REPAIR/MAINT/REPLACEMENT STREET LIGHT HIGH MAST FLOOD LIGHT GATE LIGHT GARDEN LIGHT AND CONNECTED WORKS AT SUB STN OF CHCC BH SHO SOI PDA CMDC ECHS AND COLLEGE OF NURSING AT AGE E/M (HOSP) UNDER GE E/M LUCKNOW

Amount

Dismantling of concrete poles any type any size complete all as specified and as directed by Engineer-in-Charge.

Supplying and laying or fixing in replacement, jointing and testing LT under ground electric power cable crossed linked polyethylene ( XLPE) insulated, galvanised steel strip or wire armoured, ISI-7098 Marked, with aluminium conductor multi stranded , heavy duty 1100 Volts grade of size 10 sqmm cross sectional area, 2 core ,complete all as specified laid in trenches/ laid under floor or fixed naked with walls / on poles/ in ducts /in GI pipes etc. with and including MS Clamps, nuts , bolts, washers complete all as specified and directed. Note :- Excavation, earth work, sand cushioning, protection bricks/ tiles/ block and pipe shall be measured and paid separately under appropriate items.

- do - but of size 10 Sqmm 4 core

- do - but of size 16 Sqmm 4 core

- do - but of size 25 Sqmm 3.5 core

- do - but of size 35 Sqmm 3.5 core

- do - but of size 50 Sqmm 3.5 core

-- do-- but size 70 sq mm 3.5 core

- do - but of size 95 Sqmm 3.5 core

- do - but of size120 Sqmm 3.5 core

- do - but of size185 Sqmm 3.5 core

- do - but of size 240 Sqmm 3.5 core

Excavating in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth for laying of cables, pipes etc. and getting out including trimming the sides and forming bottom surfaces to required levels in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, and well ramming in layer not exceeding 25 cm thick in soft/loose soil complete all as specified and directed.

Removing excavated material ( soils) not exceeding 50m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified.

Material and labour for river sand, washed and screened dry for cushioning to under ground cable in trenches below and around under ground cable including spreading and levelling complete as specified and directed . Note :- Punned thickness shall only be considered for payment

M&L laying well burnt old size bricks, sub class "B" bricks, straight or curved on plan , laid flat with width equal to length of brick , laid dry over electric cable for protection complete all as specified & directed by Engr-in-Charge.

Boring of hole under road/pavement/hard standing or any other situation by manual means and suitable for passing of GI pipe 40 to 100 mm bore and making good both ends all specified and directed

S & F GI tubing 'Light' grade 40 MM for cable protection fixed in poles/walls/laid under roads/crossing etc incl taking out the rusted pipes of following sizes, complete all as specified and directed.

- ditto - but size 50 mm bore dia

- ditto - but size 80 mm bore dia

Disconnecting faulty 1.1 KV LT cables of any size and any length from both ends Hiring of cable fault detector machine to detect exact position of fault , removal of Fault, Re-connections and testing of cables after removal of fault etc complete as specified and directed. Note : (a) 1.1 KV LT cable & joints shall be measured and paid for seperately under respective items of schedule. (b) Contractor or his rep shall come to the site of breakdown within one hour of notification of breakdown alongwith fault locating machine and manpower. In case the rep or contractor shall not come to the site of breakdown and not to start attending breakdown within 1.00 hour a penalty of Rs 1000 per fault per hour will be imposed over contractor and will be deduct from his dues.

Taking out faulty underground 1100 Volt LT cable of different sizes after excavation and removing bricks of any size and relaying in the same trenches or re routing after rectification of fault by straight through joint complete all as directed. Note: (a) 1100 Volt LT cable & joints will be measured and paid for seperately under respective items of schedule. (b) Retrieved old serviceable bricks will be laid in trenches for cable protection. If extra bricks and sand required at site shall be measured and paid separately under respective items of BOQs. (c) Excavation and earth work will be measured and paid for seperately under respective items of schedule.

Material & Labour for writting of existing pole with stencil out with white colour in black background and preparation of old painted surface of steel tubular pole 9 meter long above coping) and applying two coat of aluminium paint, making of strip of 300mm width (balck and yellow in alternate band) upto 1500 mm height with one synthetic enamel paint , rewriting pole No by painter with enamel paint, and painting the existing MS clamp with one coat of aluminum paint complete all as specifeid and directed.

Supply drawing, connecting and testing in replacement 3 core, 1.5 Sqmm PVC insulated and PVC round sheathed`copper conductor (flexible) industurial cable, 1100 Volts conforming to IS 694 in steel tubular poles from Junction box to street light fitting including providing suitable copper lugs all as specified and directed by Engr-in-charge.

Supply drawing, connecting and testing in replacement 3 core, 2.5 Sqmm PVC insulated and PVC round sheathed`copper conductor (flexible) industurial cable, 1100 Volts conforming to IS 694 in steel tubular poles from Junction box to street light fitting including providing suitable copper lugs all as specified and directed by Engr-in-charge.

Supplying and fixing in repair flat twin core ,6 sqmm nominal cross sectional area multistranded aluminium conductor FRLS cable, PVC insulated and sheathed 1100 Volts grade complete all as specified.

M&L for removal of existing paint from external surface of LT panel by scrapping, making good distrubed surfaces by applying putties on uneven surface to make it even and M&L for spray painting to LT panel of any size with two coat of synthetic enamel paint with desired colour over one coat of red oxide primer complete all as specified and directed.

Supply and fix in replacement CRCA MS sheet for LT panel having thickness 3.15 mm powder coated finish over one coat of red oxide on out side surface and painted in side with two coats of red oxide primer including all fixing acessories i.e. suitable size of hinge, nuts, bolts, washers, cutting and welding works etc complete all as directed by Engr -in-charge

M & L for MCCBs four pole 27 KA, fixed type incl taking out unserviceable MCCB's and connecting,of capacity 100 AMPS Legrands or equivalent as per spacified and directed

M & L for MCCBs four pole 27 KA, fixed type incl taking out unserviceable MCCB's and connecting,of capacity 125 AMPS Legrands or equivalent as per spacified and directed

M & L for MCCBs four pole 27 KA, fixed type incl taking out unserviceable MCCB's and connecting,of capacity 160 AMPS Legrands or equivalent as per spacified and directed

M & L for MCCBs four pole 36 KA, fixed type incl taking out unserviceable MCCB's and connecting,of capacity 250 AMPS Legrands or equivalent as per spacified and directed

M & L for MCCBs four pole 36 KA, fixed type incl taking out unserviceable MCCB's and connecting,of capacity 400 AMPS Legrands or equivalent as per spacified and directed

M & L for MCCBs four pole 36 KA, fixed type incl taking out unserviceable MCCB's and connecting,of capacity 630 AMPS Legrands or equivalent as per spacified and directed

Digital type Volt meter ( 0-500 V ) , 3 ph , class 1 including taking down unserviceable voltmeter, complete all as specified and directed.

Digital type Ammeter (0-300 A) ,3 ph , class 1 including taking down unserviceable ammeter, complete all as specified and directed.

Indicator lamps (LED Type) including taking down unserviceable indicator lampsall, complete all as specified and directed.

S & F in rep MCB’s single pole with neutral, 6 to 32 Amps, 250 volts with 'B curve, fixed in existing PVC box including connecting complete.

Disconnecting the LT cable from Panel / Pole, preparing the end for jointing including all earth work, Supply and fixing straight through heat shrinkable joint suitable for LT XLPE cable of size 3.5/4 core 10 to 16 sq mm

All as per item Ser No 40 above but size 25 to 50 Sqmm

All as per item Ser No 40 above but size 70 to 120 Sqmm

All as per item Ser No 40 above but size 150 to 185 Sqmm

All as per item Ser No 40 above but size 240 to 300 Sqmm

Supplying, transporting, erecting and fixing Steel tubular swaged poles type 410 SP-31 ( 9.0 metres long) complete with cast iron base plate, finial, taper plug, bolts, nuts and screws as specified, including necessary excavation and earth work , PCC 1:4:8 type D2 in foundations below pole, PCC 1:3:6 type C2 around poles and PCC 1:3:6 type C1 as in plinth block , disposal of surplus soil to a distance not exceeding 50 m and depositing where directed, painting steel tubular poles exposed surafces with Aluminium paint two coats over one coat of red oxide primer and providing 300 mm wide bands (3 bands/ straps with synthetic enamel paint and 2 bands with Black bituminous paint ) from plinth block and numbering of poles , painting embedded portion of poles with one coat of bituminous paint complete all as specified and directed.

Supply and errection in replacement of 07 mtr continuously tapered hot dip galvanised Octagonal cross sectional pole with single dipping method having bottom 130 mm A/F and top 70 mm A/F 3 mm thick confirming to ASTM A 572 Gr with yield 450 mpa cut and folded to form an octagonal section and welded in accordance with AWS for wind loading as per IS 875 part 3 1987.Poles shall be provided with base plate of size 225x225x12 mm which shall be free from any lamination or incursion with no cutting or welding on the pole after hot dip galvanising with single arm 1000 mm long bracket tilted to 150 degree from horizontal toward vertices suitable for mounting on the octagonal pole including all Rcc work , of company recommendation complete all as specified and directed.

S&F in replacement wheather proof pole mounting PVC junction box, base and door of junction box made out of SMC having outside dimention 333x233x120mm, inside dimention 300x200x105mm , single door front openable provided with hinged cover and locking arrangements with 4 Nos aluminium bas bar 63 Amps, mounted on porcelin insulator including M&L for MCB SP 10 Amp -1No, fixed on box in Din rail complete with electrical connection fixed to pole with suitable size FI clamp nut bolts and washer including embossing/painting of danger notice of size not less than 10cm x 7.5cm with letters, figures and conventional skull and bones in signal red colour on front face of junction box body Complete all as directed by Engr-in-Charge

S & F Offload change over switch, 200 Amps, 415 volts, 4 pole in sheet metal enclosure conforming to IS:13947 (Part-3); IEC:60947-3 with locking facility including all connecting/ jointing materials and dismantling of existing change over switch, complete all specified & directed

S & F Off load change over switch (side operated handle) 400 Amps, 415 volts 4 pole in sheet metal enclosure with interlock door and pad lock facility including dismantling of existing change over switch, complete all specified & directed.

Supply and fixing new generation ,energy saving ,environment friendly LED GATE LIGHT fitting,fully cast aluminium body finish with polyeurethene paint with acryilic window cover with B22 brass holder suitable for 15 to20 watt led bulb as light sopurce including making connections complete all as per specified and directed by the Engr-in-Charge..

Supply and fixing new generation ,energy saving ,environment friendly POST TOP LANTERN fitting, aluminium spun lamdscape luminaires with high power LED 25 watt as light sopurce including making connections complete all as per specified and directed by the Engr-in-Charge.

Dismantling & taking out old/unsv LT panel board, supply installation testing and commisioning of LT outdoor Panel OF size – 1.5 x 1.0 x 0.50 mtr outdoor type factory made pedastal type outer fabricated out of 3.15 mm CRCA sheet and inner sheet of MS black sheet and slopy roof and spray painting two coat insiade and outside with synthetick enamle paint of approved shade over a coat of red oxide primer locking arrangement comprise 50 mm size godrage brass pad lock with duplicate keys two earthly terminal suitable cable gland for all incoming and outgoing cable grouting of feeder piller box 40 cm above ground level by providing 90 cm long angle iron of size 50x50x6 mm welded on all the for corner embeded in PCC 1:2:4 using 20 mm stone agregrate up to 50 cm deep including connection all exisiting cable with MCCB terminal all as specified and directed by EIC at the site requirment complete including the following component:-

Dismantling & taking out old/unsv LT panel board, supply installation testing and commisioning of LT outdoor Panel OF size – 1.5 x 1.0 x 0.50 mtr outdoor type factory made pedastal type outer fabricated out of 3.15 mm CRCA sheet and inner sheet of MS black sheet and slopy roof and spray painting two coat insiade and outside with synthetick enamle paint of approved shade over a coat of red oxide primer locking arrangement comprise 50 mm size godrage brass pad lock with duplicate keys two earthly terminal suitable cable gland for all incoming and outgoing cable grouting of feeder piller box 40 cm above ground level by providing 90 cm long angle iron of size 50x50x6 mm welded on all the for corner embeded in PCC 1:2:4 using 20 mm stone agregrate up to 50 cm deep including connection all exisiting cable with MCCB terminal all as specified and directed by EIC at the site requirment complete including the following component:-

M&L in replacement out door type busbar panel board (Dimention of Cubical/enclosure not less than 600mmx450mmx450mm) made out of 3.15 mm thick MS sheet and MS angle section 50x50x6 mm factory made suitable for 3 phase 4 wire 415 Volt, 50 Hz, powder coat painted comprising of the following:- (a) FP, Aluminium bus bar 500 Amps insulated with colour coded heat shrinkable sleeve and shall be mounted on suitable size “F” class insulators. (b) Incoming MCCB 250 Amps 36 KA, 415 Vots, 50 Hz, FP. – 1 No (c) LED Indicator lamp RYB - 01 set of three. (d) Platform of Panel. Platform for the busbar panel with PCC 1:4:8 type D-2 with 40 mm graded crushed stone, 15 cm thick in foundation, brick work in CM 1:6 with sub class 'B', old size bricks, rendering 15 mm thick in CM 1:6 on exposed surfaces and 100 mm thick PCC padding 1:3:6, type C-1 using 20 mm graded crushed stone aggregate on top and grouting bolts etc for panel. The platform shall be such that it is of a height 45 cm above the nearest road level.

Note :- (i) All out going feeder shall be connected by cable through suitable size gland plate / glands. (ii) The various feeders shall be indicated by 50 mm size letters in synthetic enamel white paint. (iii) All MCCB with adjustable protection for over load and short circuit and conforming to IEC60947-II/IS 13947-II (Latest Version). The MCCB should have Ics=100%Icu. The MCCBs shall have spreader links and barriers as standard feature of manufacturer

M&L Earthing complete with galvanised mild steel earth plate electrode 600x600x6.0mm thick, burried directly in ground to a depth not less than 2.25 metres deep below ground level with top edge of earth plate not less than 1.5 metre below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15 cm all around the plate, using GI strip 32 x 6 mm as earth strip electrode bolted or rivetted to earth plate at one end and connected to equipments at another end, GI earth strip encased in and including 40 mm dia GI 'light grade' pipe from upper end of earth plate upto equipments,20 dia bore GI pipe 'light grade' as water pipe from earth chamber to upper edge of earth plate, Test point , GI funnel with wire mesh fixed on water pipe and PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in pit chamber and RCC pit cover 50mm thick precast RCC 1:2:4 type B-1, duly reinforced with MS TMT bars 8mm dia @ 100 c/c both ways with 10mm dia MS round bar as in lifting handles, excavation, earth work including laying the GI pipe concealed in floor/wall all as described in electric plate of SSR Part I complete all as specified and directed and testing on completion. Note :- If the desired earth resistance is not found, earthing shall be redone by the contractor at no extra cost to the department.

M&L Earthing complete with Copper earth Plate electrode 60x60cmx3.15mm thick, burried directly in ground ( earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, Including connected to copper strip 20x3mm lead (upto 7.5 Mtr) by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate connected to earthing test point all as specified or indicated including testing on completion.ith salt to a packed thickness of 15 cm all around the plate, and including 40 mm dia GI 'light grade' pipe from upper end of earth plate upto equipments,20 dia bore GI pipe 'light grade' as water pipe from earth chamber to upper edge of earth plate, Test point , GI funnel with wire mesh fixed on water pipe and PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in pit chamber and RCC pit cover 50mm thick precast RCC 1:2:4 type B-1, duly reinforced with MS TMT bars 8mm dia @ 100 c/c both ways with 10mm dia MS round bar as in lifting handles, excavation, earth work including laying the GI pipe concealed in floor/wall all as described in electric plate of SSR Part I complete all as specified and directed and testing on completion. Note :- If the desired earth resistance is not found, earthing shall be redone by the contractor at no extra cost to the department.

Supply, fixing, connecting and testing energy saving LED street light fittings 35 Watt with thermal management, potted driver, pressure die cast housing LM 6 alloy/anti dust exposed lens, in built tilt angle arrangement and environment friendly long life with IP66 protection on existing street light poles and bracket complete all as specified and directed.

Supply, fixing, connecting and testing energy saving LED street light fittings of 60 Watt with thermal management, potted driver, pressure die cast housing LM 6 alloy/anti dust exposed lens, in built tilt angle arrangement and environment friendly long life with IP66 protection on existing street light poles and bracket complete all as specified and directed

supply and Fixing in repair, connecting and testing energy saving LED street light fittings of 120 Watt with thermal management, potted driver, pressure die cast housing LM 6 alloy/anti dust exposed lens, in built tilt angle arrangement and environment friendly long life with IP66 protection on existing street light poles and bracket complete all as specified and directed.

Supply, fixing, connecting and testing energy saving LED street light fittings of 90 Watt with thermal management, potted driver, pressure die cast housing LM 6 alloy/anti dust exposed lens, in built tilt angle arrangement and environment friendly long life with IP66 protection on existing street light poles and bracket complete all as specified and directed.

Fixing in replacement GI bracket for street light fittings fabricated with GI tubing 40mm dia 'light grade' 1.5m long and bending to angle of 120 degree including mild steel clamp of suitable size with two coat aluminium paint suitable for fixing on PCC/steel poles complete all as specified and directed.

Supply, fixing, connecting and testing energy efficient LED flood light fittings of 120 Watt pressure die cast aluminium housing and IP66 protection complete all as specified and directed.

Supply, fixing, connecting and testing energy efficient LED flood light fittings of 70 Watt pressure die cast aluminium housing and IP66 protection complete all as specified and directed.

Supply, fixing, connecting and testing energy efficient LED flood light fittings of 170 Watt pressure die cast aluminium housing and IP66 protection complete all as specified and directed.

Supply, fixing, connecting and testing energy efficient LED flood light fittings of 210 Watt pressure die cast aluminium housing and IP66 protection complete all as specified and directed.

Supply & fixing in replacement automatic street light timer panel 12 KW /40 Amp switch using Infrared Sensor based for automatic switching of street lights based on LUX level of natural light. Required illuminance for switching ON is < 30 Lux and for switching OFF > 10 Lux level. The sensor (nature switch) alongwith suitable power contactors, Input (supply) MCB and output (load) MCB(s), support terminals should be enclosed in pole/ wall mountable enclosure made of rust proof, electric shock proof, termite proof and FR graded SMC junction box conforming to IP-54 degree of ingress three phase 8 KW lightening load capacity including mounting bracket, cable glands, openable doors with lock complete all as specified & directed by Engr-in-Charge.

Supply, Installation, Testing & Commisioning in repair of exterior BIS registered RGBW Linear LED Wall Washer luminaire for facade lighting with extruded aluminium housing, powder-coated finish, Clear toughened glass of 4mm thickness and die casted end caps, of Total System wattage 24W with system lumen output 1393lm with all LEDs on, minimum system lumen efficacy 63 lm/w. Luminaire shall be capable of producing dynamic color changing light with 16 million colors as the light fixture should be programmable using 8 bit control DMX512 protocol / Ethernet based control. Luminaire shall be conforming to BIS i.e. IS 10322 (Part 5/Sec 5) and shall be complete with all necessary accessories required for proper working of fixture including weather proof connection cables, water proof connectors etc. as required.

Supply, Installation, Testing and Commissioning in repair of exterior BIS registered LED RGB flood lighting luminaire for facade lighting with Die-cast aluminium housing, powder-coated finish, Clear toughened glass of 4mm thickness, of Total System wattage 28W with system lumen output 1641 lm with all LEDs on , minimum system lumen efficacy 58lm/w. Luminaire shall be capable of producing dynamic color changing light with 16 million colors as the light fixture should be programmable using 8 bit control DMX512 protocol / Ethernet based control . Luminaire shall be conforming to BIS i.e. IS 10322 (Part 5/Sec 5) and shall be complete with all necessary accessories required for proper working of fixture including weather proof connection cables, water proof connectors etc. as required.

Supply, Installation, Testing & Commisioning in repair of exterior BIS registered LED RGBW flood lighting luminaire for facade lighting with Die-cast aluminium housing, powder-coated finish, Clear toughened glass of 4mm thickness, of Total System wattage 45W with system lumen output 2379 lm with all LEDs on , minimum system lumen efficacy 55 lm/w. Luminaire shall be capable of producing dynamic color changing light with 16 million colors as the light fixture should be programmable using 8 bit control DMX512 protocol / Ethernet based control. Luminaire shall be conforming to BIS i.e. IS 10322 (Part 5/Sec 5) and shall be complete with all necessary accessories required for proper working of fixture including weather proof connection cables, water proof connectors etc. as required.

Supply, Installation, Testing & Commisioning in repair of exterior BIS registered RGBW Flexible LED Strip with 14.4 Watt per meter. LED Strip should have 60Nos LEDs per meter through out the length with the silicon cover with system lumens 708 lms/meter and System Lumen Efficacy 49lm/w. Standard Length of LED Strip is 5 mtr and it shall be capable of producing dynamic color changing light for with 16 million colors and should be programmable using 8 bit control DMX512 protocol / Ethernet based control. The Strip should have IP 67 protection with inbuilt IP67 connectors at both ends. led strip shall be complete with all necessary accessories required for proper working of fixture including weather proof connection cables, water proof connectors etc. as required.

Lowering the high mast light , height of 25 mtr and repairs to the extent by removing connections from the system, checking of unserviceable spare parts and serviceable parts ,replacement of unserviceable parts with new spares and testing complete, tightening the loose connection and made item functional, reassembling the fitting and re-fixing/ re-hanging the same after repair in existing location and tesing complete all as specified and directed by Engineer-in-Charge. Note : (a) Spares required for repair shall be measured and paid separately as supply only items here-in-after (b) The contractor shall provide all type and safety equipment & other tools required at site to electrician for maintenance of light (c) In case any accident/injury of any person deputed by contractor shall be held responsible for setting all claims/compensation. (d) all other item also included in the works which not catered in items

(a) supply only gear box as per existing size, capacity and make.

(b) supply only motor as per existing size,capacity and make.

(c ) Supply only controll switch as per existing size, capacity and make .

Supply, installing, testing and commissioning of factory made , tested , CPRI approved powder coated LT Panel board ,cubical compartmentalized , out door type double door , plate form mounted, suitable for 415 volts, 3 phase, 4 wire, 50 Hz AC supply system having bus bar chamber with insulated aluminium bus bars four pole installed on porcelain/SMC insulator. The panel shall be dust and vermin proof IP-54 class protection and outer shell made of of 3.15 mm CRCA MS sheet, inner shell made of 2.0 mm thick CRCA MS sheet , 50x50x6mm thick MS angle iron frame work, the cubical have bottom channel of size 75x40mm duly coated with zink metal coating,front and rear opening type, with apron for cable entry closing locking arrangement including internal wiring with PVC insulated solid, copper conductor FRLS cable, IS-694 marked, 1100 volts grade of appropriate size ( but not less than 2.5 Sqmm) and comprising of the following :-

(a) Incoming :- (i) MCCB 4 pole , 400 Amps,50 Hz,415 Volts, 36 KA, with thermal magnetic release - 01 Nos (ii) On load change over switch open execution type , 315 Amps , 4 pole , 415 volt , 50 Hz-01 No (iii) Digital VAF+PF meter with RS 485 CL1 -01No (iv) CTs ratio 400/5 A ,class 1, ISI marked -01 sets of three (v) Indicating lamp- 01 set of three (vi) Four Pole , Aluminium bus bar 800 Amps insulated with colour coded heat shrinkable sleeve and shall be mounted on suitable size “F” class insulators. (b) Outgoing (i) MCCB 4 pole , 125 Amps,50 Hz,415 Volts, 25 KA thermal magnetic release - 01 Nos (ii) MCCB 4 pole , 200 Amps,50 Hz,415 Volts, 25 KA thermal magnetic release - 03 Nos

Yaduvanshi Traders (BID ID -3275601)

M/S S.B. Singh and Sons (BID ID -3279289)

Eco Creations (BID ID -3273133)

NEXT POWER ENTERPRISES (BID ID -3274649)

OM NAMAH SHIVAY ENTERPRISES (BID ID -3275222)

Joy Dey Enterprises (BID ID -3279345)

Hindustan Power Corporation (BID ID -3278946)

M/S BHAGIRATHI ENTERPRISES (BID ID -3275468)

M I & CO. (BID ID -3274827)