Construction of new Workshops block at Govt. ITI. Solan, Distt. Solan (HP).

Amount

Excavation in foundation, trenches etc. in earth work in all kind of soil lifts upto all heights and stacking the excavated soil in all specified distance. Clear from the edge of excavation and then returning the stacked soil in 15cm layers when required into plinths sides of foundation etc. consolidating each deposited layer by ramming & watering and then disposing of all the surplus excavated earth as directed within all leads and lifts disposed earth to be levelled neatly dressed.

Providing and laying cement concrete 1:4:8 (1cement:4sand:8graded stone agregate 40mm nominal size ) and curring complete excluding cost of form work in foundation and plinth.

Stone soling prperly handpacked filling interstices with kharnja stone & consolidated properly complete in all repsect.

Providing form work with steel plates 3.15mm thick weled with angle iron in frame 30x30x5mm so as to give a fair finish including levelling centering, shuttering strutting and propping etc. With wooden battens and ballies, hight of propping and cenring below supporting floor to ceiling in all heights and removal of the same for in-stu reinforced concrete and plain concrete work in:- a) Foundation, footing bases of colums etc. and mass concrete.

b) Columns, pillars, post and struts, square, rectangular or polygonal in plain.

c) Beams, cantilevers, girders & lintels, sides & soffits or beams, beam haunchings, cantilvers bressumers and lintels not exceeding 1mtrs in depth.

d) Flat surfaces such as soffits of suspended floors, roofs, landing of the like floors etc. upto 200mm in thickness.

e) Stair cases with slopping or stepped soffits excluding landing.

f) Vertical surfacessuch as walls.

Providing & laying reinfirced cement concrete work 1:1.5:3 (1cement: 1.5sand: 3 well graded stone aggregate 20mm nominal size) proportionally by weight with 43 grade cement @ 400 kg/cum minimum M-20 grade and curing complete excluding cost of form work and reinforcement for reinforced concrete work in all height as per HPPWD specifications with updated BIS norms. a) Foundation footing bases of columns etc. and mass concrete.

b) Columns, pilasrs, posts and struts, square, rectangular or polygonal in plain.

c) Suspending floors roofs landing & shelves and their supports, balconies, beams, girders, bressumers and cantilevers

d) Stair cases (except spiral staircases) excluding landing but prepairing of the surface and finishing of nosing upto all floor levels.

e) Walls (any thickness) attached pilasters, butresses, plinth and string courses etc. From top of foundation level upto all floor levels.

Providing tor steel reinforcement (Fe 415/ Fe-500 D as per design) for RCC work including bending, binding and placing in postion complete upto all floor levels.

Brick work using common clay burnt building bricks in superstructure above ground level in cement mortar 1:6 (1cement: 6 sand) 1st class bricks upto all height.

Half brick masonry in comman burnt clay building bricks in superstructure above plinth level upto floor two level with cement mortar 1:4(1cement:4 sand) 1st class bricks

Providing wood work in frames of doors, windows, clearstory and other frames, wrought, framed and fixed in position. Sal wood.

Prooviding 40 X 3mm flat iron hold fast 40cm. Long including fixing to frame with 10mm dia bolts, nuts and wooden splug and immeging in cement concrete block 10x10x15 cms. 1:3:6 (1cement: 3sand: 6graded stone aggregate 20mm nominal size).

Providing & fixing panelled glazed or panelled and glazed shutters for doors windows and clearstory windows including black enamelled iron butt hinges with necessary screws. 40mm thick 2nd. Class Deodar Wood.

Providing & fixing machine made flush door shutters for doors including black enamelled iron butt hinges with necessary screws. 40mm thick

P/F wire gauge shutters using galvanised M.S. Wire gauge of I.S. Gauge designation 85 G with wire of dia.0.56mm for doors,windows & clerestorey windows i/c bright finished black enamelled iron hinges with necessary screws.30mm thick 2nd class deodar wood.

Providing and fixing anodized aluminium sliding door bolt anodized transparent or dyed to required colour and shade with bolts and nuts screws etc. complete. (a) 300mm x 16mm.

Providing and fixing aluminium tower bolts (barrel type ) anodized transparent or dyed to required colour and shade with bolts and nuts screws etc. complete. a)200x10mm.

Providing and fixing aluminium handle anodized transparent or dyed to required colour and shade with nacessry screws etc. complete. (a)125mm.

Providing and fixing oxidized M.S. hooks and eyes 150mm

6mm cement plaster in ceiling with cement mortar 1:4(1cement:4 sand).

15mm cement plaster in single coat on the rough side of brick/concrete/stone walls for interior plastring upto all floor levels including arrrises, internal rounded angles, chamfers and/or rounded angle not exceeding 80mm in girth and finished evehn and smooth in cement mortar 1:6(1cement :6sand).

15mm cement plaster in single coat on the fair side of brick/concrete/stone walls for interior plastring upto all floor levels including arrrises, internal rounded angles, chamfers and/or rounded angle not exceeding 80mm in girth and finished evehn and smooth in cement mortar 1:6(1cement :6sand).

Providing and laying cement concrete 1:3:6 (1cement:3sand:6graded stone agregate 20mm nominal size ) and curring complete excluding cost of form work in foundation and plinth.

Kota stone slab flooring 20 mm ( average) thick base of cement mortar 1:4 (1 cement : 4 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete. 25mm thick

Kota stone slab 25 mm thick in risers of steps, skirting dado and pillars laid on 12 mm thick cement mortar 1:3 (1 cement : 3 sand) and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete. 25 mm thick

Providing and fixing 10mm thick anti skid water proof stain and impect resistent heavy duty vetrified tiles Nitco or equivalant 600x600mmx10mm manufactured of approved shade and colour in flooring, treads of steps and landings laid over 12mm thick cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete.

Providing and laying spartic ceremic tiles 5.5mm thick in flooring 300x300mm size on treads of steps laid on a bed of 12mm thick cement mortar 1:3(1cement:3sand) finished with flush pointing in white cement.

Digital Wall tiles 10mm thick in skirting risers of steps and dado 12mm thick cement mortar 1:3(1cement: 3sand) and jointed with cement slurry. (Premium quality).

Providing and laying heavy duty precast cement concrete inter locking paver blocks vibro compacted upto M- 30 grade i/c border or kurb block gray or coloured over sub-base of concrete with 25mm thick average thickness of cement mortar 1:4 (1cement:4sand) laid over and jointed with neat cement slurry mixed with pigment to match the shade of blocks i/c curring rubbing & polishing complete (sub base concrete floor to be paid for separately) bedding sand thickness 25mm as per MoRD specifications (clause- 1504) average 28 days strength of 8 blocks as 30 MPa & strenght of indivisual block not less than 26 Mpa (Clause 1504).

Providing & laying reinfirced cement concrete work 1:2:4 (1cement: 2sand: 4 well graded stone aggregate 20mm nominal size) proportionally by weight with 43 grade cement @ 320 kg/cum minimum M-15 grade and curing complete excluding cost of form work in all height as per HPPWD specifications with updated BIS norms in Foundation and plinth.

Providing and fixing glazing of powder coated aluminium in doors, windows, ventilators shutters and partitions etc. with PVC/neoprenes gasket etc. complete as per the architectural drawings and the directions of Engineer-in-Charge (cost of aluminium snap beading shall be paid in basic item).Glazing with glass panes of 5.50mm thickness and aluminium composite pannels. (weight not less than 13.75kg /sqm).

Providing and fixing M.S. grills of required patterns in woodan frames of windows etc. With M.S. flats, square bars with round headed bolts and nuts or by screws. Plain grill.

roviding and fixing in position collapsible steel shutters with vertical channels 20mmx10mmx2mm abd braced with flat iron diagonals 20mmx5xx size with top and bottom rails of T-iron 40mmx40mm stoppers, handles, including apllying a priming coat of red lead paint.

Supplying and fixing rolling shutters of approved make and made opf 80mmx1.25mm MS laths interlocking together through their entire length and joined together at the end by locks mounted on specially designed pipe shaft, with brackets side guides and arrangement for inside and outside locking with push pull operstion complete but excluding the cost of the top cover and spring shutters having width above 3.5 metres

Providing and fixing 27.50 centimeter long wire spring grade No.2 for rolliing shutter.

Providing and fixing ball bearing for rolling shutters

Providing and fixing top cover for rolling shutters shutters having width below 3.5 meters

Steel work welded in built, up saction in trusses and framed work including cutting hosting fixed in position & applying a priming coat of red lead paint in :- a) In grating framed guard, bars ladders, railing, brackets and similar works.

Providing and fixing 0.60mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia mter with prepainted limpet and rubber washers complete with all accessories as required as per the direction of Engineer-in-Charge.

Applying birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final metter finish to the surface complete.

Distempering (two coats) with oil boud washable disremper of approved brand and manufacture and of required shade on decorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and menufacture after thoroughly brushing the surface free from mortar dropping and other forign matter and also including preparing the surface even and sand papered smooth priming coat with distemper primer.

Finishing wall with Apex of Asian brand and manufacture and of required shade on undecorated wall surfaces (two coats) to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials.

Applying priming coat over new wood and wood based surface after and including prepairing the surface by thoroughly cleaning oil, dirt and other foreign matters sand papered & knotting. Ready mixed paint brushing wood primer pink.

Painting two coat (excluding priming coat) on new wood and wood based surfaces with readymixd paint brushing to give an even shade including cleaning of all dirt, dust and other foresign matter sand pepering and stopping with ready mixed paint. (a) White paint.

Applying priming coat over new steel and other matel surfaces after and including prepairing the surface by thoroughly cleaning oil grease, dirt and other foreign matters sand papered & knotting Ready mixed paint brushing red oxide/zink oxide chrome.

Painting two coat (excluding priming coat) on new steel and other metal surface under coat with ready mixed paint brushing to give an even shade including cleaning of all dirt, dust and other foreign matter with ready mixed paint other than white.

Providing and fixing on wall face PVC (D-plast) rain water pipes for working pressure not less than 4.5kg/sqm i/c filling the joits with the approved adhisives complete of Phinolex/ D-plast. (a) 150mm

P/f P.V.C. Fittings and accessories of Phinolex/ D-plast a) P/f PVC plain bend ISI marked including fixing with approved adhesives etc. Complete 150mm dia

Providing plinth protection under layer of 75mm thick bed of dry brick/stone aggregate 40mm nominal size well ramed and consolidated and ground with fine sand including prepration of ground finished with 50mm thick cement concrete 1:3:6 (1cement:3sand :6graded stone aggregate 20mm nominal size.)

Providing and applying two coat of Brawnflex Supertop over single coat of Brawnflex Prime as per site requirement and complete in all respect including all leads, lifts and carriage of material at site as directed by the Engineer In charge allowing drying gap between successive coats i/c Preparing the surface to receive waterproofing treatment by Removal of previous waterproofing treatment and making surface ready to receive water proofing treatment. Cleaning the surface with wire brushes to clean, smooth & dry surface, free of any loose particles/reinforcement bars/debris etc. Grooving and cleaning all the existing cracks and repairing them with polymer modified mortar. Washing if required before applying waterproofing coat.

Excavation in foundation, trenches etc. in earth work in all kind of soil lifts. Stacking the excavated soil not more than 3mtrs. Clear from the edge of excavation and then returning the stacked soil in 15cm layers when required into plinths sides of foundation etc. consolidating each deposited layers by ramming, watering and then disposing of all surplus excavated earth as directed within all leads and lifts disposed earth to be levelled neatly dressed.

Providing and laying cement concrete 1:4:8 (1cement:4sand:8graded stone agregate 40mm nominal size ) and curring complete excluding cost of form work in foundation and plinth.

Providing from work with steel plates 3.15mm thick weled with angle iron in frame 30x30x5mm so as to give a fair finish including levelling centering, shuttering strutting and propping etc. With wooden battens and ballies, hight of propping and cenring below supporting floor two ceiling and removal of the same for instu- reinforced concrete and plain concrete work in:- (a) Vertical surfacessuch as walls.

d) Flat surfaces such as soffits of suspended floors, roofs, landing of the like floors etc. upto 200mm in thickness.

Providing and laying cement concrete 1:3:6 (1cement:3sand:6graded stone agregate 40mm nominal size ) and curring complete excluding cost of form work in walls including attached buttresses, pilasters and their caps and bases string course etc. upto floor two level.

Providing & laying cement concrete work 1:1.5:3 (1cement: 1.5sand: 3graded stone aggregate 20mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in all height.(a) Walls (any thickness) attached pilasters, butresses, plinth and string courses etc. From top of foundation level upto all floor level.

(b ) Suspending floors roofs landing & shelves and their supports, balconies, beams, girders, bressumers and their cases (except spiral cantilever upto floor two level.

Providing tor steel reinforcement (Fe 415/ Fe-500 D as per design) for RCC work including bending, binding and placing in postion complete upto all floor levels. Tor steel.

Providing and fixing PVC pipe spigot and socket soils waste and ventilating pipes lead caulked joints to be measured and paid for separately . a)110mm

P/f P.V.C. Fittings and accessories . (a) P/f PVC plain bend ISI marked including fixing with approved adhesives etc. Complete 110mm dia

b) P/f PVC plain bend ISI marked including fixing with approved adhesives etc. Complete 75mm dia

a) P/f PVC Door bend ISI marked including fixing with approved adhesives etc. Complete 110mm dia

b) P/f PVC Door bend ISI marked including fixing with approved adhesives etc. Complete 75mm dia

a)P/f PVC Sinlge equal branch of required dergree ISI marked including fixing with approved adhesives etc. complete 110mm

b)P/f PVC Sinlge equal branch of required dergree ISI marked including fixing with approved adhesives etc. complete 75mm

a)P/f PVC Double equal branch of required dergree ISI marked including fixing with approved adhesives etc. complete 110mm

b)P/f PVCDouble equal branch of required dergree ISI marked including fixing with approved adhesives etc. complete 75mm

Providing and fixing PVC clamps ISI marked of approved design with steel screws and raw plugs etc. complete. a)150mm

Providing and laying in trenches the Galvanised mild steel tubes(medium grade), tube fittings (earth work in trenches to be measured and paid for seperate) 20mm nominal bore minimum weight 1.22 kg/rmt.

Providing and fixing to wall ceiling and floor G.I. pipe (Medium Grade) 15mm dia. With fittings and clamps i/c making good the wall, ceiling and floor

Making connection of galvanized mild steel distribution branch with galvanised mild steel main 20mm to 40mm nominal bore by providing and fixing tee including cutting and treading the pipe complete.

Providing & fixing pvc floor trap of self cleaning design with sand cast iron screwed down or hinged grating with or without vent arm complete i/c cost of cutting & making good the walls and floors. 110mm nominal dia.

P/F vitreous china wash down water closet (European type, W.C. Pan) with integral 'P'or 'S'trap including jointing the trap with soil pipe in cement mortar 1:1 (1 cement:1 Sand) Ordinary Type complete.

Providing and fixing 10.00 / 12.50/15.00 ltrs. capacity PVC low level flushing cistern with a pair of C.I or mild steel brackets complete with fitiings such as lead valve less syphon, 15mm nominal size brass ball valve with polyethene float, CP. Brass handle, unions & couplings for connection with inlet, outlet and overflow pipes, 40mm dia C.P. flush bend i/c cutting holes in walls and making good the same and connecting the flush bend with cistern and closet.

P/f plastic seat and cover for wash down water closet with CP brass hinges and rubber:- solid type white plastic seat cover

Providing and fixing water jet for water closet complete with all fittings such as Connection pipe.

Providing & fixing vitreous china wash basin with pair of hole for pillar tap with CI or MS brackets painted white including cutting holes and making good the same but excluding fittings flat back 630 x450mm of reputed make.Ovel Shape

P/L Granite Stone in flooring 20mm thick base in Cement Mortar 1:3 (1 Cement : 3 Sand) i/c jointing with grey cement slurry mixed with pigment to match the shade of pigment to match the shade of granite stone i/c rubbing and polishing complete 20mm thick.

Providing & fixng CP Brass waste for wash basin or sink 32mm dia.

Providing & fixng PVC waste pipe for wash basin or sink 32mm dia.

Providing & fixing 100mm sand cast iron grating for gully, floor or Nahni trap.

Providing & fixing 750 x 900mm bevelled edge mirror of superior glass mounted on 6mm thick AC sheets or plywood sheet and with teak wood corners and fixed to wooden plugs with CP brass screws and washers.

Providing and fixing C.P. brass towel rail complete with C.P. brass bracket fixed to wooden plugs with C.P. brass screws. 600mm x 20mm.

Providing & fixing CP brass Pillar tap with capastan head 15mm dia. (having weight not less than 400 grms).

Providing & fixing CP brass bib tap with capastan head 15mm dia.(having weight not less than 400 grms).

P/F C.P. brass soap dish with C.P. brass brackets fixed to wooden cleats with C.P. brass screws.

P/F C.P. brass angle valve 15mm without Nuts and pipe.

P/F brass stop cocks: (a) 15mm dia

(b) 20mm dia

Providing & fixing PVC connection pipes with brass unions 45cm lenght 15mm nominal bore.

Providing and fixing G.I. or M.I. unions. 15mm dia.

Providing and fixing white glazed fireclay stall urinal with automatic C.I. Flushing cistern (of approved make) with fittings R.S. Or C.I. Brackets standart size C.P. Brass flush pipe spreaders with unions and clamps (all in C.P. Brass) C.I. Trap with outlet grating and other coupling in C.P. brass including painting of cistern and fittings, cutting and making good the walls and floors where required: Single Stall urinals with 5 litres C.I. automatic flushing cistern.

Providing and fixing Division Plate for urinals 600mm x 300. Vitreous China

Providing and fixing PVC water storage tank G.I. Inlet and outlet connection, 15mm nominal bore ball valve and mosquito proof PVC cover with locking arrangement i/c hoisting upto all heights above ground level: 1000 ltrs. net Capacity tank.

Providing & fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked i/c fixing with approved adhesive etc. Complete.i)150 mm dia.

Constructing manhole with RCC top slab in 1:2:4 (1cement: 2sand: 4graded stone aggregate 20mm nominal size) foundation concrete 1:4:8 (1cement: 4sand: 8graded stone aggregate 40mm nominal size) inside plastering 15mm thick with cement mortar 1:3 (1cement: 3sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1cement: 2sand: 4graded stone aggregate 20mm nominal size) finished smooth complete including curing complete and testing. Inside size 800 x 800mm and 500mm deep including RCC cover and frame medium duty 500mm internal dia with 200mm thick walls of brick masonary using common burnt clay building bricks in cement mortar 1:3 (1cement: 3sand) complete.

Providing and fixing PVC cowl. 100mm nominal size

SITE DEVELOPMENT Cutting in earth work and disposal of excavated earth upto all lead and all lifts in all kind of soils.

Excavation in foundation, trenches etc. in earth work in all kind of soil lifts. Stacking the excavated soil not more than 3mtrs. Clear from the edge of excavation and then returning the stacked soil in 15cm layers when required into plinths sides of foundation etc. consolidating each deposited layers by ramming, watering and then disposing of all surplus excavated earth as directed within all leads and lifts disposed earth to be levelled neatly dressed.

Providing and laying cement concrete 1:6:12 (1cement:6sand:12graded stone agregate 40mm nominal size ) and curring complete excluding cost of form work in foundation and plinth.

Providing form work with steel plates 3.15 mm thick welded with angle iron in frame 30x30x5mm so as to give a fair finish including centring, shuttering strutting and propping etc. with wooden battens and ballies, height of propping and cenetering below support floor to ceiling in all height and removal of the same for in-situ reinforce concrete work and plain concrete work in :- (a)Vertical surfaces such as walls (any thickness) partitions and the like i/c attached pilasters buttresses, plinth and string courses and the like.

Providing and laying cement concrete 1:3:6 (1cement:3sand:6graded stone agregate 40mm nominal size ) and curring complete excluding cost of form work in walls including attached buttresses, pilasters and their caps and bases string course etc. upto floor two level.

Providing and Fixing weep Hole with 90mm thick PVC pipe

Stone filling behind retaining wall.

VK Mangla