SPL REPAIRS TO BLDG NO P 331 OF 27 MTN DIV SIG REGT AND SPECIAL REPAIRS TO ROOF FALSE CEILING AND JOINERY IN BLDG NO P 94 AND P 206 AND PROVISION OF TOILET BLOCK NEAR BLDG NO T 56 AT 627 EME BN AT KALIMPONG MIL STN UNDER GE 867 EWS

Amount

Surface dressing n exc 15 cm deep and getting out in soft/loose soil all as specified and as directed (Including Site Clearance).

Surface excavation n exc 30 cm deep and averaging 15cm deep and getting out soft soil.

Excavation in trenches not exc 1.5 mtr wide and not exc 1.5 mtr in depth; for foundation etc. and getting out in Soft/ loose soil.

Returning filling in , including, spreading, levelling, watering and well ramming in layers not exc 25cm in soft / loose soil.

Removing excavated material n. exc 50m and depositing where directed at a level n. exc 1.5m above the starting point in soils.

Removing excavated material exc 50m but n.exc 250m and depositing where directed at a level n. exc 1.5m above the starting point in soils.

M & L PCC (1:4:8) type D-2 (Using 40 mm grade aggregate) in foundation, filling and mass concrete.

S&F Pre- painted galvalume aluminum zinc coating GI based steel sheet (AZ-150) of approved profile of corrugation, 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws including dismantling of plain or corrugated steel sheeting, any gauge and thickness including Nainital or similar pattern roof coverings inclding dismantling of plain or corrugated steel sheeting, any gauge and thickness including Nainital or similar pattern roof coverings complete all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick (AZ-150) of any colour having tensile strength of 550 Mpa as in roof covering, eaves board, ridges, hips,valley gutters, drip and straight flashing cladding to wall etc, fixed with self tapping screws including dismantling of plain or corrugated steel sheeting, any gauge and thickness including Nainital or similar pattern roof coverings inclding dismantling of plain or corrugated steel sheeting, any gauge and thickness including Nainital or similar pattern roof coverings complete all as specified and directed.

S&F for pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed.

Dismantling timber fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section.

M&L for 2nd class hard wood Plain fillets of sectional area exc. 13 and not exc. 25 sqcm.square, rectangular or triangular in section, clean sawn, secured with nails or brads complete.

S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc including dismantling wrought iron or mild steel work of any description complete all as specified and directed.

S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specified and directed.

Dismantling timber scantlings 40 Sqcm and over in section, in any position (framed work) all as specified and directed.

S&F false ceiling with powder coated exposed GI grid suspension system (E-Grid T-2430 or equvalent load carrying capacity with mid span deflection not exc. 1/360 span with hanger spacing of 1200mm c/c) consisting of main runner 3600mm long, cross Tee 1200mm/600mm long and wall angle. The main runners to be placed @ 1200mm, the cross Tee 1200mm will be inserted in the pre cut slots of main runner at a regular interval of 600mm to form a modular grid of 1200mmX600mm. Additional cross Tees of 600mm shall be placed perpendicular to the cross tee 1200mm long to finally form a grid of 600mmX600mm. Suspensor system (Grid) made out of GI sheet main Tee of size 23.5mmx38.50mmX0.36mm and cross Tee of size 23.5mmX23.5mmX0.36mm and angle size 19mmx19mmX0.36 mm. Grid of modular size 600mmX600mm shall be supported by 4 mm dia G.I. wire from purlins/soffit with and including 4mm thick high pressure steam cured non asbestos fiber cement designer ceiling board (Density>1200Kg/Cum) of size 595mmX595mm, confirming IS 14862 & Type B Category III of ISO 8336, tested as per AS 1530 part 3 & BS-476 Part 4, 5, 6, 7 & 8, complete all as per manufacturer's instruction. (Make : Everest or equvalent as approved by GE)

S&F in repair false ceiling with powder coated exposed GI grid suspension system (E-Grid T-2430 or equvalent load carrying capacity with mid span deflection not exc. 1/360 span with hanger spacing of 1200mm c/c) consisting of main runner 3600mm long, cross Tee 1200mm/600mm long and wall angle. The main runners to be placed @ 1200mm, the cross Tee 1200mm will be inserted in the pre cut slots of main runner at a regular interval of 600mm to form a modular grid of 1200mmX600mm. Additional cross Tees of 600mm shall be placed perpendicular to the cross tee 1200mm long to finally form a grid of 600mmX600mm. Suspensor system (Grid) made out of GI sheet main Tee of size 23.5mmx38.50mmX0.36mm and cross Tee of size 23.5mmX23.5mmX0.36mm and angle size 19mmx19mmX0.36 mm. Grid of modular size 600mmX600mm shall be supported by 4 mm dia G.I. wire from purlins/soffit with and including 4mm thick high pressure steam cured non asbestos fiber cement designer ceiling board (Density>1200Kg/Cum) of size 595mmX595mm, confirming IS 14862 & Type B Category III of ISO 8336, tested as per AS 1530 part 3 & BS-476 Part 4, 5, 6, 7 & 8, complete all as per manufacturer's instruction. (Make : Everest or equvalent as approved by GE)

M&L for non skid ceramic coloured tiles 7 to 8 mm thick premium quality conforming to IS-13712, grade B-II(a) (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces of tile over and including 20 mm thick screed bed in cement mortar 1:6 including dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing ) removing serviceable tiles to store and rubbish off the premises includicomplete all as specified and directed.

M&L for Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the surfaces of tile over and including 15 mm thick screed bed in cement mortar 1:4 including dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing ) removing serviceable tiles to store and rubbish off the premises includicomplete all as specified and directed.

M & L Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bed or bedding layer in CM 1:6.

M&L 350X250 mm X7mm thick / 450X350X7mm thick coloured glazed ceramic tiles fixed as in vertical surface such as risers of steps, skirting, dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile over and including 10 mm thick backing plaster in CM 1:4 finished even and rough complete all as specified and directed.

M&L for brickwork with fly ash bricks straight or curved on plan exc 5 mtr mean radius built in cement mortar 1:6 Demolition of brick work or stone/boulder masonary buit in cement mortar including all quions ,arches ,pillars etc but excluding ashler facing dressed stone work and precast concrete and directed.

M&L for brick work with fly ash bricks straight or curved on plan exc 6 m straight or curved fly ash bricks built in cement mortar 1:6 complete all as specified and directed

M&L for brickwork with flyash brick, straight or curved on plan to any radius in half brick thick walls, built in cement mmortar 1:6 complete all as specified and directed

M & L hard core of gauge n. exc 63mm, deposited, spread and levelled in layers n. exc 15cm thick watered and rammed to a true surfaces in broken stone or boulders.

M & L 75mm thick Cement concrete type D-2, (1:4:8) (40mm graded aggregate) as in sub base floor all as specified and directed.

M&L PCC (1:3:6) Type C1 using 20mm stone aggregate as in plith protection complete all as specified and directed.

M/L machine pressed polished coloured precast concrete interlocking paver block conforming to IS-15658-2006 of 80mm thick, M-35 Grade of any shape or color with mixture of grey cement and pigment over 50mm sand cushioning complete all as specified and directed.

M & L Cement concrete type C 2 (1:3:6) (40mm graded aggregate) as in surface channel and drains complete all as specified and directed.

M & L extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement including forms, moulds mitred / stopeed endes etc., complete all as specified and directed.

M & L Damp proof course 40 mm thick in cement concrete (1:2:4) Type B-0 to horizontal or vertical surfaces including necessary formwork complete all as specified and directed.

M & L Reinforced cement concrete Type B1 (1:2:4) (20 mm graded aggregate) plinth Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

Form work to sides and soffits of floor or roof beam, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc also splays between floors and beams,etc., complete all as specified and directed.

M & L TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M & L TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M & L Granite (of any type) work 20mm thick (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including demolition of stone slabs and tiles of any description or thickness in floors, aprons etccomplete all as specified and directed by Engr - in - Charge.

M/L for chequered cement concrete tiles with grey cement and pigment 30cmX30cm X 25mm thick set jointed and pointed in neat cement slurry over 15mm thick screed bedding layer in CM (1:6) complete all as specified and directed.

M & L cement concrete Type B1 (1:2:4) graded aggregate) (20 mm in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed.

M&L for PCC 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate) as in bed blocks for grouting hold fasts , coping, filling in pressed steel chowkat or similar work including necessary form work as required complete all as specified and directed.

M&L for 75 mm thick PCC (1:3:6) type C-2 using 40mm graded crushed stone agg as in plinth protection/ path laid slope of 1 in 12 and finshing cement concrete surface even and smooth without using extra cement with and including all necessary form work to divide the area in panels, finishing exposed edges fair or rounding or chamfering of exposed edges or as directed by engr -in-charge.

Taking down cement plaster on brick or stone masonry surfaces of walls etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar (1:6) on fair faces of brick work or concrete surfaces including Taking down cement plaster on brick or stone masonry surfaces of walls etc complete all as specified and directed. complete all as specified and directed.

M&L 20 mm thick rendering ( in two coats 10mm+5mm) on fair faces of brick work or concrete surface in cement mortar (1:4) on external wall finished even and fair mixed with integral water proofing compound @ 2% by weight of cement in 2nd coat or in the manner specified by the manufacturer and in the proportions indicated complete all as specified and directed. Note:-WPC will be measured and paid separately as supply only.

Supply only integral water proofing compond all as specified and as directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper over a coat of white wash complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of cement base paint complete all as specified and directed.

M&L for preparation of old plastered surfaces and applying two coats of oil bound distemper on wallls complete all as specified and directed.

M&L for preparation of old plastered surfaces of wall and applying two coats of cement base paint complete all as specified and directed.

M&L for preparation of old plastered surfaces and applying two coats of white wash on walls complete all as specified and directed.

M&L for preparation of new plastered surfaces and applying two coats of white wash on walls complete all as specified and directed.

M&L preparation of new steel surfaces of any description over 10 cm width or girth not otherwise described and applying two coat of synthetic enamel paint over a coat of red oxide complete all as specified and directed.

M&L preparation of old steel surfaces of any description over 10 cm width or girth not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L preparation of new wood or wood based surfaces of any description over 10 cm width or girth not otherwise described and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L preparation of old wood or wood based surfaces of any description over 10 cm width or girth not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

Taking down shutters of any description exc 1 sqm and n exc 2 sqm each and refixing in same opening after Resecuring or easing & adjusting complete all as specified.

Taking down chowkhats or frame not exc 1.50 sqm each with shutter (without taking off shutters from the frame) complete all as specified and directed.

Taking down chowkhats or frame exc 1.50 and not exc 4 sqm each with shutter (without taking off shutters from the frame) complete all as specified and directed.

S&F Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed

S&F second class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats

S&F steel window with side hung shutter, including box type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified.

S&F steel window with side hung shutter, including box type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified.

S & F Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed.

S&F 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sidescomplete all as specified and directed.

S&F 35 mm thick (batten thickness) second class hard wood, glazed and Skelton shutters, open rebated and prepared to receive glass, gauge, etc , divided into squares, with plain chamfered or rounded, mitred and without sash bars, edges of framing plain, chamfered or rounded with cut mitred beds for securing glass etc, supplied and fitted to chowkhats complete all as specified and directed. (Note :- The dimension of the various components or parts of shutters shall be as specified in clause 8.24 (a) of MES SSR 2009 Part I)

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm single side prelam PVC sheet used reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

All as per item no.65 but single side prelam PVC sheet used instead of plain colour PVC sheet complete all as specified.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles a PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; t both side Prelam PVC sheet used instead of Plaincolour PVC sheet. Stile and rails feathered at edges beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

All as per item no.67 but both side prelam PVC sheet used instead of plain colour PVC sheet. Stile and rails feathered at edges complete all as specified and directed.

S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.50 sqm in each pane complete all as specified and directed.

S&F in repairs 4 mm thick figured glass, pin head type and glazing with oil putty in square not exc 0.50 sqm in each pane complete all as specified and directed.

S & F 4 mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia if wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F in repairs stainless steel wire cloth 0.36mm nominal dia if wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F mild steel framed work such as grills, grating etc with end of bars shouldered and/ or riveted or forged into spikes, framed guard bars,barred iron doors, ladders, framed balusters, walk ways, railings and similar work confirming to Fe-410-0 or Fe 310-0 complete all as specified and directed.

S&F Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 fixed all as specified and directed.

S&F of 150 mm long aluminium, anodised, barrel tower bolt, of extruded section and fixed all as specified and directed.

S&F Mild steel barrel tower bolts 100mm, stove enamelled black, with bright bolt and fixed complete all as specified and directed.

S&F 150 mm size Aluminium handles, cast type, anodised and fixed all as specified and directed.

S&F Mild steel barrel tower bolts 75mm, stove enamelled black, with bright bolt and fixed complete all as specified and directed.

S&F Butt hinges 100mm, medium weight, cold rolled mild steel, and fixed complete all as specified and directed.

S&F Mild steel pressed handles 100mm, oval type, stove enamelled black complete all as specified and directed.

S&F Hasp and staple, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.

S & F Butt hinges, 100 mm size, heavy weight, cold rolled mild steel, and fixed complete all as specified and directed.

S & F Mild steel barrel tower bolts 200 mm, stove enamelled black, with bright bolt and fixed complete all as specified and directed.

S & F 150mm long aluminium handle cost type anodised complete all as specified and directed.

M&L preparing new wood surfaces and treated with tar or coal tar black paint all as specified and directed.

S&F of PVC low level flushing cistern 10 Ltr capacity, valveless syphonic action type complete with inlet, ball valve, float valve, bends brackets, rawl plug, brass screws handle etc complete having BIS description mark with IS-2731 with and including suitable size of MS brackets, plug, screw all as required incl taking down existing high level/low level flushing cistern any type disconnecting pipes and jointing with new one etc, and making good the floors/walls as per existing floor finish/wall finish including 32 mm bore PVC flush pipe and jointing with water closet of any type all as specified and directed.

S&F in repairs water closet (squatt pattern) of vitreous china squatting pan of pattern "ORRISA" pattern size 580 x 440 mm white with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and flushing pipe anti syphonic pipe etc complete including trap set in and including necessary lean cement concrete complete all as specified and directed.

S&F in repairs water closet (squatt pattern) of vitreous china squatting pan of pattern "ORRISA" pattern size 630 x 450 mm white with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and flushing pipe anti syphonic pipe etc complete including trap set in and including necessary lean cement concrete complete all as specified and directed.

S & F Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F in repairs Vitreous China wash basin, flat back, size 600x480mm white, excluding taps, waste, chain and plug and rcelain stopper but including brackets complete all as specified and directed.

S & F Vitreous China wash basin, angle back, size 500x400mm white, excluding taps, waste, chain and plug and porcelain stopper but including brackets, cutting for & plinning in ends of brackets or erecting stands.

S & F Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe)Vitreous China urinals, bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar (1:2), securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe)

S&F Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms complete all as specified and directed.

S & F bib taps 15mm bore cast copper alloy chromium plated with crutch or butter fly handle, screwed down, screwed for iron pipe or for brass ferrule & fixed complete all as specified and directed.

S & F Grating doom 100mm dia of PTMT (Minimum weight 25gms) complete all as specified and directed.

S&F in repair 15 mm bore chromium plated bib tap fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S & F Stop cock 15 mm bore cast copper alloy screwed down high pressure fancy type, chromium plated with long shank and cup (concealed type) complete all as specified and directed.

S&F in repairs angle , stop valve 15 mm bore, chromium plated, fancy type, with wall flange, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S & F Pillar taps 15mm bore, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

S&F in repairs pillar taps, cast copper alloy, with capstan heads, chromium plated,fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

S&F in repairs brass chromium plated tubular towel rail of 20mm dia D' type 60cm long between flanges complete all as specified and directed.

S&F in repair PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

M &L PVC connections 15mm size with PTMT nuts of length 300mm complete all as specified and directed.

S&F CP towel Rail 20mm dia, D type, 60cm long between flanges etc, complete all as specified.

Cutting chases, pinning in brick/pcc block wall and making good to facings where equired and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed.

S&F of 110 mm PVC (SWR) drain pipe single socketed in any length with rubber ring joints fixed to walls including taking down existing complete all as specified and directed.

S&F of 75 mm PVC (SWR) drain pipe single socketed in any length with rubber ring joints fixed to walls including taking down existing complete all as specified and directed.

S & F PVC (SWR) pipe 75mm bore single socketed in any length with rubber ring joint fixed to wall (ISI Marked) all as specified and as directed.

S&F 110 mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F PVC (SWR) branch pieces 75 mm (Single Y) equal or unequal complete all as specified and directed.

S&F PVC (SWR) branch pieces 110 mm (Single Y) equal or unequal complete all as specified and directed.

S&F of 110 mm bore PVC (SWR) bend any radius with access door complete all as specified and directed.

S&F of 75 mm bore PVC (SWR) bend any radius with access door complete all as specified and directed.

S&F PVC (SWR) gully trap 110 mm bore, setting jointing with solvant cement complete all as specified and directed.

S&F 75 mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

M & L for PCC (1:3:6) type C-2 as in Concrete bed to drain pipes 150 mm dia including packing under, and haunching against the sides of pipes after they are laid and tested complete all as specified and directed.

S & F Supplying and laying of CPVC pipes 20mm outer dia SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

Taking up or down 15 mm bore old steel tubing and connections, including disconnection of fittings from tubing including cleaning for re-fixing or removal from site complete all as specified and directed.

S&F of 15 mm bore tubes medium grade galvanised with and incl all GI fitting (such as bends, elbows, Tees, connectors, short pieces, back nuts, unions, caps and plug etc ) and fixed complete to wall and ceiling or laid in/on floor complete all as specified and directed.

Material and labour for point wiring with 1.5 Sqmm (nominal area) PVC insulated un - sheathed single core multi stranded copper conductor FRLS cable 1100 volts grade (conforming to IS) drawn through and including rigid non metallic PVC casing and capping not less than 20mm size, medium grade with all necessary fittings, surface wiring , for light /Bell point controlled by one switch including 1.5 Sq mm PVC insulated copper stranded conductor for earth continuity conductor and connected to earth dolly and to be terminated in 1.6 mm thick pressed steel terminal boxes/ on PVC rectangular block with 3 mm thick plastic laminated sheet cover of suitable size (concealed type in permanent bldg and surface in temporary bldg or as directed ) for mounting fittings like switch, socket, fan regulator etc. with 3 mm thick laminated bakelite sheet cover ,for housing switches, socket outlet, regulator etc., testing on completion including taking down existing poit wiring complete all as specified and directed.

All as per item No.123 here-in-before but One 3 pin socket outlet 5/6 Amps on the same board with other switchs with cables 1.5 Sqmm size.

All as per item No.123 here – in – before but for one 3 / 5 -pin switch socket outlet 5/6 amps on independent board.

All as per item No.123 here – in – before but for one switch socket outlet 15/16 Amps on independent board with 2.5 Sqmm multi stranded and 2.5 Sq mm stranded (for earth) PVC insulated un-sheathed copper cable.

Material and labour for point wiring with 1.5 Sqmm (nominal area) PVC insulated un - sheathed single core multi stranded copper conductor FRLS cable 1100 volts grade (conforming to IS) drawn through and including rigid non metallic PVC conduit not less than 20mm dia, medium grade with all necessary fittings, Concealed wiring , for light /Fan point controlled by one switch including 1.5 Sq mm PVC insulated copper stranded conductor for earth continuity conductor and connected to earth dolly and to be terminated in (1.6) mm thick pressed steel terminal boxes/ on PVC Boxes (concealed type in permanent bldg and surface in temporary bldg or as directed ) for mounting fittings like switch, socket, fan regulator etc. with 3 mm thick laminated bakelite sheet cover ,for housing switches, socket outlet, regulator etc. complete all as specified or directed including testing on completion.

All as per item No.127 here-in-before but One 3 pin socket outlet 5/6 Amps on the same board with other switchs with cables 1.5 Sqmm size.

All as per item No.127 here – in – before but for one 3 / 5 -pin switch socket outlet 5/6 amps on independent board.

Supply and fix in replacement switch piano flush button, single pole, 5/6amps, one way all as specified and as directed.

Supply and fix switch piano flush button, single pole, 5/6amps, one way all as specified and as directed.

Supply and fixing in replacement lamp/angle holder insulated body with back plate for batten fitting all as specified and as directed.

Supply and fixing lamp/angle holder insulated body with back plate for batten fitting all as specified and as directed.

S & F in replacement LED retro fit lamp B-22 holder base with poly carbonate body and aluminium heat shrink of 9W complete CAT Part No : LHLDDBEBBI8R009 of havells or Equivalent of Crompton/Philips.

S & F in LED retro fit lamp B-22 holder base with poly carbonate body and aluminium heat shrink of 9W complete CAT Part No : LHLDDBEBBI8R009 of havells or Equivalent of Crompton/Philips.

Supply and fix in replacement switch socket combination 2 – in – one, 3 Pin / 5 Pin, 5/6 amps flush type all as specified and as directed.

Supply and fix switch socket combination 2 – in – one, 3 Pin / 5 Pin, 5/6 amps flush type all as specified and as directed.

Supply and fixing in replacement switch socket combination 2 – in – one 6 Pin , 6 / 16 amps flush type universal all as specified and as directed.

Supply & Fixing in replacement ceiling rose surface bakelite 65 X 50 mm three terminal all as specified and as directed.

Supply & Fixing ceiling rose surface bakelite 65 X 50 mm three terminal all as specified and as directed.

Supply and fixing in replacement LED tube lights fitting, 4 feet long 1x 18W, 220V, AC decorative box type with holder including Removable poly cabonate LED tube light with inbuilt driver connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

Supply and fixing LED tube lights fitting, 4 feet long 1x 18W, 220V, AC decorative box type with holder including Removable poly cabonate LED tube light with inbuilt driver connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete including taking down old unserviceable fitting complete all as specified and as directed.

Supply and fixing in replacement LED building security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and as directed.

S & F LED light fitting 1x9W/1X10W IP66 & IK09 integral LED Bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size including taking down old unserviceable fitting complete all as specified and as directed.

S & F LED light fitting 1x9W/1X10W IP66 & IK09 integral LED Bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size including taking down old unserviceable fitting complete all as specified and as directed.

S&F metal plug socket single pole and neutral encloser with two pin earth plug with 01 No MCB SP 20 Amp, C series complete all as specified and as directed.

S&F metal plug socket single pole and neutral encloser with two pin earth plug with 01 No MCB SP 20 Amp, C series concealed in wall complete all as specified and as directed.

S&F in repair Sheet metal enclouser Double door for MCB DB,s Phosphatised Powder Painted with bus bar 200 Amps rated Single pole and neutral linkof 8 way 240 Volts AC, concealed in wall complete all as specified and as directed.

Supply and fixing Sheet metal enclouser Double door for MCB DB,s Phosphatised Powder Painted with bus bar 200 Amps rated Single pole and neutral linkof 4 way 240 Volts AC concealed in wall complete all as specified and as directed.

Supply and fixing in replacement amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of SPN 40 to 63 AMP and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and as directed.

Supply and fixing amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of SPN 40 to 63 AMP and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and as directed.

Supply and fixing in replacement amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of SP 5 To 32 AMP and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and as directed.

Supply and fixing amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of SP 5 To 32 AMP and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and as directed.

M&L in repairs for sub main wiring along with earth wire of size two run of 4 sq mm + one run of 4 Sq mm earth wire single core PVC insulated cable with stranded copper conductor FRLS including drawing into 25 mm rigid non-metalic PVC casing caping on surface of wall/roof .(Note Three run of 4 Sqmm including one run of 25 mm of size casing caping shall be measured as one unit length including taking down of old servicible sub main wiring.

M&L for sub main wiring along with earth wire of size two run of 4 sq mm + one run of 4 Sq mm earth wire single core PVC insulated cable with stranded copper conductor FRLS including drawing into 25 mm rigid non-metalic PVC conduit concealed in wall/roof .(Note Three run of 4 Sqmm including one run of 25 mm rigid non-metalic PVC conduit shall be measured as one unit length, complete all as specified and as directed.

Supply and Fixing exhaust fan, steel body AC single Phase. 230V of size 380mm sweep with, blades, and frame and louvers complete all as specified and directed by Engr-in-Charge.

Supply and Fixing exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and louvers complete all as specified and directed.

Supply and fixing ventilation fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm complete.

Supply and fix in replacement electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc including taking down old u/s Geaser & deposit to MES Store complete all as specified and directed by Engr-in-Charge.

Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc complete all as specified and directed.

Earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm buried directly in ground ( earth pit not less than 2.25 m deep bellow ground level ) with top edge of the plate not less than 1.5 m bellow normal ground level, connected to galvanized earth lead wire 4 mm dia. by means of galvanized iron or steel bolts , nuts , check nuts and washers, and connected to equipments as directed , including funnel with GI med grade watering pipe 20 mm bore , wire mesh , charcoal or coke and common salt in alternate layers of 15 cm compacted thickness all around the earth electrode , with concrete pit in PCC (1 : 3 : 6) type C-1 , 50 mm thick pre cast RCC (1 : 2 : 4) type B-1 cover slab reinforced with 8 mm dia deformed bar 15 cm C/C and suitable handle of 10 mm dia round bar ,GI medium grade pipe for earth lead protection including necessary excavation earth work in soft/loose soil and disposal of spoil to a distance n.exc. 50 m and necessary testing complete all as shown on electrical plate No. 5 of MES SSR Part-I and as directed.

Earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm buried directly in ground ( earth pit not less than 2.25 m deep bellow ground level ) with top edge of the plate not less than 1.5 m bellow normal ground level, connected to galvanized earth lead wire 4 mm dia. by means of galvanized iron or steel bolts , nuts , check nuts and washers, and connected to equipments as directed , including funnel with GI med grade watering pipe 20 mm bore , wire mesh , charcoal or coke and common salt in alternate layers of 15 cm compacted thickness all around the earth electrode , with concrete pit in PCC (1 : 3 : 6) type C-1 , 50 mm thick pre cast RCC (1 : 2 : 4) type B-1 cover slab reinforced with 8 mm dia deformed bar 15 cm C/C and suitable handle of 10 mm dia round bar ,GI medium grade pipe for earth lead protection including necessary excavation earth work in soft/loose soil and disposal of spoil to a distance n.exc. 50 m and necessary testing complete all as shown on electrical plate No. 5 of MES SSR Part-I including taking down existing and as directed.

Material and labour for cable XLPE insulated screened PVC bedded, galvanised steel strip or wire armored, electric power cables (heavy duty 1100 Volts grade with stranded aluminium conductor of size 16Sqmm 2 Core, including glands, lugs, nut, bolts, washers as required at site, testing including taking down complete all as specified and directed.

Material and labour for cable XLPE insulated screened PVC bedded, galvanised steel strip or wire armored, electric power cables (heavy duty 1100 Volts grade with stranded aluminium conductor of size 10Sqmm 2 Core, including glands, lugs, nut, bolts, washers as required at site, testing complete all as specified and directed.

Sand cushioning to underground cables provided with a layer of sand 8cm thick before laying the cable in trenches and 15cm thick after laying the cable in trenches complete all as specified.

M&L Sub class ‘B’bricks for covering to cable laid dry flat ,with width equal to the length of brick.

S & F Steel pipe glavanized light grade of 40 mm dia laid in trenches or under ground/floor or road of fixed with pole for protection of cable/ Earth sstrip including clams with bolts nuts and wasers complete ass as specifed.

M&L for GI tubing 25 mm dia Medium grade with all fittings laid in trenches or fixing in wall, all as specified an directed.

M&L for GI tubing 20 mm dia Medium grade with all fittings laid in trenches or fixing in wall, all as specified an directed.

Supply and Fix Rotational moulded poly-ethylene water storage tanks (cylindrical vertical closed top) 750 Lts Capacity icluding suitable outlet tank ipple and locking arrangements hoisted and fixed in position all as specified and directed.

Cutting , screwing, threding and fixing GI tubing for alteration or addition size of 25/ 23 mm dia GI tubing all as speciied and directed by engr in charge.

S&F for Gun metal gate valve, with iron wheel head, screwed both ends for iron pipe and fixed suitable for 25 mm dia GI tubing all as specified.

S&F for Gun metal gate valve, with iron wheel head, screwed both ends for iron pipe and fixed suitable for 20 mm dia GI tubing all as specified.

Framework of water tanks and similar work conforming to Fe.290.Gde-E-165 painting with two coat of black bituminious paint over a coat of red oxide primer complete all as specified and directed.

M&L for cement concrete (1:3:6) type C-2 (using 40 mm graded crushed stone aggregate) as in foundation, filling and mass concrete including finished even and smooth (without using extra cement complete all as directed.

M&L for PCC (1:2:4) type C-1 (using 20mm graded crushed stone aggregate) water troughs and the like including weathering, slightly rounded or chamfered angles and throating including extra using waterproofing compound complete all as directed.

M&L forproviding precast cement concrete solid block masonry over 10cm in width and setting in mortar 1:6 using pre cast cement concrete block (1:3:6) type C-1 using 20mm graded stone aggregate complete all as specfied and directed.

S & F of PVC float valves high pressure with polythene float and flynuts complete screwed for iron pipe or PVC ferrule and fixed of size 25mm bore in repairs.

Note: In case doubling/duplicancy of BOQ items , the lowest quoted rate shall be applicable for payment.

RAMESH GURUNG (BID ID -3103552)

MS BRAHMA CONSTRUCTION (BID ID -3104160)

PRASAD PRADHAN AND SON (BID ID -3104122)

GYANENDRA THAPA (BID ID -3104223)

G K SUTHAR (BID ID -3104125)

MS MAYA PRAKASH GOEL AND SONS (BID ID -3103588)

HEM RAJ GURUNG (BID ID -3104201)