PROVN OF 01BATH COMPLEX ALONGWITH 06 ATT TOILETS FOR ORS AT KARU AND PROVN OF MT PARKING SHED AT SHESHARTHANG AND SPL REPAIR TO BLDG NO T199 AND T205 AT TANGTSE AREA UNDER GE 860 EWS

Amount

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in any type of soil complete all as specified and directed by Engr-in-Charge.

Excavation in trenches n. exc. 1.5m wide and n. exc. 1.5m depth for foundation and getting out in hard/dense soil complete all as specified and directed by Engr-in-Charge.

M&L for plain cement concrete (PCC) type D2 1:4:8 (using 40mm graded crushed stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed by Engr-in-Charge.

M&L for reinforced cement concrete (RCC) Type B1 1:2:4 using 20mm graded aggregate as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed by Engr-in-Charge.

M&L for reinforced cement concrete Type B1 1:2:4 using 20mm graded crushed stone aggregate as in Columns, pillars, piers, posts and struts complete all as specified and directed by Engr-in-Charge.

M&L for reinforced cement concrete (RCC) nominal Mix Type B1 1:2:4 using 20mm graded crushed stone aggregate as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed by Engr-in-Charge.

M&L Steel sheet form work to sides of concrete foundations,footings, bases of columns raft and beams sides and soffits(if any) of foundations and plinth beams and similar work,vertical or to batter,for rough finished flat surfaces of concretecomplete all as specified and directed by Engr-in-Charge.

M&L for Steel sheet Formwork to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed by Engr-in-Charge.

M&L for Steel sheet formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc rough finished surfaces of concrete complete all as specified and directed by Engr-in-Charge.

M&L mild steel TMT bars 10mm dia and over cut to length, bent to shape required, including cranking bending spirally for hooping for columns hooking ends and binding with and including mild steel wire(annealed ) not less than 0.9mm dia or securing with clip complete all as specified and as directed.

M&L mild steel TMT bars 5mm dia and over upto and including 10mm dia as in stirrups, cut to length, bent to shape required, including cranking bending spirally for hooping for columns hooking ends and binding with and including mild steel wire(annealed ) not less than 0.9mm dia or securing with clip complete all as specified and directed by Engr-in-Charge.

M&L Precast cement concrete block masonry type C1 1:3:6 (20mm graded aggregate) with solid blocks, exc. 10cm in width and, setting in cement mortar 1:6 complete all as specified and directed by Engr-in-Charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed by Engr-in-Charge.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed by Engr-in-Charge.

M&L Hardcore of guage exc 63mm but n exc. 100 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface in broken stone or boulders complete all as specified and directed.

M&L for Cement Concrete type -D-2, 1:4:8 (using 40 mm graded crushed stone aggregate) 100mm thick as in Sub base complete all as specified and directed by Engr-in-Charge.

M&L machine cut kota stone slab flooring 20-25 mm thick over cement screed base laid and jointed with grey cemnt slurry mixed with pigment to match the shade of the slab including 20 mm thick screed bed cm 1:6, rubbing and polishing complete all as specified and directed by Engr in Charge.

M&L for Glazed ceramic tiles 450X 300X 7mm thick mm thick coloured/shaded as in vertical surfaces such as skirting dados etc set and jointed in neat cement slurry over 15 mm th backing coat in CM 1:4 and pointed in coloured cement to match the surface complete all as specified and directed by Engr-in-Charge.

M&L for Rendering 15mm thick in CM (1:4) using water proofing compound as per manufacturer's instruction in two layers, finished even and smooth surface without using extra cement complete all as specified and directed by Engr-in-Charge. Note: WPC shall be measured and paid separately.

M&L for preparation of new plastered surfaces and apply two coats of cement base paint over a coat of primer complete all as specified and directed by Engr-in-Charge.

M&L Rendering 10 mm thick on fair faces of brick work or concrete sur- faces in cement mortar 1:6 and to be finished even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.

Supply only water proofing compound for external plaster complete all as specified and directed by Engr-in-Charge.

S&F Vitreous china ( EWC) pedestal pan and trap , including connection to drain ( or outgoing pipe ) and to flushing pipe antisyphonage pipe, with seat cover etc complete including concrete and making good to floor. complete all as specified and directed by Engr-in-Charge.

S&F vitreous china water closet (Squatt Pan) Orrisa pattern 580x440 mm size pan white with front or back inlet with integral 'foot rests including provn of lime concrete bedding including connections to 'flushing cistern/pipe' complete all as specified and directed including 100mm CI/PVC 'P' trap.complete all as specified and directed by Engr-in-Charge.

S&F PVC low level white flushing cistern 10 litre capacity valve less, syphonic action type, complete with inlet, ball valve, float valve, bends, brackets, brass screws, handle etc with flush pipe of polyethylene of low density 32 mm dia of suitable length and making all connection complete all as specified and directed by Engr-in-Charge.

S&F tubular towel rail 20 mm dia,D type, 60 mm long between flanges complete all as specified and directed by Engr-in-Charge.

S&F Viterous China WHB table top Rectangular/Oval shape of size 650x450x150 mm with CP Waste coupling 32mm and PVC waste pipe 750mm long complete all as specified and directed by Engr-in-Charge.

S&F 1000 ltrs capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed by Engr-in-Charge.

S&F 20 mm bore PP-R , globe or gate valves, (brass insert) fixed.complete all as specified and directed by Engr-in-Charge.

S&F floor trap of PVC 75 mm out let dia with grating and jointed to waste pipe as spfd.complete all as specified and directed by Engr-in-Charge.

M&L for PVC (SWR) 110 mm gully trap setting joining with solvent cement complete all as specified and directed.

M&L for 75 mm thick PCC (1:3:6) type C2 using 40mm graded stone aggregate as in plinth protection finishing the surface even and smooth without using extra cement Complete all as specified and directed.

S&F 3 layer PP-R Polypropyene ransom copolymer outer dia of pipe 20 mm concealed pipes SDR 7.4 (PN-16) UV stabilzed and anti microbial fusionwelded having thermal stavility for hot & cold water supply including all PPR plain & brass threaded polypropylene random fittings fixed complete to wall s, ceilins or in floors etc.complete all as specified and directed by Engr-in-Charge.

S&F 3 layer PP-R Polypropyene ransom copolymer outer dia of pipe 25 mm concealed pipes SDR 7.4 (PN-16) UV stabilzed and anti microbial fusionwelded having thermal stavility for hot & cold water supply including all PPR plain & brass threaded polypropylene random fittings fixed complete to wall s, ceilins or in floors etc.complete all as specified and directed by Engr-in-Charge.

S&F 15 mm bore Angle cock, cast copper alloy, screwed down, high pressure, with capston head handle, screwed both ends for iron pipe and fixed.complete all as specified and directed by Engr-in-Charge.

S&F PVC connection 15mm size with PTMT nuts of length 450 fixed complete all as specified and directed.

S&F bib taps long body,15mm bore cast copper alloy with capston head handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed by Engr-in-Charge.

Supply and fix 15mm bore pillar taps swan neck CP brass chromium plated fancy type screwed down high pressure with chromium plated screwed shanks and fly nuts complete screwed for iron pipe/PPR complete all as specified and directed by Engr-in-Charge.

M&L plain cement concrete 1:3:6 Type C-2 (using 40mm graded crushed stone aggregate) as in bed to drain pipes including packing under and hunching against the sides of pipes after they are laid and tested for 150 mm bore SGSW pipe complete all as specified and directed by Engr-in-Charge.

S&F 75 mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joint laid in trenches or in floors complete all as specified and directed by Engr-in-Charge.

S&F 110 mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joint laid in trenches or in floors complete all as specified and directed by Engr-in-Charge.

S&F 150mm dia, PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed by Engr-in-Charge.

S&F Viterous China wash urinal, half stall type, white complete including providing and fixing plugs bedding urinal against wall in CM 1:2 securing urinal to plugs with and incl 60mm long brass screws, pointing around urinal back in cement incl 32mm dia PTMT waste coupling, 32mm dia PVC waste pipe and urinal spreader complete all as specified and directed by Engr-in-Charge.

S&F aluminium anodised powder coated windows / ventilator with side hung shutters / sliding shutters and frame made with aluminium section with and including glass/particle board 12mm thick (as specified below) Aluminium sections shall be of size as given below:- Frame : 44.5x44.5x1.60mm thickTop/bottom rail; 90x44.5mmx1.60mm thickside style/rails of shutter-44.5x44.5mmx1.60mm thick Glass : 5mm thick plain glass with rubber gasket with aluminium beading . Aluminium fitting such as peg stay, aluminium hinges, aluminium handle 100mm long, aluminium tower bolt 100mm long and making good of wall surface with matching to existing surface, complete all as specified and as directed by Engr-in-Charge.

M&L for readymade soft wood wall panelling & ceiling in strips of 100 mm width 10mm thickness having lounge and groove fixing arrangements fixed to wooden frame work(Size of frame work 1.2X1.2 C/C included ) as per manufacturers instruction including polishing complete all as specified and as directed by Engr-in- Charge .Note : if necassary size of the frame work/ wall paneling will be changed without any additional cost as per site requirement complete all as specified and as directed by Engr-in-Charge.

M&L Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and directed by Engr-in-Charge.

M&L for Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and as directed by Engr-in-Charge.

M&L Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr-in-Charge.

M&L for rolled mild steel as in trusses (framed), trussed, purlins, crane gantries, rails,Columns and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc fixed with base plate as specified and as directed by Engr-in-Charge.

S&F Anodised aluminium frame size 65x38 mm Powder coating for doors, windows, ventilators with one or more rebates including joining cleat for fixing to receive board etc. complete all as specified and as directed by Engr-in charge.

M&L Non asbestos fibre cement building boards 12 mm thick fixed or laid/ inserted to timber/GI/Aluminium framework with screws and fixed with jointless finish with jointing compound and jointing tape as per manufacturer instructions etc. complete all as spesifide and directed by Engr-in- charge.

S&F Anodised aluminium with powder coating door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and directed by Enger-in-charge.

S&F 150mm Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F thumb trun (both side) indicator lock complete all as specified and directed by Engr-in-charge.

S&F 250 mm Aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

M&L 75 mm thick cement concrete 1:4:8 type D-2 finished fair and even as in sub base Complete all as specified and directed.

M&L for 15 mm thick screed bed or bedding layer in CM 1:6 to receive floor finishes complete all as specified and directed.

M&L for chequred cement concrete tiles of size 300x300x25 mm thick coloured rubber pressed glossy finish, set and jointed in neat cement slurry and pointed in white or colour cement and match the surace of tiles as foor/staps, complete as all specified and directed.

Removing Excavated material exceeding 250 M but not exceeding 500M and depositing where directed at a level not exceeding 1.5 M above the starting point complete all as specified and directed.

M&L for providing cement concrete type B-1, 1:2:4 (20 mm graded aggregate) as in sides of interlocking paver blocks complete all as specified and directed.

Excavating over areas, n.exc 1.5 m deep and getting out in hard/dense soil complete all as specified and as directed by Engr -in-charge.

Excavating over areas, n.exc 1.5 m deep and getting out in hard/dense soil for each additional 1.5 m or part thereof in depth beyond the first 1.5 m complete all as specified and as directed by Engr -in-charge.

M&L for walling of random rubble stone masonry, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:4 complete all as specified and as directed by Engr -in-charge.

M&L for walling of random rubble stone masonry, uncoursed, well bonded, bedded and solidly hearted, laid dry complete all as specified and as directed by Engr -in-charge.

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; for rough finish and flat surfaces not exceeding 200mm thick (Horizontal or sloping) complete all as specified and as directed by Engr -in-charge.

M&L for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide, rough finished surfaces of concrete complete all as specified and as directed by Engr -in-charge.

M&L reinforced cement concrete (RCC) nominal Mix Type B1 1:2:4 (using 20mm graded crushed stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed by Engr -in-charge.

S&F cone cap cowl 80 mm dia, over vent pipe complete all as specified and as directed by Engr -in-charge.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, in hard/dense soil complete all as specified and directed by Engr-in-Charge.

S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5cm long complete all as specified and directed by Engr-in-Charge.

M&L for preparing new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified and directed by Engr-in-Charge.

M&L providing, cement concrete B1 1:2:4 (using 20 mm crushed stone aggregate as in coping complete all as specified and directed by Engr-in-Charge.

Rendering 15mm thick in CM 1:4 on PCC block masonry or concrete surfaces and finished even and smooth surface without using extra cement complete all as specified and directed by Engr-in-Charge.

M&L Cement concrete 100 mm thick typeC- 2, 1:3:6 (using 40mm graded crushed stone aggregate) in floor complete all as specified and directed by Engr-in-Charge.

M&L for Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed by Engr-in-Charge.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed. Note: Taking down carefully old FTL fitting recessed mounted light fittings/ceiling complete with all accessories and making necessary electric connection complete all as specified and directed by Engr-in-Charge.

M&L for 9mm Pre-laminated particle board, interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination fixed with screws/nails to timber frame work in wall portion complete all as specified and directed.

Providing & fixing false ceiling with semi perforated 8mm thick micro tegular edged GRG at all heights with GRG false ceiling tiles of size 595X 595 mm of approved texture design and patterns having moisture content less than 2% humidity resistance of 99% NRCO.50 to 0.75 as per IS 8225:1987,Noncombustible as per BS476(part4)-1970 and light reflectance of 85%(min) to be laid in true horizontal level suspended on inter locking metal T-grid of hot dipped galvanised iron sec of 0.33 mm thick (galvanised @ 120 grams per sqm incl both sides) comprising of main -T runners of size 15x 32 mm of length 3000mm ,cross-T of size 15X32 mm of length 600 mm to form grid module of size 600 x600 mm suspended from ceiling using galvanized mild steel items (galvanizing @80mm per sqm ) i'e 50mm long 8 mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1000mm length and L-shape level adjuster of size 85 x 25 x 2 mm ,Galvanised iron perimeter wall angle of size 24 x 24x 0.40 mm of length 3000 mm to be fixed on periphery wall/ partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall wood screws.The work shall be carried out as per specifications, drawing and as per directions of the Engr-in-Charge.

Dismantling of timber scantling in fillets, posts, rafters, purlins etc under 40Sq. Cm in section in framed work complete all as specified and directed.

M&L for 2nd class hard wood timber scantling plain fillets square, rectangular in section area exc 13 Sqcm and not exc 25sqcm secured with nails complete all as specified and directed.

M&L for 2nd class soft wood fillets sectional area exc 3 sqcm and n exc 6 sqcm rectangular or triangular in section but bullnosed, splayed, chamfered or rounded on one edge of face, secured with nails or brads, complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for coloured Non Skid Ceramic joint free tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm , in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed 15mm thick in CM 1:6 complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors & paving n.exc 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L Screed bed or bedding layer 20 mm thick in cement mortar 1:4 on floors for laying floor finish complete all as specified and as directed.

Taking down of chowkats with shutter (without taking of shutter from frame) exc 1.5 Sqm but not exc 4 sqm each complete all as specified and directed.

S&F 2nd class hard wood, Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

S&F plain 2nd class hardwood 35mm thich framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and as directed.

M&L for preparation of new or previously untreated wooden surfaces of any description not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint (1st grade quality) over a coat of pink primer complete all as specified and directed.

Taking down of chowkats with shutter (without taking of shutter from frame) n exc 1.5 Sqm each complete all as specified and directed.

S&F 30mm thick 2nd class hard wood glazed and skelton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a) completed all as specified and directed.

S&F 3mm thick sheet glass, ordinary quality and glazing with oil putty and glazing pins in square n exc 0.5 sq. m in each pane complete all as specified and directed.

S&F 100mm size, butt hinges, cold rolled steel or stainless steel with screw, medium weight , ISI marked complete all as specified and directed.

S&F 125mm long Aluminium, anodised, barrel tower bolt, Mild steel or stainless steel having dia/shoot not less than 10 mm with screws complete all as specified and directed.

S&F 125mm size, extruded aluminium alloy handles fabricated type anodised complete all as specified and directed.

S&F of 75mm size, butt hinges, cold rolled steel or stainless steel with screw, medium weight , ISI marked complete all as specified and directed.

S&F 100mm long Aluminium, anodised, barrel tower bolt, Mild steel or stainless steel having dia/shoot not less than 10 mm with screws complete all as specified and directed.

S&F 100 mm size, extruded aluminium alloy handles fabricated type anodised complete all as specified and directed.

Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and as directed.

M&L for 0.63mm thick CGI sheets fixed to wall/roof with two corrogations side lap, fixed with L- type or J type or cranked hook bolts and washers with grade of zinc coating 275 complete all as specified and directed.

M&L for 0.63mm thick CGI sheets fixed to wall/roof with two corrogations side lap, fixed with L- type or J type or cranked hook bolts and washers but except sheeting complete all as specified and directed.

M&L 0.63 mm thick plain galvanised mild steel sheeting, in ridges, hips, valley gutter, drip and straight flashings fixed with L- type or J type or cranked hook bolts and washers with grade of zinc coating 275 complete all as specified and directed.

M&L for two coat of synthetic enamel paint over a coat of red oxide on new steel surfaces of any description, not otherwise described over 10cm width or girth incl preparing new zinc or galvanised surfaces to receive painting by coating with mordant solution incl washing and cleaning etc completed all as specified and directed.

M&L for preparing old painted steel and iron surfaces of any description over 10 cm width or girth not otherwise described and applying two coat of synthetic enamel paint all as specified & directed by the Engr-in-Charge.

M&L for point wiring (Concealed type) complete with PVC insulated, sheathed stranded copper conductor (multistrand) of size 1.5 sqmm, 1100 volts grade conforming to IS 694/90, along with one single run of same size and type of copper wire as continuous earth wire to common earth dolly and supply and fixing rigid non metalic ISI marked PVC conduit pipe medium grade of size not less than 20 mm dia along with all accessories and fittings such as bends, tees, elbow etc, junction boxes including sunk terminal boxes, new 3 mm thick laminated sheet cover with brass screw and cup washers with all accessories and including cutting and chasing work on brick wall not exceeding 10 cm girth and making good to disturbed surfaces with cement mortar ratio 1:3 and treated surface with white/colour wash / OBD / Plastic paint to match with existing surface complete all as specified and directed for the following :- One light point or one fan point controlled by one way, single pole switch

Description all as per Srl item No. 106.00 here-in-before but for one socket outlet 3 pin, 5 Amps on same board.

Description all as per Srl item No. 106.00 here-in-before but for one socket outlet 15 Amps on independent board with 2.5 Sqmm copper conductor (Multi-stranded) insulated and unsheathed electric cable 1100 volts (ISI Marked) including PVC insulated and unsheathed electric cable 1100 volts 1.5 Sqmm copper stranded conductor as continuous earth wire connected to common dolly complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing switch piano flush button single pole one way 5 Amps complete as specified and as directed by Engr-in-charge.

Supply and fixing switch, socket combination 2 in 1, 5 Amp, flush type completeall as specified and as directed by Engr-in-charge.

Supply and fixing switch socket combination multi purpose 2 in 1, 3 pin 5A/16A, 5 in 1 flush type complete all as specified and as directed by Engr-in-charge.

Supply and fixing ceiling rose, surface bakelite, 65 x 50 mm, three terminals complete all specified and as directed by the Engineer-in-Charge.

Supply and fixing LED lights fitting 1x 20W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete as specified and as directed by Engr-in-charge.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size , complete all as specified and as directed by Engr-in-charge.

S&F LED street light luminaire of 35 Watt capacity, made of single piece pressure die-cast aluminium housing with high power LED with lens for proper light distribution luminiaries, IP 66, with toughned glass cover and incl control gear etc, with and incl making all electric connection, street light fitting bracket, 1.5 mtr long made out of galvanized iron pipe of 40 mm dia size light grade complete with and incl 02 nos MS clamp made of MS flate iron of 50 x 6 mm size with nut, bolts, washer etc with and incl two coats of aluminum paint over a coat of red oxide primer complete all as specified and directed by Engineer in charge.

S&F exhaust fan heavy duty 300 mm sweep, 1 Phase 1400 rpm including louvers and grounting with nut bolts complete all as specified and directed by Engr-in-charge.

S&F DB, double Door, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, SPN 8 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof, suitable for incorporation of MCB’s and isolators etc and making all necessary connections, duly flush of wall surface, complete all as specified and as directed by Engr-in-charge.

Supply and fixing MCB single pole and neutral 32 to 40 Amps , 240 volt, 10 KA, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing MCB single pole 6 to 32 Amps, 240 volts, 10 KA complete all as specified and as directed by the Engineer-in-Charge.

Supply and laying XLPE insulated, armoured, heavy duty electric cable, with stranded aluminum conductor 1100 V grade nominal cross sectional area 16 Sqmm, 2 core laid in trenches, ducts, drawn through pipes across the road/path/along poles/wall/floors/equipment etc including jointing and testing complete all as specified and directed by the Engr-in-Charge.

Excavation in trenches not exceeding 1.5m and not exceeding 1.5m in depth for laying of electric cable and getting out in hard and dense soil, complete all as specified and as directed by the Engr-in-Charge.

Material and labour for un-reinforced pre-cast concrete cable covers, class LV type-1, flat size 250mm x 150mm x 40mm thick complete all as specified and as directed by the Engr-in-Charge.

Material and labour for sand cushioning to under ground electric cable all as per clause No 19.75 of MES SSR Part-I (2009) complete all as specified and as directed by the Engr-in-Charge. Note: Only punned thickness shall be measured and paid.

Earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metres below normal ground level, connecting to the Galvanized iron earth wire 4.0 mm dia by means of bolts, nuts , check nuts and washers of galvanized iron and steel earth wire protected by provision of GI light grade pipe 15 mm bore including provision of concrete pit made from PCC ( 1:2:4) type B-1 (using 20 mm graded stone aggregate) with 40mm thick cover of RCC 1:2:4 reinforced with XPM (Weight not less than 4 Kg/Sqm) and frame of angle iron 40 x 40 x 6 mm and handle of 6 mm dia MS bar made to shape, GI light grade 20 mm bore pipe for watering perforated at bottom, 1.50 metre long placed on top edge of earth plate, common salt & charcoal filling, with fixing arrangement , funnel, wire mesh and earth work in hard/dense soil , returning filling in and removal of surplus soil to a distance not exceeding 50 metres, all as per electrical plate No 5 of SSR 2009 Part-I and connecting to CBDB’s as specified or indicated including testing on completion .

Taking down carefully copper/aluminum point wiring (light, fan, socket or power) complete with fittings and fixtures such as switches, ceiling roses, pendants, regulators, socket, lamp holders brackets, bulk head fittings, tube light fittings etc complete and removing all retrieved materials such as fitting & fixture from the site and also making good disturbed surfaces of wall, floors etc all as specified and as directed by the Engineer-in-Charge.

Material and labour for point wiring with 1.5 Sqmm copper conductor (Multi-standard) PVC insulated and unsheathed electric cable 1100 volts in and including PVC casing and capping of 25 mm and above (as per conductor run )with all fittings/ accessories and including PVC insulated and unsheathed electric cable 1100 volts1.5 Sqmm ( multi-stranded) copper conductor single core( Green colour) cable as continuous earth wire connected to common earth dolly including 50 mm deep box made of 2nd class hard board of required size and shape etc covered with 3 mm thick plastic laminated sheet ( Make Hylum) for one light point,bell,exhaust point, bulk head, independent controlled by one, one way switch complete all as specified and as directed by the Engineer-in-Charge.

Description all as per Srl item No. 126.00 here-in-before but for one 3 pin socket outlet 5 Amp on same board complete all as specified and as directed by the Engineer-in-Charge.

Description all as per Srl item No. 126.00 here-in-before but for one 3 pin socket outlet 5 Amp on independent board complete all as specified and as directed by the Engineer-in-Charge.

Description all as per Srl item No. 126.00 here-in-before but for one socket outlet 15 Amps on independent board with 2.5 Sqmm copper conductor (Multi-stranded) insulated and unsheathed electric cable 1100 volts (ISI Marked) including PVC insulated and unsheathed electric cable 1100 volts 1.5 Sqmm copper stranded conductor as continuous earth wire connected to common dolly complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in replacement socket outlet 2 in 1, 5 Amp, flush type completeall as spe cified and as directed by Engr-in-charge.

Supply and fixing in replacement angular lamp holder, PVC/Polycaronate type with back plate suitable for 12 watt LED bulb for batten fittings complete all as specified and directed by the Engineer-in-Charge.

Supplying and fixing in replacement LED 12 Watt complete all as specified and directed by Engr-in-Charge.

Supply and fixing new energy saving LED Bulk head fitting 10 watt made up of pressure die cast aluminium housing with acrylic cover as diffuser with IP 66 protection and impact resistance of IK07 as reqd to be mounting bracket in wall/floor to suit the opening of the fitting with FI clamp, nut, bolt and washers of suitable size including making connection complete all as specified and as directed by Eng-In-Charge

Supply and fixing in replacement LED luminaire 600 mm x 600 mm, 40 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling 6500K including connecting up with driver three core flexible copper conductor cable of suitable size complete all as specified and as directed by Eng-In-Charge.

M&L for sub main wiring with 2 run of 4 Sqmm FR, PVC insulated, unsheathed and stranded copper conductor cable with and incl 4 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable as earth wire connected with thimble from main DB to sub main DB, drawn drawn through & PVC casing and capping of 25 mm and above incl all conduit accessories & fittings / junction boxes / inspection covers etc, with and incl cutting chasing and making good of disturbed surface of wall / floor/ ceiling etc as original by brick work, plastering, white washing, OBD etc as required, complete all as directed. Note : 1. The cost of concealed conduit & accessories is deemed to be included in quoted rates. 2. The two run of 4 Sqmm wire and one run of 4 Sqmm wire will be measured as one unit.

Supplying & Laying, connecting and testing GI pipe 25 mm bore medium grade including necessary fittings in trenches complete all as specified and directed by Engineer-in-charge.

Supply and fix Gun Metal Gate Valve 25 mm dia with iron wheel head complete all as directed by Engineer - in-Charge.

M & L for Cutting and tapping in 25 mm water mains ( in position) for branch connections complete all as directed by Engineer - in-Charge.

M/s Koul & Sons (BID ID -3337739)

SHANTI ENTERPRISES (BID ID -3338207)

osho traders (BID ID -3333855)

M/S ASGAR ALI TIMBER SHOP (BID ID -3335832)