Repairs to flooring roofs sunken floor internal water supply and misc works at MH MDC in the area of AGE B/R I under GE (N) Ahmednagar

Amount

Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15cm in thickness (below or above ground level) etc complete all as specified and directed by Engineer-in-Charge

Demolition of precast concrete block walling built in cement mortar etc complete all as specified and directed by Engineer-in-Charge

M&L for PCC 1:4:8 type D2 using 40mm graded stone aggregate in foundation, filling & mass concrete etc complete all as specified and directed by Engineer-in-Charge

M&L for brick work with fly ash bricks, old size bricks, straight or curved on plan exc 6m mean radius, built in cement and sand mortar (1:6) etc complete all as specified and directed by Engineer-in-Charge

M&L for cement concrete 1:2:4 type B1 using 20mm graded stone aggregate in lintel upto 1.50m clear span, cills, steps, seismic and other similar bands, copings and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork etc complete all as specified and directed by Engineer-in-Charge

Dismantling structural steel work including doors, gates etc complete all as specified and directed by Engineer-in-Charge

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings etc complete all as specified and directed by Engineer-in-Charge

Supply and fix pressed steel frames of size 105mmX60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed by Engineer-in-Charge

S&F Steel work in tubular / hollow section in trusses, rafter, purline, post etc. including special shaped washer, plate, cleat, etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 etc complete all as specified and directed by Engineer-in-Charge

S&F Pre - painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws etc complete all as specified and directed by Engineer-in-Charge

S&F Pre - painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc,) or any type ceiling board any thickness including cover fittets all as directed,

Material and labour for false ceiling with 10 mm thick plain non asbestos building 'E' board with decorative finish water proofed on one side fixed on and including powder coated GI fabricated grid of 60 cm X 60 cm made out of main runner of 'T' section of size 32 mm X 24 mm X 0.30 mm, cross runner made out of 'T' of section of size 24 mm X 24 mm X 0.30 mm and alround angular section of size 22 mm X 22 mm X 0.70 mm with GI clip and level adjuster duly suspended by 2 mm dia GI wire fixed to roof at 600 mm centre to centre as per manufacturere's instructions and etc complete all as specified and directed by Engineer-in-Charge

Dismantling of single layer Mangalore pattern or similar tiles in roofing etc complete all as specified and directed by Engineer-in-Charge

M&L for roof tiles, Mangalore pattern, interlocking at side joints, laid dry etc complete all as specified and directed by Engineer-in-Charge

All as per item No 15 (here-in-before) but except tiles

M&L ridges and hip tiles to joint mangalore patern tiles or roofing bedded/ jointed in cement and sand mortar (1:6) etc complete all as specified and directed by Engineer-in-Charge

Dismantling Asbestos cement (corrugated, semi-corrugated, etc.) sheets in roof coverings etc complete all as specified and directed by Engineer-in-Charge

M&L for 6mm thick asbestos cement, corrugated or semi-corrugated sheets in roofs, walls etc. fixed with L-type or J-type or cranked hook bolts etc complete all as specified and directed by Engineer-in-Charge

M&L for asbestos cement two piece adjustable serrated ridge 6mm thick for corrugated or semi-corrugated sheets fixed with L-type or J-type or cranked hook bolts etc complete all as specified and directed by Engineer-in-Charge

Dismantling of stone slabs and tiles of any description or thickness in floors, approns etc laid and bedded in any mortor etc complete all as specified and directed by Engineer-in-Charge

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises etc complete all as specified and directed by Engineer-in-Charge

M&L for joint free non skid ceramic coloured tiles 7 to 8 mm thick, area of tile exc 0.18 Sqm but not exc 0.38 Sqm as floor over and including 15 mm thick screed beeding in cement and sand mortar (1:6) set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles etc complete all as specified and directed by Engineer-in-Charge

All as per above Item No 23 (here-in-before) but as in skirting over and including, cement and sand screed in cement and sand mortar (1:4).

M&L for Virified Ceramic tiles 10 mm thick light shade (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including 15 mm thick screed bedding in cement and sand mortar (1:6), etc complete all as specified and directed by Engineer-in-Charge

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (square/ rectengular) area of each tile exc 0.06 Sqm but not exc 0.11 Sqm as in floor over and including 15 mm thick screed bedding in cement and sand mortar (1:6), set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles etc complete all as specified and directed by Engineer-in-Charge

M&L for glazed ceramic coloured tiles of size 350 X 250 X 7 mm thick on vertical surfaces such as in skirting / dados over and including 10 mm thick backing coat in cement and sand mortar (1:4) set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles etc complete all as specified and directed by Engineer-in-Charge

Taking down cement plaster on brick / stone walls including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge

M&L for rendering, 10 mm thick on stone masonry surfaces in cement and sand mortar (1:4) on wall finished surface even and smooth without using extra cement etc complete all as specified and directed by Engineer-in-Charge

M&L for rendering, 15 mm thick on stone masonry surfaces in cement and sand mortar (1:6) on wall finished even and smooth without using extra cement surface with sagol finish etc complete all as specified and directed by Engineer-in-Charge

M&L for rendering, 5 mm thick on concrete surfaces in cement and sand mortar (1:4) on ceiling finished even and smooth without using extra cement surface with sagol finish etc complete all as specified and directed by Engineer-in-Charge

M&L for two coats of cement base paint on newly plastered surfaces incl preparation etc. complete on wall including preparation of surfaces etc complete all as specified and directed by Engineer-in-Charge

M&L for two coats of oil bound distemper on newly plastered surfaces of walls including preparation of surfaces etc complete all as specified and directed by Engineer-in-Charge

M&L for one coats of OBD on Old plastered surfaces of walls including preparation of surfaces etc complete all as specified and directed by Engineer-in-Charge

M&L for complete removal of existing treatment on plastered surfaces and applying two coats of OBD over on old plastered surfaces of walls including preparation of surfaces etc complete all as specified and directed by Engineer-in-Charge

M&L for 3 coats of white wash on newly plastered surfaces incl preparation of surfaces of ceiling etc complete all as specified and directed by Engineer-in-Charge

M&L for preparation of old wall surfaces of any description & applying one coat of acrylic (antifungal) exterior grade paint on wall/roof complete all as specified.

M&L for 75mm thick PCC (1:3:6) type C-2 using 40mm graded stone aggregate as in sub base for plinth protection and path etc complete all as specified and directed by Engineer-in-Charge

M&L for 25 mm thick Granite (of any type) (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement and sand mortar (1:4) including pointing in white or coloured cement (1:2) using marble dust with admixture of pigment to match with shade of granite etc complete all as specified and directed by Engineer-in-Charge

M&L machine cut cudappah stone slab 20-25 mm thick over cement screed base, laid over and including 15 mm thick screed bed in cement and sand mortar (1:6), set and jointed with grey cement slurry mixed with pigment to match the shade of the slab of stone including rubbing and polishing etc complete all as specified and directed by Engineer-in-Charge

M&L Machined pressed precast concrete interlocking paver block glossy with grey cement and pigment , any shape and size confirming to IS 15658-2006 of 60mm thickness M-35 grade over a stone dust cushion of 30mm thick etc complete all as specified and directed by Engineer-in-Charge

M&L for Shahabad stone 25mm to 40mm thick flooring over and including screed bed or bedding layer of cement and sand mortar (1:6) 15 mm thick etc complete all as specified and directed by Engineer-in-Charge

M&L for chequered cement concrete tiles 20cm x 20cm x 25mm thick, laid over and including 15mm thick screed bed in cement and sand mortar (1:6) set, jointed and pointed in neat cement slurry with grey cement and no pigment as in etc complete all as specified and directed by Engineer-in-Charge

M&L for machine cut kota stone slab florring 18-20 mm thick over cemet screed base laid over and including 15 mm thick screed bed in cement and sand mortar (1:6), set and jointed with grey cement slurry mixed with pigment to match shade of the slab including rubbing and plishing etc complete all as specified and directed by Engineer-in-Charge

Taking down chowkhats or frames n.exc 1.5 sq. m each with shutters (without taking off shutters from the frame) etc complete all as specified and directed by Engineer-in-Charge

Taking down chowkhats or frames exc 1.5 sq. m but n.exc 4.0 sq. m each with shutters (without taking off shutters from the frame) etc complete all as specified and directed by Engineer-in-Charge

Supply and fix 35mm thick factory made plain framed pannelled shutter (two panel) with lock rail and panel of 9mm B.W.P commercial plywood. The size of rail and stile as per IS : 1003(Part I), kiln seasoned and chemically pressure treated etc complete all as specified and directed by Engineer-in-Charge

Supply and fix 35mm thick factory made glazed and skeleton shutters, open rebated and to receive glass, gauze, etc(without sash bars), edges of framing plain, chamfered or rounded. Fitted with cut and mitered beads for securing glass, etc; sizes of me-mbers of shutters as specified in SSR Part-I, section 8, clause 8.24(a) etc complete all as specified and directed by Engineer-in-Charge

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing etc complete all as specified and directed by Engineer-in-Charge

S&F factory made solid PVC door shutter 30 mm thick (style) consisting of frame made out of mild steel tubes for top and bottom rails frame shall be covered with heat moulded plain coloured PVC `C' channel having a PVC sheet strip of 20 mm width stuck and plain colour PVC sheets for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the mild steel frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement, supplying and fixing in the frame etc complete all as specified and directed by Engineer-in-Charge

Taking down aluminium doors/windows shutters only and dismantling all members and reassembling the same with and including new screws, new rubber gasket new alumunium cleats of exesting make and also refixing the locks & roller in existing position with and including new screws refixing the window shutter in same opening etc complete all as specified and directed by Engineer-in-Charge

S&F 100 mm long butt hinge, medium weight, cold rolled mild steel etc complete all as specified and directed by Engineer-in-Charge

S&F 200 mm long aluminium anodised barrel tower bolt, of extruded sections etc complete all as specified and directed by Engineer-in-Charge

S&F 150 mm long aluminium anodised handle, cast type etc complete all as specified and directed by Engineer-in-Charge

S&F aluminium extruded section door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed etc complete all as specified and directed by Engineer-in-Charge

S&F powder coated anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete etc complete all as specified and directed by Engineer-in-Charge. Make :Jindal/Hindalco.

S&F powder coated anodised aluminium fully glazed door shutters side hung type, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc complete all as specified and directed by Engineer-in-Charge (Note : Glass will measured and paid separately under relevant item of this BOQ)

S&F powder coated anodised aluminium glazed window shutter side hung / aluminium sections weighing 0.55 kg/m aluminium open track section having reqd size of style and top rails, bottom rails including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) etc complete all as specified and directed by Engineer-in-Charge (Note : Glass will measured and paid separately under relevant item of this BOQ)

M&L Block board, 12 mm thick, grade 1 quality, exterior grade, decorative type with decorative face veneer on one face, fixed with screws to timber frame work etc complete all as specified and directed by Engineer-in-Charge

M&L for second class hard wood beads, straight (any size) for glazed or gauzed joinery, renewed, including mitres etc and removing old beds etc complete all as specified and directed by Engineer-in-Charge

S&F stainless steel wire cloth 0.36 nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples etc complete all as specified and directed by Engineer-in-Charge

All as per item No 61 (here-in-before) but fixed in repairs.

M&L for 5.5mm thick sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 Sq. m in each pane with solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers etc complete all as specified and directed by Engineer-in-Charge

S&F 150 mm long floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring etc complete all as specified and directed by Engineer-in-Charge

S&F in repair mortice lock, vertical type, size 100mm brass 4 levers etc complete all as specified and directed by Engineer-in-Charge

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones etc complete all as specified and directed by Engineer-in-Charge

M&L for glazing with 3 mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.50 sqm in each pane etc complete all as specified and directed by Engineer-in-Charge

M&L for glazing with 3 mm thick figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane etc complete all as specified and directed by Engineer-in-Charge

S&F continous (piano) hinges, mild steel, bright finish or electro galvanised (width of flaps 30mm ) etc complete all as specified and directed by Engineer-in-Charge

S&F 125mm hasp and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws etc complete all as specified and directed by Engineer-in-Charge

S&F 125 mm long aluminium anodised handle, cast type etc complete all as specified and directed by Engineer-in-Charge

M&L for preparation of new or previously untreated steel surface of any description not otherwise described over 10 cm width or girth and apply two coats of synthetic enamel paint over one coat of pink primer etc complete all as specified and directed by Engineer-in-Charge

M&L for preparation of new or previously untreated wooden surface of any description not otherwise described over 10 cm width or girth and apply two coats of synthetic enamel paint over one coat of red oxide primer etc complete all as specified and directed by Engineer-in-Charge

S&F in repair Mild Steel decorative powder coated curtain rods with fixing brackets,knobs, rings etc. etc complete all as specified and directed by Engineer-in-Charge

S&F in repair 10 mm thick semi circular glass for shelves in corner with chamferred edges incl connectedbrackets etc complete all as specified and directed by Engineer-in-Charge

S&F in repair health faucet with all connected accessories etc complete all as specified and directed by Engineer-in-Charge. Cat no 563 make Jaquar or equivalent parryware / Cera / Hindware / Plumber

S&F in repair wall mixture, 3-in-1 with provn for both & over head shower with 115 mm long bend type & wall flange complete etc complete all as specified and directed by Engineer-in-Charge. Cat no 5273 - UPR make Jaquar or equivalent parryware / Cera / Hindware

S&F in repair Brass Chromium Plated toilet paper holder fixed with (CP) brass screws of approved quality etc complete all as specified and directed by Engineer-in-Charge

S&F in repairs decorative towel ring chromium plated 150 mm dia fixed with (CP) brass screws of approved quality etc complete all as specified and directed by Engineer-in-Charge

S&F in repairs 32 mm dia PVC waste pipe (outlet pipe) plain fixed to waste coupling of WHB or sink etc of approved quality etc complete all as specified and directed by Engineer-in-Charge

S&F in repair, brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges etc complete all as specified and directed by Engineer-in-Charge

Supply and fix in repairs pillar taps, fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed in 15mm dia bore pipe etc complete all as specified and directed by Engineer-in-Charge

S&F in repair Self-closing flush taps for urinal, cast copper alloy, chromium plated, screwed for iron pipe and fixed 15mm bore pipe etc complete all as specified and directed by Engineer-in-Charge

Supply and fix in repair bib tap, 15 mm dia, CP cast copper alloy screwed down for iron pipe or for brass ferrule etc complete all as specified and directed by Engineer-in-Charge.Make:- Cat part No MMO 1020 (Quarter Turn) of Movements series of MARC or equivalent in Plumber / Jaquar.

Supply and fixing in repairs stop valve cast copper alloy, fancy type screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union and fix of size 15 mm bore Make:- Cat part No MMO 1040 concealed stop cock (Quarter Turn) of Movements series of MARC or equivalent in Plumber / Jaquar / ESS-ESS

Supply and fix in repairs, shower rose with shower arm from Make:- Cat part No MARC MSR1050 (Shower) and MOR 1260(Shower arm) from MARC or equivalent in Make Plumbe/,ESS-ESS/ Jaquare

S&F PVC connections 15 mm size with PTMT nuts of length 450 mm etc complete all as specified and directed by Engineer-in-Charge

Supply and fix in repairs looking mirror of size 600 mm X450 mm etc complete all as specified and directed by Engineer-in-Charge. Make:- Cat part No C 8606 Of Parryware or equivalent in Jaquar / Cera

Dismentling of water tanks of capacity exc 250 and n.exc 500 ltrs and removing from site etc complete all as specified and directed by Engineer-in-Charge

Dismentling of water tanks of capacity exc 500 and n.exc 1000 ltrs and removing from site etc complete all as specified and directed by Engineer-in-Charge

Supply and fix rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of 500 litres capacity, double layered, hoisted and fixed in position including 20 mm dia ball valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed to iron pipe and connecting etc complete all as specified and directed by Engineer-in-Charge

All as per item No. 91 (here-in-before) but 1000 ltr capacity

S&F in repair gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed of 20mm bore fixed in repair etc complete all as specified and directed by Engineer-in-Charge

S&F in repair ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed in 20mm dia bore pipe etc complete all as specified and directed by Engineer-in-Charge

Taking down 15 mm dia steel GI tubing including all connected fittings of any dia and in any position including cleaning for re fixing the serviceable pipe etc complete all as specified and directed by Engineer-in-Charge

All as per item No 95 (here-in-before) but 20mm dia pipe.

S&F 15 mm dia galvanised steel tubing medium grade including necessary fittings like sockets, tees, elbows, reducers, unions etc fixed to walls / ceiling etc complete all as specified and directed by Engineer-in-Charge

All as per item No 97 (here-in-beofre) but fixing only.

All as per item No 97 (here-in-before) but 20mm dia pipe.

Taking down eaves gutters and rain water pipes (any size or pattern) including all fittings, heads, shoes, bends, swan-necks etc., including cleaning or refixing or removal to Store (measured overalll as fixed along the cente line over fittings and accessories) etc complete all as specified and directed by Engineer-in-Charge

S&F 110 mm dia PVC SWR pipe, single socketed in any length with rubber ring joints fixed with clamps to walls etc complete all as specified and directed by Engineer-in-Charge

S&F 75 mm dia PVC SWR pipe, single socketed in any length with rubber ring joints fixed with clamps to walls etc complete all as specified and directed by Engineer-in-Charge

S&F 110 mm bore PVC (SWR) branch piece double (single Y) equal or unequal etc complete all as specified and directed by Engineer-in-Charge

S&F 110 mm dia PVC (SWR) bend any radius etc complete all as specified and directed by Engineer-in-Charge

S&F 75 mm dia PVC (SWR) bend with access door any radius etc complete all as specified and directed by Engineer-in-Charge

S&F PVC (SWR) floor trap, 75 mm dia with grating including jointing with solvent cement etc etc complete all as specified and directed by Engineer-in-Charge

S&F in repairs 32 mm dia low density polyethylene pipes (LDPE) of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors etc complete all as specified and directed by Engineer-in-Charge

Supply and fix PVC valveless, syphonic action type, flushing cistern,low level, all accesories all as directed. Make :- Sleek essence series Of Hindware or Cat part No E8303 Of Parryware or equivalent in Cera

Supply and fix in repairs vitreous China white squatting pan, Orissa pattern of size 580 X 440 mm width with integral foot rest set in cement concrete including flush pipe and connecting to trap / flushing cistren complete all as specified and directed.Make :- Cat Part No C0117 Of Parryware or Cat Part No 20042 of Hindware or equivalent in Cera

Supply and fixing in repairs vitreous china wash down water closet (Pedestal pattern) white including fixing bolts with and including plastic water closet seat cover closed pattern with flat bottom and cover and MSCP almn hinges device complete connecting to 'P' or 'S' trap all as directed. Make:-Petite series Cat part No C0287(S)/88(P) Incl seat cover Cat part No E8309 of Parryware or equivalent in Hindware / Cera

Supply and fixing in repair plastic water closet seat, white ,closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device , seat and cover for water closet (European type) complete all as specified and as directed. Make:-Anti microbial of Cera or equivalent in Parry ware , Hindware

Supply and fix in repairs wash hand basin vitreous China coloured , flat back pedastal pattern of size 630 X 510 mm, (for hospital use) waste chain and plug and porcelain stopper, waste pipe, incl cutting for and pinning in ends of brackets in cm 1:3 etc complete all as .Make :- Cat Part No S2040111 & S2090107 Of Cera or equivalent in Parryware Hindware

Supply and fix

Supply and fix in repairs stainless steel kitchen sink matt finish with draining over all size 950 X 510 mm and bowl size 410 X 410 X 230 mm, made out of 1.00 mm thick SS sheet of high quality including a pait of brackets, waste coupling, plug and chain, 32 mm dia PVC flexible waste pipe and nahani trap complete all as specified and directed. Make : (i) Model Olympia Satin Finish silent square range of Nirali or equivalent in Dimond / Blue Star (ii) Waste Coupling of make : Plumber / Marc / ESS-ESS

Supply and fixe in repairs stainless steel kitchen sink matt finish without draining bowl size 410 X 410 X 230 mm, made out of 1.00 mm thick SS sheet of high quality including a pait of brackets, waste coupling, plug and chain, 32 mm dia PVC flexible waste pipe and nahani trap complete all as specified and directed. Make : (i) Model Omni mini Satin Finish of Nirali or equivalent in Dimond / Blue Star.

M&L 3 mm thick wall care putty on wall (One layer) etc complete all as specified and directed by Engineer-in-Charge.

An amount of Rs 55,196.00 shall be deducted from BOQ on account of schedule of credit

M/S-B.R.SONAWANE

Ms. M.D. Auty

M/s. N D Karande

G.M. Construction

Priyadeep Construction

OM SAI ASSOCIATES