ADDITION ALTERATION RENOVATION WORKS IN MANDAKINI BLDG BLDG No 105 SABARMATI BLDG BLDG No 227 AT DLRL UNDER GE I RND KANCHANBAGH HYDERABAD

Amount

Taking down existing roof treatment of any description, any position with bituminous felt including plaster / loose concrete and removing rubbish to a distance exceeding 500m but not exceeding 1000m complete all as specified and directed.

M&L for Plain Cement Concrete type B1, 1:2:4 (using 20 mm graded stone aggregate) as in padding concrete, coving of vertical junctions on roof top, complete all as specified and directed by Engineer-in-Charge.

M&L for brushing neat cement slurry with 3 Kg of cement per Sqm over the RCC slab and sides complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 10mm in CM 1:3 over concrete surfaces on RCC roof slab and parapets mixed with WPC @ 3% by weight of cement shall be carried out complete all as specified and directed by Engineer-in-Charge. Note: WPC will be measured under separate item of this schedule.

Supply only, integral water proofing compound complete all as specified and directed. Make: SCOTT / AQUA PROF / RAILIA.

M&L for water proofing treatment with polymeric standard membrane of weight not less than 3kg per Sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt not less than 150gms/sqm) laid over primed surface by forced application complete. Shall be fused uniformly by LPG torch flame on horizontal / vertical / slope surface on roof complete and preparation of surfaces of any description, over 10cm in width or girth otherwise described and appplying two coat of aluminium paint @100ml per Sqm over APP membrane sheet complete all as specified and directed by Engineer-in-Charge. Water proof treatment consist of as under: - (i) Applying one coat of bitumous primer conforming to IS 3384 @ 0.3 ltrs per sqm. (ii) Laying APP based memberane as specified thickness and weight. (iii) Appplying one coat of bitumen grade 85/25 @1.20Kg per Sqm. (iv) Two coats of aluminium paint.

Demolition of plain cement concrete (unreinforced) in ground floors and paving n exc 15cm thickness below or above ground level, removal of rubbish and debris and depositing in low lying areas out side MOD land complete all as specified and directed.

M&L for cutting grooves in brick wall 70mm wide and 65mm deep and sweeping horizontal face of groove with cement mortar (1:3) and making good in CM 1:3 after inserting membran into the groove complete all as specified and directed by Engineer-in-Charge.

M&L for specialised poly sulphide sealant treatment to the tarrece / wall cracks as under :- (a) Cleaning of surface (b) Making V grooves (6mm width and depth) (c) Application of primer one coat (zoriseal primer / arbokol AG2 primer / assar power primer). (d) Filling of groove with two coats of polysulphide sealant.

Taking down chowkats or frame with shutters (without taking off shutters from frame) but each not exceeding 1.50 Sqm complete all as specified and directed.

Taking down chowkats or frames with shutters exceeding 1.5 Sq. M but not exceeding 4 Sq. M each (Without taking off shutters from the frame) complete all as specified and directed.

S&F, factory made solid PVC door frame of size 50 mm x 47 mm made out of 5mm wood grain printed PVC sheet reinforced with MS square tube manufactured as per SSR Part I specifications and drawing complete all as specified and directed.

S&F, factory made solid PVC moulded door shutter 28 to 30 mm thick (style) with 2, 4 or 6 raised panel design with 2mm thick mouded PVC sheet on front face & 2mm plain colour PVC sheet on back face with wood free EPS Core all as per specification complete all as specified and directed.

S&F, mild steel butt hinges, medium weight cold rolled 100 mm size complete all as specified and directed.

S&F, 200 mm long aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F, 150 mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

Demolition of un-reinforced cement concrete in ground floors incl tiles and pavings not exceeding 15 cm thickness, (Below or above ground level) and disposal of unserviceable materials, debris and rubbish to a distance outside MOD land as directed by the Engineer in Charge.

M&L for Cement concrete type D2, 1:4:8 (using 40 mm graded stone aggregate) in mass concrete of sub base of flooring / hard standing complete all as specified and directed.

M&L for Machine pressed precast concrete interlocking paver block with grey cement and pigments any shape and size confirming to IS 15658 - 2006 of 60 mm thickness, M-35 Grade with grey cement and pigment over 50mm thick sand cushioning complete all as specified and directed.

M&L for non skid coloured ceramic tiles 9 to 10 mm thick (square / rectangular) joint free area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc over and including 15 mm thick screed bed in CM 1:4 over 30 mm thick PCC (1:2:4) type B-0 jointed and pointed in white or coloured cement to match with the colour of tiles complete all as specified and directed.

All as per Sl item No. 20 above, but as in skirting over 10 mm thick screed bed in CM 1:4 and jointed and pointed in white or coloured cement to match with the colour of tiles complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc., including removal of rubbish off the premises complete all as specified and directed.

Rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 and finished even and smooth without using extra cement including mixing of water proofing compound wherever required complete all as specified and directed.

Rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 and finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparing newly plastered surfaces and applying two coats of distemper oil emulsion including priming plastered and other surfaces with alkali resistant priming paint on surfaces of walls over a coat of wall putty to make surfaces smooth complete all as specified and directed.

M&L for complete removal of existing treatment and applying two coats of distemper oil emulsion including priming plastered and other surfaces with alkali resistant priming paint on surfaces of walls over a coat of wall care putty to make surfaces smooth complete all as specified and directed.

M&L for preparation of new plastered surfaces and applying two coats of weather proof antifungal acrylic exterior emulsion paint of apex ultima and shade as approved over a coat of approved primer as recommended by the manufacturer over a coat of water proof birla putty to make surfaces smooth all as required and as directed.

M&L for complete removal of existing treatment and applying two coats of weather proof acrylic exterior emulsion paint of apex ultima and shade as approved over a coat of approved primer as recommended by the manufacturer over a coat of water proof birla putty to make surfaces smooth all as required and as directed.

Cutting / chipping the spalling concrete surfaces of columns, beams, slabs, cantilevers etc., and trimming, cleaning the surface to receive guniting / plastering complete all as specified and directed.

M&L for preparing old concrete surfaces and applying a coat of NITO Bond EP of M/s Fosroc Chemicals or equivalent approved bonding agent as per manufacturer's instructions complete all as required and as directed.

M&L for providing pressure guniting averaging 20 mm thick in cement mortar 1:3 for soffits of slab, chajjas, parapets, etc., complete all as specified and directed including providing double scaffolding as required and removal of the same on completion of the work complete all as required and directed.

Rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 and finished even and smooth without using extra cement including mixing of water proofing compound wherever required complete all as specified and directed.

M&L for preparing newly plastered surfaces of ceilings and applying three coats of white wash complete all as specified and directed.

M&L for preparing old surfaces of ceilings by brooming down or by steel wire brushing and applying one coat of white wash complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to stores and rubbish off the premises complete all as specified and directed.

M&L for Non-skid coloured ceramic tiles 7 to 8mm thick area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tile including 15mm thick screed bed cement motar 1:6 complete all as specified and directed.

S&F, Glazed coloured ceramic tiles in vertical surface 450 x 300 x 7 mm thick, set and jointed in neat cement slurry and pointed in white or cloured cement 10mm thick rendering in CM 1:4 complete all as specified and directed.

S&F in repairs vitreous china wash hand basin white, oval shape of size 510 mm x 450 mm counter top of approved make and model including taking down the existing WHB fitting complete all as required at site and as directed.

S&F in repairs vitreous china wash down water closet (Pedestal), white (ETWC) and 10 litres PVC capacity valve less, Syphonic action type, flushing cistern, low level, white with inlet, ball valve, float and handle including brackets (SLIM LINE or equivalent) including PVC Flush pipe 32 mm dia, plastic seat of same colour of WC, closed pattern with flat bottom, and cover and mild steel chromium plated hinging device complete including taking down the existing EWC fitting complete all as specified and directed.

S&F in repairs vitreous china urinal, half stall type of size 46 x 30 x 71 cm, white complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement complete all as specified and directed. Make: Cat Part No. 96010 of Hindware or equivalent in Perryware.

S&F in repairs brass chromium plated urinal spreader heavy duty suitable for half stall urinal fixed in position complete all as specified and directed.

S&F in repair CP connections for 15mm bore dia with CP brass nuts and rubber washer of length 450mm fixed for urinals complete all as specified and directed.

S&F, vitreous china urinal partition white of size 310 x 770mm complete all as specified and directed.

S&F, waste coupling suitable for wash baisn, urinal, sink etc., of PTMT (Half or full threaded) of minimum weight 45 grams, and fixed to discharge pipe of 32 mm dia., bore complete all as specified and directed.

S&F in repairs brass chromium plated tubular towel rail, 20 mm dia, 'D' type, 60cm long between flanges complete all as specified and directed.

S&F in repairs 15 mm bore fancy type chromium plated bib taps two way, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule including taking down the existing fitting complete all as specified and directed.

S&F in repairs fancy type chromium plated 15 mm bore angle valves, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions including taking down the existing fitting complete all as specified and directed.

S&F in repairs fancy type chromium plated 15 mm bore push type stop valves, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions including taking down the existing fitting complete all as specified and directed.

S&F in repairs 15 mm bore fancy type pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete all as specified and directed.

S&F, Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

Taking up or down 15 mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed.

Taking up or down 20 mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed.

S&F, 15 mm bore galvanized steel tubes, medium grade for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors complete all as specified and directed.

S&F, 20 mm bore galvanized steel tubes, medium grade for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floor complete all as specified and directed.

Taking down eaves gutters and rain water pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed.

S&F, PVC (SWR) pipes, 150 bore of pipe, single socketed, in any length with rubber ring joints, fixed in position with walls including enlarging existing hole in slab, beam or parapet etc and making good with cement mortar 1:4 complete all as specified and directed.

S&F, 150mm PVC (SWR) bends any radius complete all as specified and directed.

Dismantling of cast iron soil or waste pipes of 100 mma dia, jointed in cement mortar and taking out of trenches, if required complete all as specified and directed.

Dismantling of cast iron soil or waste pipes of 75 mma dia, jointed in cement mortar and taking out of trenches, if required complete all as specified and directed.

M&L for PVC (SWR) plain floor trap of 75 mm dia, outlet with grating including jointing with solvent cement complete all as specified and directed.

S&F, 75 mm bore PVC (SWR) soil, waste and vent pipes single socketed in any length with rubber ring joints laid in floors or trenches complete all as specified and directed.

S&F, 110 mm bore PVC (SWR) soil, waste and vent pipes single socketed in any length with rubber ring joints laid in floors or trenches complete all as specified and directed.

S&F, 75 mm bore PVC (SWR) soil, waste and vent pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F, 110 mm bore PVC (SWR) soil, rain water, waste and vent pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F, 75 mm bore PVC (SWR) junction single (Single `T') equal or unequal with access door complete all as specified and directed.

S&F, 110 mm bore PVC (SWR) junction single (Single `T') equal or unequal with access door complete all as specified and directed.

S&F, 110 mm bore PVC (SWR) vent cowl complete all as specified and directed.

S&F, 75 mm bore PVC (SWR) bends of any radius complete all as specified and directed.

S&F 75 mm bore PVC (SWR) bends of any radius with oval access door complete all as specified and directed.

S&F 110 mm bore PVC (SWR) bends of any radius complete all as specified and directed.

S&F salt-glazed stoneware gully traps, square or round mouthed, tvpe 'P' size of trap 150 x 150 mm complete all as specified and directed.

S&F 750 mm long, 32/40 mm dia, PVC flexible waste pipe for sinks / wash hand basins / urinals complete all as specified and directed.

Precast cement concrete 1:2:4, type B1, (using 20mm graded stone aggregate) in landings, cover slabs (for manholes etc.) shelves and similar articles with plain faces and set in cement mortar 1:6, complete all as specified and directed.

Mild steel TMT bars 6 mm to 8 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia, or securing with clips complete all as specified and directed.

S&F, 1000 litres capacity rotational moulded polyethylene water storage tanks white (cylindrical vertical with threaded lid) hoisted and fixed in position all as specified in SSR Part I including taking down old water tanks complete all as specified and directed.

S&F in repairs, 25 mm dia, ball brass valves, high pressure, with polythene float and fly nut complete, screwed for Iron pipe or brass ferrule complete all as specified and directed.

S&F in repairs, 25 mm dia, gun metal, globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed in repairs including taking down the existing fitting complete all as specified and directed.

M&L for MS framed work such as grills, gratings etc, with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290, Gde-E-165de E-165 complete all as specified and directed.

M&L for prepration of new steel surface of any description not other wise described over 10 cm width or girth and applying two coat of synthetic enamel paint over one coat of red oxide complete all as specified and directed.

M&L for powder coated aluminium (minimum thickness of powder coating 50 micron) work for partitions (fixed portions) with extruded built up standard tubular sections / appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber / neoprene gasket etc., aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, CP brass / stainless steel screws and complete as per architectural drawings and the directions of Engineer-in-Charge including taking down old partition complete all as specified and directed.

Dismantling ceiling boards (fibre, pulp, insulation, etc) or insulation boards / slabs / blankets, any thickness, including cover fillets and frame complete all as specified and directed.

S&F, Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre / intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre and hangers 6 mm dia, GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of GI flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long complete all as specified and directed.

Providing and fixing Gypsum Board 12mm thick in ceiling fixed with screw as per manufacturers instructions and finished with two coats of plastic emulsion paint over a coat of primer on exposed surfaces complete all as specified and directed.

S&F, anodised aluminium window and ventilator shutters, sliding type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, guide channel two track, anodised aluminium fittings such locking arrangement complete all as specified and directed.

S&F, powder coated glazed aluminium door shutter and chowkats, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door 'D' type 450 mm long, one powder coated alum tower bolt of 250 mm length and one 300 mm long sliding bolt for each leaf, powder coated aluminum snap beading screws etc, mounted on floor spring and glazed with 5 mm thick plain sheet glass or 12 mm thick PLPB fixed with rubber beading / gasket and powder coated aluminiun beading and one mortice lock complete incl taking down old door complete all as specified and directed.

S&F, powder coated aluminium grill of approved design / pattern with approved standard section and fixed to the existing window frame with CP brass / stainless steel screws @ 200 mm centre to centre, including cutting the grill for making provision of opening / closing of window and fixing with approved powder coated aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-Charge.

S&F, Solar control film 25 micron reflective type sticked to glass panes of windows as per instructions of manufacturers, properly rolled on glass panes without any wrinkle complete all as specified and directed.

S&F, 4.8 mm thick sheet glass, ordinary quality and glazing with oil putty or beading in square exc 0.5 sq. m in each pane complete all as specified and directed.

S&F, 12mm thick prelaminated particle board, exterior grade, prelaminated both sides with decorative choice lamination, fixed with beading complete all as specified and directed.

S&F, venetian blinds roller type multicolour fibre water resistant, UV protection, transparent, black outside suitable for windows etc fixed and including taking down existing unserviceable one, complete all as specified and directed.

S&F, stainless steel grade 304 railing 68mm dia hand rail and 3 Nos, 16mm dia horizontal rails and 40mm dia balusters fixed at 900 mm centre to centre with clamps and dash fastener including newel post of 75 mm dia with spherical cap fixed at starting and terminal point of railing incl taking down old stair case railing of any description complete all as specified and directed.

S&F, UPVC windows or UPVC framed portion 3 track sliding window with two glazed and one wire mesh sliding shutters of profile width of frame 50mm to 60mm, limit thermal conductivity to 1.3 Kcal/sqm/hr centigrade, sound insulation upto 4-0 bds, density, 1.46 gm/ml, tenstile strength-43.9N/sqmm, % elongation at break-215, tenstile mpduls-2840N/sqmm, flexural strength-51N/sqmm, heat aging at 150 degrees-No surface defect, thickness-2mm, flexural moduls elasticity 2200N / sqmm, double baskets & wool pile on window, multi point gear locking at different sides of frame, anti lift device on slide windows with temper proof screws with and including glazed shutter fixed with 5mm thick tinted sheet glass & wire mesh shutter with stainless steel wire cloth 304 grade stainless steel with 0.254mm (30 gauge) dia of steel wire and 0.95mm width of aperature complete including taking down old down old window complete all as specified and directed.

S&F, UPVC ventilators with top hung shutters made out of profile width of frame 50mm to 60mm, limit thermal conductivity to 1.3 Kcal/sqm/hr centigrade, sound insulation upto 4-0 bds, density, 1.46 gm/ml, tenstile strength-43.9N/sqmm, % elongation at break-215, tenstile mpduls-2840N/sqmm, flexural strength-51N/sqmm, heat aging at 150 degrees-No surface defect, thickness-2mm, flexural moduls elasticity 2200N / sqmm, double baskets & wool pile on window, multi point gear locking at different sides of frame, with peg stay of suitable size to keep hung shutter in open position, with temper proof screws with and including glazed shutter fixed with 5mm frosted sheet glass complete all as directed including taking down old down old vents complete all as specified.

M&L for 20 mm thick, granite work (table rubbed and polished) lakha red in steps, jambs, pillars, window cills, cooking platforms, landings of staircases and like in cement mortar 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigments to match with the shade of granite and polishing the exposed edges as required complete all as specified and directed.

M&L for 20 mm thick, granite work (table rubbed and polished) lakha red for wall cladding laid over 12mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite as required complete all as specified and directed.

Taking down carefully of any type point wiring light fans socket or power complete fitting such as switch ceiling roses, pendent, regulator, sockets etc removing material and making good disturbed surface of wall floor etc complete all as specified and directed.

M&L for point wiring 1.5 sqmm single core PVC insulated but unsheathed multistranded copper conductor FRLS cable 1100 Volts grade drawn through and including non metallic rigid PVC medium grade concealed conduit including conduit accessories like bends, tees, junction boxes etc fixed concealed in wall or ceiling etc including 1.5 sqmm PVC insulated unsheathed multistranded copper conductor FRLS cable as earth continuity wire including modular type, metal flush box with cover plate and frame of required module for mounting of modular switches, sockets, switch sockets, fan regulators with required modules etc for:- One light point controlled by one 5 Amps one way modular switch.

All as per Sl item No. 98, but for one ceiling fan / exhaust fan point controlled by one 6 Amps one way modular switch.

All as per Sl item No. 98, but for one 3 pin socket outlet 6 Amps on the same board with other modular switches.

All as per Sl item No. 98, but for one 3 pin 6 Amps modular switch socket outlet point on independent board.

All as per item No. 98 here in before, but for 15 Amps socket outlet with 2.5 Sqmm copper including 2.5 Sqmm PVC insulated copper conductor cable as earth continuity conductor and connecting to common earth dolly.

S&F, modular type 06 Amps, 05 pin mulitipurpose switch, socket outlet 03 Nos and 16 Amps multipurpose switch, socket outlet 01 Nos on one switch board concealed in wall suitable for terminal boxes for fixing of switch sockets etc including suitable size modular plates and including all internal electrical connections with copper conductor complete all as specified and directed.

S&F, modular type 06 Amps, 05 pin mulitipurpose switch, socket outlet 04 Nos on one switch board concealed in wall suitable for terminal boxes for fixing of switch sockets etc including suitable size modular plates and including all internal electrical connections with copper conductor complete all as specified and directed.

S&F, Modular Switch 1 way, 6 Amps, 230 volts 1 Module complete all as specified and directed.

S&F, modular switch 1 way, 16 Amps, 230 volts 1 module complete all as specified and directed.

S&F, Modular sockets, 6 Amps, 230 volts, 2/3 pin, combined 2 module complete all as specified and directed.

S&F, Modular sockets, 16 Amps, 230 volts, 5 pin, combined 2 module complete all as specified and directed.

S&F, Modular fan regulator, 120 watts, 230 volts, 2 module complete all as specified and directed.

S&F, Sheet Metal enclousure Plug and socket type 20 Amps capacity with of single pole 20 Amps MCB 'C' curve 230 Volts, 50 Hz, plug top and earth plug, grouted flush to walls complete all as specified and directed.

S&F, Sheet Metal enclousure Plug and socket type 32 Amps capacity with provision of MCB TPN 32, 415V plug top and earth plug, grouted flush to walls complete all as specified and directed.

S&F, MCCB 200 Amps, 25 KA 4-Pole type, including sheet metal enclosure suitanble for fixiing of MCCB and all arrnagement for mounting and testing, operating on 415V, 50Hz, AC supply, including taking down of old unserviceable one complete all as specified and directed.

S&F, MCCB 100 Amps, 16 KA, 4-Pole type, including sheet metal enclosure suitable for fixiing of MCCB and all arrnagement for mounting and testing, operating on 415V, 50Hz, AC supply, including taking down of old unserviceable one complete all as specified and directed.

S&F, MCCB 63 Amps, 16 KA, 4-Pole type, including sheet metal enclosure suitable for fixiing of MCCB and all arrnagement for mounting and testing, operating on 415V, 50Hz, AC supply, including taking down of old unserviceable one complete all as specified and directed.

S&F, MCB TPN 100 Amps, 415 volts, 16KA rupturing capacity complete all as specified.

S&F, MCB TPN 63 Amps, 415 volts, 16KA rupturing capacity complete all as specified and directed.

S&F, MCB TPN 40 Amps, 16KA rupturing capacity 415 volts complete all as specified and directed.

S&F, MCB SPN 5 to 40 Amps, 230 volts, 10KA rupturing capacity 'C' curve, complete all as specified and directed.

S&F, MCB SP 5 to 40 Amps, 10KA rupturing capacity 230 volts complete all as specified and directed.

M&L for MCB DB TPN sheet metal enclosure with category of protection double door type IP-43 protection factory made with tinned copper 200 Amps rated bus bar suitable for MCBs, triple pole and neutral, 415 volts, 4 way including taking out old one complete all as specified and directed.

Dismantling of existing unserviceable MCB distribution board and S&F, sheet metal enclosure DB flush with wall having facility to fix MCCB as incomer and MCBs in outgoing, TP vertical type 8 way of double door, IP 43 protection, complete fitted with bus bars, neutral links, G frame including S&F, 4 pole MCCB 125 Amps capacity, Ics = 50%, 50 Hz, 16 KA Breaking capacity, 415 Volts blanking plates including making good disturbed surfaces complete all as specified and directed.

Dismantling of existing unserviceable MCB distribution board and S&F, sheet metal enclosure DB concealed with wall having facility to fix MCCB as incomer and MCBs in outgoing, TP vertical type 4 way of double door, IP 43 protection complete fitted with bus bars, neutral links, G frame including S&F, 3 pole MCCB 100 Amps capacity, 50 Hz, 16 KA breaking capacity, 415 Volts blanking plates Ics = 100% including making good disturbed surfaces complete all as specified and directed.

S&F in replacement Sheet steel metal enclosure distribution box double door, SPN MCB DB double door SPN for MCB 8 Way, 240Volts, IP-43 protection flush mounting CRCA powder coated with 200 Amps rated bus bar complete all as specified and directed.

S&F in replacement Sheet steel metal enclosure distribution box double door, SPN MCB DB double door SPN for MCB 4 Way 240Volts, IP-43 protection flush mounting CRCA powder coated with 200 Amps rated bus bar all as specified.

S&F, LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC 1201m / W 10 KV surge protection, IP-20 protection recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed.

S&F, LED lights fitting 1 x 22W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size 1201m / W from ceiling rose complete all as specified and directed.

S&F, surface LED fitting for Main Enterance of Building, 34 W, lumen output 1201m / w, 230v energy efficient, with drive 10 KV, surge protection etc. complete with mounting arrangement and all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed.

Supply and fix biulding security lights 30 W, 230 volts, lumen output 1201m / w, with pressure dia cost powder coated LED stree light suitable for bldg light clear acrylic cover and complete accessories including drive with suitable complete all as specified and directed.

M&L for sub main wiring with single core PVC insulated unsheathed, 1100 Volts grade, copper cable 4 x 10 sqmm stranded conductor and drawing through and including rigid medium grade PVC non metallic concealed conduit of suitable size with conduit accessories such as junction boxes, bends, tees etc. including continus earth wire PVC insulated unsheathed 1100 volts grade, 2 x 10.00 sqmm copper conductor and connected to common earth dolly complete as directed including taking down old submain wiring all as specified. Note: One run of PVC conduit two runs of 4 x 10 sqmm cable and two run of 10 sqmm of earth wire shall be measured and paid as one unit.

All as per item No. 129 above, but with 4 runs of 6 Sqmm copper cable and 2 x 6 Sqmm as earth continuity conductor.

M&L for sub main wiring with single core PVC insulated unsheathed, 1100 Volts grade, copper cable 2 x 6 sqmm stranded conductor and drawing through and including rigid PVC non metalic concealed conduit of suitable size with conduit accessories such as junction boxes, bends, tees etc. including continus earth wire PVC insulated unsheathed 1100 volts grade, 1 x 6 sqmm copper conductor and connected to common earth dolly complete as directed including taking down old submain wiring all as specified. Note: One run of PVC conduit two runs of 2 x 6 sqmm cable and one run of 6 sqmm of earth wire shall be measured and paid as one unit.

All as per item No. 131 above, but with 2 runs of 4 Sqmm copper cable and 1 x 4 Sqmm as earth continuity conductor.

Removing of old UNSV conduits and S&F DLP U PVC adaptable trunkintg system of three section with accessories for mounting of Equipment Control Wires, Telecommunication Wires and electrical Cables with mounting. Note (One Running Meter include with Base body 150 x 50mm, flexible full Cover width of 40mm, Seperation partition for 105 x 50 Trunking, Base Joint (Body Joint - fro aligninng bases for installation, cover joint for 40mm width, Left or right end Cap & Internal / External Angle.) all as specified.

S&F, metallic body exhaust fans AC single phase 230 / 240 V, 50 Hz 1400 rpm, 4 blades, air delivery 6120 m3h of size 450 mm sweep with louver complete all as specified and directed.

Supply, fix, test & commissioning of fire alarm control panel analogue addressable microprocessor based networkable 4 loop type complete with battery backup with sealed lead acid batteries 24 Volts DC 2 x 17 Ah. The panel fabricated by CRCA sheet not less than 1.6mm thickness powder coated of operating voltage 230 volts complete all as specified and directed.

Supply, fixing, commissioning & testing of the analog Addressable multi sensor smoke / Heat detector complete with base plate and fixing arrangements complete all as specified and directed.

Supply, fixing, commissioning and testing of the analog Addressable Sounder with fixing hooters shall be 240VDC operated, the maximum sound level shall be 100db @ 10 feet complete all as specified and directed.

Supply, fixing, commissioning and testing of the analog Addressable fault isolators complete all as specified and directed.

Supply, fixing, commissioning and testing of the analog Addressable Manual Call Point complete all as specified and directed.

S&F, response indicator for analog addressable complete all as specified and directed.

M&L for 2 x 1.5Sqmm FRLS type 1100Volts grade copper condutor cable single core, PVC insulated sheathed standard cable drawn through and including PVC conduit medium grade of 25mm dia surface type complete conduit accessories and fixing clamps, complete all as specified and directed.

Supply, installing & testing of I/O Module complete all as specified and directed.

S&F, PVC conduit pipe medium grade 20mm in dia with all accessories concealed in wall suitable for drawing cables and making outlet points of cable at every 1.5 to 2 mtr gap and closing the holes by using blank plates on every point, complete all as specified and directed.

PAVAN ENTERPRISES

M/S GDR CONSTRUCTIONS