GE 861 EWS-46(T)/2025-26

Taking down cement plaster on brick or concrete surfaces including raking out joints, hacking for key scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) n.exe 1.50 Sqm each complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete in ground floor and paving n.exe 15 cm thick below or above GL complete all as specified and directed by Engineer-in-Charge.

M&L for 4mm thick sheet glass ordinary quality and glazing with oil putty or fixed with bead/glazing pins in squares n exc 0.5 Sqm in each pane complete all as specified and directed by Engineer-in-Charge.

S&F aluminium handle extruded fabricate type anodised of size 150 mm complete all as specified and directed by Engineer-in-Charge.

S&F factory made solid panelled PVC door shutter 30mm thick (stile) consisting of frame made out of MS tube for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail lock rail and bottom rail on either side and gap insert for top rail and bottom rail panelling of plain colour PVC to sheet to be fitted in the MS frame welded / sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified and directed by Engineer-in-Charge.

S&F butt hinges 75 mm medium weight cold rolled mild steel complete all as specified and directed by Engineer-in-Charge.

All as per Ser item No-89 here in above but for one 3 pin 5A socket outlet independent controlled by one switch complete all as specified and directed by Engineer-in-Charge.

Description all as per item No-89 above but for 3 pin socket outlet 15 Amps independent board with 2.5 Sqmm complete all as specified and directed by Engineer-in-Charge.

S&F 20 mm bore GI tubing medium grade galvanised with all fittings and fixed complete to walls & floors etc complete all as specified and directed by Engineer-in-Charge.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm fixed with tinned tacks, or stainless steel wire staples complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 10 mm thick in cement mortar 1:6 finishing on brick or concrete surfaces finished even & smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for two coats of synthetic enamel paint on new wooden surfaces over coat of pink to new surfaces including preparation of surfaces, over 10cm width or girth complete all as specified and directed by Engineer-in-Charge.

M&L for 75 mm thick PCC (1:3:6) type C-2 using 40mm grade crushed stone aggregate as in plinth protection etc finished even & smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for two coats of synthetic enamel paint on old wooden surfaces including preparation of surfaces over 10cm width or girth complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of plastered or unplastered old surface of walls and applying two coats of cement base paint on walls (externally) including removal of existing treatment complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 15mm thick on fair face of brick work or concrete surface in cement mortar 1:4 finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for applying 3 mm thick wall care putty on old surfaces of wall and applying two coats of oil bound distemper on wall including complete removal of existing treatment complete all as specified and directed by Engineer-in-Charge.

Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering complete all as specified and directed by Engineer-in-Charge.

S&F Factory made solid PVC door frame of size 50mm x 47mm made out of 5 mm single side prelaminated PVC sheet reinforced with MS square tube manufactured as per SSR Part-I specifications and drawings complete all as specified and directed by Engineer-in-Charge.

M&L for two coats of synthetic enamel paint on new steel surfaces over coat of red-oxide zinc chrome primer including preparation of surfaces, over 10cm width or girth complete all as specified and directed by Engineer-in-Charge.

S&F for 10 mm thick PVC insulation panels with EPS stuck to 1 mm plain PVC sheet suitably placed in false celling grid made of aluminium & GI/MS as per specification and drawing complete all as specified and directed by Engineer-in-Charge.

Dismantling of timber scantling 40sqcm and over in section in any position in unframed work complete all as specified and directed by Engineer-in-Charge.

M&L for applying two coats of Fire Retardant Water Based Wall Paint protective coating to reduce flame spread and enhance fire resistance for wa

M&L PCC (1:4:8) type D-2 using 40mm graded stone aggregate as in foundation, filling and mass concrete complete all as specified and directed by Engineer-in-Charge.

S&F in repairs timber frame work in clean sawn second class hard wood as in scantling etc com

Supply and fixing for Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 MPA as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer-in-Charge.

Taking down carefully aluminium point wiring (light, fan, socket or power, bell complete fitting such as sockets, ceiling roses, pendants, batten holders, regulators and making good the disturbed surfaces of wall, floors, ceiling in CM (1:3) etc complete all as specified and directed by Engineer-in-Charge.

M&L for Point wiring for one light point/fan point controlled by one switch with 1.5 Sqmm PVC FRLS insulated unsheathed copper conductor single core multi strand flexible cable and 1.5 Sqmm PVC insulated unsheathed copper conductor single core cable (green colour) as earth lead in and including PVC casing and capping/Conduit medium grade of suitable size run on wall/surface with all fittings (ISI Marked) controlled by one switch including CI/MS sunken box of required size or PVC Gang Box all as directed by Engr-in-Charge & 3mm thick plastic laminated sheet, including cutting chases to wall making good the disturbed surfaces to match with the existing specification complete all as specified and directed by Engineer-in-Charge.

S&F switch piano flush type 5/6 Amps single pole one way complete all as specified and directed by Engineer-in-Charge. (Make - Anchor/Cona/Kinjal)

S&F LED lights fitting 1x10W, bulkhead luminaries including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete as of suitable size from ceiling rose complete all as specified and directed by Engineer-in-Charge.

S&F mild steel work in Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embedding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed by Engineer-in-Charge.

S&F laying in trenches, pole, and along wall etc complete, XLPE insulated, armoured heavy duty electric cable with stranded aluminium conductor, 1100 volt grade, cross sectional area 16 Sqmm 2 core complete all as specified and directed by Engineer-in-Charge.

Excavation in trenches in not exceeding 1.5 mtr vide and 1.5 mtr in depth and getting out in any type of soil for laying of under ground cable complete all as specified and directed by Engineer-in-Charge.

Removing of surplus excavated material to a distance n. exc 50 mtr and deposing where directed at a level not exceeding 1.5 mtr from the starting point complete all as specified and directed by Engineer-in-Charge.

M&L for sand cushioning in trenches for cable protection complete all as specified and directed by Engineer-in-Charge.

M&L for Roof Treatment of roof of Bldg/Stair Case/Tank Portion including the fwg:- (i) Roughening surface of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. (ii) M&L for 25mm thick Cement Concrete padding, type B-0,1:2:4 (12.5mm graded crushed stone aggregate) as in top of roof. (iii) Rendering or bedding layer of mortar 15mm thick in cement mortar 1:4 (rendering is to be finished even and smooth in without using extra cement) for applying water proofing treatment (v) Applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 Kg /Sqm over bituminous primer @ 0.30ltr per Sqm including cleaning and preparing surfaces. (vi) APP based polymeric membrane minimum weight 3Kg/Sqm and minimum 3mm thick reinforced with polyester non woven fabric laid on primed surface by torched application method.

M&L for 100 mm thick PCC (1:4:8), type D-2 in sub base using 40 mm graded crushed stone aggregate complete all as specified and directed by Engineer-in-Charge.

Supply and fix MCB Distribution board, 240 volts single pole and neutral, double door, sheet steel, enclosure powder coated with 100 Amps rated bush bar with neutral link, 12 ways, fixed on wall duly grouted in solid block wall or on wooden board with electrical connection complete all as specified and directed by Engineer-in-Charge. Make: Indoasian Cat part Nol:KSLT0008 or equivalent in Legrand/ Havells/ ABB

Supply and fix MCB Distribution board, 240 volts single pole and neutral, double door, sheet steel, enclosure powder coated with 100 Amps rated bush bar with neutral link, 8 ways, fixed on wall duly grouted in solid block wall or on wooden board with electrical connection complete all as specified and directed by Engineer-in-Charge. Make: Indoasian Cat part Nol:KSLT0008 or equivalent in Legrand/ Havells/ ABB.

Supply and fixing 240V, 10KA 'C' curve miniature circuit breaker (MCB) of current carrying SPN 40-63 Amps capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 6 to 32 Amps in the MCB DB Complete with connection testing and commissioning complete all as specified and directed by Engineer-in-Charge.

Supply and fix Bus Bar Chamber of size 60 x 60 x 45 cm suitable of 3 phase 433 Volts outdoor type made out of 3.15 mm thick M S Sheet with 400 Amps rated aluminium bush bar (4 Nos ) PVC sleeves and coloured (Red, Yellow, Blue and Black) with locking arrangements and angle iron stand of size 40 x 40 x 6mm frame grouted in ground with PCC foundation (1:2:4) type C1 with 20mm graded stone aggregate alongwith all necessary cable connections, lugs and cable gland including 2 coat of paint over a coat of red oxide primer complete all as specified and directed by Engineer-in-Charge.

M&L for cement concrete type C2 (1:3:6) (using 40mm graded crushed stone aggregate) for fixing of post in post holes complete all as specified and directed by Engineer-in-Charge.

ll and Ceiling complete all as specified and directed by Engineer-in-Charge.

Taking down copper/aluminium sub main wiring of any size complete without conduit complete all as specified and directed by Engineer-in-Charge.

Taking down main switches/DBs/Change over switches etc complete all as specified and directed by Engineer-in-Charge.

S&F fan regulator Electronic type complete all as specified and directed by Engineer-in-Charge (Make-Anchor/Cona/Kinjal).

S&F Lamp holder insulated body with back plate for batten fittings complete all as specified and directed by Engineer-in-Charge.

Supply only LED lamp 9 Watt, 230 Volts complete all as specified and directed by Engineer-in-Charge.

S&F Flame proof light fitting 1x45W (BIFPWG) LED light driver connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engineer-in-Charge. Make: Bajaj Cat part No 45W LED (BIFPWG) or equivalent in Havells, Crompton, Sudhir

M&L for sub main wiring with two single core PVC insulated unsheathed, FRLS flexible copper conductor cable of size 6 Sqmm and one single core PVC insulated unsheathed FR flexible copper conductor cable of size 4 Sqmm as earth lead in & including PVC casing/non Metallic rigid PVC conduit medium grade and making good the disturbed at site or complete all as specified and directed by Engineer-in-Charge.

Supply and fixing electronic water heater, storage type steel body with copper inner tank and heating element up to 2 KW capacity 25 Ltrs, BEE 5 star rated complete with all accessories such as safety valves, thermostat, NRV, connections piece etc complete all as specified and directed by Engineer-in-Charge (old unserviceable geyser will be deposited at MES Store yard).

S&F energy exhaust fan 300 mm sweep sturdy engineering plastic complete with lovers shutters, voltage 230V, 50Hz, RPM 1200, copper winding making hole in wall as it where required and , connecting electrically to ceiling rose or connector block using PVC insulated and overall sheathed 3 core cable of size 0.75 Sqmm with flexible copper conductor all as required at site and old UNSV Exhaust fan from building depositing to MES store yard complete all as specified and directed by Engineer-in-Charge.

S&F LED light fitting mirror type with high out put diffuser 1x5Watt, 220V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engineer-in-Charge.

Supply and fixing LED luminaire 600 mm x 600 mm, 36 watt (White/ Warm White), 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed by Engineer-in-Charge.

Taking down ceiling fan of any size after disconnecting the wire from existing ceiling rose and deposited to MES Store yard and Supply & fix ceiling fan complete with blades, down rods, electronic regulator and accessories, 230V, 1200mm sweep Min air delivery 210 CFM with service valve 6.00 BEE. Five star rated brushless direct current motor (BLDC) complete all as specified and directed by Engineer-in-Charge.

M&L for Point wiring for one light point/fan point controlled by one switch with 1.5 Sqmm PVC FRLS insulated unsheathed copper conductor single core multi strand flexible cable and 1.5 Sqmm PVC insulated unsheathed copper conductor single core cable (green colour) as earth lead in and including stove enamelled steel conduit medium grade of suitable size run on wall/surface with all fittings (ISI Marked) controlled by one switch including CI/MS sunken box of required size or PVC Gang Box complete all as specified and directed by Engineer-in-Charge & 3mm thick plastic laminated sheet, including cutting chases to wall making good the disturbed surfaces to match with the existing specification complete all as specified and directed by Engineer-in-Charge.

S&F laying in trenches, pole, and along wall etc complete, XLPE insulated, armoured heavy duty electric cable with stranded aluminium conductor, 1100 volt grade, cross sectional area 25 Sqmm 3 core complete all as specified and directed by Engineer-in-Charge.