E-TENDER FOR REFURBISHMENT OF SHOOTING RANGE BUILDINGS 25 METER, 50 METER, FINAL RANGE and 10 METER

Litre

Excavation for foundation in hard murum including removing the excavated material upto a distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift from 1.5 to 3.0m) By Manual Means Spec. No.:- Bd.A.1 Page No.259

Removing brick bat coba including stacking the spoils as directed with all leads, lifts etc, complete. Spec. No.:- As directed by Engineer in charge.

Removing doors and windows with frames and stacking the materials as directed with all leads, lifts etc. complete. Spec. No.:- As directed by Engineer in charge.

Dismantling brick masonry in lime or cement mortar and stacking the materils as directed with all leads, lifts etc. Spec. No.:- As directed by Engineer in charge.

Removing cement tiles, or marble or polished shahabad floor or dado without bed concrete including stacking the materials as directed with all leads, lifts etc. complete Spec. No.:- As directed by Engineer in charge.

Removing urinal pans or wash hand basins with frame including disconnecting the sanitary and water supply connections, removing the same carefully and stacking the serviceable materials as and where directed including throwing the unserviceable materials outside etc complete Spec. No.:- As directed by Engineer in charge.

Removing W.C. pans including disconnecting the sanitary and water supply connections, removing and breaking flooring and bed con-crete around pan removing the same carefully and stacking the serviceable materials as adn where directed including throwing the unserviceable materiasls out side etc. carefully and throwing out the refusal outside etc. complete. Spec. No.:- As directed by Engineer in charge.

Providing preconstructional antitermite treatment as per I.S. 6313 (Part-I) to the soil along the external face of building by punching holes of 1.2 of 1.5 C.M. diametre about 30 -60 cm deep at 15 cm c/c as close to the wall as possible and to inject 0.5 percent of aldrin or clorophyrifos at the rate of 7.5 litres per hole and sealing the same with proper filling and covering 10 years guarantee on bond paper. Spec. No.:- As directed by Engineer in charge.

Transportation of excavated & debris from site to disposing site inluding loading , unloading & tranportation etc. complete. (lead 3km)

Providing Autoclaved Aerated Concrete Block masonary of conforming to IS:2185 (Part 3) - 1984 in extra fine jointing mortar of fixoblock of UltraTech or equivalent in superstructure including striking joints, raking out joints and scaffolding etc. Complete. (The test shall be carried out conforming to IS:6441 (Part I) - 1972) Spec. No.:- As directed by engineer in charge

Providing internal cement plaster 6 mm thick in a single coat in cement mortar 1:3 without neeru finish to concrete surface in all positions including scaffolding and curing etc. complete. Spec. No.:- Bd.L.1 Page Number 367

Providing internal cement plaster 12mm thick in single coat in cement mortar 1:4 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etc. complete. Spec. No.:- Bd. L.2 Page Number 368

Providing neeru finish to plastered surfaces in all positions including scaffolding and curing etc. complete. Spec. No.:- Bd. L.10, Page Number370

Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 mm thick in cement mortar 1:4 using waterproofing compound at 1Kilogramper cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete. Spec. No.:- Bd.L.7 Page Number 369

Providing and laying vitrified mirror / glossy finish tiles decorative type having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10 mm thickness and confirming to IS. 15622- 2006 ( group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and clearing etc. complete. a) Flooring Spec.No.:- Bd.M. 12 Page No.385

Providing and laying vitrified mirror / glossy finish tiles having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 ( group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and clearing etc. complete.b) Skirting /dado, Spec.No.:- Bd.M. 12 Page No.385

Providing and laying vitrified matt fininsh tiles having size 590 mm to 605 mm x to 605 mm of 8 to 10 mm thickness and confirming IS. 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement morar including neat cement float, filling joints, curing and cleaning etc. complete. a) Flooring Spec.No.:- Bd.M.12 Page No. 385

Providing and laying vitrified matt finish tiles having size 590 mm to 605 mm x to 605 mm of 8 to 10 mm thickness and confirming IS. 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and cleaning etc. complete. b) Skirting /dado, Spec.No.:- Bd.M.12 Page No. 385

Providing and laying in position flooring of telephone black / Amba White / Cat bary brown / Ruby red / Ocean Brown granite stone of approved shade and size 18 mm to 20 mm thick on bed 1:6 cement mortar including cement floats striking joints, pointing in C.M. 1:3 curing and cleaning etc. complete. Spec.No.:- Bd.M. 3 B/Page No. 380

Providing and laying telephone black / Amba White / Cadburybrown / Ruby red / Ocean Brown granite stone of 18 to 20 mm thick for door frame/ dado/ window boxing etc. On C.M. 1:6 including filling joints with polymer base filler nosing the sharp edges wherever necessary, curing, etc. complete. Spec.No.:- As directed by Engineer-In- Charge

Providing and fixing machine cut machine polished 18 mm to 20 mm thick telephone black / Amba White / Cat bary brown / RBI red / Ocean Brown granite stone for treads and risers of steps and staircases of approved colour and shade with rounded moulding and three grooved line for the treads on bed of 1:4 Cement mortar including float filling joints with neat cement slurry curing polishing and cleaning etc. complete. Spec.No.:- Bd. M.22 B/Page No. 390

Providing and fixing machine cut mirror polished 18 mm to 20 mm thick telephone black granite / Amba White / Cat bary brown / RBI red / Ocean Brown granite stone partition with full moulding the edges etc. complete . Both side polish Spec. No.:- Bd.M.35 B/Page Number393

Providing cement based water proofing treatment to terraces (Indian water proofing or alike) with brick bats laid in required slope to drain the water for any span after cleaning the base surface. Applying a coat of cement slurry admixed with approved water proofing compound and laying the brick bats on bottom layer in C.M.1:5 admixed with approved water proofing compound filling up to half depth of brick bats, curing this layer for 3 days, applying cement slurry over this layer joints of brick bats with C.M.1:3 admixed with approved water proofing compound and finally top finishing with average 20 mm. thick layers of same mortar added with jute fiber at 1 Kg per bag including finishing the surface smooth with cement slurry admixed with approved water proofing compound. Marking finished surface with false squares of 300mm x 300 mm. making the junctions at the parapet rounded and tapered top for required height, with drip mould at the junction of plaster and parapet and curing and covering 10 years Guarantee against leakproofness on Court fee stamp paper of Rs. 500/- including ponding test etc. complete. Spec.No.:- As directed by Engineer in charge. a) Second floor & terrace

Providing water proofing in W.C. and bath including brick bat coba in all position including providing and laying 12 mm bedding in cement mortor 1:3 on vergin concrete slab with water proofing compound @1 kg/per bag of cement laying brick bat coba of required thickness in cm 1:5 with water proofing compound 1 kg/bag of cement grouting and finishing the top layer with 20 mm thick brick bedding in cm mortor 1:3 with water proofing compound 1 kg/per bag of cement and testing the treated portion for 48 hours by pond test and covering ten years' guarantee on requisite stamp paper including curing etc. complete . Spec. No.: As directed by Engineer-in-charge

Providing waterproof plaster in W.C. and bath 12 mm thick for dado in cement mortar 1:3 with neat finishing, floating using waterproofing compound at the rate of 1 Kilogram. per bag of cement of approved make and manufacturer and curing etc. complete. (Excluding Tiles) (As directed by Engineer in Charge) Spec. No.:- As directed by Engineer in charge.

Solid Core Flush door Single leaf Providing and fixing factory made solid core flush door in single leaf 35 mm thick, decorative types, of exterior grade, as per detailed drawings, conforming to I.S.:2202 - 1962 (Revised) with approved face Laminet WP on both faces with/without glazing and venetians in the positions shown on the drawings or as directed, all necessary beads, moulding and lipping, holdfasts, mat finish stainless steel fixtures fastenings , finishing with french-polish/ waxing complete. (without door frame).(Sample to be got approved from Ex.Engineer before use) Commercial Hard Wood shutter Spec. No.:- As directed by Engineer-in-charge

Solid Core Flush door Double leaf Providing and fixing factory made solid core flush door shutters in double leaves 35mm thick,decorative type of exterior grade, as per detailed drawings, conforming to I.S.: 2202 1966 (Revised) including approved face laminet WP on both sides, without glazing and venetians including mat finish stainless steel fixtures and fastening, stoppers and finishing with french polishing etc. (Excluding door frame)(Sample to be got approved from Ex. Engineer before use) Commercial Hard Wood shutter Spec. No.:- As directed by Engineer-in-charge

Providing and fixing M.S. grill door 24 Kilogram/Square Metre of various size as per detailed drawings without hot dip coating, iron fixtures and fastenings and 3 coats of oil painting etc Spec. No.:- As directed by Engineer in charge.

Providing and fixing in position (as per 1868 / 1982) Aluminium sliding window of three tracks with rectangular pipe 95 x 38.10 x 0.90 mm at weight 0.637 Kilogram/Running metre. with window frame bottom track section 92 x 31.75 x 1.30 mm at weight 1.070 Kilogram/Running metre.. Top and side track section 92 x 31.75 x 1.30 mm at weight 0.933 Kilogram/Running metre. The shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight 0.417 Kilogram/Running metre. Inter locking section 40 x 18 x 1.10 mm at weight 0.469 Kilogram/Running metre. and handle and top section 40 x 18 x 1.25 mm at weight o.417 Kilogram/Running metre. As per detailed drawings and as directed by Engineerincharge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mm thick plain glass and aluminium mosquito net shutter with stainless steel jail with all required screws and nuts etc, complete. With powder coating with box Spec. No.:- As directed by Engineer in charge.

Providing and fixing in position powder coated aluminium louvered windows / ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80 x 38 mm x 1.22 mm box type, 5 mm thick sheet glass louvers, of approved quality etc. complete. Spec. No.:- As directed by Engineer in charge.

Providing and fixing false ceiling of 12mm thick as per drawings including powder coated G.I. wall angle of 20mm x 20mm size, G.I. grid runners of size 20mm x 38mm at 600mm center to center both ways and suspended using G.I. 3mm wire including fixing using butterfly clips and fasteners including transporting, scaffolding all necessary labour and machinery, finishing etc. complete. Spec. No.:- Bd. R. 19 Page Number 462

Providing and Fixing of GI Lay in Plain metal ceiling consisting of 600x600mm Lay in tiles of pre coated galvanized steel in 0.5 mm thickness in Global white color tile to be laid on grid systeM.S. Hostel A with 15mm wide T - section flanges color white having rotary stitching on the Main Runner, 1200 mm and 600 mm Cross Tees.Providing and Fixing of GI Lay in Plain metal ceiling consisting of 600x600mm Lay in tiles of pre coated galvanized steel in 0.5 mm thickness in Global white color tile to be laid on grid systeM.S. Hostel A with 15mm wide T - section flanges color white having rotary stitching on the Main Runner, 1200 mm and 600 mm Cross Tees.products approved as per GRIHA and BS 476 etc. complete. Spec. No.:- As directed by Engineer in charge.

Providing and applying two coat of pearl/ luster finish paint of approved colour and shade to the existing plaster surface including scaffolding, preparing the surface, applying the acrylic wall putti etc. complete. Spec. No.:- As directed by Engineer in charge.

Providing and applying priming coat on concrete/ masonar

y/ Asbestos Cement plastered surfaces including scaffolding if necessary, preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and sand papering as required etc. complete. Spec. No.:- As directed by Engineer in charge.

Providing and applying two coats of exterior acraylic emulsion paint confirming to corresponding I.S. of approved manufacture and of approved colour to the plastered surfaces including cleaning ,preparing the plaster surface, applying primer coat ,scaffolding if necessary , and watering the surface for two days etc complete. Spec. No.:- As directed by Engineer in charge.

Providing and fixing mild steel grill work for windows, ventilators, etc. 15 Kilogram/Square Metre as per drawing including fixtures necessary welding and painting with one coat of anticorrosive paint and two coats of oil painting complete. Spec. No.:- Bd.U.1 Page Number 537

Providing and fixing white european type wall-hung, of size 360mm x 360mm x 575mm with flush valve of approved make including soil pipe, vent pipe upto outside face of wall, 100mm dia C.I. plug bend inlet pipe all fittings,cutting & making good walls, floors etc as directed by Engineer in charge. Spec. No.:- As directed by Engineer in charge

Providing and fixing white glazed earthenware Wash Hand Basin of 55cm. x 40 cm. size including cold water pillar tap/cold and hot water pillar tap brackets, rubber plugs and brass chain, stop tap and necessary pipe connections including P.V.C. waste pipe and trap up to the outside face of the wall. Making good the damaged surface, testing etc. complete. Spec. No.:- Bd.V.30 Page Number 565

providing and fixing oval type under counter wash hand basin of 16 inch x 22 inch size and of special colour shade having telephonic black / coloured granite of 180 mm thick stone black kadappa framework including chromium plated coupling bottle - Trap using CERA company or equivalent oval typa wash basin model no 3448 as per detailed drawing or as directed by engg incharge etc complete. (Counter size 1.20 m x 0.60 m ) Spec. No.:- As directed by Engineer in charge

Providing and fixing 450mm x 550mm size superior type Belgium mirror with 16mm dia. nickel plated towel rod etc. complete. Spec. No.:- As directed by Engineer in charge.

Providing and fixing C.P.Two way BIB cock of approved make continental including necessary sockets/union nut etc. complete. Spec. No.:- As directed by Engineer in charge

Providing and fixing Hand shower (health faucet) with 8mm dia. 1m long flexible tube having wall hook with approved make including necessary sockets/ union nut etc. complete as directed by Engineer in charge. Spec. No.:- As directed by Engineer in charge

Providing and constructing granite kitchen platform with fixing of stainless steel sink 600 mm x 450 mm size as per detailed drawing including vertical both side polished kadappah stone 25 to 30 mm thick supports with kadappah top 35 to 40 mm thick and polished granite 16 to 20 mm top with side strips of granite at front and both sides of platform raised with two vertical granite supports 15 cm height and top granite of 75 x 40 cm including cutting, opening for sink of required size in kadappah as well as granite etc. complete. (Platform top size __ m x 0.60 m and height is 0.75 m) Spec. No.:- As directed by Engineer in charge.

Providing and fixing stainless steel sink of size 600 x 510 x 200 mm incluidng coupling, outlet pipe, elbow and other necessary fitting, finishing etc. complete. Spec. No.:- As directed by Engineer in charge

Providing and fixing C.P. sink cock with raised J" shaped swinging casted spout of approved make including necessary sockets/ union nut etc. complete." Spec. No.:- As directed by Engineer in charge

Providing and fixing 10cm C.I. Nahani Trap including C.I. grating bend and piece of C.I. pipe upto the outside face of the wall complete. Spec. No.:- Bd.V.32 Page Number567

Providing and fixing on walls/ ceiling/ floor 15 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. Spec. No.:- BD.V 5 page 551 and as directed by Engineer in charge

Providing and fixing on walls/ceiling/floor 20 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. Spec. No.:- BD.V 5 page 551 and as directed by Engineer in charge

Providing and fixing on walls/ ceiling/ floor 25 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. Spec. No.:- BD.V 5 page 551 and as directed by Engineer in charge

Providing and fixing on walls/ ceiling/ floor 32 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. Spec. No.:- BD.V 5 page 551 and as directed by Engineer in charge

Providing and fixing on walls /ceiling/ floor 40 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. Spec. No.:- BD.V 5 page 551 and as directed by Engineer in charge

Providing and fixing on walls/ ceiling/ floors, 25 mm dia. heavy grade having embossed as ISI Mark galvanised iron pipes weight of 3.01 Kilogram/meter with necessary fittings . remaking good the demolished portion and applying primer of anti-corrosive oil paint 2 coats Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. Spec. No.:- Bd.V.5 Page Number 551

Providing and fixing on walls/ ceiling/ floors, 32 mm dia. heavy grade having embossed as ISI Mark galvanised iron pipes weight of 3.89 Kilogram/meter with necessary fittings . remaking good the demolished portion and applying primer of anti-corrosive oil paint 2 coats Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. Spec. No.:- Bd.V.5 Page Number 551

Providing and fixing 75 mm dia stabiliser pipe/ P.V.C. / soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete Spec. No.:- As directed by Engineer in charge.

Providing and fixing 100 mm dia stabiliser pipe/ P.V.C./ soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete. Spec.No.:- As directed by Engineer in charge.

Providing and fixing P.V.C. Rain water pipes of 110mm outer diameter and having wall thickness of 2.2 to 2.7 mm confirming to I.S. 13592-1992 including proper rainwater receiving recess with P.V.C. plug, bend, necessary fittings, such as, offsets, shoes, inluding fixing the pipe on wall using approved wooden cleats projecting 25mm to 40mm from face of wall a fixing with clips of approved quality and number ,filing the joint using rubber gasket with solvent cement and properly resting the shoe of pipes on C.C. or masonry blocks, including necessary scaffolding and maintenance for 3 yrs for any leakages or dislocations of pipes. All the P.V.C. fittings and additional 2 piece socket clips shall be got approved from engineer

in charge etc. complete. Spec. No.:- As directed by Engineer Incharge

Providing and fixing H.D.P container one piece moulded water tank made out of low density polythyler and built corrugation including of delivery up to destination hoisting and fixing of accessories such as inlet, outlet overflow of all tanks capacity above 1000 to 20,000 litres Spec. No.:- As directed by engineer-in- charge.

Providing and fixing 40 mm. dia Ball cock medium type with PVC float including sockets and necessary fittings and tested as per municipal requirements etc. complete. Spec. No.:- As directed by Engineer in charge. A. Second Floor

Providing and fixing screw down for 32 mm dia. wheeled stop tap of brass including necessary sockets/union nut complete. Spec.No.:- Bd.V.9 Page No. 555 a)Second Floor

Providing and fixing 15cm x 10cm salt glazed stoneware gully trap in cement concrete 1:4:8 outside the building including cast iron grating in the sink, connecting glazed stoneware pipe, brick masonry chamber with cast iron lid and cast iron grating for the gully trap. Spec. No.:- Bd.V.38, Page Number 572

Providing and constructing Brick Masonry Inspection Chamber 60cm x 45cm x 90cm including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round G.S.W. pipes, Brick Masonry, plastering from inside and with frame fixed in cement concrete with R.C.C. Cover medium duty 140 kg with frame etc complete. Spec.No.:- Bd.V.43, Page No. 574

Providing and constructing Brick Masonry Inspection Chamber 90cm x 45cm x 90cm including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round G.S.W.pipes, Brick Masonry, plastering from inside and with frame fixed in cement concrete with R.C.C. Cover medium duty 140Kilogramwith frame etc complete. Spec. No.:- Bd.V.43, Page Number 574

Providing and constructing Brick Masonry inspection trap Chamber 90cm x 45cm including 1:4:8 C.C foundation, 1:2:4 C.C.channels/half round glazed stoneware pipe channel, salt glazed stone-ware intercepting trap with rodding pipe set in 1:4:8 cement concrete block, brick masonry plastering inside and Outside, fixed in cement concrete with R.C.C. Cover medium duty 140 Kilogram. etc complete Spec. No.:- Bd.V.44, Page Number 575

Providing and laying concrete pipes of I.S.NP. class of 150mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete. Spec.No.:- Bd.V.41, Page No. 573

Providing and laying concrete pipes of I.S.NP. class of 300mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete. Spec.No.:- Bd.V.41, Page No. 573

Providing and fixing reinforced cement concrete cover of size 60 cm x 45 cm with frame over inspection chamber etc. complete.Medium duty (100 Kilogram) Spec. No.:- As directed by Engineer in charge.

Providing and fixing C.P. Angular stop clock with wall flange of approved make continental including necessary sockets/union nut etc. complete. Spec. No.:- As directed by Engineer in charge

Providing and fixing 100 mm dia. chromium plated brass showers rose to 15mm dia. supply pipe including necessary bend and socket complete. Spec. No.:- Bd.V. 12 Page Number 556

Providing and fixing C.P. wall mixer with provision for overhead shower with 115mm long bend pipe and wall flange of approved make including necessary sockets/union nut etc. complete. Spec. No.:- As directed by Engineer in charge

Providing and fixing C.P. BIB cock with wall flange of approved make including necessary sockets/ union nut etc. complete. Spec. No.:- As directed by Engineer in charge

Removing chockes and leakages from down take G.I/CI/PVC pipe line on walls floor level by using zoola / scaffolding and rectify the same for functioning with all lifts etc. complete. Spec. No.:- As directed by Engineer in charge.

Manualy clearing the chockes from under ground drainage line including Inspection chambers with the help of required tools for propre functioning line chamber to chamber etc. complete. Spec. No.:- As directed by Engineer in charge.

Providing & Fixing 50 mm Artificial Grass, thick rubber underside, green grass with yellow strands give realistic look and feel. Spec. No.:- As directed by Engineer in charge.

Dismantling brick masonry in lime or cement mortar and stacking the materils as directed with all leads, lifts etc. Spec. No.:- As directed by Engineer in charge.

itemH1Code75

itemH1Code76

Providing preconstructional antitermite treatment as per I.S. 6313 (Part-II) by treating the top surface of plinth filling at the rate of 5 litres of emulsion concentrate at 1.0 percent of clorophyrifos per One Square Metre of surface area covering ten years guarantee on bond paper. Spec. No.:- As directed by Engineer in charge.

Filling in plinth and floors with contractors material/brought from outside and approved by Engineer incharge in layers of 15 cm to 20 cm including watering and compaction etc. complete. Spec. No.:- Bd.A.11 Page One Number 263

Compacting the hard murum side widths including laying in layers on each side with vibratory roller including artificial watering etc. complete. Spec. No.:- 0

Providing dry/ trap/ granite/ quartzite/ gneiss rubble stone soling 15 cm to 20 cm thick including hand packing and compacting etc. complete. Spec. No.:- Bd.A. 12 PageOne Number 264

Providing and laying Cast in situ/Ready Mix cement concrete in M15 of trap/ granite/quartzite/gneiss metal for foundation and bedding , Without SCADA

Providing and laying Cast in situ/Ready Mix cement concrete in M-10 of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including bailing out water, Steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) Spec. No.:- Bd. E. 1 Page One Number 287

Providing and fixing Ductile iron man hole cover of light / medium / heavy duty with frame of any size over inspection chamber etc.complete

Providing and fixing in position TMT - FE - 500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis,

Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 mm thick in cement mortar 1:4 using waterproofing compound at 1Kilogramper cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete. Spec. No.:- Bd.L.7 Page Number 369

copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete. Spec. No.:- Bd.F.17, Page One Number 306

Providing fly ash brick masonry with conventional / I.S. type fly ash bricks in C.M. 1:6 in foundation and plinth including bailing out water manually striking joints, racking out joints watering and scaffolding etc. complete. Spec. No.:- As director by engineer in charge and BDG-2 and 5

Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding etc. Complete Spec. No.:- Bd.G.5 Page One Number 315

Providing waterproof plaster in W.C. and bath 12 mm thick for dado in cement mortar 1:3 with neat finishing, floating using waterproofing compound at the rate of 1 Kilogram. per bag of cement of approved make and manufacturer and curing etc. complete. (Excluding Tiles) (As directed by Engineer in Charge) Spec. No.:- As directed by Engineer in charge.

Providing and applying two coats of exterior acraylic emulsion paint confirming to corresponding I.S. of approved manufacture and of approved colour to the plastered surfaces including cleaning ,preparing the plaster surface, applying primer coat ,scaffolding if necessary , and watering the surface for two days etc complete. Spec. No.:- As directed by Engineer in charge.

Providing and laying concrete pipes of I.S.NP. class of 150mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete. Spec. No.:- Bd.V.41, Page One Number 573

Providing preconstructional antitermite treatment as per I.S. 6313 (Part-II) by treating the bottom surface and sides of excavation at the rate of 5 litres of emulsion concentrate of 1.0 percent of chlorophyrifos per square meter of surface area covering 10 years guarantee on bond paper. Spec. No.:- As directed by Engineer in charge.

itemH1Code93

Removing doors and windows with frames and stacking the materials as directed with all leads, lifts etc. complete. Spec. No.:- As directed by Engineer in charge.

itemH1Code94

itemH1Code95

Removing teak wood trellies work with frame including stacking the materials as directed with all leads, lifts etc. complete.

Removing the existing cement plaster of any thickness without causing dust nuisance and stacking the debris upto a distance of 50 metres or spreading in the compound and cleaning the site etc.complete. Spec. No.:- As directed by Engineer in charge.

Providing antitermite treatment to the wooden frames of doors/windows of the existing building as perI.S.6313(Part-III) bydrilling 6mm dia.holes at four corners on one side and four corners on other side at a down wardangle of about 45 degree at the junction of wood work and masonary and injecting 150ml.of chlorodane 5% W.C.and sealing by filling putty etc. complete covering 2 years guarantee on bond paper.

Providing internal cement plaster 12mm thick in single coat in cement mortar 1:4 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etc. complete. Spec. No.:- Bd. L.2 Page Number 368

Providing antitermite treatment to the sides of flooring of the existing building as per I.S. 6313 (Part-III) by punching holes 6mm dia. drilled at a distance of 30cm. centre to centre and injecting one percent of chlorodane emulsion concentrate at the rate of 50 ml per hole and sealing by filling putty etc. complete covering 2 years guarantee on bond paper. Spec. No.:- As directed by Engineer in charge.

Providing antitermite treatment to the for interior surfaces of wall surfaces. Scope of Work •Making 3” wide x 9”deep trench along the wall & floor OR Drilling 12 mm diameter holes at the junction of Wall & Floor at 90° angle •Drilling 12 mm diameter holes, 12 inches deep at 1 feet distance C/C •Filling the holes with Termiticide Solution (1lit per hole) OR Applying Termiticide Solution @ 2.25 liter per linear meter in trenches •Filling the holes with cement mortar OR Filling the trenches with soil and treat the top surface with Termiticide Solution @ 1.0 ltr. Per linear meter •Customer is requested to put plinth protection complete covering 2 years guarantee on bond paper. Spec. No.:- As directed by Engineer in charge.

Transportation of excavated & debris from site to disposing site (lead 3km)

Providing Mirror polishing to Kota Stone including using all necessary stones and equipments cleaning, washing etc. complete. For Flooring. Spec. No.:- BDM 33.28, Page Number 158

Providing & Fixing in position Acoustical Doors along with 150x150mm teak wood frame, doors made from 50mm Teak wood frame 600x600ctoc filled with 1000 Gsm synthetic wool 50mm thick and 3mm Tecsound from both sides,12mm waterproof ply & veneer from both sides, including 150mm heavy duty SShinges (Geze /Dormaoreq.)4no each leaf, with Door-closer (Dorma/ Gezeoreq.) including cost of required Cut-Outs,decorative mouldings/ finishing-items/ melamine polish & Scaffolding as per Architectural & Acoustical Design & Instructions & Complete in all aspects.including all materials labour,finishing etc complete

Supply & installation of Anutone Salon Slats Surco made of pinewood E1 grade fiberboard, melamine/veneer laminated finish, groove perforated slats L16-2 - (2mm grooves @16mm pitch with 27% open area) / L32-2 - (2mm grooves @ 32mm centers with 15% open area) surface density 63g/m2,tongue-groove edge for a seamless look, 5-test fire retardant grade, size 128 x2440x16mm, volume density of base board 700Kg/m3, weight 9Kg/m2 (L16), 10.5Kg/m2 (L32), 11Kg/m2 (L64) installed by using Anutone Strut framework system. The Anutone Strut fram

Providing and applying priming coat on concrete/ masonar

ework system shall include Anutone Strut CC10 thickness 0.55mm, length 3600mm, knurled web 40mm, depth 10mm and equal flanges 15mm is fastened to the wall positioned vertically at every 600mm centres.Anutone Strut CC18,aluminium core cross channel, thickness 0.5mm, length 2400mm, web 15mm & 27mm, depth 18mm and flanges of 7mm with suitable edge & center brackets is then fixed perpendicular to the Strut CC10 with the help of fasteners at every 400mm centersAnutone Slats Surco Plus of size 128x 2440x16mm in then fixed perpendicular to Strut CC18 with suitable edge & centre brackets. Contractor to provide expansion joints of 3mm at every 4.88m length wise and 4.992m width wise. Note:-Wooden packing of appropriate thickness to be provided at rear of strut to bring finish inline with Subtex NRC finish. The system is backlined with Anutone SynthPF 10x10 adhered on wall with dab spots of Anutone stick S7 adhesive., including Anti Termite Treatement. Technical Parameters Product Picture • Fire (Class) – 1 & P • Acoustics – NRC 0.75( For L32 C40 Mounting)• Thermal conductivity (W/mk)– na• Climate (°C, RH) – 50, 70• Light reflectance (%) – 75 (Maple Arce)• Green (VOC, RC %) – E1, 25

Wood Panel for Walls, Back Fire Panel Spectator and Target Area :- Providing & Fixing Imported PineWood 25 mm thick 4" width, both side chamfering, Front side machine grinding for smooth surface with water based painting (Apex) on both front and rear sides etc.

Providing & Fixing of high grade, glass fibre reinforced acoustical gypsum wall dado of KNAUF DANOLINE DANOLOFT (3.5x3.5mm square perforation with c/c distance of 8.33mm) in 600x600x12.5mm. Its a concealed sysytem with system D+ giving seamless look with end to end perforation on the tile and screw fixed on Knauf Ceiling perimeter channels 31 x 27x 15 X 0.50mm with the help of nylon sleeves and Knauf Hammer fixing 6X 40 mm and suspending Knauf intermediate channels of 45 x 15 X 0.70 mm from the Knauf L angle and Wedge anchors 6 X 40 mm to be fixed at a distance of 1220mm and with the help of Knauf LN screws 3.5 X11 mm . Knauf Ceiling section 49 X79 X0.50 mm thick with flanges 7 mm each are fixed perpendicular to Knauf intermediate channel using in line on both horizontal and vertical levels . Screw fixing is done mechanically either with screw driver or drilling machine with suitable attachment. The tiles are painted , have Humidity Resistance (RH) of 90%, NRC 0.8 , Light Reflection: 82.6% according to DIN Norm 5036, Fire Performance Class A2-s1,d0 suitable for Green Building application, with Recycled content of 81% and weight 8 kg/m2. • Manufactured from high grade non-combustible glass fibre reinforced gypsum board produced according to EN 520. Including Anti Termite Treatement. Suspension: Concealed screw fixed system with Danoloft Screws • Distance between load-bearing sections c/c 300 mm. Sections width of 60mm. • Distance between hangers and spacers ≤ 900 mm. • Distance from wall to first hanger and spacer ≤ 100 mm. • Location of edge section: Lower edge of edge section = lower edge of finished ceiling. Price is including removal of wall panelling.

Providing & Fixing of high grade, glass fibre reinforced acoustical gypsum ceiling of KNAUF DANOLINE CONTUR UNITY 3 (3.5x3.5mm square perforation with c/c distance of 8.33mm) in 600x600x12.5mm. Its a concealed sysytem with system D+ giving seamless look with end to end perforation on the tile & point demountability. The tiles are pre painted with RAL 9003, have Humidity Resistance (RH) of 90%, NRC 0.8 , Light Reflection: 82.6% according to DIN Norm 5036, Fire Performance Class A2-s1,d0 suitable for Green Building application, with Recycled content of 81% and weight 8 kg/m2. • Manufactured from high grade non-combustible glass fibre reinforced gypsum board produced according to EN 520, including Anti Termite Treatement. Suspension: Concealed grid system • Distance between load-bearing sections c/c 600 mm. • Distance between hangers and spacers ≤ 1500 mm. • Distance from wall to first hanger and spacer ≤ 100 mm. • Location of edge section: Lower edge of edge section = lower edge of finished ceiling. Price is including removal of ceiling.

itemH1Code75

Filling in plinth and floors with contractors material/brought from outside and approved by Engineer incharge in layers of 15 cm to 20 cm including watering and compaction etc. complete. Spec. No.:- Bd.A.11 Page One Number 263

Providing and fixing Ductile iron man hole cover of light / medium / heavy duty with frame of any size over inspection chamber etc.complete

Providing dry/ trap/ granite/ quartzite/ gneiss rubble stone soling 15 cm to 20 cm thick including hand packing and compacting etc. complete. Spec. No.:- Bd.A. 12 PageOne Number 264

Providing and applying pearl/ luster finish paint of approved colour and shade to the

existing plaster surface including scaffolding, preparing the surface, applying the acrylic wall putti etc. complete. Spec.No.:- As directed by Engineer in charge.

Supply & Installation of 3.45 mm thick hetrogeneous PVC Vinyl flooring of certified by EN( Europian Standard) 14904, in rolls form of 2m wide and 23m long, total weight 3295 g/m2, Shock Absorption as per EN 14808 - 6%, Friction as per EN 13036-4 - 80 to 110, Vertical deformation as per EN 14809 - 0.4mm, Vertical Ball Behaviour as per EN 12235 - 98%, 100% recyclable, VOC emission after 28days lower than ≤10μg/m3, Phthalate Free. The laid flooring shall comply the fire rating CFL S1 as per EN 13501-The joints should be thermo welded with matching welding rods provided by the manufacturer. After welding the flooring will be seamless.The sub-surface should be absolutely at one level (Zero) for installing vinyl flooring.

Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.5 m.) By Mechanical Means Spec. No.:- Bd.A.1 Page One Number 259

Supply, Installation, testing & Commissioning of 6W Ceiling Surface Speaker (Ceiling Speaker + Back Box) with max SPL @1M/1W 88dB . Frequency response of 125Hz-16KHz. The speaker must have a metal grill & tappings at 6W/3W/1.5W. White color speaker with good aesthetics.

itemH1Code119

itemH1Code120

itemH1Code121

itemH1Code122

itemH1Code123

Supplying & laying HMS PVC conduit 25 mm dia with necessary accessories in RCC work/false ceiling/false flooring as per specification No. WG-MA/CC.

Supplying & erecting mains with 2x2.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG MA/BW

Supplying and erecting mains with 2x4 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW

Point wiring for light/bell hybrid type (Surface type under false ceiling and concealed type for drops & switch boards on walls) in min 20 mm PVC conduit / casing n capping with 1.5 sq.mm. (2+1E) FRLSH grade copper wires, modular type switch, earthing and required accessories as per specification No: WGPW/ HW

Supplying and erecting LED square / circular Max. 18 W down lighter/ Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 2000 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty.

Supplying and erecting anodized aluminium corridor / passage / mirror light LED fitting (2 feet) Max. 12W with high transitivity diffuser with min. system lumens output of 1200 lumens, min. efficacy of 100 lumen/W, CRI>80, CCT upto 6000K, Beam Angle of 110 deg., Ripple<5%, THD<10%, p.f. >0.95, operating range of 200-270V, surge protection of 2 kV, Life class of 50,000 Hrs. at L70B50, including driver with end caps on provided PVC Block / wooden board with 3 years warranty.

Supplying & erecting ready to use Retrofit T8 LED 18 / 20 tube light with polycarbonate body, heat sink, integrated HF electronic driver complete & compatible to T8 / T12 LED luminaire by disconnecting starter & ballast if necessary.

Supplying and erecting anodized aluminium corridor / passage light LED fitting (4 feet) Max. 22W with high transitivity diffuser with system lumens output of Min.2200 lumens , min. efficacy of 100 lumen/W, CRI>80, CCT upto 6000K, Beam Angle of 110 deg., Ripple<5%, THD<10%, p.f. >0.95, operating range of 200-270V, surge protection of 2 kV, Life class of 50,000 Hrs. at L70B50, including driver, with end caps on provided PVC Block / wooden board with 3 years warranty.

Sports Lighting SITC of Recessed monted 2'x2', 36W Recessed 2'X2' LED ceiling fixture with system outut≥4200lm. System efficacy is ≥120lm/W.product is with IP20 CRCA powder coated housing. Luminaire shall have satin finished translucence (HET) PC diffuser for Uniform illumination and wider light distribution. LM 80-08 compliant LEDs from reputed makes such as APT Electronics / Cree, / Bridgelux / Lumiled should be provided. LEDs used in the product shall comply with EN 62471 for Photo-biological safety and certificate for the same from manufacturer shall be provided. Luminaire shall use SMD type LED. The LED shall be compliant with LM80-08 standard with Useful L70 life of 50000 Hrs tested at maximum current. Proposed CCT s 6500K with CRI>80 & SDCM<5. Driver shuld be DALI comptible. Driver is having efficiency of minimum 85%. p.f. ≥0.95 & THD≤10%.Driver should have 4KV inbuit surge protection is g

iven. Driver should be able to operate at 140 V to 240 V AC supply.

Sports Lighting SITC of IP65 Syemmetric medium beam, 100W LED Floodlight luminaire with system efficacy of 110lm/W.system output should not be more than 11000lm for 100W. Power consumption of luminaire should not exceed 100W. CCT should be 5700K with CRI ≥ 70. The housing should be made of non-corrosive high-pressure die-cast aluminum to with stand extreme environments. It should have corrosion resistant powder coating to pass NSS of 500 Hrs. Product should be suitable for continuous operation (10-12 Hrs. per day). The Ingress protection should be minimum IP 66 with an IK rating of 08. Optical and control gear compartments shall be maintainable/replaceable without impacting the LED units. The access to the optical and the gear compartment should be separate.. The Luminaire should have a 4KV SPD duly bolted in the Luminaire .The luminaire should be of Class B Serviceability. The wattage of each LED should be greater than 1 watt and less than 3 Watt. Only high power Single white LED chip with ceramic based suitable for outdoor use is allowed. Multi Chip , array multi die , mid power ,Integrated arrays and COB’s are not permitted. The luminaire should be capable of withstanding voltage stress of 440V for 8 Hrs., should have an auto shutdown @ 325V and have an auto recovery feature. The Drivers should be with 0-10V dimable diver. Driver should have short circuit and open circuit protection. Luminaire and Driver both should be BIS approved and CRS no ( individual R no ) should be shared along with LM79 & LM80 during bid submission. Product should have Lifeclass of 50K hours @L70 with PF > 0.95 & THD ≤ 10%..product is designed to operate at (-10) Deg to45deg operating temp. 50,000 Hrs burning life is provided as per L70B50.

Sports Lighting SITC of 35W , Suspended / pendent mounted LED 1130mm Linar LED light. System output should not be more than 4000lm .System efficacy is 120lm/W. width of the product should be 50mm. Housing should be of CRCA powder coated with high Translucent Polystyrine Diffuser. Proposed CCT is 6500K along with CRI≥80.LM 80-08 compliant LEDs from reputed makes such asAPT Electronics / Cree, / Bridgelux / Lumiled should be provided. Product should have IP20 protection.LEDs used in the product shall comply with EN 62471 for Photo-biological safety and certificate for the same from manufacturer shall be provided.Driver shuld be DALI comptible. Driver is having p.f. ≥0.95 with iTHD≤10% Efficiency of driver shuld be minimum 90% with 4KV internal surge protection. Product is suitable to operate in 140 - 270V Ac range. Product should have inbuilt 4KV surge protection.. service life is 5000K as per L70B50.

SITC of Smart Panel with 63Amp 3 phase incomer and 2 outgoings of 32A 3Phase. Panel should have digital energy meter, control unit for monitoring and control, battery for control unit, SPD for control unit, CT, PT and current leak coil. Control unit should be compatible with 3phase and single phase power supply. It should be compatible for exchange of data through CAT6 cable or data sim card.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 2 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 3 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 4 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 6 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 8 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 12 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 16 / 18 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting modular type switch 6A / 10A duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type switch 16 / 20 A with indicator, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type 3 pin 6A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type 3 pin 6 / 16A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting energy saving ceiling fa

n 230 V A.C. 50 cycles 1200 mm complete erected in position as per specification no. FG-FN/CF

Point wiring for light/bell/exhaust fan in 20 mm FRLS grade HMS PVC conduit with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification No: WGPW/ SW.

Point wiring for ceiling fan (Surface type under false ceiling and concealed type for drops & switch boards on walls) in min 20 mm PVC conduit / casing n capping with 1.5 sq.mm. (2+1E) FRLSH grade copper wires, modular type switch, earthing and required accessories as per specification No: WG-PW/HW

Supplying, erecting & marking SPMCB 6A to 32A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking SPMCB 6A to 32A, B-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking SPMCB 40A to 63A, B-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking TPMCB 40A to 63A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking FPMCB 6A to 32A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking FPMCB 40A to 63A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying & erecting triple pole and neutral distribution board (TPNDB), SPMCB of 4 ways/phase (12 poles), with door, 1.2mm thickness, surface/flush mounted, IP 43 protection on iron/GI frame (horizontal busbar type) as per specification no. SW-SWR/MCBDB

Supplying & erecting triple pole and neutral distribution board (TPNDB), SPMCB of 8 ways / phase (24 poles), with door, 1.2mm thickness surface/ flush mounted, IP 43 Protection on iron/GI frame (horizontal busbar type) as per specification no. SW-SWR/MCBDB

Supplying and erecting single pole and neutral distribution board (SPNDB), with 2 ways for incoming and 10 ways (10 poles) for outgoing SP MCBs, with door, 1.2mm thickness surface / flush mounted, IP 43 Protection on iron / GI frame as per specification no. SW-SWR/MCBDB

Supplying and erecting fresh air cum exhaust fan of light duty 250 V A.C. 50 cycles 225mm. 1400 RPM rust proof body & blades, wire mesh, duly erected, complete.

Supplying and erecting electronic type step regulator for ceiling fan 600 / 900 / 1200/ 1400 mm. sweep, complete erected on provided switch board.

Supplying & erecting 2 pair telephone copper cable 0.5 mm dia. with high density polyethylene insulation, polyester taped, Nylon Rip Cord & grey colour sheathed with FR PVC, conforming to ITD specification S/WS 113C laid in provided PVC casing capping/conduit as per specification No. WG-TW

Providing & erecting hot dipped galvanised Perforated type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 150 mm width & 75 mm height complete with necessary coupler plates & hardware.

Providing & erecting hot dipped galvanised Perforated type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 300 mm width & 75 mm height complete with necessary coupler plates & hardware.

Supplying and erecting PVC box trunking of size 50x50 mm. with accessories on wall/ceiling as per specification No: WG-MA/BOX.

Supplying and erecting PVC box trunking of size 75x50 mm. with accessories on wall/ceiling as per specification No: WG-MA/BOX.

Supplying and erecting PVC box trunking of size 75x75 mm. with accessories on wall/ceiling as per specification No: WG-MA/BOX.

Supplying, erecting & commissioning 2 pole RCCB 16/25A, electromagnetic type with 30/100/300 mA sensitivity with earth leakage trip indication complete as per specification no. SW-RCCB/RCCB

Supplying, erecting & commissioning 2 pole RCCB 40A, electromagnetic type with 30/100/300 mA sensitivity with earth leakage trip indication complete as per specification no. SW-RCCB/RCCB

Supplying, erecting & commissioning 2 pole RCCB 63A, electromagnetic type with 30/100/300 mA sensitivity with earth leakage trip indication complete as per specification no. SW-RCCB/RCCB

Supplying, erecting & marking DPMCB 40A to 63A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying and erecting modular type switch 6A / 10A duly erected on provided plate and box with wiring connections complete.

Supplying, erecting & marking DPMCB 40A to 63A, B-series with rated short -circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying & erecting triple pole and neutral distribution board (TPNDB), SP/TP MCBs total 12 ways /36 poles, with door, 1.2mm thickness surface/flush mounted, IP 43 Protection on iron/GI frame (vertical busbar type) as per specification no. SW-SWR/MCBDB

Supplying & erecting CRCA sheet metal one way enclosures of 1.2mm thickness suitable for DP MCB /TP MCB/FP MCB/RCCB/RCBO complete erected on angle iron/GI frame.

Supplying & erecting CRCA sheet metal enclosures of 1.2mm thickness with 10A, 2 pin plug & earth socket and 10A, 3 pin plug top with 10A single pole MCB having rated short - circuit breaking capacity (Icn) 10kA complete erected on angle iron / GI frame.

Supplying & erecting CRCA sheet metal enclosures of 1.2mm thickness with 20A, 2 pin plug & earth socket and 20A, 3 pin plug top with 20A/30A single pole MCB having rated short - circuit breaking capacity (Icn) 10kA complete erected on angle iron/ GI frame.

Supplying & erecting CRCA sheet metal enclosures of 1.2mm thickness with 30 A, 3 pin plug & earth socket and 30A, 3 pin plug top with 30A triple pole MCB having rated short - circuit breaking capacity (Icn) 10kA complete erected on angle iron / GI frame.

Supplying and erecting HMS PVC conduit FRLS grade 32 mm dia. With PVC accessories on wall / ceiling as per specification No: WG-MA/CON.

Supplying and erecting electronic type step regulator for ceiling fan 600 / 900 / 1200/ 1400 mm. sweep, complete erected on provided switch board.

Supplying and erecting PVC insulated PVC round sheathed 2.5 sq.mm (50 no. x 0.25 mm dia.) 3 core flexible multi stranded copper Industrial cable for voltage grade up to 1.1 Kv

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 6 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL 8) For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 5 %

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 25 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL 8) For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 5 %

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 300 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL 8) For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 5 %

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3 core 4 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU 8) For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 5 %

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3 core 6 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per spec

ification no. CB-LT/CU 8) For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 5 %

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 4 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU 8) For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 5 %

itemH1Code119

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 6 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU 8) For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 5 %

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 10 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU 8) For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 5 %

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 16 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU 8) For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 5 %

Supplying & erecting triple pole and neutral distribution board (TPNDB), 3 pole/4 pole MCCB as incomer & outgoing SP MCB (36 poles) or TP MCB of 12 ways (36 poles), with door, 1.2mm thickness, surface/flush mounted, on iron/GI frame (vertical busbar type) as per specification no. SW-SWR/MCBDB1

Providing & erecting 3 Pole MCCB, 415V, 200A, rated short-circuit breaking capacity 25 kA (Ics=100% of Icu), adjustable thermal (overload) setting and adjustable magnetic setting with provided leads, provision for installation of shunt/UV/trip alarm contact and MCCB should have phase barriers both sides, with insulation withstand capacity 800V, no line-load bias in provided enclosure/panel as per specification no. SW-SWR/MCCB

Supplying and erecting terminal spreaders suitable for 3 pole, up to 250A MCCB (set of 6)

Supplying, erecting, testing and commissioning of 10kVA capacity online pure sine wave with backup time of 0.30 hrs. PWM & IGBT based UPS with 0.9 to unity output pf, 3 phase input & 1 phase output complete with all protections as per specification no. AP-UPS

DATA networking Supplying and installing cat-6 LSZH cable suitable for networking as peR specification no. WG-COC/NC

Supplying and fixing tool-less IO (Ethernet) flush/surface type in provided modular box as per specification no. WG-NAS/IO

Supplying, erecting & marking FPMCB 6A to 32A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 2 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting modular type blanking plate one module, duly erected on provided plate & box.

Supplying and fixing tool-less shutter keystone jack (RJ-45) in provided patch panel complete as per specification no. WG-NAS/KJ

Supplying and fixing 24 port patch panel with tool-less keystone jacks in provided U Rack complete as per specification no. WG-NAS/PP

Supplying and fixing 1 m length, UTP patch cord of enhanced Cat 6 type with 4-connector channel, performance test report as per ANSI/TIA-568.2-D in position as per specification No. WG-COC/PC

Supplying and fixing 3 m UTP patch cord of Cat 6 type in position as per specification No. WG-COC/PC

Supplying and fixing 9U wall mount rack (Dimension-DxWxH – 500x600x500 mm) as per specification No. WG-NAS/RAK

VOICE networking Supplying and erecting modular type telephone socket one gang with safety shutter, duly erected on provided plate and box with wiring connections complete.

Supplying, erecting & commissioning MDF Box 50x50 pairs made from min. 1.5mm thick MS sheet as per specification no. WG-TW

Supplying, erecting & commissioning MDF Box 100x100 pairs made from min. 1.5mm thick MS sheet as per specification no. WG-TW

Supplying & erecting co-axial copper cable low voltage grade tri-shielded RG- 6 as per specification No. WG-TW

Supplying & erecting co-axial copper cable low voltage grade tri-shielded RG- 11 as per specification No. WG-TW

Supplying and erecting modular type T.V. socket single outlet, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 1 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

FIRE ALARM SYSTEM EQUIPMENT Supplying, installing, testing and commissioning of addressable optical smoke detector, single/twin LED’s with 360 degree view, suitable for low voltage 15 to 32 V DC two wires supply, in-built locking mechanism to check the removal and pilferage of the detector, in built isolation mode, start up current 300μA and alarm condition current shall be maximum 6.5 mA, operating temperature 0°C to 50°C, humidity 0-95% RH, IP 41, conforming to IS 2189: 2008, 11360_1985_Reff2020 EN 54 or UL Approved with 3 years equipment replacement warranty FFAFAS/ SD.

Supplying, installing, testing and commissioning remote response indicators suitable to operate on 5 - 28 V dc supply having FR Polymer ABS Housing complete as per specification no. FF-FAAS/RRI

Supplying, installing, testing and commissioning of intelligent addressable thermal/heat detector with rate of rise cum fixed temperature thermistor complete with base as required, suitable for temperature variations from -20°C to 38°C for fixed-heat and rate-of-rise type detectors and 0°C to 66°C for high heat type detectors, in built isolation mode, suitable for offices/ceiling cable trenches/less ventilation area's etc. with 3 years equipment replacement warranty IS : 2175 - 1988 reaffirmed 2000, IS 15908:2021 standards FF-AFAS/SD.

Supplying, installing, testing and commissioning of addressable manual call points ( break glass type/pull station type), made of addressable break glass plastic square in shape surface/flush mounted with "Break Glass" massage embedded on the glass, complete erected with mounting base and required accessories conforming to EN 54 or UL listed with 3 years equipment replacement warranty FF-AFAS/MCP.

Supplying, installing, testing and commissioning of addressable fire control/ relay module complete as required, with 3 years equipment replacement warranty conforming to IS 5051Part 2 (Sec 1 to 3) : 1982 reed relays, EN 54 or UL Listed FF-AFAS/CRM.

Supplying, installing, testing and commissioning of addressable fire monitor module complete as required. EN 54 or UL Listed with 3 years equipment replacement warranty conforming to IS 5051Part 2 (Sec 1 to 3) : 1982 Reed relays FF-AFAS/MM.

Supplying, installing, testing and commissioning of intelligent addressable thermal/heat detector with rate of rise cum fixed temperature thermistor complete with base as required, suitable for temperature variations from -20°C to 38°C for fixed-heat and rate-of-rise type detectors and 0°C to 66°C for high heat type detectors, in built isolation mode, suitable for offices/ceiling cable trenches/less ventilation area's etc. with 3 years equipment replacement warranty IS : 2175 - 1988 reaffirmed 2000, IS 15908:2021 standards FF-AFAS/SD.

Supplying, installing, testing and commissioning of addressable fire isolator module complete as required. EN 54 /FM or UL Listed with 3 years equipment replacement warranty conforming to IS 5051Part 2 (Sec 1 to 3) : 1982 Reed relays FF-AFAS/ISM.

Supplying, installing

, testing and commissioning of addressable horn cum strobe sound/ hooter, output frequency 500 to 1000 Hz with dB as per Chart given in IS 15908:2021, with flashing at 1 Hz over the strobe’s entire operating voltage range EN 54, conforming to IS 2189: 2008, IS 15908:2021 standards with 3 years equipment replacement warranty FF-AFAS/SSH.

Supplying, installation, testing & commissioning of fire fighter telephone handset complete as required.

Supplying, installation, testing & commissioning of fire fighter phone. jack complete as required.

itemH1Code224

Dismantling brick masonry in lime or cement mortar and stacking the materils as directed with all leads, lifts etc. Spec. No.:- As directed by Engineer in charge.

itemH1Code75

itemH1Code76

Providing preconstructional antitermite treatment as per I.S. 6313 (Part-II) by treating the top surface of plinth filling at the rate of 5 litres of emulsion concentrate at 1.0 percent of clorophyrifos per One Square Metre of surface area covering ten years guarantee on bond paper. Spec. No.:- As directed by Engineer in charge.

Filling in plinth and floors with contractors material/brought from outside and approved by Engineer incharge in layers of 15 cm to 20 cm including watering and compaction etc. complete. Spec. No.:- Bd.A.11 Page One Number 263

Compacting the hard murum side widths including laying in layers on each side with vibratory roller including artificial watering etc. complete. Spec. No.:- 0

Providing dry/ trap/ granite/ quartzite/ gneiss rubble stone soling 15 cm to 20 cm thick including hand packing and compacting etc. complete. Spec. No.:- Bd.A. 12 PageOne Number 264

Providing and laying Cast in situ/Ready Mix cement concrete in M15 of trap/ granite/quartzite/gneiss metal for foundation and bedding , Without SCADA

Providing and laying Cast in situ/Ready Mix cement concrete in M-10 of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including bailing out water, Steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) Spec. No.:- Bd. E. 1 Page One Number 287

Providing and fixing Ductile iron man hole cover of light / medium / heavy duty with frame of any size over inspection chamber etc.complete

Providing and fixing in position TMT - FE - 500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis,

Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 mm thick in cement mortar 1:4 using waterproofing compound at 1Kilogramper cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete. Spec. No.:- Bd.L.7 Page Number 369

copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete. Spec. No.:- Bd.F.17, Page One Number 306

Providing fly ash brick masonry with conventional / I.S. type fly ash bricks in C.M. 1:6 in foundation and plinth including bailing out water manually striking joints, racking out joints watering and scaffolding etc. complete. Spec. No.:- As director by engineer in charge and BDG-2 and 5

Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding etc. Complete Spec. No.:- Bd.G.5 Page One Number 315

Providing waterproof plaster in W.C. and bath 12 mm thick for dado in cement mortar 1:3 with neat finishing, floating using waterproofing compound at the rate of 1 Kilogram. per bag of cement of approved make and manufacturer and curing etc. complete. (Excluding Tiles) (As directed by Engineer in Charge) Spec. No.:- As directed by Engineer in charge.

Providing and applying two coats of exterior acraylic emulsion paint confirming to corresponding I.S. of approved manufacture and of approved colour to the plastered surfaces including cleaning ,preparing the plaster surface, applying primer coat ,scaffolding if necessary , and watering the surface for two days etc complete. Spec. No.:- As directed by Engineer in charge.

Providing and laying concrete pipes of I.S.NP. class of 150mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete. Spec. No.:- Bd.V.41, Page One Number 573

itemH1Code229

itemH1Code93

Removing doors and windows with frames and stacking the materials as directed with all leads, lifts etc. complete. Spec. No.:- As directed by Engineer in charge.

itemH1Code94

itemH1Code95

Removing teak wood trellies work with frame including stacking the materials as directed with all leads, lifts etc. complete.

itemH1Code225

Providing antitermite treatment to the wooden frames of doors/windows of the existing building as perI.S.6313(Part-III) bydrilling 6mm dia.holes at four corners on one side and four corners on other side at a down wardangle of about 45 degree at the junction of wood work and masonary and injecting 150ml.of chlorodane 5% W.C.and sealing by filling putty etc. complete covering 2 years guarantee on bond paper.

Providing internal cement plaster 12mm thick in single coat in cement mortar 1:4 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etc. complete. Spec. No.:- Bd. L.2 Page Number 368

Providing antitermite treatment to the sides of flooring of the existing building as per I.S. 6313 (Part-III) by punching holes 6mm dia. drilled at a distance of 30cm. centre to centre and injecting one percent of chlorodane emulsion concentrate at the rate of 50 ml per hole and sealing by filling putty etc. complete covering 2 years guarantee on bond paper. Spec. No.:- As directed by Engineer in charge.

itemH1Code226

Transportation of excavated & debris from site to disposing site (lead 3km)

itemH1Code227

Providing & Fixing in position Acoustical Doors along with 150x150mm teak wood frame, doors made from 50mm Teak wood frame 600x600ctoc filled with 1000 Gsm synthetic wool 50mm thick and 3mm Tecsound from both sides,12mm waterproof ply & veneer from both sides, including 150mm heavy duty SShinges (Geze /Dormaoreq.)4no each leaf, with Door-closer (Dorma/ Gezeoreq.) including cost of required Cut-Outs,decorative mouldings/ finishing-items/ melamine polish & Scaffolding as per Architectural & Acoustical Design & Instructions & Complete in all aspects.including all materials labour,finishing etc complete

Supply & installation of Anutone Salon Slats Surco made of pinewood E1 grade fiberboard, melamine/veneer laminated finish, groove perforated slats L16-2 - (2mm grooves @16mm pitch with 27% open area) / L32-2 - (2mm grooves @ 32mm centers with 15% open area) surface density 63g/m2,tongue-groove edge for a seamless look, 5-test fire retardant grade, size 128 x2440x16mm, volume density of base board 700Kg/m3, weight 9Kg/m2 (L16), 10.5Kg/m2 (L32), 11Kg/m2 (L64) installed by using Anutone Strut framework system. The Anutone Strut fram

itemH1Code228

ework system shall include Anutone Strut CC10 thickness 0.55mm, length 3600mm, knurled web 40mm, depth 10mm and equal flanges 15mm is fastened to the wall positioned vertically at every 600mm centres.Anutone Strut CC18,aluminium core cross channel, thickness 0.5mm, length 2400mm, web 15mm & 27mm, depth 18mm and flanges of 7mm with suitable edge & center brackets is then fixed perpendicular to the Strut CC10 with the help of fasteners at every 400mm centersAnutone Slats Surco Plus of size 128x 2440x16mm in then fixed perpendicular to Strut CC18 with suitable edge & centre brackets. Contractor to provide expansion joints of 3mm at every 4.88m length wise and 4.992m width wise. Note:-Wooden packing of appropriate thickness to be provided at rear of strut to bring finish inline with Subtex NRC finish. The system is backlined with Anutone SynthPF 10x10 adhered on wall with dab spots of Anutone stick S7 adhesive., including Anti Termite Treatement. Technical Parameters Product Picture • Fire (Class) – 1 & P • Acoustics – NRC 0.75( For L32 C40 Mounting)• Thermal conductivity (W/mk)– na• Climate (°C, RH) – 50, 70• Light reflectance (%) – 75 (Maple Arce)• Green (VOC, RC %) – E1, 25

Wood Panel for Walls, Back Fire Panel Spectator and Target Area :- Providing & Fixing Imported PineWood 25 mm thick 4" width, both side chamfering, Front side machine grinding for smooth surface with water based painting (Apex) on both front and rear sides etc.

itemH1Code230

itemH1Code119

itemH1Code120

itemH1Code121

itemH1Code231

itemH1Code123

Supplying & laying HMS PVC conduit 25 mm dia with necessary accessories in RCC work/false ceiling/false flooring as per specification No. WG-MA/CC.

itemH1Code232

Supplying and erecting mains with 2x4 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW

Point wiring for light/bell hybrid type (Surface type under false ceiling and concealed type for drops & switch boards on walls) in min 20 mm PVC conduit / casing n capping with 1.5 sq.mm. (2+1E) FRLSH grade copper wires, modular type switch, earthing and required accessories as per specification No: WGPW/ HW

Supplying and erecting LED square / circular Max. 18 W down lighter/ Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 2000 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty.

Supplying and erecting anodized aluminium corridor / passage / mirror light LED fitting (2 feet) Max. 12W with high transitivity diffuser with min. system lumens output of 1200 lumens, min. efficacy of 100 lumen/W, CRI>80, CCT upto 6000K, Beam Angle of 110 deg., Ripple<5%, THD<10%, p.f. >0.95, operating range of 200-270V, surge protection of 2 kV, Life class of 50,000 Hrs. at L70B50, including driver with end caps on provided PVC Block / wooden board with 3 years warranty.

Supplying & erecting ready to use Retrofit T8 LED 18 / 20 tube light with polycarbonate body, heat sink, integrated HF electronic driver complete & compatible to T8 / T12 LED luminaire by disconnecting starter & ballast if necessary.

Supplying and erecting anodized aluminium corridor / passage light LED fitting (4 feet) Max. 22W with high transitivity diffuser with system lumens output of Min.2200 lumens , min. efficacy of 100 lumen/W, CRI>80, CCT upto 6000K, Beam Angle of 110 deg., Ripple<5%, THD<10%, p.f. >0.95, operating range of 200-270V, surge protection of 2 kV, Life class of 50,000 Hrs. at L70B50, including driver, with end caps on provided PVC Block / wooden board with 3 years warranty.

Sports Lighting SITC of Recessed monted 2'x2', 36W Recessed 2'X2' LED ceiling fixture with system outut≥4200lm. System efficacy is ≥120lm/W.product is with IP20 CRCA powder coated housing. Luminaire shall have satin finished translucence (HET) PC diffuser for Uniform illumination and wider light distribution. LM 80-08 compliant LEDs from reputed makes such as APT Electronics / Cree, / Bridgelux / Lumiled should be provided. LEDs used in the product shall comply with EN 62471 for Photo-biological safety and certificate for the same from manufacturer shall be provided. Luminaire shall use SMD type LED. The LED shall be compliant with LM80-08 standard with Useful L70 life of 50000 Hrs tested at maximum current. Proposed CCT s 6500K with CRI>80 & SDCM<5. Driver shuld be DALI comptible. Driver is having efficiency of minimum 85%. p.f. ≥0.95 & THD≤10%.Driver should have 4KV inbuit surge protection is g

iven. Driver should be able to operate at 140 V to 240 V AC supply.

Sports Lighting SITC of IP65 Syemmetric medium beam, 100W LED Floodlight luminaire with system efficacy of 110lm/W.system output should not be more than 11000lm for 100W. Power consumption of luminaire should not exceed 100W. CCT should be 5700K with CRI ≥ 70. The housing should be made of non-corrosive high-pressure die-cast aluminum to with stand extreme environments. It should have corrosion resistant powder coating to pass NSS of 500 Hrs. Product should be suitable for continuous operation (10-12 Hrs. per day). The Ingress protection should be minimum IP 66 with an IK rating of 08. Optical and control gear compartments shall be maintainable/replaceable without impacting the LED units. The access to the optical and the gear compartment should be separate.. The Luminaire should have a 4KV SPD duly bolted in the Luminaire .The luminaire should be of Class B Serviceability. The wattage of each LED should be greater than 1 watt and less than 3 Watt. Only high power Single white LED chip with ceramic based suitable for outdoor use is allowed. Multi Chip , array multi die , mid power ,Integrated arrays and COB’s are not permitted. The luminaire should be capable of withstanding voltage stress of 440V for 8 Hrs., should have an auto shutdown @ 325V and have an auto recovery feature. The Drivers should be with 0-10V dimable diver. Driver should have short circuit and open circuit protection. Luminaire and Driver both should be BIS approved and CRS no ( individual R no ) should be shared along with LM79 & LM80 during bid submission. Product should have Lifeclass of 50K hours @L70 with PF > 0.95 & THD ≤ 10%..product is designed to operate at (-10) Deg to45deg operating temp. 50,000 Hrs burning life is provided as per L70B50.

Sports Lighting SITC of 35W , Suspended / pendent mounted LED 1130mm Linar LED light. System output should not be more than 4000lm .System efficacy is 120lm/W. width of the product should be 50mm. Housing should be of CRCA powder coated with high Translucent Polystyrine Diffuser. Proposed CCT is 6500K along with CRI≥80.LM 80-08 compliant LEDs from reputed makes such asAPT Electronics / Cree, / Bridgelux / Lumiled should be provided. Product should have IP20 protection.LEDs used in the product shall comply with EN 62471 for Photo-biological safety and certificate for the same from manufacturer shall be provided.Driver shuld be DALI comptible. Driver is having p.f. ≥0.95 with iTHD≤10% Efficiency of driver shuld be minimum 90% with 4KV internal surge protection. Product is suitable to operate in 140 - 270V Ac range. Product should have inbuilt 4KV surge protection.. service life is 5000K as per L70B50.

SITC of Smart Panel with 63Amp 3 phase incomer and 2 outgoings of 32A 3Phase. Panel should have digital energy meter, control unit for monitoring and control, battery for control unit, SPD for control unit, CT, PT and current leak coil. Control unit should be compatible with 3phase and single phase power supply. It should be compatible for exchange of data through CAT6 cable or data sim card.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 2 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 3 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 4 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 6 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 8 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 12 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 16 / 18 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting modular type switch 6A / 10A duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type switch 16 / 20 A with indicator, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type 3 pin 6A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete.

Open To Sky Area Development-50 meter Range Building:- Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50

Supplying and erecting energy saving ceiling fa

n 230 V A.C. 50 cycles 1200 mm complete erected in position as per specification no. FG-FN/CF

Point wiring for light/bell/exhaust fan in 20 mm FRLS grade HMS PVC conduit with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification No: WGPW/ SW.

Point wiring for ceiling fan (Surface type under false ceiling and concealed type for drops & switch boards on walls) in min 20 mm PVC conduit / casing n capping with 1.5 sq.mm. (2+1E) FRLSH grade copper wires, modular type switch, earthing and required accessories as per specification No: WG-PW/HW

Supplying, erecting & marking SPMCB 6A to 32A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking SPMCB 6A to 32A, B-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking SPMCB 40A to 63A, B-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 3.00 m.) By Manual Means Spec. No.:- Bd.A.1 Page Number 259

Supplying, erecting & marking FPMCB 40A to 63A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying & erecting triple pole and neutral distribution board (TPNDB), SPMCB of 4 ways/phase (12 poles), with door, 1.2mm thickness, surface/flush mounted, IP 43 protection on iron/GI frame (horizontal busbar type) as per specification no. SW-SWR/MCBDB

Supplying & erecting triple pole and neutral distribution board (TPNDB), SPMCB of 8 ways / phase (24 poles), with door, 1.2mm thickness surface/ flush mounted, IP 43 Protection on iron/GI frame (horizontal busbar type) as per specification no. SW-SWR/MCBDB

Supplying and erecting single pole and neutral distribution board (SPNDB), with 2 ways for incoming and 10 ways (10 poles) for outgoing SP MCBs, with door, 1.2mm thickness surface / flush mounted, IP 43 Protection on iron / GI frame as per specification no. SW-SWR/MCBDB

Supplying and erecting fresh air cum exhaust fan of light duty 250 V A.C. 50 cycles 225mm. 1400 RPM rust proof body & blades, wire mesh, duly erected, complete.

Providing antitermite treatment to the for interior surfaces of floor, wall. Scope of Work •Making 3” wide x 9”deep trench along the wall & floor OR Drilling 12 mm diameter holes at the junction of Wall & Floor at 90° angle •Drilling 12 mm diameter holes, 12 inches deep at 1 feet distance C/C •Filling the holes with Termiticide Solution (1lit per hole) OR Applying Termiticide Solution @ 2.25 liter per linear meter in trenches •Filling the holes with cement mortar OR Filling the trenches with soil and treat the top surface with Termiticide Solution @ 1.0 ltr. Per linear meter •Customer is requested to put plinth protection complete covering 2 years guarantee on bond paper. Spec. No.:- As directed by Engineer in charge.

Providing & Fixing in position Acoustical Doors along with 150x150mm teak wood frame, doors made from 50mm Teak wood frame 600x600ctoc filled with 1000 Gsm synthetic wool 50mm thick and 3mm Tecsound from both sides,12mm waterproof ply & veneer from both sides, including 150mm heavy duty SShinges(Geze/Dormaoreq.)4no each leaf,withDoor-closer(Dorma/Gezeoreq.)including cost of required Cut-Outs,decorative mouldings/finishing-items/melamine polish & Scaffolding as per Architectural & Acoustical Design & Instructions & Complete in all aspects.including all materials labour,finishing etc complete

Wood Panel for Walls, Back Fire Panel Spectator and Target Area Providing & Fixing Imported PineWood 25 mm thick 4" width, both side chamfering, Front side machine grinding for smooth surface with water based painting (Apex) on both front and rear sides etc.

Providing & erecting hot dipped galvanised Perforated type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 300 mm width & 75 mm height complete with necessary coupler plates & hardware.

Supplying and erecting PVC box trunking of size 50x50 mm. with accessories on wall/ceiling as per specification No: WG-MA/BOX.

Supplying and erecting PVC box trunking of size 75x50 mm. with accessories on wall/ceiling as per specification No: WG-MA/BOX.

Supplying and erecting PVC box trunking of size 75x75 mm. with accessories on wall/ceiling as per specification No: WG-MA/BOX.

Supplying, erecting & commissioning 2 pole RCCB 16/25A, electromagnetic type with 30/100/300 mA sensitivity with earth leakage trip indication complete as per specification no. SW-RCCB/RCCB

Supplying, erecting & commissioning 2 pole RCCB 40A, electromagnetic type with 30/100/300 mA sensitivity with earth leakage trip indication complete as per specification no. SW-RCCB/RCCB

Supplying, erecting & commissioning 2 pole RCCB 63A, electromagnetic type with 30/100/300 mA sensitivity with earth leakage trip indication complete as per specification no. SW-RCCB/RCCB

Supplying, erecting & marking DPMCB 40A to 63A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying and erecting modular type switch 6A / 10A duly erected on provided plate and box with wiring connections complete.

m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 3.00 m.) By Manual Means Spec. No.:- Bd.A.1 Page Number 259

Providing and applying priming coat on concrete/ masonary/ Asbestos Cement plastered surfaces including scaffolding if necessary, preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and sand papering as required etc. complete.

Supplying & erecting CRCA sheet metal one way enclosures of 1.2mm thickness suitable for DP MCB /TP MCB/FP MCB/RCCB/RCBO complete erected on angle iron/GI frame.

Supplying & erecting CRCA sheet metal enclosures of 1.2mm thickness with 10A, 2 pin plug & earth socket and 10A, 3 pin plug top with 10A single pole MCB having rated short - circuit breaking capacity (Icn) 10kA complete erected on angle iron / GI frame.

Supplying & erecting CRCA sheet metal enclosures of 1.2mm thickness with 20A, 2 pin plug & earth socket and 20A, 3 pin plug top with 20A/30A single pole MCB having rated short - circuit breaking capacity (Icn) 10kA complete erected on angle iron/ GI frame.

Supplying & erecting CRCA sheet metal enclosures of 1.2mm thickness with 30 A, 3 pin plug & earth socket and 30A, 3 pin plug top with 30A triple pole MCB having rated short - circuit breaking capacity (Icn) 10kA complete erected on angle iron / GI frame.

Supplying and erecting HMS PVC conduit FRLS grade 32 mm dia. With PVC accessories on wall / ceiling as per specification No: WG-MA/CON.

Supplying and erecting electronic type step regulator for ceiling fan 600 / 900 / 1200/ 1400 mm. sweep, complete erected on provided switch board.

Supplying and erecting PVC insulated PVC round sheathed 2.5 sq.mm (50 no. x 0.25 mm dia.) 3 core flexible multi stranded copper Industrial cable for voltage grade up to 1.1 Kv

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 6 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL 8) For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 5 %

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 25 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL 8) For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 5 %

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 300 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL 8) For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 5 %

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3 core 4 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU 8) For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 5 %

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3 core 6 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per spec

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 4 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU 8) For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 5 %

itemH1Code119

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 6 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU 8) For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 5 %

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 10 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU 8) For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 5 %

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 16 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU 8) For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 5 %

Supplying & erecting triple pole and neutral distribution board (TPNDB), 3 pole/4 pole MCCB as incomer & outgoing SP MCB (36 poles) or TP MCB of 12 ways (36 poles), with door, 1.2mm thickness, surface/flush mounted, on iron/GI frame (vertical busbar type) as per specification no. SW-SWR/MCBDB1

Providing & erecting 3 Pole MCCB, 415V, 200A, rated short-circuit breaking capacity 25 kA (Ics=100% of Icu), adjustable thermal (overload) setting and adjustable magnetic setting with provided leads, provision for installation of shunt/UV/trip alarm contact and MCCB should have phase barriers both sides, with insulation withstand capacity 800V, no line-load bias in provided enclosure/panel as per specification no. SW-SWR/MCCB

Supplying and erecting terminal spreaders suitable for 3 pole, up to 250A MCCB (set of 6)

Supplying, erecting, testing and commissioning of 10kVA capacity online pure sine wave with backup time of 0.30 hrs. PWM & IGBT based UPS with 0.9 to unity output pf, 3 phase input & 1 phase output complete with all protections as per specification no. AP-UPS

DATA networking Supplying and installing cat-6 LSZH cable suitable for networking as peR specification no. WG-COC/NC

Supplying and fixing tool-less IO (Ethernet) flush/surface type in provided modular box as per specification no. WG-NAS/IO

Supplying, erecting & marking FPMCB 6A to 32A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 2 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting modular type blanking plate one module, duly erected on provided plate & box.

Supplying and fixing tool-less shutter keystone jack (RJ-45) in provided patch panel complete as per specification no. WG-NAS/KJ

Supplying and fixing 24 port patch panel with tool-less keystone jacks in provided U Rack complete as per specification no. WG-NAS/PP

Supplying and fixing 1 m length, UTP patch cord of enhanced Cat 6 type with 4-connector channel, performance test report as per ANSI/TIA-568.2-D in position as per specification No. WG-COC/PC

Supplying and fixing 3 m UTP patch cord of Cat 6 type in position as per specification No. WG-COC/PC

Supplying, installing, testing and commissioning of addressable fire isolator module complete as required. EN 54 /FM or UL Listed with 3 years equipment replacement warranty conforming to IS 5051Part 2 (Sec 1 to 3) : 1982 Reed relays FF-AFAS/ISM.

Supplying, installing

, testing and commissioning of addressable horn cum strobe sound/ hooter, output frequency 500 to 1000 Hz with dB as per Chart given in IS 15908:2021, with flashing at 1 Hz over the strobe’s entire operating voltage range EN 54, conforming to IS 2189: 2008, IS 15908:2021 standards with 3 years equipment replacement warranty FF-AFAS/SSH.

Supplying, installation, testing & commissioning of fire fighter telephone handset complete as required.

Supplying, installation, testing & commissioning of fire fighter phone. jack complete as required.

itemH1Code352

Dismantling brick masonry in lime or cement mortar and stacking the materils as directed with all leads, lifts etc. Spec. No.:- As directed by Engineer in charge.

itemH1Code75

itemH1Code76

Providing preconstructional antitermite treatment as per I.S. 6313 (Part-II) by treating the top surface of plinth filling at the rate of 5 litres of emulsion concentrate at 1.0 percent of clorophyrifos per One Square Metre of surface area covering ten years guarantee on bond paper. Spec. No.:- As directed by Engineer in charge.

Filling in plinth and floors with contractors material/brought from outside and approved by Engineer incharge in layers of 15 cm to 20 cm including watering and compaction etc. complete. Spec. No.:- Bd.A.11 Page One Number 263

Compacting the hard murum side widths including laying in layers on each side with vibratory roller including artificial watering etc. complete. Spec. No.:- 0

Providing dry/ trap/ granite/ quartzite/ gneiss rubble stone soling 15 cm to 20 cm thick including hand packing and compacting etc. complete. Spec. No.:- Bd.A. 12 PageOne Number 264

Providing and laying Cast in situ/Ready Mix cement concrete in M15 of trap/ granite/quartzite/gneiss metal for foundation and bedding , Without SCADA

Providing and laying Cast in situ/Ready Mix cement concrete in M-10 of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including bailing out water, Steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) Spec. No.:- Bd. E. 1 Page One Number 287

Providing and fixing Ductile iron man hole cover of light / medium / heavy duty with frame of any size over inspection chamber etc.complete

Providing and fixing in position TMT - FE - 500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis,

Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 mm thick in cement mortar 1:4 using waterproofing compound at 1Kilogramper cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete. Spec. No.:- Bd.L.7 Page Number 369

copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete. Spec. No.:- Bd.F.17, Page One Number 306

Providing fly ash brick masonry with conventional / I.S. type fly ash bricks in C.M. 1:6 in foundation and plinth including bailing out water manually striking joints, racking out joints watering and scaffolding etc. complete. Spec. No.:- As director by engineer in charge and BDG-2 and 5

Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding etc. Complete Spec. No.:- Bd.G.5 Page One Number 315

Providing waterproof plaster in W.C. and bath 12 mm thick for dado in cement mortar 1:3 with neat finishing, floating using waterproofing compound at the rate of 1 Kilogram. per bag of cement of approved make and manufacturer and curing etc. complete. (Excluding Tiles) (As directed by Engineer in Charge) Spec. No.:- As directed by Engineer in charge.

Providing and applying two coats of exterior acraylic emulsion paint confirming to corresponding I.S. of approved manufacture and of approved colour to the plastered surfaces including cleaning ,preparing the plaster surface, applying primer coat ,scaffolding if necessary , and watering the surface for two days etc complete. Spec. No.:- As directed by Engineer in charge.

Providing and laying concrete pipes of I.S.NP. class of 150mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete. Spec. No.:- Bd.V.41, Page One Number 573

itemH1Code355

itemH1Code93

Removing doors and windows with frames and stacking the materials as directed with all leads, lifts etc. complete. Spec. No.:- As directed by Engineer in charge.

itemH1Code94

itemH1Code95

Removing teak wood trellies work with frame including stacking the materials as directed with all leads, lifts etc. complete.

itemH1Code353

Providing antitermite treatment to the wooden frames of doors/windows of the existing building as perI.S.6313(Part-III) bydrilling 6mm dia.holes at four corners on one side and four corners on other side at a down wardangle of about 45 degree at the junction of wood work and masonary and injecting 150ml.of chlorodane 5% W.C.and sealing by filling putty etc. complete covering 2 years guarantee on bond paper.

Providing internal cement plaster 12mm thick in single coat in cement mortar 1:4 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etc. complete. Spec. No.:- Bd. L.2 Page Number 368

Providing antitermite treatment to the sides of flooring of the existing building as per I.S. 6313 (Part-III) by punching holes 6mm dia. drilled at a distance of 30cm. centre to centre and injecting one percent of chlorodane emulsion concentrate at the rate of 50 ml per hole and sealing by filling putty etc. complete covering 2 years guarantee on bond paper. Spec. No.:- As directed by Engineer in charge.

itemH1Code226

Transportation of excavated & debris from site to disposing site (lead 3km)

itemH1Code227

Providing & Fixing in position Acoustical Doors along with 150x150mm teak wood frame, doors made from 50mm Teak wood frame 600x600ctoc filled with 1000 Gsm synthetic wool 50mm thick and 3mm Tecsound from both sides,12mm waterproof ply & veneer from both sides, including 150mm heavy duty SShinges (Geze /Dormaoreq.)4no each leaf, with Door-closer (Dorma/ Gezeoreq.) including cost of required Cut-Outs,decorative mouldings/ finishing-items/ melamine polish & Scaffolding as per Architectural & Acoustical Design & Instructions & Complete in all aspects.including all materials labour,finishing etc complete

Supply & installation of Anutone Salon Slats Surco made of pinewood E1 grade fiberboard, melamine/veneer laminated finish, groove perforated slats L16-2 - (2mm grooves @16mm pitch with 27% open area) / L32-2 - (2mm grooves @ 32mm centers with 15% open area) surface density 63g/m2,tongue-groove edge for a seamless look, 5-test fire retardant grade, size 128 x2440x16mm, volume density of base board 700Kg/m3, weight 9Kg/m2 (L16), 10.5Kg/m2 (L32), 11Kg/m2 (L64) installed by using Anutone Strut framework system. The Anutone Strut fram

Providing and applying priming coat on concrete/ masonar

ework system shall include Anutone Strut CC10 thickness 0.55mm, length 3600mm, knurled web 40mm, depth 10mm and equal flanges 15mm is fastened to the wall positioned vertically at every 600mm centres.Anutone Strut CC18,aluminium core cross channel, thickness 0.5mm, length 2400mm, web 15mm & 27mm, depth 18mm and flanges of 7mm with suitable edge & center brackets is then fixed perpendicular to the Strut CC10 with the help of fasteners at every 400mm centersAnutone Slats Surco Plus of size 128x 2440x16mm in then fixed perpendicular to Strut CC18 with suitable edge & centre brackets. Contractor to provide expansion joints of 3mm at every 4.88m length wise and 4.992m width wise. Note:-Wooden packing of appropriate thickness to be provided at rear of strut to bring finish inline with Subtex NRC finish. The system is backlined with Anutone SynthPF 10x10 adhered on wall with dab spots of Anutone stick S7 adhesive., including Anti Termite Treatement. Technical Parameters Product Picture • Fire (Class) – 1 & P • Acoustics – NRC 0.75( For L32 C40 Mounting)• Thermal conductivity (W/mk)– na• Climate (°C, RH) – 50, 70• Light reflectance (%) – 75 (Maple Arce)• Green (VOC, RC %) – E1, 25

itemH1Code354

Providing & Fixing of high grade, glass fibre reinforced acoustical gypsum wall dado of KNAUF DANOLINE DANOLOFT (3.5x3.5mm square perforation with c/c distance of 8.33mm) in 600x600x12.5mm. Its a concealed sysytem with system D+ giving seamless look with end to end perforation on the tile and screw fixed on Knauf Ceiling perimeter channels 31 x 27x 15 X 0.50mm with the help of nylon sleeves and Knauf Hammer fixing 6X 40 mm and suspending Knauf intermediate channels of 45 x 15 X 0.70 mm from the Knauf L angle and Wedge anchors 6 X 40 mm to be fixed at a distance of 1220mm and with the help of Knauf LN screws 3.5 X11 mm . Knauf Ceiling section 49 X79 X0.50 mm thick with flanges 7 mm each are fixed perpendicular to Knauf intermediate channel using in line on both horizontal and vertical levels . Screw fixing is done mechanically either with screw driver or drilling machine with suitable attachment. The tiles are painted , have Humidity Resistance (RH) of 90%, NRC 0.8 , Light Reflection: 82.6% according to DIN Norm 5036, Fire Performance Class A2-s1,d0 suitable for Green Building application, with Recycled content of 81% and weight 8 kg/m2. • Manufactured from high grade non-combustible glass fibre reinforced gypsum board produced according to EN 520. Including Anti Termite Treatement. Suspension: Concealed screw fixed system with Danoloft Screws • Distance between load-bearing sections c/c 300 mm. Sections width of 60mm. • Distance between hangers and spacers ≤ 900 mm. • Distance from wall to first hanger and spacer ≤ 100 mm. • Location of edge section: Lower edge of edge section = lower edge of finished ceiling. Price is including removal of wall panelling.

Providing & Fixing of high grade, glass fibre reinforced acoustical gypsum ceiling of KNAUF DANOLINE CONTUR UNITY 3 (3.5x3.5mm square perforation with c/c distance of 8.33mm) in 600x600x12.5mm. Its a concealed sysytem with system D+ giving seamless look with end to end perforation on the tile & point demountability. The tiles are pre painted with RAL 9003, have Humidity Resistance (RH) of 90%, NRC 0.8 , Light Reflection: 82.6% according to DIN Norm 5036, Fire Performance Class A2-s1,d0 suitable for Green Building application, with Recycled content of 81% and weight 8 kg/m2. • Manufactured from high grade non-combustible glass fibre reinforced gypsum board produced according to EN 520, including Anti Termite Treatement. Suspension: Concealed grid system • Distance between load-bearing sections c/c 600 mm. • Distance between hangers and spacers ≤ 1500 mm. • Distance from wall to first hanger and spacer ≤ 100 mm. • Location of edge section: Lower edge of edge section = lower edge of finished ceiling. Price is including removal of ceiling.

itemH1Code75

Filling in plinth and floors with contractors material/brought from outside and approved by Engineer incharge in layers of 15 cm to 20 cm including watering and compaction etc. complete. Spec. No.:- Bd.A.11 Page One Number 263

Providing and fixing Ductile iron man hole cover of light / medium / heavy duty with frame of any size over inspection chamber etc.complete

Providing dry/ trap/ granite/ quartzite/ gneiss rubble stone soling 15 cm to 20 cm thick including hand packing and compacting etc. complete. Spec. No.:- Bd.A. 12 PageOne Number 264

Providing and applying pearl/ luster finish paint of approved colour and shade to the

existing plaster surface including scaffolding, preparing the surface, applying the acrylic wall putti etc. complete. Spec.No.:- As directed by Engineer in charge.

Supply & Installation of 3.45 mm thick hetrogeneous PVC Vinyl flooring of certified by EN( Europian Standard) 14904, in rolls form of 2m wide and 23m long, total weight 3295 g/m2, Shock Absorption as per EN 14808 - 6%, Friction as per EN 13036-4 - 80 to 110, Vertical deformation as per EN 14809 - 0.4mm, Vertical Ball Behaviour as per EN 12235 - 98%, 100% recyclable, VOC emission after 28days lower than ≤10μg/m3, Phthalate Free. The laid flooring shall comply the fire rating CFL S1 as per EN 13501-The joints should be thermo welded with matching welding rods provided by the manufacturer. After welding the flooring will be seamless.The sub-surface should be absolutely at one level (Zero) for installing vinyl flooring.

Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.5 m.) By Mechanical Means Spec. No.:- Bd.A.1 Page One Number 259

Supply, Installation, testing & Commissioning of 6W Ceiling Recessed Speaker with max SPL @1M/1W 88dB . Frequency response of 125Hz-16KHz. The speaker must have a metal grill & tappings at 6W/3W/1.5W. White color speaker with good aesthetics.

itemH1Code119

itemH1Code120

itemH1Code121

itemH1Code231

itemH1Code123

Supplying & laying HMS PVC conduit 25 mm dia with necessary accessories in RCC work/false ceiling/false flooring as per specification No. WG-MA/CC.

itemH1Code232

Supplying and erecting mains with 2x4 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW

Point wiring for light/bell hybrid type (Surface type under false ceiling and concealed type for drops & switch boards on walls) in min 20 mm PVC conduit / casing n capping with 1.5 sq.mm. (2+1E) FRLSH grade copper wires, modular type switch, earthing and required accessories as per specification No: WGPW/ HW

Supplying and erecting LED square / circular Max. 18 W down lighter/ Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 2000 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty.

Supplying and erecting anodized aluminium corridor / passage / mirror light LED fitting (2 feet) Max. 12W with high transitivity diffuser with min. system lumens output of 1200 lumens, min. efficacy of 100 lumen/W, CRI>80, CCT upto 6000K, Beam Angle of 110 deg., Ripple<5%, THD<10%, p.f. >0.95, operating range of 200-270V, surge protection of 2 kV, Life class of 50,000 Hrs. at L70B50, including driver with end caps on provided PVC Block / wooden board with 3 years warranty.

Supplying & erecting ready to use Retrofit T8 LED 18 / 20 tube light with polycarbonate body, heat sink, integrated HF electronic driver complete & compatible to T8 / T12 LED luminaire by disconnecting starter & ballast if necessary.

Supplying and erecting anodized aluminium corridor / passage light LED fitting (4 feet) Max. 22W with high transitivity diffuser with system lumens output of Min.2200 lumens , min. efficacy of 100 lumen/W, CRI>80, CCT upto 6000K, Beam Angle of 110 deg., Ripple<5%, THD<10%, p.f. >0.95, operating range of 200-270V, surge protection of 2 kV, Life class of 50,000 Hrs. at L70B50, including driver, with end caps on provided PVC Block / wooden board with 3 years warranty.

Sports Lighting SITC of Recessed monted 2'x2', 36W Recessed 2'X2' LED ceiling fixture with system outut≥4200lm. System efficacy is ≥120lm/W.product is with IP20 CRCA powder coated housing. Luminaire shall have satin finished translucence (HET) PC diffuser for Uniform illumination and wider light distribution. LM 80-08 compliant LEDs from reputed makes such as APT Electronics / Cree, / Bridgelux / Lumiled should be provided. LEDs used in the product shall comply with EN 62471 for Photo-biological safety and certificate for the same from manufacturer shall be provided. Luminaire shall use SMD type LED. The LED shall be compliant with LM80-08 standard with Useful L70 life of 50000 Hrs tested at maximum current. Proposed CCT s 6500K with CRI>80 & SDCM<5. Driver shuld be DALI comptible. Driver is having efficiency of minimum 85%. p.f. ≥0.95 & THD≤10%.Driver should have 4KV inbuit surge protection is g

iven. Driver should be able to operate at 140 V to 240 V AC supply.

Sports Lighting SITC of IP65 Syemmetric medium beam, 100W LED Floodlight luminaire with system efficacy of 110lm/W.system output should not be more than 11000lm for 100W. Power consumption of luminaire should not exceed 100W. CCT should be 5700K with CRI ≥ 70. The housing should be made of non-corrosive high-pressure die-cast aluminum to with stand extreme environments. It should have corrosion resistant powder coating to pass NSS of 500 Hrs. Product should be suitable for continuous operation (10-12 Hrs. per day). The Ingress protection should be minimum IP 66 with an IK rating of 08. Optical and control gear compartments shall be maintainable/replaceable without impacting the LED units. The access to the optical and the gear compartment should be separate.. The Luminaire should have a 4KV SPD duly bolted in the Luminaire .The luminaire should be of Class B Serviceability. The wattage of each LED should be greater than 1 watt and less than 3 Watt. Only high power Single white LED chip with ceramic based suitable for outdoor use is allowed. Multi Chip , array multi die , mid power ,Integrated arrays and COB’s are not permitted. The luminaire should be capable of withstanding voltage stress of 440V for 8 Hrs., should have an auto shutdown @ 325V and have an auto recovery feature. The Drivers should be with 0-10V dimable diver. Driver should have short circuit and open circuit protection. Luminaire and Driver both should be BIS approved and CRS no ( individual R no ) should be shared along with LM79 & LM80 during bid submission. Product should have Lifeclass of 50K hours @L70 with PF > 0.95 & THD ≤ 10%..product is designed to operate at (-10) Deg to45deg operating temp. 50,000 Hrs burning life is provided as per L70B50.

Sports Lighting SITC of 35W , Suspended / pendent mounted LED 1130mm Linar LED light. System output should not be more than 4000lm .System efficacy is 120lm/W. width of the product should be 50mm. Housing should be of CRCA powder coated with high Translucent Polystyrine Diffuser. Proposed CCT is 6500K along with CRI≥80.LM 80-08 compliant LEDs from reputed makes such asAPT Electronics / Cree, / Bridgelux / Lumiled should be provided. Product should have IP20 protection.LEDs used in the product shall comply with EN 62471 for Photo-biological safety and certificate for the same from manufacturer shall be provided.Driver shuld be DALI comptible. Driver is having p.f. ≥0.95 with iTHD≤10% Efficiency of driver shuld be minimum 90% with 4KV internal surge protection. Product is suitable to operate in 140 - 270V Ac range. Product should have inbuilt 4KV surge protection.. service life is 5000K as per L70B50.

SITC of Smart Panel with 63Amp 3 phase incomer and 2 outgoings of 32A 3Phase. Panel should have digital energy meter, control unit for monitoring and control, battery for control unit, SPD for control unit, CT, PT and current leak coil. Control unit should be compatible with 3phase and single phase power supply. It should be compatible for exchange of data through CAT6 cable or data sim card.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 2 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 3 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 4 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 6 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 8 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 12 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 16 / 18 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting modular type switch 6A / 10A duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type switch 16 / 20 A with indicator, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type 3 pin 6A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete.

Open To Sky Area Development-50 meter Range Building:- Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50

Supplying and erecting energy saving ceiling fa

n 230 V A.C. 50 cycles 1200 mm complete erected in position as per specification no. FG-FN/CF

Point wiring for light/bell/exhaust fan in 20 mm FRLS grade HMS PVC conduit with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification No: WGPW/ SW.

Point wiring for ceiling fan (Surface type under false ceiling and concealed type for drops & switch boards on walls) in min 20 mm PVC conduit / casing n capping with 1.5 sq.mm. (2+1E) FRLSH grade copper wires, modular type switch, earthing and required accessories as per specification No: WG-PW/HW

Supplying, erecting & marking SPMCB 6A to 32A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking SPMCB 6A to 32A, B-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking SPMCB 40A to 63A, B-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 3.00 m.) By Manual Means Spec. No.:- Bd.A.1 Page Number 259

Supplying, erecting & marking FPMCB 40A to 63A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying & erecting triple pole and neutral distribution board (TPNDB), SPMCB of 4 ways/phase (12 poles), with door, 1.2mm thickness, surface/flush mounted, IP 43 protection on iron/GI frame (horizontal busbar type) as per specification no. SW-SWR/MCBDB

Supplying & erecting triple pole and neutral distribution board (TPNDB), SPMCB of 8 ways / phase (24 poles), with door, 1.2mm thickness surface/ flush mounted, IP 43 Protection on iron/GI frame (horizontal busbar type) as per specification no. SW-SWR/MCBDB

Supplying and erecting single pole and neutral distribution board (SPNDB), with 2 ways for incoming and 10 ways (10 poles) for outgoing SP MCBs, with door, 1.2mm thickness surface / flush mounted, IP 43 Protection on iron / GI frame as per specification no. SW-SWR/MCBDB

Supplying and erecting fresh air cum exhaust fan of light duty 250 V A.C. 50 cycles 225mm. 1400 RPM rust proof body & blades, wire mesh, duly erected, complete.

Providing antitermite treatment to the for interior surfaces of floor, wall. Scope of Work •Making 3” wide x 9”deep trench along the wall & floor OR Drilling 12 mm diameter holes at the junction of Wall & Floor at 90° angle •Drilling 12 mm diameter holes, 12 inches deep at 1 feet distance C/C •Filling the holes with Termiticide Solution (1lit per hole) OR Applying Termiticide Solution @ 2.25 liter per linear meter in trenches •Filling the holes with cement mortar OR Filling the trenches with soil and treat the top surface with Termiticide Solution @ 1.0 ltr. Per linear meter •Customer is requested to put plinth protection complete covering 2 years guarantee on bond paper. Spec. No.:- As directed by Engineer in charge.

Providing & Fixing in position Acoustical Doors along with 150x150mm teak wood frame, doors made from 50mm Teak wood frame 600x600ctoc filled with 1000 Gsm synthetic wool 50mm thick and 3mm Tecsound from both sides,12mm waterproof ply & veneer from both sides, including 150mm heavy duty SShinges(Geze/Dormaoreq.)4no each leaf,withDoor-closer(Dorma/Gezeoreq.)including cost of required Cut-Outs,decorative mouldings/finishing-items/melamine polish & Scaffolding as per Architectural & Acoustical Design & Instructions & Complete in all aspects.including all materials labour,finishing etc complete

Wood Panel for Walls, Back Fire Panel Spectator and Target Area Providing & Fixing Imported PineWood 25 mm thick 4" width, both side chamfering, Front side machine grinding for smooth surface with water based painting (Apex) on both front and rear sides etc.

Providing & erecting hot dipped galvanised Perforated type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 300 mm width & 75 mm height complete with necessary coupler plates & hardware.

Supplying and erecting PVC box trunking of size 50x50 mm. with accessories on wall/ceiling as per specification No: WG-MA/BOX.

Supplying and erecting PVC box trunking of size 75x50 mm. with accessories on wall/ceiling as per specification No: WG-MA/BOX.

Supplying and erecting PVC box trunking of size 75x75 mm. with accessories on wall/ceiling as per specification No: WG-MA/BOX.

Supplying, erecting & commissioning 2 pole RCCB 16/25A, electromagnetic type with 30/100/300 mA sensitivity with earth leakage trip indication complete as per specification no. SW-RCCB/RCCB

Supplying, erecting & commissioning 2 pole RCCB 40A, electromagnetic type with 30/100/300 mA sensitivity with earth leakage trip indication complete as per specification no. SW-RCCB/RCCB

Supplying, erecting & commissioning 2 pole RCCB 63A, electromagnetic type with 30/100/300 mA sensitivity with earth leakage trip indication complete as per specification no. SW-RCCB/RCCB

Supplying, erecting & marking DPMCB 40A to 63A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying and erecting modular type switch 6A / 10A duly erected on provided plate and box with wiring connections complete.

m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 3.00 m.) By Manual Means Spec. No.:- Bd.A.1 Page Number 259

Providing and applying priming coat on concrete/ masonary/ Asbestos Cement plastered surfaces including scaffolding if necessary, preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and sand papering as required etc. complete.

Supplying & erecting CRCA sheet metal one way enclosures of 1.2mm thickness suitable for DP MCB /TP MCB/FP MCB/RCCB/RCBO complete erected on angle iron/GI frame.

Supplying & erecting CRCA sheet metal enclosures of 1.2mm thickness with 10A, 2 pin plug & earth socket and 10A, 3 pin plug top with 10A single pole MCB having rated short - circuit breaking capacity (Icn) 10kA complete erected on angle iron / GI frame.

Supplying & erecting CRCA sheet metal enclosures of 1.2mm thickness with 20A, 2 pin plug & earth socket and 20A, 3 pin plug top with 20A/30A single pole MCB having rated short - circuit breaking capacity (Icn) 10kA complete erected on angle iron/ GI frame.

Supplying & erecting CRCA sheet metal enclosures of 1.2mm thickness with 30 A, 3 pin plug & earth socket and 30A, 3 pin plug top with 30A triple pole MCB having rated short - circuit breaking capacity (Icn) 10kA complete erected on angle iron / GI frame.

Supplying and erecting HMS PVC conduit FRLS grade 32 mm dia. With PVC accessories on wall / ceiling as per specification No: WG-MA/CON.

Supplying and erecting electronic type step regulator for ceiling fan 600 / 900 / 1200/ 1400 mm. sweep, complete erected on provided switch board.

Supplying and erecting PVC insulated PVC round sheathed 2.5 sq.mm (50 no. x 0.25 mm dia.) 3 core flexible multi stranded copper Industrial cable for voltage grade up to 1.1 Kv

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 6 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL 8) For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 5 %

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 25 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL 8) For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 5 %

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 300 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL 8) For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 5 %

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3 core 4 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU 8) For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 5 %

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3 core 6 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per spec

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 4 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU 8) For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 5 %

itemH1Code119

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 6 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU 8) For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 5 %

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 10 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU 8) For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 5 %

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 16 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU 8) For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 5 %

Supplying & erecting triple pole and neutral distribution board (TPNDB), 3 pole/4 pole MCCB as incomer & outgoing SP MCB (36 poles) or TP MCB of 12 ways (36 poles), with door, 1.2mm thickness, surface/flush mounted, on iron/GI frame (vertical busbar type) as per specification no. SW-SWR/MCBDB1

Providing & erecting 3 Pole MCCB, 415V, 200A, rated short-circuit breaking capacity 25 kA (Ics=100% of Icu), adjustable thermal (overload) setting and adjustable magnetic setting with provided leads, provision for installation of shunt/UV/trip alarm contact and MCCB should have phase barriers both sides, with insulation withstand capacity 800V, no line-load bias in provided enclosure/panel as per specification no. SW-SWR/MCCB

Supplying and erecting terminal spreaders suitable for 3 pole, up to 250A MCCB (set of 6)

Supplying, erecting, testing and commissioning of 10kVA capacity online pure sine wave with backup time of 0.30 hrs. PWM & IGBT based UPS with 0.9 to unity output pf, 3 phase input & 1 phase output complete with all protections as per specification no. AP-UPS

DATA networking Supplying and installing cat-6 LSZH cable suitable for networking as peR specification no. WG-COC/NC

Supplying and fixing tool-less IO (Ethernet) flush/surface type in provided modular box as per specification no. WG-NAS/IO

Supplying, erecting & marking FPMCB 6A to 32A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 2 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting modular type blanking plate one module, duly erected on provided plate & box.

Supplying and fixing tool-less shutter keystone jack (RJ-45) in provided patch panel complete as per specification no. WG-NAS/KJ

Supplying and fixing 24 port patch panel with tool-less keystone jacks in provided U Rack complete as per specification no. WG-NAS/PP

Supplying and fixing 1 m length, UTP patch cord of enhanced Cat 6 type with 4-connector channel, performance test report as per ANSI/TIA-568.2-D in position as per specification No. WG-COC/PC

Supplying and fixing 3 m UTP patch cord of Cat 6 type in position as per specification No. WG-COC/PC

Supplying, installing, testing and commissioning of addressable fire isolator module complete as required. EN 54 /FM or UL Listed with 3 years equipment replacement warranty conforming to IS 5051Part 2 (Sec 1 to 3) : 1982 Reed relays FF-AFAS/ISM.

itemH1Code398

itemH1Code399

itemH1Code400

VOICE networking Supplying and erecting modular type telephone socket one gang with safety shutter, duly erected on provided plate and box with wiring connections complete.

Supplying, erecting & commissioning MDF Box 50x50 pairs made from min. 1.5mm thick MS sheet as per specification no. WG-TW

Supplying, erecting & commissioning MDF Box 100x100 pairs made from min. 1.5mm thick MS sheet as per specification no. WG-TW

Supplying & erecting co-axial copper cable low voltage grade tri-shielded RG- 6 as per specification No. WG-TW

Supplying & erecting co-axial copper cable low voltage grade tri-shielded RG- 11 as per specification No. WG-TW

Supplying and erecting modular type T.V. socket single outlet, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 1 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

itemH1Code401

Supplying, installing, testing and commissioning remote response indicators suitable to operate on 5 - 28 V dc supply having FR Polymer ABS Housing complete as per specification no. FF-FAAS/RRI

itemH1Code402

itemH1Code403

itemH1Code404

itemH1Code405

itemH1Code406

Supplying, installing, testing and commissioning of addressable fire control/ relay module complete as required, with 3 years equipment replacement warranty conforming to IS 5051Part 2 (Sec 1 to 3) : 1982 reed relays, EN 54 or UL Listed FF-AFAS/CRM.

Supplying, installing, testing and commissioning of addressable fire monitor module complete as required. EN 54 or UL Listed with 3 years equipment replacement warranty conforming to IS 5051Part 2 (Sec 1 to 3) : 1982 Reed relays FF-AFAS/MM.

itemH1Code407

itemH1Code402

itemH1Code408

FIRE ALARM SYSTEM EQUIPMENT Supplying, installing, testing and commissioning of micro processor based intelligent addressable main fire alarm panel, central processing unit with the 2 loop capacity and capable of supporting upto 250 devices and detectors per loop, with on-board LCD display with min 16 lines of text, operating at 230 V 50 HZ - AC with inbuilt Battery Backup of a minimum 24 hours in normal condition and 30 min in alarm condition, suitable provision for network connectivity, interfacing with third party equipment via a MODBUS/ OPC/ L-ON interface etc. conforming to IS 15908:2021, IS 2189: 2008, EN 54 & VDS / FM/ UL 864 (10th edition) with 3 years replacement warranty FF-AFAS/CP.

Supplying, installing, testing and commissioning of repeater panel with suitable battery backup of a minimum of 24 hours in normal condition and 30 min in alarm condition, 80 backlit alphanumeric LCD display with inbuilt buzzer to indicate fault/fire alarm, manual control keys for silence/mute and to reset the FACP from the repeater station. Panel size shall not more than 175 x 275 x 65 mm conforming to EN 54 or UL approved with 3 years equipment replacement warranty FF-AFAS/RP.

Supplying, installing, testing and commissioning of addressable fire isolator module complete as required. EN 54 /FM or UL Listed with 3 years equipment replacement warranty conforming to IS 5051Part 2 (Sec 1 to 3) : 1982 Reed relays FF-AFAS/ISM.

Supplying, installing, testing and commissioning of addressable optical smoke detector, single/twin LED’s with 360 degree view, suitable for low voltage 15 to 32 V DC two wires supply, in-built locking mechanism to check the removal and pilferage of the detector, in built isolation mode, start up current 300μA and alarm condition current shall be maximum 6.5 mA, operating temperature 0°C to 50°C, humidity 0-95% RH, IP 41, conforming to IS 2189: 2008, 11360_1985_Reff2020 EN 54 or UL Approved with 3 years equipment replacement warranty FFAFAS/ SD.

Supplying, installation, testing & commissioning of fire fighter telephone handset complete as required.

Supplying, installing, testing and commissioning FRLS, XLPE armoured cable 2 core 1.5 sq.mm. copper conductor complete erected on wall/ ceiling complete as per specification no. CB-LT/CU Note 1)For item no.13-9-10 to 13-9-13 increase rate by 2% for FRLS

Voice Evacuation System (Public Address System) Supplying, installation, testing & commissioning of 2 zone, voice alarm controller with USB, MP3 player (including 2 zone button paging station) with seamless integration facility with main fire arm panel for voice evacuation complete as required.

Supply, Installation, testing & Commissioning of Single Channel 500W (1X500W)Class-D Amplifier and can provide automatic re-settable overcurrent, overload, overheating, overvoltage, under-voltage and DC protection.

Supplying and erecting GI wire of high purity of required sizes used for earthing or any other purposes on wall with necessary G. I. Clamps fixed on wall/cable/ conduit with screws complete.

Supplying and fixing 32 U floor mount server Rack (Dimension-DxWxH - 800X1000x1620 mm) as per specification No. WG-NAS/RAK

Providing & erecting hot dipped galvanised ladder type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 150 mm width & 75 mm height complete with necessary coupler plates & hardware.

Providing & erecting hot dipped galvanised cover suitable for perforated type Cable tray manufactured from 18 SWG (1.2 mm thick) GI sheet of 150 mm width & 20 mm height complete with necessary hardware.

S/I/T/C of Emergency Manual Override 25 Watt Volume Control with conesealed Backbox and accessories etc.

Supplying, installation and testing of maintenance free earthing comprising of Electrode of 17.2 mm diameter Low Carbon Steel with 250 micron molecular copper bonded earthing rod of Length 3m along with 25 kg Carbon based environment friendly back fill ground enhancing compound required to fill up the excavated earth with required quantity complete, and recording the results Specification no.

EA-MOBI

Providing and back filling ground enhancing compound 25 kg bag complete.

Supplying and erecting copper strip of required size used for earthing on wall and/or any other purpose with necessary copper clamps fixed on wall painted with insulating and non-corrosive bond with required joints As per specification no. EA-EP.

Supplying and erecting GI strip of high purity required size used for earthing on wall and/or any other purpose with necessary GI clamps fixed on wall painted with bituminous paint with joints required. As per specification no EA-EP.

Electrical Work of Final Range building:- Supplying & laying HMS PVC conduit 20 mm dia. with necessary accessories in RCC work/false ceiling/false flooring as per specification No. WG-MA/CC.

EXTRA REFREGRENT PIPE (IF REQUIRED) Supplying & erecting soft drawn copper pipe suitable for refrigeration system having 22 SWG thickness and inner dia / size 12 mm complete.

Supplying & erecting soft drawn copper pipe suitable for refrigeration system having 22 SWG thickness and inner dia / size 16 mm complete.

Supplying & erecting soft drawn copper pipe suitable for refrigeration system having 22 SWG thickness and inner dia / size 32 mm complete.

Supplying & erecting soft drawn copper pipe suitable for refrigeration system having 22 SWG thickness and inner dia / size 42 mm Complete.

Rigid PVC Drain Piping with Insulation Supplying & erecting HMS PVC conduit 25 mm. dia. With necessary accessories in wall/floor with chiseling appropriately as per specification No: WG-MA/CC.

itemH1Code532

itemH1Code93

Removing doors and windows with frames and stacking the materials as directed with all leads, lifts etc. complete. Spec. No.:- As directed by Engineer in charge.

itemH1Code94

itemH1Code95

Removing teak wood trellies work with frame including stacking the materials as directed with all leads, lifts etc. complete.

itemH1Code353

Providing antitermite treatment to the wooden frames of doors/windows of the existing building as perI.S.6313(Part-III) bydrilling 6mm dia.holes at four corners on one side and four corners on other side at a down wardangle of about 45 degree at the junction of wood work and masonary and injecting 150ml.of chlorodane 5% W.C.and sealing by filling putty etc. complete covering 2 years guarantee on bond paper.

Providing internal cement plaster 12mm thick in single coat in cement mortar 1:4 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etc. complete. Spec. No.:- Bd. L.2 Page Number 368

Providing antitermite treatment to the sides of flooring of the existing building as per I.S. 6313 (Part-III) by punching holes 6mm dia. drilled at a distance of 30cm. centre to centre and injecting one percent of chlorodane emulsion concentrate at the rate of 50 ml per hole and sealing by filling putty etc. complete covering 2 years guarantee on bond paper. Spec. No.:- As directed by Engineer in charge.

itemH1Code226

Transportation of excavated & debris from site to disposing site (lead 3km)

itemH1Code227

Providing & Fixing in position Acoustical Doors along with 150x150mm teak wood frame, doors made from 50mm Teak wood frame 600x600ctoc filled with 1000 Gsm synthetic wool 50mm thick and 3mm Tecsound from both sides,12mm waterproof ply & veneer from both sides, including 150mm heavy duty SShinges (Geze /Dormaoreq.)4no each leaf, with Door-closer (Dorma/ Gezeoreq.) including cost of required Cut-Outs,decorative mouldings/ finishing-items/ melamine polish & Scaffolding as per Architectural & Acoustical Design & Instructions & Complete in all aspects.including all materials labour,finishing etc complete

Supply & installation of Anutone Salon Slats Surco made of pinewood E1 grade fiberboard, melamine/veneer laminated finish, groove perforated slats L16-2 - (2mm grooves @16mm pitch with 27% open area) / L32-2 - (2mm grooves @ 32mm centers with 15% open area) surface density 63g/m2,tongue-groove edge for a seamless look, 5-test fire retardant grade, size 128 x2440x16mm, volume density of base board 700Kg/m3, weight 9Kg/m2 (L16), 10.5Kg/m2 (L32), 11Kg/m2 (L64) installed by using Anutone Strut framework system. The Anutone Strut fram

Providing and applying priming coat on concrete/ masonar

ework system shall include Anutone Strut CC10 thickness 0.55mm, length 3600mm, knurled web 40mm, depth 10mm and equal flanges 15mm is fastened to the wall positioned vertically at every 600mm centres.Anutone Strut CC18,aluminium core cross channel, thickness 0.5mm, length 2400mm, web 15mm & 27mm, depth 18mm and flanges of 7mm with suitable edge & center brackets is then fixed perpendicular to the Strut CC10 with the help of fasteners at every 400mm centersAnutone Slats Surco Plus of size 128x 2440x16mm in then fixed perpendicular to Strut CC18 with suitable edge & centre brackets. Contractor to provide expansion joints of 3mm at every 4.88m length wise and 4.992m width wise. Note:-Wooden packing of appropriate thickness to be provided at rear of strut to bring finish inline with Subtex NRC finish. The system is backlined with Anutone SynthPF 10x10 adhered on wall with dab spots of Anutone stick S7 adhesive., including Anti Termite Treatement. Technical Parameters Product Picture • Fire (Class) – 1 & P • Acoustics – NRC 0.75( For L32 C40 Mounting)• Thermal conductivity (W/mk)– na• Climate (°C, RH) – 50, 70• Light reflectance (%) – 75 (Maple Arce)• Green (VOC, RC %) – E1, 25

Wood Panel for Walls, Back Fire Panel Spectator and Target Area :- Providing & Fixing Imported PineWood 25 mm thick 4" width, both side chamfering, Front side machine grinding for smooth surface with water based painting (Apex) on both front and rear sides etc.

itemH1Code542

itemH1Code119

itemH1Code120

itemH1Code121

itemH1Code231

itemH1Code123

Supplying & laying HMS PVC conduit 25 mm dia with necessary accessories in RCC work/false ceiling/false flooring as per specification No. WG-MA/CC.

itemH1Code232

Supplying and erecting mains with 2x4 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW

itemH1Code533

itemH1Code534

itemH1Code535

Supplying & erecting ready to use Retrofit T8 LED 18 / 20 tube light with polycarbonate body, heat sink, integrated HF electronic driver complete & compatible to T8 / T12 LED luminaire by disconnecting starter & ballast if necessary.

Supplying and erecting anodized aluminium corridor / passage light LED fitting (4 feet) Max. 22W with high transitivity diffuser with system lumens output of Min.2200 lumens , min. efficacy of 100 lumen/W, CRI>80, CCT upto 6000K, Beam Angle of 110 deg., Ripple<5%, THD<10%, p.f. >0.95, operating range of 200-270V, surge protection of 2 kV, Life class of 50,000 Hrs. at L70B50, including driver, with end caps on provided PVC Block / wooden board with 3 years warranty.

Sports Lighting SITC of Recessed monted 2'x2', 36W Recessed 2'X2' LED ceiling fixture with system outut≥4200lm. System efficacy is ≥120lm/W.product is with IP20 CRCA powder coated housing. Luminaire shall have satin finished translucence (HET) PC diffuser for Uniform illumination and wider light distribution. LM 80-08 compliant LEDs from reputed makes such as APT Electronics / Cree, / Bridgelux / Lumiled should be provided. LEDs used in the product shall comply with EN 62471 for Photo-biological safety and certificate for the same from manufacturer shall be provided. Luminaire shall use SMD type LED. The LED shall be compliant with LM80-08 standard with Useful L70 life of 50000 Hrs tested at maximum current. Proposed CCT s 6500K with CRI>80 & SDCM<5. Driver shuld be DALI comptible. Driver is having efficiency of minimum 85%. p.f. ≥0.95 & THD≤10%.Driver should have 4KV inbuit surge protection is g

iven. Driver should be able to operate at 140 V to 240 V AC supply.

Sports Lighting SITC of IP65 Syemmetric medium beam, 100W LED Floodlight luminaire with system efficacy of 110lm/W.system output should not be more than 11000lm for 100W. Power consumption of luminaire should not exceed 100W. CCT should be 5700K with CRI ≥ 70. The housing should be made of non-corrosive high-pressure die-cast aluminum to with stand extreme environments. It should have corrosion resistant powder coating to pass NSS of 500 Hrs. Product should be suitable for continuous operation (10-12 Hrs. per day). The Ingress protection should be minimum IP 66 with an IK rating of 08. Optical and control gear compartments shall be maintainable/replaceable without impacting the LED units. The access to the optical and the gear compartment should be separate.. The Luminaire should have a 4KV SPD duly bolted in the Luminaire .The luminaire should be of Class B Serviceability. The wattage of each LED should be greater than 1 watt and less than 3 Watt. Only high power Single white LED chip with ceramic based suitable for outdoor use is allowed. Multi Chip , array multi die , mid power ,Integrated arrays and COB’s are not permitted. The luminaire should be capable of withstanding voltage stress of 440V for 8 Hrs., should have an auto shutdown @ 325V and have an auto recovery feature. The Drivers should be with 0-10V dimable diver. Driver should have short circuit and open circuit protection. Luminaire and Driver both should be BIS approved and CRS no ( individual R no ) should be shared along with LM79 & LM80 during bid submission. Product should have Lifeclass of 50K hours @L70 with PF > 0.95 & THD ≤ 10%..product is designed to operate at (-10) Deg to45deg operating temp. 50,000 Hrs burning life is provided as per L70B50.

Sports Lighting SITC of 35W , Suspended / pendent mounted LED 1130mm Linar LED light. System output should not be more than 4000lm .System efficacy is 120lm/W. width of the product should be 50mm. Housing should be of CRCA powder coated with high Translucent Polystyrine Diffuser. Proposed CCT is 6500K along with CRI≥80.LM 80-08 compliant LEDs from reputed makes such asAPT Electronics / Cree, / Bridgelux / Lumiled should be provided. Product should have IP20 protection.LEDs used in the product shall comply with EN 62471 for Photo-biological safety and certificate for the same from manufacturer shall be provided.Driver shuld be DALI comptible. Driver is having p.f. ≥0.95 with iTHD≤10% Efficiency of driver shuld be minimum 90% with 4KV internal surge protection. Product is suitable to operate in 140 - 270V Ac range. Product should have inbuilt 4KV surge protection.. service life is 5000K as per L70B50.

SITC of Smart Panel with 63Amp 3 phase incomer and 2 outgoings of 32A 3Phase. Panel should have digital energy meter, control unit for monitoring and control, battery for control unit, SPD for control unit, CT, PT and current leak coil. Control unit should be compatible with 3phase and single phase power supply. It should be compatible for exchange of data through CAT6 cable or data sim card.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 2 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 3 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 4 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 6 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 8 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 12 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 16 / 18 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting modular type switch 6A / 10A duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type switch 16 / 20 A with indicator, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type 3 pin 6A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete.

Open To Sky Area Development-50 meter Range Building:- Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50

Supplying and erecting energy saving ceiling fa

n 230 V A.C. 50 cycles 1200 mm complete erected in position as per specification no. FG-FN/CF

Point wiring for light/bell/exhaust fan in 20 mm FRLS grade HMS PVC conduit with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification No: WGPW/ SW.

Point wiring for ceiling fan (Surface type under false ceiling and concealed type for drops & switch boards on walls) in min 20 mm PVC conduit / casing n capping with 1.5 sq.mm. (2+1E) FRLSH grade copper wires, modular type switch, earthing and required accessories as per specification No: WG-PW/HW

Supplying, erecting & marking SPMCB 6A to 32A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking SPMCB 6A to 32A, B-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking SPMCB 40A to 63A, B-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 3.00 m.) By Manual Means Spec. No.:- Bd.A.1 Page Number 259

Supplying, erecting & marking FPMCB 6A to 32A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking FPMCB 40A to 63A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying & erecting triple pole and neutral distribution board (TPNDB), SPMCB of 4 ways/phase (12 poles), with door, 1.2mm thickness, surface/flush mounted, IP 43 protection on iron/GI frame (horizontal busbar type) as per specification no. SW-SWR/MCBDB

Supplying & erecting triple pole and neutral distribution board (TPNDB), SPMCB of 8 ways / phase (24 poles), with door, 1.2mm thickness surface/ flush mounted, IP 43 Protection on iron/GI frame (horizontal busbar type) as per specification no. SW-SWR/MCBDB

Supplying and erecting single pole and neutral distribution board (SPNDB), with 2 ways for incoming and 10 ways (10 poles) for outgoing SP MCBs, with door, 1.2mm thickness surface / flush mounted, IP 43 Protection on iron / GI frame as per specification no. SW-SWR/MCBDB

Supplying and erecting fresh air cum exhaust fan of light duty 250 V A.C. 50 cycles 225mm. 1400 RPM rust proof body & blades, wire mesh, duly erected, complete.

Providing antitermite treatment to the for interior surfaces of floor, wall. Scope of Work •Making 3” wide x 9”deep trench along the wall & floor OR Drilling 12 mm diameter holes at the junction of Wall & Floor at 90° angle •Drilling 12 mm diameter holes, 12 inches deep at 1 feet distance C/C •Filling the holes with Termiticide Solution (1lit per hole) OR Applying Termiticide Solution @ 2.25 liter per linear meter in trenches •Filling the holes with cement mortar OR Filling the trenches with soil and treat the top surface with Termiticide Solution @ 1.0 ltr. Per linear meter •Customer is requested to put plinth protection complete covering 2 years guarantee on bond paper. Spec. No.:- As directed by Engineer in charge.

Providing & Fixing in position Acoustical Doors along with 150x150mm teak wood frame, doors made from 50mm Teak wood frame 600x600ctoc filled with 1000 Gsm synthetic wool 50mm thick and 3mm Tecsound from both sides,12mm waterproof ply & veneer from both sides, including 150mm heavy duty SShinges(Geze/Dormaoreq.)4no each leaf,withDoor-closer(Dorma/Gezeoreq.)including cost of required Cut-Outs,decorative mouldings/finishing-items/melamine polish & Scaffolding as per Architectural & Acoustical Design & Instructions & Complete in all aspects.including all materials labour,finishing etc complete

Wood Panel for Walls, Back Fire Panel Spectator and Target Area Providing & Fixing Imported PineWood 25 mm thick 4" width, both side chamfering, Front side machine grinding for smooth surface with water based painting (Apex) on both front and rear sides etc.

Providing & erecting hot dipped galvanised Perforated type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 300 mm width & 75 mm height complete with necessary coupler plates & hardware.

Supplying and erecting PVC box trunking of size 50x50 mm. with accessories on wall/ceiling as per specification No: WG-MA/BOX.

Supplying and erecting PVC box trunking of size 75x50 mm. with accessories on wall/ceiling as per specification No: WG-MA/BOX.

Supplying and erecting PVC box trunking of size 75x75 mm. with accessories on wall/ceiling as per specification No: WG-MA/BOX.

Supplying, erecting & commissioning 2 pole RCCB 16/25A, electromagnetic type with 30/100/300 mA sensitivity with earth leakage trip indication complete as per specification no. SW-RCCB/RCCB

Supplying, erecting & commissioning 2 pole RCCB 40A, electromagnetic type with 30/100/300 mA sensitivity with earth leakage trip indication complete as per specification no. SW-RCCB/RCCB

Supplying, erecting & commissioning 2 pole RCCB 63A, electromagnetic type with 30/100/300 mA sensitivity with earth leakage trip indication complete as per specification no. SW-RCCB/RCCB

Supplying, erecting & marking DPMCB 40A to 63A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying and erecting modular type switch 6A / 10A duly erected on provided plate and box with wiring connections complete.

m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 3.00 m.) By Manual Means Spec. No.:- Bd.A.1 Page Number 259

Providing and applying priming coat on concrete/ masonary/ Asbestos Cement plastered surfaces including scaffolding if necessary, preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and sand papering as required etc. complete.

Supplying & erecting CRCA sheet metal one way enclosures of 1.2mm thickness suitable for DP MCB /TP MCB/FP MCB/RCCB/RCBO complete erected on angle iron/GI frame.

Supplying & erecting CRCA sheet metal enclosures of 1.2mm thickness with 10A, 2 pin plug & earth socket and 10A, 3 pin plug top with 10A single pole MCB having rated short - circuit breaking capacity (Icn) 10kA complete erected on angle iron / GI frame.

Supplying & erecting CRCA sheet metal enclosures of 1.2mm thickness with 20A, 2 pin plug & earth socket and 20A, 3 pin plug top with 20A/30A single pole MCB having rated short - circuit breaking capacity (Icn) 10kA complete erected on angle iron/ GI frame.

Supplying & erecting CRCA sheet metal enclosures of 1.2mm thickness with 30 A, 3 pin plug & earth socket and 30A, 3 pin plug top with 30A triple pole MCB having rated short - circuit breaking capacity (Icn) 10kA complete erected on angle iron / GI frame.

Supplying and erecting HMS PVC conduit FRLS grade 32 mm dia. With PVC accessories on wall / ceiling as per specification No: WG-MA/CON.

Supplying and erecting electronic type step regulator for ceiling fan 600 / 900 / 1200/ 1400 mm. sweep, complete erected on provided switch board.

Supplying and erecting PVC insulated PVC round sheathed 2.5 sq.mm (50 no. x 0.25 mm dia.) 3 core flexible multi stranded copper Industrial cable for voltage grade up to 1.1 Kv

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 6 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL 8) For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 5 %

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 25 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL 8) For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 5 %

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 300 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL 8) For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 5 %

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3 core 4 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU 8) For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 5 %

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3 core 6 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per spec

ification no. CB-LT/CU 8) For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 5 %

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 4 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU 8) For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 5 %

itemH1Code119

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 6 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU 8) For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 5 %

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 10 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU 8) For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 5 %

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 16 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU 8) For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 5 %

Supplying & erecting triple pole and neutral distribution board (TPNDB), 3 pole/4 pole MCCB as incomer & outgoing SP MCB (36 poles) or TP MCB of 12 ways (36 poles), with door, 1.2mm thickness, surface/flush mounted, on iron/GI frame (vertical busbar type) as per specification no. SW-SWR/MCBDB1

Providing & erecting 3 Pole MCCB, 415V, 200A, rated short-circuit breaking capacity 25 kA (Ics=100% of Icu), adjustable thermal (overload) setting and adjustable magnetic setting with provided leads, provision for installation of shunt/UV/trip alarm contact and MCCB should have phase barriers both sides, with insulation withstand capacity 800V, no line-load bias in provided enclosure/panel as per specification no. SW-SWR/MCCB

Supplying and erecting terminal spreaders suitable for 3 pole, up to 250A MCCB (set of 6)

Supplying, erecting, testing and commissioning of 10kVA capacity online pure sine wave with backup time of 0.30 hrs. PWM & IGBT based UPS with 0.9 to unity output pf, 3 phase input & 1 phase output complete with all protections as per specification no. AP-UPS

DATA networking Supplying and installing cat-6 LSZH cable suitable for networking as peR specification no. WG-COC/NC

itemH1Code536

itemH1Code537

itemH1Code538

Supplying and fixing tool-less IO (Ethernet) flush/surface type in provided modular box as per specification no. WG-NAS/IO

Supplying, erecting & marking FPMCB 6A to 32A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

itemH1Code539

itemH1Code540

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 2 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting modular type blanking plate one module, duly erected on provided plate & box.

itemH1Code541

Supplying and fixing tool-less shutter keystone jack (RJ-45) in provided patch panel complete as per specification no. WG-NAS/KJ

Supplying and fixing 24 port patch panel with tool-less keystone jacks in provided U Rack complete as per specification no. WG-NAS/PP

Supplying and fixing 1 m length, UTP patch cord of enhanced Cat 6 type with 4-connector channel, performance test report as per ANSI/TIA-568.2-D in position as per specification No. WG-COC/PC

Supplying and fixing 3 m UTP patch cord of Cat 6 type in position as per specification No. WG-COC/PC

itemH1Code398

itemH1Code399

itemH1Code400

VOICE networking Supplying and erecting modular type telephone socket one gang with safety shutter, duly erected on provided plate and box with wiring connections complete.

Supplying, erecting & commissioning MDF Box 50x50 pairs made from min. 1.5mm thick MS sheet as per specification no. WG-TW

Supplying, erecting & commissioning MDF Box 100x100 pairs made from min. 1.5mm thick MS sheet as per specification no. WG-TW

Supplying & erecting co-axial copper cable low voltage grade tri-shielded RG- 6 as per specification No. WG-TW

Supplying & erecting co-axial copper cable low voltage grade tri-shielded RG- 11 as per specification No. WG-TW

Supplying and erecting modular type T.V. socket single outlet, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 1 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

itemH1Code401

Supplying, installing, testing and commissioning remote response indicators suitable to operate on 5 - 28 V dc supply having FR Polymer ABS Housing complete as per specification no. FF-FAAS/RRI

itemH1Code402

itemH1Code403

itemH1Code404

itemH1Code405

itemH1Code406

Supplying, installing, testing and commissioning of addressable fire control/ relay module complete as required, with 3 years equipment replacement warranty conforming to IS 5051Part 2 (Sec 1 to 3) : 1982 reed relays, EN 54 or UL Listed FF-AFAS/CRM.

Supplying, installing, testing and commissioning of addressable fire monitor module complete as required. EN 54 or UL Listed with 3 years equipment replacement warranty conforming to IS 5051Part 2 (Sec 1 to 3) : 1982 Reed relays FF-AFAS/MM.

itemH1Code407

itemH1Code402

itemH1Code408

FIRE ALARM SYSTEM EQUIPMENT Supplying, installing, testing and commissioning of micro processor based intelligent addressable main fire alarm panel, central processing unit with the 2 loop capacity and capable of supporting upto 250 devices and detectors per loop, with on-board LCD display with min 16 lines of text, operating at 230 V 50 HZ - AC with inbuilt Battery Backup of a minimum 24 hours in normal condition and 30 min in alarm condition, suitable provision for network connectivity, interfacing with third party equipment via a MODBUS/ OPC/ L-ON interface etc. conforming to IS 15908:2021, IS 2189: 2008, EN 54 & VDS / FM/ UL 864 (10th edition) with 3 years replacement warranty FF-AFAS/CP.

Supplying, installing, testing and commissioning of repeater panel with suitable battery backup of a minimum of 24 hours in normal condition and 30 min in alarm condition, 80 backlit alphanumeric LCD display with inbuilt buzzer to indicate fault/fire alarm, manual control keys for silence/mute and to reset the FACP from the repeater station. Panel size shall not more than 175 x 275 x 65 mm conforming to EN 54 or UL approved with 3 years equipment replacement warranty FF-AFAS/RP.

Supplying, installing, testing and commissioning of addressable fire isolator module complete as required. EN 54 /FM or UL Listed with 3 years equipment replacement warranty conforming to IS 5051Part 2 (Sec 1 to 3) : 1982 Reed relays FF-AFAS/ISM.

Supplying, installing, testing and commissioning of addressable optical smoke detector, single/twin LED’s with 360 degree view, suitable for low voltage 15 to 32 V DC two wires supply, in-built locking mechanism to check the removal and pilferage of the detector, in built isolation mode, start up current 300μA and alarm condition current shall be maximum 6.5 mA, operating temperature 0°C to 50°C, humidity 0-95% RH, IP 41, conforming to IS 2189: 2008, 11360_1985_Reff2020 EN 54 or UL Approved with 3 years equipment replacement warranty FFAFAS/ SD.

Supplying, installation, testing & commissioning of fire fighter telephone handset complete as required.

Supplying, installing, testing and commissioning FRLS, XLPE armoured cable 2 core 1.5 sq.mm. copper conductor complete erected on wall/ ceiling complete as per specification no. CB-LT/CU Note 1)For item no.13-9-10 to 13-9-13 increase rate by 2% for FRLS

Voice Evacuation System (Public Address System) Supplying, installation, testing & commissioning of 2 zone, voice alarm controller with USB, MP3 player (including 2 zone button paging station) with seamless integration facility with main fire arm panel for voice evacuation complete as required.

Supply, Installation, testing & Commissioning of Single Channel 500W (1X500W)Class-D Amplifier and can provide automatic re-settable overcurrent, overload, overheating, overvoltage, under-voltage and DC protection.

Supplying, installing

, testing and commissioning of addressable horn cum strobe sound/ hooter, output frequency 500 to 1000 Hz with dB as per Chart given in IS 15908:2021, with flashing at 1 Hz over the strobe’s entire operating voltage range EN 54, conforming to IS 2189: 2008, IS 15908:2021 standards with 3 years equipment replacement warranty FF-AFAS/SSH.

Supplying, installation, testing & commissioning of fire fighter telephone handset complete as required.

Supplying, installation, testing & commissioning of fire fighter phone. jack complete as required.

Supplying, erecting & marking FPMCB 40A to 63A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB (for outdoor Unit)

itemH1Code543

Interior Work & Acoustical refurbishment of 10 Meter Range Building:- Removing cement tiles, or marble or polished shahabad floor or dado without bed concrete including stacking the materials as directed with all leads, lifts etc. complete Spec. No.:- As directed by Engineer in charge.

Sports Lighting -SITC of Recessed monted 2'x2', 36W Recessed 2'X2' LED ceiling fixture with system outut≥4200lm. System efficacy is ≥120lm/W.product is with IP20 CRCA powder coated housing. Luminaire shall have satin finished translucence (HET) PC diffuser for Uniform illumination and wider light distribution. LM 80-08 compliant LEDs from reputed makes such as APT Electronics / Cree, / Bridgelux / Lumiled should be provided. LEDs used in the product shall comply with EN 62471 for Photo-biological safety and certificate for the same from manufacturer shall be provided. Luminaire shall use SMD type LED. The LED shall be compliant with LM80-08 standard with Useful L70 life of 50000 Hrs tested at maximum current. Proposed CCT s 6500K with CRI>80 & SDCM<5. Driver shuld be DALI comptible. Driver is having efficiency of minimum 85%. p.f. ≥0.95 & THD≤10%.Driver should have 4KV inbuit surge protection is given. Driver should be able to operate at 140 V to 240 V AC supply.

Sports Lighting -SITC of IP65 Syemmetric medium beam, 100W LED Floodlight luminaire with system efficacy of 110lm/W.system output should not be more than 11000lm for 100W. Power consumption of luminaire should not exceed 100W. CCT should be 5700K with CRI ≥ 70. The housing should be made of non-corrosive high-pressure die-cast aluminum to with stand extreme environments. It should have corrosion resistant powder coating to pass NSS of 500 Hrs. Product should be suitable for continuous operation (10-12 Hrs. per day). The Ingress protection should be minimum IP 66 with an IK rating of 08. Optical and control gear compartments shall be maintainable/replaceable without impacting the LED units. The access to the optical and the gear compartment should be separate.. The Luminaire should have a 4KV SPD duly bolted in the Luminaire .The luminaire should be of Class B Serviceability. The wattage of each LED should be greater than 1 watt and less than 3 Watt. Only high power Single white LED chip with ceramic based suitable for outdoor use is allowed. Multi Chip , array multi die , mid power ,Integrated arrays and COB’s are not permitted. The luminaire should be capable of withstanding voltage stress of 440V for 8 Hrs., should have an auto shutdown @ 325V and have an auto recovery feature. The Drivers should be with 0-10V dimable diver. Driver should have short circuit and open circuit protection. Luminaire and Driver both should be BIS approved and CRS no ( individual R no ) should be shared along with LM79 & LM80 during bid submission. Product should have Lifeclass of 50K hours @L70 with PF > 0.95 & THD ≤ 10%..product is designed to operate at (-10) Deg to45deg operating temp. 50,000 Hrs burning life is provided as per L70B50.

Sports Lighting -SITC of 35W , Suspended / pendent mounted LED 1130mm Linar LED light. System output should not be more than 4000lm .System efficacy is 120lm/W. width of the product should be 50mm. Housing should be of CRCA powder coated with high Translucent Polystyrine Diffuser. Proposed CCT is 6500K along with CRI≥80.LM 80-08 compliant LEDs from reputed makes such asAPT Electronics / Cree, / Bridgelux / Lumiled should be provided. Product should have IP20 protection.LEDs used in the product shall comply with EN 62471 for Photo-biological safety and certificate for the same from manufacturer shall be provided.Driver shuld be DALI comptible. Driver is having p.f. ≥0.95 with iTHD≤10% Efficiency of driver shuld be minimum 90% with 4KV internal surge protection. Product is suitable to operate in 140 - 270V Ac rang

e. Product should have inbuilt 4KV surge protection.. service life is 5000K as per L70B50.

Supplying, fixing, and configuring 48 Ports managed gigabit switch 10/100/1000 Mbps + 4 SFP ports erected in provided rack complete.

Supplying, fixing, and configuring 48 ports managed gigabit switch Layer 2 with 48 10/100/1000 Base-T ports management switch with 4 10GE SFP+ ports erected in provided rack complete.

Supplying, fixing, and configuring 8-ports managed gigabit, Layer-2 switch, 10/100/1000 base-T, POE smart switch plus 2 SFP erected in provided rack complete.

Supplying & erecting 20 pair telephone copper cable 0.5 mm dia. with high density polyethylene insulation, polyester taped, Nylon Rip Cord & grey colour sheathed with FR PVC, conforming to ITD specification S/WS 113C laid in provided PVC casing capping/conduit as per specification No. WG-TW

Supplying & erecting 50 pair telephone copper cable 0.5 mm dia. with higdensity polyethylene insulation, polyester taped, Nylon Rip Cord & grey colour sheathed with FR PVC, conforming to ITD specification S/WS 113C laid in provided PVC casing capping/conduit as per specification No. WG-TW

Supplying and installing, testing & commissioning of digital (hybrid) type EPABX of 6 x 32 extensions suitable upto 96 extensions complete. Note :- 1) Add Rs. 38159.00 for additional 16 extension card for digital (hybrid) type EPABX

Electrical Work of 10 Meter Range building:- Supplying & laying HMS PVC conduit 20 mm dia. with necessary accessories in RCC work/false ceiling/false flooring as per specification No. WG-MA/CC.

INDOOR UNIT Supply, installation, testing and commissioning of VRV / VRF based floor mount type package, room/indoor unit (IDU) having nominal cooling capacity of 16.0TR/6400CFM having EER as per BEE standards and specifications with evaporator fan with motor, copper tube aluminium fin evaporator coil, washable air filter, insulated drain tray, in built drain pump, expansion device, corded remote control with necessary controls and electrical terminal to receive power supply, etc. having anti-corrosive coating suitable for coastal area with decorative slim dimension suitable floor mounting arrangement, an electronic control console and any additional refrigerant and oil charge as per requirement during installation complete.

Supplying and installation of high pressure grade required size copper connection Y or T- Joints / refnet for liquid and suction line complete erected on wall/ceiling with supports/raceways, Nitrile rubber insulation, painting etc. with brazing and testing for leakages confirming the normal operation of the VRV / VRF air conditioning system.

Providing vaccumising the airconditioner system to 200 micron and charging with R410a refrigerant for AC unit.

Supply Installation Testing & commissioning AHU Controller / distribution kit of suitable capacity for connecting multi VRF ODU to AHU, with a) built in auto restart function, c) with necessary electrical wiring & remote controller.

REFREGRENT PIPE Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 15.9 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge (hard drawn copper pipe for liquid main line and for refrigerant) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating suitable for use with VRV / VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV / VRF air conditioning system.

Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 28.6 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge (hard drawn copper pipe for liquid main line and for refrigerant) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating suitable for use with VRV / VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV / VRF air conditioning system.

DRAIN PIPE Supplying and erecting 32/40 mm (ID/OD) Chlorinated polyvinyl chloride pipe (CPVC), thickness 3.8 mm conforming to IS 15778 (CTS Series) with necessary CPVC fittings and solvent cement for Solar Water Heater System as per specification No. ESD-HWP/CPVC

Supplying and erecting GI strip of high purity required size used for earthing on wall and/or any other purpose with necessary GI clamps fixed on wall painted with bituminous paint with joints required. As per specification no EA-EP.

Supplying and erecting 40/50 mm (ID/OD) Chlorinated polyvinyl chloride pipe (CPVC), thickness 3.8 mm conforming to IS 15778 (CTS Series) with necessary CPVC fittings and solvent cement for Solar Water Heater System as per specification No. ESD-HWP/CPVC

Supplying and erecting elastomeric nitrile rubber / foam tube type sleeves for over coating and insulating on provided PC / copper pipes having 9 mm thickness and inner diameter / sizes 32 mm for solar water heater system.

Supplying and erecting elastomeric nitrile rubber / foam tube type sleeves for over coating and insulating on provided PC / copper pipes having 9 mm thickness and inner diameter / sizes 42/50 mm for solar water heater system.

VENTILATION FAN Supplying and erecting exhaust fan heavy duty 230 V, A.C. 50 cycles 375/380mm. 900 RPM complete erected in position as per specification no. FG-FN/EXF (500cfm)

HVAC Work of 10 Meter Range building:- VRV SECTION OUTDOOR UNIT Supplying, erecting, testing and commissioning of 20HP, VRF/VRV air conditioning system outdoor unit (ODU) complies type-IV OEM standards working on HFC refrigerant R410A or other required/suitable green equivalent refrigerant, for minimum cooling capacity as delivering 100% capacity at 47° C, non stop cooling even at 56°C and coefficient of performance (COP) 3.00 to 4.00, modular type vertical hot air discharge suitable for longer piping range upto 1000 metre operation in cooling mode with inverter/digital VRF/VRV technology microprocessor based control compressor starter/control panel with scroll compressor, air cooled copper condenser coil of suitable shape for increasing maximum heat transfer area, rain protection cover, built in oil separator, accumulator and oil receiver, copper tube aluminium fin air cooled condenser, condenser fan with motor suitable for 415V±10%, 50 Hz, 3 phase power supply (all suitable for high ambient conditions), internal copper refrigerant piping, internal wiring and refrigerant, etc. all housed in powder coated weather proof cabinet complete.

LOW SIDE SECTION DUCTING Supplying and erecting GI sheet 0.8 mm (22 SWG) having zinc coating of 275 microns with galvanization process compliance to IS 2629:1985 to be used for fabrication of boxes panel boards etc. including cutting, bending, drilling, welding, riveting etc. and painting with one coat of red lead paint and 2 coats of enamel paint.

Supplying and erecting GI sheet 0.6 mm (24 SWG) having zinc coating of 275 microns with galvanization process compliance to IS 2629:1985 to be used for fabrication of boxes panel boards etc. including cutting, bending, drilling, welding, riveting etc. and painting with one coat of red lead paint and 2 coats of enamel paint.