SPECIAL REPAIR TO AUDITORIUM IN P ONE BLDG AT AFSSR GURGAON AND PROVISION OF BASKET BALL COURT AT NTS GURGAON UNDER GE AF GURGAON

Amount

Demolition of cement concrete (un-reinforced ) of any description & in any position not specifically provided for including dismantling of floor tiles etc complete all as specified and as directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc and including removal of debris and rubbish from the site complete all as specified and as directed by Engr-in-Charge. Note the area includes in this up to 15 metre height of building

Dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed by Engr-in-Charge.

M&L for screed bed or bedding layer of mortar 15mm thick in CM 1:4 for laying floor finishes complete all as specified and as directed by Engr-in-Charge.

M&L Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed by Engr-in-Charge.

M&L for 75 mm thick cement concrete 1:4:8 type D2 using 40 mm graded stone aggregate in sub base complete all as specified and as directed by Engr-in-Charge.

M&L for exterior grade, coloured glossy finish rubber pressed, cement concrete designer chequered tiles of size 30cm x 30cm x 25mm thick ( as approved by GE) set, jointed and pointed in neat cement slurry with grey cement and pigment to match the shade / colour / matrix of tiles as in floor etc laid over including 15 mm thick cement screed bed in CM 1:6 . complete all as specified and as directed by Engr-in-Charge.

Dismantling of old unserviceable rolling Shutter/Steel Gate of area n exc 25 Sqm each of any description including making good surface and removing to Store complete all as specified and as directed by Engr-in-Charge.

M&L for mild steel framed work as in grills, grating, doors, etc with ends of bars shouldered and / or riveted or forged into spikes framed guard bars barred iron doors, ladders framed baluusters wals ways, railing framed wor of water tans and similar work etc complete all as specified and as directed by Engr-in-Charge.

S&F Mild steel, plain black sheet 1.6mm thick in door shutters,, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and as directed by Engr-in-Charge.

Taking down shutter of any description area exc 1.00 Sqm and not exc 2 Sqm each and removing from site complete etc complete all as specified and as directed by Engr-in-Charge.

Taking down shutter of any description area exc 2 Sqm each and removing from site complete etc complete all as specified and as directed by Engr-in-Charge.

S&F 30mm flush shutter solid core construction with block board core and ply wood face panels, commercial type on both sides complete all as specified and as directed by Engr-in-Charge.

S&F Anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and as directed by Engr-in-Charge.

S&F Aluminium anodised tower bolt 200 mm long of extruded section etc complete all as specified and as directed by Engr-in-Charge.

S&F aluminium alloy, anodised sliding door bolt 300 mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy etc complete all as specified and as directed by Engr-in-Charge.

S&F 100 mm thick butt hinges, heavy weight, cold rolled mild steel and fixed etc complete all as specified and as directed by Engr-in-Charge.

S&F 125 mm long aluminium handle, cast type, anodised etc complete all as specified and as directed by Engr-in-Charge.

S&F Double legged Floor door stopper of aluminium alloy body and tongue anodised with hard drawn steel spring fixed to door shutter of size 140mm complete all as specified and as directed by Engr-in-Charge.

M & L for Solid PVC Wall Lining consisting of 5mm thick prelaminated PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as specified and as directed by Engr-in-Charge.

M & L for 5mm thick PVC sheet fillet of width 35mm for wall panelling inclusive of fixing on to wall with rawl plug to make PVC Frame as per specification and drawing complete all as specified and as directed by Engr-in-Charge.

S&F Aluminium extruded standard clips, anodised (15 micron) fixed to existing panels of framed doors, partiions etc as in repairs incl taking down existing aluminium clips complete all as specified and as directed by Engr-in-Charge. Note : The clips shall be of section No : 19370 of JINDAL aluminum extrusions or equivalent section in makes as specified and directed.

S&F neoprene beading suitable for fixing glass panes to aluminum door shutters complete all as specified and as directed by Engr-in-Charge.

S&F pivot hinges 100mm suitable for aluminium door shutters complete all as specified and as directed by Engr-in-Charge.

S&F aluminium beading 0.7mm thick for aluminium door and partitions complete all as specified and as directed by Engr-in-Charge.

M&L in repairs 12mm Prelaminated particle board, interior grade,prelaminated on both sides with decorative choice lamination fixed with screws to timber frame work complete all as specified and as directed by Engr-in-Charge.

S&F in repairs aluminium grills standard design, fixed in position including taking down existing unserviceable grills of any description and making good the disturbed surfaces complete all as specified and as directed by Engr-in-Charge. Note: The weight of the grill shall not be less than 2.2 Kg/SqM

M&L for brick work with sub class 'B' brick, straight or curved on plan exc 6.0 mtr mean radius built in CM 1:6 etc complete all as specified and as directed by Engr-in-Charge.

M&L for rendering 15 mm thick in CM (1:6) on fair faces of brick work or concrete surface finished even and smooth (without using extra cement) etc complete all as specified and as directed by Engr-in-Charge. Note the area includs in this up to 10 metre height of building

M&L for PCC 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in coping, benching, bed block, window cills etc complete all as specified and as directed by Engr-in-charge.

M&L for preparation of newly plastered surface and applying 1-2mm thick birla putty on wall surfaces complete all as specified and as directed by Engr-in-Charge.

M&L for applying two coat of oil bound distemper white or any tint over a coat of primer on newly plastered wall with roller complete all as specified and as directed by Engr-in-Charge.

Complete Removal of existing treatment on wall complete all as specified and as directed by Engr-in-Charge.

M&L for applying 1-2mm birla putty on wall surfaces and applying two coat of oil bound distemper white or any tint over a coat of primer on old plastered wall with roller complete all as specified and as directed by Engr-in-Charge.

M&L for preparing of old painted surfaces of wood & wood based surface of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed by Engr-in-Charge.

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and as directed by Engr-in-Charge. Note : This is to be done at a height of 15-20 mtr above ground level.

M&L for preparation of new or untreated surfaces of steel surface of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide and zinc chrome primer 'complete all as specified and as directed by Engr-in-Charge.

M&L for preparation of old painted surfaces of steel surface of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed by Engr-in-Charge.

M&L for preparation of old painted surfaces of steel surfaces of any description, n.exc 10cm in width or girth and applying two coats of Aluminium paint complete all as specified and as directed by Engr-in-Charge. Note : This is to be done at a height of 15-20 mtr above ground level.

S&F 8mm pre painted perforated micro tegular edge calcium silicate tiles of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600mm x 600mm grid (Frame work for ceiling shall be measured and paid separately) complete all as specified and as directed by Engr-in-Charge. Make saint Gobin/ Arm strong/Aerolite or Equivalent. Note : This is to be done at a height of 15-20 mtr above ground level.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding towall, fixed with self tapping screws complete all as specified and as directed by Engr-in-Charge. Note : This is to be done at a height of 15-20 mtr above ground level.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and as directed by Engr-in-Charge.

Rolling and consolidating formation surfaces in cutting with power roller exc 8 tonne and n.exc 12 tonne including watering as necessary and consolidating to the required level, gradient or camber, keeping roller wheels wet, if required complete all as specified and as directed by Engr-in-Charge.

M&L for 150 mm thick spread thickness of soiling (or sub base) with broken boulders or quarried stone, interstices filled surfaces formed and rolled and consolidated with 8 to 12 tonne power roller to required gradient and camber etc complete all as specified and as directed by Engr-in-Charge.

M&L for PCC (1:2:4), type B-2 (using 40 mm graded crushed stone aggregate), 100mm thick as in flooring finished even & smooth without using extra cement as all specified (add recron 3s fibre qty as per manufactures instruction when the concrete is green and fresh and rates are included in this item) complete all as specified and as directed by Engr-in-Charge.

M&L for plastic dividing strips, 1.5mm thick, 100mm wide and inserted in position, conform to design complete all as specified and as directed by Engr-in-Charge.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and as directed by Engr-in-Charge.

M&L for providing plain cement concrete 1:2:4 type B-2 (using 40mm graded stone aggregate) as in foundation and mass concrete complete all as specified and as directed by Engr-in-Charge.

Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting outin hard/dense soil complete all as specified and as directed by Engr-in-Charge.

M&L for laying synthetic layers system over cement concrete/bituminous surfaces in 8 layers acrylic system (1 layer of primer, 1 layer of Resurfacer, 3 layers of Cushion, 2 layers of colours and i court marking) etc complete all as specified and as directed by Engr-in-Charge.

S&F basketball poles with acrylic board (madeout of 150mm dia steel pipe 3.2 mtr long with 20mm thick acrylic board and dunking rings & net as approved by GE) including painting on pole with two coats of synthetic enamel paint over a coat of red oxide primer etc complete all as specified and as directed by Engr-in-Charge.

Taking down carefully copper/aluminium point wiring (light, Fan, Socket or power) fitting such as switches, ceiling roses, pendents, regulators, sockets etc complete removing material to store for keeping in safe custody and making good disturbed surfaces of walls, floors etc complete all as specified and as directed by Engr-in-Charge.

Taking unserviceable sub main wiring of any type/size including wires, conduits/battens etc complete all as specified and directed by Engr-in-Charge.

Taking down unserviceable MCB DB's/AC's box of any size/rating complete all as specified and directed by Engr-in-charge.

M&L for point wiring complete with stranded copper conductor 1.5 Sqmm size (Nominal area) PVC insulated unsheathed FRLS Grade cable 1100 volts grade confirming to IS: 694 for phase and neutral drawn in and including medium duty concealed PVC conduit confirming to ISI marked not less than 20mm dia with concealed sunk-in pressed steel terminal boxes of required size not less than 1.2 mm thick factory made and painted with stove enamelled black paint top cover 2.80 mm thick plastic laminated sheet of required colour fixed with brass screwes and cup washers including single core stranded copper conductor 1.5 Sqmm PVC insulated unsheathed cable as earth wire to common earth and connected to earth dolly drawn in same concealed conduit complete all as specified for the following :- Note: - This is maint work for routine daily complaints and keeping in view the fact contractors has to deply Elect & Helper to complete the daily works alloted and the work shall be completed within 48 hrs failing which Rs 200/- per complaint/day shall be recovered from the contractor.

One light point controlled by one switch with cables 1.5 Sqmm size complete all as specified and directed by Engr-in-Charge.

One 5 pin socket oulet 5/6 amps on same board including single core stranded copper conductor 1.5 sqmm PVC insulated and unsheathed cable drawn in same conduit as earth wire to the common earth and connecting to earth dolly complete all as specified and directed by Engr-in-Charge.

One 3 pin socket outlet, 5 Amps, independent, with cables 1.5 sqmm of size complete all as specified and directed by Engr-in-Charge.

All as per item No 56.00 hereinbefore but one 3 pin socket outlet, 15 Amps on independent boards with cables 2.5 Sqmm size complete all as specified and directed by Engr-in-Charge.

Supply and fix in repairs switch piano, flush type single pole, one way, 5 Amps, 240 volts complete all as specified and directed by Engr-in-Charge.

Supply and fixing in repairs socket outlet 2 in 1, 3 pin 5 Amps complete all as specified and directed by Engr-in-Charge.

Supply and fix switch in repairs socket combination 5 Amps/16 Amps, 5 in 1, flush type complete all as specified and directed by Engr-in-Charge.

Supply and fix in repairs ceiling roses, 3 phase, PVC/Polycarbonate, isolated body complete all as specified and directed by Engr-in-Charge.

Supply and fix in replacement of 20 watt (4ft long) decorative box type fitting with blue coloured end caps for LED tube etc complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable from ceiling rose to terminal block and testing complete all as specified and directed by Engr-in-Charge.

M&L for earthing complete with galvanized steel earth plate electrode 600 x 600 x 6mm thick burried directly in ground not less than 2.25m deep below normal ground level (with the top edge of the plate not less than 1.50 m below the normal ground level) connected to GI earth wire 4 mm by means of GI bolts, nuts, check nuts and washers of GI all as shown in electrical plate No.3 of SSR Part-I connected to earthing test point with and including necessary excavation and earth work in any strata PCC pit 1:3:6 type C-1, 20mm bore medium grade GI pipe for watering 15mm bore light grade pipe for GI wire protection and funnel including 40mm thick RCC slab cover and testing on complete all as specified and as directed by Engr-in-Charge.

S&F submain wiring with unsheathed multi-stranded FRLS Grade copper conductor cable 1100 volts grade drawn through in and including PVC rigid conduit medium grade of not less than 25mm dia with conduit accessories and concealed in wall/surface of ceiling for two runs of 6 Sqmm single core HR Grade and one run of 6 Sqmm PVC insulated copper conductor for earth continuity wire between main DB to Sub main DB complete all as specified and as directed by Engr-in-Charge. Note :- 1.Two run of single core cable with one run of earth continuity conductor and PVC conduit and accessories will be measured as one length including cutting chasing in wall complete. Note 1: Rates are deemed to be included for chases of conduit and sunking for boxes cutting and making holes in wall/floor for passing in or through conduit.

S&F submain wiring with unsheathed multi-stranded FRLS Grade copper conductor cable 1100 volts grade drawn through in and including PVC rigid conduit medium grade of not less than 25mm dia with conduit accessories and concealed in wall/surface of ceiling for two runs of 4 Sqmm single core HR Grade and one run of 1.5 Sqmm PVC insulated copper conductor for earth continuity wire between main DB to Sub main DB complete all as specified and as directed by Engr-in-Charge. Note :- Two run of single core cable with one run of earth continuity conductor and PVC conduit and accessories will be measured as one length including cutting chasing in wall complete. Note 1: Rates are deemed to be included for chases of conduit and sunking for boxes cutting and making holes in wall/floor for passing in or through conduit.

S&F vertical type load line distribution board, double door, 4 way AC, 3 phase 415 volts, TPN bus bar 200 Amps rating and earth bus and din rail including 01 No. MCCB 3 pole 415 volts, 50 Hz, 100Amps 10 KA breaking capacity as incomer complete all as specified and as directed by Engr-in-Charge.

S&F in replacement of MCB single pole and neutral 40 /63 Amps 230 volts 'B' series complete all as specified and as directed by Engr-in-Charge.

S&F in replacement of MCB signle pole 5-32 Amps 230 volts 'B' series complete all as specified and as directed by Engr-in-Charge.

S&F in replacement MCB, DB , SPN 8 way suitable for single phase 240 volts with 100 Amps rated bus bar, double door type suitable for mounting incoming and outgoing MCB's single/double pole complete all as specified and as directed by Engr-in-Charge.

S&F edgelite LED slim Panel having white powder coated extruded Aluminum body with high quality LGP and PMMA diffuser, separate 1+PF driver 2X2 item code PMDD401018 PCGLP ECO 40 watt. Make: Polycab or equivalent model in Bajaj/CG complete all as specified and as directed by Engr-in-Charge.

Supply, laying and testing in replacement of cable XLPE insulated screened, PVC bedded galvanized steel strip or wire armoured electric power cable (heavy duty) with aluminium conductor 1100 Volts grade cross sectional area 3.5 core x 50 Sq mm. complete all as specified and as directed by Engr-in-charge. Note : Provision of suitable double crimpped lugs and glands shall deemed to be included in quoted rates.

Returning filling in including spreading, leveling, watering and well ramming in layers exc 25 cm thick complete all as specified and as directed by Engr-in-charge.

Supply and filling river sand in trenches including spreading for cushioning of LT UG cable complete all as specified and as directed by Engr-in-charge. Note : Punned down thickness shall be measured and paid .

M&L for sub class ‘B’ bricks old size laid flat dry in trenches over cable, across the direction of cable complete all as specified and as directed by Engr-in-charge.

S&F new generation Energy saving LED Flood light, powder coated PDC aluminium body with toughened glass visor fitted in frame equipped with secondary optical lens for superior Light distribution of 250Watt complete all as specified and as directed by Engr-in-charge. Cat Part No. PAR0209019 ad PCFLF C301250 HL-LFL Make: Polycab or equivalent model in Bajaj/Phillips/ Havells.

S&F MCB DP with steel enclosure 2 Module of 40 Amps, 10 KA Cat Part No. DHMCCDPF040 make: Havells complete fitted in wall complete all as specified and as directed by Engr-in-charge.

Supply, laying and testing in replacement of cable XLPE insulated screened, PVC bedded galvanized steel strip or wire armoured electric power cable (heavy duty) with aluminium conductor 1100 Volts grade cross sectional area 4 core x 16 Sq mm. complete all as specified and as directed by Engr-in-charge.

M&L for Boring of holes under road, pavement, hard standing by trenchless technology using ultra sound technique and necessary machine including HDPE pipe of 150 mm dia suitable for 0.4 mpa working pressure complete all as specified and as directed by Engr-in-charge.

Supply and lay in trenches /under roads/ crossing or fixed to wall/ pole, GI tubing light grade of size 40mm bore for protection of UG cables complete all as specified and as directed by Engr-in-charge.

Supply, fixing and erection steel tubular swaged pole type 410SP-31(9 Mtr long) complete with CI base plate,taper plug,bolts,nuts,and screws etc duly painted internally and externally with metal oxide anti corrosive paint before errection and painting with two coats aluminium paint after erection complete all as cofirming to IS 2713 (part-1 to 111) and complete all as specified and as directed by Engr-in-charge.

M&L for Foundation for Tubular swaged pole type including excavation , getting out, pole foundation with PCC (1:4:8) type D 2 (using with 40 mm graded crushed stone aggregate). Coping of pole with PCC (11:3:6) type C ( using with 20 mm graded stone agregate) and removing surplus soil to a distance n.exc 50 m and making good surface complete all as specified and as directed by Engr-in-charge.

Supply and Fix pole box weather proof street light junction box of size 250 x 140 x 95mm and connecting terminals 4 way including 06 Amps SP/MCB and fixing with street light poles using necessary MS clamps, nuts, bolts washers, lugs for incoming and out going cables, gland for cable etc of suitable size complete all as specified and as directed by Engr-in-charge. Make : Hensel/Sintex/Universal Switch Gear control.

Material and labour for PVC flat twin core 2.5 sq mm aluminium wire 1100 volt grade laid in 20 mm dia medium grade rigid PVC conduit (and fixing brackets on PCC pole) from Loop-in-loop out junction box to light fitting terminal complete all as specified and as directed by Engr-in-charge. Note :- PVC conduit shall be clamped properly with suitable clamps and no extra payment shall be done on this account.

S & F LED flood light Highly efficcient made of pressure die cast aluminium Housing with aluminium Heat sink, 10 KV SPD suitable lens & toughened glass IP-66 of 200 W complete all as specified and as directed by Engr-in-charge. Make Halonix Cat Part - HLFLD - ML 10-200-CWL.

S/F LED inverter street light 60 watt with RTC HLSLD-ML04-60-cwl-inv rtc-r as per IS 10322 (Part-5/Sec-3) aluminium PDC housing , clear Toughned frount glass, suitable high afficient secoundary lens, LNM 80 certified LED 50,000 hours @ L70 IP-66 protection , voltage 140 to 270 volt, emergency time four hours Max (Battery Backup with LI-ION battary),system wattage 60 watt suitabe for mounting on upto 50mm dia pipe bracket complete all as specified and as directed by Engr-in-charge.. Make: Halonix or Equivalent Model in Bajaj/Wipro/Syska.

Supply & installation of Decorative Double arm barckatee as Per Lustre item No LI-NM-BKT 912.2 . The decorative bracket is made out of Mild steel fabrication. The mild steel tubes are joined together by means of welded joints and are fabricated to get the design . The decorative braket shall be machined and polished properly to give a smooth surface. The double arm decorative braket shall be duly pretreated and painted in UVA ray resistant PU paint in approved colour shade. The braket shall be installed on 9 mtr pole at desired hight complete all as specified and as directed by Engr-in-charge.

Chaudhary Constructions