CERTAIN B/R PETTY WORKS AT BHARATHIYAAR NAGAR CVRDE AVADI

Amount

M&L for Securing glass of any description in existing in metal frames glazed with putty/ beads & glazing pins/spring clips including removing loose or decayed putty/beads, painting/oiling one coat on rebates, grooves, reputtying and painting/oiling puttied surface to match existing work (New length of frame reputtied shall be measured) complete all as specified and as directed by Engineer in Charge.

Taking down cement plastering of any description scrubbing down with water washing down etc. complete all as specified and as directed by Engineer in Charge.

M&L for Rendering 10 mm thick on fair faces of brick work or concrete wall surfaces in CM 1:6 finished even and smooth without using extra cement complete all as specified and as directed by Engineer in Charge.

M&L for preparation of new plastered surfaces and applying two coat of distemper over a coat of primer on walls all as specified and as directed by Engineer in charge.

Dismantling floor/wall tiling including cement mortar bedding (including backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed by Engineer in Charge.

Demolition of cement concrete (un reinforced ) in ground floors and pavings not exceeding 15 cm thickness(below or above ground level),complete all as specified and as directed by Engineer in Charge.

M&L for PCC 1:2:4 Type B0 (using 12.5 mm graded stone aggregate), as in floor of 25 mm thick complete all as specified and as directed by Engineer in Charge.

M&L for Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1: 6 complete all as specified and as directed by Engineer in Charge.

M&L for Glazed ceramic coloured tiles in vertical surface 350x450x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick plaster in CM 1:4 complete all as specified and as directed by Engineer in Charge.

M&L for Non-skid joint free matt finish ceramic coloured tiles (of approved quality) 10 mm thick size of each tiles not less than 605mmx605mm/ 600mmx600mm in floors, set and jointed in neat cement slurry and pointed in coloured cement to match, laid over and including 15mm thick screed bed layer in cement mortar 1:6 complete all as specified and as directed by Engineer in Charge.

M&L for Non-skid joint free matt finish ceramic coloured tiles (of approved quality) 10 mm thick size of each tiles not less than 605mmx605mm/ 600mmx600mm in skirting, set and jointed in neat cement slurry and pointed in coloured cement to match, laid over and including 10mm thick backing coat in CM 1: 4 complete all as specified and dricted

M&L for 20mm thick granite (of any type) black coloured slab in single piece for platform of kitchen/WHB, machine cut bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match over 15mm thick screed bed in CM1:4 the shade of granite stone including grinding and polishing complete all as specified and as directed by Engineer in Charge.

S&F vitreous china squating pan "ORISSA' pattern or size 550 x 440mm white with integeral foot rest etc (Excluding flushing cistern and f;lush pipe) complete including trap set in cement mortar & provision of lime concrete bedding and making good to floor, fixed in repairs complete all as specified and as directed by Engineer in Charge.

Demolition of lime concrete (un reinforced) of any description in any position complete all as specified and as directed by Engineer in Charge.

Applying evently a tack coat of industrial bitumen grade 85/25 at the rate of 1.2 kg sqm incl cleaning surfaces complete all as specified and as directed by Engineer in Charge.

M&L for Lime concrete with brick aggregate in lime mortar 1:3 as in filling of sunken slabs, complete all as specified and as directed by Engineer in Charge.

M&L for PCC 1:2:4 type Bo using 12.5 mm graded stone aggtegate 40mm average thickeness finished even and smooth w/o using extra cement complete all as specified and as directed by Engineer in Charge.

M&L for 15mm thick rendering in cement mortar 1:3 on concrete / brick surface finished even and smooth without using extra cement mixed with WPC (WPC shall be measured and paid separately) complete all as specified and as directed by Engineer in Charge.

Supply only integral water proofing compound

S&F in repair Tubular towel rail 20mm dia D type 60cm long between flanges brass chromium plated complete all as specified and as directed by Engineer in Charge.

S & F in repair for bib tap cast copper with capsten head, chromium plated, screwed down high pressure, with or without lettered ,Hot or Cold with long screwed with crutch or butterfly handle, fancy type ,screwed down, screwed for 15mm dia iron pipe complete all as specified and as directed by Engineer in Charge.

S&F in repair angular stop cock cast copper alloy with capasten head, chromium plated, screwed down high pressure, with or without lettered ,Hot or Cold with long screwed with crutch or butterfly handle, fancy type ,screwed down, screwed for 15mm dia iron pipe and all complete all as specified and as directed by Engineer in Charge.

S&F in repairs Pillar taps, cast copper alloy with capstan heads,chromium platted screwed down high pressure with or without lettered HOT or cold with long screwed snates and fly nuts, Screwed for iron pipe and fixed for 15mm bore dia(Fancy type) complete all as specified and as directed.

S&F in repairs CP brass shower rose 125mm size and 15mm dia, fixed in repairs complete all as specified and as directed by Engineer in Charge.

S&F in repairs Stainless steel sink with draining board, made out of 1.00mm thick sheet for kitchen or laboratory with plug, washers waste pipe, cast iron cantilever brackets or bedding in cement motar on to dwarf wall, connecting union overall size 915mmx460mm with bowl size 410mm x 330mm x 160mm complete all as specified and as directed by Engineer in Charge.

S&F in repairs PVC valveless, syphonic action type, flushing cistern, 10 ltrs and flush pipe syphonic action type, low level, white, with inlet, ball valve, float and handle including brackets of approved including taking down flushing cistern of any model complete all as specified and as directed by Engineer in Charge.

S&F vitreous china wash basin, flat back, size 550 x 400mm excluding taps ,waste pipe, including cutting for and pinning in ends of brackets or erecting stand and including bracket fixed in repair complete all as specified and as directed by Engineer in Charge.

S&F vitreous china wash down water closet (pedestal pattern) white including connecting to trap and to flushing pipe anti syphonage pipe etc seat cover complete set in concrete flush pipe to closet including all joints and making good floor and wall complete all as specified and as directed by Engineer in Charge.

S&F in repairs Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and as directed.

S&F in repairs PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and as directed .

S&F in repair Ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed in repair in 20mm dia pipe (Minimum weight 2 0 m m - 2 1 0 g m s) complete all as specified and as directed by Engineer in Charge.

S&F in repair CP Brass Waste coupling fitting 32mm dia suitable for WHB including rubber washer complete all as specified and as directed by Engineer-in-Charge

S&F in repair CP Brass Waste coupling fitting 40mm dia suitable for stainless steel sink including rubber washer complete all as specified and as directed

Taking down or up old 15 mm steel tubing galvanised and connections including cleaning for refixing of serviceable tube all as specified and as directed by Engineer-in- Charge .

Taking down or up old 20 mm steel tubing galvanised and connections including cleaning for refixing of serviceable tube all as specified and as directed by Engineer-in- Charge .

Refixing old steel tubing and connections in new or old position (walls, ceiling, flooring etc) of 15 mm Bore of pipe all as specified and as directed by Engineer-in- Charge .

Refixing old steel tubing and connections in new or old position (walls, ceiling, flooring etc) of 20 mm Bore of pipe all as specified and as directed by Engineer-in- Charge .

Supply and fixing tubes medium grade galvanised with all fittings fixed complete to walls and ceiling or laid in floors of 15mm bore pipe all as specified and as directed by Engineer-in- Charge .

Supply and fixing tubes medium grade galvanised with all fittings fixed complete to walls and ceiling or laid in floors of 20mm bore pipe all as specified and as directed by Engineer-in- Charge .

Taking down of Shutters of any description exc 1 sq. m and n exc 2 sq. m complete all as specified and as directed by Engineer in Charge.

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site including 03 Nos 75mm SS hinges,02 Nos 150mm Aluminium handle and 02 Nos 150mm tower bolt in each shutter complete all as specified and as directed by Engineer in Charge.

S&F for Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per pecification & drawing complete all as specified and as directed by Engineer in Charge.

Cutting windows/ventilators from its position and Welding with box type hinges including replacement of damaged member and making good the surface by painting with synthetic enamel paint including primer all as directed by Engr-in-charge

Taking down existing steel windows/ventilators without taking of shutters (gauzed and glazed)from the frame of area n.exc 2 sqm each complete all as specified and as directed by Engineer in Charge.

S & F 4mm thick Figured glass pin head type and glazing with rubber gasket in squares n.exc 0.50 sqmm in each pane complete all as specified and as directed by Engineer in Charge.

S&F Aluminium powder coated louvers movable type in pairs for ventilators including locking arrangement complete all as specified and as directed by Engineer in Charge.

S&F Aluminium powder coated frame made out of hallow extruded section (minimum thickness of powder coating 50 micron) for window/ventilators with one or more rebates including joining cleats, beads for fixing etc complete all as specified and as directed by Engineer in Charge.

S&F stainless steel kitchen plate rack size 24"X24"X10" all as specified.

Hacking out old broken glasses any thickness size , quality, description from metal frame including punching or drilling out old glazing pins /spring clips etc complete all as specified and as directed by Engineer in Charge.

S & F 3 mm thick sheet glass ordinary quality and glazing with oil putty and cilips in squares n. exc 0.5 sqm each pane complete all as specified and as directed by Engineer in Charge.

S&F Stainless steel wire cloth 0.63mm nominal dia of wire and average width of apreture 1.40mm and fixed with stainless steel wire staple in aluminium ventilators incl necessary aluminium fittings complete all as specified and as directed by Engineer in Charge.

S&F in repairs 300mm long aluminium anoised sliding door bolt with hasp staple (Bolt type) and fixing clips of sheet cast or extruded section and fixing both and sliding boths of external section or cast alumnium aloy and flexed complete all as specified and as directed by Engineer in Charge.

S&F in repairs 200mm Aluminium anodized barrel tower bolts of extruded section and fixed complete all as specified and as directed by Engineer in Charge.

S&F in repairs Aluminium handle cast type anodized of size 150mm long complete all as specified and as directed.

S&F in repairs MS 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete including welding to steel chowkat complete all as specified and as directed.

S&f in repair Hasp and staple 75mm , safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and as directed.

S&F in repairs door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring and having high quality rubber pad complete all as specified and directed by Engineer-in-Charge

S&F in repairs stainless steel wire cloth 0.63 mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples complete all as specified and as directed by Engineer in Charge.

S&F in repairs chromium plated Health faucet ABS SS Braided hose 1m with CP hook , and fixed for 15mm bore dia(Fancy type). complete all as specified and as directed by Engineer in Charge.

S&F in repair 30 mm dia MS curtain rod (Drapery) pre-painted, all as specified as directed by Engr In-Charge.

S&F in repair fancy type curtain bracket accessories for 30 mm dia drapery rod, complete all as specified as directed.

ANISHRAJAN ENTERPRISES

GURU ENTERPRISES

k.Pandurangan