ADDN ALTN AND SPECIAL REPAIR OF 04 BLOCKS (48 QTRS) OF OR MD ACCN AT 180 OR MAHIPALPUR UNDER GE (SOUTH), DELHI CANTT-10

Amount

Roughening surfaces of old concrete floor/wall by picking, sweeping clean and washing down with water to remove dust, etc and brushing and applying neat cement slurry with 3.0 Kg of cement per sq metre, complete all as specified and directed.

M&L for light shade ceramic tiles 10 mm thick (square/rectangular) polished, area of each tile not exceeding 0.36 sqm, as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specified and directed.

M&L for light shade ceramic tiles 10 mm thick (square/rectangular) polished, area of each tile not exceeding 0.36 sqm, as in skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed.

M&L for non-skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specified and directed.

M&L for joint free glazed ceramic coloured tiles in vertical surface 450x300x7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match, complete all as specified and directed.

M&L for screed bed or bedding layer of mortar 15 mm thick for laying floor finishes in CM 1:6, complete all as specified and directed .

M&L for backing coat/ plaster 10 mm thick on fair faces of brick work in CM 1:4 surfaces to receive tiles, complete all as specified and directed .

Dismantling stone slabs and tiles of any discription or thickness in floors, aprons etc, laid bedded and pointed in any mortar, complete all as specified and directed.

M&L for granite (of any type) work, 20 mm thk (table rubbed and polished) in steps,jambs,pillars, window-cills, cooking platforms and like in 20mm thick screed bed cement screed bed 1:6 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, complete all as specified and directed .

M&L for machine cut mirror finish polished kota stone slab flooring 18-20mm thick over 20mm thick cement screed bed laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing, complete all as specified and directed.

M&L for kota stone slab 18-20mm thick in riser of steps, skirting, dado and pillar, laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing, complete all as specified and directed.

Demolition of brick work built in cement mortar or cement lime mortar, complete all as specified and directed.

M&L brick work with sub class `B' bricks straight or curved on plan exc. 6mtr mean radius built in cement mortor 1:6, complete all as specified and directed.

M&L brick work with sub class 'B' bricks strainght or curved on plan to any radius in half thick in CM 1:4 brick wall built in cement mortor, complete all as specified and directed.

Taking up or down steel tubing and connections including cleaning for re-fixing, 15 mm bore of pipe, complete all as specified and directed .

All as per Srl item No 16 here-in-before but 20 mm bore of pipe

S&F 20mm bore UPVC pipe SDR 11 & plain CPVC SCH-40 fittings on walls/ceiling or laying in floors including all fittings such as (brass elbow, brass Tee, made threaded brass adaptor, female threaded adaptor etc) union, ball valves, flange adn tank adaptor complete all as specified and directed.

All as per Srl item No 18 here-in-before but 25 mm bore pipe

Cutting chases or making holes, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth, complete all as specified and directed .

Dismantling water tanks of capacity exceeding 250 litres but not exceeding 500 litres, complete all as specified and directed .

S&F 500 ltr capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position, complete all as specified and directed .

S&F ball brass valves, high pressure, with of PTMT with epoxy coated aluminium rod & high desity plastic ball ascrewed for iron pipe of 20mm bore and fixed, complete all as specified and directed .

S&F in repairs gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe 20 mm bore, complete all as specified and directed.

S&F PVC connections 450mm long with brass unions at both ends suitable for 15mm bore pipe, complete all as specified and directed.

S&F in repair 15 mm angle valve/ stop valves, cast copper alloy , chromium palted, fancy type screwed down high pressure with crutch and butter fly handles , screwed with iron pipes or for union, complete all as specified and directed.

S&F in repairs bib tap (quarter turn), brass chromium plated fancy type, long body with flange screwed down, screwed for iron pipe 15 mm bore, complete all as specified and directed.

S&F in repairs pillar tap, brass chromium plated fancy type with capstan heads, screwed down high pressure, screwed for iron pipe 15 mm bore, complete all as specified and directed

S&F in repairs chromium plated grating with 100mm dia of approved make includingh fixing with CM 1:4 to floor/ nahni trap etc., complete all as specified and directed

S&F in repairs grating doom 125mm dia with waste hole of PTMT (minimum weight 40 gms) etc., complete all as specified and directed

S&F in repairs brass chromium plated overhead shower rose 125mm dia, with revolving joint and shower rod to fixed to 15mm bore pipe, complete all as specified and directed

S&F brass chromium plated tubular towel rail, 20mm dia, 'D' type 60cm long between flanges of brass CP, complete all as specified and directed

S&F in repair stainless steel sinks without drainage board made of stainless steel 01mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm, complete all as specified and directed

S&F brass chromium plated health faucet alongwith 1.00 to 1.50 meter good quality SS flexible connection pipe suitable for 15mm bore pipe, complete all as specified and directed

S&F in repair vitreous china wash down water closet pan (pedestal pattern) , white fixed in repair,including sheet cover of closed pattern with flat bottom and mild steel chromium plated or aluminiumised hinging device, complete all as specified and directed

S&F in repair, PVC valveless , syphonic action type flushing cisterns 10 ltrs capacity , low level , white, with inlet ball valves , float and handle including brackets and pvc flush pipe 32 mm dia for low level, complete all as specified and directed

S&F in repair vitreous china wash basin, white, angle back, size 400 x 400mm, including necessary waste pipe and coupling, brackets and cutting for and pinning in ends of brackets, complete all as specified and directed

S&F 6mm thick glass corner shelf fancy type with railing and fittings complete of size 25cm x 25cm of best quality (as per sample approved by Engr-in-charge), complete all as specified and directed

S&F brass chromium plated soap dish 150mmx150mm, of any type, fixed to plugs with chromium plated brass screws, complete all as specified and directed

Taking down chowkats with shutters not exceeding 1.5 Sqm each (without taking off shutters from the frames), complete all as specified and directed

All as per Srl item No - 41 here-in-before but exceeding 1.50 sqm and not exc. 4.00 sqm each

Taking down shutter of any descreption exc. 1.00 sqm but not exc. 2.00 sqm each, complete all as specified and directed

S&F pressed steel frames of size 125mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, complete all as specified and directed

S&F factory made solid PVC chowkhat/ door frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet and edges will be painted to match with printed PVC sheet reinforced with 19mm x 19mm MS square tube of 19 gauge including rubber gasket, PVC fastners, screws, brackets, and shown on drawing as per SSR part-II (2020), complete all as specified and directed

S&F factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick wood grain printed moulded prelam PVC sheet on the front face & 2mm thick plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing, complete all as specified and directed

S&F 35 mm thick Factory made IInd class hardwood plain,framed paneled shutters (any numbe of panels) with lock rail and panel of 9mm BWP commercial ply with commercial veneering on both faces size of rail and stile as per IS-1003 (part) Kiln seasoned and chemically pressure treated, complete all as specified and directed

S&F 35 mm thick factory made IInd class hard wood glazed and Skelton shutters (three panels) open rebated and prepared to receive glass/ gauge etc. divided into squares edges of framing plain, chamfered or rounded mitered and rebated sash bar any number with cut or mitered beads for securing glass/ gauge etc. size of members of shutters, complete all as specified and directed

S&F stainless steel butt hinges, size 100 mm complete, complete all as specified and directed

S&F stainless steel barrel tower bolts, 150 mm long, complete all as specified and directed

S&F stainless steel handles, 150 mm long, complete all as specified and directed

S&F stainless steel sliding door bolts 250mm long with hasp, staple (bolt type) fixing clips of sheet cast, fixing bolts, complete all as specified and directed

M&L for preparation of new wooden surfaces of any description not otherwise described over 10 cms width or girth and apply two coat of synthetic enamel paint over a coat of pink primer, complete all as specified and directed

M&L for preparation of old wooden surfaces of any description not otherwise described over 10 cms width or girth and apply one coat of synthetic enamel paint, complete all as specified and directed

M&L for preparation of new steel surfaces of any description not otherwise described over 10 cms width or girth and apply two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed

M&L for preparation of old steel surfaces of any description not otherwise described over 10 cms width or girth and apply one coat of synthetic enamel paint, complete all as specified and directed

S&F in repair stainless steel wire cloth, 0.63mm nominal dia or wire and sqm average width or aperature 1.40mm, fixed with tinned tacks or galvanised wire staples to doors/steel windows, complete all as specified and directed

S&F stainless steel wire cloth, 0.63mm nominal dia or wire and sqm average width or aperture 1.40mm, fixed with tinned tacks or galvanized wire staples to doors/steel windows, complete all as specified and directed.

S&F in repair stainless steel barrel tower bolts, 150 mm long, complete all as specified and directed

S&F in repair stainless steel handles, 150 mm long, complete all as specified and directed

S&F in repair stainless steel sliding door bolts 250mm long with hasp, staple (bolt type) fixing clips of sheet cast, fixing bolts, complete all as specified and directed

M&L powder coated aluminium anodised three way track sliding windows of frame size 92 mm x 31.75 mm x 1.5mm thickness (section no. 20831 of JINDAL) and of shutter size 40 mm x 18 (with 9.00 mm interlocking legs) x 1.45 mm thick (section no. 20737 of JINDAL) section (two shutter glazed, covering half of span of opening each & one shutter sketlon covering half of span of opening ) incl provn for making windows air tight, including 95mm aluminium handle with spring lock , stainless steel wire cloth, 0.45 mm nominal dia of wire and average width of aperature 1.4mm and fixed with steel wire stapples 5mm thick plain glass including necessary fitting/ fixture/ aluminium snap beads, complete all as specified and directed . (Note:- Measurement shall be taken clear opening ie out to out of window frame as a whole including all fittings and fixtures and no extra shall be paid separately).

S&F fabricated aluminum window with powder coated anodized aluminum frame of section 63.5mm x 38.10mm x1.5mm thick, shutter with section 47.62mm x 44.45mm x 1.5mm thick including aluminum anodized “D “ handle, hinges, peg stays, tower bolts, etc including jointing cleats for fixing builder's hardware fittings & stainless steel wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples including necessary fittings/fixture /aluminum snap beads, complete all as specified and directed

Dismantling boarding, any description, fixed in any position with nails, complete all as specified and directed

M&L for 18mm thick wood plastic composites (WPC) board, fixed with screws as in cupboard/ wardrobe/ almirah shutter including all necessary fittings and fixtures like nickle plated clip hinges, knobs etc complete all as specified and directed. Note: (a) Pattern & design of WPC board to be decided by GE. (b) Items like cupboard knobs, and CP plate clip hinges deemed to be included in the quoted rate.

S&F in repair drapery curtain rods, stainless steel 25 mm dia of approved quality with decorative wooden finish and two number brackets fixed in brick/concrete wall and same finished knobs on each end of curtain rod including 8 Nos (min) match up rings etc., complete all as specified and directed

Dismantling wrought iron or mild steel/ cast iron work of any description, complete all as specified and directed

M&L for mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/ or riveted, welded or forged into spikes, framed guard bars, window frames, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work fixed in position including holdfasts or screws confirming to Fe.290.Gde-E-165, complete all as specified and directed

M&L for welding in repairs exc 2.5 cm but not exc. 5.0 cm in length thickness of metal be welded exc 6mm but n.exc 9mm, complete all as specified and directed

S&F MS stainless steel peg set of five fixing with wall, complete all as specified and directed

S&F in repair kitchen plate rack with four shelves made out of stainless steel sheet 1 mm thick overall size 750mm x 750mm x 250mm, complete all as specified and directed

Taking down cement or cement lime plaster, any description, on brick or stone walls, concrete surface etc including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed

M&L for 15mm thick rendering with ready mix plaster on faces of brick or concrete surface, finished even and smooth without using extra cement, complete all as specified and directed

M&L for 10mm thick rendering with ready mix plaster on concrete surfaces of ceiling, chajja,etc finished even and smooth, complete all as specified and directed

M&L for preparation of newly plastered surfaces of wall and applying 1 to 2 mm thick wall care putty on whole surfaces to achieve smooth, even and uniform surface including grinding with sand paper and levelling of surface and applying two coat of oil bound distemper on white or tinted over existing prepared putty base surface, complete all as specified and directed

M&L for preparation of newly plasered surfaces of walls and applying two coat of cement based paint over a coat of alkali resistant primer, complete all as specified and directed

M&L for preparation of newly plasered surfaces of ceiling and applying 1 to 2mm thick wall care putty on whole surface to achieve smooth, even and uniform surface including grinding with sand paper and levelling of surface and applying two coats of oil bound distemper on white or tinted over existing preparation putty base surface complete all as specified and directed

M&L for complete removal of existing treatment from internal surfaces of wall by electrically operated grinder, washing and filling of holes with filler material and applying 1 to 2 mm thick wall care putty in two layers on whole wall surface including grinding with sand paper and levelling the surface and then applying two coat of oil bound distemper on white or tinted surface over existing prepared putty based surface, complete all as specified and directed

M&L for preparation of old surfaces of wall and applying two coats of white wash, complete all as specified and directed

M&L for preparation of old surface of ceiling and applying one coats of white wash, complete all as specified and directed

Cutting of vegetable plant (girth not exceeding 300mm) from roof, terrace, chajjas etc digging out the roots and making good the surface in PCC 1:2:4 type B1 with surfaces finished to match including scaffolding etc, complete all as specified and directed

Dismantling of brick tiles (laid flat or on edge) on roof surface.laid bedded and pointed in any mortar, complete all as specified and directed

Demolition of mud in roof, any thickness, including plastering and leeping upto two storey bldg including necessary scaffolding arrangement complete (whether full thickness removed or only a part there of) and removing rubbish from cantonment area or as directed, complete all as specified and directed

M&L for cutting out craks to V-section in existing roof or terracing, cleaning out, wetting, grouting with cement and sand slurry 1:3, complete all as specified and directed

M&L for roof treatment in following stages, complete all as specified and directed. (i) Preparation of concrete surfaces by wire brush and cleaned top surfaces of cement concrete . (ii) PCC type B-0, 1:2:4 (12.5mm gradded aggregate) to maintain slop with average thick of 40mm as in roof. (iii) Applying evenly a tack coat of industrial bitumen 85/25 @ 1.2 Kg per sqm including cleaning surfaces (iv) APP polymeric water proofing membrane minimum 3 mm thick and wieghing not less than 3.0 Kg per Sqm , black finish reinforced with non woven polyester matt with a thermo fasable finish laid over bitumen primer @ 0.5Kg/Sqm by torching application with a propane or a butrane gas torch with an overlap of 100mm at the sides and 150mm at the ends, as per manufacturers instructiions.

M&L for cement concrete tiles 20cm x 20cm x 20mm thick, machine pressed, set jointed and pointed in neat cement slurry in floors, and cut and polished laid over 15mm thick screed bed in CM 1:6, complete all as specified and directed

M&L for cement concrete type B1 - 1:2:4 (using 20mm graded stone aggregate) in roof kerbs or mud stop rounded or chamfered on edge etc., complete all as specified and directed

Dismantling of cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required, complete all as specified and directed

S&F 110 mm dia UPVC pipes Type 'B', single socketed, in any length with rubber ring joints, laid in trenches or in floors or fixed to walls complete all as specified and directed

S&F 75 mm dia UPVC pipes Type 'B', single socketed, in any length with rubber ring joints, laid in trenches or in floors or fixed to walls complete all as specified and directed

S&F 75mm UPVC (SWR) bends/tee/branch piece type ‘B’ (any radius), complete all as specified and directed

S&F 110mm UPVC (SWR) bends/tee/branch piece type ‘B’ (any radius), complete all as specified and directed

S&F in repair UPVC floor/ nahani trap including jointing with solvent cement, dia of outlet 75mm, complete all as specified and directed

S&F in repairs 125mm x 100mm salt glazed stone ware gully traps square & round mouthered trap 'P' including case iron grating and fixed, including necessary excavation and earthwork, concrete in bed, surrounds, kerbs etc., and jointing to drains in CM 1:1, complete all as specified and directed

Taking down rain water pipe (any size) or pattern incl all fittings, head shoes, bends swan necks etc incl cleaning or re-fixing or removal to store(measured overall as fixed along the centre line over fittings and accessories, complete all as specified and directed

S&F 110 mm UPVC pipes Type 'A', single socketed, in any length with rubber ring joints, laid in trenches or in floor or fixed to walls, complete all as specified and directed

S&F 110mm UPVC (SWR) Bends/Tee type ‘A’ (any radius), complete all as specified and directed

S&F holder bat clamps 100mm bore out of 50mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof, complete all as specified and directed

All as per Srl item No - 99 here-in-before but 75mm bore

Demolition of cement concrete (un reinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level), complete all as specified and directed

M&L for cement concrete 1:3:6 type C2 (using 40mm graded stone aggregate) in plinth protection, 75 mm thick, finished even and smooth without using extra cement, including making joints 12mm wide to the full depth of PCC at every 3 metres and at every change of direction and filling the same with & including bitumen and sand 1:3 by weight, complete all as specified and directed

M&L for 75mm thick PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base, complete all as specified and directed

M&L for 60mm thickness machine pressed pre-cast concrete interlocking paver block any size and shape confirming to IS 15658-2006, M-30 grade with grey cement and no pigment, laid over 40mm thick sand cushion and including joints filled with sand, complete all as specified and directed.

M&L for chipping of spelled and loose concrete and cleaning rust from reinforcement by sand blasting, scrubbing down concrete surfaces with wire brushes cleaning with water allowed to dry applying a layer of zinc rich epoxy primer as anti rust on all exposed reinforcement followed by a layer of bonding coat of a layer of epoxy adhesive on complete exposed surfaces of concrete and provide gunniting in two layers over steel welded mesh 2 mm dia of wire and total aperture 75 mm, thickness of gunite n.exc 25 mm thick (average thickness) using cement mortar 1 :2 with OPC 43 grade cement mixed with polycrete admixture @ 2 % by weight of cement or as per manufactures instructions and finally applying cement plaster over gunite surfaces of required thickness to give an even uniform and smooth finish conforming to proper geometrics in cement mortar 1:4 to match with the existing surface as in side and soffits of slabs, chajjas, fins, facias, parapets, columns and beams etc complete including necessary scaffolding , shuttering necessary chased to brick work or RCC members at any height upto full height of buildings including removing of small trees shrubs etc complete all as specified and directed. (Note: Steel mesh to be welded with the existing reinforcement. The cost of welded mesh is deemed to be included in the unit rate quoted.)

M&L for udaipur green marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade including 20mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for providing and injecting chemical chlorpyrifos emulsifiable for post constructional anti termite treatment along the external wall below concrete or masonary apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes, complete all as specified and directed

M&L for anti termite treatment of soil under existing floors using chemical chlorpyrifog emulsifiable concentrate @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar (1:2) to match the existing floors, complete all as specified and directed

M&L for 15mm thick rendering with ready mix plaster on brick or concrete surfaces finished even and smooth without using extra cement mixed with by adding permeability reducing polymer @ 250gm/sqm (6%) by weight of cementitious content at time of mixing with water as per manufacturer's recommendations including all levelling the surface, curing etc complete. (Note :- Water proofing compound shall be measured & paid separately).

M&L for providing and applying a bond coat of Latex: Water : cement - 1:4:6 with latex consumption @100gm/sqm on the brick wall surface by brush as per manufacturer's recommendations including curing, complete all as specified & directed.

Expose the first joint of masonry structure at ground level horizontally. The plaster must be knocked off at least 50 cm beyond the visibly penetrated area. Damaged mortar joints are to be scraped out to a depth of approximately 2-3 cm. Drilling Holes: Drilling holes 10mm diameter in masonary structure along the side of the joint at 45° angle so as to cross the brick/block at the intervals spacing if 15-30cm depending on extent of rising dampness as per recommendation of engineer in charge. Cleaning of holes: Clean the holes by air blower prior to fixing nozzles. Install Packer injection packers 9.8mm diameter, 10cm long in the holes and tighten. Fix the packer securely using Sikadur 31. Note: Cutting of Packers: Cut the packers after completion of grouting without damaging structural elements.

Supply and apply of a 3 part, very low viscous, elastic polyacrylic injection resin Injection 306 with a versatile and adjustable reaction time having Mixed viscosity : 3-11 M.pa.s at +20 Deg C, Reaction time : adjustable according to ambient temperatrure and execution requirement between 8-50 mins, pH – 9-10, Tested as per Wissbau No. 2002-094-(1A) – Function test with re-injectible hose system. The holes should be drilled until a depth of approx 5 cm (for a 6cm thick wall) before the end of the wall is reached. Pump Injection-306 at >20 bar into or behind fissures or into masonry joint which are allowing water to infiltrate into unwanted areas. If voids in masonry being injected contain insufficient moisture to activate the grout inject a small amount of water prior to injecting the grout. When movement stops or Injection-306 appears at the next packer move to the next packer and inject. If the dampness is heavy, inject similarly at next joint line, complete all as specified & directed.

M&L rendering 15mm thick on fair faces of brick work or concrete surface in CM 1:6 on wall surfaces and finished surface even and smooth without using extra cement complete all as specified and directed

M&L rendering 10mm thick on ceiling in CM 1:3 finished even and fair without using extra cement complete all as specified and directed

Description of Work / Item(s)

Amount

Taking down carefully the old U/S Aluminium / Copper point wiring (light, fan, socket or power) complete fitting such as switches, ceiling roses, pendants, sockets, regulators, etc and making good disturbed surfaces of walls including necessary touch up with the adjoining surface of disturbed area ie with OBD/colour wash/white wash as the existing finish complete all as specified and directed.

M&L for point wiring complete, stranded copper conductor 1.5 Sqmm nominal area PVC insulated FRLS 1100 volts grade electrical cable in but with through concealed PVC conduit and including replacement of unserviceable pressed steel terminal boxes of required size wtih modular steel terminal boxes including white cover modular plate with frame suitable for modular switches, modular sockets, modular fan regulators etc including 1.5 sqmm stranded copper conductor PVC unsheathed cable earth wire to common earth and connected to earth dolly complete all as specified for One light/Fan/bell point controlled by one switch 5 Amps one way using cable (1.5 Sq mm for phase and neutral and 1.5 sqmm for earthing) and making good to disturbed surface of walls including necessary touch up with through adjoining surface of disturbed area i.e with OBD/colour work/white wash as existing finishes complete all as specified and directed Note :- The rate is inclusive cutting/chasing and making good disturbed surface with CM 1:3 and same surface finishs with the adjoining surface of disturbed area with OBD/Colour wash/white wash complete.

All as per item No 2 above but One 3 pin socket outlet, 5/6 Amps, independent

All as per item No 2 above but 5 Amp socket outlet on same board

All as Item No 2 above but for one socket outlet 5/15 Amps on Independent board with cables 2.5 sqmm size for phase and neutral and 2.5 Sqmm for earthing

All as Item No. 2 above but for one light point controlled by two 2-way switches with cable 1.5 Sqmm size.

S & F switch modular type 5/6 Amps SP one way complete all as specified and directed

S & F switch modular type 1M 5/6 Amps SP 2 way complete all as specified and directed

S & F socket outlet 2-in-1, 5/6 Amps modular type 2M 5 pin multi purpose complete all as specified and directed

S & F switch modular type 1M 15/16 Amps SP one way complete all as specified and directed

S & F universal socket outlet 2-in-1 (multipurpose) 5pin 6/16 Amps modular type 2M complete all as specified and directed

S & F bell push, modular type 5/6 Amps complete all as specified and directed

S & F ceiling rose surface Bakelite 65x25 mm two to three terminals complete all as specified and directed

S&F in replacement of old unsv wall light fixture any type of LF-1/Sketch light fitting with Decorative wall light fixture made up of Polycarbonate, suitable for 10/12 Watt LED of 6.5K and connected with flexible cable 2 core copper conductor 0.50Sqmm complete all as specified and directed

S&F in replacement Surface mounting round shaped LED downlighter with durable housing with Al heat shrink with diffuser to give glare free light 6 Watt LED lamp type in replacement of old unsv existing light fitting any type from ceiling of stairs/common areas, complete all as specified and directed

S&F in replacement Wall mounted LED Integrated Batten T5 20 Watt - 4Ft White, indoor decorative PVC extruded T5 LED battern-Integrated type in replacement of old unsv existing any wattage fittings any type, complete all as specified and directed

S&F in replacement Wall mounted LED Integrated Batten T5 10 Watt-2 Ft White, indoor decorative PVC extruded T5 LED battern -integrated type. in replacement of old unsv existing any wattage fittings any type, complete all as specified and directed

S&F in replacement LED lamp 12 Watt LED Bulb complete all as specified and directed.

S&F in replacement 10 LED bulk head in engineering plastic housing with clear prismatic diffuser, 10W WHITE in replacement of old unsv bulk head/Sketch/LF fitting including all accessories connecting up twin core flexible copper conductor cable complete all as specified and directed

S&F in replacement of building security light fitting 45W LED 5000K new Powder coated pressure die cast aluminium compact LED Street light including pole for fixing as reqd of bracket duly fixed with clamps, nut, bolts & washers etc complete all as specified and directed

S&F of electric bell Ding Dong type AC, 230 volts single phase complete all as specified and directed

S & F 0-4 step type electronic fan regulators modualr type 120W 2M for ceiling fan 1200mm sweep, 240V complete all as specified and directed

28. S&F BLDC (Brushless Direct Current) Ceiling Fan 1200 mm Sweep,not less than 350 RPMhaving air delivery 215Cum, high air flow with silence operation, with fully copper winded motor & ribbed 3 Nos A/M blades. The BLDC motor fan shall have 100% rust free blades. The fan shall be BEE 5 Star rating and compliant with IS 374 and making necessary electric connection of suitable PVC copper wire from ceiling rose to ceiling fan complete all as specified and directed by Engr in charge including taking down old ceiling fan and depositing to MES store yard complete all as specified and directed (Make :- Orient -Model Hector/Havells-Model Efficiencia Neo/Bajaj-Model Energos28

S&F in replacement of VTPN DB 6 way double door, vertical type for fixing MCCB up to 200 Amps as incommer and MCBs as out goings with metel door and IP 43 Protections and connecting of approved make by the GE complete all as specified and directed.

S&F in replacement of sheet metal enclosures double door for DBs when MCBs to be used SPN-8 Way, 240V with 200 Amp rated busbar complete as per site requirement complete all as specified and directed

S&F in replacement of MCCB 4 Pole .415 V. fixed type, 160 Amps with breaking capacity 36kA complete all as specified and directed

S&F in replacement MCB SPN 32 Amps 'C' series, breaking capacity 10 Ka, 'C' curve 240 volts, 50 Hz including necessary incoming and out going electric connection with suitable size of copper lugs etc complete all as specified and directed

S&F for MCB SP 6 to 32 Amps 240 Volts, 10kA, `C' curve all as per site requirement complete all as specified and directed

S&F for MCB SP 40 Amps 240 Volts, 10kA, `C' curve all as per site requirement complete all as specified and directed

M&L for earthing with galvanized steel earth plate electrode 60 cm x 60 cm x 6mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.5 M below normal ground level connected to GI wire 4 mm as earthing lead by means of nut, bolts and check nuts and washers, GI light grade protection pipe 15 mm dia upto 7.5 M, GI watering pipe 20 mm dia medium grade, RCC cover with funnel, excavation in any type of soil, PCC pit charcoal, salt all as shown in electrical plate No 5 of SSR Part I, including earth test point upto panel board, all as specified or indicated including testing on completion complete all as specified and directed.

Taking down and re-fixing single phase static energy meter in meter box in and including its connection complete and mounting on existing wall surface including necessary connections of incoming and out going cables complete all as specified and directed

S&F in replacement Sheet metal enclosure of size 300 x 250 x 150 mm suitable for mounting Single phase electric meter fabricated from 2mm thick CRCA sheet with anti corrosive dust and vermin proof. Note:- The meter cover shall have a fully transparent window. The window shall be of transparent, high grade UV stabilized engineering plastic for easy reading of all the displayed values/parameters and observation of operation indicator. The window shall preferably be an integral part of meter cover complete all as specified and directed

Taking down unserviceable Submain wiring twin core of any size complete and making good disturbed surface complete all as specified and directed.

M&L for Sub Main wiring using single run PVC FRLS grade Insulated unsheathed, multistrand copper conductor cable 2 runs of 6 Sqmm for phase and neutral and 1 run of 6 Sqmm for earth wire drawn through concealed PVC conduit wiring in wall not less than 25mm dia with all fittings like tees, bends, junction/ terminal boxes etc as per site requirement and all as directed. (Note:- Phase should be of Red /Yellow/Blue, neutral should be of back and earthing wire should be of green colour. 2 runs of cable for phase/ neutral and 1 run for earth will be measured and paid as one unit length).

Taking down exhaust fan of any sweep and refixing after the same including its connection and mounting on exisitng wall surface including necessary electric wire connection etc complete all as specified and directed

Taking down geyser and refixing after the same including its connection and mounting on exisitng wall surface including necessary pipe, electric wire etc complete all as specified and directed

S&F earth leakage circuit breaker 16A, 30 mA 1P+N C16 ELCB with two way sheet metal enclosure distribution board for geyser complete all as specified and directed

A R construction

M/s VINOD KUMAR SHARMA

L G BUILDERS

JYOTI ENTERPRISES

V M CONSTRUCTION

Shivom Projects Private limited

M/S Chhavi Constructions Co

CHOPRA BUILDERS

JYOTI ENTERPRISES

V M CONSTRUCTION

A R construction

HIND CONSTRUCTIONS

Shivom Projects Private limited

CHOPRA BUILDERS

L G BUILDERS

M/S Chhavi Constructions Co

Bidder Name

V M CONSTRUCTION

L G BUILDERS

A R construction

M/s VINOD KUMAR SHARMA

Shivom Projects Private limited

M/S Chhavi Constructions Co

HIND CONSTRUCTIONS

CHOPRA BUILDERS

JYOTI ENTERPRISES