CWE/P-29/2020-21 SPECIAL REPAIR TO BLDG NO. T-133/01 TO 08 (ORS MD ACCN) AT BASOLI UNDER GE BASOLI

Amount

Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level), complete all as specified and as directed.

Taking down chowkats or frame with shutters (without taking off shutters from the frames) area not exceeding 1.5 Sqm each including taking out holdfast complete all as specified.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) area exceeding 1.5Sqm and not exceeding 4Sqm each including taking out holdfast complete all as specified and directed.

Taking down shutters of any description exc 1 Sqm but not exceeding 2Sqm each refixing in same opening.

S & F 1.25mm thick pressed steel frames 125 x 60 mm with one or more rebates with one coat of red oxide primer including necessary fixing lugs/holdfast duly tarred with bitumen and sanding with sharp clean sand, ISI marked 100 mm size hinges, lock strike plate, including cement concrete type B 0, 1:3:6 (using 12.5 mm graded stone aggregate) as in filling hollow of frame with plain cement concrete and holdfast after taaring of hollow portion of frame complete all as specified and directed

M & L 1.25mm thick pressed steel frames 105 x 60 mm with one or more rebates with one coat of red oxide primer including necessary fixing lugs/holdfast duly tarred with bitumen and sanding with sharp clean sand, ISI marked 100 mm size hinges, lock strike plate, including cement concrete type B 0, 1:3:6 (using 12.5 mm graded stone aggregate) as in filling hollow of frame with plain cement concrete and holdfast after taaring of hollow portion of frame complete all as specified and directed.

S & F Plain framed factory made 35mm thick shutter of 2nd class hard wood rail & style (two panel) with lock rail and panel of 9mm BWP commercial plywood or 12 mm veneered particle board with commercial veneering on both faces , the size of rail and style as per IS 1003 (Part-1) kiln seasoned and pressure treated including one coat of pink primer all as specified.

M & L Glazed and skelton shutters factory made 35mm thick of 2nd class hard wood rail & style open rebated and prepared to receive glass or wire gauze etc. shutters (without sash bars), size of members of shutters as specified in SSR Part-1, secton 8, clause 8.24(a) kiln seasoned and pressure treated including one coat of pink primer all as specified.

M & L Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube,necessary fixing lugs/holdfast duly tarred with bitumen and sanding with sharp clean sand, supplying & fixed complete alll as specified and shown in relevant drg

S & F Factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with Particle Board Core 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on front face & 2mm Plain colour PVC Sheet on back face, supplying & fixing in frame at site as per specification.

M & L 18/19mm thick prelaminated particle board interior grade one side with decorative choice lamination and other side balancing white lamination fixed with screws as in cup board shutters, complete all as specified.

M & L Steel window/Ventilator factory made out of box type and shutter (double shutter) with sash bar made out of section using flash butt welding, hinges shall be provided to both shutters complete including all fittings over a shop coat of red oxide primer all as per drg No CEPZ/TD/245/01 Sh 1/1, CEPZ-TD/246/01 Sheet 1/2 (double for mosquito proof one glazed with glazing bars and one gauged with glazing bars ) with side hung shutters including projecting type hinges non friction with 3mm thick 100mm long handle and two nos tower bolts 100mm long welded on 3.0 mm thick plate to each window shutter and including hold and fast and painting with one shop coat of zinc chrome primer and Sheet 2/2 all as specified and directed by Engr-in-Charge.

S & F Framed work such as grills, grating etc with ends of bars shouldered and or riveted, or forged into spikes, framed guard bars, barrel, iron doors, ladders, balusters, walkway, frame work of water tanks and similar work confirming to Fe-290 Gde E-165 complete all as specified.

S & F 3 mm thick sheet glass ordinary quality and glazing with oil putty in square not exceeding 0.5 sqm in each pane complete all as specified.

S & F Galvanised mild steel wire cloth 0.56 nominal dia of wire and average width of aparture 1.18mm and fixed with tinned tacks or galvanised wire staples, complete all as specified.

Preparation new steel surfaces of any description not otherwise described, over 10cm width or girth and applying two coat of synthetic enamel paint complete all as specified.

Preparation new wooden surfaces of any description not otherwise described, over 10cm width or girth and applying two coat of synthetic enamel paint complete all as specified.

Preparation old treated wooden surfaces of any description not otherwise described, over 10cm width or girth and applying two coat of synthetic enamel paint complete all as specified.

S & F Hasp and staple, 75 mm long aluminium anodised, including bolt to hinge plate and fixed with screws complete all as specified. ISI Marked

S & F Butt hinges, 100 mm size ISI marked, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21, complete all as specified.

S & F Extruded aluminium alloy handles, fabricated type, anodised of size 125mm ISI marked and fixed, complete all as specified and directed.

S & F Aluminium anodised, barrel tower bolts of extruded section of size 150mm ISI marked and fixed, complete all as specified and directed.

Supply and fixing in repairs, 300mm mild steel ordinary rat tail rod pattern springs including roller and roller plate, ISI marked complete all as specified.

S & F MS barrel tower bolt 150mm long, stove enameled black with bright bolt and fixed all as specified.

S & F mild steel 125mm long prssed handle oval tupe dtove enameled black ISI marked complete all as specified.

S&F for stainless steel sliding door bolts, plate type, with stainless steel bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified.

S & F aluminium hat pegs, solid body, 125mm to 175mm complete all as specified.

S & F aluminium wardrobe hooks (single) 50 to 60 mm complete all as specified.

S & F Harrison rails(Curtain rails),ISI marked mild steel chromium plated wih fixing brackets, stops, rollers etc. all as specified.

M & L Rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement incl taking down cement plaster on brick or concrete surfaces in any description etc incl raking out joints, hacking for key , scrubbing down with water complete all as specified and directed.

M & L Rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 finished even and smooth without using extra cement incl taking down cement plaster on brick or concrete surfaces in any description etc incl raking out joints, hacking for key , scrubbing down with water complete all as specified and directed.

M & L Rendering 05 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:3 finished even and smooth without using extra cement incl taking down cement plaster on brick or concrete surfaces in any description etc incl raking out joints, hacking for key , scrubbing down with water complete all as specified and directed.

Preparation of new plastered surfaces of walls and applying two coats cement base paint of approved brand all as specified and as directed .

Preparation of newly plastered surfaces and applying two coats of dry distemper, white or tinted complete all as specified

M & L for Applying three coats of white wash including preparation of newly plastered surfaces of ceiling complete all as specified.

M & L Preparation of old plastered surfaces of walls and applying one coat of cement base paint of approved brand all as specified and as directed .

Preparation of old plastered surfaces and applying one coats of dry distemper, white or tinted complete all as specified

Applying one coat of white wash including preparation of old plastered surfaces of ceiling complete all as specified.

M & L Plain Cement Concrete 1:3:6, type C-2, (using 40mm graded crushed stone aggregate) 75mm thick as in plinth protection etc laid in alternate bays finishing even and smooth without using extra cement complete all as specified.

M & L 40 mm thick PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in floor finishing surface even and smooth without using extra cement,complete all as specified and as directed.

S & F glass dividing strips, 3mm thick and 38mm width, and inserted in position to conform to design. All as specified.

M & L Glazed ceramic coloured tiles in skirting/dado 450 x 300 x 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match required shade over and including 10 mm thick cement plaster in cement mortar 1:4 as in backing coat rough finished surface including dismantling floor, hearth, or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified.

M & L Non-skid cermic coloured tiles 7 to 8 mm thick (square / rectagular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, over screed bed 15 mm thick in cement mortar 1:4 including dismantling floor, hearth, or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified.

M & L machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete 15mm thick screed bed in CM 1:4 , complete all as specified.

M & L 20mm thick granite (of approved type colour) work (table rubbed & polished) in jambs, pillars, window cills, cooking plateform laid over and including 15mm thick cement screed (1:4) and jointed with grey cement slurry and pointed with white cement (1:2) with admixture of pigment to match the colour of granite stone including cutting and and moulding the edges, complete all as specified.

M & L PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in sunken portion all as specified and directed by Engr –in Charge

Supply and fixing in repairs, Vitreous china squatting pan (Orissa pattern) ISI marked size 580 x 450 mm, white, with integral foot rests, complete connection to drain (outgoing pipe) and to flushing pipe of 32mm dia and syphonage pipe etc, and complete, all as specified and as directed.

S & F vitreous china Wash hand basin, white, oval shape of size 550x400mm including brackets, brass chromium plated waste coupling, and waste pipe PVC 32mm dia including cutting for and pinning in ends of brackets or erecting stand etc fixed in repair, complete all as specified.

Dismantling water tanks and removing to store capacity exceeding 250 ltr and not exceeding 500 ltr complete all as specified.

S&F Rotational moulded polythene water storage tank, coloured, tripple layer cylindrical vertical with closed top 500 litre capacity hoisted and fixed in position, including inlet and outlet pipe connections, 20mm dia and 15 mm dia GI pipes medium grade respectively, 20mm GI pipe medium grade over flow pipe 15 cm long wash out with plug and including brass ball valve 20mm, high pressure with polyethelyne float and fly nutscomplete all as specified and directed.

S & F in repairs PVC valve less symphonic action type flushing cistern 10ltr capacity , low level white with inlet ball valve float and handle including brackets including 32mm dia PVC. flush pipe for low level cistern including all joints, complete all as specified.

Supply and fixing in repairs, 100 mm dia cast iron 'P' or 'S' trap ISI marked complete all as specified.

S & F in replacement 75mm bore cast iron floor trap with grating including jointing to waste pipe fixed in cement concrete type B-1 , 1:2:4, all as specified dia of outlet, plain with grating including jointing with solvent cement fixed, complete all as specified.

Supply and fixing in repairs, 100 mm dia cast iron soil waste and vent sand cast pipe ISI marked in any length with or without ears with lead joints laid in floor/wall, complete all as directed

Supply and fixing in repairs, 75 mm dia cast iron soil waste and vent sand cast pipe ISI marked in any length with or without ears with lead joints laid in floor/wall, complete all as directed

Supply and fixing in repairs, Cast iron bends (any radius) diminishing pieces or tapers (larger bore measured), ISI marked bore of pipe 100mm, complete all as specified.

Supply and fixing in repairs, Cast iron bends (any radius) diminishing pieces or tapers (larger bore measured), ISI marked bore of pipe 75mm, complete all as specified.

Supply and fixing in repairs, Cast iron branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branchs, ISI marked bore of pipe 100mm, complete all as specified.

Supply and fixing in repairs, Cast iron branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branchs, bore of pipe 75mm, complete all as specified.

S&F PVC connection 15mm size with PTMT nuts on both ends of length 450mm , ISI marked complete all as specified.

S&F Shelf of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats(minimum weight 300gms) ISI marked complete all as specified and directed.

S&F in repairs Tubular towel rail, chromium plated, 20mm dia, D type, 60 cm long between flanges complete all as specified and directed.

Supply and fixing in repairs stop valve/angle valve of cast copper alloy chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions 15 mm bore, complete all as specified.(weight not less than 400gms each)

S & F 15mm bore pillar tap cast copper alloy with capstan head, fancy type, chromium plated, screwed down, high pressure, with or without lettered 'Hot or Cold' with long screwed for iron pipe fixed in repair complete, all as specified & directed

Supply and fixing in repairs Bib tap cast copper alloy with screw down for iron pipe 15 mm bore long body, complete all as specified.(weight not less than 400gms each)

Supply and fixing in repair chromium plated shower roses with or without swivel joints 125mm size including fixing to steel pipe or union

Supply and fixing in repairs stop valve of cast copper alloy chromium plated with long shank concealed type screwed down high pressure screwed both ends for iron pipe or for unions 15 mm bore, complete all as specified.

S&F Stainless steel sink with drainage board, 1mm thick for kitchen or laboratory wih plugs, washers and wastes including fixing bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mmx460mm bowl size 410mmx330mmx160mm fixed, complete all as specified.

S&F Waste coupling of PTMT (half or full threaded) (Minimum weight 32mm-45gms) for 32mm bore dia of discharge pipe to WHB, sink, ISI marked complete all as specified.

Taking up or down GI pipes of 15mm bore and connection including cleaning for refixing or removal unserviceable pipe from the site all as specified and directed.

Taking up or down GI pipes of 20mm bore and connection including cleaning for refixing or removal unserviceable pipe from the site all as specified and directed.

M & L cutting chases pinning in brick work for concealing water tubing and making good to facing where required and pointing in cement mortar 1:3, cutting and executing 10 cm girth as all specified.

Refixing old steel tubing connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store with all fittings of 15 mm bore, complete all as specified and directed.

S&F Steel water tubing of 15 mm bore ‘medium grade’ galvanized with all fittings fixed to walls and ceilings or laid in floors, complete all as specified.

Refixing only old steel water tubing of 20mm bore and connections in new or old position fixed to walls, ceilings and floors etc. including fittings as required, complete all as specified.

S&F Steel water tubing of 20 mm bore ‘medium grade’ galvanized with all fittings fixed to walls and ceilings or laid in floors, complete all as specified.

M & L 10mm thick cement plaster rendering in cement mortar 1:3 on fair faces of stone masnory/brick or concrete surfaces & finishing the surface even and smooth without using extra cement as in facia/chhajja & roof projections incl taking out peeled off plaster/concrete making the line in true surface , complete all as specified.

Preparation of newly plastered or unplastered surfaces of wall /facia/Chajjas etc of any description over 10cm width or girth not otherwise described and applying two coat of weather proof exterior emulsion paint over a coat of primer complete all as specified

Dismentalling of asbestos cement ( corrugated, semi-corrugated, etc) sheet in roof covering complete all as specified

M & L rolled mild steel works as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam,tee,angle, channel or flat sections) including distance pieces, incl a shop coat of zinc chromate primer paint

M & L Mild steel screw bolts exceeding 11 mm but not exceeding 15mm dia at neck, machine made, with hexagonal or square heads at one end and screwed the other, or screwed both ends; each screwed and to be fitted with washers and one hexagonal or square nut exceeding 10cm and not exceeding 15cm long complete all as specified and directed.

M & L Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified.

M & L Pre- painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified.

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) any thickness including cover fillets all as specified & directed

Dismantling of timber scantling under 40sqcm and over in section unframed work,as in fillets, rails, posts, rafters, purlins etc , complete all as specified.

Dismantling of timber scantling 40sqcm and over in section unframed work,as in any position, complete all as specified.

Dismantling wrought iron or mild steel work of any description complete all as specified and directed.

S & F 10mm thick PVC insulation panel with EPS stuck to 1 mm plain PVC sheet suitbaly placed in false ceiling grid madeof auminium /GI/MS as per specification and drawing complete with 6mm GI hanging chanelincluding necessary fixers, drilling, fasteners etc complete all as specified and directed by Eng-in-Charge

Taking down carefully copper/ aluminium unserviceable/ perished point wiring (light, fan, socket or power complete including fixture and fittings such as switches, ceiling roses, pandents, regulators, sockets, light fittings,removing material from site for taking credit etc and making good disturbed surfaces of wall, floors, complete all as specifiecd and directed.

M& L Point wiring for light/fan controlled by one switch with 1.5 sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS with and including PVC rigid conduit (medium grade) having thickness as per IS code with all fittings including galvanised pressed steel sunkum boxes having thickness as specified 3mm bakalite laminated sheet for switches and sockets, including 1.5sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS as earth continuity conductor connected to common earth dolly including cutting, chiseling for concealed piping and making good disturbed surface area and white wash/colour wash to matching with the existing colour complete all as specfied and directed. Note : (a) Colour coding is to be maintained (Ph-Red, N-Black, Half -Yellow, Earth- Green) (b) On RCC roof ceiling PVC conduit shall be provided on surface for fan with proper fixing clips all as directed.

M&L Point wiring for light controlled by two numbers single pole 2 way switch with 1.5 sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS with and including PVC rigid conduit (medium grade) having thickness as per IS code with all fittings including galvanised pressed steel sunckun box having thickness as specified with 3mm bakalite laminated sheet for switches and sockets, including 1.5sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS as earth continuity conductor connected to common earth dolly including cutting, chiseling for concealed piping and making good disturbed surface area and white wash/colour wash to matching with the existing colour complete all as specfied and directed. Note : (a) Colour coding is to be maintained (Ph-Red, N-Black, Half -Yellow, Earth- Green) .

All as per above item no 91 here in before but for one 3 pin socket outlet 5 amp on independent board all as specified and directed.

All as per above item no 91 here in before but for one 3 pin socket outlet 5 amp on same board all as specified and directed.

All as per above item no 91 here in before but for one bell/buzzers point controlled by one bell push button on the same board with other switches or independent with cable 1.5 sqmm size all as specified and directed.

M&L Point wiring with 2.5 sqmm FRLS, PVC insulated and unsheathed multi stranded flexible copper conductor cable 1100 Volts grade ISI marked using proper colour coding (Phase-Red, Neutral-Black drawn in and including rigid PVC concealed conduit medium grade of suitable size with sunk case iron/pressed steel terminal boxes of adequate size with suitable thickness plastic laminated sheet cover for one 3 pin socket outlet 15 Amp on independent board including continuous 2.5 Sqmm FRLS, PVC insulated and unsheathed copper conductor cable (multistranded) as earth wire to common earth dolly, complete all as specified and directed.

S&F Switch piano flush type 5 Amp single pole one way, (ISI marked), complete all as specified.

S&F Switch piano flush type 5 Amp, single pole, two way (ISI marked) complete all as specified and directed.

S&F Socket outlet 2 & 3 pin 5 Amp flush type (ISI marked) all as specified & directed.

S&F Socket outlet 2 in 1, 3 pin, 5 & 15 Amp flush type universal,(ISI marked) complete all as specifed.

S&F Switch bell push flush type 5 Amp single pole one way (ISI marked) complete all as specified

S&F Switch piano flush type 15 Amp single pole one way, (ISI marked), complete all as speciied.

S&F Stepped type electronic fan regulator 0 to 4 step , flush type heavy duty (ISI marked) complete all as specified.

S&F Lamp holder PVC/Polycarbonate type with back plate having matching colour to holder for angle/batten fittings (ISI marked) complete all as specified and directed.

S&F Bell, Ding dong AC 230Volts single pole (ISI marked) complete all as specified and directed.

S&F Ceiling rose, 3 phase/bakelite 65x50mm two or three therminals isolated body fixed on PVC round block (ISI marked) complete all as specified.

S & F LED Tube light fitting 20 watt , 230 volts, industrial box type complete with bipin holders,connector block and retro LED rod of 20 Watt, 4 feet long with aluminium housing provided for efficient heat dissipation with polycarbonate diffuser having high efficacy (double side connection) complete with all accessories internally prewired batten (double side connection) and including making connections with 3 core twisted flexible copper cable of size 23/.0076 from ceilling rose/PVC connector to light fittings ,complete all as specified and directed. Note: (i) Contractor shall produce LM 79 & LM 80 test report form OEM owned NABL accredited laboraory. (ii) Contractor shall give gurantee of complete fitting/ fixtures for minimum of 2 years form the date of completion. (iii) Contractor shall conduct the inspection of company representative at site before installation of fittings/fixtures at no extra cost. (iv) Contractor shall arrange arrange 70% material at site for approval of GE before incorporation in the work.

S&F in replacement LED bulkhead fitting luminaries with opal diffuser including (LED lamp type 10 watt LED 6000 K), lamp holder etc connecting electricaly to ceiling rose using cord flexible 3 core PVC insulated over all sheathed with flexible copper conductor of size 0.75 sqmm all as required complete all as specified and directed.

S&F Sheet metal enclosure factory made (Double door) for DBs, single pole and neutral, 240 volts, 50 Hz, 8 way with 200Amps rated bus bar fixed on walls, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning, complete all as specified.

S&F MCB SPN 32 Amp, 240V with 10KA breaking capacity of 'C' series in distribution boards all as specified and directed.

S&F MCB SP 05 to 32 Amp, 240V with 10KA breaking capacity of 'B' series in distribution boards all as specified and directed.

Supply and laying in repairs of existing circuit/submain wiring alongwith two single core cable PVC insulated and unsheathed cable with copper conductor FRLS (multistrand) of size 6 sqmm drawing in and including concealed PVC rigid non metallic conduit heavy duty thickness not less than 2mm and size not less than 25mm dia and single core cable PVC insulated and unsheathed cable with copper conductor FRLS (multistrand) of 6 sq mm as earth wire including cutting chases in brick wall, rendering in cement mortar 1:4 and making good the disturbed surfaces to match existing complete all as specified & directed. Note: Two runs of 6 Sqmm single core PVC insulated copper conductor cable(FRLS) and one run of 6 sqmm copper conductor cable (FRLS) as a earth lead and one run of PVC conduit wiil be measured as a one unit.

M&L Earthing complete with galvanised steel earth plate electrode of size (600 x 600 x 6) mm thick buried directly into ground vertically to depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level, surrounded on all sides by alternate layers of 150 mm thick charcoal and common salt, connected to galvanized earh lead wire of size 4.0 mm by means of lugs, bolts, nuts, washer, check nuts of galvanised iron or steel all as shown in Electrical plate No. 3 of SSR Part I, wire protected by dia 15 mm bore light grade GI Pipe laid in floor and fixed to wall with proper size of clamps and watering pipe of bore 20 mm dia GI medium grade including wire mesh funnel, PCC, earth chamber pit with PCC 1:2:4 type B-1 using 20 mm grade stone aggreate including form work cement mortar including CI Pit cover with frame necessary excavation and earth work in any type of soil including testing on completion for desired result all as specified. Note: The rate quoted include cost of 7.5 metre earthing wire with protection pipe.

Taking down ceiling fan/exhaust/cabin fan of any make & sweep from exiting position of any height and carrying out cleaning and servicing, greasing bearings and replacing block pin and refixing in existing/new location after repair work of bldg and connecting up with new 0.5 Sq mm 3 core PVC insulated flexible core copper wire multistrand all as specified and directed.

Supply laying jointing and testing LT XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 16 sqmm 4 core complete all as pecified. Note : Earth work , sand cushioning, GI pipe , brick covering for mechanical protection will be measured and paid separately under respective item of Schedule.

S&F DWC high density polyethelene pipes in replacement having 63/50outer dia mm, inner as per site requirement having corrugation on the wall and plain surface on the inner wall conforming to IS: 14930(Part I & II) for protection of underground cable laid along pole/along wall/in PCC on GL/roof and including all fittings as required at site including aking down the old unserviceable complete all as specified and directed. Make -Trupati /Equivalent

Excavation in trenches not exceeding 1.50m wide and not exceeding 1.50m in depth for foundation laying poles, stay assembly and laying of LT/HT cables in any type of soil and getting out, complete all as specified.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25cm, in any type of soil, complete all as specified and as directed.

Removal of excavated material (soil) to a distance not exc 50m and depositing where directed at a level not exceeding 1.5mtr above starting point complete all as specified and directed

S&F in replacement sheet metal powder coated VTPN DB double door 4 way provisioned with including 01 No. MCCB 63 Amps, 415 Volts, 50 Hz AC 16 KA 4 pole with copper bus bar rated 200 Amps neutral link, earth bar and din rail for fixing the MCBs complete all as specified. Note :- MCBs shall be measured and paid separately in relevant item of BOQ

Notes : The Schedule of Credit amount shall be deducted from the total of this schedule(BoQ) to arrive at Contract Sum.

Neeraj Enterprises