 KVA DG Sets Make : Cummins/Kirloskar

S&Fixing in replacemnt of water pump assembly for folowing capacity DG Sets Make - Kirloskar/Cummins/Greaves/Mahindra complete all as spd and direced by EIC.

Horizon Construction Company

Mehar Enterprises