CONSTRUCTION OF DAYCARE FACILITY AT IISER PUNE

Amount

EARTHWORK

Earth work in excavation by mechanical means (Hydraulic excavator ) / manual means over areas (exceeding 30cm in depth. 1.5m in width as well as 10 sum on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed.: All kinds of soil. Quoted rate shall be cost of necesary slope protection shoring struting etc required for deep excavation. Plan area of execvation within footing line shall be paid for measurments. Rate shall be including cost of labour material , GST, etc complete. Nothing extra shall be paid seperatly.

Earth work in excavation by mechanical means (Hydraulic excavator )/ manual means over areas (exceeding 30cm in depth. 1.5m in width as well as 10 sum on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed.: Ordinary rock .Quoted rate shall be cost of necesary slope protection shoring struting etc required for deep excavation. Plan area of execvation within footing line shall be paid for measurments.

Excavation work by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains not exceeding 1.5 m in width or 10 sum on plan including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50m.Quoted rate shall be cost of necesary slope protection shoring struting etc required for deep excavation. Plan area of execvation within footing line shall be paid for measurments.

Hard rock ( blasting prohibited).

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : Quoted rate shall be cost of necesary slope protection shoring struting etc required for deep excavation. Plan area of execvation within footing line shall be paid for measurments.

All kinds of soil

Pipes, cables etc.not exceeding 80mm dia

Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia.

Filling with available excavated earth within campus obtained from borrow pits or including available ordinary rock in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Extra for every additional lift of 1.50 m or part thereof in ( for taking out excavated earth / ordinary or hard rock beyond the depth of 1.50 m from Ground level )

All kinds of soil

Ordinary or Hard rock

Carriage of material by mechanical transport including loading, unloading and stacking / spreading / leveling lead upto 1 km beyond the initial lead of 50m.

Excavated top Earth

Excavated rock

Supplying and filling disintegrated rock of size not more than 100mm brought from out side in trenches, plinth, under floors and basement etc. in layers not exceeding 20cm in depth consolidating each deposited layer for the required proctor density by ramming, mechanical earth compactors and watering including all leads and lifts etc. as directed by the Engineer in charge. The rate shall includes the cost of the materials, labour and all the operations and nothing extra shall be payable.( The payment shall be made for the compacted thickness of filling based on the levels or actual depth of compacted filling at site.)

Carting of the debries , unusable earth/soil to within premises to the locations as approved by local authorities and as per the directions of Architect including spreading, compacting as per the local norms, all other incidental charges, & all necessary lead and lift complete. Note: (Contractor to pay fees for all statutory sanction, royalties and obtain NOC for any kind of disposal).

CEMENT CONCRETE & REINFORCED CEMENT CONCRETE WORKS

Providing and laying in position ready mixed concrete manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead upto 12kms having continuous agitated mixer, manufactured as per approved mix design of specified grade for cement concrete work including pumping of R.M.C. from transit mixer to site of laying,finishing, curing , excluding the cost of centering, shuttering including cost of admixtures in recommended proportions as per IS : 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. M-10 grade using 180 kg of OPC cement ( 53 Grade) per cum of concrete as per IS standard plus fly ash up to 20 % confirming to Grade I of IS 3812 (Part-I) with uniform blending with cement in accordance with clauses 5.2 and 5.2.1 of IS 456:2000 .

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level for 1:4:8 (1 Cement : 4 fine sand : 8 graded stone aggregate 40 mm nominal size)

Providing and fixing up to floor five level precast cement concrete string or lacing courses, copings, bed plates, anchor blocks, plain window sills, shelves, louvers, steps, stair cases, etc., including hoisting and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand), cost of required Centering complete.

1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20mm nominal size)

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5mm nominal size).

Applying a coat of residual petroleum bitumen of penetration 80/100 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm bed by dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth.

DESIGN MIX: Providing and laying in position ready mixed M-25 grade concrete for reinforced cement concrete work, using fly ash and cement content as per approved design mix, and manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work, including pumping of R.M.C. from transit mixer to site of laying, excluding the cost of centering, shuttering, finishing and reinforcement, including cost of admixtures in recommended proportions as per IS : 9103 to accelerate / retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. NOTE- (1) Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/ recoverable separately. (2) Fly ash conforming to grade I of IS 3812 (Part-1) only be used as part replacement of OPC as per IS : 456. Uniform blending with cement to be ensured in accordance with clauses 5.2 and 5.2.1 of IS:456 -2000 in the items of BMC and RMC.

Up to Plinth Level

above plinth level

Extra for providing richer mixes at all floor levels. Excess/less cement over the specified cement content used is payable /recoverable separately.Providing M-30 grade concrete instead of M-25 grade BMC/ RMC. (Note:- Cement content considered in M-30 is @ 340 kg/cum)

Supplying and applying pre tested and approved water based concrete curing compound to concrete/ masonry surface, all as per manufacturer’s specification and direction of Engineer-in-charge.Non pigmented wet curing compound .

Centering and shuttering including strutting, propping etc. and removal of form for removal of form for:

Foundations, footings, bases of columns etc. for mass concrete.

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Suspended floors, roofs, landings, balconies and access platform.

Extra for shuttering in circular work in beams, columns.

Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Columns, Pillars, Piers, Abutments, Posts and Struts

Stairs, (excluding landings) except spiral-staircases.

Vertical and horizontal fins individually or forming box louvers band, facias and eaves boards.

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. Upto plinth level.

Thermo - Mechanically treated bars Fe 500

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. Above plinth level.

Thermo - Mechanically treated bars Fe 500

MASONRY WORKS

Brick work with FPS bricks of class designation 35 in superstructure above plinth level upto floor V level in all shapes and sizes in Cement mortar 1:6 (1 cement : 6 coarse sand) with PPC 43 grade cement having Fly ash content not less than 30%.

Brick work with modular fly ash lime bricks (FALG Bricks) conforming to IS:12894-2002, class designation 60 average compressive strength in Sub and super structure, above and below plinth level up to floor V level in :

Sub structure, below plinth level :Cement mortar 1:6 (1 cement : 6 coarse sand) with PPC 43 grade cement having Fly ash content not less than 30%.

Super structure, above plinth level upto Floor V level :Cement mortar 1:6 (1 cement : 6 coarse sand) with PPC 43 grade cement having Fly ash content not less than 30%.

WOOD WORK

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position Second class teak wood including two coats of black bitumastic paint two coats. ( Frame size to be vary from 2" to 4".)

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand :6 graded stone aggregate 20mm nominal size)

KITCHEN CABINATE WORKS

Providing and fixing cup board shutters , doors , shelves , drawers in 18 mm thick, with Pre-laminated flat pressed BWP grade plywood, having one side decorative lamination and other side balancing lamination, including IInd class teak wood lipping of 25 mm wide x12 mm thick with with gloss polishing necessary screws and bright finished stainless steel soft closing hinges, complete as per direction of the Engineer-in-Charge. Thickness of decorative laminate shall be 1mm and balancing laminate 0.8mm thickness, factory laminated , factory pressed. Actual one side area of plywood with laminate work shall be measured for payments.

Providing and fixing cup board shutters , doors , shelves , drawers in 12 mm thick, with Pre-laminated flat pressed BWP grade plywood, having one side decorative lamination and other side balancing lamination, including IInd class teak wood lipping of 25 mm wide x12 mm thick with necessary with gloss polishing screws and bright finished stainless steel soft closing hinges, complete as per direction of the Engineer-in-Charge.Thickness of decorative laminate shall be 1mm and balancing laminate 0.8mm thickness, factory laminated , factory pressed. Actual one side area of plywood with laminate work shall be measured for payments.

Providing ,fixing and integration of Stainless Steel SS304 grade factory made Kitchen basket/Cabinate/sliding trolies with wood work etc as per approved drawing

Providing , fixing and integration of SS304 long body recessed handles of 150mm size to kitchen cabinates. Hafle/Dorma/Hettich

Providing and fixing sliding track for drawers of kitchen cabinates of load capacity of 300Kg each pair as per approved drawing.

Providing and inserting with float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm) in kitchen cabinates with approved colour and design.Including alround beading.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) or epoxy base adesiveand silicon sealant, joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete with drip groove. at all levels.Granite of any colour and shade , Area of slab over 0.50 sqm.

FLUSH DOORS

Providing and fixing factory made laminated flush door shutter made of ISI marked flush door shutters of required thickness as given below excluding thickness of laminate, non–decorative type, core of block board /souerland core filling construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters having 1.5 mm thick decorative type laminates in mat finish, colour, shade, print approved by Engineer in charge on both faces of shutter fixed with phenol formaldehyde synthetic resin type adhessive conforming to IS 848

Including providing external lipping with 2nd class teak wood battens 32 mm x 6 mm on all edges of shutters and polishing the three exposed faces of lipping with melamine polish in approvd shade including fixing shutters with required number of ISI marked stainless steel butt hinge of 100 x 58 x 1.9 mm with stainless steel screw etc complete as per direction of Engineer in charge. The quoted rate shall includes the supplying and fixing of hard wares as listed below for each category of door, glazing and vision panel of mentioned sizes etc.and but not restricted.

Main Door MD - 40 mm thick , 2900 X 2400mm ( Two Panel door of 1800 X 2400mm and Semiglazed Fixed Panel of 450mm X 2400mm on either sides. ) Two Level door , Lower Level panel shall be 1200mm height , Upper panel shall be 1200 height. All four panels shall operate independetly , interlocked at door joint with teakwood edge leaping alround both layered panels incluuding between top and bottom panel. All as shown on drawing. List of hardwares per door as mentioned below i) 5 mm thick toughened glass of size 300 x 600 - 2 no ii) Mortice lock with Euro profile cylinder,shall be tested to 500000 operation cycles, with double throw deadbolt,to comply with Pr EN12209 -1 and BS 5872:1980 standards. Options like cylinder &turn,double cylinder, single cylinder, privacy cylinder shall be made available - 2 Nos iv) D Handle of 300mm height - 4 Pairs , SS304 make Shall be tested for corrosion resistence in accoradance with AS 2331.3.1Neutral salt spray test v) Floor stop SS 304 finish - 2 No vi) Hinges SS 304 Ball bearing Button tipped 102 x 76 x 3mm - 12 Nos vi) Tower bolt 150mm size - 4 Nos

Activity Room and Dining Room Door D1 - 38 mm thick , 1500 X 2400mm ( Double Panel door, two level door of 1500 X 2400mm with glazing and Two Level door , Lower Level panel shall be 1200mm height , Upper panel shall be 1200 height. All two panels shall operate independetly , interlocked at frame with List of hardwares per door as mentioned below i) 6 mm thick toughened glass of size 300 x 600 - 4 no ii) Mortice lock with Euro profile cylinder,shall be tested to 500000 operation cycles, with double throw deadbolt,to comply with Pr EN12209 -1 and BS 5872:1980 standards. Options like cylinder &turn,double cylinder, single cylinder, privacy cylinder shall be made available- 2 Nos iv) D Handle of 300mm height - 4 Pairs , SS304 make Shall be tested for corrosion resistence in accoradance with AS 2331.3.1Neutral salt spray test v) Floor stop SS 304 finish - 2 No vi) Hinges SS 304 Ball bearing Button tipped 102 x 76 x 3mm - 12 Nos vi) Tower bolt 150mm size - 4 Nos

CORRIDOR DOOR AT LIBRARY D2 - 38 mm thick , 1400 X 2400mm ( Double Panel door, two level door of 1400 X 2400mm with glazing and Two Level door , Lower Level panel shall be 1200mm height , Upper panel shall be 1200 height. All two panels shall operate independetly , interlocked for locking with List of hardwares per door as mentioned below i) 6 mm thick toughened glass of size 300 x 600 - 4 no ii) Mortice lock with Euro profile cylinder,shall be tested to 500000 operation cycles, with double throw deadbolt,to comply with Pr EN12209 -1 and BS 5872:1980 standards. Options like cylinder &turn,double cylinder, single cylinder, privacy cylinder shall be made available- 2 Nos iv) D Handle of 300mm height - 4 Pairs , SS304 make Shall be tested for corrosion resistence in accoradance with AS 2331.3.1Neutral salt spray test v) Floor stop SS 304 finish - 2 No vi) Hinges SS 304 Ball bearing Button tipped 102 x 76 x 3mm - 12 Nos vi) Tower bolt 150mm size - 4 Nos

NAP Rooms, office Door D3 - 38 mm thick , 1000 X 2400mm ( SINGLE Panel door, two level door of 1000 X 2400mm with glazing and Two Level door , Lower Level panel shall be 1200mm height , Upper panel shall be 1200 height. All two panels shall operate independetly , interlocked for locking with List of hardwares per door as mentioned below i) 6 mm thick toughened glass of size 300 x 300 - 8 no ii) Mortice lock with Euro profile cylinder,shall be tested to 500000 operation cycles, with double throw deadbolt,to comply with Pr EN12209 -1 and BS 5872:1980 standards. Options like cylinder &turn,double cylinder, single cylinder, privacy cylinder shall be made available- 1 No iv) D Handle of 300mm height - 2 Pairs , SS304 make Shall be tested for corrosion resistence in accoradance with AS 2331.3.1Neutral salt spray test v) Floor stop SS 304 finish - 1 No vi) Hinges SS 304 Ball bearing Button tipped 102 x 76 x 3mm - 6 Nos vi) Tower bolt 150mm size - 2 Nos

KITCHEN , LIBRARY , FEEDING ROOM , SICK ROOM , GYM Door D4 - 38 mm thick , 1000 X 2400mm ( SINGLE Panel door, Single level door with interlocked for locking with List of hardwares per door as mentioned below i) 6 mm thick toughened glass of size 300 x 300 - 4 no ii) Mortice lock with Euro profile cylinder,shall be tested to 500000 operation cycles, with double throw deadbolt,to comply with Pr EN12209 -1 and BS 5872:1980 standards. Options like cylinder &turn,double cylinder, single cylinder, privacy cylinder shall be made available- 1 No iv) D Handle of 300mm height - 2 Pairs , SS304 make Shall be tested for corrosion resistence in accoradance with AS 2331.3.1Neutral salt spray test v) Floor stop SS 304 finish - 1 No vi) Hinges SS 304 Ball bearing Button tipped 102 x 76 x 3mm - 5 Nos vi) Tower bolt 150mm size - 1 Nos

KITCHEN EXTERNAL DOOR , STORE ROOM DOOR , LAUNDRRY INTERNAL AND EXTERNAL DOOR , STAFF TOILET SIDE EXTERNAL DOOR , D4 - 38 mm thick , 1000 X 2400mm ( SINGLE Panel door, Single level door with interlocked for locking with List of hardwares per door as mentioned below i) 6 mm thick toughened glass of size 300 x 300 - Nil ii) Mortice lock with Euro profile cylinder,shall be tested to 500000 operation cycles, with double throw deadbolt,to comply with Pr EN12209 -1 and BS 5872:1980 standards. Options like cylinder &turn,double cylinder, single cylinder, privacy cylinder shall be made available- 1 No iv) D Handle of 300mm height - 1 Pair , SS304 make Shall be tested for corrosion resistence in accoradance with AS 2331.3.1Neutral salt spray test v) Floor stop SS 304 finish - 1 No vi) Hinges SS 304 Ball bearing Button tipped 102 x 76 x 3mm - 5 Nos vi) Tower bolt 150mm size - 1 Nos

TOILET DOORS : 30 mm thick theme series PVC flush door shutter in different plain and wood finish/ graphic finish made with fire retardant grade unsaturated polyester resin, all around ms box frame for support , core filled with water proof material with suitable steel framework inside at required places for fixing of fittings and casted monolithically with testing parameters of PVC door. Theme shall got approved from engineer In-charge, before printing. Door shall be waterproof. Approved Make Eureka / Greenlam / Swastik. Quoted rate shall be including cost of fixing , labour, material , GST, lead , Lift , etc complete. Nothing extra shall be paid separately. 1) Baby latch ( inside & out side ) - 2 No 2) SS 304 handle - 1no 3. Aluminium Louver grill 300 X 450mm - 1 nos 4. 4. 6 mm thick toughened glass of size 300 x 300 - 4 Nos , Floor stop SS 304 finish - 1 No vi) Hinges SS 304 Ball bearing Button tipped 102 x 76 x 3mm - 5 Nos

Providing and fixing grilled Safety door made-up of structural mild steel frame and cut flat design of approved size and shape. Outer door frame shall be fixed with anchor fastners. Quoted rate shall be including cost of aldrop, mortice lock,tower bolt , mosquito net etc complete. Nothing extra shall be paid seperatly.

ALUMINIUM WORKS

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC / neoprene felt etc. Aluminium sections shall be smooth,rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and paneling to be paid for separately) :

For fixed portion

Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of PVC / neoprene gasket required (Fittings shall be paid for separately).

Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVC/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-incharge . (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm) For Windows Colour : Mint Green

With toughned glass panes of 10.00 mm thickness for GlassPartitions

Providing & fixing sun control films of Garware or equivalent make to the specified window panels complete including cost of removing exsiting fade film from glass surface as per direction of engineer-in-charge. Net area fixed at site shall be measured for payment.

Providing and fixing Eliptical hollow louver ( 70 x 11 x 1.5thk ) louver blades having 1.5 mm thick and to profile and shape as per drawing. The louver blades to be set in aluminium box frame plate of size 44.5 x 3.62 x 3 mm - section no. 4153 - weight not less than 0.211 Kg/m and this plate shall be fixed in to the outer box frame alround of size 62.50 x 37.10 mm - 1.50mm - section no. 9238 and weight not less than 0.855 Kg/m. The louver shall be fixed on to the aluminium box frame as per approved drawings including fixing the Box frame into wall/RC surface using SS anchor fasteners of Hilti make or approved equivalent.

Providing and fixing of following Alu. Window fittings of DORMA make / Geze or approved equivalent with necessary screws, fixtures etc.all complete as per direction of Engineer in charge

Star Lock big Powder coated / Metal finish

Sliding wheel

Providing and fixing stainless steel flyproof mesh S.S. wire gauze to windows using S.S-304 wire mesh with average width of aperture 1.4 mm in both directions with wire of dia. 0.63 mm .

Extra for openable side / top hung vision glass panels (SGUs) including providing and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min four -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineerin-Charge. ( Heavy duty stainless steel friction hinges pair shall be measured for payments , Cost of glass and aluminum to be measured seperatly in concern item )

STEEL WORKS FOR SKY ROOFING

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works ,Sky roof closiing

Providing, structural designing as per IS codes, drawings, manufacturing in approved pre engineering factory, hoisting, erection and fixing in position, pre engineered structural steel supporting main frame work in built-up sections, cutting, welding drilling holes, as per approved structural design and drawings / hot rolled steel box sections supporting main members bent to required shape as per structural design, with connecting plates/base plates, submerged arc welding, all lead and lifts ceiling height up to 25 m from building plinth level including mechanical hoisting , lifting , shifting , postioning etc complete.

Providing and fixing the anchoring/holding down bolts of HILTI make as per structural design requirements on exiting RCC column/beams/ Brackets / Clamps including fastening straps, nuts, bolts, rivets, washers etc. as per design requirement and as per approved shop drawing. Brackets / Clamps shall be of hot dip galvanized steel and Fastening materials shall be Non - magnetic Stainless steel 300 series - 316 grade of Hilti make or approved equivalent. Galvanizing thickness shall be in accordance with IS 2629 and 4759. Providing and fixing Serrated plates or Serrated washer wherever required as per the system requirement and as shown in the approved shop drawing complete as per direction of Engineer in charge. Structural steel design shall be got approved from IIT or COEP.

Mode of measurements: Actual weight of structural steel fixed at site excluding the weight of holding down bolts shall be measured for payment. Quoted rate shall include the cost of all materials, labour, cost of holding down bolts, fasteners, nits & bolts, all operations and process specified above, all wastages, steel scaffolding, infrastructure facility, tools and plants, all taxes, central excise & other levies, Octroi/LBT, GST , execution of work at ceiling height up to 25 m from plinth level of the building, all leads and lifts, all cost towards structural design & drawings, proof checking of structural design, all approvals, testing, etc. complete. Quoted rate shall also include the cost of providing and applying Zinc Phosphate primer before and after erection with minimum 75 microns and top coat with Low VOC Epoxy or Polyurethane paint with minimum 150 to 175 microns (DFT) of approved colour for all structural steel members.

Design, drawings, providing & fixing structural closing system with 16 mm thick 5 layer Multiwall-Multicell polycarbonate sheet plain clear UV coated polycarbonate sheet of approved make panels, cut to required size with required fittings and fixture, gutters, gaskets, aluminium beading , sealants as per approved design and drawings. Conducting the test for the materials involved in the system, field test on the erected system at site as per the test criteria set out in the specification of External glass ceiling/roofing / Facade structural glazing system. Submission of methodology for the Materials and assembly - field test supported by the copy of relevant codes & Standards and the same shall be got approved from IISER Pune prior to testing. Approved Make DANPALON , COLOUR SHADE-ICE

Providing and fixing Eliptical hollow louver as per architetural drawing louver blades having 1.5 mm thick and to profile and shape as per drawing. The louver blades to be set in aluminium box frame plate of size 44.5 x 3.62 x 3 mm - section no. 4153 - weight not less than 0.211 Kg/m and this plate shall be fixed in to the outer box frame alround of size 62.50 x 37.10 mm - 1.50mm - section no. 9238 and weight not less than 0.855 Kg/m. The louver shall be fixed on to the aluminium box frame as per approved drawings including fixing the Box frame into wall/RC surface using SS anchor fasteners of Hilti make or approved equivalent.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment).

FLOORING WORKS

For Potwash area : 52 mm thick cement concrete flooring with concrete hardener topping under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume .hardening compound is mixed @ 2 litre per 50kg of cement or as per manufacturers specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

Extra for making chequers of approved pattern on cement concrete floors, steps, landing, pavements etc.

Providing and laying Italian shade/Digital Series Glazed Ceramic floor tiles of 300X300 / 300 x 450 / 600 X 300 / 600X600 any size availble with manufacture or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours,size and shades, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete. Agency shall provide tiles as approved by Engineer Incharge within any digital or italian series of approved makes. Quoted rate shall be including taxes , duties , labour , manpower , GST .Nothing extra shall be paid separately. Approved Makes Nitco / Kajaria / Johnson / RAK. Actual area of tiling fixed at site shall be measured for payments.

Providing and fixing Italian shade/Digital Series pattern ceramic/engineered glazed wall tiles of 300X300 / 300 x 450 / 600 X 300 / 600X600 any conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade etc complete. Quoted rate shall be including cost of highlighter band ,Engineer Incharge shall shortlist tiles within any series of approved makes. Quoted rate shall be including taxes , duties , labour , manpower , GST .Nothing extra shall be paid seperatly.Approved Makes Nitco / Kajaria / Johnson / RAK.Actual area of tiling fixed at site shall be measured for payments. For Toilet and Kitchen

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye , Ruby Red , Multicolour or equivalent.

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : 11.55.1 Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Granite of any colour and shade Area of slab upto 0.50 sqm

Extra for providing edge moulding to 18mm thick Granite stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.

FINISHING WORKS

Internal Plastering of internal wall 12mm cement plaster of mix 1:4 (1 cement : 4 fine sand) with PPC cement having Fly ash content not less than 30% including scaffolding etc.

Plastering of External wall 18mm cement plaster in two coats under layer 12mm thick cement plaster 1:5 (1 cement : 5 coarse sand) finished with a top layer 6mm thick cement plaster 1:3 (1 cement : 3 coarse sand) finished rough with sponge, with PPC cement having Fly ash content not less than 30% including required scafolding etc complete.

Plastering of ceiling or RCC members in 6 mm cement plaster of mix : 1 : 3 ( 1 cement : 3 fine sand ) with PPC cement having Fly ash content not less than 30%.

Extra for providing and fixing of GI Chicken mesh at junction of RCC and masonry works. The mesh should be in double folded of 15cm width fixed in to the Masonry / RCC by using rawl plugs at the location as directed by the engineer in charge. The quoted rate inclusive of all materials, tools, tackles at all levels and height etc.

Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers.min 2% by weight of cement to be considered .

Extra for plastering on circular work not exceeding 6 m in radius:

Providing and applying white cement based putty of average thickness 2mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.Quoted rate shall be including at taxes , duties , royalties , lead, lift , trasportation , insurance , GST , etc. Nothing extra shall be paid seperatly. Approved Makes Nerolac/Dulux/Asian.Actual area of painting at site shall be measured for payments.

Providing and applying Weather proof texture finish external painting from the approved agencies as per approved design and pattern, texture finish shall be applied over the plasterd surface with minimum 2mm thickness to form the necessry patterns of designs by using trowel /putty blade and it should be allowed for drying minimum 12 hrs before the application of top painting. Top coat shall be 2 coats of external weather proof paint shall be applied over the texture base and a coat of primer may be applied based on the approved texture pattern and as per manufacturer's specifications of approved makes etc complete. Including surface preparation like through cleaning, prewetting & removal of loose motars etc .The quoted rate shall includes the cost for all the above items including labours, tools,scaffolding & tackles for at all heights etc. Mode of measurement :measured and paid same as per plastering workings. Approved make Asian Ultima Allura Venezio /Dulux/Burger

Providing and applying Luster paint of Asian/ Nerolac/Berger of low VOC as per manufacturers specifications of including one coat of approved primer on wall / ceiling with roller finish including preparation of surface by sand papering so as have and even and smooth surface. Quoted rate shall be including smoothing sanding, scaffolding , primer , filling of cracks , all leads and lift, labour , cleaning and cost of all materials etc complete as per direction of Engineer-in-charge. (Nothing extra shall be paid seperatly) : Two or more coats.Actual area of painting at site shall be measured for payments.( Internal walls )

Washed marble stone grit plaster on exterior walls of height at all level in two layers, under layer 12mm cement plaster 1:4 (1cement 4coarse sand ) furrowing the under layer with scratching tool, applyingcement slurry on the under layer @ 2 Kg of cement per square metre,top layer 15mm white cement plaster 3:1:6 (3 white cement: 1marble powder : 6 marble chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the marble stone chippings, complete as per manufacturer's specifications of approved makes, including necessary scaffolding etc complete, and as direction of Engineer-in- charge (Payment for providing grooves shall be made separately).

Forming groove at all height at all level of uniform size in the top layer of washed grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and & including necessary scaffolding etc complete and as direction of the Engineer-in-charge :

15 mm wide and 15 mm deep groove

Distembering with oil bound washable distemper of approved brand and manufacture to give an even shade

New work (two or more coats) over and including priming coat with cement primer. ( Ceiling )

Providing & applying Premium Texure paint on walls of Royal Play Asian/ Nerolac/Berger of of approved pattern as per manufacturers specifications of including one coat of approved primer on wall with roller finish including preparation of surface by sand papering and applying two coats of 2 mm thick Birla/Altek wall care putty on complete surface so as have and even and smooth surface. Quoted rate shall be including smoothing sanding, scaffolding , primer , putty , filling of cracks ,tools for texure , painting of texure surfce , all leads and lift, labour , cleaning and cost of all materials etc complete as per direction of Engineer-in-charge. (Nothing extra shall be paid seperatly) : Two or more coats including creating texure of approved pattern.Actual area of painting at site shall be measured for payments.

WATER PROOFING WORKS

Terrace Water proofing : Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: a) Applying a slurry coat of neat cement using 2.75 kg/sqm. of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300mm height including cleaning the surface before treatment. b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs

c) After two days of proper curing applying a second coat of cement slurry using 2.75kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3mm deep.

e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineer-in-Charge. With average thickness of 120mm and minimum thickness at khurra as 65 mm.

For Toilets at GF : Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate and waterproofing compound. sqm 498.35

MISCELLANEOUS WORKS

Making plinth protection 40 mm thick rubbed stone flooring over 20 mm (average) thick base of cement mortar 1:5 (1 cement :5 coarse sand) with joints 3mm thick,side buttered with cement mortar 1:2 (1 cement : 2 stone dust) admixed with pigment to match the shade of stone and pointing with same mortar.Red sand stone of single stone slab size not less than 0.60 sqm

Making hole for rebar in concrete / masonry surface to any dia and depth as required @ site by using HILTI make driller with HY150 chemical compound for inserting the reinforcement after drilling and air jet. Cleaning etc complete, at any level, etc complete. Rate shall include for all charges and preparation of surface, cutting of reinforcement cleaning the surface, staging, scaffolding and working platform, application of necessary chemical / foil as per manufactures specification with necessary tools and equipments, water and power, removal of debris from the site, tax component etc complete, as directed.

8 / 10 / 12 MM Dia - Rebar for the depth vary from 100 mm to 120 mm

16 / 20 / 25 MM Dia - Rebar for the depth vary from 150mm to 200 mm

Providing and fixing Polyvinyl Chloride (PVC-SWR grade) pipes concealed /open type for SWR line , including all fittings, including fixing the pipe with GI clamps at 1.00 m spacing for good support to pipe , perfect slope towards header line etc complete. Item includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Concealed type . All chases shall be suitably deep with nail support and mortar finishing. Quoted rate shall be including material , labour , transportation , lead , lift , Bends , coupler , cleanouts , tees , solvent cement , make holes in wall and making it good , GST etc complete. Nothing extra shall be paid separately. Length of pipe laid at site shall be measured for payments. Approved Make : Finolex/Supreme/Astral/Watertec Piping including bends , tees solvent 110 mm dia

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 300 mm dia. R.C.C. pipe.

Providing & fixing 6mm thk. first quality modiguard mirror or equivalent as approved by Engineer In-charge make with 25mm SS stud including crystal edge polishing on all edges to have smooth with 8mm plywood backing and etc.complete. Quoted rate shall be including taxes , duties , material , labour , tools , scaffolding, lead , lift , trasportation etc complete. Nothing extra shall be paid seperatly.Actual commissioned article at site shall be measured for payments.

Providing and fixing of 8mm thick lacquered glass of approved colour and pattern from Saint Gobain or equivalent make over the existing wall surfaces including 5mm wide Philphs/Syska full length all around glass LED backlight strip with necessary hardware , driver , cabling etc complete. The rate shall be inclusive of necessary SS Stud, hardware and wastage etc; complete.

Demolision of RCC road for pipe crossing - Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Shifting of DI lines by removing existing lines and relaying as per new layout including cost of supply of new pipes. Cost of new pipes laid shall be measured for payments. Existing pipes shall be laid without additional cost, Providing push-on-joints to Centrifugally (Spun) Cast Iron Pipes or Ductile Iron Pipes including testing of joints and the cost of rubber gasket : 18.72.1 100 mm dia Ductile Iron Class K-7 pipes.

Supply and fixing of factory made POP corner moulding of 150mm wide in approved design. Moulding shall have reinforced steel bar to be anchored with ceiling to prevent falling of moulding or leaving surface.Quoted rate shall be including cost of sampling for approval , finishing and final touch, sanding , with two coat of primer and two coat of acrylic plastic emulsion paint of approved colour etc complete. Actual length of moulding fixed at site shall be measured for payments.

Diluting and injecting chemical emulsion for anti-termite treatment : Treatment of soil under floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Diluting and injecting chemical emulsion for anti-termite treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc.: With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration.

FALSE CEILING BOXES

Providing & fixing false ceiling at all height including providing & fixing of framework made of special section, power pressed from M.S. sheets and galvanised with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleat of size 25mm wide x 1.6mm thick with flanges of 27mm and 37mm, at 1200mm c/c, one flange fixed to the ceiling with dash fastener 12.5mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25 x10 x0.50mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I chanels 45 x15 x 0.90mm running at the spacing of 1200 mm c/c, to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26 mm each having lips of 10.5mm, at 450mm c/c, shall be fixed in a direction perpendicular to G.I intermediate channel with connecting clip made out of 2.64mm dia x 230mm long G.I wire at every junction, including fixing perimeter channels 0.50mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/ partitions with the help of Rawl plugs at 450mm centre, with 25mm long dry wall screws @ 230mm interval, including fixing of Calcium Silicate Board to ceiling section and perimeter channels with the help of dry wall screws of size 3.5 x25mm at 230mm c/c, including jointing & finishing to a flush finish of tapered and square edges of the board with recommended jointing compounds, jointing tapes,finishing with jointing compounds in three layers covering upto 150mm on both sides of joints and two coats of primer suitable for boards, all as per manufacture's specification and also including the cost of making opening for light fittings, grills, diffusers, cut outs made with frame of perimeter channels suitably fixed, all complete as per drawings, specificaton and direction of the Engineer in charge but excluding the cost of painting with:8 mm thick Calcium Silicate Board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process.

STRUCTURAL GLAZING AT ACTIVITY ROOM

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including: (a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)-cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including: (b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimentional movement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/structural steel framework of building structure using stainless steel anchor fasteners/ bolts, nylon seperator to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers. (c) Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shop environment, including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand and manufacture, as per the approved sealant design, within and all around the perimeter for holding glass. (d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site conditions, to seal the gap between the building structure and all its interfaces with curtain glazing to make it watertight. (e) Making provision for drainage of moisture/ water that enters the curtain glazing system to make it watertight, by incorporating 25.0 STRUCTURAL GLAZING ALUMINIUM COMPOSITE PANEL 407 SUB HEAD : 25.0 STRUCTURAL GLAZING ALUMINIUM COMPOSITE PANEL

Providing, assembling and supplying vision glass panels (SGUs) comprising of hermetically-sealed 10mm insulated glass (single glazed) vision panel units of size and shape as required and specified, comprising of heat strengthened glass 10 mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The SGUs shall be assembled in the factory/ workshop of the glass processor. (Payment for fixing of SGU Aluminium Panels in the curtain glazing is included in cost of item No.25.2) For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm. (i) Coloured tinted glass substrate with reflective soft coating having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement.

Extra for openable side / top hung vision glass panels (SGUs) including cost of providing glass and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineerin-Charge.

FURNITURE

Providing and fixing cup board shutters , doors , shelves , drawers in 18 mm thick, with Pre-laminated flat pressed commercial grade plywood, having one side decorative lamination and other side balancing lamination, including IInd class teak wood lipping of 25 mm wide x12 mm thick with with gloss polishing necessary screws and bright finished stainless steel soft closing hinges, complete as per direction of the Engineer-in-Charge. Thickness of decorative laminate shall be 1mm both sides, factory laminated , factory pressed. Actual one side area of plywood with laminate work shall be measured for payments.

Providing and fixing cup board shutters , doors , shelves , drawers in 12 mm thick, with Pre-laminated flat pressed commercial grade plywood, having one side decorative lamination and other side balancing lamination, including IInd class teak wood lipping of 25 mm wide x12 mm thick with with gloss polishing necessary screws and bright finished stainless steel stainless steel soft closing hinges, complete as per direction of the Engineer-in-Charge. Thickness of decorative laminate shall be 1mm both sides, factory laminated , factory pressed. Actual one side area of plywood with laminate work shall be measured for payments.

Providing , fixing and integration of SS304 long body recessed handles of 300 mm size. Hafle/Dorma/Hettich

Providing , fixing and integration of SS304 short body recessed handles of 150mm size . Hafle/Dorma/Hettich

Providing , fixing and brass tower bolt 75mm high . Hafle/Dorma/Hettich

Providing and Fixing drawer lock of 12mm dia of Godrej/Hettich/Epco

Providing and fixing cup board shutters , doors , shelves , drawers in 18 mm thick, with Pre-laminated flat pressed commercial grade plywood, having one side decorative lamination and other side balancing lamination, including IInd class teak wood lipping of 25 mm wide x12 mm thick with with gloss polishing necessary screws and bright finished stainless steel soft closing hinges, complete as per direction of the Engineer-in-Charge. Thickness of decorative laminate shall be 1mm both sides, factory laminated , factory pressed. Actual one side area of plywood with laminate work shall be measured for payments.( Decorative laminate sheets shall be issued by IISER Pune , balancing laminate has to be provided by bidder )

HARDSCAPING AND LANDSCAPING

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 16.91.1 60mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). cum 8376.15

Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).

Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).

Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge.

Supplying and stacking of good earth at site including royalty and carriage upto 5 km lead complete (earth measured in stacks will be reduced by 20% for payment).

Fine dressing of the ground by manual or mechanical means with necessary tools and labour etc complete.Fine dressing of ground suitable for lawning upto 100mm thickness.

Providing Circular Cement Concrete pots of specified size, cast with cement concrete of nominal mix 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 6 mm nominal size), reinforced with 7 Nos ( 3 nos horizontal & 4 nos vertical “ U “ shape) M.S. wires of 3.5 mm dia as per design, including required form work, finishing with cement punning on exposed surface, curing for specified period and stacking in required rows & height, all complete as per direction of Officer-in-charge.Top inside dia 30 cm, outer bottom dia 20 cm, total height 30 cm with wall thickness of 25.4 mm

Filling of the following size empty pots with mixture of good earth & manure in the ratio of 2:1 (Two part of Good earth & one port of manure) and placing them on approprite place i/c carriage of earth, manure and pots up to 50 mtr, as per direction of officer incharge. (The cost of good earth, earthen pots & manure will be paid seperately.) Size of Empty Pots 35cm Top dia, 25cm Bottom Dia & 35cm Perpendicular height.

Anti termite treatment of lawn area through premise 30.50% I P. one liter premise diluted in 499 liters water and applying solution @ 1.00 litre solution per sqm lawn or bed area.(two application) i/c cost of chemical)and as per direction of officer-in-charge.and as per direction of officer-in-charge.

Supply,filling , spreading , levelling and compaction of good quality mixure of 1:1 proportion disintegrated rock of stone size 5CM to 20CM and crush sand of proportion 1:1 to be laid in uniform layers of 150mm of required depth as per structural drawing below footing as subbase and as per instruction of Engineer In-charge.

Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge. Made of G.I. wire of dia. 4 mm, PVC coated to achieve outer dia not less than 5 mm in required colour and shade

SANITARYWARE AND CP FITTINGS

Providing, fixing, testing and commissioning of white vitreous china glazed floor mounted water closet (European type) of approved make With necessary water connection with integrated angle stop valve etc, complete and the EWC shall be with necessary check nut, stopcock etc., seat and lid, rubber buffers, etc. cutting and making good the walls and floors wherever required all complete as per specification and direction of the Engineer In-charge Approved Make Jaugar / Kolhar One Piece Floor Mounted EWC Jaquar LYS wht-38851- S Trap

Providing, installing, testing and commissioning of Vitreous China Pedestal Type European Water Closet (junior series) with seat and lid, low level Dual flushing cistern & 40 cm Cp. flush bend with fittings & CI brackets, over flow arrangement with specials of standard make and mosquito proof coupling and 15mm CP Angle valve of approved design complete including painting of fitting s and brackets cutting and making good the wall and floors wherever required, etc complete.Hindware- Pedestal Type European Water Closet (junior series) Poncho Water Closet –model no-20062

Providing, fixing, testing and commissioning of White color Wash basin above counter type with auto closing pillar tap (prismatic type ,The tap shall be complied flow rate at 2.75 / lpm at design pressure of 80 psi) , 32mm dia CP waste coupling, 32mm dia CP bottle trap with extension pipe, , 15mm CP angle valve with CP inlet connection tube with CP wall flange, etc complete . Jaugar FLS WHT 5931. Jaquar Angle Cock - Model -CON-059 KN , Jaquar Waste Coupling - Model - ALD-709 , Jaquar CP bottle trap-Jaquar-Allied-model no:ALD-769 L 300x190 ,Jaquar-auto closing pillar tap (prismatic type) model no PRS-031

Supplying,installing,testing and commissioning of Long body bib cock for Janitor including necessary accessories etc.complete. The pillar tap shall be complied flow rate at 2.75 / lpm at design pressure of 80 psi.Jaquar-Long body bib cock model no: CON-107 KN

Providing , fixing, testing and commissioning stainless steel kitchen sink with drain board ,32mm dia CP waste coupling, 32mm dia CP bottle trap with extension pipe, 15mm CP angle valve with CP inlet connection tube , CP wall flange, including necessary brakets etc complete.Nirli stainless steel sink with drai board size 510X1040 mm bowl depth 250 mm - Model - Elegance Jaquar Angle Cock - Model -CON-059 KN , Jaquar Waste Coupling - Model - ALD-709, Jaquar CP bottle trap-Jaquar-Allied-model no:ALD-769 L 300x190

Providing and fixing CP sink cock with swivel spout floor mounted etc, including cutting and making good the walls wherever required etc., all complete as directed by Engineer Incharge. (For Pantary)The pillar tap shall be complied flow rate at 2.75 / lpm at design pressure of 80 psi . Jaquar -Sink cock with regular swivel spout model no FLR-5437

Supplying and fixing cp Double Coat hook fixing with necessary screws etc., complete , Jaquar double hook - Model -ACN-1161N

Supplying , fixing in position and testing C.P. health faucet with wall hook one metre long flexible tube, 15mm CP angle cock with wall flange all complete including cutting and making good the walls wherever required.Jaquar CP Health Faucet - Model - ALD-573, Jaquar Angle Cock - Model -CON-059 KN

Supplying and fixing CP toilet paper holder fixed with SS screws complete.Jaquar Continental toilet paper holder - Model -CAN-1153 S

Providng and fixing 600mm long CP towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arangement of approved quality colour and make .Jaquar -towel Rail 600 mm long - Model no -ACN-1111 SM

Supplying, installing, testing, commissioning 2 in 1 CP wall mixer provision for over head shower with long bend pipe, connecting leg, spout, CP wall flange, wall mounded shower arm with wall flange and Over head shower etc complete, the works including necessary piping, cutting and making good the walls /floor wherever required, including cost and conveyance of all materials to the site, all labour charges, all taxes etc., complete finished item of work and as directed by the Site Engineer/ In-Charge. The quoted rate shall include cost of all the items given per no of fixture.Jaquar - Two in One wall mixer- model no:- FUS CHR 1989 , Jaquar - Shower arm with wall flange model no: SHA-483 , Jaquar - Over head shower- model no: OHS-1989

Supplying,fixing and commissioning of Soap Dish Holder, fixing with in the bath room walls etc., complete.Jaquar-Soap Dish Holder-model no:- ACN-1131N

INTERNAL WATER SUPPLY

Providing and fixing chlorinated Polyvinyl chloride (CPVC) pipes having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fitting including fixing the pipe with clamps at 1.00m spacing. this includes jointing of pipes &fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in charge.

Internal work –Exposed on wall

20 mm nominal outer dia .pipes

25 mm nominal outer dia .pipes

32 mm nominal outer dia .pipes

40 mm nominal outer dia .pipes

50 mm nominal outer dia .pipes

Providing and fixing chlorinated Polyvinyl chloride (CPVC) pipes having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fitting i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes &fittings with one step CPVC solvent cement and cost of cutting chases and making good the same include testing of joints complete as per direction of Engineer in charge.Concealed work including cutting chases and making good the wall etc.

15 mm nominal outer dia .pipes

20 mm nominal outer dia .pipes

25 mm nominal outer dia .pipes

Supplying, fixing and testing of approved make equivalent Brass ball valve with necessary specials such as unions, flange etc.complete

20 mm nominal bore

25 mm nominal bore

32 mm nominal bore

40 mm nominal bore

50 mm nominal bore

INTERNAL DRAINAGE

Providing, fixing and testing UPVC SWR- B Class pipe of approved Make confirming to IS 13592-1992. and fittings confirming to IS 14735-1999, such as coupler, elbow, bends, Tee, Y, vent cowl etc for Soil, Waste,vent and rain water pipe works in shaft and suspended in ceiling., laid in ground( from shaft to Inspection chamber and Gully chamber), etc., using rubber ring joints(rubber ring confirming to IS 15382) for shafts lines and solvent cement joints for suspended lines and work in below ground. Woks includes necessary scaffolding,cutting and making good the walls wherever required all complete as directed by the Engineer-in-Charge.

50mm dia

75mm dia

110mm dia

Supplying,fixing and testing of UPVC/ PVC floor trap with cockroach trap and CP grating 150 mm nominal size square 100mm diameter of the inner hinged round grating various inlet from 40 dia to 110 dia and various outlet from 75 dia to 100 dia with the extension pipe, boss tee connections, fixed in sunken floors /Suspended support with ceiling level etc., complete.

Supplying,fixing and testing of UPVC floor clean out used in sunken floors,75 or 110mm dia with extension pipes,specils such as 45 degrre bend , tee ,CP tile grating and end cap (clean out plug ).the cap arrangements with female thread fix with the upvc clean out plug in male thread with gascet and s.s screws etc. complete. Works including cutting and making good the walls /floor wherever required, etc., complete.

Fabricating,Supplying, fixing in position of Hot dipped Galvanized MS brackets made out of Angles, Channels, Flats and hot galvanized insert plates, according to the drawings at specified location at suitable intervals. The bracket shall be fixed both horizontally and vertically depending on the pipe locations such as shaft, ceiling, column faces and beam soffit etc. The rate shall include fixing the brackets/plates by using necessary size and dia of anchor fastners or any type fastening methodology approved by architect. The rate also include making cutouts/pockets in masonry wall to the suitable size in order to fix the bracket in wall and restore the finish after grouting the pocket with cement concrete etc. complete

External Water Supply

Providing and fixing chlorinated Polyvinyl chloride (CPVC) pipes, fittings up to 50 mm dia SDR 11 ASTM CTS and above 50mm dia CPVC schedule 80, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings this includes jointing of pipes & fittings with one step CPVC solvent cement,trenching, refilling &testing of joints complete as per direction of Engineer in Charge.External work.50 mm nominal outer dia pipes

Constructing masonry Chamber 120x120x100 cm, inside with 75 class designation brick work in cement mortar 1:4 ( 1 cement :4 coarse sand ) for sluice valve, with C.I. surface box 100 mm. top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix ( 1 cement :2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) necessary excavation foundation concrete 1:5:10 ( 1 cement :5 fine sand:10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 ( 1 cement :3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design.With F.P.S. bricks class

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete: 25 mm nominal bore

External Drainage

Excavating trenches of required width for pipes, cables, etc, including excavation for sockets and dressing of sides ramming of bottoms, depth upto 1.5 m including getting out the excavated soil and then, returning the soil as required in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming watering etc.and disposing of surplus excaveted soil as directed, with in a lead of 50mt.Pipes, cables etc. exceeding 80 mm dia but not exceeding 300 mm dia

Providing, fixing and testing UPVC Class-3 pressure rating 6 kg /sqcm pipe of approved Make for underground drainage and sewerage systems - Confirming to IS 4985:2000 - pipe in trenches to required gradients and provide sand cushion for pipes to the full width of trench above and below the pipe to required minimum thickness etc., complete. rates including for laying pipes,forming bottom surface to required level, etc., complete 160mm diameter

Constructing brick masonry manhole in cement mortar 1:4 (1cement:4 graded stone aggregated 20mm nominal size), foundation concrete 1:4:8 mix (1cement:4coarse sand: 8graded stone aggregated 40mmsize nominal size) in side plastering 12mmthick with cement mortar 1:3(1cement:3coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1cement :2coarse sand :4graded stone aggregate 20mm nominal size) finished with floating coat of neat cement complete as per standard design: Inside size 90x80 cm and 45cm deep including C.I cover with frame (light duty )455x610mm internal dimensions total weight of cover and frame to be not less than 38kg(weight of cover 23kg and weight of frame 15 kg): With Sewer bricks conforming to IS:4885

Making connection of drain or sewer line with existing manhole including breaking in to and making good the walls, floors with cement concrete 1:2:4 mix (1 cement: 2coarse sand: 4 graded stone aggregate 20 mm nominal size) cement plaster on both side with cement plaster 1:3 (1cement:3 coarse sand) finished with a floating coat of neat cement and making necessary channels for drain etc.completeFor pipes 100 to 250 mm diameter

Providing and fixing square-mouth S.W.gully trap grade ‘A’’ complete with C.I grating brick masonry chamber with water tight C.I cover with frame of 300x300mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70kg as per standard design :100x100 mm size P type, With Sewer bricks conforming to IS:4885

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenchs or drains (not exceeding 1.5 m in width or 10sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5m, including getting out the excaveted soil and disposal of surplus excaveted soil as directed, within a lead of 50m.All kinds of soil (for manhole)

AdditionalExtra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials. All kinds of soil (for manhole)

SECTION- A- POINT WIRING AND ACCESSORIES

COPPER WIRING IN PVC CONDUITS

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with piano type switch, phenolic laminated sheet, suitable size M.S. box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as

Group A

Group B

Group C

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 2 Nos. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

Supply & fixing following modular switch/ Socket on the exisitng modular plate & switch box including connection but excluding modular plate etc. as required

5/6 amps switch (For Power socket)

15/16 amp switch (For Power socket)

3 pin 5/6 amp socket outlet (For Power socket)

6 pin 15/16 amp socket outlet (For Power socket)

Supply and fixing modular blanking plate on the exisitng modular plate & switch box with matching colour including connection but excluding modular plate etc as required.

Supply & fixing following size/modules, GI box along with modular base and cover plate for modular switches in recess etc as required.

1 or 2 Module box (95mmx95 mm)(For Data Purpose)

3 Module box(100mmx95 mm)(For Power socket/ELV Purpose)

4 Module box(125mmx95 mm)(For Power socket/ELV Purpose)

6 Module box(200mmx95 mm)(For Power socket/ELV Purpose)

8 Module box(125mmx125 mm) (For Power socket/ELV Purpose)

12 Module box(200mmx150 mm)(For Power socket/ELV Purpose)

Supply & fixing following modular base and cover plate for modular switches in recess etc as required.

1 or 2 Module (For Data point Purpose)

3 Module (For Power socket/ELV Purpose)

4 Module (For Power socket/ ELV Purpose)

6 Module (For Power socket/ ELV Purpose)

8 Module (For Power socket/ ELV Purpose)

12 Module (For Power socket/ELV Purpose)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings).

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required.

Supplying and fixing brass batten/Angle holder including connection etc.as required

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.

Upto 450 mm sweep

Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes.

SECTION - B- MV CABLE SUPPLY, LAYING & TERMINATIONS

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required

Upto 35 sq. mm

Above 185 sq. mm and upto 400 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing masonry open duct as required.

Upto 35 sq. mm

Above 185 sq. mm and upto 400 sq. mm

MV Cable Jointing & End Termination

Supplying and making indoor end termination with brass compression gland and aluminum lugs for following size of PVC insulated and PVC sheathed /XLPE aluminum conductor cables of 1.1kV grade as required.

3½ X 35 sq. mm (28mm)

4 X 16 sq. mm (28mm)

Supply Of M.V. Cables & Cu-Cable Termination

M.V. ALCable supply : Supply, loading, transportation unloading at site, storages at site ,shifting from storage place to site, of 1100 Volts grade XPLE insulated over all FRLS outersheathed , Aluminium conductor, armoured LT power cables as per IS 9098(Part 1) of following sizes.( Note :- Cable shall be considered Round armoured type )

3.5 x 35 sq.mm ALuminium ,XLPE Armourd Cable

4 X 16 sq. mm copper ,XLPE Armourd Cable

M.V. Cu Cable supply : Supply, loading ,transportation unloading at site, storages at site ,shifting from storage place to site, of 1100 Volts grade XLPE insulated over all FRLS outersheathed, Copper conductor, armoured LT power cables of as per IS :1554 (Part 1) of following sizes. .( Note :- Cable shall be considered Round armoured type )

3X2.5 sq.mm Copper ,XLPE Armourd Cable

End termination of Cu cable : Supply, loading ,transportation unloading at site, storages at site ,shifting from storage place to site,and making end termination with brass compression gland and copper lugs for following size of PVC insulated and PVC sheathed/ PVC COPPER conductor cable of 1.1KV grade of following sizes as required

3X2.5 sq.mm Copper ,XLPE Armourd Cable

SECTION -C-CABLE TRAYS ASSOCIATED WORKS

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 19.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "bends" (galvanisation not less than 50 microns) with perforation not more than 19.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Tee" (galvanisation not less than 50 microns) with perforation not more than 19.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

SECTION -D-LIGHTING FIXTURES & WALL MOUNT FANS

Supply & installation testing commissioning ,loading ,transportation, unloading at site, storages at site of following type light fittings including required integral control gears, lamps,& other accessories etc to complete the work as per Engineer -In -charge.

Supply Testing commissioning of surface Mounted 18W,IP-20 LED SURFACE MOUNTED LUMINARIES,CCT=6000K,LUMEN OUTPUT=2000.EQUI. TO PHILIPS CAT NO.SM251C LED20S-6500 PSU WH

14W LED BOLLARD DECORATIVE LUMINARIES CCT=5900, LUMEN OUTPUT=900 EQUI. TO PHILIPS CAT NO. BCP 400 LED09D CW

16W,IP-20,LED SURFACE MOUNTED LUMINARY EQUI. TO CCT=CW(6500K), LUMEN OUTPUT=2000 . EQUI. TO PHILIPS CAT NO. BN308C LED20S-6500 L120 PSU WH

15W WALL MOUNTED DECORATED FITTING-IP20,CCT=CW(4500K), LUMEN OUTPUT=1500

10W MIRROR LIGHT.EQUI. TO PHILIPS CAT NO. BN 021 LED10S- 6500 PSU GR S1

Supply, of Exhaust fan 150mm light duty 230 V AC 50 Hz 450 mm 1400 RPM with condenser complete erected in position with n/c materials Fan motor with moisture treatment and class E insulation & With bird protective screen

Supplying and fixing two modulestepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required

Supply and fixing, of 1200 mm, 230V, 50Hz, ceiling fan, colouful, designed & graphics designs for kids , as complete with all accessories like down rod min 30 cm, caps , wiring , connector etc as complete including Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required.Model equivelent to Havells safari saurous worls/ Unicorn/Ocean Quest as per direction of engineering Incharge.

Supply and fixing, of 1200 mm, 230V, 50Hz, ceiling fan, colouful, designed & graphics designs for kids , as complete with all accessories like down rod min 30 cm, caps , wiring , connector etc as complete including Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required.Model equivelent to Havells model no. FHCSYSTPWT48 12500MM STEALTH AIR as per direction of engineering InCharge

SECTION -E-EARTHING & EARTHING

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thickincluding accessories, and providing masonry enclosure withcover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.

Providing and fixing earth bus of 50 mm X 5 mm G.I. strip on surface for connections etc. as required.

SECTION F MCCB,MCB&DB'S

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

8 way (4 + 24), Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required

Single pole

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required

Supplying and fixing DP sheet steel enclosure on surface/ recess along with 25/32 A 240 V "C" curve DP MCB complete with connections, testing and commissioning etc. as required.

SECTION G- MISCELLANEOUS

Supply, fabrication and installation of cable tray supports, supports for cable trench covers, supporting frame for mounting of control panels, supports for mounting of local control station,Main Electrical Panel,lighting panel, lighting fixture etc. with 2 coats of enemel primer and 2 coats of epoxy paint Note - The rates shall be inclusive of grouting of supports , Anchor fastner,welding rods, nut,bolts,clamps,and any other consumable which required to complete the works.

SECTION H- HVAC

Supply of 2TR Capacity Hiwall type air condition with minimum 4 star ratings with cordless remote and outdoor unit mounted with suitable stand with R410 or green refrigenat gas only.

Supply of 1.5 TR Capacity Hiwall type air condition with minimum 4 star ratings with cordless remote and outdoor unit mounted with suitable stand with R410 or green refrigenat gas only.

Installation, testing charges of Hiwall type AC

Supplying & fixing of copper refrigerant piping with minimum 9 mm insulation complete from indoor unit to outdoor unit with supports Etc.

Supplying and laying of 3 x 4.0 sq mm PVC insulated copper conductor flexible cable.

Supplying & fixing 25/32 mm size PVC drainage pipe with insulation i/c cutting the wall, finishing etc. as reqd.

Supply and installation of M.S. stand for outdoor units

Supply and fixing of 16 Amps TPMCB along with enclose box of steel type.

SECTION-1- FIRE DETECTION & ALARM SYSTEM

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required. NOTE:- fire Alarm system shall be connected to nearest Fire alarm panel as per site condition

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector for below false ceiling & True ceiling(above false ceiling) complete with mounting base complete as required.

Supplying, installation, testing & commissioning of fault isolator complete with base as required.

Supplying, installation, testing & commissioning of intelligent addressable thermal detector with rate of rise cum fixed tempreature thermistor complete with base as required.

Supplying, installation, testing & commissioning of addressable fire control module complete as required.

Supplying, installation, testing & commissioning of addressable manual call point complete as required.

Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required.

SECTION -3-DATA/LAN & TELECOM PASSIVE COMPONENTS

UTP CAT6 COMPONENTS Supply and laying of specified make Unarmoured UTP CAT6 cable in prelaid PVC conduits or pipes or raceways or cable trays, but without the cost of conduits or pipes or raceways or cable trays. The cable is to be drawn from individual workstation area/device/IO to the nearest distribution rack or networking rack. It shall be within the scope of contractor to carry out and submit scanner readings for all IOs meeting the requirements of relevant EIA/TIA standards as per CAT6 cabling requirements. The contractor shall submit a detail IO maps, labelling and documentation related to terminations. It shall be as per technical specifications with all the necessary mounting accessories as required for complete installation.

Supply , installation, testing and commissioning of network switch with 24 ports PoE ethernet port as per specifications :

Supply, Installation, Testing & Commissioning of UTP CAT6 Angular patch panel pre-loaded with 12 ports in 1U form factor, with universal A/B labeling and 110 connector terminations on rear of panel allowing for quick and easy installation of 22 to 24 AWG cable, inclusive of termination of UTP CAT6 cables at all12 ports. It shall be as per technical specifications with all the necessary mounting accessories as required for complete installation.

Supply, Installation, Testing & Commissioning of single UTP CAT6 I/O of specified make with different colours for differentiating Data, Voice & Wifi and other services inclusive of termination of UTP CAT6 cable at each I/O as required as per drawing. The IO shall be mounted inside singlex or duplex or quad faceplate as applicable and using suitable backbox assembly. It shall be as per technical specifications with all the necessary mounting accessories as required for complete installation.

Supply, Installation, Testing & Commissioning of faceplate with blank Inserts and corresponding MS backbox assembly for installation of: MS backbox assembly shall be provided for outlets installed at wall or at furniture, wooden or any partition at workstation area/device for flush mounting. For exposed mounting, PVC backbox assembly shall be provided. It shall be as per technical specifications with all the necessary mounting accessories as required for complete installation.Single I/O faceplate

Supply, Installation, Testing & Commissioning of UTP CAT6 RJ-45 Patch Cords Solid Conductor of various lengths with different colours for differentiating Data, Voice & Wifi and other services. It shall be as per technical specifications with all the necessary mounting accessories as required for complete installation.

1 meter

2 meters

FIBER OPTIC CABLE & COMPONENTS Supply, Installation, Testing & Commissioning and Laying of fiber optic cable of various capacities to be laid in prelaid conduits/RCC hume pipes/HDPE/DWC/cable trays as applicable. It shall be as per technical specifications with all the necessary mounting accessories as required for complete installation.work including cable splicing & with LC/SC connetion of fire optics cable & dressing of cable in racks with connection of nework switch.06 cores OS2 Singlemode armoured fiber cable, uni-tube, high density polyethylene outer jacket.

NETWORKING ENCLOSURES Supply, Installation, Testing & Commissioning of 19" wide mounting frame Networking Enclosures of various sizes and capacities complete with all accessories. It shall be as per technical specifications with all the necessary mounting accessories as required for complete installation.15U, 600mmW x 600mmD, wall mounted, 2 x 90cfm fans.NOTE :- Additional network rack shall be connected to Nearest Existing I.T Rack

SECTION-4-IP BASED CCTV SYSTEM

Supply Installation Testing & commissioning of 2MP IR DOME CAMERA , with fixed Lens, 1/3" Progressive Scan CMOS, ICR, 0 lux with IR, 1920x1080: 25/30fps, 2.8 mm lens, H.264/MJPEG, dual -Stream, BLC, UP to 30m IR, Vandal-proof, DC12V/PoE , Full HD, DWDR, 3D DNR, Smart IR, 30m IR, Support Intrusion detection, line crossing. ONVIF, UL LISTED. CERTIFICATE CE & FCC.

Supply & Fixing of Media convertor with POE Convertor for (UTP Modules for connecting L2 Switches with Core Switches)

Supply Instalaltion Testing and commissioning of CAT 6 , UNARMOURED UTP CABLE equvillant to to D-Link,AMP/digilink/ Cisco

SITC of IP, 16CH NVR, 2 SATA HDD Slot (Max 8TB), with 4 TB hard disk of approved make, 12VDC,Realtime Recording Resolution (16 Channels @ 720P,8 Channels @1080P),Real-time Local Playback( 4 Channels @720P,2 Channels @1080P),Multiplex Operation,H.264 High profile,BNC/VGA/HDMI output, main profile, baseline,HDD Redundancy,Free DDNS,Network backup, USB HDD, USB writer, SATA writer,1 RS485, support 18 kinds of PTZ protocols,ONVIF 2.0,1 channel Audio Input and Output, Make-Honeywell CALNVR-2016B or equivalent approved make.

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mmsolid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existingsurface/ recessed steel/ PVC conduit as required.

22'' Full HD monitor LED backlit Computer Monitor , Full HD .Borderless,IPS Monitor, Brightness intelligence,adaptive eye care technology, dual HDMI and built in speaker

32'' Full HD LED TV viweing angle more than 170 degree, wall mounted,in built spaeker min. 10W HDMi inputs 2 nos. , USB input 1 nos for NP4 , NP3 , WMI formats

Providing and fixing expandable fasteners of specified size with necessary plastic sleeves and galvanised M.S. screws including drilling holes in masonry work /CC/ R.C.C. and making good etc. complete.50 mm long

ALL ABOVE QUOTED RATES OF ALL ITEMS SHALL BE INCLUDING COST OF ALL TAXES , DUTIES , ROYALTIES , LEAD , LIFT , TRANSPORTATION AND GST , NOTHING EXTRA SHALL BE PAID SEPARATELY. BIDDER SHALL ERECT HARD BARRICADING WITH GI SHEETS-MS SUPPORTS UP TO HEIGHT OF 3 METERS AROUND CONSTRUCTION SITE BEFORE STARTE OF WORK AND UP TO COMPLETE PROJECT DURATION. NOTHING SHALL BE PAYABLE SEPARATELY ON ACCOUNT OF SITE BARRICADING.IF BARRICATION NOT DONE RECOVERY SHALL BE MADE AS PER CPWD DSR 2018 FOR NECESSARY ITEMS AND QUANTITY. ON COMPLETION OF SITE , BIDDER SHALL CLEAR PLOT FROM CONSTRUCTION DEBRIS , EXCESS MATERIAL OR SCARP BEFORE HANDING OVER. ALL SAMPLES SHALL BE GOT APPROVED FROM ENGINEER IN-CHARGE BEFORE MASS PRODUCTION OR BULK PROCUREMENT.

SYNERGY SKI INFRADEVELOPMENT

Surendra Infrastructure Pvt. Ltd.

M/S.RZMALPANI