PROVIDING 1 NO. 200 KVA TRANSFORMER, HT/LT LINE AND STREET LIGHT WORK IN SHOPPING CENTRE ADJOINING DHARAMSHALA (MANDI TOWNSHIP) U/E KAITHAL. (INCLUDING SIX YEARS DEFECT LIABILITY PERIOD FOR TRANSFORMER AND THREE YEARS FREE MTC. and DEFECT LIABILITY P

[13.32]Providing and fixing bolts including nuts and washers complete. [Through Rate]

[23.22.1.9]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 1.9. Supply and erection of Modular case circuit breaker single pole/4 pole on existing wall/pedestal/Panel including bounding to earth and making necessary connections required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the work. 4 pole MCCB 6 amp to 100 amp , 25 KA [Through Rate]

[23.24.3.9]MS STAND, BUS BAR CHAMBER AND PANELS 3.9. Supply and erection of metal clad bus bar chamber made from 1.6 mm thick M.S. sheet and fixing with rag bolts on wall or on existing pedestal/angle iron frame including bonding, detachable top and bottom including painting and necessary connection etc. (Aluminium bars). 300 amp 4 bars of 100 cm each (cross section 51 mm x 6 mm) chamber over all size 1.10 m x 55 cm x 23 cm [Through Rate]

[23.27.5]Supply and erection of Godrej Almirah typeM.S. pedestal made of 50 mm x 50 mm x 6 mm angle iron frame with 3.00 mm thick M.S. sheet covering including shutters with suitable hinges and locking arrangement with Godrej type handle including round bars . The top covering should have downward overhang of 75 mm on all sides of pedestal , having two sets of water proof ventilation holes of suitable size on the sides , at top and bottom , each set containing four Nos. holes to discharge the heat produced by the current . The shutters fixed with rubber gasket of superior quality and of suitable size to make it water proof . The pedestal duly painted both inside and outside with two coats of approved paint and primary coat and its legs are embeded upto the entire depth in 1:2:4 cement concrete block , projected 75 mm all around the pedestal and and 200 mm above the ground level including the cost of all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-in-charge of the work:- 5. M.S. pedestal of size 1200 mm wide ,1500 mm high ,450 mm deep and bottom totally open , duly embeded in cement concrete block of size 1350 mm x 600 mm x 200 mm above ground level , having a base of size 1500 mm x 750 mm x 250 mm below ground level . 0 0 [Through Rate]

[24.1.1]EARTHING AND LIGHTENING ARRESTOR 1. Earthing with GL earth pipe 4.5 m long and 40 mm dia with masonry enclosures on the top etc. (but without charcoal or coke and salt) as required. [Through Rate]

[24.1.2]EARTHING AND LIGHTENING ARRESTOR 2. Extra for using salt and char coal/coke for pipe earth electrode as required. [Through Rate]

[24.1.8]EARTHING AND LIGHTENING ARRESTOR 8. Providing and fixing 25 mm x 3mm G.I. strip on surface or in recess for connections etc. as required with all labour and material. [Through Rate]

[24.13.24]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING& ERECTION/ LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR UNDERGROUND CABLE LOOSE IN EXISTING PIPE OR TRENCHES COMPLETE IN ALL RESPECT WITH NECESSARY CONNECTION UPTO THE ENTIRE SATISFACTION OF ENGINEER IN CHARGE OF THE WORK 24. 16 Sq mm 4 core (Arm.) [Through Rate]

[24.13.25]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING& ERECTION/ LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR UNDERGROUND CABLE LOOSE IN EXISTING PIPE OR TRENCHES COMPLETE IN ALL RESPECT WITH NECESSARY CONNECTION UPTO THE ENTIRE SATISFACTION OF ENGINEER IN CHARGE OF THE WORK 25. 25 Sq mm 2 core (UnArm.) [Through Rate]

[24.13.70]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING& ERECTION/ LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR UNDERGROUND CABLE LOOSE IN EXISTING PIPE OR TRENCHES COMPLETE IN ALL RESPECT WITH NECESSARY CONNECTION UPTO THE ENTIRE SATISFACTION OF ENGINEER IN CHARGE OF THE WORK 70. 120 Sq mm 3.5 core (Arm.) [Through Rate]

[24.4.3]STREET LIGHT 3. Supply and erection of 32mm dia metre 1.5 m long bracket (B-class) making an angle of 10° to 15° with horizontal plane for mounting street light fitting fixing of GI. bracket on wall with 2 nos. 32 mm x 3 mm thick M.S. clamps including cost of cutting, welding of G.I. pipe complete with cement sand mixture, bolts and nuts etc. including necessary connections. [Through Rate]

[24.5.1.1]MISCELLANEOUS ITEMS 1.1. Supply and jointing three core submersible flat cables of approved make with bare bunched copper conductor insulated and sheathed with PVC for submersible pump motors /fountain lights etc with voltage grade 1100 volts marked with IS:694, 1990 including cost of jointing, materials as well as carriage, loading, unloading etc. complete in all respect up to the entire satisfaction of Engineer- in-Charge. Submersible Copper Cable 3 Core 1.5 sqmm [Through Rate]

[24.5.1.2]MISCELLANEOUS ITEMS 1.2. Supply and jointing three core submersible flat cables of approved make with bare bunched copper conductor insulated and sheathed with PVC for submersible pump motors /fountain lights etc with voltage grade 1100 volts marked with IS:694, 1990 including cost of jointing, materials as well as carriage, loading, unloading etc. complete in all respect up to the entire satisfaction of Engineer- in-Charge. Submersible Copper Cable 3 Core 2.5 sqmm [Through Rate]

[24.5.2.3]MISCELLANEOUS ITEMS 2.3. S/E mark double walled corrugated (DWC) HDPE, pipe 10 Kg/Cm2 ,laid 0.75 Metre below ground level including digging and refilling of earth including cost of suitable size socket/coupler for HDPE pipe including the cost of labour and material required to complete the job in all respect up to the entire satisfaction of Engineer in charge of the work. DWC/HDPE pipe 63/50 mm outer dia/inner dia [Through Rate]

Supply and Erection of LT PVC unarmoured cable of size 300 Sqmm single core with aluminium conductor 650/1100 V conforming to ISS 1554 (Part-I) of 1988 IS: 7098/Part-1/ 1988 with latest amendments up to entire satisfaction of Engineer-in-charge (Make: Grandlay, Polycab, Havells, CIRTINA (Excluding GST 18%).

Supply and Erection of G.I. V shape cross arm suitable for 11 KV system made out of G.I. channel of size 100x50x50x6mm (ICMC100) as per design and drawing of UHBVN 13.2 kg. 2 Nos. 18mm dia holes provided in the base for fixing of half clamp 2 Nos. holes 22mm dia for GI pin on the flange shall be provided on the top and bottom flanges of both end of V-shape X-arm complete in all respect (Excluding GST 18%).

Supply, installation, testing, commissioning of 3 Phase 11KV/0.433 KV-250V, 200 KVA Oil immersed, naturally cooled, Aluminum Wound Outdoor type Distribution Transformers with CSP (Completely self protected ) features with external microprocessor based four pole MCCB 300 Amp. To 400Amp., 50kA strictly conforming to Nigam’s technical specification No. CSC-V/R-I/DH/UH/P and D/2010-2011 read with amendment thereof and as per relevant ISS as amended from time to time and losses conforming to 4 star rating of BEE as per Appd. Make and Specification of UHBVN/UHBVN including installation of transformer on existing platform up to the entire satisfaction of Engineer-in-Charge. (Excluding GST 18%) Voltage Rated Frequency Permitted at 75ºC i) Maximum load losses at 50% load at 75ºC = 780 Watt ii) Maximum losses at 100% load at 75ºC = 2300 Watt iii) Warranty = 72 Months shall be one time The above losses are maximum allowable and there would not be any positive tolerance. (Excluding GST 18%)

Supply and Erection of 11 kV G.O. Switch vertical mounted with a heavy duty 9 Nos. post insulators suitable copper male and female contacts fixed on GI angle frame with G.I. Nut and Bolts including G.I. pipe and operating handle complete in all respect (Excluding GST 18%)

Supply and erection of 11kV Lightning Arrester as per approved makes and relevant specifications of UHBVN complete fixing with GI clamp, Nut and bolts up to entire satisfaction of Engineer-In-Charge (Ex-GST 18%)

Supply and Erection of 11kV polymeric Pin insulator 10 kN with GI Pin of approved makes / specification of UHBVN (Ex-GST 18%)

Supply and Erection of ACSR conductor 50 mm2 conforming to IS 398 (Part-II) 1976/1996, IS 4826-1976 IS 1521-1972 and IS 1778-1980 with latest amendments as per UHBVN specification including stringing and sagging as well as jointing and binding with insulators at supports complete in all respect upto the entire satisfaction of Engineer-in-Charge (Ex-GST 18%)

Supply and Erection of ACSR conductor 80 mm2 conforming to IS 398 (Part-II) 1976/1996, IS 4826-1976 IS 1521-1972 and IS 1778-1980 with latest amendments as per UHBVN specification including stringing and sagging as well as jointing and binding with insulators at supports complete in all respect upto the entire satisfaction of Engineer-in-Charge (Ex-GST 18%)

Supply and Erection of ACSR conductor 30 mm2 PVC insulated conforming to IS 398 (Part-II) 1976/1996, IS 4826-1976 IS 1521-1972 and IS 1778-1980 with latest amendments as per UHBVN specification including stringing and sagging as well as jointing and binding with insulators at supports complete in all respect upto the entire satisfaction of Engineer-in-Charge (Ex-GST 18%)

Supply and Erection of fuse unit of L.T. side suitable for 200 kVA transformer complete with wooden board, aluminium bus bar GI clamps and GI nut and bolts including all petty material required up to the entire satisfaction of Engineer-in-charge (Ex-GST 18%)

Supply and Erection of wooden cleats of size 4” wide 1’-6” long complete with 4 Nos. holes suitable to pass through 300/400 Sqmm single core cable complete in all respect upto the entire satisfaction of Engineer-in-charge (Ex-GST 18%)

Supply and Erection of Danger plate enameled with clamp for 11 KV/33 KV line as per UHBVN specification complete in all respect (Ex-GST 18%)

Supply and Erection of 9Mtr. Long PCC pole as per IS:1678-1960 specifications, 9Mtr. Long 105mm x 115mm at top and 105mm × 315mm at bottom with a working load of 200 Kg. buried 1.80 M in ground or as UHBVNL specification. (Ex-GST 18%).

Supply and Erection of 11 Mtr. Long PCC pole as per IS:1678-1960 specifications,11Mtr. Long 140mm x 200mm at top and 140mm × 400mm at bottom with working load of 400 Kg buried 2.20 M in ground as per UHBVNL specification.(Ex-GST 18%).

Supply and Erection of 11 KV polymeric disc insulator 45 KN for 11 KV overhead lines with fittings, TandC type and complete with galvanized strain clamps, bolts, nuts, washers etc. as required as per UHBVN specification (Ex-GST 18%)

Supply and Erection of Stay set for HT line complete with GSS 7/8 SWG, Egg, insulator/ Disc Insulator, GI rod 20mm dia threaded up to 250mm length with Nut (wt.6.224kg), cross plate 460 mm of Channel 75×40×6mm (wt.5.330kg), Elbow (wt.2.240kg), clamp with Nut-Bolts etc. as per UHBVN specification complete in all respect up to the entire satisfaction of Engineer-in-charge. (Ex-GST 18%).

Supply and Erection of Stay set for LT line complete with GSS 7/8 SWG, Egg, insulator/ Disc Insulator, GI rod 20mm dia threaded up to 250mm length with Nut (wt.6.224kg), cross plate 460 mm of Channel 75×40×6mm (wt.5.330kg), Elbow (wt.2.240kg), clamp with Nut-Bolts etc. as per UHBVN specification complete in all respect up to the entire satisfaction of Engineer-in-charge. (Ex-GST 18%).

Supply and Erection of HT Cradle Guard made of GI wire of SWG including fixing in 11kV line complete in all respect up to the entire satisfaction of the Engineer-In-Charge. (Ex-GST 18%).

Supply and Erection of LT Cradle Guard / Guard Reel made of GI wire of SWG including fixing in 11kV line complete in all respect up to the entire satisfaction of the Engineer-In-Charge. (Ex-GST 18%).

Supply and Erection of Galvanized steel item (Flat, Angle, Channel) and Nut and Bolts etc. including cutting, bending to the required shape, drilling hole, carriage, loading-unloading complete in all respect up to the entire satisfaction of Engineer-in-charge.(Ex-GST 18%).

Supply, Stringing and Sagging 8 SWG G.I. Earth wire complete in all respect to the entire satisfaction of Engineer-in-charge conforming to IS 298/1978 and 7807/1973 and with latest amendment thereof. (Ex-GST 18%).

Supply and Erection of GI D-Strap as per UHBVN design and specifications complete in all respect up to the entire satisfaction of Engineer-In-Charge (Ex-GST 18%)

Supply and Erection of shackle insulator as per UHBVN specification complete in all respect (Ex-GST 18%)

Supply and Erection of 25 Watt pressure die cast aluminum housing LED street light fitting luminaire with multiple LED lenses and heat resistant polycarbonate. Cover glass IP65 of complete in all respect as per specifications having light efficiency of 120 lumens / watt up to the entire satisfaction of Engineer-in-charge of the work Make: Bajaj / Philips / LT (with 3 year free replacement warranty, mtc. including labour charges, free of cost). (Ex-GST 18%)

Supply and Erection of M.S. earthing rod of 20mm dia and 2.5 mtr. long tapered to point at one end over a length of 50 mm and other end flattened to 40 mm width over a length of 150 mm and half portion having two holes of 12 mm dia., 50 mm apart with 25 mm dia., 16 SWG thick, 3 mtr. long M.S. pipe (conforming to IS 9537(Part-1) painted with black enameled paint complete in all respect up to the entire satisfaction of The Engineer-In-Charge. (Ex-GST).

Supply and Erection of top hamper suitable for 11 Mtr. Long PCC pole and 11kV system made out of GI flat size 50×6mm (A shapes) having weight 2.95 kg as per approved design and drawing of UHBVN complete in all respect (Ex-GST 18%)

Supply and Erection of L.T spacer (Poly Poline type) 4 wire line spacer on the existing L.T. line including the cost of all labour required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge.

S/E of 200 Watt LED Flood light luminaries of with multiple LED with highly efficient high power LED light with lens, pressure die cast aluminum housing, reflector and enclosed with toughened glass, IP-66 level as per specification attached. (With 3 years free replacement warranty at site including labour charges free of cost). (Make: Philips/Bajaj/LT/Panasoni) (Excluding GST}

Supply, erection, testing and commissioning of ELEX-TWS-2EXT/Amson`s/LandT make Automatic electric timer to switch ON/OFF the street light automatically. It should have adjustable lux level switch, with extensible mountable sensor. It shall change ON/OFF timing automatically as per lux level of the Sun at sun-rising and sun setting, throughout the year. Shall have two Nos. LandT make, 3 pole power contactor model MNX-70 to control 70 amp per phase with 220 Volt coils. It shall have auto/manual switch for repair of street light during day time. The whole unit components to be assembled on Bakelite sheet with 16 amp capacity MCB to save the time switch. The erection of the complete unit in the existing pedestal with complete wiring upto the entire satisfaction of the Engineer-in-charge. (Excluding GST)

Trenchless horizontal boring 1 Mtr. below ground level including the cost of HDPE pipe suitable for the HDPE pipe of various sizes complete in all respect up-to the Entire satisfaction of Engineer-In-Charge. (Excluding GST 18%)

Supply, Installation Testing and Commissioning of LED Street Light Fixture with Wattage range of (45 Watt) with body made of High Pressure Single Piece Die Cast Aluminum Alloy and cover made of PMMA (polymethymethacrylate) having system Lumen)120Ipw with inbuilt Protection against Short Circuit, Miswiring, Over Voltage and Surage Protection of 6 KV. The IP of fixture and Driver Comparment should be IP66 and same for the LED Comparment. The driving current should be ( 700mA with THD ( 5% and PF ). 90 and Operating Voltage between 120-270V and CRI ) 70 and Impact Resistance of IK)05. The specifications as mentioned above should be duly tested and Mentioned in LM79 Report from Govt. Approved NABL Accredited Labrotary and LM80 Report of LED Chip from the Manufacturer required to complete the job in all respect including erection on existing pole for fixing including connection of the same upto the entire satisfaction of Engineer-in-Charges of the work. (Warranty- 3 Years Including Driver against any manufacturing defect) (Including Three Years replacement warranty and three years Free Mtc./Defect Liability Period Free Of Cost). The logo of company should be embossed on the fixture. (Makes :- Bajaj/Phillip’s/Panasonic/LT). The fixture should comply with the parameter as per IS-10322 and IEC-60598. Excluding GST

Please Enable Macros to View BoQ information