Construction of 2 Nos D-Type Qtr for A.E.E., R.W. Sub-Division, Kalimela and A.E.E., R.W. Sub-Division, Podia in the District of Malkangiri for the year 2024-25.

Earthwork excavation in hard soil with all leads & lifts including rough dressing &levelling bed & depositing the excavated material away from the working site as directed by Engineer in charge.

Filling foundation & plinth With sand well watered and rammed etc complete as directed by the engineer-in-charge.

Providing cement concrete (1:3:6) with nominal size stone aggregates for CC works including all cost etc. complete as directed by the engineer-in-charge.

RCC work of M-20 grade with 20mm and down graded black hard granite (C.B) stone chip[s including hoisting and laying. as directed by the Engineer-in-charge. Column/Footing/Base Ground Floor

Columns up Plinth beam bottom

Plinth Band Portico

Column

RCC Lintel

Stair case

RCC Chhajah

Roof Beam

Roof Slab

Head Room

Column

RCC Lintel

RCC Chhajah

Roof Beam

Roof Slab

RRHG stone masonry in CM(1:6) in foundation and plinth including all cost of materials etc. complete and as directed by the Engineer-in-charge.

Cutting, bending, binding of MS rods and tying the grills and placing in position including cost of steel and binding wire and as directed by the Engineer-in-charge.

Ground Floor

Head Room

CB Brick masonary in CM(1:6) including all cost of materials etc. complete and as directed by the engineer-in-charge.

Ground Floor

Head Room

20mm thick cement plaster (1:4) over wall top including all cost etc. complete and as directed by the Engineer-in-charge.

Ground Floor

Head Room

12mm thick CP in CM(1:4) over wall top including all cost etc. complete and as directed by the Engineer-in-charge.

Ground Floor

Head Room

16mm thick CP in CM (1:6) including all cost of materials etc. complete and as directed by the Engineer-in-charge.

Ground Floor

Head Room

Providing and fixing of WPC door frames with rebate cuts and finished cross section size 75mm x 45mm or 90mm x 50mm, including cost of all materials, cost of all labour conveyance, taxes, loading, unloading scaffolding, slaging watering and curing, T&P, etc, complete as per the direction of the Engineer-in-charge.

Ground Floor

Supplying , fitting & fixing of 32mm thick flush door shutter with approved quality of 30mm thick BWR block board pasted with 1mm thk laminate on both side of approved design and quality including cost of all door fittings and fixtures etc, complete.

Door Chaukat with shutter made out of MS angles and sheet including all cost etc. complete and as directed by the Engineer-in-charge. Head Room

Window Chaukat with shutter made out of MS angles and sheet including all cost etc. complete and as directed by the Engineer-in-charge. Ground Floor

MS grill gate etc. including all cost etc. complete and as directed by the Engineer-in-charge.

Ground Floor

Head Room

Supplying, fitting, fixing of fully glazed aluminium door with OEL anodised AI door section of 9202 as vertical member, 9201 as top member and 9200 as bottom and middle member and 12mm thick pre-laminated board fixed on door frame by means of tapered clip No.4660 and the frame to be completed by means of jointing angle No.1855 including all cost of labour, T&P, hire charges of drilling machine, labour charges etc complete.

Supplying, fitting, fixing of fully glazed aluminium sliding windows using 15 micron anodised OEL aluminium section 2080 as out section, 9139 as mullion section, 4124 as a shutter setion frame with tappered clip of section 4125, aluminium angle, rubber breading friction stay and handle etc with 5mm thick glass.

in floors, treads or steps and landing on 25 mm thick bed of cement mortar (1:1) jointed with neat cement slury mixed with pigment to match the shades of the tiles including rubbing and polishing complete including cost of precast tiles as directed by the Engineer-in-charge.

Providing and fixing Ceramic tiles in dados, skirtings and risers of steps on 12mm thick cement plaster (1:3) jointed with neat cement slury mixed with pigment to match the shades of the tiles including rubbing and polishing complete including cost of precast tiles as directed by the Engineer-in-charge.

Skarting

Chequered tile steps trade ,riser

Providing fitting and fixing of false ceiling with Aluminium anodised T-Section no 3115 with 2'0" center to center L-Section no. 1705 up to 15 micron on 4 wall to be fixed by means of steel screw and PVC plug and the aluminium etc complete.

Finishing wall surface with Acrylic wall putty (water based) of approved make including all cost etc. complete and as directed by the Engineer-in-charge.

Ground Floor

Head Room

Painting two coat to the new surface of iron work with one coat primer including all cost of paint primer etc. complete and as directed by the Engineer-in-charge.

Ground Floor

Head Room

Priming one coat with approved Water Bound Wall cement Primer on Plastered Surface of approved make including all cost etc. complete and as directed by the Engineer-in-charge.

Ground Floor

Head Room

Distempering two coats with any approved shade of distemper including all cost of materials etc. complete and as directed by the Engineer-in-charge.

Ground Floor

Head Room

Supplying and applying weather coat on outside walls two coats with any approved shade of weather coat including all cost etc. complete and as directed by the Engineer-in-charge.

Ground Floor

Head Room

PCC(1:2:4) using 12mm size hg chips including all cost of materials, labours etc. complete and as directed by the Engineer-in-charge.

Plinth protection

Supplying, fitting and fixing of stainless steel of 304 grade in hand railing using 50mm dia of 2mm thick circular pipe with Balustrade of size 32mm x 32mm x 2mm @ 0.90Mtr C/C and stainless square pipe bracing of size 32mm x 32mm x 2mm in 3 rows in stair case as per approved design and specification, buffing, polishing etc. with cost, conveyance, taxes, cess of all materials, cost of labour, T&P articles required for the work etc. complete as per specification and direction of the Engineer-in-charge.

Ground Floor

Providing and fixing rain water down pipe with necessary bend shoes and heads including cost of 75 mm dia earthen pipe,clamps, and nails etc. with all cost ,conveying taxes of all the materials required for the work with all labour, T&P and cess etc. completed in all respect as per specification and direction of the Engineer-in-charge

Ground Floor

Head Room

Construction of embankment with approved material obtained from borrow pits with all lift and leads transporting to site by mechanical means within a lead of 5kms spereading grading to required slope and compacting to meet requirement of table 300-2 & Clause 305 of MoSRT&H Specifications for Road & Bridge works (4th revision) etc. completed in all respect as per specification and direction of the Engineer-in-charge

Boundary wall

Earthwork excavation in hard soil with all leads & lifts including rough dressing &levelling bed & depositing the excavated material away from the working site as directed by Engineer in charge.

Filling foundation & plinth With sand well watered and rammed etc complete as directed by the engineer-in-charge.

Providing cement concrete (1:3:6) with nominal size stone aggregates for CC works including all cost etc. complete as directed by the engineer-in-charge.

RCC work of M-20 grade with 20mm and down graded black hard granite (C.B) stone chip[s including hoisting and laying. as directed by the Engineer-in-charge.

Column/Footing/Base

Columns up Plingth beam bottom

Plinth Band

Column

RRHG stone masonry in CM(1:6) in foundation and plinth including all cost of materials etc. complete and as directed by the Engineer-in-charge.

Cutting, bending, binding of MS rods and tying the grills and placing in position including cost of steel and binding wire and as directed by the Engineer-in-charge.

CB Brick masonary in CM(1:6) including all cost of materials etc. complete and as directed by the engineer-in-charge.

12mm thick CP in CM(1:4) over wall top including all cost etc. complete and as directed by the Engineer-in-charge.

16mm thick CP in CM (1:6) including all cost of materials etc. complete and as directed by the Engineer-in-charge.

MS grill gate etc. including all cost etc. complete and as directed by the Engineer-in-charge.

Main Gate

Painting two coat to the new surface of iron work with one coat primer including all cost of paint primer etc. complete and as directed by the Engineer-in-charge.

Supplying and applying weather coat on outside walls two coats with any approved shade of weather coat including all cost etc. complete and as directed by the Engineer-in-charge.

EI WORKS

Recessed wiring to light point with 1.5 sq.mm FR PVC insulatedsingle core multistrand copper conductor of ISI marked with 20 mm dia non-metalic PVC flexible conduit with 5Amp, 250 V piano type modular switch ISI marked and ceiling rose ISI marked mounted on MS box having front Modular base & cover of suitable size , MS box with 1 sq.mm FR PVC insulated single core multistrand copper conductor as earth wire including all accesories and connection as per direction of Engineer in Charge. ( Make of wire Finolex/ L&T / Anchor / Havels /HPL/ V Guard )

-do- Group A

-do- Group B

-do- Group C

Recessed wiring to Fan Point in...

-do- Group B

-do- Group C

Recessed wiring to Call Bell Point in...

-do- Group C

Recessed wiring to Exhaust Fan Point in…..

-do- Group B

S/F of Angle holder replacing Ceilling Rose

S/F of 5A. Switch & 5A. Socket outlet of ISI marked on existing board (Modular type) (1.25.1+1.25.4)

S/F of extension board of 6 modular Metal box with modular base & cover in recess including providing and fixing of 2 nos of 3pin 5/6amp modular socket out let & 2 nos of 5/6 amp piano type modular switch, connection, painting etc as required.

S/F of Power point with 4 modular metal box with modular base & cover in recess including providing and fixing of 5 pin 15/16 amp. piano type Modular switch & Socket, connection, painting etc as required

S/F of Power point with 4 modular & 2 modular metal box with modular base & cover in recess including providing and fixing of 5 pin 15/16 amp. piano type Modular switch & Socket & Mini DP MCB, connection, painting etc as required for AC

S/F of 1 no of 5 pin 15/16 amp. Socket , 1 no of switch & 1 no of 15/16A top with modular mini MCB, in 6 modular box with cover with connection, painting etc as required for Inverter connection

S/F to 18 SWG Modular GI box of following sizes (normal sixe) in recess with suitable size of Modular Base & Cover in front including cutting the wall and making good the same in case of recessed conduit as required.

(a)2 Modular box with base & cover

(b)4 Modular box with base & cover

(c)6 Modular box with base & cover

(d)8 Modular box with base & cover

(e)12 Modular box with base & cover

Wiring for circuit/sub main alongwith earth wire with following sizes of PVC insulated single core multistrand copper conductor with ISI marked conforming to IS-694/1990 in 20 mm dia non metallic heacy duty flexible conduit 1.6 mm in recessed PVC conduit as required (make of wire-Finolex/L&T/Anchor/Havels/V-Guard).

Inverter wiring (1x1.5smm) Copper wire (1.19.1)

S/F of 5 to 32 Amp rating 240 Volt "B" series MCB for lighting and other loads in the existing MCB Distribution Board ISI marked complete with connection, testing and commissioning etc. as required single pole (2.6.1)

S/F of 'B/C/D' series DP MCB of 5 - 32A amp rating (As per direction of engineer in charge) 240Volt for lighting and other loads in the 2 Way double door MCB Distribution board ISI marked complete with connection, testing and commissioning etc. as required (2.6.2a)+(2.3.1b)

Supply, Installation testing & commissioning of Main Switches (IS13940 part 3/1993) of following coopacity on existing surface/wall mounting & complete with H.R.C fuse links, inter connections earthing etc as required as per direction of Engineer Incharge (Make-Seimens/HPL/Anchor/L&T /Havels/C&S/R. K.)

S/F of MCB 8 way Double door (2.3.6)

Supply, Installation testing & commissioning of Main Switches (IS13940 part 3/1993) of following coopacity on existing surface/wall mounting & complete with H.R.C fuse links, inter connections earthing etc as required as per direction of Engineer Incharge (Make-Seimens/HPL/Anchor/L&T /Havels/C&S/R. K.)

S/F of 63A ICDP main switch with MS box of 250mmx300mmx60mm deep ( (2.15A)+(1.24.16 )

Earthing with G.I. earthpipe 3 mtr long. including accessories and providing masonary with cover plate having locking arrangement and watering pipe etc. with charcoal and salt as required.(3.2)

Supply andlaying 6 SWG G.I. wire in recess for loop earthing as required (3.17)

Supply, Installation, Testing & Commissioning of exhaust fan upto 225 mm sweep in the exising opening, including making the hole to suit the size of the above fan making good the damaged complete, connection, etc as required. (1.43)

S/F of Call bell/Buzzer(Ding dong type) ISI marked suitable for DC/AC single phase 230 volts complete as required. (1.30)

S/F of computer board consisting of 3 nos of 5amp modular plug and modular switch & 1 no of Mini MCB complete with wiring on 12 modular M.S. box with modular cover.

S/F of 18-25Watt L.E.D Tube light fitting with all accessories and connections (Make:HPL-Neptune Havells-Elite LED Pride Plus/PAC/Crompton-RetroPLL

Supply of 1200mm A.C. Ceiling fan with all accessories and connections with out fan regulator (Make:Usha-Striker Millenium/Crompton-Jura /Anchor-XL/Havels-Velocity/Spark/Orient-Summer pride )

S/F step type fan regulator

S/F of fan hook 'S' type made of 16 mm MS rod for fixing in the Existing RCC Roof.

SITC of 900-1100VA inverter with 150-160 AH tubular battery (Exide/Luminus/Crompton/Vguard)

Supply & Fixing of 60 Watt single L.E.D street light fitting with LED & Electrinic driver including all accessories and connections (Make:Crompton/Phillips/HPL/Polycab/Havells)

S/F of electronic 12w Watt LED square with surface panekl rings

S/F of 6 sqmm twin core unbonded aluminium service connection wire with no.10 G.I. Guard wire to support the aluminium wire

PH WORKS

Labour for drilling a perfectly vertical bore hole of specified dia for a specified depth below ground level through consolidated and unconsolidated rock with down the hole hammer drilling rig or combination rig as required to suit the site condition as per the direction of the Engineer in charge including use of own rig with its accessories, tools and plant and consumables etc for lowering of 200mm/150mm dia G.I/P.V.C/M.S casing pipes for housing fitted with socket and with or without well screen as per the necessity for soft, medium, hard and boulder formation(G.I/P.V.C/M.S casing pipes if required to prevent collapse of overburden is to be provided by the contractor including lowering and withdrawing after completion of the tube well), 200mm dia to 400mm dia in overburden portion including packing of gravel supplied by the contractor for 400mm dia bore only

Drilling of 125 mm dia bore 0 to 30 mtr

Drilling of 125mm dia bore 30 to 90 mtr

Labour for lowering the following size of PVC casing pipes with or without slotted pipes as per necessity from ground level upto 300 mtrs depth and fitted and set up in perfectly vertical position including cutting and threading of blank pipes and slotted pipes and supplyinging and fixing of all jointing materials ,extra sockets and T&P etc. all complete and keeping the top of casing pipe threaded including plugging the tubewell to prevent entry of foreign materials

Lowering of 200mm dia PVC casing pipes 0 mtr to 30 mtrs

Cost of 125mm dia PVC schedule - 80 pipe

Labour for drilling a perfectly vertical bore hole of specified dia for a specified depth below ground level through consolidated and unconsolidated rock with down the hole hammer drilling rig or combination rig as required to suit the site condition as per the direction of the Engineer in charge including use of own rig with its accessories, tools and plant and consumables etc for lowering of 200mm/150mm dia G.I/P.V.C/M.S casing pipes for housing fitted with socket and with or without well screen as per the necessity for soft, medium, hard and boulder formation(G.I/P.V.C/M.S casing pipes if required to prevent collapse of overburden is to be provided by the contractor including lowering and withdrawing after completion of the tube well), 200mm dia to 400mm dia in overburden portion including packing of gravel supplied by the contractor for 400mm dia bore only

Drilling of 125 mm dia bore 0 to 30 mtr

Drilling of 125mm dia bore 31 to 90 mtr

Labour for lowering the following size of PVC casing pipes with or without slotted pipes as per necessity from ground level upto 300 mtrs depth and fitted and set up in perfectly vertical position including cutting and threading of blank pipes and slotted pipes and supplyinging and fixing of all jointing materials ,extra sockets and T&P etc. all complete and keeping the top of casing pipe threaded including plugging the tubewell to prevent entry of foreign materials

Lowering of 200mm dia PVC casing pipes 0 mtr to 30 mtrs

Cost of 125mm dia PVC schedule - 80 pipe

Cleaning and developing the tube well with supply of compressor worked till clear and adequate discharge is obtained from the tube well including supply and use of all necessary equipment and labour as per direction of the Enginee

r in charge

Supplying and fitting & fixing of I.S.I make 1.00 H.P single phase Submersible Pump set to give discharge of 3000 ltr/hour at a head of 40 mtr etc all complete as direction of EIC.

Supplying and fitting & fixing of D.O.L starter for 1.0 H.P single phase Submersible Pump etc all complete as per direction of E.I.C

Supplying and fitting & fixing of suitable cable and connecting the pump and starter etc all complete as per direction of E.I.C

Supplying and fitting & fixing of Plastic rope, M.S well cover, M.S clamp, etc all complete as per direction of Engineer-in-charge.

Supplying and fitting & fixing of HDPE pipes and pipe fittings with C.P Nippling and lowering to bore well, making connection to pumpset & testing etc all complete as per specification and the direction of the E.I.C. 32 mm dia HDPE Pipe

Supplying all materials, labour, T&P and Fitting and Fixing of Rotational moulded polythene cylindrical vertical water storage tank conforming to 15701/1996 including cutting holes through the tank and fixing mild steel tubes and fittings and providing extra sockets and jamnuts, including hoisting upto a height of 5 mtr above G.Land placing the tank in required position including conveyance of all materials to work site, payment of royalty, taxes etc all complete as per P.H specification and direction of the E.I.C. 2000 lits capacity on the roof of GF

Supplying all materials, labour, T&P and construction of masonry staging with providing 1st class K.B. Brick work in C.M.(1:6) of 0.46mtr height in staging, 12 mm cement plaster in C.M (1:6), R.C.C. Beam of 0.25mx0.30mx2.60m & roof slab of 1.40mx1.40m in C.C (1:1.5:3) using 12mm size H.G.Chips including centering, shuttering, bending and binding of rod etc watering, curring, conveyance of all materials to work site, payment of royalty, taxes etc all complete as per P.H specification and direction of the E.I.C. 2000 lits capacity on the roof of GF

Earthwork in all kinds of soil in excavation of foundation trenches within 50m initial lead and 1.5m initial lift including rough dressing and breaking clods to maximum 5cm to 7cm and laying in layers not exceeding 0.30m in depth etc all complete as per direction of the E.I.C.

Initial lift upto 1.5 mtr

4.36 m x 3.17 m x 1.50 m=20.731 cum

From 1.5 mtr to 3.0 mtr depth

4.36 m x 3.17 m x 0.70 m=9.674 cum

Supplying all materials, labour, T&P and filling in foundation and plinth with river sand well watered and rammed including conveyance of all materials to work site, payment of royalty, taxes etc all complete as per the direction of the E.I.C.

4.36 m x 3.17 m x 0.15 m=2.073 cum

Supplying all materials, labour, T&P and filling in foundation and plinth with river sand well watered and rammed including conveyance of all materials to work site, payment of royalty, taxes etc all complete as per the direction of the E.I.C.

Supplying all materials, labour, T&P and providing cement concrete (1:3:6) with 40mm H.G metal including watering, curing and conveyance of all materials to site payment of royalty, taxes etc all complete as per P.H specification and direction of the E.I.C.

Supplying all materials, labour, T&P and providing plain cement concrete (1:1.5:3) with 12mm size H.G chips including watering, curing and conveyance of all materials to work site, payment of royalty, taxes etc all complete as per P.H specification and direction of the E.I.C.

4.36 m x 3.17 m x 0.10 m=1.382 cum

3.12 m x 1.93 m x 0.038 m = 0.228 Cum

Supplying all materials, labour, T&P and providing brick work with Fly Ash Bricks (23 cm x 11 cm x 8 cm) having crushing strength not less than 75kg/cm² with dimensional tolerance ± 8 percent in cement mortar (1:4) including watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the E.I.C

In Foundation and Plinth in C:M (1:4)

2 x ( 4.06 + 1.93 ) m x 0.47 m x 1.10 m = 6.193 cum

2 x ( 3.82 + 1.93 ) m x 0.35 m x 0.80 m = 3.220 cum

In Foundation and Plinth in C:M (1:6)

1 x 0.40 m x 0.40 m x 0.60 m = 0.096 cum

Supplying all materials, labour, T&P and providing cement plaster on brick/stone work including watering,curring and conveyance of all materials to work site, payment of royalty, taxes etc all complete as per P.H specification and direction of the E.I.C.

12 mm thick C.P in C:M (1:3)

2 x ( 3.12 + 1.93 ) m x 1.90 m =19.19 sqm

3.12 x 1.93 m = 6.021 sqm

4 x 0.40 x 0.60 m = 0.96 sqm

Supplying all materials, labour, T&P and providing cement punning on plastered surface including watering,curring and conveyance of all materials to work site, payment of royalty, taxes etc all complete as per P.H specification and direction of the E.I.C.

Same as above item 20mm C.P in 1:3

Supplying all materials, labour, T&P and providing rigid and smooth centering and shuttering for RCC work including false work and dismantling them after casting including conveyance of all materials to work site, payment of royalty, taxes etc all complete as per P.H specification and direction of the Engineer-in-charge.

2 x ( 3.12 + 1.93 ) m x 1.90 m =19.19 sqm

2 x (3.82 + 2.63 ) m x 0.125 m =1.612 sqm

Supplying all materials, labour, T&P and providing M.S.reinforcements for RCC work including cutting, bending, binding, straightening and tying the grills and placing in position including cost of binding wire 18 to 20 gauge conveyance of all materials to work site, payment of royalty, taxes etc all complete as per P.H specification and direction of the Engineer-in-charge.

Supplying all materials, labour, T&P and providing Reinforced cement concrete (1:1.5:3) with 12mm size H.G chips including watering, curing and conveyance of all materials to work site, payment of royalty, taxes etc all complete as per P.H specification and direction of the E.I.C.

3.82 m x 2.63 m x 0.125 m

Supplying all materials, labour, T&P and making M.S. Step Iron in 20mm Dia M.S Steel bars and fixing into walls of Manhole/ Septic Tanks duly embeded in C.C(1:2:4) etc all complete as per P.H specification and direction of the E.I.C.

Supplying all materials, labour, T&P and providing 50mm thick pre-cast R.C.C. baffle wall in R.C.C(1:1.5:3) including reinforcement cage using 12mm size HG chips fitted and fixed in position, finished smooth etc. complete including cutting grooves and mending good the damages etc all complete as per P.H specification and direction of the E.I.C.

Supplying all materials, labour, T&P and providing 160mm dia P.V.C Tee inside the septic tank including cutting holes and duly embeded in P.C.C(1:1.5:3) using 12mm size HG chips fitted and fixed in position and mending good the damages etc all complete as per P.H specification and direction of the E.I.C.

Supplying all materials, labour,T&P and providing 12mm thick cement flush pointing in C:M (1:3) to Brick Masonry works including watering curring and conveyance of all materials to work site, payment of royalty, taxes etc all complete as per P.H specification and direction of the Engineer-in-charge.

2 x ( 4.06 + 2.87 ) m x 1.10 m = 15.246 Sqm

2 x ( 3.82 + 2.63 ) m x 0.80 m = 10.32 Sqm

2 x ( 4.06 + 2.63 ) m x 0.125 m = 1.672 Sqm

Supplying all materials, labour,T&P and filling Foundation and Plinth with excavated earth including watering, ramming etc all complete as per direction of the E.I.C.

Supplying all materials, labour, T&P and constructing Inspection Chamber of the following sizes with cement concrete (1:3:6) using 40 mm size HG metal on bed, 1st class KB Brick work in CM (1:6) moulding and shaping the channel inside and benching with C:C (1:1.5:3) using 12 mm size H.G chips, 12 mm thick cement plaster (1:3) with punning to inside, cement flush pointing (1:3) to outside, RCC cover slab in C.C(1:1.5:3) using 12 mm size H.G chips with RCC man hole cover, etc. all complete as per approved specification and direction of E.I.C Inside size 760mm x 760mm x 460mm

Supplying all materials, labour, T&P and constructing Gully Trap chamber of the following inside size with 8 cm thick precast cover slab in CC (1:2:4) mix using 12 mm size H.G chips, foundation concrete (1:4:8) using 40 mm size HG metal on bed and around trap , !st class KB Brick work in CM (1:6) in F & P and inside 12 mm thick cement plaster (1:3) finished with a floating coat of neat cemen

t including fixing 100mmx100mm size HCI gully trap 150mmx150mm size C.I grating etc. all completed as per approved drawing, specification and direction of E.I.C.

Supplying all materials, labour, T&P and constructing soakway pit of the following size with dry brick walling from bottom upto invert of inlet pipe and 1st class KB brick work in CM (1:6) for the remaining height at top, 12mm thick Cement Plaster (1:4) inside and outside over masonry brick work, gravel packing in the rear of well steining, RCC cover slab in CC (1:1.5:3) using 12mm HG chips, fitted with iron lifting handles. etc all complete as per approved specification and direction of the E.I.C. 1.00 m diax 2.0 m deep soakway pit

1.20 m diax 2.0 m deep soakway pit

Supplying all materials, labour, T&P and laying in trenches U-PVC SWR/4Kg/cm2 soil waste ventilating pipes and fittings of the following outside diameter conforming to ISI No 13592/1992 including jointing with supply of approved rubber lubricant by non-heat application method/as per manufacturer's specification, testing, earthwork in excavation in all kinds of soil and providing bed concrete in P:C:C (1:4:8) using 40 mm size metal and haunch top the pipe with refilling of trenches etc all complete as per P.H specification and direction of the E.I.C.

110mm Hunch Top

160mm PVc Pipe all round Hunch top

SanitaryInstalation/Supplying all materials, labour, T&P and fitting and fixing U-PVC SWR soil waste ventilating pipes and fittings of the following outside diameter conforming to ISI No 13592/1992 to walls with nails, bobbins and wooden plugs including jointing with supply of approved rubber lubricant by non-heat application method/as per manufacturer's specification, testing etc all complete as per P.H specification and direction of the E.I.C. 110mm diameter U-PVC SWR pipes

110mm U-PVC SWR P-trap

110mm U-PVC SWR Single junction door

110mm U-PVC SWR door bend

110mm U-PVC SWR Offset

110mm U-PVC SWR plain bend

110mm U-PVC SWR vent cowl

75 mm diameter U-PVC SWR pipes

75 mm U-PVC SWR plain bend

125 mm dia C.P Grating

Internal PH Works

Supplying all materials, labour, T&P and providing and fixing to wall or ceiling or floor G.I./PVC pipes and pipe fittings of the following nominal bore with clamps including making good the wall, ceiling,and floor, testing all complete as per specification and the direction of the E.I.C. 20mm dia C-PVC pipes Internal

25mm dia CPVC pipes External

supplying all materials, labour, T&P and cutting holes through existing brick/stone masonry walls for taking GI/PVC pipes and fittings including making good the damages in cement mortar (1:4) etc. all complete as per P.H. specification and direction of E.I.C. R.C.C Roof/Chaja

Cutting Groove in wall or floor

Cutting hole(250 mm wall)

Ground Floor

Cutting hole(375 mm wall)

Supplying all materials, labour, T&P and fixing porcelain glazed tiles in floors, on 25mm thick bed of cement mortar 1:1 joined with neat cement slurry mixed with pigment to match the shades of the tiles including rubbing and polishing etc. all complete as per specification and direction of the E.I.C.

4nosx1.50x2.10m=12.60 Sqm

Kitchen

Ground Floor

2nos x 3.0x0.60=3.60

Supplying all materials, labour, T&P and fixing porcelain glazed tiles in dados/skirtings on 12mm thick cement plaster (1:3) joined with neat cement slurry mixed with pigments to match the shades of the tiles including rubbing and polishing etc. all complete as per direction of the E.I.C.

4nos 7.20mx2.100=60.48 Sqm

2nos x 3.0mx0.9m=5.40 Sqm

Supplying all materials, labour, T&P and fixing Eoropian Watter closet and seat cover with 'P' trap plain etc all complete as per specification and direction of the E.I.C. ( EWC With Seat Cover) of Make Cera/Hindweare/Parryware.

Supplying all materials, labour T&P and fitting and fixing 10 Ltrs capacity PVC low level flushing cistern with a pair of C.I. or M.S.brackets complete with fittings such as syphonic arrangement, 15mm nominal size Brass/PVC ball valve with polythene float, CP/Brass handle, unions and couplings for connection with inlet, outlet, overflow pipes, 32mm dia PVC flush bend, 15mm dia PVC connection pipes including cutting holes and making good the same and connecting the flush bend with cistern and closet and connecting inlet pipe with supply main with etc all complete as per specification and direction of the E.I.C

Supplying all materials, labour T&P and fitting and fixing of C.P Shower(Parryware,Hindware) with 15mm or 20mm inlet with C.P Shower arm including polishing etc all complete as per specification and direction of the E.I.C 15 mm x 150mm dia C.P Shower with arm

15 mm dia C.P hand Shower(Health Fucet), Jaquar Make

Supplying all materials, labour T&P and fixing wash basins(Hindware,Parryware) with C.I. or M.S.brackets painted white including cutting holes in walls and making good the damages with supply of wooden plugs, screws and cement etc, fixing PVC waste pipe of 32mm nominal diameter for wash basin including brass check nut complete, fixing 32mm dia CP brass waste, etc all complete as per specification and direction of the E.I.C. 550mmx400mm size wash hand basin

Pedestal for Wash Basin

600x450x200 mm stainless steel kitchen sink (Mousumi make)

Supplying all materials, labour, T&P and fixing mirror of superior glass mounted on 6mm thick A.C.sheet or plywood sheet and fixed to wooden plugs with CP screws and washers complete as per specification and direction of the E.I.C.

Glass shelf with C.P. bracket with guard rails

Supplying all materials,labour, T&P and fixing standard sized CP towel rail complete with CP brass brackets fixed to wooden plugs with CP screws as per specification and direction of the E.I.C 20mmx450mm long CP towel rail

Supplying all materials, labour, T&P and fixing CP soap holder complete with CP brass brackets fixed to wooden plugs with CP screws as per specification and direction of the E.I.C

CP Towel Ring

CP Liquid Soap Container

CP Paper Holder

Supplying all materials, labour, T&P and fitting and fixing Brass/CP fittings(Jaquar Make) of the following nominal bore with supply of all jointing materials etc. all complete as per specification and the direction of the E.I.C. 15mm dia CP Bib Cock SB

15mm dia CP Bib Cock LB

15mm dia CP Pillar Cock

15mm dia 2 in 1 way Bib Cock

15mm dia CP Angle Stop Cock

15mm Wall Mixture ( 3in One)

15mm dia CP Concealed Stop Cock

25mm dia Brass Full Way Valve

15mm dia CP telephonic shower with PVC flexibel tube & hook

Factory made FRP(alternately called GRP) door frame of size 75mmx100mm fabricated using E-glass Chopped Strand Mat (CSM) U.V stabilised Inopthalic Gelcoat and impregnated with Inopthalic resin. The thickness of the GRP skins shall not be less than 2.00mm. The door frame consist of four segments which are provided with plug-in-socket arrangement in-situ in the mould. The segments are plugged in and are joined together by means of screw. The GRP frame shall be provided with wooden reinforcement on six locations for high screw holding capacity for for fixing metallic hold fast and shall be consolidated by filling with medium density foam/plaster of paris with fibre reinforcement, Six numbers of 260mm x 25mm x 5mm size 'S' shaped M.S flat hold fast shall be provided with the frame. The material and process for manufacturing the door frames shall conform to RV-TIFAC composites Design Centre's standards and specifications. The finish of door frame will be plain colour white/ Ivory/ Beige/ Light grey/ Golden brown/Mahogany/ Teak wood/sand stone/Champagne/Pastel blue or any other colour using high quality pigments complete in all respect as per specification and direction of the E.I.C