SPECIAL REPAIR OF BLDG NO P 187 AND P133 OFFICE BLOCK AND LAO OFFICE AT COD UNDER GE NORTH DELHI CANTT 10

Amount

Demolition of reinforced cement concrete (reinforcement cut as required to facilatate demolition) of any description and in any position not otherwise specially provided

M&L Reinforcement cement concrete 1;2:4 tye B-1 using 20 mm graded crushed stone agg as in Chajja complete all as specified and directed

M&L for Reinforcement cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in beams, cantilevers bressummers, lintels over 1.5m span all as specified and directed.

M&L Reinforced cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate in Slabs supported on walls,beams and columns in floors,roofs, landings, balconies,canopies, deck slabs and in shelves and the like complete (reinforcement to be measured separately).

Use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lilntels, cantilevers, shelves inclusing supports, overhangs, etc, also splays between floors and beams, etc.

Use and waste of formwork to sides and soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; n. exc. 200 mm thick (Horizontal or slopping) and similar works rough finished surfaces of concrete complete.

Formwork to chullah hoods, chajjas, troughs & similar items including edges rough finished surfaces of concrete ( flat ) complete all as specified and directed.

TMT bars 6 mm to 8 mm dia cut to length, bent to shape required incl crancking bending and hooping ends for stirrups all as spd and directed.

TMT bars10 mm dia and over cut to length, bent to shape required incl crancking bending and hooping ends all as spd and directed.

Demolition of cement concrete (unreinforced) of any description and in any position not specifically provided for complete all as specified and as directed.

M&L Water proofing treatment walls of bathroom consisting of the following operation including demolition/taking down old treatment :- (i) Cleaning of surfaces by wire brushing brooming removing dust particles (ii) Filling of all brick joints with cement mortar 1:4 (iii) Applying a coat of Chemical Dr fixit Pidifin 2K (iv) applying fiber mesh setting with chemical Dr fixit Pidicrete URP (v) final coating with Pidifin 2K and sprinking of sand (vi) After the surface dried, plaster the surface with CM 1:4 15 mm thick. (Note All water proofing treatment will be executed by the authorised representative of Dr fixit).

M&L Water proofing treatment on sunken floor consisting of the following operation including demolition/taking down old treatment :- (i) Cleaning of surfaces by wire brushing brooming removing dust particles (ii) M & L PCC 1:2:4 type (Bo) using 12.5 mm graded stone aggregate 50 mm thick, finishing the surface even and smooth without using extra cement (iii) Applying a coat of Chemical Dr fixit Pidifin 2K (iv) applying fibe mesh setting with chemical Dr fixit Pidicrete URP (v) final coating with Pidifin 2K and sprinking of sand (vi) After the surface dried, screeding the surface with CM 1:4 15 mm thick including finishing even and smooth using extra cement. (Note All water proofing treatment will be executed by the authorisedrepresentative of Dr fixit).

M&L for lean concrete 1:5:10 with broken brick aggregate in sunken of gauge n exc 63mm deposited spread and levelled in layers n exc 15 cm thick hand rammed to a true surface

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

Roughening surfaces of old concrete floor by picking sweeping clean and washing down with water to remove dust, etc

M&L Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match. over screed bed or bedding layers of cement mortars 15 mm thick in CM 1:6 all as specified and directed.

Ditto- item No. 16 above but as in vertical surfaces such as skirting/ dado over and including 10 mm thick rendering in CM (1:4) compelete.

M&LVitrified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over screed bed or bedding layers of mortars 15 mm thick in CM 1:6 all as specified and directed.

Ditto- item No. 18 above but as in vertical surfaces such as skirting/ dado over and including 10 mm thick rendering in CM (1:4) compelete.

M&L for non skid ceramic digital coloured tiles 7 to 8 mm thick joint free area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement. all as and directed screed bed or bedding layers of mortars 15 mm thick in CM 1:6 all as specified and directed.

M&L Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match incl rendering 10mm thick in CM (1:4) and finished rough, complete all as spd & directed.

M&L for 75mm thick type C-2 1:3:6 (using 40mm graded stone aggregate) as in sub base to receive stone slab and pavement all as specified and directed.

M&L Granite 18-20 mm thick colour as approved ( of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms or making hole for fix in oveal shape for fixing of wash hand basin and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shed of granite over 15mm thick screed bed in cement mortar 1:6) including moulding and polishing the edges all as specified and directed

M&L Granite 18-20mm thick colour as approved ( of any type) work (table rubbed and polished) in for wall lining (veneering to wall) 12 mm thick in cement mortar (1:3) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shed of granite including moulding and polishing the edges etc complete.

M&L for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc, including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc, of required size, on the top of floor or the side of waist slab with suitable arrangement inculding taking down of done.

Dismantling boarding any description fixed in any position, and any thickness all as specified and directed.

S&F 5 mm thick prelam PVC sheet in striips & channel feathered at the edges for fixing on Solild PVC wall Lining Insulated PVC Wall Lining, and Solid PVC partitioins inclusive of solvent cement and fixing at site.

S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC frame as per specification and drawing

Demolition of brick work or stone builder masonry, built in cement or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stone work and precast concrete articles complete.

Dismantling of RCC jali as in walls including taking out debris etc out of MOD area all as specified.

M & L Brickwork with subclass 'B' Brick straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

Ditto- item No. 32 but except brick complete.

M&L for brickwork with subclass 'B' bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 all as specified and directed.

M&L for Preventive treatment against the danger of carbonation in exposed faces of wall:- (i) Cleaning existing surfaces of RCC members and making surface free of loose material, oil, grease etc. by vigorous wire brushing including light grit blasting where necessary as recommended by Engr-in-charge. (ii) Further, cleaning using biocide(as recommended by manufacturer) to ensure that surface is free of algae and fungus and no trace of paint (any type) left out. Sand blasting to be done to remove trace of paint. (iii) Cleaned surface to be allowed to dry. (iv) Spray a coat of primer (as recommended by manufacturer) over dry cleaned surface as required prior to final finish. Primer shall be diluted in proposition 2:1 with mineral turpentine. After application, primer shall be allowed to dry for 03 hours or as directed. (v) Apply a coat of neat Aliphatic Acrylic anti-carbonation (ACC) over the primed surface with air / spray gun at nominal rate of 3.5 ltrs per Sqm as recommended by manufacturer. (vi) Apply a more coat of Aliphatic Acrylic anti-carbonation (ACC) after 5-6 hours as recommended by manufacturer complete all as specified and directed.

M&L for followings :- (i) Removing plaster & finishes all around the coloumns, slabs & beams (on all four sidescription of column to full height , three sidescription of beam to entire span & bottom of slab to area as directed) (ii) After cleaning gently removing cover concrete using pneumatic/electric chipper or any other approved tool in entire portion of structural member (removal of cover concrete shall be done to an extent when reinforcement is visible) (iii) Removal of cover concrete with under cutting of up to a depth of 20mm beyond reinforcement around full circumference & full length of bar where directed. (concrete shall be stripped to an extent concrete substrate is exposed) (iv) Cleaning exposed concrete substrate by using water jet. (v) Removing visible rust along the length of reinforcement using hand tools as approved. (The Engr-in-charge may order sand blasting if rust is approved) (vi) Any other work as directed by Engr-in-charge to present clean surface for determination of type of repair to be carried out complete all as specified and directed.

M&L for providing rust proof /anti corrosive treatment to bars :- (i) cleaning of all exposed bars (new & old) alround (ii) Apply a single coat of Alkaline rust converting primer on alround bars new & old as recommended by the manufactuer (iii) Apply two coats of Epoxy phenolic anti corrosive protective coat on bars alround new & old as recommended by the manufactuer. Note : Anti corrosive treatment shall be continuous espcially in the regions where pitting, imperfections, etc were present on the surface of the bars. It is important that the rear portions of re bars (those towards the concrete substrate) should not be left without coating.

M&L for providing PMM (Polymer modified cementitious mortar) :- (i) Dry sub strate surface and free of debris & dust (ii) Applying Epoxy bond coat on the sound substrate using approved spray machine & ensuring that no pin holes are visible.(In case pin holes are still visible after a coat, a second coat shall be applied to ensure absence of pin holes). (iii) Immediately after application of epoxy bond coat as above apply PMM (Polymer modified cementitious mortar) of 25 mm thickness. Note:- Application of PMM shall be preferably be in coats of appx 10mm thickness. PMM work shall be executed in fairely rapid successions so as entire work is completed with in 30 mins). PMM shall be pre packed ready to use. (iv) PMM surface to be moist cured for three days followed by air curing in temperature as recommended by manufactuer complete all as specified and directed.

M&L for treatement of cracks found in the core concrete :- (i) Opening of crack by making a ' V' notch/groove of size 12mm x 12mm over the entire length of the crack as identified by the Engr-in-charge. (ii) cleaning ' v' notch/groove of all dust/debris/loose material (iii) Drilling hole of 16mm dia and about 40mm deep along the length of crack @ (300 mm c/c or thickness of structural member whichever is less) Note : In case length of crack is found less than 300 mm then min 2 holes shall be drilled. (iv) Inserting 12 mm dia flexible PVC one way injection nipple in the hole drilled above and fixing the nipple with the help of fast setting epoxy putty. (v) Seal the surface around the nipple and the area of crack between successive nipples polymer modified mortar to ensure that there is no leakage from any gap. (vi) Allow the polymer modified mortar to cure for 24 hours and ensure that firmly fixed in postion. (vii) Cleaning nipple one by one commencin from the top to bottom in case of column and one by one in alternate direction incase of beam/slab using blow compressed air followed by water injection. An Ensuring that there is no obstruction in free flow of grouting materials complete all as specified and directed. (viii) Injecting " resin with very low viscosity monomer by mixing resin and hardener in proportions recommended by manufacturer by using injection gun equipped with pressure gauge & valves for controlling of flow of compressed air & resin. Note:- pressure shall be in the range of 1-2 kg/Sqm and shall be done in nipples one by one as per order recommended by manufacturer. Mixing of resin and hardenere shall be mixed in small quantities so as it is consumed with in 30 minutes. Before use mixer shall be stirred thoroughly. (ix) Allow entire effected surface to cure for 24 hours. (x) cutting out projected parts of the nipple & seal the hole in the nipple with epoxy putty as recommended by manufacturer. (xi) cleaning exposed surface complete all as specified and directed.

S&F 12mm dia steel sheer connector in grid pattern in between old core and new concrete as wherever directed by Engr-in-charge and as specifed by manufactuer including drilling hole of depth of 100 mm and chemical anchoring with pure epoxy resin anchoring complete all as specified and directed. (Note:- The cost of drilling hole &chemical anchoring with epoxy resin is inclueded in this item)

M&L for Providing & Pouring Micro concreting M-40 grade :- (i) Dry concrete substrate surface and free of debris & dust (ii) Applying Epoxy bond coat on the sound concrete substrate using approved spray machine & ensuring that no pin holes are visible. (In case pin holes are still visible after a coat, a second coat shall be applied to ensure absence of pin holes). (iii) Immediately after application of epoxy bond coat as above pour Micro concreting M40 grade using approved mixing machines/pumping under pressure via approved pneumatic pump at the locations to be repaired in RCC beams & columns etc,. Adding of aggregates will be permitted only as per manufacturer’s recommendation without compromising the strength. The rate shall include cost of all materials (except re-bar) labour charges for demolition of the column and beam, chajja, mixing, pouring concrete, cost of tools, lead & lift of materials, transportation etc., to carry out the complete work complete all as specified and directed. Note : The cost of micro concrete M-40 grade & Epoxy bond coat is inclueded in this item.

M&L for Drilling & chemical anchoring of new rebars/stirrups :- (i) Drilling in to the sound RCC members for anchoring of rebars/stirrups as directed, the dia of hole to be match with dia of rebar & length of drilling as under :- 8 mm dia bar - drilling length 80 to 100 mm Note : Anchoring of new re-bars of any dia as directed in to the sound RCC members as directed using pure epoxy resin anchoring mortar with appropriate diameter of drilling of holes as mentioned above for proper bonding into the concrete etc., complete all as specified and directed. Note:- The cost of drilling hole & chemical anchoring with epoxy resin is inclueded in this item

M&L for Drilling & chemical anchoring of new rebars/stirrups :- (i) Drilling in to the sound RCC members for anchoring of rebars/stirrups as directed, the dia of hole to be match with dia of rebar & length of drilling as under :- 16 & 20 mm dia bar - drilling length 160 to 180 mm Note:- Anchoring of new re-bars of any dia as directed in to the sound RCC members as directed using pure epoxy resin anchoring mortar with appropriate diameter of drilling of holes as mentioned above for proper bonding into the concrete etc., complete all specified and directed. (The cost of drilling hole & chemical anchoring with epoxy resin is inclueded in this item)

M&L for use & waste of form work using steel sheets , steel bracing, propping etc around structural members where micro concreting to be done and keeping form work in position till required specified period complete all as specified and directed. Note:- Form work shall be 100% leak proof. For purpose of payment area in touch with concrete shall be measured.

S&F for stengthening existing reinforcement by use of mild steel bars of any dia , cut to length, bent to shape required, including cranking, bending spirally and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for chipping of spalled and loose concrete and cleaning rust from re-inforcement by sand brushing scrubing down concrete surfaces with wire brushes cleaning with water allowed to dry applying a layer of zinc rich epoxy primer as antirust on all exposed reinforcement followed by a layer of bonding coat of a layer of epoxy adehessive on complete exposed surfaces of concrete and provide guniting in two layers over steel welded mesh 2 mm dia of wire and total aperture 75 mm, thickness of gunite n.exc 25 mm thick (average thickness) using cement mortar 1 :3 with OPC 43 grade cement mixed with polycrete admixture @ 2 % by wight of cement or as per manufactures instructions and finally applying cement plaster over gunite surfaces of required thickness to give an even uniform and smooth finish conforming to proper Geometrics in cement mortar 1:4 to match with the existing surface as in side and soffits of slabs,chajjas,fins,facias ,parapets ,columns and beams etc complete including necessary scaffolding ,shuttering necessary chased to brick work or RCC members at any height upto four storey buildings incl removing of small trees shrubs etc all as specified(Note: steel welded mesh to be welded with the existing reinforcement. The cost of welded meshis to be welded with the existing re-inforcement is deemed to be included in the quoted rate complete all as specified and directed.

Taking down existing cement plaster including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

Removing old lime wash or other treatment exposed brick face, hacking for key, raking out joints of old brick work or stone work built in lime, cement mortar or mud mortar; not previously plastered; and scrubbing down with water etc. to receive plaster

M&L 15 mm thick Ready mix plaster (Make:- Ultratech readiplast /Birla Aerocon RMP /ACC Suraksha RMP ) on brickwork or concrete surfaces of wall (internal surface )finished even and smooth complete all as specified and as directed by engr-in-charge.

M&L 15 mm thick Ready mix plaster (Make:- Ultratech readiplast /Birla Aerocon RMP /ACC Suraksha RMP ) on brickwork or concrete surfaces of wall (external surface )finished even and smooth complete all as specified and as directed by engr-in-charge.

M&L 5 mm thick Ready mix plaster (Make:- Ultratech readiplast /Birla Aerocon RMP /ACC Suraksha RMP ) on brickwork or concrete surfaces of wall (ceiling )finished even and smooth complete all as specified and as directed by engr-in-charge.

M&L for Preparing new plastered or unplastered surfaces of ceiling and applying three coats of white wash complete.

M&L for complete removal of old treated of ceilling surfaces and preparing of undecorated plastered surfaces of ceiling and applying two coats of white wash complete.

M&L for Preparing new plastered surfaces of wall and applying two coats of oil bound distemper white or tinted over and including a coat wall care putty and chalk whiting on plastered surfaces preparatory to distempering complete.

M&L for Complete removal of existing treatment, nails etc and preparing old decorated surfaces of wall and applying two coats of Oil Bound distemper over a coat of wall care putty complete all as specified and directed

M&L for finishing walls with acrylic smooth exterior paint of reqired shade; New work (Two or more coat applied @ 1.67 ltr/10Sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 Sqm

Taking up or down steel tubing and connections 15 mm bore complete.

Taking up or down steel tubing and connections 20 mm bore complete.

S&F Steel water tubes, medium grade, ISI marked, galvanised, 15 mm bore with all fittings, fixed to walls and ceiling or laid in floors complete.

S&F Steel water tubes, medium grade, ISI marked, galvanised, 20 mm bore with all fittings, fixed to walls and ceiling or laid in floors complete.

Refixing only old 15 mm dia bore steel water tubing & connection in new or old position fixed to wall, ceiling or laid in floors including necessary cutting & making of new threads for fixing of new fittings such as elbows, tees, sockets, union, reducer, etc as required complete.

Refixing only old 20 mm dia bore steel water tubing & connection in new or old position fixed to wall, ceiling or laid in floors including necessary cutting & making of new threads for fixing of new fittings such as elbows, tees, sockets, union, reducer, etc as required complete.

Dismantling PVC water tanks of capacity exceeding 250 litres but not exceeding 500 litres including ball valves complete.

Dismantling PVC water tanks of capacity exceeding 500 litres but not exceeding 1000 litres includng ball valves complete.

S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of 500 litres capacity, ISI marked, double layered hoisted and fixed in position including connecting up pipes complete.

S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of 1000 litres capacity, ISI marked, double layered hoisted and fixed in position including connecting up pipes complete.

S & F in repair 20 mm Gun-metal, globe or gate valves,with iron wheel head, screwed both ends for iron pipe and fixed complete.

S & F ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic wall, screwed for iron pipe and fixed for 25 mm bore size (Minimum weight 210gms), complete.

Cutting chases in brick walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, shelves, lintels, etc, and cutting chases for concealed water tubings or conduit wiring, etc and making good, cutting not exceeding 10cm girth complete.

Demolition/taking down PVC/CI drain/Rain Water Pipe under floor or wall of internal dia 75/100 mm, set in cement mortar/ Bricket complete incl fittings.

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls 75mm bore complete.

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls 110 mm bore complete.

S&F PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches or in floors, 75 mm bore complete.

S&F PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches or in floors, 110 mm bore complete.

Dismantling cast iron pipe , jointed in cement mortar of dia up to 100mm. all as specified.

S&F cast iron soil, waste and vent pipes (sand cast) 100mm bore in any length with or without ears with cement joints laid in trenches all as specified.

All as per srl item 76 above but 75mm bore pipes ditto.

S&F cast iron soil, waste and vent pipes (sand cast) 100mm bore in any length with or without ears with cement joints fixed to walls complete all as specified and directed.

All as per srl item 78 above but 75mm bore pipes ditto.

S&F Cast iron bend (any radius) diminishing pieces or tapers 100mm bore fitted with oval access door all as specified.

S&F Cast iron bend (any radius) diminishing pieces or tapers 75mm bore fitted with oval access door all as specified..

Demolition of cement concrete in ground floors and pavings any thickness (below or above ground level)

M&L for 75mm thick PCC (1:4:8) type D-2 (using 40mm graded stone aggregate) as in sub base / flooring complete;

M&L machine pressed precast rubber mould coloured concrete paver blocks of 60 mm thick any shape and size conforming to IS 15658-2006 ,M-35 grade with grey cement and no pigment complete all as specified and directed.

40mm thick Sand filling under floors or in Foundation including watering & consolidation etc complete all as spd.

S&F PVC (SWR) bends any radius, 110 mm bore, complete.

S & F in repair Soap Dish Holder. Make Jaquar or equivalent all as specified and directed.

S&F in repair 75 mm PVC (SWR) floor trap, plain with grating with or without hole including jointing with solvent cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate mix with WPC complete all as specified and as directed.

S & F in repair Glass shelf 600 mm long. Make Jaquar or equivalent all as specified and directed.

S & F in repair Corner glass shelf (with bracket). Make Jaquar or equivalent all as specified and directed.

M & L for writing letters (Block, Roman, Italic or Indian) n exceeding 30 cm high ( for writing Bldg No, Name, Rank and Unit of individual officer occupaying the md accn inclluding cost of scaffolding )

S & F in repair Tubular towel rail of brass chromium plated, 20 mm dia, 'D' type, 60 cm long between flanges complete.

S & F in repair Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, fancy type, chromium plated, with long shank and cup (concealed type) screwed both ends for iron pipe or for unions 15 mm bore complete.

S&F in repair of quarter turn bib tap make of Jaquar or Mark/Kohler with wal flange for iron pipe of size 15mm bore chromium plated all as specified and directed.

S & F in repairs 15mm dia bore central hole wash hand basin mixer .

S & F in repairs wall mixerss with provn for over head showers with 115 mm long bend pipe on upper side connecting legs and wall flanges all as specified and directed.

S&F in repair CP towel rack with 3 nos hooks, 600mm long superior quality fancy type as approved by EIC complete all as specified and directed.

S&F in repair fancy type brass chromium plated shower rose with arm complete.

S&F in repair 10 litre capacity PVC low level flushing cistern with dual flush type‘ white’ with inlet, float valve including bracket with 32mm dia PVC waste/flush bend pipe appx 600 mm long complete.

S & F in repair PVC connection pipe 600mm long and15 mm dia with brass fly nut at both ends complete.

S&F in repair vitreous china squatting pan, ‘Orissa’ pattern, of size 580 mm x 440 mm white with integral foot rest complete including provn of cement concrete bedding and connection to trap, outgoing flushing pipe, anti syphonage pipe etc complete. Make - Cera/Jaquar/Kolar

S&F in repair Vitreous china wash down water closet pan (pedestal pattern), white including fixing bolts, flushing cistern and flush pipe connection to trap and to flushing pipe inbend cluding provn of cement concrete beading complete all as specified and directed. Make - Cera/Jaquar/Kolar

S&F in repair EWC Seat cover Black/white colour as approved of PVC closed pattern with flat bottom and mild steel lchromium plated or aluminised hinging device complete all as specified and directed. Make - Cera/Jaquar

S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified

S&F in repair Viitreous china premium/1st quality wash down water closet wall hung EWC white/ivory/off white (closed pattern incl seat cover and all necessary accessories like rag bolts/gel gasket etc, (excluding flushing cistern & flush pipe) complete in all respect all as specified. Make - Jaquar/Kohler/Cera

S&F in repair Vitreous China valveless, syphonic action type, flushing cistern, with dual flush bottons of capacity 10 ltrs low level, white, with inlet, ball valve, float and handle including brackets and flush pipe. Make - Jaquar/Kohler/Cera

S&F in repair vitreous china urinals bowl, half stall flat back large of size white with grating and union for discharge pipe complete including waste coupling provide and fixing plugs bedding urinal against wall in CM 1:2 securing urinal to plugs with and including 60mm long brass screws pointing around urinal back in cement including Urinal spreader complete all as specified. Make - Jaquar/Kohler/Cera

S&F in repair table top wash basin white, flat bottom size 525x415x140mm of make Jaguar or equvalent excluding tap, chain, plug but including brackets, waste fitting 32mm dia brass chromium plated push type coupling with long screwed shanks and fly nuts flange end bedded in red lead cement and other end fixed complete all as specified and directed.

S&F in repair brass Chrome Polished comfort height single-control operation allows hot and cold or mix both .

S&F in repair Chrome Polished brasss urinal spreader 15mm inlet with fixing stud from Cera with necessary fixing arrangement

S&F in repair CP Stainless Seel Connection pipe 600mm long pemimum qualilty for Gyser, urianal, WHB etc

S&F in repair CP towel ring.

S&F in repair CP Toilet Paper Holder with cover (Silver) .

M&L cement concrete type C-1, 1:3:6 (using 20mm graded aggregate) as in plinth protection and paving 75mm thick laid in slope finished even and fair without using extra cement incl making joints at every 2.5m and at corner filled with bitumen 85/25 and sand in ratio 1:2 by weight including necessary form work and complete all as specified.

S & F 32 mm dia bore Low density polyethylene pipes (LDPE)of pressure rating 6kgf/cm2 fixed complete to walls,ceilings or in floors etc for WHB and sink complete.

S&F in repair Chromium plated brass angle valve including cp flanges for 15mm bore pipe, complete all as specified and directed.

S&F in repair, two way angle valve cock chromium plated brass fancy type including cp flanges bore 15mm complete all as specified and directed.

S&F in repair brass Chrome Polished mixture comfort height single-control operation allows hot and cold or mix both

S&F for aluminium anodized grills with 6 x 5 mm aluminium section having square gap of 50 mm thick with fixing rails of channels 12-15 mm complete all as directed.

Taking down chowkhats or frames n.exc 1.50 sqm with shutters (without taking off shutters from the frames) all as specified and directed.

Taking down chowkhats of frames exc 1.50 sqm but n. exc 4.0 sqm with shutters (without taking off shutters from the frames) all as specified and directed.

S&F Solid PVC moulded door frame of size 50mm x 95mm made out of 5mm single side prelam PVC sheet used instead of plain colour PVC Sheet suppling & fixing in opening as per specification & drawing.

Factory Made Solid PVC Moulded Door Shutter with partical board, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm Plain colour PVC Sheet on back face, supplying & fixing in frame at site as per specification & drawing in SSR

S&F factory made three track UPVC sliding windows white in colour or as approved made of extruded profiles with wall thickness of 2.3mm ((+/- 0.20mm) Windows profiles with hollows section with multichamber. Frame size (88mmx52mm), Sliding sash (42mm x 67mm), sliding mesh sash (42mmx57mm), sliding interlock(one vertical length in each shutter) 45.5mmx28mm), glazing bead (24.5mmx16mm) will be mitered cut and fusion welded at all coeners, including drilling of holes for fixing of hardware and drainage of wateretc, making arrangement for fixing of hardware, EPDM, gasket, 1.2+/-0.20 mm thick galvanised steelframe (30mmx28mm) 2 Nos sliding sash (30mmx18mm), sliding mesh (26mmx10mm), profile to be inserted in required profile frame will be fixed to the wall with 8mm x 100mm long fastener hardware, (Touch lock of zinc alloyed (white powder coated), steel roller system stainless steel wire 0.36mm nominal dia of wire and average width of aperture 1.40mm, aluminium grill and required accessories), Note - The unit rate quoted by contractor excludes cost of glass and includes all another connected accessories i.e. wire mesh and hard wares, complete all as specified and directed. .

S&F casement windows with net & MS Grill single or multi shutter turn window are made out of UPVC multi-cavity frames sections of 60x60x2.5mm suitably reinforced and double mult-shutters division are made by using sash mullion having 50x64x2.5mm multi-cavity UPVC section, suitably reinforced with GI and shutters are made out of 50x85x2.5mm UPVC section, reinforced and welded in corners with EDPM gaskets provision for glass and for air tight at frames and outer side of shutter with single glaze window shutters using suitable glass bead with perfect hardware like hinges handles, stays etc complete. Mosquito mesh shutter is made out of UPC extruded section of 61x27x2mm with GI channel of 1.2mm thick, welded in corners. Stainless steel wire mesh (Mosquito net) to be fitted in shutter with proper required accessories like hinges, MS grill of 12mm round or square bar are inserted in main frameas guard bar & screwed by hidden screwing system with powder coating and filled the gap between wall and frame with weather proof silicon sealant over backer rod of required size and of approved quality etc complete all as specified and directed. Note - (Glazed shutters float glass thickness not less than 4.00 mm and wiremes shutter with stainless steel wire mesh 0.36 mm dia with aparature 1.4 mm shall also be deemed included in quoted rates and No extra payment will be made separately). Make/Manufactruer; Fenesta/Winkraft/Yashpoly/Duraplast/Accura (Accucel).

S&F UPVC ventilators made out of UPVC multi-cavity frames sections of 60x60x2.5 mm UPVC section, reinforced and welded in corners with TPE gaskets provision for glass and for air tight at frames and outer side of shutter with single glaze window shutters using suitable glass bead with perfect hardware like hinges, handles, stays etc complete. with MS grill of 12mm thick round/square shape bar duly painted with oil paint over a coat of red oxide are fabricated as per manufactruer and installed in UPVC frame section of 35x35x2 mm by drilling and surveying system filled the gap between wall and frame with weather proof silicon sealant over backer rod of required size and of approved quality complete all as specified and directed (Note - The unit rate quoted by contractor included glass pan and stainless steel wire mesh, and MS Grill etc all as specified and directed. Make/Manufactruer; Fenesta/Winkraft/Yashpoly/Duraplast/Accura (Accucel).

S&F roller blinds premium korean fabric/zebra roller blinds or as approved to windows/opening including top and bottom frame/rail complete all as specified and directed

S&F 10mm thick toughned frosted glass for frame less door shutters of size area exc 1.50 Sqm but n.exc 3.00 Sqm each including double floor door spring hydraulically regulated, and fixed with pivote on top . including CP fittings and fixtures CP handles hinges. CP locking arrangement necessary cutting & holes moulding and fixed in position complete as specified and directed by Engr-in-Charge.

S&F 10mm thick toughened glass as in partition including diamong edging all sides eatching lining and monograme area n exc 0.50 sqm each by sand blasting, including CP 'L' or 'U' heavy duty clams suitable for fixing of glass, min 4 Nos per Sqm all as Spd and directed.

S&F Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass other parts made of mild steel heavy duty.

S&F Door closer hydraulically regulated, Aluminium (Die cast) body designation No 3, universal type suitable for door shutters of 851mm to 1000 mm width and of weight between 61 to 80 kg all as specified and directed.

S&F 4.00 mm thick sheet glass pan ordinary quality and glazing with rubber beading and aluminium glazing clip/patti area n.exc 0.5 Sqm each pan.

S&F 4.00 mm thick figured glass, pin head type glass pan ordinary quality and glazing with rubber beading and aluminium glazing clip/patti area n.exc 0.5 Sqm each pan.

Mild steel conforming to Fe 410-0 or Fe 310-0 in framed work such as grills, gratings, ladder, hinges, door frame, desert cooler stand etc with ends of bars shouldered and/or riveted or forged into spikes; framed guard bars; ladders; railings, coolar stand and similar work complete.

Supply and fix/fabrication in repair cabinet & wardrobe/ cupboard made out of 18 mm thick PVC board plain sheet including providing cabinet complete.

Supply and fix/fabricate in repair wardrobe/ cupboard shutters made out of 15-18 mm thick PVC board one side laminated sheets .

S&F magnetic catches with steel body ‘H’ type, fixed to shutter complete.

S&F 150 mm dia oval shape brass handle cromium plated fancy type polished bright finish

S&F Continuous (Piano) hinges, brass, 30 mm width of flaps (when open).

S&F floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring, fixed to floor of size 140 mm complete.

S&F PVC door stopper fixed with screws in rear side of shutter 75-100mm long.

S&F 100 mm aluminium anodised hasp and staple complete.

S&F 4 levers brass cupboard locks grade-I, size 65 mm

S&F 100 mm long aluminium anodised barrel tower bolts of extruded section and fixed complete

S&F 150 mm long aluminium anodised barrel tower bolts of extruded section and fixed complete

S&F 75mm long stainless steel but hinge in PVC door or FRP doors with screws

S&F aluminium handles 150 mm size cast type, anodised complete PVC door or FRP doors with screws

S&F 200 mm aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast of extruded sections and fixing bolts and sliding bolts of extruded sec or cast aluminium and fixed complete.

M & L applying one coat of synthetic enamel paint on old treated steel surfaces of any description over 10 cm width or girth including preparation of old painted surfaces complete.

M&L applying two coats of synthetic enamel paint on new steel surfaces of any description over 10cm width or girth over a coat of red oxide primer including preparation of steel surfaces complete.

Dismantling of brick tiles, terracing tiles, single layer from roof laid, bedded and pointed in any mortar all as specified & directed.

Demolition of Mud in roofs, any thickness, including plastering and leeping without disturbing RCC roof slab (whether full thickness removed or only a part there of)

M&L PCC 1:2:4 type B0 with 12.5 mm graded stone aggregate with mixing of WPC as in padding over roof slab for making slope on roof top surface.

M&L for 15 mm thick Cement plaster on surfaces of concrete in CM 1:4 on roof surfaces (Over PCC Padding) mixed with WPC complete all as specified and dierected. Note : WPC shall be measured and paid separately

M&L Clearing all the dust, existing roof treatment and loose material by brush/blowe/ Grinder including removing of vegetation/ plantation from the surface. M&L for preparation of roof top surface, providing and applying single component elastic cold applied polyurethane modified acrylic roofing system, co elastic technology (CET) based on modified polyurethane and fully fibre reinforced, having Sun reflectivity index (SR) of 109 on top of concrete roof surfaces. All cracks up to 3mm at corner joints, chaneel and parapets should be treated with crack seal. Applying three coats including one coat of primer of Shali Urethane BTD / Sikalastic 560 / smart care damp proof-ultra having coverage @ min0.75kg/ m2 and dilution up to 10% and laying reinforced fiber net and applying two coats (without dilution) of shaliurethane BTD/ Sikalastic 560 / smart care damp proof ultra @ total consumption 2 kg/ m2 in two coats for shaliurethane BTD/ Sikalastic 560 / smart care damp proof ultra @ total consumption 2 kg/ m2 in two coats for maintaining minimum dry film thickness 1.5mm and elongation at break of free film of approx 350% The materils shall be applied with brush or roller, complete in all respect as per the direction of Engineer-in-Charge/ consultant (Note: 6 Hrs interval between two coat will be maintained). All auxiliary and accessories involved during application should be supplied by single manufacture as a part of system. Make STP/Sika/ Asian paint or equivalent as approved by GE, Note:- Application of water proofing treatment will be done by authorised applicator only. (i) The water proofing treatment shall be carried out by the manufacture or their authorized applicaiton duly approved by GE in writing. (li) 5% amount of the total amount of water proofing treatment shall be retained as a guarantee and shall be released after 10 years. However contractor may deposit the FDR of same amount in favour of GE. If Contractor fail to rectify the defect pointed out during this period in writing, the defect shall be got rectified at contractor risk and cost and the payment shall be made from the amount kept reserved or by encashing the FDR deposited by the contractor as guarantee. The contractor quoted rates for this item shall deemed to be inclusive of this aspect.

Dismantling wall and ceiling board (fibre, pulp insulation etc) or insulation boars/ slabs/ blankets, any thickness, including cover fillets.

S&F false ceiling with semi perforated 12mm thick micro tegular edged at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of size 595x595mm of approved texture, design and pattern having moisture content less than 2% humidity resistance of 99% NRC 0.50 to 0.75 as per IS 8225:1987, Non-combustible as per BS 475 (part-4) -1970 and light Code Description unit rate No 429 Sub Head:26.0 NEW TECHNOLOGIES AND MATERIAL reflectance of 85% minimum to be laid in true horizontal level suspended on interlocking metel T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanised @ 120 grams over sqm including both sides) comprising of main-T runners of size 15x32mm of length 3000mm, cross T of size 15x32 of length 1200mm and secondry intermediate cross T of size 15x32 of length 600 mm to form grid module of size 600x600mm suspended from ceiling using galvanised mild steel items (galvanised @ 80 grams per sqm) i.e 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1000mm length and L shape level adjuster of size 85x25x2mm, Galvanised iron perimeter wall angle of size 24x24x0.40mm of length 3000mm to be fixed on perimeter wall/ partition with the help of plastic rawl pluhs at 450mm centre to centre and 40mm long dry wall screws complete all as specified and directed by Eingineer-in-Charge.

Taking down carefully copper / aluminium point wiring (light / fan socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc for taking credit including making good the disturbed surfaces to match with the existing complete

Material & labour for point wiring concealed type with 1.5 Sq.mm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed FRLS copper conductor cable with and including continuous earth wire of size 1.5 Sqmm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC concealed conduit of 20mm dia or higher, medium grade complete with and including all PVC conduit accessories and modular metal flush box, modular white cover plate with frame, blanking plate etc suitable for up to required module etc complete and making good to the disturbed surfaces to match the existing complete all as specified and directed for for One light / bell point controlled by one, one way switch 06 Amps

All as per above item here-in-before but one Ceiling / exhaust fan point controlled by one, one way switch 06 Amps

All as per above item here-in-before but one 3 pin, 06 Amps socket outlet point on independent board controlled by one, one way 06 Amps switch

All as per above item here-in-before but one 3 pin, 06 Amps socket outlet point on same board controlled by one, one way 06 Amps switch

All as per above item above but point wiring with 2.5 Sqmm single core FRLS cables and earth continuity wire of 2.5 Sq mm single core FRLS cable for one 3 pin 15 Amps socket out let point controlled by one, one way switch on independent board complete all as specified and directed

S&F modular switch, 06 Amps, single pole, one way, 230 volts, one module and IP 20 protection complete all as specified & directed

S&F modular bell push with indicator, 06 Amps, single pole, one way, 230 volts complete

S&F modular switch, with indicator, 16 Amps, single pole, one way, 230 volts complete

S&F modular socket outlet 05 Pin, 06 Amps, 02 module with shutter complete

S&F modular socket outlet 02 in 01, 03 pin, 16 Amps, 02 module with shutter complete

S&F ding dong bell, AC, 230 volts, single pole incl connection complete

S&F ceiling fan regulator, stepped type of 0 to 04 rotary steps, electronic, 02 module, humfree, AC, 230 volts, 120 watts incl connection complete

S&F ceiling rose, 6 Amps, 250 volts, AC, ISI marked with three equal size terminals complete

S&F on surface and wall mounted LED batten with polycarbonate housing and initigarated electronic drive 20 Watt fixture 4 feet provided for efficient heat dissipation with policorbonate diffuser and integrated electronic driver and all accessories pre-wired including connecting up with twin core flat flexible copper conductor cable of suitable size with connector block complete.

S&F surface and wall mounted LED batten 10 watt 2 feet long extruded aluminium housing provided for efficient heat dessipation with polycarbonate diffusser and integrated electronic drive suitable for mirror fittings, all accessories pre-wired including connecting up with twin core flat flexible copper conductor cable of suitable size complete

S&F ultra modern recess mounting 36 Watts, 5700K, 2x2 LED flat panel complete with integrated electronic driver, soft-light and glare free symmetrical illumination, suitable for POP ceilings high brightness SMD LEDs, etc including connecting up with twin core flat flexible copper conductor cable of suitable size with connector block complete

S&F round LED downlighter luminarie, 12 watt, ceiling recess/ surface mounting with integrated driver to delivered superior light output and uniformity utilising the latest LED technology complete

Taking down of existing u/s security light fitting and supply and fixing energy saving security light fitting of 35 watts LED Versatile pressure die-cast aluminium IP 66 roadway luminaire with high power LED as light source comprising with electronic driver and all accessories pre-wired incl connecting up with PVC insulated copper conductor cable 1.5 Sqmm, 3 core and incl light grade GI tube mounting bracket of suitable size & length, bend to shape and fixed to wall by means of 02 nos. of 40 x 5 mm flat iron clamps, nuts, bolts and washers etc complete

S&F exhaust fan, steel body, AC, single phase, 230 V of size 300mm sweep with blades, frame & louver and old/unsv fan to be deposited in E/M store yard complete

-do- but 450mm sweep, heavy duty

Taking down ceiling fan any make from ceiling carefully, cleaning to remove any type of sticky dust with cleaning material as required and re-fixing in its original / desired location with necessary connection incl provision of cable from ceiling rose to connector of fan after repairing, greasing, oiling, replacement of minor items such as pins, nut bolts, flexible wire etc incl spray painting with synthetic enamel paint in white colour complete all as specified & directed

M&L for sub main wiring with 06 Sqmm nominal cross sectional area, two single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLSH copper conductor cable with and including continuous earth wire of size 6 Sqmm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLSH copper conductor cable drawing into and including rigid non-metallic PVC concealed conduit of 20 mm dia, medium grade with all conduit accessories and connected to common earth dolly with suitable copper lugs including all cutting / chases etc in walls and making good to the disturbed surfaces to match the existing complete and all as specified & directed, including taking down old / unsv sub main wiring complete

All as as above but for 02 x 4 Sqmm for phase & neutral and 01 x 4 Sqmm for continuous earth wire

S&F (in replacement) industrial type SPN enclosure with a two pin and earth plug and socket complete with and including MCB SP, AC, 230 volts of 20 Amps, 'C' curve 10 KA breaking capacity and flush to wall including all cuttings & chases etc in wall and making good to the disturbed surfaces to match the existing complete

S&F (in replacement) sheet metal enclosure double door distribution board, single pole and neutral, AC, 240 volts, 8 way, with 200 Amps rated copper bus bar and metal door with IP - 43 & IK 09 protection along with cable end box for above DB and flush to wall including all cutting etc in wall and making good to the disturbed surfaces to match the existing complete

S&F (in replacement) sheet metal enclosure double door distribution board triple pole and neutral (VTPN), AC, 440 volts, 04 ways with 200 Amps rated copper bus bar and metal double door suitable for MCCB 125 amps as incomer and MCB SP as outgoing along with cable end box for above DB and flush to wall including all cutting etc in wall and making good to the disturbed surfaces to match the existing complete (Note :- MCCB & MCB SP will be measured seperately)

S&F MCCB 125 amps, 4 Pole, 415 volt, AC, fixed type, with breaking capacity 25 KA suitable for load line/ VTPN DB & connection complete

S&F MCB, SP, AC, 240 volts of 10 to 40 Amps capacity "B" curve, 10 KA breaking capacity and making connections by using suitable copper lugs complete

S&F MCB, SPN, AC, 240 volts of 63 Amps capacity "C" curve, 10 KA breaking capacity and making connections by using suitable copper lugs complete

Supply, laying & testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) with stranded aluminium conductor, 1100 volts grade, of the size 35 sqmm x 3.5 core

Excavation in trenches not exc 1.5 Mtr wide and n.exc 1.5 mtr in depth, getting out for electric cable/pole complete in any type of soil complete

Removing surplus excavated soil to a distance n.exc 50 mtr and depositing where directed at a level n. exc 1.5 mtr above starting point

Returning, filling in, soil obtained from excavation including spreading, levelling, watering and well ramming in layers n.exc 25cm thick complete

Supply and laying sub class 'B' bricks laid dry and flat across the length of cable for protection of cable complete

M & L for sand cushioning for protection of cable with screen wash river sand complete

M&L for earthing complete with galvanised mild steel earth plate electrode 60cmx60cmx6mm thick buried vertically in ground (earth pit not less than 2.25meter deep below ground level) with top edge of the plate not less than 1.5meter below normal ground level steel earth plate connected with GI wire 04mm dia by means of lug, bolts, nuts, check nuts, washers of galvanised iron or steel GI protection pipe 15mm bore light grade all as shown in elect plate No 3 on serial page No 497 of SSR part I - 2009 and connecting to main switch board / Main DB’s including excavation, earth work, salt and charcoal dust mixed and packed 150mm thick around GI earth plate, GI pipe medium grade 20mm nominal bore watering pipe GI sheet funnel wire mesh, concrete pit, RCC cover 40mm thick in PCC 1:2:4 type B1 duly reinforced with MS Bars 6mm dia at the rate of 75mm center to center both way with 12mm dia lifting handle and pit / chamber in PCC 1:3:6 type C1, Angle iron 40mmx40mmx3mm frame for pit cover including testing on completion complete Note:-testing of earthing after completion is in permissible limit obtained with out making extra cost.

Taking down unserviceable main switches, DBs including MCBs, bus bars chambers etc from wall / existing main boards and removing from site complete

Shri Balaji Construction

M/S ANIL KUMAR

Keshav Brothers

BEHAL TRADERS

imran construction company

Mohit Infratech

POONAM ENTERPRISES