SPL REPAIRS TO BLDG NO P 21 OFFRS MESS AT SUKNA MIL STN AND OTHER SANCTIONED WORKS AT SUKNA MIL STN OF AGE BR II UNDER GE SUKNA

Amount

M & L for sand filling under floors or in foundations including watering and consolidation as required complete all as specified and directed.

M&L for PCC 1:3:6 type C-1 (using 20 mm graded stone aggregate) as in surface channel and drain complete all as specified and directed.

M&L PCC 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate) as in copings, bed plates, bed block for holdfasts, filling in pressed steel door frames, wall of drains, benching, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating and including necessary formwork complete all as specified and directed.

M&L providing precast reinforced cement concrete 1:2:4 type (using 20 mm graded crushed stone aggregate) in lintel upto 1.5 m clear span and other similar bandand bed plate, manhole coverand drain cover complete all as specified and as directed.

Supply only integral water proofing compound complete all as specified and directed.

M & L for brick work with sub class ‘B’, old size brick straight or curved on plan exc. 6.00 m mean radius built in cement mortar 1:6 complete all as specified and directed.

Cutting chases, pinning in, making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, lintels, shelves etc, and cutting chases for concealed water tubing or concealed conduit wiring etc, and making good on brick walls, cutting n.exc. 10 cm in girth complete all as specified and directed.

M & L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with granite shade over 20 mm thick screed bed in CM (1:6) complete all as specified and directed.

Use and Waste of formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter for rough finished flat surfaces of concrete complete all as specified and directed.

S&F 2nd class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

S & F 35 mm thick Second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut mitred beads for securing glass etc. size of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) fitted to chowkhats complete all as specified and directed.

S & F factory made Solid PVC door frame of size 50 mm X 47 mm made out of 5 mm plain coloured PVC sheet reinforced with mild steel square tube as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

Taking down chowkats or frame n.exc 1.5 Sqm each with shutter (without taking off shutter from the frame) complete all as specified and directed.

Taking down chowkats or frame but exc. 1.5 Sqm but not exc. 4.0 Sqm each with shutter (without taking off shutter from the frame) complete all as specified and directed.

S & F 30 mm thick (style thickness) factory made solid panel PVC shutter consisting of frame made out of mild steel tubes for top and bottom rails, mild steel frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side & as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles and rails with suitable PVC sheets beading and joined together with solvent cement as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S & F of 150 mm long Aluminium anodised barrel tower bolts, of extruded section complete all as specified and directed.

S&F 300 mm long mild steel sliding door bolt, plate type, stove enameled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.

S&F 100 mm Aluminium butt hinge, medium weight, complete all as specified and directed.

S&F 300 mm, ordinary rat tail rod pattern springs and including roller and roller plate complete all as specified and directed.

S&F 150 mm Aluminium handles cast type, anodised and fixed complete all as specified and directed.

S&F 40 mm continuous (piano) hinges, mild steel, bright finish or electrogalvanised complete all as specified and directed.

Supply and fix in repairs mortice lock suitable for aluminium door of 100 mm size 4 lever brass body vertical type as per existing or sample complete all as specified and directed.

S&F in repairs 20 mm dia harrison rail, mild steel, chromium plated with & includig suitable fixing CP brackets, stops, rollers etc. complete all as specified and directed.

S&F in repair 150 mm floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S&F in repairs Door closer hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000mm in width of aluminium (Die cast) body complete all as specified and directed by Engr-in-Charge.

S & F in repairs galvanized mild steel wire cloth, 0.56 mm dia of wire and average width of aperture 1.18 mm and fixed with tinned stacks, or galvanized wire staples including wooden beads complete all as specified and directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or stainless steel wire staples complete all as specified and directed.

S&F in repairs decorative curtain rod of wooden finish powder coated of 25 mm dia including 06 nos. curtain ring per running metre complete all as specified and directed.

S&F in repairs decorative type wooden finish double brackets support for holding curtain rods and corner to be fixed to ends of curtain rod fixing with screws complete all as specified and directed.

S & F of mild steel framed work such as grills, gratings etc. with ends of bars shouldered and / or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railing, frame work of water tanks and similar work conforming to Fe – 290 Gde E -- 165 complete all as specified and directed.

S&F rolled mild steel in plates, gusset plate (plain or chequered) channels square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe-410W (Gde-E-250) quality-A complete all as specified and directed.

S & F of roof trusses (framed), trussed, purlins, crane gantries, rails, fastening and heavy bracket framing (Beam, tee, angle, channel or flat sections), including distance pieces, cleats etc. confirming to Fe – 410 – W(Gde E - 250) quality 'A' complete all as specified and directed.

S & F Steel windows with side hung shutters including box type hinges with steel handle and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S & F Steel windows with side hung shutters including box type hinges with steel handle and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified and directed.

S & F Steel ventilator with top hung shutters including hinges, steel peg stay, complete all as specified and directed.

S & F of pressed steel frame of size 105 X 60 mm for doors with one or more rebates including filling of cement mortar or cement concrete necessary fixing lugs, hinges, lock strike plates and applying two coats of synthetic enamel paint over one coat of red oxide primer etc complete all as specified and directed.

S&F 35mm thick flush shutters, solid core construction, with MDF board and plywood faces panels, commercial type on both side complete all as specified and directed

M&L powder coated Aluminium door, window, Cup board and ventilator shutter and frame any type (Sliding or openable ) with frame and other similar work, fabricated aluminium mesh etc. aluminium heavy section favricated incl all necessary roller wheels, cleats, handle, locking arrangement and arrangement to fix wire mesh with aluminium channel beading and stainless steel screw incl cost of rubber gasket ,beading roller wheel etc. ,complete all as specified and directed. Note: (a) The weight of rubber gasket beading, roller wheels, etc will not be measured with the weight of aluminium shutters as only aluminium items shall be measure. (b) Wire mesh shall be measured and paid separately. (c) Aluminium hinges shall be included in the unit rate

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm TCT (total coated thickness) of any colour having tensile strength of 550 Mpa as in roof covering cladding to wall etc, fixed with self tapping screws of any descriptions complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm TCT (total coated thickness) of any colour having tensile strength of 550 Mpa as in roof covering cladding to wall etc, fixed with self tapping screws of any descriptions complete all as specified and directed.

M & L in repairs 18/19 mm thick prelaminated Particle board, interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with screws to timber frame work with teak wood beading at the edges complete all as specified and directed.

M&L 18-20 mm thick granite slab(of any type) tiles machine cut, bedded jointed with grey/ colored cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone as in cladding, jambs, cills, including grinding, polishing, moulding & over & including 15mm thick screed bed in CM 1:4, complete all as specified and directed.

M&L rounding to edges of stone slabs one edge, such as in steps, cooking platform and other similar situations complete all as specified and directed.

M&L 75 mm thick, PCC 1:3:6, type C-2 (using 40 mm graded crushed stone aggregate) as in sub base, floors, paths, plinth protection, hardstanding etc. finished even and smooth without using extra cement complete all as specified and directed.

M&L 75 mm thick, PCC 1:4:8, type D-2 (using 40 mm graded crushed stone aggregate) as in sub base finished even and rough complete all as specified and directed.

M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but n. exc. 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 20 mm thick in CM 1:6 complete all as specified and directed.

M&L 10 mm thick double charged premium quality coloured vitrified ceramic tiles (square / rectangular) polished, area of each tiles n. exc. 0.36 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 20 mm thick screed bed in CM 1:6finish even and rough complete all as specified and directed.

M&L 10 mm thick double charged premium quality coloured vitrified ceramic tiles (square / rectangular) polished, area of each tiles n. exc. 0.36 sqm in skirting/dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 10 mm thick screed bed in CM 1:3 complete all as specified and directed.

M&L coloured glazed ceramic tiles 350x250x7 / 450 x 350 x 7 mm thick as in dado / skirting and vertical surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 10 mm thick screed bed in CM 1:3 including roughening of surface complete all as specified and directed.

M&L machine cut kota stone flooring 20 mm (minimum) thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab and including rubbing and polishing and laid over 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L machine cut kota stone 10 mm (minimum) thick as in skirting, dado, riser of steps, plinth, etc, laid over and including 10 mm thick screed bed in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the stone and including rubbing / grinding and polishing complete all as specified and directed.

M&L 60 mm thick machine pressed precast concrete interlocking coloured paver block of any shape and size confirming to IS 15658-2006, M-35 grade, set with grey cement and pigment, laid over and including 15 mm thick screed bed in CM 1:6,complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing the rubbish off the premises complete all as specified and directed.

Taking down cement plaster on brick or concrete surfaces / ceiling, racking out joints hacking for key scrubbing down with water etc complete all as specified and directed.

M & L for 15 mm thick rendering in cement mortar 1:6 on other than fair faces of brick work or concrete surfaces and finished the surface even and smooth without using extra cement complete all as specified and directed.

M & L for 15 mm thick rendering in cement mortar 1:4 on fair faces of brick work or stone masonry or on one side of lathing surfaces and finished the surface even and smooth without using extra cement complete all as specified and directed. Note:- WPC shall be measured and paid separately.

M&L for rendering 5 mm thick rendering in CM 1:3 on ceiling finished even and smooth without using extra cement complete all as specified and directed. Note: The rate are inclusive of necessary scaffolding.

M&L for repair to broken/damaged RCC chajjas by making good with PCC 1:2:4 type B1 or rendering 15 mm thick in cement mortar 1:4 mixed with water proofing compound to top and sides and rendering 5 mm thick to soffits in cement mortar 1:3 including necessary form work, reinforcement duly welded if required including demolition of broken/loose PCC or taking down old plaster at any storey of building complete all as specified and as directed. (Note: Rate shall be included for necessary scaffolding and safety arrangement)

M & L for preparation of newly plastered or previously untreated surfaces of walls and applying two coats of oil bound distemper over a coat of primer and over a thin layer of wall care putty to obtain smooth finish complete all as specified and directed.

M&L complete removal of existing treatment of old decorated wall surfaces and including applying two coats of oil bound distemper over a coat of primer and over a thin layer of wall care putty to obtain smooth finish complete all as specified and directed.

M&L preparation of new plastered wall surfaces and inlcuding applying two coats of weather coat exterior paint over a coat of primer and over a thin layer of wall care putty to obtain smooth finish complete all as specified and directed. (Note: rate shall be included for necessary scaffolding and safety arrangement)

M&L complete removal of existing treatment of old decorated wall surfaces and including applying two coats of weather coat acrylic exterior emulsion paint over a coat of primer and over a thin layer of wall care putty to obtain smooth finish complete all as specified and directed.

S & F Sheet glass 3.0 mm thick, ordinary quality and glazing with oil putty or wooden beads not exceeding 0.5 Sqm in each pane glazed with putty or fixed with beads complete all as specified and directed.

S & F 3 mm thick figured glass, pin headed type and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane complete all as specified and directed.

S&F 4.8mm thick glass including tinted/dark film n exc 0.5 sqm each pane complete fixed to aluminium frame work including rubber beading complete all as specified and directed.

S&F 4.8mm thick glass including tinted/dark film exc 0.5 sqm each pane complete fixed to aluminium frame work including rubber beading complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed.

M&L preparation of new steel surfaces of any description, not otherwise described over 10 cm width or girth and including applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for preparation of old painted steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

Taking down or up 15 mm bore steel tubing and connections, complete all as specified and directed.

Taking down or up 20 mm bore steel tubing and connections, complete all as specified and directed.

S&F 15 mm bore galvanised steel water tubing medium grade and including necessary GI fitting (such as bends, elbows, tees etc. and fixed to wall / ceiling or laid in / on floor complete all as specified and directed.

S&F 20 mm bore galvanised steel water tubing medium grade and including necessary GI fitting (such as bends, elbows, tees etc. and fixed to wall / ceiling or laid in / on floor complete all as specified and directed.

S&F in repairs sink with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915 x 460mm bowl size 405 x 355 x 178 mm and including 32 mm waste pipe & coupling complete all as specified and directed.

S&F in repairs vitreous china european wash down water closet pan (pedestal pattern) white in colour with fixing bolts and flush pipe, connection to trap and to flushing cistern and all joints, including plastic water closet seat cover white, closed pattern with flat bottom and cover and mild steel CP hinges complete all as specified and directed.

S&F in repair vitreous china wash hand basin, oval type of size 580x450mm white including waste coupling, waste pipe granite counter complete all as specified and directed.

S&F in repair PVC low level flushing cistern of 10 litres capacity, valve less, syphonic action type, white body, with inlet ball valve, float and handle including brackets complete all as specified and directed.

S&F in repairs shower arm 15 mm size,450 mm long with bend of 90 degree with flange of PTMT any colour (minimum weight 40gms) complete all as specified and directed.

S&F in repairs 120 mm size swivel shower rose of ABS, chromium plated with long head arm for fixing with 15 mm pipe complete all as specified and directed.

S&F in repairs 15 mm bore bib taps, two way, chromium plated, fancy type, cast copper alloy with crutch or butterfly handle and wall flange, screwed for iron pipe or for brass ferrule & fixed complete all as specified and directed.

S&F in repairs angle stop cock 15 mm bore, cast copper alloy, screwed down high pressure, with crutch of butterfly handle, screwed both ends for iron pipe or unions and fixed, fancy type, chromium plated long thread with flange complete all as specified and directed.

S&F in repairs 15 mm bore bib tap chromium plated fancy type, cast copper alloy with crutch or butterfly handle, screwed for iron pipe or for brass ferrule & fixed complete all as specified and directed.

S&F in repairs stainless steel toilet paper holder with flat recessed type complete all as specified and as directed. Make:- Jaquar/Hindware (QUEO & Italian Collection) / Prayag (D’OR Series) / Cera (Premium / Luxury Range)

S&F in repairs , wall mixer brass chromium plated for mixing 'hot' and 'cold' water with connection to overhead shower with 115mm long, bend pipe and wall flanges, screwed down for iron pipe and fixed for 15mm bore pipe complete all as specified and directed.

S&F in repairs central hole basin mixer, brass, chromium plated, for mixing hot and cold water, with 450 mm Long Braided Hoses, screwed down for 15 mm bore pipe complete all as specified and directed. Make: Jaquar Cat Part No. 167 KNB or equivalent in MARC, Hindware

S&F in repairs ball valves 20mm dia high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 20 mm - 210 gms) complete all as specified and directed.

S & F of 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls/ floors complete all as specified and directed.

S & F of 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls/ floors complete all as specified and directed.

S&F in repairs 75 mm bore PVC (SWR) floor trap, plain with grating and including jointing with solvent cement complete all as specified and directed.

S&F PVC (SWR) 110 mm bore bend, of any radius complete all as specified and directed.

S&F PVC (SWR) 75 mm bore bend, of any radius complete all as specified and directed.

S&F 110 mm bore PVC (SWR) vent cowl of any radius complete all as specified and directed.

S&F in repairs health faucet 15 mm bore, ABS chromium plated with & including 1.0 mtr chromium plated flexible tube & wall hook including CP nipple and socket complete all as specified and directed.

S&F in repair acrylic assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated brackets guard and railing 60cm long sixed fixed with and including plated brass screws (600mm long) complete all as specified and directed.

S&F in repair corner self of glass fixed with and including plated brass screws complete all as specified and directed.

S&F in repair stainless steel towel rings chromium plated fixed with and including chromium plated brass screws and wooden / plastic cleat complete all as specified and directed.

S&F in repair towel rail 20 mm dia & 600 mm long of chromium plated fixed with and including chromium plated brass screws and wooden / plastic cleat complete all as specified and directed.

S&F in repair soap dish with metal dish of chromium plated fixed with and including chromium plated screws and wooden / plastic cleat complete all as specified and directed. Make : Jaquar UF-0913 or equivalent in MARC, Hindware

S&F in repairs 75mm dia stainless steel gratings, doom type, chromium plated, with or without waste hole, fixed to floor trap complete all as specified and as directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and directed.

M&L for dismantling of stone slabs and tiles of any description or thickness in floors, aprons, etc complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n. exc. 15 cm thickness (below or above ground level) complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc. complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness including Nainital or similar pattern roof covering complete all as specified and directed.

Demolition and breaking up drain pipe of internal dia 100 mm (salt glazed ware, AC or reinforced concrete) set in cement mortar complete all as specified and directed.

S&F VTPN DB, MCCB incomer, 4 ways double door,Metal door ,IP-43 IK 09 in 250A rated copper bus bars,earth bar,neutral links, no. of module DPX 250+12 complete incl. blanking plates as required & fixed flush to wall and making good the disturbed surfaces including taking down old unserviceable ones complete all as specified and as directed.

S&F MCCB 4P 125 Amps 415V ,50 Hz ,breaking capacity 25 KA . Including dismantling taking down unserviceable one complete all as specified and as directed.

S&F MCB ,SPN DB, 8 ways double door,Metal door, IP-43 IK 09 in 100A rated bus bars,earth bar,neutral links complete incl. blanking plates as required & fixed flush to wall and making good the disturbed surfaces complete all as specified and as directed including dismentling taking down unsvericeable one complete all as specified and as directed.

S&F MCB SPN 40 Amps 240V ,50 Hz ,breaking capacity 10 KA," C " series. Including dismentling taking down unsvericeable one complete all as specified and as directed.

S&F MCB SP,10KA, 230V, C-curve, 6-32 amps including dismantling taking down unserviceable one complete all as specified and as directed.

S&F in replacement 1 x 15 watt LED post top lantern, IP-65, die cast aluminium housing, opal diffuser, electronic driver fixing arrangement etc complete all as specified and directed.

M&L for Earthing complete with galvanized steel earth plate electrode 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 meter below normal ground level, connected to galvanized iron earth lead wire of 4 sqmm by means of bolts, nuts, check nuts and washers of galvanized iron or steel, all as shown in Electrical Plate No 3 of SSR Part - I, including necessary excavation and earth work, P.C.C (1:3:6) type C-I with 50 mm thick Pre-cast R.C.C. (1:2:4) type B-I cover slab (reinforced with 8 mm dia deformed bar @ 15 cm C/C both ways and suitable handle of 10 mm dia round bar), including providing charcoal or coke and common salt in alternate layers of 15 cm compacted thickness all around the earth electrode, with funnel and 20 mm bore galvanized iron watering pipe (light grade), wire mesh, aluminium lugs, complete in all respect, GI earth wire protected by 15 mm bore (medium grade) galvanized iron pipe and other end connected with main switch board or Earthing test point as directed, including necessary earth work and disposal of spoil to a distance not exceeding 50 metre and necessary testing on completion including dismentaling old unsv ones complete all as specified and as directed by the Engineer-in-Charge.

R N SAH N CO (BID ID -3042834)