REPAIRS TO PLASTERING JOINERY FLOORING FALSE CEILING SANITARY FITTINGS FOR CERTAIN DOM ASC HOUSE DCCI HOUSE ASC RECORDS OF NO2 ATC SOUTH UNDER AGE B AND R II OF GE CENTRAL BANGALORE

Amount

Taking down cement plaster of any description including racking out joints, hacking for key scrubbing down with water etcand removal of entire debris as ordered outside MD land complete all as directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc and removal of debris to a distance not exceeding 50 mts and depositing where directed.

Dismantling floor, hearth or wall tiling inluding cement mortar bedding (but including backing), stacking serviceable tiles at site and removal of entire debris as ordered outside MOD land complete all as directed.

Taking down chowkats or frames not exc 1.5 sqm each with shutters (without taking off shutters from frame) and stacking at site where directed.

Taking down chowkats or frames exc 1.5 sqm & not exceeding 4 Sqm each with shutters (without taking off shutters from frame) and stacking at site where directed.

Taking down shutter of any description area exceeding 1 Sqm but not exceeding 2 Sqm each and refixing in the same opening after cutting , easing and adjustmentas with old ll types of builders hardware complete all as directed.

Taking down shutter of any description exceeding 1 Sqm but not exceeding 2 Sqm each and stacking at site where directed.

Taking down & refixing in shutters of any description exc 1 sq. m and n exc 2 sq. m each complete all as specified and directed.

Dismantling of AC Corrugated or semi corrugated sheet etc any thickness including ridges as in roof covering and stacking at site where directed and removal of entire debris as ordered outside MD land complete all as directed.

Demolition and breaking up 75/100 mm bia drain pipes (Salt glazed ware, AC or Rein-forced concrete) set in cement mortar including removal of entire debris as ordered outside MD land complete all as directed.

M & L for PCC 1 :5 : 10 type E2 using 40 mm graded crushed stone aggregate as in foundation filling, sunken repairing & mass concrete complete all as specified and directed

M&L factory made pre cast PCC 1:3:6, type C1 (using 20 mm graded granite aggregate) as in block masonry with solid blocks, exceeding 10 cm in width and setting in CM 1:6 complete all as specified.

Supply only Integral Water Proofing Compound (ISI Marked) of Make : CICO , Acco Proof , Impermo , Aqua flex as approved.

S&F factory made pressed steel frames of size 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, mild steel sheet of 1.25 mm thickness, including filling hollow chowkat frame with plain cement concrete 1:2:4 type B0 using 12.5 mm graded aggregate to the satisfaction of Engineer-in-chatge complete as specified & as directed.

All same as per item No 14 here-in-above but steel frames of size 125 x 60 mm -do-

S&F solid PVC door frame of size 50X47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube supplying and fixing in opening as per specification all as directed.

S &F 35 mm thick second class hard wood factory made glazed and skeleton shutter open rebated and prepared to receive glass, guage etc edge of framing plain chamfered or rounded fitted with cut and mitred beads for securing guage etc size of members of shutter as specified in SSR Part I Section 8 clause 8.24 (a) supplied and fitted to chowkats.

S&F 30mm thick Flush shutters, veneered solid core construction, with block coard core & plywood face panels commercial type on both side conforming to IS 2202 (Part- I) -1999, including internal liping beading all round fixed as in Door Shutter,Cup board shutter & Kitchen rack all as specified.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with plain colour single piece extruded PVC profile ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour single piece extruded PVC profile for top rail lock rail bottom rail on either side and as gap insert for Top rail and bottom rail paneling of plain colour PVC sheet to fitted on the MS frame welded/sealed to the styles and rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified and as directed..

S&F 19 mm thick MDF Board both side finished cut to size & fixed in wardrobes , number of compartments & drawers as ordred complete all as specified.

S & F150 mm long aluminium, anodised , barrel tower bolt (ISI marked) of extruded section and fixed.

S & F in repair125 mm long aluminium, anodised , barrel tower bolt (ISI marked) of extruded section and fixed.

S & F 125 mm long aluminium, anodised , barrel tower bolt (ISI marked) of extruded section and fixed.

S & F in repair 100 mm long aluminium, anodised , alloy handle (ISI marked) of extruded section and fixed.

S&F125 mm size butt hinges, medium weight cold rolled mild steel and fixed .

S&Fin repair 150 mm size butt hinges, medium weight cold rolled mild steel and fixed .

S&F 300 mm long aluminium alloy, anodised sliding door bolt (ISI Marked) with hasp, staple (bolt type) and fixing clip of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed.

S&F Brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long be-tween flanges complete all as directed including taking down old towel rail.

S&F in Repair Brass Lockers, Drawer, grade-I,size 50mm 4 levers of approved make all as directed by Engineer-in-Charge.

S&F in Repair Brass 40mm dia Cupboard Knobs fixed with nut, screw and washer, bright finished.

S&F continuous (piano) hinges, mild steel, bright finish or electro galvanized width of flaps 30mm (when open) fixed with CP steel screws complete all as specified and as directed

S&F in repair 25mm dia Aluminium powder coated curtain rods/ towel / ward robe rod etc all as specified and directed.

S&F in repair Aluminium powder coated brackets for curtain/Towel/ Ward robe hanging rodall as specified and directed.

S&F in repair 25 mm dia metalic coated curtain road complete all as specified and directed

S&F in repairs stainless steel wire cloth, 0.24mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples including supply & fix second class hard wooden fillet, wrought, cross sectional area exceeding 3 Sqcm but n.exc 6 Sqcm fixed with nails complete all as directed.

S&F stainless steel wire cloth 0.24 mm nominal dia of wire and average width of aperature 1.40mm and fixed with stainless steel wire staples including supply & fix second class hard wooden fillet, wrought , cross sectional area exceeding 3 Sqcm but n.exc 6 Sq cm fixed with nails complete all as directed.

S&F anodized aluminium frame for doors, windows, ventilators, partitions, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) with one or more rebates including joining cleat for fixing etc. complete all as specified & as directed.

S&F anodized aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodized aluminum snap beading screws etc. complete all as specified & as directed

S&F Bands, straps, supports or stays for rainwater, hold fasts; wall ties; and similar small articles steel conforming to Fe-290 Gde-E-165.

S&F mild steel framed work as in grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors and similar work including welding conforming to Grade E-165 (Fe 290), complete, all as specified & directed.

S&F in repair aluminium anodised snap grid frame work for false ceiling of grid size 605x605 mm including hangers and cleats with Perforated particle board/tiles for insula-tion andaccoustic purposes,60x60 cm in size, fixed with nails to timber frame work or with stapleson snap gridcomplete all as specified and as directed.

M&L for applying evenly two coats of blown type hot bitumen at the rate of 1.50 Kg per sqm and blinding with clean dry sand @ 0.005 cum per sqm complete all as specified & as directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or ‘L’ type or ‘J’ type or cranked hooks bolts complete all as specified & directed

Supply and fix Pre- painted galvalume aluminum zinc coating GI plain sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or L type or J type or cranked hook bolts or as per manufacture instruction all as specified and as directed.

Material and labour for removal of existing WPT course or any other kind of treatment surface over roof slab and cleaning of surface with wire brushes and water removing of unsolvent materials and depositing of the same outside MoD land and provide 10 mm thick screed bed/ bedding layer in CM 1:3 mixed with Water Proofing Compound (WPC) as per manufacturer instructions, including finishing the surface fair and even on RCC roof/ parapet once bedding layer of concrete is completely dried and apply oil bound bituminous primer @ 0.20 Kg/Sqm and providing 4mm thick APP modified water proofing membrane weighing not less than 4.00 Kg/Sqm reinforced with non woven polyster matt weighing not less than 160 gms/Sqm including minimum 10 cm side over laps and 15 cm end lap torch sealed and bonded as per detailed procedure as directed, apply a coat of blown grade hot bitumen 90/15 grade over the membrance @1.2 Kg/Sqm and finally finished the top surface with solar reflective bituminious aluminium @ 0.10 Kg/Sqm complete all as specified and as directed. Note: (i) The quoted rate is deemed to be inclusive of taking down & removal of debris , 10 mm thick 1:3 screed & complete APP treatment. (ii) WPC will be paid seperately (iii) The work shall be carried out only through manufacturer or their authorised applicator and a written guarantee for work shall be submitted by the manufacturer for the effectiveness of WPT (iv) Care shall be taken to avoid wrinkle and air gaps while sticking membrane to the bitumen applied surface.

M&L for 25 mm thick plain cement concrete 1:2:4 type B1 using 20mm graded crushed stone aggregate as in floor and finished the surface suitable to receive floor tiles complete all as directed.

M & L non-skid coloured joint free ceramic tiles 7 to 8 mm thick (square/ rectangular), area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with tiles laid over and including 15 mm thick screed bed in cement mortar 1:6 complete all directed and specified.

M&L glazed ceramic designer tiles any shade or pattern as approved of size 350x250x7mm / 450x350x7 mm thick, on verticals surfaces, set and jointed in neat cement slurry including 10 mm thick back coat in CM 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all directed. (Note for item Nos 47 & 48 : i) Quoted rate is deemed to be inclusive of cement screed. ii) Shade / pattern / Colour of tiles shall be got appproved before procurement).

M & L rendering 15 mm thick in two coat ie., 10mm thick under coat in CM 1:4 and 5 mm thick finishing coat in CM 1:4 mixed with WPC finished even & smooth without using extra cement complete all as specified and directed.

M&L for rendering 10 mm thick in CM 1:6 on brick work/ block concrete surface finished the surface even and smooth without using extra cement complete all as specified.

M&L for rendering 5 mm thick in CM 1:3 on concrete surface as in ceiling,chajja,roof projection etc. finished the surface even and smooth without using extra cement complete all as specified.

Three coats of white wash on newly plastered surface of ceilings after necessary preparation of surface complete all as directed.

M&L preparation of newly plastered wall surfaces and applying two coats of cement base paint over a coat of alkali resistant primer over a coat of 1-2 mm thick external wall care putty as ordered complete all as specified.complete all as directed.

M&L preparing new plastered wall surfaces and applying two coats of oil bound distemper over a coat of alkali resistant primer over a coat of 1-2 mm thick wall care putty as ordered complete all as specified.

Hacking out old broken glass (any thickness) and size from wooden frame glazed with putty or fixed with wooden beads and removal of debris to a distance n.exc 50 mtr and depositing where directed.

S&F sheet glass 4mm thick glazing with oil putty or wooden beads not exceeding 0.5 Sqm in each pane complete all as directed.

S&F in repairs sheet glass 4mm thick glazing with oil putty or wooden beads not exceeding 0.5 Sqm in each pane complete all as directed.

S&F sheet glass 4mm thick figured glass, pin headed type and glazing with oil putty or wooden beads not exceeding 0.5 Sqm in each pane complete all as directed.

M & L Two coats of 1st quality synthetic enemal paint over a coat of zinc chromate primer over any description of new steel surface over 10 cm in width or girth including necessary preparation of new steel surface complete all as directed.

M & L Two coats of 1st quality synthetic enamel paint over a coat of pink primer on new wooden surface of any description over 10 cm in width or girth including necessary preparation of new wooden surface complete all as directed.

Taking down old rusted / wornout 25 mm bore GI tubing after necessary disconnection & S&F new 25 mm bore CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings fixed on walls/ceiling or laying in floors making necessary connection& testing on completion complete all as directed.

Taking down old rusted / wornout 20 mm bore GI tubing after necessary disconnection & S&F new 20 mm bore CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings fixed on walls/ceiling or laying in floors making necessary connection& testing on completion complete all as directed.

S&F in repair 15 mm bore bib taps cast copper alloy with crutch or butterfly handle,screwed down complete all as specified and directed

S&F in repair 15 mm bore brass CP mixer for mixing hot & cold water screwed down for iron pipe complete all as specified and directed

S&F in repair 15 mm bore stop valves cast copper alloy with crutch or butterfly handle,screwed down fancy type complete all as specified and directed

S&F in repair 15 mm bore stop valves cast copper alloy with crutch or butterfly handle,screwed down fancy type with long shank and cup complete all as specified and directed

S&F in repair 15 mm bore push taps any colour high pressure of PTMT screwed for iron pipe and fixed (Minimum weight 15 mm-47 gms)

S&F in Repair 2 way Bib cock Double handle with flange 15mm Bore cast copper alloy chromium plated with wall flag, screwed down,screwed for pipes.( make: prayag cat no.8312 or Equivalent )

S&F in repairs brass chromium plated shower rose 125 mm dia with or wihout swivel joint, any size, including fixing to steel pipe or union.Make : Prayag or equivalent as approved.

S&F SS Soap dish holder complete all as specified and directed.

S&F in repair PVC cabinets of size 450 x 300 mm fixed to wooden plug with chromium plated brass screws & cp washer complete all as directed.

S & F in repair 110 mm bore, PVC (SWR), Type 'B', Soil waste and vent pipes in any length without ears, with rubber ring joints laid in trenches complete all as specified and directed.

S & F in repair 75 mm bore, UPVC (SWR), Type 'B', Soil waste and vent pipes in any length without ears, with rubber ring joints laid in trenches complete all as specified and directed.

S & F in repair 110 mm bore, UPVC (SWR), Type 'B', Soil waste and vent pipes or for rain water pipe in any length without ears, with rubber ring joints fixed to wall using MS holder bat complete all as specified and directed.

S & F in repair 75 mm bore, UPVC (SWR), Type 'B', Soil waste and vent pipes or for rain water pipe in any length without ears, with rubber ring joints fixed to wall using MS holder bat complete all as specified and directed.

S & F 110 mm bore, PVC (SWR) bends of any radius complete all as specified and directed.

S & F 75 mm bore, PVC (SWR) bends of any radius complete all as specified and directed.

S&F 110 mm bore PVC (SWR) junction single (single ‘T’), equal or unequal with access door

S&F 75 mm bore PVC (SWR) junction single (single ‘T’), equal or unequal with access door

S&F in repair 75 mm size PVC (SWR) floor trap with grating including jonting the same with solvent cement complete all as directed.

S&F 550 mm X 400 mm size white flat back vitreous china wash hand basin including chromium plated pillar tap cap stain head suitable for 15 mm bore of pipe , PVC connection 15 mm dia 45 cm long with chromium plated nuts and bolts and suitable washers, PVC waste 32 bore CP waste coupling chain and plug , porcelain stopper including CI bracket fixed in repair complete all as diirected.

S & F in repair Vitreous china wash down water closet pan (Pedestal pattern) white complete including plastic water closet seat cover (Black) closed pattern with flat bottom and cover and mild steel chromium plate or aluminium hinging device and 32mm dia PVC flush pipe high or low density suitable for low / high level cistern connected from flush out let to WC flushing in let. (Flushing cistern high / low measured and paid seperately).

S&F in repairs vitreous china bowl type urinal flat back, size of 465 x 355 x 265mm (minimum) white including providing & fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with & including 60 mm long brass screws, pointing around urinal back in cement, with & including PTMT grating and union for discharge pipe including waste pipe of polythelene of low or high density or PVC 32mm dia complete all as specified.

S&F in repairs brass chromium plated Hand Shower (Health Faucet) (ABS Body) mild steel chorimium plated suitable for 15 mm dia pipe with 1.25 Mts long flexible tube and ABS wall hook including making connections complete all as directed.

S&F in repair 32 mm low density polyethylene (LDPE) pipes of pressure rating 6 Kgf/Sq.cm with connecting bracket for wash basins complete all as specified and directed.

.S&F in repairs PVC valveless symphonic action type low level flushing cistern (ISI marked) of 10 litre capacity including 32 mm dia PVC flush pipe connected to water closet with inlet, ball valve, float and handle complete all as specified.

S&F in repair 15 mm bore PVC Connections 450 mm long with PTMT nuts complete all as specified and directed.

docileworx

Siddivinayaka Constructions