REPAIR/ RECTIFICATION OF DAY TO DAY COMPLAINTS OF EXTERNAL WATER SUPPLY SYSTEM INCLUDING REPAIR/ REPLACEMENT OF CI/ DI/ GI/ PPR PIPE LINE NETWORK, SLUICE VALVES, VALVE PIT CHAMBERS AND CONNECTED WORKS AT MH, ECHS, MEDOWS LINE 125 TA BN, STN WORKSHOP,

Amount

Core cutting / drilling of Bldg Roof / Wall for passing of GI Pipe up to 40 mm dia including necessary machineries complete all as specified and directed

Dismantling and strip opening the centrifugal/ Monoblock pump including disconnecting the suction, delivery, vacuum pipe lines and coupling for repairs to pump and refixing the same after repairs including overhauling the pump set, renewal of gasket to pump suction and delivery lines, gland packing, greasing nuts, bolts and washers, Metal Sleeves, painting, all kind of grinding & welding work, replacement of bearing, etc as required for arresting any kind of water leakages including testing and commissioning complete all as specified and directed for the following capacities as mentioned below :

Pump 3 phase 200 to 220 HP capacity.

Pump 3 phase 150 to 180 HP capacity.

Note: (i) The rate considered is inclusive of tools and plants including transportation of pump set from site to workshop and back required for carrying out the repairs. (ii) The rate considered is inclusive of cost towards miscellaneous items such as cotton waste, grease, Gland packing, nut bolts, all kind of grinding, welding work, gasket and other minor consumables. The cost of other spares for pump measured and paid separately under appropriate items. (iii) The rate considered is inclusive of checking of alignment of pump with dial gauge after refitting. (iv) The cost of spares for pump not mentioned above will be considered separately under appropriate items.

Dismantling and strip opening the centrifugal motor including disconnecting the cable connections and coupling of the motor, removing the starter and rotor units, bearings, servicing the motor assembly including cleaning the carbon deposits with carbon tetra chloride, greasing the bearings etc, heat varnishing the motor windings by applying varnish and keeping the windings into the hot air oven till the moisture evaporates completely at authorized workshop and refixing the same after repairs including connecting up of the electric connections including testing and commissioning complete all as specified for the following capacities :-

Motor 3 Phase 200 to 220HP capacity.

Motor 3 Phase 150 to 180 HP capacity.

Notes for item Nos 3.01 to 3.06:- (i) The rate considered is inclusive of tools and plants including transportation of motor from site to workshop and back required for carrying out the repairs. (ii) The rate considered is inclusive of cost towards miscellaneous items such as cotton waste, grease and other consumables. (iii) The rate considered is inclusive of checking of alignment of pump with dial gauge after refitting. (iv) The cost of spares for motor shall be paid separately under appropriate items.

M&L in replacement for rewinding the centrifugal/ Monoblock electric motor starter or rotor with PVC insulated, super enamelled copper conductor with ‘F’ class heavy grade insulation weight and turns to achieve its full efficiency including tying the winding and connecting the coils and brining the connections as that of existing one including applying insulating varnish, heating and backing the windings thoroughly including taking down old existing copper winding complete all as specified and directed of following capacities :- NOTE : Quoted rates inclusive of dismantling, refixing and transportation

Stator winding of Electric motor, 3 phase,180 to 220 HP capacity.

Supply only the following spares suitable for make existing at site of pump 2 stage 70 LPS capacity for repairs complete all as specified and directed :-

Pump shaft suitable for 2 stage impeller of capacity 70 LPS.

Cast Iron impeller Ist stage suitable for 70 LPS pump

Cast Iron impeller IInd stage suitable for 70 LPS pump.

Cast Iron bearing cover for drive and non drive end for pump of capacity 70 LPS

Cast iron inter stage ring for pump of capacity 70 LPS.

Rubber for water reflector for pump

Cast Iron shaft sleeve for drive end for pump of capacity 70 LPS.

Cast Iron shaft sleeve for non drive end for pump of capacity 70 LPS..

Cast Iron spacer sleeve for drive end for pump of capacity 70 LPS.

Cast Iron spacer sleeve for non drive end for pump of capacity 70 LPS..

Lock nut round type for pump of capacity 70 LPS.

Bronze nut for shaft sleeve for pump

Stuffing box bush cast Iron for pump

Gland packing for pump of capacity 70 LPS.

Set of key for pump set

Set of ‘O’ ring for pumps

Set of gaskets 3.0mm thick as per sample set of ‘O’ ring for pumps.

Cast iron gland set of 2 halves for pump of capacity 70 LPS Make of Pumps & Motors for item Nos: 6.01 to 6.18

Supply only the spare part of Non Drive End Bearing suitable for make of motor existing at site as in repairs for the following capacities of motors complete all as specified and directed :-

Motor, 3 phase, capacity 200 to 220 HP.

Motor, 3 phase, capacity 150 HP to 180 HP.

Supply only the spare part of Drive End Bearing suitable for make of motor existing at site for repairs of the following capacities of motors complete all as specified and directed :-

Motor, 3 phase, capacity 200 to 220 HP.

Motor, 3 phase, capacity 150 HP to 180 HP.

Supply only the ball bearing/ roller bearing (For Non-Drive End) suitable for make of pump existing at site for repairs of the following capacities of pumps complete all as specified and directed :-

Pump, fitted with 3 phase motor of capacity 200 to 220 HP.

Pump fitted with 3 phase motor of capacity 150 to 180 HP.

Supply only the ball bearing/ roller bearing (For Drive End) suitable for make of pump existing at site for repairs of the following capacities of pumps complete all as specified and directed :-

Pump, fitted with 3 phase motor of capacity 200 to 220 HP.

Pump fitted with 3 phase motor of capacity 150 to 180 HP.

Supply and fix in replacement of thermal overload relay with built in single phase prevention (CT Operated), 3 phase of capacity 180-300 Amps suitable for 3 phase star delta starter, type MN12, 440 volts with necessary fixing materials including disconnecting and removing the old existing one complete all as specified and directed. Make :- L&T Cat No : SS94139OOQO or equivalent make in Siemens / LeGrand

Supply and fix in replacement of electronic timer switch ST 100, 240/ 360/ 415 volts, Range 3 to 30 sec with mounting kit suitable for old existing ET 100 replacement complete all as specified and directed.

S&F in replacement power contactor with coil voltage of 440 volts, 50 cycle confirming to IS, 225 / 300 Amps, 3 pole, type MNX-225 with necessary inter connections suitable for 180 to 220 HP electric motor, testing and commissioning including removing the old existing one complete all as specified and directed.

S&F for spare contact kit of voltage of 440 volts, 50 cycle conforming to IS, 200 to 250 Amps, 3 pole, type MNX 225 / MNX 250 OF l&t with kit necessary inter connections suitable for200 HP electric motor, testing and commissioning including removing the old existing one complete all as specified and directed. Make : L&T or equivalent make in Siemens / LeGrand

S&F for spare coil for power contactor of 440 volts, 50 cycle confirming to IS, 200 to 250 Amps rating suitable for 40 HP to 220 HP electric motor, type MNX 250/ MNX300 testing and commissioning including removing the old existing one complete all as specified and directed

Supply and fix in replacement of Copper cable lugs of size 120 to 150 sq mm complete all as specified and directed :-

S&F for replacement of carbon brush suitable for Electric motor of capacity 150 -220 HP complete all as specified and directed :-

Complete removal of existing treatment including preparation of old painted surfaces by washing, rubbing down and stopping of painted surfaces, painting with one coat of synthetic enamel paint of approved colour on centrifugal pump set of 180 HP to 220 HP capacity including inlet, outlet mains, couplings, sluice valve, non return valve, base plate, pulley with safe guard, vacuum pipe line, LT panel board and writing the MES / SM number with black paint of suitable size of letters complete all as specified and directed.

Supply and replace coupling including rubber / belt of 150 HP to 220 Hp motor including necessary arrangements complete all as specified and directed. Note : Quoted rates inclusive all arrangements required for replacement of Coupling

Material and labour for detachable Coupling cover of safety of operator for 180 HP to 220 HP motor made out of 2 MM thick CRCA sheet duly painted of length 1.1 m and width 30 CM including necessary arrangement for fixing at Base frame by using Nut and Bolts . Note : Quoted rates inclusive all arrangements required for fixing the protection cover

Supply and replace Unserviceable pressure gauge stainless steel of pressure range 100 PSI Suitable for 70 LPS Pumps complete including necessary arrangements including supporting pipes complete all as directed Note : Quoted rates inclusive all arrangements required for replacement of Pressure Guage

Servicing / periodical checking of Starter panel board suitable for 180 HP to 220 HP Motor by replacing all unserviceable parts, checking for any kind of loose contact, identification of fault etc complete all as specified and directed . Note : All spare to be replaced and measured under relevant items.

Supply and fix in replacement of HDPE pipe of 65 mm bore suitable for bore well for pressure PN 16 including connection and fitting.

Supply and fix in replacement of end nipple of HDPE pipe 65mm bore suitable for bore well.

Supply and fix in replacement of end nipple of HDPE pipe 50mm bore suitable for bore well.

Repair/ rectification of leakages to water supply distribution lines 15 mm bore to 25 mm bore GI/ PPR tubing with provision of necessary excavation, cutting of hard standing, returning and filling in as required, tightening of loose joints of union, elbow, sockets etc, threading if required including replacement of GI unions/ sockets/ nipples as required at site complete all as specified and directed.

All as per item No 25.00 above but for GI tubing 40 mm bore to 50 mm bore

All as per item No 25.00 here-in-before but for GI tubing 80 mm bore to 100 mm bore.

Attending routine complaints of external water supply including rectification of minor defects by taking down of existing GI/ PPR tubing up to 25 mm bore, cutting/ threading and making joints and cleaning for any blockages, opening of float valve of service tanks, cleaning and fixing the same in its position, replacement of jumper valve/ packing sheet of gate valve and including replacement of GI unions/ sockets/ nipples etc as required at site complete all as specified and directed.

All as per item No 28.00 above but for GI tubing 40 mm bore to 50 mm bore.

Attending complaints of BLOCKAGE OF WATER PIPE LINES / NO WATER SUPPLY AT ANY kind of ACCOMODATION (MARRIED / OTM/ single / multi story building), IDENTIFY THE FAULTS including rectification by taking down of existing GI/ PPR tubing up to 80 mm bore, cutting/ threading and making joints and cleaning for any blockages, opening of float valve of service tanks, cleaning and fixing the same in its position, replacement of valve/ packing sheet of gate valve and including replacement of GI unions/ sockets/ nipples etc as required at site TO RESTORE WATER SUPPLY complete all as specified and directed.

Notes for Sl item No 30.00:- (a) The contractor will be allotted complaints at MES complaint cell on requirement basis on all working days including Sundays and holidays and sufficient tradesman / resources will be deployed by him/ her for completion of day to day complaints within 12 hours from the time of reporting. Any delay beyond above mentioned time limit without intimation of genuine cause, penalties will be recovered twice of the quoted rate for each un-attended complaint. (b) A detailed log book of complaints with completion/ non-completion remarks from users/ MES will be maintained by the contractor and the same will be updated on daily basis in consultation with JE E&M/ Engr-in-Charge. (c) The contractor will make suitable arrangement for emergency complaints and will notify authorised representee/ Engr-in-Charge about extraordinary circumstances for probable non-completion or delay in rectification of complaints beyond stated time limit set for disposal of complaint. In case of any dispute the decision of accepting officer will be final and binding in this regard.

(d) The contractor will intimate MES authority well in advance if electric shutdown is required during rectification of complaints. (e) The quoted rate is deemed to be inclusive of transportation and other expenses required for the resource deployment at the complaint site around scattered Military station at Secunderabad. (f) The contractor will maintain location wise record of each spare/ fittings utilized as per inventory format given by AGE E/ M, Secunderabad and the same shall be submitted to E/ M No II store yard on requirement basis. (g) The stationery required for the job work such as complaint slip books, gate pass book, job card and T&P shall be arranged and maintained by the contractor. (h) The cost of excavation / earth work above 1 CUM measured and paid separately under relevant items . j) Contractor is responsible for repair/ replacement of any damages to the existing structures, Under Ground HT/ LT/ OFC Cables etc during the course of execution. (k) Spares/ GI fittings required to be replaced and shall be measured and paid separately under respective items.

Rectification of leakages in pumping / delivery lines(CI/ DI/ PPR/ MS) of size 80 mm to 100 mm at Military area / Military Roads / civil Roads / PWD Roads / Cantt board roads by taking necessary permission from respective authorities by excavating PCC/ RCC/ pavement/ soft&hard soil/ rock of any depth by using necessary T&P(Excavator/ hammer drill)as per the requirement, De-watering from the trenches by using pump sets, rectification of leakages, fixing of CI/ DI specials such as collars, bends/ tail paesani type of gasket, welding work etc as required to arrest the leakages completely and making joints, filling the trenches, site clearances and PCC at the top portion as required complete all as specified and as directed. Note:- (i)CI specials, lead Joints, D-Joints, Clamp joints, DI/ CI Pipe etc shall be measured and paid under respective items of sch 'A'. (ii) Excavation and PCC will be measured and paid separately under relevant items. (iii) rate of any kind of gasket and Lead joint, necessary barrication for safety of worker etc as required, deemed to be included in the quoted rate. (iii) rate of any kind of gasket and necessary barrication for safety of worker etc as required, deemed to be included in the quoted rate. (iv) The contractor is responsible for obtaining the approval from Police Department for Traffic Diversion and related works if required in consultation with the MES department if required. (v) Contractor is responsible for repair/ replacement of any damages to the existing structures, Under Ground HT/ LT/ OFC Cables etc during the course of execution.

Rectification of leakages in pumping / delivery lines(MS/ CI/ DI/ PPR) of size 150 mm to 450 mm at Military area / Military Roads / civil Roads / PWD Roads / Cantt board roads by taking necessary permission from respective authorities by excavating PCC/ RCC/ pavement/ soft&hard soil/ rock of any depth by using necessary T&P(Excavator/ hammer drill)as per the requirement, De-watering from the trenches by using pump sets, rectification of leakages, fixing of CI/ DI specials such as collars, bends/ tail paesani type of gasket, welding work etc as required to arrest the leakages completely and making joints, filling the trenches, site clearances and PCC at the top portion as required complete all as specified and as directed. Note:- (i)CI specials, lead Joints, D-Joints, Clamp joints, DI/ CI Pipe etc shall be measured and paid under respective items of sch 'A'. (ii) Excavation exceeding 2 CUM and PCC will be measured and paid separately under relevant items. (iii) rate of any kind of gasket and necessary barrication for safety of worker etc as required, deemed to be included in the quoted rate. (iv) The contractor is responsible for obtaining the approval from Police Department for Traffic Diversion and related works if required in consultation with the MES department if required. (v) Contractor is responsible for repair/ replacement of any damages to the existing structures, Under Ground HT/ LT/ OFC Cables etc during the course of execution.

M&L for attending break down of water supply pipe line at Military area / Military Roads / civil Roads / PWD Roads / Cantt board roads and repair s to CI/ DI/ PPR/ MS water mains of size 80 mm to 300 mm bore at a given notice including necessary excavation in mud, in any type of soil, PCC,RCC, hard rock etc by manual or using special T&P such as JCB etc. De-watering from the trenches by using pump sets, rectification of leakages, fixing of CI specials such as collars, bends/ tail peaces etc and making joints complete all as specified and as directed including making good of disturbed surfaces. Note:- (i)CI specials, lead Joints, D-Joints, Clamp joints, DI/ CI Pipe etc shall be measured and paid under respective items of sch 'A'. (ii) Excavation and PCC will be measured and paid separately under relevant items. (iii) rate of any kind of gasket and necessary barrication for safety of worker etc as required, deemed to be included in the quoted rate. (iv) The contractor is responsible for obtaining the approval from Police Department for Traffic Diversion and related works if required in consultation with the MES department if required. (v) Contractor is responsible for repair/ replacement of any damages to the existing structures, Under Ground HT/ LT/ OFC Cables etc during the course of execution.

Excavation in trenches not exceeding 1.5 m width and not exc 1.5 m in depth and getting out in hard/ dense soil for removing/ laying of pipe line complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in any type of soil complete all as specified and directed.

Removing excavated material (soils) n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed.

Taking up or down steel tubing and connections, including cleaning the pipes free from scaling for re-fixing or removal complete with all fittings and connections of the following sizes :-

15 mm dia

20 mm dia

25 mm dia

40 mm dia

50 mm dia

80 mm dia

Refixing of old steel tubing and connection in new or old position including cutting threads if required, fittings with old/ new bends, elbows, socket, nipple, tapers, and reducers etc as per site requirement and laid in trenches and testing for leakages complete all as specified and directed for the following sizes:- Note: (a) Excavation and Earth work shall be measured and paid separately.

15 mm dia

20 mm dia

25 mm dia

40 mm dia

50 mm dia

80 mm dia

Refixing of old steel tubing and connection in new or old position including, cutting threads if required, fittings with old/ new bends, elbows, socket, nipple, tapers, and reducers etc as per site requirement and laid in floors, walls and ceilings and testing for leakages complete all as specified and directed for the following sizes:-

15 mm dia

20 mm dia

25 mm dia

40 mm dia

50 mm dia

Supply and laying in replacement steel water tubing medium grade, galvanised with all fitting, laid in trenches and testing for leakages complete all as specified and directed for the following sizes:- Note: (a) Excavation and Earth work shall be measured and paid separately.

15 mm dia

20 mm dia

25 mm dia

40 mm dia

50 mm dia

80 mm dia

Supply and laying in replacement steel water tubing medium grade, galvanised with all fitting, fixed to wall and ceilings or laid in floor and testing for leakages complete all as specified and directed for the following sizes:-

15 mm dia

20 mm dia

25 mm dia

40 mm dia

50 mm dia

Taking up or down PPR pipe and connections, including cleaning the pipes free from scaling for re-fixing or removal complete with all fittings and connections of the following sizes :-

32 mm dia

63 mm dia

Refixing of old PPR Pipe and connection in new or old position including fittings with old/ new bends, elbows, socket, nipple, tapers, and reducers etc as per site requirement and laid in trenches and testing for leakages complete all as specified and directed for the following sizes:- Note: (a) Excavation and Earth work shall be measured and paid separately.

32 mm dia

63 mm dia

Refixing of old PPR Pipe and connection in new or old position including fittings with old/ new bends, elbows, socket, nipple, tapers, and reducers etc as per site requirement and laid in floors, walls and ceilings and testing for leakages complete all as specified and directed for the following sizes:-

32 mm dia

63 mm dia

Supply, laying replacement and testing of polypropylene random copolymer (PP-R) (PN-10-SDR-11) 3 layer pipes ISI marked as per IS-15801, UV stabilized and anti microbial fusion welded having thermal stability for hot and cold water supply all PPR plain and brass thread polypropylene random fittings laid in trenches of following sizes including all fittings. Make : SFMC/ WETFLOW/ SAFE. Note: (a) Excavation and Earth work shall be measured and paid separately.

32 mm dia

63 mm dia

Supply, laying and testing of polypropylene random copolymer (PP-R) (PN-10-SDR-11) 3 layer pipes ISI marked as per IS-15801, UV stabilized and anti microbial fusion welded having thermal stability for hot and cold water supply all PPR plain and brass thread polypropylene random fittings fixed complete to walls, ceilings or in floors etc of following sizes including all fittings. Make : SFMC/ WETFLOW/ SAFE.

32 mm dia

63 mm dia

Taking up unserviceable/ defective CI/ DI/ MS/ PPR water mains (including all fitting) with spigot/ socketed / flanged ends including disconnecting pipes and fittings in any position complete all as specified and directed for the following sizes:-

80 mm Dia

100 mm Dia

150mm Dia

200 mm Dia

250 mm Dia

300 mm Dia

Refixing and replacement of old CI/ DI/ MS Pipe and connection in new or old position including fittings with old/ new bends, elbows, socket, nipple, tapers, and reducers etc as per site requirement and laid in trenches and testing for leakages complete all as specified and directed for the following sizes:- Note: (a) Excavation and Earth work shall be measured and paid separately.

80 mm dia

100 mm dia

150 mm dia

200 mm dia

250 mm dia

300 mm dia

S&F in replacement of ductile iron pressure pipes, class K7, centrifugally cast with spigot and socket ends as per following conforming to IS 8329/ 2000 with cement mortar lining inside the pipes with outside zinc coating suitable for push-on-joint (rubber gasket D jointing) in any length including DI specials as required at site confirming to IS 8329/ 2000 and all jointing materials and making good for disturbed surfaces of roads, path ways etc while laying the pipe line at site, site clearance for the route of pipe line, welding, cutting the existing CI/ DI/ MS pipe line of any size up to 400 mm dia for inserting branch connections etc complete all as specified and directed for the following sizes:- Notes:- (a) Quoted rates inclusive of Push on Joints / D-Joints as required (b) The contractor is responsible for obtaining the approval from Police Department for Traffic Diversion and related works if required in consultation with the MES department if required. (c) Contractor is responsible for repair/ replacement of any damages to the existing structures, Under Ground HT/ LT/ OFC Cables etc during the course of execution. (d) Excavation and Earth work shall be measured and paid separately.

100 mm Dia

150 mm Dia

200 mm Dia

300 mm dia

400 mm dia

Cutting existing CI pipe line for insertion of new tees, collars for branch connections complete all as specified and directed for the following sizes:- Note: CI / DI specials, Joints and Earth work shall be measured and paid separately under relevant items of this schedule.

80 mm Dia

100 mm Dia

150 mm Dia

200 mm Dia

300 mm Dia

Supply only GI fittings 15 mm bore, medium grade, ISI marked, smooth finished and make embossed on fittings complete all as specified and directed for the following fittings:-

Union

All equal Tee

Socket

Nipple 75mm Long

Nipple 100mm Long

Nipple 150mm Long

Elbow

Hex Nipple

All as per item No 51.00 above but for 20 mm bore.

Union

All equal Tee

Reducer Tee 20 x 20 x 15 mm

Socket

Reducer Socket 20 x 15 mm

Nipple 75mm Long

Nipple 100mm Long

Nipple 150mm Long

Reducer Elbow 20 x 15 mm

Elbow

Hex Nipple

All as per item No 51.00 above but for 25 mm bore.

Union

All equal Tee

Socket

Reducer Socket 25 x 20 mm

Reducer Socket 25 x 15 mm

Nipple 75mm Long

Nipple 100mm Long

Nipple 150mm Long

Elbow

Reducer Elbow 25 x 20 mm

Reducer Elbow 25 x 15 mm

Reducer tee 25mm x 25 mm x 20mm

Reducer tee 25mm x 25 mm x 15mm

Hex Nipple

All as per item No 51.00 above but for 40 mm bore.

Union

All equal Tee

Socket

Reducer Socket 40mm x 25 mm

Nipple 75mm Long

Nipple 100mm Long

Nipple 150mm Long

Elbow

Reducer elbow 40mm x 25mm

Reducer tee 40mm x 40mm x 25mm

Reducer tee 40mm x 40mm x 20mm

Hex Nipple

Reducer Socket 40mm x 20 mm

Reducer elbow 40mm x 20mm

All as per item No 51.00 above but for 50 mm bore.

Union

All equal Tee

Socket

Nipple 75mm Long

Nipple 100mm Long

Nipple 150mm Long

Reducer Socket 50mm x 40mm.

Reducer Socket 50mm x 25mm.

Elbow

Reducer elbow 50mm x 40mm

Reducer elbow 50mm x 25mm

Reducer tee 50mm x 50 mm x 40mm

Reducer tee 50mm x 50 mm x 25mm

Reducer tee 50mm x 50 mm x 20mm

Hex Nipple

All as per item No 51.00 above but for 80 mm bore.

Union

All equal Tee

Socket

Reducer Socket 80mm x 50mm.

Reducer Socket 80mm x 40mm.

Nipple 75mm Long

Nipple 100mm Long

Nipple 150mm Long

Elbow

Reducer elbow 80mm x 50mm

Reducer elbow 80mm x 40mm

Reducer tee 80mm x 80mm x 50mm

Reducer tee 80mm x 80mm x 40mm

Hex Nipple

Supply and fix in replacement of unserviceable Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipes and fixed complete all as specified and directed for the following sizes:-

20mm dia bore

25mm dia bore

40mm dia bore

50mm dia bore

Supply and fix in replacement of unserviceable ball brass valves, high pressure with polythene float and flynut alongwith socket/ reducer of suitable size, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed for the following sizes:-

20mm dia bore

25mm dia bore

M&L in replacement for Arresting leakages of sluice valves by replacing Gland packing, gland bush, gland falange, nutbolts, gasket, packing material as required after dismantling in existing position including testing on completion complete all as specified and directed for the following sizes:- Note: Quoted rates inclusive of the materials mentioned above like Gland packing, gland bush, gland falange, nutbolts, gasket, packing material etc as required to arrest the leakages.

80 mm Dia

100 mm Dia

150 mm Dia

200 mm Dia

250 mm Dia

300 mm Dia

400-450 mm Dia

S&F in replacement of CI / DI specials such as bends (any type, radius or angle) tapers any type (Straight, bend, increase, decrease or double socket etc) tee pieces, single 'Y' branch, double branch cross (all sockets, socket and spigots, collars, cap plugs etc up to 150 mm bore complete all as specified and directed.

All as per item No 60.00 above but for 200 mm bore to 300 mm bore.

Burning out lead joint in position for following sizes of CI/ DI pipe, removing old lead complete all as specified and directed :-

80 mm Dia

100 mm Dia

150 mm Dia

200 mm Dia

250 mm Dia

300 mm Dia

400 mm Dia

M&L for run lead joint for CI pipe/ DI pipe including spun yarn etc for spigot and socket pipes and fittings complete all as specified and directed for the following bore of pipes:-

80 mm Dia

100 mm Dia

150 mm Dia

200 mm Dia

250 mm Dia

300 mm Dia

S&F in repairs and replacement of CAST IRON OR DUCTILE IRON MECHANICAL COUPLING / MECHANICAL JOINT / D JOINT heavy duty INCLUDING ALL JOINTING MATERIAL, ISI marked, split type with long collar, suitable rubber rings, bolts, nuts and washers etc suitable for MS/ CI/ DI/ GI / PVC pipes of following sizes AS REQUIRED FOR REPAIRING OF ANY KIND OF LEAKAGES COMPLETE all as specified and as directed:- Notes:- (a) Excavation and Earth work shall be measured and paid separately. (b) Quoted rate inclusive of cutting of any kind of pipes and all ITEMS as required for fixing and proper functioning of Joints. (c) Quoted rate is deemed to be inclusive of necessary T&P for cutting the pipe line, Pump sets for De-watering, JCB for Excavation (if required) etc and no extra payment shall be admissible on this account.

80 mm Dia

100 mm Dia

150 mm Dia

200 mm Dia

250 mm Dia

300 mm Dia

400 mm Dia

Supply and fixing in replacement of DI D/F Gate valve (Soft Sealed) Resilient Seated Soft Sealing gate valves(Sluice valves RAISING TYPE ) with body bonnet of ductile cast iron of grade GGG-40/ SG- 400/ 15 or GGG-50/ SG-500/ 7 or equivalent grade as per IS 3896 - Part 2- 1985 and subsequent revisions, Wedge fully rubber lined with EPDM Food grade quality and Seals of NBR and the valve should be vacuum tight and 100 % leak proof with face to face dimension as per BS 5163-89/ IS 14846-2000/ DIN 3202 F 4. and Valves should be electrostatic powder coating both inside and outside pocket less body passage class PN 1.6 including all jointing materials (Gasket, Nutbolts ets) connecting and testing complete all as specified and directed.

80 mm Dia

100 mm Dia

150 mm Dia

200 mm Dia

300 mm Dia

Supply and fix in replacement NRV including making provisions in existing pipeline of DI/ MS of the following sizes completed all as directed. Note : Quoted rates inclusive of all arrangement required for the above

150 mm Dia

200 mm Dia

S&F in replacement of Cast Iron sluice valves flanged ends stem of SS (AISI410) & Bronze (Gun Metal) working parts IS : 14846 both ends flanged with clamps and check nuts, operating wheel etc, rising type K506, class PN 1.6 including jointing materials connecting and testing complete all as specified and directed.

150 mm Dia

200 mm Dia

300 mm Dia

S&F in connecting and testing in replacement, of Cast Iron non return (Reflux) valves flanged ends in swing type design IS-5312 part-I, K517, PN-1.6 both ends flanged etc including jointing materials of following sizes complete all as specified and directed.

65 mm Dia

150 mm Dia

S&F in replacement, connecting and testing in repair of Cast Iron foot Valves flanged ends swing type operation with rubber seat as per IS : 4038 single disc with all standard accessories and tested including replacement of nuts, bolts, washers, gaskets, packings etc complete all as specified and directed.

50 mm Dia

65 mm Dia

100 mm Dia

S&F in replacement, connecting and testing in repair of Cast Iron double orifice kinetic Air Valve ISI Marked IS : 14845 type DK in PN 1.0 flanged end K541 with all standard accessories and tested including replacement of nuts, bolts, washers, gaskets, packings etc complete all as per specified and directed.

80 mm Dia

100 mm Dia

150 mm Dia

Cutting the existing road straight by manual, depth and width not less than 30 cm for pipes up to 100 mm dia and 60 cm for pipes from 150 mm to 150 mm dia and 75 cm for pipes above 250 mm dia and filling back with excavated soil up to 75 % road portion and 25 % shall be made with cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate complete all as specified and directed.

M&L for Construction of new PCC solid Masonry valve chamber of size 1500 X 1500 X 1500 mm (Internal dimensions) with PCC foundation 1:4:8 type D2 using 40 mm graded stone aggregate 150 mm thick 150 mm wide off sets around over 100 mm thick hard core, 200 mm thick PCC solid block walls built in CM 1:6, 50 mm thick PCC 1:2:4 Type B1 coping finished even and smooth, rendering 10 mm thick in cement mortar (1:6) finished even and smooth, with out using extra cement internally including top of floor including excavation earth work in hard/ Dense soil 3 mm thick MS sheet cover fixed on 40 mm X 40 mm X 6 mm thick angle iron frame with hold fasts embedded in PCC coping with locking arrangement, mild steel handle and painting to steel surfaces with two coats of synthetic enamel paint over one coat of primer including disposal of surplus soil to a distance not exceeding 50 m etc complete all as specified and directed.

Supply and fixing in replacement of SFMC PP-R Pipe fittings and accessories 32 mm bore, smooth finished and make embossed on fittings complete all as specified and directed for the following fittings:-

Reducer Socket 32 x 25 mm

Socket

All equal Tee

Union

Gate Valve

All as item No 73.00 above but 63 mm bore :-

Reducer Socket 63 x 32 mm

Socket

All equal Tee

Reducer Tee 63 x 63 x 32 mm

Union

Gate Valve

M&L for replacement of cross arms, bracings, supports, clamps and back plates fabricated from structural steel sections including welding, bending cold or hot, drilling holes for hinged, in any shape or size as indicated for valve chamber top cover, 4 mm thick MS sheet cover fixed on 40 mm X 40 mm X 6 mm thick angle iron frame with locking arrangement, mild steel handle, and painting to steel surfaces with two coats of synthetic enamel paint over one coat of primer including disposal of surplus soil to a distance not exceeding 50 m etc complete all as specified and directed.

M&L for road crossing/ drain crossing by adopting trench less tunnelling work through specified pipe jacking method by erecting the equipment to true to the alignment and gradient by haidrolic pipe jacking technique complete including tunnelling, excavation in any type of soils including hard rock, TO CROSS WATER PIPE LINE UP TO 200 mm dia in any length including jointing materials and necessary conveyance charges of machinery and other required materials in co-ordination with the concerned authorites complete all as specified and as directed INCLUDING MAKING GOOD OF DISTURBED SURFACES. NOTE: PIPE WILL BE MEASURED AND PAID SEPARATELY 8UNDER RELIVENT ITEMS

M&L PCC 1:3:6 type C1 using 20 mm graded stone aggregate for coping & plastering of valve chamber complete all as directed

M&L PCC 1:2:4 type B1 using 20 mm graded stone aggregate for FILLING / FOOTHPATH/ ROAD complete all as directed

S&F in replacement water level Indicator and controller with the feature mentioned here under:- 1. S& F Transceiver must communicate at a distance of 3km -5kms range with each module must have the GSM or suitable communication module (long range antenna) must work above 500 MHz and each module shall have a processor module connecting to the sensor, with the facility that the processor module to sense the low level (10-20%) and high level of the water level (90-100%) so as to raise the hooter and communicate with the other hardware modules with antennas. S&F transducer module with magnetic float sensors, wiring through the 6/ 8 core cables. All the wiring must be 6/ 8 core cables cable for connection to flasher and hooter. Rates quoted are deemed to be included for suitable flasher and hooter. S&F Hooter 12V with suitable converter or hooter suitable for 230V AC Supply must be provided standard suspended rust proof stand S &F of LED display board with superior night vision display to be provided at the receiver station. All the 3D/ CAD models must be provided for review before the enclosure are fitted with AUTO CAD/ PRO drawings shall be provided. Note: Complete system shall be warrantied with 24 hrs rectification for any non functioning for a period of 1 year replacement warranty. (a) One transmitter for over Head Tank and one receiver for Pump Ho

M&L for painting of water distribution header including all control valves and all exposed pipe of any size by using synthetic enamelled spray painting after scrapping / cleaning complete all as directed .

Repairing of Sluice valves raising / non raising types after dismantling the same by replacing stem, gate/ disc, stuffing box, Seat, Gland packing, gland bush, gland falange, nutbolts, gasket, packing material, threading, welding as required for proper functioning of Sluice valves complete all as directed. Note: Quoted rates inclusive of all the materials mentioned above like stem, gate/ disc , Seat stuffing box Gland packing, gland bush, gland falange, nutbolts, gasket, packing material etc as required for proper functioning of the valves

80 mm Dia

100 mm Dia

150 mm Dia

200 mm Dia

250 mm Dia

300 mm Dia

Supply and lay in replacement of Pipes MS black ERW Steel including specials having nominal dia 100 mm of thickness 6.0 mm as per IS 3589 - 2001, Grade - 330 with plain ends and specials by welding, leak testing of line laid in trenches / floors/ walls / ducts complete all as specified and directed. Note: Quoted rate is inclusive of supply and fixing of flange of suitable size as required, bends welding and cutting etc as required for fixing of pipe .

Supply and lay Pipes in replacement of MS black ERW Steel including specials having nominal dia 150 mm of thickness 6.0 mm as per IS 3589 - 2001, Grade - 330 with plain ends and specials by welding, leak testing of line laid in trenches / floors/ walls / ducts complete all as specified and directed. Note: Quoted rate is inclusive of supply and fixing of flange of suitable size as required , bends, welding and cutting etc as required for fixing of pipe .

Supply and lay in replacement of MS black tubing ERW welded including specials, having outside dia of 212 mm and 6 mm thick ISI marked conforming to IS 3589 - 2001 with plain ends complete including connecting of MS pipes and specials by welding, leak testing of pipe line laid in trenches / floors / walls / ducts complete all as specified and as directed by the Engineer-in-charge. Note: Quoted rate is inclusive of supply and fixing of flange of suitable size, bends as required, welding and cutting etc as required for fixing of pipe .

Supply and lay in replacement MS black tubing ERW welded, having outside dia of 314 mm and 7 mm thick ISI marked conforming to IS 3589 - 2001 with plain ends complete including connecting of MS pipes and specials by welding, leak testing of pipe line laid in trenches / floors / walls / ducts complete all as specified and as directed by the Engineer-in-charge. Note: Quoted rate is inclusive of supply and fixing of flange and bends of suitable size as required, welding and cutting etc as required for fixing of pipe .

MS ENTERPRISES (BID ID -3500296)

Haasith constructions (BID ID -3500166)

sree venkateswara enterprises (BID ID -3494748)

sandhya enterprises (BID ID -3507147)