REPAIR TO BLDG NO T-30 T-31 AT RASPUNJA MIL CAMP AND PROVN OF JAFRI WALL WITH ONE IRON GATE AT BLDG NO T-157 AND T-161 AT SAHAPUR MIL CAMP UNDER GE (CENTRAL) KOLKATA

Amount

Dismentling of AC (corrugated, semi corrugated) sheet in roof covering incl ridges complete all as specified and directed

Taking down existing roof treatment upto original roof surfaces and removing the debris from the site etc complete all as specified and directed

Dismentling wall and ceiling board (fibre, pulp, insulation) any thickness incl. cover fillet complete all as specified and directed

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Dismentling timber scantling 40 Sqcm and over in section unframed work complete all as specified and specified and directed

All as per item No. 05 here in before but fillets, rails, post rafter, purlin under 40 Sqcm in section in unframed work complete all as specified and directed

Demolition of brick work or stone masonary built in cement mortor including all quoins & jambs etc. complete all as specified and directed

Taking down cement plaster of any description on brick work or stone msonary wall including racking of joints hacking for key scrubbing down with water etc. complete all as specified and directed

Taking down chowkhats or frames with shutters (without taking off shutter from frames) of any sizes nexc 1.5 Sqm each complete all as specified and directed

All as item No. 09 here in before but exc 1.5 Sqm and nexc 4.0 Sqm each.

Demolition of cement concrete (Un-reinforced) in ground floor and paving nexc 15cm thick above or below GL complete all as specified and directed

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Dismentalling floors hearth or wall tilling including cement mortor bedding (but not backing) removing serviceble tiles to store and rubbish off the premises complete all as specified and directed

Taking up or down steel tubing 15mm dia and connection of 15mm bore complete all as specified and directed

All as per item No. 14 here in before but 20mm dia bore.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft /loose soil complete all as specified and directed.

Excavating in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundation etc. or for shafts, well , cesspits,manholes,pier holes or for laying of water supply pipe line/ UG cable etc. not exc 10 Sqm on plan and getting out in soft / loose soil. complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm as in soft/loose soil complete all as specified and directed

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point as in soft/loose soil complete all as specified and directed

M&L for Anti Termite Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and directed.

M&L for Anti Termite Treatment of voids in masonry using chemical emulsion one litre per hole, at 300mm intervals including drilling holes at 45 degree and replugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors complete all as specified and directed.

M&L for Hardcore (broken stone or boulders) of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed

M&L RCC (Nominal Mix) 1:2:4 type B-1 (Using 20mm graded stone aggreagate) as in slab, shelves, Chajja supported on walls beam & coloumns in floor roof including balconies, conopies, deck slabs & shelves complete all as specified and directed. Note: (i) Reinforcement shall be measured and paid separately under relevant item of these schedule.

Material and Labour RCC (Nominal mix) 1:1.5:3 ( Using 20mm graded crushed stone aggregates) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

Material and Labour RCC (Nominal mix) 1:1.5:3 ( Using 20mm graded crushed stone aggregates) as in Columns, pillars, piers, posts and struts complete all as specified and directed.

Material and Labour RCC (Nominal mix) 1:1.5:3 ( Using 20mm graded crushed stone aggregates) as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

M&L for PCC 1:3:6 type C-1 using 20mm graded stone agg as in bed blocks/hold fast complete all as specified and directed

Material and labour Plain cement concrete Type D2 (1:4:8) (using 40mm graded stone agreegate) as in foundation, filling and mass concrete complete all as specified and directed.

Use and waste Formwork for rough finished surfaces to the soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and as directed.

Use and waste Formwork for rough finished surfaces to the sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and as directed.

Use and waste Formwork for rough finished surfaces to sides of pillars, posts, struts, piers, columns and stanchions of square or rectangular in section complete all as specified and as directed.

Material and Labour Brick work with fly ash pulverized bricks of designation 75, class 'A', straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

M&L Brick Work with Sub-Class ‘B’ Bricks Half-Brick thick, Old Size, built in Cement Mortar 1:4, Straight or Curved on Plan to any Radius, complete all as specified and as directed.

S&F for Mild Steel work in tubular post and trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS-4923 grade Yst.-310 complete all as specified and directed.

M&L for Mild Steel Rolled sections as in main and cross beams, hip and jack rafters; wind tie; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates confirming to Fe-290 (Gde E-165) complete all as specified and directed

M&L for Mild Steel Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment confirming to Fe-290 (Gde E-165) complete all as specified and directed

S&F for MS framed work such as framed work for ornamental and intricate design, hinges, stops, hand-made sliding bolts, etc conforming to Fe.290.Gde-E-165 complete all as specified and directed

M&L for Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut of 11 to 15mm dia, and 22.50 to 30.00 cm long complete all as specified and directed

M&L for Mild Steel TMT bars 10mm dia and over, cut to length bent to shape required including cranking, bending spirally for hopping for columns, hooking ends and binding with and including mild steel wire (anealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

Supply and fix Mild Steel TMT steel bars 6mm dia and over and upto 10mm dia bars as in stirrups, spacers and binders cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete all as specified and directed.

S&F for Mild Steel Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work complete all as specified and directed.

S&F Welded steel wire fabric weight not more than 4Kg/Sqm fitted by ms nails complete all as specified and directed

M&L for Pressed steel frames for doors with one or more rebates size of frame 125 x 60 mm including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed complete all as specified and directed. Note:- Pressed Steel Frame should be filled with PCC 1:3:6 Type C-0 (Using 12.50mm graded stone aggregate) and cost of PCC shall be deemed included in quoted rate

M&L for Pressed steel frames for doors with one or more rebates size of frame 105 x 60 mm including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed complete all as specified and directed. Note:-Pressed Steel Frame should be filled with PCC 1:3:6 Type C-0 (Using 12.50mm graded stone aggregate) and cost of PCC shall be deemed included in quoted rate.

S&F 35mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides fitted to cowkhats complete all as specified and directed.

S&F for 2nd class hardwood 35mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats as specified in SSR Part-I 2009 complete all as specified and directed.

S&F for Solid PVC Door Frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening complete all as specified and directed.

S&F for Factory Made Solid PVC Moulded Door Shutter With Wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick 3D wood grain Moulded PVC Sheet Polyurethane painted on the front face & 2mm prelam PVC Sheet on back face, supplying & fixing in frame at site complete all as specified and directed.

Material & labour of 1.50mm thick power coated aluminium , three track sliding window with three nos shutters made of aluminium section as per drawing no CWE/KOL/TD-33 of section no 1F-1F including necessary jointing cleats, glazing clips, rubber neoprene packing, roller, locking arrangement, handles 2 Nos , anodised aluminium snap beading screws etc. and glazing with 4.8 mm thick tinted glass to aluminium frame work using rubber gasket where the section of frame and shutter and Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. glazing clip, fastener etc Complete all as specified and as directed. Note :- (i) All window member including fitting & fixture i.e frame, track, shutter frame, etc shall be deem to included quoted rate. Only measure opening size of window.

S&F powder coated aluminium ventilators with louvers and glazing including frame of section over all size of window 750X600mm and glazing with 4.8 mm thick tinted glass to aluminium frame work using rubber gasket where the section of frame and shutter complete with following specification. (a) Alu frames of size 45x45x1.5mm (b) Rail & Stile 45x45x1.5mm thick (c) 4.80mm thick frosted sheet glass Note:- All ventilators/louvers member including fitting & fixture shall be deemed to included quoted rate. For measurement, opening size of ventilators/louvers shall be considered.

Material and labour for drapery rod made of electric resistance welded MS pipe of 21mm dia having a coating of corrugated virgin PVC extrusion and cover with ABS plastic complete all as specified and directed.

Supply and fixing of end finials for drapery rod and including closed type stainless steel all brackets fixed on wall complete all as specified and directed.

S&F 100mm Butt hinges, extruded brass, with brass hinge pin, bright polished, complete all as specified and directed

S&F Aluminium anodised, barrel tower bolts of extruded section 200mm long complete all as specified and directed

S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy of 300mm long complete all as specified and directed

S&F Extruded aluminium alloy handles, fabricated type, anodised 150mm long complete all as specified and directed

S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, 150mm long complete all as specified and directed

S&F 300mm, ordinary mild steel rat tail rod pattern springs including roller and roller plate complete complete all as specified and directed.

M&L for 18/19 mm thick Medium density fibre board, exterior grade, fixed to timber framework with screws complete all as specified and directed.

S&F 30mm width of flaps Continous (Piano) hinges, brass, bright finish or electrogalvanised.

S&F for 40mm dia cupboard knobs fixed with nut screws and washer of wooden finish brass polished complete all as specified and directed.

S&F 300mm, ordinary mild steel rat tail rod pattern springs including roller and roller plate complete complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated/semi corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screw complete all as specified and directed

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridge, fixed with self tapping screw complete all as specified and directed

M&L False ceiling with 'E' board "Classic" , reinforced, designer series, board with HPSC of size 600 mm x 600 mm x 4 mm thick fixed on aluminium powder coated snap grid to support the boards/files with aluminium anodised main 'T' section 35mm x 23mm x 1.50mm cross tee 35mm x 23mm x 1.50mm thick and aluminium angle 25mm x 25mm x 1.40mm as on edges/sides duly suspended with 4mm dia GI hanger fixed with GI hooks 4mm dia and fastner as required at the site and applying two coats of oil bound distemper over a coat of alkali resistant primer on exposed surfaces complete all as specified and as directed.

M&L 75mm thick PCC (1:3:6) type C-2 (Using 40mm graded stone aggregate) as in plinth protection laid in panels, finish the top surfaces even and smooth without using extra cement complete all as specified and directed Note:- Construction joints will be provided at interval of 2.5m length and filled with bitumen 80/20 mix with sand in ratio of 1:3 and cost of the same shall be deemed included in quoted rate

M&L 100mm thick PCC (1:4:8) type D-2 (using 40mm graded stone aggregate) as in sub base of floor, path/hard standing complete all as specified.

M&L 25mm thick PCC (1:2:4) type B-0 (using 12.50mm graded stone aggregate) as in sub base of floor complete all as specified.

M&L joint free non skid ceramic coloured tiles 7-8mm thick (square/rectangular) area of each tile exc 0.06 Sqm but not exc 0.11 Sqm in floor set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed

M&L joint free non skid ceramic coloured tiles 8-10mm thick (square/rectangular) area of each tile exc 0.18 Sqm but not exc 0.38 Sqm in floor set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed

All as item No. 70 here in before but in skirting with and including 10mm thick rendering on fair faces of brickwork in CM 1:4 complete all as specified and directed.

M&L Heavy duty exterior vitrified tiles ( full charged) of size 300mm x300mm x 7-10mm thick as in floor with and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed by Engineer-in-Charge.

M&L glazed ceramic coloured tiles 450x300x6-7mm in vertical surfaces set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10mm thick rendering in CM 1:4 complete all as specified and directed

M&L granite slab 15 to 20mm thick of any type work table rubbed and polished in kitchen platforms, window cills and like over and including cement screed bed 15mm thick in CM (1:6) bedded and jointed with grey cement slurry and pointed with white cement mortor (1:2) using marble dust with admixture to match with shade of granite complete all as specified and directed

M&L 35mm thick pre-cast reinforced cement concrete louvres and jallies (measured solid) in cement concrete (1:2:4) type B-0 using 12.5mm graded stone aggregate including all moulding and set in cement mortar 1:4 complete all as specifieed and directed.

M&L for providing cement concrete type B-0 (Using 12.50mm graded stone aggregate) as in padding and benching & filleting all as specified and directed.

M&L for 10mm thick screed bed or bedding over roof surfaces when concrete is still green with including WPC in cement mortar 1:3 complete all as specified and directed

M&L for preparation of plastered surfaces of roof and laying 3mm thick APP (Atactic Polypropylene Polymer) modified prefabricated five layer, weight not less than 3.6 kg/Sqm water proofing membrane, black finished reinforced with non woven polyester matt laying over a coat of bituminous primer @ 0.40 Ltr / Sqm and two coats of Bitumen based UV reflective paint with aluminium finish over APP membrane. The membrane shall be laid using butane torch and sealing all joints etc all as specified in Para 11.44.5 of SSR Part I complete all as specified and as directed.

M&L for Cutting out existing cracks in concrete surfaces forming grooves of 25mm x 40mm size, cleaning the groove thoroughly with blower, applying primer coat of the mix of IPH CC Resin & Hardner in equal proportion with suitable brush to form a film on the surface of groove, filling the groove with putty made by mixing IPH CC Resin, Hardner and admixture in the proportion of 1:1:4 and finally applying the sealing coat of the same mix and in the manner primer coat is applied with following min. coverage per running metre length of groove :- Material Priming Coat Putty Filling Seal Coat Resin 60 Gms 100 Gms 40 Gms Hardner 60 Gms 100 Gms 40 Gms Admixture - 400 Gms -

M&L Rendering 15mm thick in Cement Mortar on other than fair faces of brick work or concrete surface of wall in two layer, first layer 10 mm thick in cement morter (1:4) and top layer 5mm thick in cement morter (1:4) using water proofing compound and finishing the surface even and smooth without using extra cement including necessary scafolding and saftey measures complete all as specified and as directed. . (NOTE:-WPC shall be measured and paid separately)

M&L rendering 15mm thick in CM (1:4) on fair faces of brick work or concrete surfaces finished the surfaces even and fair without using extra cement complete all as specified and directed.

M&L rendering 15mm thick in CM (1:4) on other than fair faces of brick work or concrete surfaces finished the surfaces even and fair without using extra cement complete all as specified and directed.

M&L rendering 15mm thick in CM (1:6) on other than fair faces of brick work or concrete surfaces even & smooth without using extra cement complete all as specified and directed

M&L rendering 5mm thick in CM (1:3) as in ceiling surfaces even & smooth without using extra cement complete all as specified and directed

"Supply only" liquid water proofing compound (ISI marked) complete all as specified and directed. Make:- STP NO 1/ PEDILITE(DR FIXIT)/ FOSROC/ CICO/ SIKA

M&L complete removal of existing treatment and applying 2 coat of oil bound distemper over a coat of primer including two coat (approx 1.5mm thick) of white cement based putty including preparing of old surface complete all as specified and directed.

M&L preparing newly plastered surfaces and applying 2 coat of oil bound distemper over a coat of primer including two coat (approx 1.5mm thick) of white cement based putty complete all as specified and directed.

M&L complete removal of old decorated surfaces and Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified & directed.

M&L preparing newly plastered surfaces and Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified & directed.

M&L for preparing newly plastered surfaces and finishing wall with two coat of cement based paint over a coat of alkali resistant primer complete all as specified and directed

M&L for preparation of new surfaces of wood and wood based materials of any descriptions not otherwise described over 10Cm width or girth & applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified.

M&L for preparation of old surfaces of steel or steel based materials of any description and applying one coat of synthetic enamel paint over 10 Cm width or girth complete all as specified.

M&L for preparation of new surfaces of steel and steel based materials of any descriptions not otherwise described over 10Cm width or girth & applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed

M&L Applying polymer modified cement mortar rendering 20mm thick in CM 1:3 on wall duly mixing polymer modifier "Nitobond SBR of M/s Forsoc Chemical India (Pvt) Ltd" or "Hind Styrene BR of Hindcon Chemical Ltd" or equivalent make of M/s Pidilite Industries @ 7 Litre per bag of cement complete finished even and smooth without using extra cement as per manufacturer's specification complete all as specified and directed.

S&F 40mm bore MS tubing medium grade and fixed at wall for ceiling complete all as specified and directed.

S&F for 20mm outer diameter CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed.

S&F for 25mm outer diameter CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed.

Cutting chase, pinning in making good to facing where required and pointing in CM 1:3 to end or edges of landing steps, cills, sunshades, shelves, lintels etc. and cutting chase for conceled water pipe etc. and making good cutting not exc 10Cm girth.

Supply and fixing in repair Vitreous China wash down water closet pan including P or S trap (pedestal pattern), white (excluding flushing cistern and flush pipe) including plastic water closet seat, black colour , closed pattern with flat bottom, and cover and mild steel chromium plated or aluminized hinging device and wash down water closet complete all as specified and as directed. Make-Essco (ECS-WHT-551PNPP) or equivalent from Cera/Hindware

S&F in repair vitreous china wash hand basin white of size 550 x 400mm excluding taps but including 32mm PTMT waste coupling (excluding 32mm waste pipe) complete all as specified and directed.

S&F in repair PVC flusing cistern low level 10 Ltr capacity of approved make including fixing of brackets connection to WC and making good disturbed area complete all as specified and as directed.

S&F in repair for 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to wall complete all as specified and directed.

All as per item No. 102 here in before but double socketed complete all as specified and directed.

S&F in repair PVC (SWR) bend any radius 110mm bore complete all as specified and directed

S&F in repair PVC (SWR) junction single (single T) equal or unequal 110mm bore complete all as specified and directed.

M&L in repair for diameter of outlet 75mm UPVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified and as directed

S & F in repair for 15mm bore brass chromium plated Wall Mixer with Provision for Overhead Shower with 115mm long Bend Pipe on Upper Side, Connecting Legs & Wall Flanges complete all as specified and directed.

S & F in repair for brass chromium plated Centre Hole Mixer for WHB screwed for 15 mm bore pipe complete all as specified and directed.

S & F in repair for 15mm bore brass chromium plated Angular Valve with Wall Flange complete all as specified and directed.

S & F in repair for brass chromium plated Fancy Type Bib taps for 15 mm bore pipe complete all as specified and directed.

S & F in repair for brass chromium plated two in one tap with Wall Flange screwed for 15 mm bore pipe complete all as specified and directed.

S & F in repair for brass chromium plated long body bib cock with Wall Flange for 15 mm bore pipe complete all as specified and directed.

S&F work in repair for ABS Body chrome plated shower rose 125mm size including fixing to steel pipe or union complete all as specified and directed.

S & F work in repair for shower arm 240mm long round shape with flage including fixing to steel pipe or union complete all as specified and directed.

S & F in repair for 600mm long Towel Rail chromium plated 20mm dia fixed with screw complete all as specified and directed.

S & F in repair for chromium plated Health faucet with 8mm Dia, 1.2 Meter long flexible tube and wall hook with N.R.V (Back Flow Preventer).

S&F PVC bathroom cabinet (white) of size 430 x 330 x 100 mm (approx) with one single shutter and built in mirror in front of shutter as in repair complete all as specified and directed.

S&F PVC connection 15mm size with PTMT nut of length 450mm complete all as specified and directed

S&F of sink made of stainless steel 1mm thick kitchen with plugs, washers, including bedding in cement mortor or fixing cantilever bracket and connecting union to pipe, overall size 495mmX420mm bowl size 410mmX330mmX160mm as in repair complete all as specified.

S&F stainless steel utencil plate rack (size 24'' x 30'' x 10'') using 0.8mm thick sheet as in repair complete all as specified.

S&F triple layer PVC water storage tank cylinderical, verticle with closed top hoisted and fixed in position tank capacity 1000 Ltr with and including ball valve high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for 25mm outer diameter for CPVC pipe & making connection for inlet and outlet including dismental of old water tank and removing from site complete all as specified & directed.

Taking down point wiring (light, fan, socket and power complete including fixtures and fittings such as switches ceiling roses, pendents , regulators, sockets, light fittings etc. removing materials to store for keeping in safe custody for refixing or for taking credit (credit for above items should be made as per conditions separately) and making good distrubed surfaces of walls, floors, etc. including cleaning all and specified and directed.

M&L for Point wiring with PVC insulated and unsheathed FRLSH cable single core multistranded copper conductor 1.5 sqmm size, 1100 volts grade cable conforming to IS - 694 1990 drawn through and including PVC concealed conduit 20mm dia medium duty with all accessories including fabricated 1.6 mm thick MS terminal boxes fixed flush with wall surface with 3 mm thick plastic masonite laminated sheet top cover fixed with cadmium screw for mounting switches, sockets, regulator etc including 1.5 sq mm FRLSH stranded PVC insulated and unsheathed copper conductor earth continuity conductor to common earth and connecting to earth dolly includingCutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 all as specified for one light or fan point controlled by one switch single pole one way for light/ ceiling fan/ exhaust fan/call bell point/ Switch socket outlet 5 amps complete all as specified and as directed.

All as per item No 123.00 here-in-before but one 3 pin 5 amps socket outlet on the same board with other switch complete all as specified and directed by Engineer-in-charge.

All as per item No. 123.00 here-in-before but one 3 pin 5 amps switch socket outlet on the independent board with other switch complete all as specified and directed by Engineer-in-charge.

M&L Point wiring with 2.5 sqmm (Nominal Area) PVC insulated stranded single core unsheathed FRLSH copper conductor cable 1100 Volts grade drawn through with and including PVC concealed conduit 20mm dia medium duty with all fittings and accessories of casing caping (like Tee, Bend etc) complete fixed to walls / ceiling etc with and including 2.5 Sqmm (nominal area) PVC insulated unsheathed, stranded, single core FRLSH copper cable as earth continuity wire connecting to common earth point (including supply & fixing of 1.6 mm thick pressed mild steel terminal boxes of suitable size with 3 mm thick PVC /plastic laminated sheet, top cover suitable sizes of brass screws and washers etc. including Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3for mounting sockets for 5 pin, 16 Amp socket outlet on independent board complete all as specified and directed.

All as per item No.126.00 mentioned here-in-before but using 4.0 sq mm size stranded copper conductor cable for one AC starter including 4.0 sq mm FRLH/S PVC insulated unsheathed stranded copper conductor as earth lead and connected to common earth doly complete all as specified and directed by engineer incharge.

S&F A C starter unit consisting of one 25 Amp capacity starter, one 240 V 25 Amps 10 KA SPN MCB, one 25 Amps socket and one 25 Amps plug top prewire complete all as specified and directed by Engineer-in-Charge.

S&F Switch piano, flush type, SP, one way, 5/6 Amps 230/240 Volts, white/ivory finish complete all as specified and directed.

S&F Switch socket combination multipurpose 2 in 1, 3 pin 6 Amps 230/240 volt flush type complete all as specified and as directed.

S&F Socket outlet 3/5 pin, 6 Amps, 240 volt flush type complete all as specified and as directed.

S&F Switch socket combination multipurpose 2 in 1, 3 pin 15 Amps 230/240 volt flush type complete all as specified and as directed.

S&F bell push switch, flush type 5 Amp complete all as specified and as directed.

S&F Call bell, ding dong AC 230 volts, single pole as in repair complete all as specified and as directed.

S&F Ceiling rose surface bakelite three terminals 240 volts complete all as specified and as directed.

S&F Ceiling Fan regulator step type 240 Volt complete all as specified and directed by the Engr-in-Charge.

S&F lamp holder insulated body with back plate for batten fittings complete all as directed.

S & F LED bulb 9Watts 240V 50Hz 6500K b22 base in bulb holder complete all as specified and directed by Engineer-in-Charge.

S&F Energy efficient LED fittings of capacity 10W suspended type / wall mounted type complete with LED tube Lamp and fitting with copper flexible PVC cable of 0.50 sq mm twin core not more than one metre in length complete all as specified and as directed.

S&F Energy efficient LED fittings of capacity 20W suspended type / wall mounted type complete with LED tube Lamp and fitting with copper flexible PVC cable of 0.50 sq mm twin core not more than one metre in length complete all as specified and as directed.

Taking down unserviceable rusted / damaged MCB DBs of any type and way along with any type MCB and keeping serviceable MCB in safe custody in re-use in the work and making good to the distubed surfaces of walls etc. complete all as specified and as directed.

S&F Sheet metal enclosure for DB's when MCBs to be used 8 way single pole and neutral double door with 200 amps rated bus bar complete 240 volts complete all as specified and as directed.

S&F MCB 6 to 32 Amps, SP, 240 Volts , 'C' curve breaking capacity 10 kA complete all as specified and as directed.

S&F MCB 40 to 63 Amps, DP 240 Volts ,C- Curve breaking capacity 10 KA including necessary connection complete all as specified and as directed.

Taking down old burnt/unserviceable submain wiring with aluminum/copper conductor PVC insulated cable of any size drawn through PVC casing caping/ PVC Conduit pipe including GI wire accessories etc. and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

M&L Sub main wiring with 2 runs of single core FRLSH type PVC insulated unsheathed stranded copper conductor of size 10.0 Sqmm and one run of PVC insulated unsheathed multistrand copper conductor FRLSH type of size 10.0 Sqmm as earth lead drawn into rigid non metalic PVC conduit of size 20 mm dia including all fittings complete all as specified and as directed. Note:- Two runs of 10 Sqmm conductor as main wire and one run of 10Sqmm conductor as earth wire with one run of PVC conduit shall be measured as one unit.

Taking down and refixing of ceiling fan of any sweep at its original/ other position including provision of cable from ceiling rose to fan complete all as specified and as directed.

Taking down and refixing of electric water heater of capacity 25 litre complete with pressure reducing valve and all accessories such as safety valve, thermostate, NRV, connection piece etc. at its original/ other position complete as directed.

S&F building security light pressure die cast housing with individual LEDs with modular secondary optics security light luminaires 35 watt LED with 50mm dia light grade GI pipe bent to shape of 45'' 1.5 mtr long and nuts bolts including fixing arrangement after taking down old unserviceable one complete all as specified and directed by Engineer-in-Charge.

Materials and labour Earthing complete with galvanised steel earth plate electrode 60 Cm x 60 Cm x 6.00 mm thick buried in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate not less than 1.5 m below normal ground level, connected to GI wire 4 mm as earthing lead by means of bolts, nuts, check nuts and washers of GI or steel, GI strip projected by 40 mm bore light grade GI pipe and other end connected to earth test point as directed including funnel with watering pipe 20 mm bore light grade galvanised iron, wire mesh, charcoal or coke common salt laid in alternative layer of 15 cm (complete thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C-1, 50 mm thick pre-cast RCC (1:2:4) type B-1 normal mix cover slab reinforced with 8 mm dia TMT bar 10 Cm c/c both ways and single handle of 10 mm dia round bar including necessary excavation, earth work etc. in soft / loose soil and disposal pf soil to a distance n. exc. 50 m and necessary testing on completion all as shown in electrical plate No. 3 MES Schedule Part-I including taking out of old unserviceable earth pit with all accessories complete all as specified and as directed.

Supply and Laying Steel Water Tubing 80mm Bore (dia), Galvanised, ‘light Grade’ with all Fittings, fixed in trenches or any other Situation, complete as all specified and as directed.

Supply and Laying Steel Water Tubing 20mm Bore (dia), Galvanised, ‘Medium Grade’ with all Fittings, laid in trenches or any other Situation, complete as all specified and as directed.

Supply and Laying Steel Water Tubing 25mm Bore (dia), Galvanised, ‘Medium Grade’ with all Fittings, laid in trenches or any other Situation, complete as all specified and as directed.

Supply & fixing gun metal 20mm bore gate valve including taking out the U/S old one (ISI marked) screwed down high pressure with handle with iron wheel both ends screwd for iron pipe of the following size.

Supply & fixing gun metal 25mm bore gate valve including taking out the U/S old one (ISI marked) screwed down high pressure with handle with iron wheel both ends screwd for iron pipe of the following size.

Supply and laying dry coarse sand as in cushioning of under ground electric cable in trenches, laid to a uniform thickness of 23 Cm (15 Cm under the cable & 8 Cm over the cable) and gently punned down to 18 Cm thickness complete all as specified and as directed by the Engr-in-Charge. Note:- Thickness after punning down shall be measured for payment.

Materials and Labour Cutting /boreing of existing road / path , hardstandingetc for taking out cable and water pipe to protection with iron cover plate for passing cable,water pipe and making good the disturbed road top surfaces with following cement concrete all type, using of suitable depth and finished with speed breaker complete all as uder directed by Engineer-in-Charge.

M&L Cutting drilling and tapinge existing CI/DI water mains in position, for addn/altrn or for taking branch connection/insertion of pipe specials, valve of 25 to 80 mm bore pipe complete all as directed by Engineer- in- charge.

Supply and laying in trenches Bricks, sub class 'B' over burnt (kiln burnt) old size bricks, laid flat dry with width of the bricks laid to the axis of the cable for protection of cable complete all as specified and as directed by the Engr-in-Charge.

Laying only bricks in trenches except Bricks, laid flat dry with width of the bricks laid to the axis of the cable for protection of cable complete all as specified and as directed by the Engr-in-Charge.

Taking out unserviceable UG cables of any type and any sizes from trenches etc and removing from the site of work complete all as specified and directed. Note:- (i) Serviceable bricks obtained shall be stacked properly for re-use. (ii) Excavation and earth work shall be measured and paid separately under relevant item of these schedule.

Supply and laying XLPE insulated PVC sheathed, armoured, aluminium conductor cable 1100 Volt grade 16 Sqmm 4 core in trench/duct/floor/wall with provision of saddle and lugs, joints etc including connection complete all as directed by the Engr-in-Charge.

SMART CONSTRUCTION (BID ID -3317355)

JOY RAM ENTERPRISE (BID ID -3317167)

CIVCON (BID ID -3317719)

G D TRADERS (BID ID -3316964)

BIKASH CHANDRA NEOGI (BID ID -3317551)

M/S P K CONSTRUCTION (BID ID -3317687)

NARAYAN BUILDERS (BID ID -3317761)