Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹10.2 CrAccepted-Finance | ₹10.2 Cr | L1 | Accepted-Finance Lowest Rate found. |
| 2 | L2₹11.3 CrAccepted-Finance | ₹11.3 Cr | L2 | Accepted-Finance high rate found. |
Tender Value
₹10.2 Cr
EMD Value
₹20.2 L
Closing Date
21 Jun 2022, 2:00 pmClosed
The Exe.,Engg., PWD, WD-I, Daman.
The Multi Office Complex, PWD, 2nd Floor, Near Moti Daman Market, Moti Daman.
Upgradation and remaining works of UT Bhawan, Chanakya Puri, New . (E-30159)
2022_DAMAN_2257_1
Tender Notice No.25/2022-23
Open Tender
Civil Works
180 days
Daman
Please refer Tender documents.
2 documents required · 2 mandatory
₹1,500
The Exe.,Engg., PWD, WD-I, Daman.
₹20.2 L
The Exe.,Engg., PWD, WD-I, Daman.
2 Aug 2022
4 Jun 2022
21 Jun 2022
4 Jun 2022
21 Jun 2022
4 Jun 2022
13 Jun 2022
Amount
Civil work
Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:3 (1 cement :3 coarse sand) etc.complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.
Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry .etc.complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.
Plaster Works--12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand) etc.complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.
15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1 cement: 6 fine sand) etc.complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.
EXPANSION JOINT TREATMENT: Providing and applying the Heavy Duty joint comprised of free float center Extruded aluminum frame and heavy duty Aluminum Frames confirm to alloy of 6063 T5/T6 specifications including providing and fixing of EPDM moisture barrier confirm to ASTM 2240 & ASTM-G53 & 84 fixing by Devin Bond confirm to ASTM C-881 complete in all respect as per manufacturer Drawing and specifications. FLOOR JOINT :- 50mm etc.complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge. Floor to Floor/Floor to Wall Joints For 50mm Gap MAFS-20/MAFSW-20.
Providing and applying the joint with no bump, Heavy duty with Devin’s seismic movement capabilities system comprised mill Finish free Float Anti skid Centre Plate and Aluminum base Frames confirm to alloy of 6063 T5/T6 including providing of EPDM moisture barrier confirm to ASTM 2240 & ASTM - G53 & 84 fixing by Devin Bond confirm to ASTM C-881 complete in all respect as per manufacturer Drawing and specifications. Basement/ Driveway Floor to Floor Joints For 50mm Gap HMF-20. etc.complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.
Providing and applying the joint with 151mm x 1.93mm thick powder coated/Anodized Extruded Aluminum frame to alloy of 6063 T5/T6 Specifications having snap locking clips system complete in all respect as per manufacturer Drawing and specifications. WALL JOINT :- 50mm Internal Wall to Wall Joints for 50mm Gap AAW-20.etc.complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.
External Wall to Wall Joints for 50mm Gap AAWE-20. etc.complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.
Providing and applying the joint with Anodized/Powder coated Centre Plate confirm to alloy of 6063 T5/T6 including providing of TWO LAYERS of EPDM moisture barrier confirm to ASTM 2240 & ASTM G53 & 84 fixing by Devin Bond confirm to ASTM C-881 complete in all respect as per manufacturer Drawing and specifications. ROOF JOINT :- 50mm.Roof to Roof/Roof to Wall Joint For 150mm Gap RFL-20/RFLW-20. etc.complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.
FLOORING WORK / WALL TILING WORK Providing & laying Matt / Glossy of 1598mm x 798mm flooring tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 25mm thick (Average) cement mortar 1:3 (1 cement : 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments.etc.complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge. Make Nexion Shade Amani Bronze
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size) etc.complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.
Providing and laying machine cut, mirror polished, Italian Marble stone for clading laid in required pattern in linear portion of the building all complete as per architectural drawings, with 18 mm thick stone slab laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm including pointing with white cement slurry admixed with pigment to match the marble shade including rubbing, curing and polishing .etc.complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge. 18 mm thick Italian Marble stone slab Statuario Marble (Base Rate of Marble is Rs.2000/ Sft)
LAMINATED WOODEN FLOORING WORKS Note :- Providing and laying 8mm thk laminated wooden flooring ( grade AC5 ) as per approved sample, colour and laid on the existing levelled flooring with approved adhesive & Scratch-guard Advanced protection wear layer for superior scratch and scuff resistance.Micro bevel edges with Click-joints for snap-together installation and a core of moisture resistant high-density fiber board With factory installed sound reducing under layer and on site vapor barrier . including expansion joints etc. complete as per manufacturers specification & approval of Architect. The vendor to ensure that the base flooring is absolute lvl, without undulation before installation. Back to back 10 year Manufacturer warranties, and guaranties to be provided by vendor.(Basic rate Rs. 400 / sqft). (Oak Spice KAARA make or equivalent make) 8mm thk laminated wooden flooring ( grade AC5 ) etc.complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.
LAMINATED WOODEN SKIRTING/BEADING WORKS Note :- .Providing and laying Skirting/ beading ( grade AC5 ) as per approved sample, colour and laid on the wall or floor with approved adhesive & ScratchGuard Advanced protection etc. complete as per manufacturers specification & approval of Architect. The vendor to ensure that the base flooring is absolute lvl, without undulation before installation. Back to back 10 year Manufacturer warranties, and guaranties to be provided by vendor. (Oak Spice KAARA make or equivalent make) etc.complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.
Providing and fixing China mossaic tiles on terrace of all colour, design , fixing in customize design as per direction of Engineer-in- Charge. The China mosaic tiles to be fixed on the terrace/wall surface with the help of approved adhesive applied at the rate of 2.5 kg per sqm and grouting of the same. The rate is inclusive of all operation, material and required pattern approved by Engineer-in-Charge:
Granite in Staire Case Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite stone slab all colour and texture except black, Cherry/Ruby red Area of slab upto 0.50 sqm
CLADDING - (EXTERIOR STONE CLADDING WORK) Providing and fixing dry cladding with Bansipal Stone 17-18mm thick uncut slab including SS 304 clamps, anchor fastners, nut bolts etc., on existing MS frame etc.complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge. Width of the stone from 3" to 12" will be considered in Running feet.
Supplying and performing CNC work on Sand Stone 50mm thick complete as per design and drawings and complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.
Labour for carving Column Capital made from Sand Stone and fixing of Capital complete as per design and drawings and complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge. (The cost of stone shall be paid sepately).
Supply of Sand Stone for Capital Carving.
Providing and fixing structural steel frame (for dry cladding with 30 mm thick gang saw cut with machine cut edges sand stone) on walls at all heights using M.S. square/ rectangular tube in the required pattern as per architectural drawing, including cost of cutting, bending, welding etc. The frame work shall be fixed to the wall with the help of M.S. brackets/ lugs of angle iron/ flats etc. which shall be welded to the frame and embedded in brick wall with cement concrete block 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size) of size 300x230x300 mm, including cost of necessary centring and shuttering and with approved expansion hold fasteners on CC/RCC surface, including drilling necessary holes. Approved cramps/ pins etc., shall be welded to the frame work to support stone cladding, the steel work will be given a priming coat of Zinc primer as approved by Engineer-in-charge and painted with two or more coats of epoxy paint (Shop drawings shall be submitted by the contractor to the Engineer-in-charge for approval before execution). The frame work shall be fixed in true horizontal & vertical lines/planes.
EXTERIOR PAINT WORK-Providing and applying Spectrum Parlina texture paint on Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equarlied on decorated wall surfaces (two coats) to give an even shade and final finish after thoroughly cleaning the surface to remove all dirt, dust and other foreign matter etc. including sand paper smooth complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.
RAILING AND WROUGHT IRON WORK-Providing and fixing stainless steel ( Grade 316) railing made of round Hollow tubes, channels, plates etc.,weight should be minimum 17kg per running meter including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge.Providing and fixing stainless steel ( Grade 316) railing made of round Hollow tubes, channels, plates etc.,weight should be minimum 17kg per running meter including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval and complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.
Providing and Fixing of wrought iron railing made out of wrought iron balluatres and top rail made out of wrought iron / teak wood complete in all respects i/c enamel paint / PU polish as per the design and drawing.complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.
FALSE CEILING-Techzone False Ceiling-Providing & Fixing of Armstrong Minel Fibre Acoustical Suspended Ceiling System with 19mm thick Ultima Microlook 90 Edge Tiles with Armstrong Silhouette 15mm face exposed grid in Techzone layout. The tiles shall have smooth bright laminated surface which is wipeable with dry/moist cloth with Humidity Resistance (RH) of 95%, NRC 0.70 (Avege value of Absorption Co-efficient readings taken at 250 Hz, 500 Hz, 1000 Hz and 2000 Hz) as per ASTM C423 standard, CAC of 40db as per ASTM E1414, Light Reflectance ≥88% as per ASTM E-1477, Thermal Conductivity k = 0.060 W/mK, Colour Global White, Fire Performance of class A2-s1, d0 according to EN 13501-1 with 19mm Microlook 90˚ edge and 8mm drop in Techzone module size of 300 x 1200mm/600X1200 (Tile) and 150/100 X 1200 mm. The 150/100X1200mm of module can be covered by AC Grille or light fixture of size which could fit in the module or 150/100 X 1200 X 0.5mm Plain GI Metal Tile. The scrim on the face of the tile shall be cleanable, soil and sctch resistant and having superior scrub-ability (Gardner Test). The tiles shall be classified as ISO 3 cleanroom class 1 with A+ VOC emissions (French). The tile shall have a ting of 8 or above for tests conducted for Resistance to growth of Mold in accordance to ASTM D3273. It shall be suitable for Green Building application, with Recycled content of 36%. The tile shall have certifications from GRIHA and GreenPro thereby confirming that it is an environment friendly product. The Silhouette Grid should have a web height of 38mm with black or white reveal. The grid should have rotary stiching and hardened steel locks on the cross tees. The layout of the grid shall have main tees at maximum 1200m apart from each other and 600mm maximum from the wall. The wall angle should be shadow moulding. PeriRmt trim to be Armstrong wall angles of size 3000x19x19mm, secured to walls using screws at 450mm centre to centre maximum. Installation shall be carried out as per Armstrong recommended procedure. ARMSTRONG SUSPENSION SYSTEM accessories supplied by Armstrong consisting of M6 Anchor Fasteners with hanger hole, pre-stightened hanger wire of dia – 2.5 mm of 1.80 m length having a tensile strength of 344-413 MPa and a minimum loading strength of 110 kgs. (Optionally, adjustable hook clips made of 0.7mm thick Gde 1 C55 galvanized spring steel of dimension 100 x 20mm and 4 mm aquiline wire to be used for level adjustment during installation purpose in main runners). complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.
Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge. but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum moisture resistant board.
- VVIP SUITE ROOM -Providing & Fixing of BED of Size 2038 x 1876 mm , Fully upholstered bed with metal & leather wrapped on it complete as drawings to the entire satisfaction complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge. Make: QUBA
VVIP SUITE ROOMProviding and Fixing of BEDSIDE TABLE Size: 450 x 380 mm PU finish on top & sides & metal trim,base in veneer, fabric on drawers with metal handle complete as drawings to the entire satisfaction complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.. Make: QUBA
VVIP SUITE ROOMProviding and Fixing of STUDY TABLE Size: 900 x 600 mm table & 4 Sqmt LCD ledge with Top in stone finish laminate & legs, sides in veneer with a Ledge for LCD unit in veneer and 3 drawers complete as drawings to the entire satisfaction complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.. Make: QUBA
VVIP SUITE ROOMProviding and Fixing of STUDY CHAIR Upholstered with legs in PU polish complete as drawings to the entire satisfaction complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.. Make: QUBA
VVIP SUITE ROOMProviding and Fixing of BEDROOM 3 SEATER SOFA Size: 1800 x 900 mm Fully Upholstered sofa with veneer base with metal legs & detailing complete as drawings to the entire satisfaction complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.. Make: QUBA
VVIP SUITE ROOMProviding and Fixing of BEDROOM COFFEE TABLE Size: 900 x 600 mm Top in glass & sides wrapped with veneer. complete as drawings to the entire satisfaction complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.. Make: QUBA
VVIP SUITE ROOMProviding and Fixing of DRAWING ROOM 3 SEATER SOFA Size: 2100 x 900 mm Fully upholstered sofa with side wrapped in leatherite & base in veneer with legs in metal complete as drawings to the entire satisfaction complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.. Make: QUBA
VVIP SUITE ROOMProviding and Fixing of DRAWING ROOM COFFEE TABLE Size: 900 x 600 mm Base in veneer & internal in metallic paint with top in glass complete as drawings to the entire satisfaction complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.. Make: QUBA
Providing and Fixing of DRAWING ROOM SIDETABLE Size: 600 x 600 mm Top in stone with base in veneer/metallic paint complete as drawings to the entire satisfaction complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.. Make: QUBA
VVIP SUITE ROOMProviding and Fixing of DRAWING ROOM ARMCHAIRS Size: 1000 x 900 mm Fully upholstered with legs,arms & back rest in PU finish with metal shoes & base in metalcomplete as drawings to the entire satisfaction complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.. Make: QUBA
VVIP SUITE ROOMProviding and Fixing of BEDROOM TOILET VANITY IN PU FLUTTING WITH METAL DETAILS WITH 2 DRAWERS complete as drawings to the entire satisfaction complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.. Make: QUBA
VVIP SUITE ROOMProviding and Fixing of DRAWING ROOM TOILET VANITY IN PU FLUTTINGWITH METAL DETAILS WITH 2 DRAWERS complete as drawings to the entire satisfaction complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.. Make: QUBA
VVIP SUITE ROOMProviding and Fixing of CONSOLE PU/VENEER IN HIGH GLOSS WITH METAL DETAIL complete as drawings to the entire satisfaction complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.. L: 1.50 Mt Make: QUBA
VVIP SUITE ROOMProviding and Fixing of LOUNGE CHAIR+FOOTSTOOL FABRIC+PU/VENEER FINISH+METAL LEGS complete as drawings to the entire satisfaction complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.. Make: QUBA
VVIP SUITE ROOMProviding and Fixing of DINING CHAIR Size: 450 x 450 mm Fully upholstered with legs in PU finish with metal shoes complete as drawings to the entire satisfaction of the Engineer-in-Charge. Make: QUBA
VVIP SUITE ROOMProviding and Fixing of DINING TABLE Size: 1500 x 900 mm Top in stone with base in PU finish complete as drawings to the entire satisfaction complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.. Make: QUBA
VVIP SUITE ROOMProviding and Fixing of WARDROBE Shutters in flutting Veneer with open shelves and mirror + leather detailing complete as drawings to the entire satisfaction complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.. Make: QUBA
VVIP SUITE ROOMProviding and Fixing of FOYER AREA LUGGAGE RACK Veneer complete as drawings to the entire satisfaction complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.. Make: QUBA
LOOSE FURNITURE: SUITE ROOMS-Providing & fixing of DOUBLE bed (without storage) with headboard as per detailed drawings and design:. The bed made out from MR grade plywood with required cutting & modification work proper in Line and Level with fixing of 0.7mm thick laminate on inner side with fixing of 04mm thick approved shade veneer on outer side or fixing of approved shade of fabric / leatherette / leatherette on bed with edge side pasting of PVC and as per approved shade or matching with laminate. The Headboard made out from 08mm/12mm hick plywood with fixing of approved shade fabric / leatherette with required stitching work with fitting of required hardware, material & labour etc. work completed as per detaileded drawings and complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge. - Bed Size: 1800mm x 2000mm with head board..
SUITE ROOMS Providing & fixing of bed side table as per detailed drawings. The bed side table made out From MR grade plywood with required cutting & modification work proper in Line Level with inside fixing of 0.7mm thick laminate with outside fixing of 04mm thick approved Shade veneer finish with applying of approved shade melamine polish on veneer. The side table`s will having one drawer unit (soft close telescopic channel) with bottom side fixing of 75mm height skirting and above side table fixing of 12mm thick plywood Panelling (150mm x 500mm) with veneer finish with fitting of required hardware, material & labour etc work completed as per detailed drawings. Legs of table are considered powder coating/Ionised.complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge. - Size of side Table: L 500mm x D 450mm x H 525mm
SUITE ROOMS-Providing & fixing of MINIBAR as per detailed drawings. The MINIBAR made out From 19mm/12mm/06mm thick MR grade plywood with required cutting & modification work proper in line and level with inside fixing of 0.7mm thick laminate with outside fixing of 04mm thick approved Shade veneer finish with pasting of PVC Edge band/veneer Paper as per approved shade or matching with veneer with applying of approved shade melamine (matt/glossy) polish on veneer. The MINIBAR`s will having Openable Shutter (Soft Close Auto Hinges) with 3 tray (Soft Close telescopic channel), shelves with fitting of required hardware, material and labor etc. Work to be completed as per detailed drawings and design and complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge. - Size 1000mm x 600mm x 750mm -12mm smoke glass top..
SUITE ROOMS-Providing and fixing of luggage rack next to wardrobe of following size as per the detailed drawings and design made out of plywood frame finished with modification works proper in line and level with inside fixing of 0.7 mmthick laminate and outside fixing of 4mm thick veneer of approved shade with edge side pasting of PVC edge band / veneer paper as per approved shade with melamine polish on veneer. Fixing of 4 drawer ( soft close Telescopic channel), shelves with fitting of required hardware, material and labour etc.. Work to be completed in all respects as per drawings and design and complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.. - Size L 1354mm x H 750mm x D 415mm..
SUITE ROOMS-Providing & fixing of wardrobe as per detailed drawings. The wardrobe 600mm deep made out from 19mm/12mm/06mm thick MR grade plywood with required cutting & modification work proper in Line Level with inside fixing of 0.7mm thick laminate with outside fixing of 04mm thick approved Shade veneer finish (Basic rate of veneer Rs. 85/-per Sq.Ft) with Edge side Pasting veneer Paper as per approved shade or matching with veneer with applying of approved shade melamine (matt/glossy) polish on veneer. Leatherette feel material will be placed in side for panelling as advised . The wardrobe`s will having Openable Shutter (Soft Close Auto Hinges) with inside fixing of 2 Tray & one Drawer (soft close telescopic channel), Shelves with fitting of required hardware, material & labour etc work completed as per detaileded drawingsand complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
SUITE ROOMS-Providing and fixing of study chair of size as per the detaileded drawings and design made out of solid wood with commercial density foam and matching fabric / leatherette upholstery and cushion i/c melamine polish wherever required complete in all respects and to the entire satisfaction complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge..
SUITE ROOMS-Providing and fixing of luggage rack of following size as per the detaileded drawings and design made out of plywood frame finished with veneer including melamine polish wherever required complete in all respects and to the entire satisfaction complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge. - Size L 1253mm x H 669mm x D 600mm..
SUITE ROOMS-Providing & fixing of two seatet Sofa as per drawings and design with commercial density foam, with approved fabric / leatherette finish, structure to be made out of plywood carcass and expose part will be of solidwood with melamine polish of desired shade on it, complete in all respects to the entire satisfaction complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge. Size 1800mm x 900mm.
SUITE ROOMS-Providing & fixing of wooden center table of size 1200 mm x 675mm x 450mm as per approved make & sample by Architect including all type of materials, hardware, loading, unloading, accessories etc complete as per detaileded drawings, specifications &complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge..
SUITE ROOMS-Providing & fixing of vanity counter as per detailed drawings. The vanity counter made out from 19mm/12mm/06mm thick MR grade plywood with required cutting & modification works, proper in line and level with fixing of 0.7 mm thick laminate on inner surfaces and fixing of 04mm thick veneer of approved shade on the outer side with pasting of PVC edge band / veneer paper as per approved shade or matching with veneer including application of approved shade melamine (matt/glossy) polish on veneer wherever required including providing and fixing of marble top as per drawing. The vanity counter shall have openable shutter (Soft Close Auto Hinges) with fixing of 2 drawers (Soft Close Telescopic Channel), shelves with fitting of required and approved hardware, materials & labour etc. The work to be completed as per detaileded drawings and design or as approved by the Architect or Engineer-in-Charge. - Size: L 1600mm x D 600mm.
LOOSE FURNITURE: STANDARD ROOMS / DELUX ROOM-Providing & fixing of DOUBLE bed (without storage) with headboard as per detailed drawings. The bed made out From MR grade plywood with required cutting & modification work proper in Line and Level with fixing of 0.7mm thick laminate inside with fixing of 04mm thick approved shade veneer finish outer side or approved shade fabric / leatherette on Bed with edge side pasting of PVC and as per approved shade or matching with laminate. The Headboard made out from 08mm/12mm thick plywood with fixing of approved shade fabric / leatherette with required stitching work with fitting of required hardware, material & labour etc. work completed as per detaileded drawings and complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge - Bed Size: 1800mm x 2000mm with head board.
STANDARD ROOMS / DELUX ROOM-Providing & fixing of bed side table as per detailed drawings. The bed side table made out From MR grade plywood with required cutting & modification work proper in Line Level with inside fixing of 0.7mm thick laminate with outside fixing of 04mm thick approved Shade veneer finish with applying of approved shade melamine polish on veneer. The side table`s will having one drawer unit (soft close telescopic channel) with bottom side fixing of 75mm height skirting and above side table fixing of 12mm thick plywood Panelling (150mm x 500mm) with veneer finish with fitting of required hardware, material & labour etc work completed as per detailed drawings. Legs of table are considered powder coating/Ionised.complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge - Size of side Table: L 500mm x D 450mm x H 525mm.
STANDARD ROOMS / DELUX ROOM-Study Table with mirror Providing & fixing of study unit as per detailed drawings. The unit made out From 19mm/12mm thick MR grade plywood with required cutting & modification work proper in Line Level with inside fixing of 0.7mm thick laminate with outside fixing of 04mm thick approved Shade veneer finish with Edge side Pasting of veneer Paper as per approved shade or matching with veneer with applying of approved shade melamine (matt/glossy) polish on veneer. The study table`s will having two drawer unit (soft close telescopic channel) with fitting of required hardware, material & labor etc work completed as per detailed drawings. - Size of side Table: L 1090mm x D 450mm x H 1050mm - without TOP Stone Providing & fixing of study unit`s MIRROR as per detailed drawings. The mirror made out from 06mm thick plain mirror with back side fixing of MR grade plywood (as a Back Support) with all side fixing of wooden Teak patti / strip including applying of polish with required Hardware, material & labor etc work complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge. Size: L 590mm x H 1274mm.
STANDARD ROOMS / DELUX ROOM-Providing & fixing of MINIBAR as per detailed drawings. The MINIBAR made out From 19mm/12mm/06mm thick MR grade plywood with required cutting & modification work proper in Line Level with inside fixing of 0.7mm thick laminate with outside fixing of 04mm thick approved Shade veneer finish with Edge side Pasting of PVC Edge band/veneer Paper as per approved shade or matching with veneer with applying of approved shade melamine (matt/glossy) polish on veneer. The MINIBAR`s shall have openable shutter (Soft Close Auto Hinges) with fixing of 2 Drawer (Soft Close Telescopic Chanel), Shelves with marble on top finishing with fitting of required hardware, material & lobour etc work completed as per detailed drawingsand complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge - Size: L 1037mm x D 500mm x H 1050mm.
STANDARD ROOMS / DELUX ROOM-Providing & fixing of wardrobe as per detailed drawings. The wardrobe made out From 19mm/12mm/06mm thick MR grade plywood with required cutting & modification work proper in Line Level with inside fixing of 0.7mm thick laminate with outside fixing of 04mm thick approved Shade veneer finish with Edge side Pasting veneer Paper as per approved shade or matching with veneer with applying of approved shade melamine (matt/glossy) polish on veneer. Leatherite feel materil willbe placed inside for panneling as advised. The wardrobe`s will having Openable Shutter (Soft Close Auto Hinges) with inside fixing of 2 Tray & one drawer (soft close telescopic channel), Shelves with fitting of required hardware, material & lobour etc work completed as per detailed drawingsand complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge - Size: L 900mm x D 600mm x H 2400mm.
STANDARD ROOMS / DELUX ROOM-Providing and fixing of study chair of size as per the detaileded drawings and design made out of solid wood with commercial density foam and matching fabric / leatherette upholstery and cushion i/c melamine polish wherever required complete complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.
STANDARD ROOMS / DELUX ROOM-Providing and fixing of luggage rack of following size as per the detaileded drawings and design made out of plywood frame finished with veneer including melamine polish wherever required complete in all respects and to the entire satisfaction of Engineer-in-Charge. - Size L 750mm x H 550mm x W 475mm .
STANDARD ROOMS / DELUX ROOM Providing & fixing of vanity counter as per detailed drawings. The vanity counter made out from 19mm/12mm/06mm thick MR grade plywood with required cutting & modification works, proper in line and level with fixing of 0.7 mm thick laminate on inner surfaces. and fixing of 04mm thick veneer of approved shade on the outer side. with pasting of PVC edge band / veneer paper as per approved shade or matching with veneer including application of approved shade melamine (matt/glossy) polish on veneer wherever required. The vanity counter shall have openable shutter (Soft Close Auto Hinges) with fixing of 2 drawers (Soft Close Telescopic Channel), shelves with marble on top , fitting of required and approved hardware, materials & labour etc. The work to be completed as per detaileded drawings and design or as approved by the Architect or Engineer-in-Charge. - Size: L 1200mm x D 540mm.
STANDARD ROOMS / DELUX ROOM Providing and Fixing of Conference Table as per specifications mentioned below: PRODUCT : CONFERENCE TABLE SYSTEM : PERFORM - Size 6000 L X 1500 W X 750 HT mm Specifications : Table Top : 25mm Thk Table Top prelam partical board with PVC 2mm Edge Banding. Under Structure : Supported on MS Powder Coated PERFORM LEG. Wire Management : 450mm Aluminium Flip Up with soft closure and provision to mount switches and sockets on PVC Cable Dump,Vertical wire entry cover considered for Power and Data Management .complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Refurbishing of old furnitures:-Refurbishing of dining table of size 750 x 750mm including repairing, chnage of laminate, wooden beeding and melamine poilishing complete in all respects.
Refurbishing of centre table of size 900 x 900mm including repairing, chnage of laminate, wooden beeding and melamine poilishing complete in all respects.
Refurbishing of Sidee table of size 550 x 550mm including repairing, chnage of laminate, wooden beeding and melamine poilishing complete in all respects.
Refurbishing of wooden chairs icluding repairing, wooden beeding and melamine poilishing complete in all respects.
Refurbishing of L type sofa 5 seater including repairing and change of fabric complete in all respects.
SUITE ROOMS/VVIP-Providing and Fixing of DRAWING ROOM TV UNIT TV panelling in flutting veneer with stone finish laminate & veneer complete as drawings in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
SUITE ROOMS/VVIP-Providing & fixing of wooden ceiling with veneer finish as per detailed drawings. The CEILLING made out From 19/12/08mm thick MR grade plywood with required cutting & modification work proper in Line Level with outside fixing of 04mm thick approved Shade veneer finish with Edge side Pasting of veneer Paper as per approved shade or matching with veneer (+/-) with applying of approved shade melamine (matt/glossy) polish on veneer with fitting of Aluminium/Wooden plywood framing with fitting of required hardware, material & labour etc work completed as per detailed drawings and complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge - Size: L 2830mm x H 600mm.
SUITE ROOMS/VVIP-Providing & fixing of bed panelling made out of 19mm thick MR grade plywood with required cutting and modification works proper in lime and level with outside fixing of 04mm thick approved shade Veneer/wallpaper/ Leatherette with 2 numbers inlay of brass having 12mm width as per drawings and design complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
SUITE ROOMS/VVIP-Providing & fixing of bed side panelling with Charcoal sheet over 19 mm thick MR grade plywood base of approved shade as per detailed drawingsand complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
SUITE ROOMS/VVIP-Providing & fixing of plywood jamb as per detailed drawings. The jamb made out From 38mm + 38mm thick MR grade plywood with required cutting & modification work proper in Line Level with outside fixing of 04mm thick approved Shade veneer finish with Edge side Pasting of edge band/veneer Paper as per approved shade with applying of approved shade melamine (matt/glossy) polish on veneer. work completed as per detaileded drawingsand complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
SUITE ROOMS/VVIP-Providing & fixing of plywood pelmet as per detailed drawings. The pelmet made out 19mm thick MR grade plywood with required cutting & modification works, proper in line & level including fixing of 04mm thick veneer of approved shade on outer sides. with pasting of edge band/veneer paper as per approved shade with applying of melamine (matt/glossy) polish on veneer. The entire work to be completed as per detaileded drawings and design and complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.
SUITE ROOMS/VVIP-Providing & fixing of TV panelling with veneer finish as per detailed drawings. The TV panelling made out of 19mm thick MR grade plywood with required cutting & modification works, proper in line and level with fixing of 04 mm thick venner of approved shade on outer sides. with pasting of veneer paper on edges as per approved shade or matching with veneer including applying of approved shade of melamine (matt/glossy) polish on veneer wherever required. The rate also includes making of vertical and horizontal grooves of size specified in the drawings. The TV unit`s panelling having niches as per detailed drawings with veneer finish including fittings of all the necessary hardware, materials & labour etc. work to be completed as per detaileded drawings and design or as directed by the Architect or Engineer-in-Charge. Panelling must also include the following: - Study platform 50mm thick with veneer finish alongwith soft close slider with PU finish outside and lamintae inside as per detailed drawing and design and complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge - TV Panel size 2600 x 1836mm - Study table size W 1481mm x D 600mm with veneer finish..
SUITE ROOMS/VVIP-Providing & fixing of mirror panelling made out of 19mm thick MR grade plywood with required cutting and modification works proper in lime and level with outside fixing of 04mm thick mirror complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
FIXED INTERIORS (DELUX ROOMS)-DELUX ROOMS-Providing & fixing of panelling with veneer finsh as per detailed drawings and design:The panelling made out From 19mm thick MR grade plywood with required cutting & modification work proper in Line Level with outside fixing of 04mm thick approved Shade veneer finish with Edge side Pasting of veneer Paper as per approved shade or matching with veneer with applying of approved shade melamine (matt/glossy) polish on veneer.The panelling with having niche as per detailed drawings with veneer finish with fitting of required hardware, material & labor etc work completed as per detailed drawings and complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
DELUX ROOMS-Providing & fixing of plywood jamb as per detailed drawings. The jamb made out From 38mm + 38mm thick MR grade plywood with required cutting & modification work proper in Line Level with outside fixing of 04mm thick approved Shade veneer finish with Edge side Pasting of edge band/veneer Paper as per approved shade with applying of approved shade melamine (matt/glossy) polish on veneer. work completed as per detaileded drawingsand complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
DELUX ROOMS-Providing & fixing of plywood pelmet as per detailed drawings. The pelmet made out 19mm thick MR grade plywood with required cutting & modification works, proper in line & level including fixing of 04mm thick veneer of approved shade on outer sides. with pasting of edge band/veneer paper as per approved shade with applying of melamine (matt/glossy) polish on veneer. The entire work to be completed as per detaileded drawings and design and complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.
DELUX ROOMS-Providing & fixing of TV panelling with veneer finish as per detailed drawings. The TV panelling made out From 19mm thick MR grade plywood with required cutting & modification work proper in line and level with outside fixing of 04mm thick approved Shade veneer finish with Edge side Pasting of veneer Paper as per approved shade or matching with veneer with applying of approved shade melamine (matt/glossy) polish on veneer. The TV unit`s panelling with having of niche as per detailed drawings with veneer finish with fitting of required hardware, material & labor etc work completed as per detailed drawingsand complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge. - Size: L 1176mm x H 2700mm .
DELUX ROOMS-Providing & fixing of wooden ceiling with veneer finish as per detailed drawings. The CEILLING made out From 19/12/08mm thick MR grade plywood with required cutting & modification work proper in Line Level with outside fixing of 04mm thick approved Shade veneer finish with Edge side Pasting of veneer Paper as per approved shade or matching with veneer with applying of approved shade melamine (matt/glossy) polish on veneer with fitting of Aluminium/Wooden plywood Framming with fitting of required hardware, material & labor etc. work and complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge. completed as per detailed drawings..
VENEER DOORS-Providing and Fixing of DOORS 1 Main door,1 Drawing room toilet door, 1 bedroom door and 1 bedroom toilet door in veneer with metal trims, 1 RIF lock for main door + hardware for all 4 complete as drawings to the entire satisfactionand complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.. Make: QUBA
Providing & fixing of 40mm thick flush doors for rooms made with water proof shutter with required cutting & modification works including fixing of 4 mm thick veneer of approved shade as per given drawings including melamine polish complete in all respect to the entire satisfaction of Engineer-in-Charge. The te also include door fme made of MR gde plywood with veneer finish and melamine polish complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.. - Door Hardware shall be paid for sepately..
Providing & fixing of 40mm thick flush doors for toilets made with water proof shutter with required cutting & modification works including fixing of 4 mm thick veneer of approved shade as per given drawings including melamine polish complete in all respect to the entire satisfaction of Engineer-in-Charge. The te also include door fme made of MR gde plywood with veneer finish and melamine polish complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.. - Door Hardware shall be paid for sepately..
Providing & fixing of duct door made with water proof ply shutter 19mm thick with required cutting & modification works having 4mm thick Veneer on outer side and 1mm laminate on the inner side as per given drawings including melamine polish complete in all respect to the entire satisfaction of Engineer-in-Charge. The item also include door frame made of MR gde plywood with veneer finish and melamine polish complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.. - Door Hardware shall be paid for sepately..
Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality 1.5 mm thick. complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.
DOOR HARDWARE : NORMAL / OTHERS-Providing and fixing of heavy duty 1 hour fire rated stainless steel 304 Butt Hinge (102 MM x 76 MM x 3 MM), 2,00,000 cycle tested, compliant to BS EN 1935, high corrosion resistance suitable for fire rated doors with complete assembly offered by manufacturer etc, all complete with necessary screws as per specification and complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.. Makes: Taiton, Geze, Asa Abloy
Providing and fixing of stainless steel concealed door closer fully compliant to EN 1154 and EN 1154:1996+A1:2002, having size EN3 (For Door width up to 950 MM) and cycle tested to 500,000 cycles with adjustable closing and latching speeds complete with necessary screws and accessories etc. complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.. finish: Silver. Makes: Taiton, Geze, Asa Abloy
Providing and fixing of stainless steel Half Moon Floor Door Stopper with necessary screws and accessories etc. complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge. Dimensions: 45 MM finish: Stainless Steel. Makes: Taiton, Geze, Asa Abloy
Providing and fixing of Tubular Stainless Steel Lever Handle with necessary screws and accessories etc. complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge. Lever on Rose Length: 135 MM finish: Satin Stainless Steel . Makes: Taiton, Geze, Asa Abloy
Providing and fixing of Euro Mortise Lock with Back Set of 55 MM and center to center distance 72 MM with necessary screws and accessories etc. complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.. finish: Satin Stainless Steel . Makes: Taiton, Geze, Asa Abloy
Providing and fixing of 60 MM Euro Profile Cylinder lock with one side thumb turn & one side coin turn with necessary screws and accessories etc. complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge. finish: Satin Nickle . Makes: Taiton, Geze, Asa Abloy
RFID DOOR MANAGEMENT-RFID Management System Providing and fixing of dio Frequency Identification Device (RFID) stand-alone Electronic Wireless Access Control Lockset, having Stainless Steel Escutcheon, 3-Point Stainless Steel Latch Construction with Anti-friction mechanism, Panic Release Function - Deadbolt & Latch automatically retcted by inside handle for easy egress in emergency situations, high security mortise lockcase powered by 4 AA batteries that provide up to 1 year normal Usage. (make Asa Abloy) .complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge. Makes: Taiton, Geze, Ozone, Asa Abloy (For Room - Vvip , Suite, Delux)
Supply, installation, testing and commissioning of Windows® Based AA-ACC-ENCODER Plug-in-and-Play USB Card encoder which can easily assign new users & cards and modifies them or Invalidates lost or stolen cards and which can read the Audit Til of locks and cards,complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge..(For Room - Vvip , Suite, Delux) Makes: Taiton, Geze, Ozone
Supply, installation, testing and commissioning of Basic Door Management Software system "Intuitive Windows® Based, connected to a USB Card Encoder to Progm / Issue Cards", complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge. (For Room - Vvip , Suite, Delux) Makes: Taiton, Geze, Ozone
Providing of user cards which can be re-writeable having frequency of 13.56 MHz Mifare (ISO14443A) Technology.complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge. .(For Room - Vvip , Suite, Delux) Makes: Taiton, Geze, Ozone
Reads the Audit Trail Information from the Locking Devices 13.56 MHz Mifare (ISO14443A) Technology .complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge. (For Room - Vvip , Suite, Delux) Makes: Taiton, Geze, Ozone
Wallpaper, Bison board panelling, Steam beach band, Charcoal panelling, Aluminium Framing etc.-Providing and fixing vinyl or Polyster Textile wallpaper coverings with approved adhesive on existing plastered surface finished with putty , to give bubble free uniform surface. Any unevenness of the base surface shall be removed before fixing the wallcovering, all complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.
Providing & Fixing of 12+19mm x 12-25mm thick Steam Beach/Rubber wood Beading including PU Polish whever required complete in all respects to the entire satisfaction of Engineer-in-Charge.
PProviding and fixing Aluminium frame work 600mm c/c bothways for wall panelling as per design drawing consisting of aluminium tubular sections of size 50x38mm having thickness not less than 2mm. The frame to be fixed to the walls by means of angle holdfasts of suitable length out of 35x35x4mm MS/Aluminium angle duly given redoxide and paint complete with expandable anchor fasteners of 65x10mm dia fixed o @1200mm C/C bothways.The frame work shall be executed as per drawings ,specifications & complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge. (In other areas upto a Height of 4.50m)
P/F 12 mm bison board cladding on outer facade over Aluminium framework made our of 50mm Aluminum tube with anchor fasteners complete as per drawing and complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.
AUDIO AND VIDEO SYSTEMS-Conference Hall-SITC of 70-inch widescreen (176.6 cm diagonal) UV2A LCDDisplay with Pixel Pitch (H x V) 0.802 x 0.802 mm of maximum Brightness 450 cd/m2 contrast ratio of 4000:1 , Backlite LED Edge Lit with 10W+10W Speakers. sharp - make
SITC of Cable Cubby Direct connectivity of HDMI Switcher kramer make / custom
SITC of Hdmi matrix switcher 4x2 HDMI Matrix Switch Splitter EDID at 30Hz Full HD 1080P with IR Remote Control Switch Switcher Splitter, EDID RC Control kramer make
SITC of 9 U equipment Rack to house Amplifier, DSP, etc.
Cable and Connectors for Installation
Seminar Hall-SITC of 137" Motorised Screen with synchronised motor and Radio frequency Remote with Ration of 16:10 High Definition Fabric for Seamless View Make : Liberty/Draper/Suvira
SITC of Cable Cubby Direct connectivity of HDMI Switcher kramer make / custom
SITC of Hdmi matrix switcher 4x2 HDMI Matrix Switch Splitter EDID at 30Hz Full HD 1080P with IR Remote Control Switch Switcher Splitter, EDID RC Control kramer make
SITC of 14 U equipment Rack to house Amplifier, DSP, etc.
Cable and Connectors for Installation for Audio and Video System
LIFT (P&F NEW LIFT, REMOVING EXISTING LIFT)-Providing & fixing 13 passemger Lift of Schindler make with fully collective control with drive power of 5.7 KW and main supply of 415 V 50 Hz, light supply of 230v and permanent magnet machine type with Automatic return to main floor Auto.door closing final time Position indicator car 1 Tvel direction indicator car Auto. Rescue Device (ARD). directed and complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.
Removal Of Existing 8 Passanger Lift Mechanizem including Control Panel, Machine, MS Framing, Rope Etc Removal All Inbuilt Parts of Lift including required Labour, Tools & Store At Located Scrape Store as per directed and complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.
PLUMBING WORK-Providing and fixing enclosed type water meter (bulk type) conforming to IS : 2373 and tested by Municipal Board complete with bolts, nuts, rubber insertions etc. (The tail pieces if required will be paid separately) : 80 mm dia nominal bore
Providing and fixing C.I. dirt box strainer for bulk type water meter with nuts, bolts, rubber insertions etc. complete conforming to IS : 2373 (Make:Sant,Zoloto,leader) 80 mm dia
Providing and laying Non Pressure NP-3 class (Medium duty) R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete 450 mm dia RCC pipes
Providing, laying, jointing and testing heavy quality DWC (Double wall Corrugated ) under ground application pipes for Sewer and strom line with Snap-Fit Coupler with Rubber Ring / In-line Socket Molded Coupler / Socket-Spigot Arrangement fittings of SN8 class of approved make laid to required alignment and slope trenches inclusive of excavation in all soil types, bailing or pumping out water from trenches, shoring, whenever necessary testing, refilling, in layers, ramming & consolidation, removing away the surplus earth & spoils, dumping it on site or carting away to lead of 100 meters as directed incl. 150 mm dia
200 mm dia
250 mm dia
Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes /UPVC /DWC Pipes including bed concrete as per standard design -b)150 mm dia diameter
c) 200mm dia diameter
d) 250mm dia diameter
Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 150 x 100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Extra for depth for manholes : Size 90x80 cm With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Extra For Depth Manhole Size 120x90 cm With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS: 1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture’s permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.
Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design : with common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 Fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design: Inside dimensions 455x610 mm and 45 cm deep for single pipe line : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Inside dimensions 600x 850 mm and 45 cm deep for pipe line with three or more inlets : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Extra for depth beyond 45 cm of brick masonry chamber : For 455x610 mm size With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
For 600x860 mm size With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Providing, Fixing, Jointing, Testing and commissioning of polyproplene low noise pipes, PP pipe and fittings conforming to DIN EN 1451-1 and DIN 19560 -10 for soil,waste and vent, including all fittings with or without access i.e bends, junctions, cowls, offsets, couplers, connectors, heavy duty metal pipe clamps etc. and jointing with pushfit rubber ring complete as directed and complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge. 110 mm Dia.
Providing, Fixing, Jointing, Testing and commissioning of polyproplene low noise pipes, PP pipe and fittings conforming to DIN EN 1451-1 and DIN 19560 -10 for soil,waste and vent, including all fittings with or without access i.e bends, junctions, cowls, offsets, couplers, connectors, heavy duty metal pipe clamps etc. and jointing with pushfit rubber ring complete as directed and complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.. 75 mm Dia.
SUB-HEAD: II : HIGH SIDE EQUIPMENTS-Supply, installation, testing & commissioning of Submersible single stage single entry pumps connected to submersible motor (The motor shall be IE3 watertight according to IEC class IP 68, and incorpote class F, insulation materials to withstand a continuous opeting tempeture of 155 deg C) for 415 + 10% volts, 3 phase, 50 cycles A.C. power supply with mechanical seal, pump connector unit Or Auto Coupling with rubber diaphgm and bend, vertical discharge pipe,Outdoor type Control panel, pumps at high level with cut off at dry level as determined. The pump shall be provided with a lifting devise of pull chain/guide il & G.I. heavy class rising main of 5m length including interconnecting piping, valves (Ball Valve / Butterfly), Non return valves (GM/CI) 15 m cable etc.High level and low level sensor with motorized butterfly valve as per requirement complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.. (Pumps shall be installed in a set of two pumps One working and One standby, with cascade opetion). For supplying Domestic Water up to terce Capacity per pump - 180 LPM Head - 25 mtr 1 Set = 2 Nos. Pump (1 Working + 1 Standby - cascade opetion) Suction head - flooded positive suction (Make:Kriloskar,Lubi)
Variable Speed Hydro-booster System for domestic water supply : Compact self contained Hydro-booster system comprising of following : In-line, vertical multistage, centrifugal clear water pumps with SS-316L /304 casing, S.S 3I6L impeller and SS-304/316 shaft, SS-316L/C.I. Base CED coating & head TEFC IE3/IE4 magnetic motor with mechanical seal with Company fitted with company compliance certificate. Vendor to submit performance curves and technical catalogue with all GA Dwing of the proposed model for review and information.Panel mounted PLC and HMI Based multi pump controller with large gphical display with VGA 240 x 320 pixels and variable frequency drive (VFD) integted in a Panel/Inbuilt with pump motor with IP54 class with pressure sensor tnsmitter (each pump each VFD), diodes to indicate pump ready, pump running and fault and capable to communicate with other controllers following MODBUS-RTU or BACNET Class-2 protocol through RS485 port. All alarms should be displayed in the controller. System should be equipped with dry running protection by both, reputed make Float (NO/NC) having 20 Mtrs Submersible Cable installed in the Tank & 0-10V DC Device installed on Suction Header. Indication of all type of faults / on-off status / electrical pameters shall be available on panel and centl IBMS monitors. On-off opetion for all pumps shall be available on BMS system.Global / Equivalent Make Pre-charged diaphgm pressure vessel with 3 years warnty from manufacturing date and company tested replaceable membne, charging connection, connected to outlet header with necessary flanges, gaskets, isolating valves, nuts/bolts etc. complete (size of pressure vessel shall be following capacity or as per manufacturer recommendation). Vessel Shall be pre-charged with Nitrogen as per respective Pump Head. Each Vessel shall be installed with 2 1/2" SS 304 Glycerine Filled Manometer on Top.Set of accessories such as SS 304 / MS with CED Coated headers for suction and discharge, control valves, non return valves, pressure tnsducers, pressure gauge, inter connecting power and control cabling etc. complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge. Domestic Water Booster Pump Flow:200 LPM Head:35m 1 Set = 2 Nos. Pump (1 Working + 1 Standby - cascade opetion) Suction head - flooded positive suction
Heat Pumps:-Supply of Air Cooled Skid Mounted heat pump following capacity at below mentioned opeting conditions with CFC free refrigent, Single compresssor & circuits, driven by suitable KW Sq. Cage induction motor complete with air cooled condenser, insulated condenser with refrigent piping, Refrigent and gas and Oil (First Charge), Microprocessor based control panel, factory mounted, motor starter & accessories etc. all mounted on M.S. fme. Motor shall be highly efficient and suitable for 380 volts ± 5%,50Hz ± 5 %, A.C. supply. (Make: Jaquar)complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge. Warnty : Tank : 3 Years Comprehensive : 1 Year Refrigerent - R-410a Output Heating capacity - 18 KW
Supply and Installation of Hot water stoge tank of the capacity of 2500L fabricated with Milld steel Working Pressure 6 Bar. The tank will have Epoxy internal coating on the internal surface for any rust protection. Warnty : 3 Years. Stoge capacity : 2500 litres Working pressure: 6.5kg/cm2 complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.
Providing and fixing forged bss lever opeted flow control ball valve of full flow with forged bss ball (Machined to mirror smooth finsh with hard chrome plated) and spindle with setting and gland of superior quality having minimum working pressure of 16 kg/cm2 etc. complete in all respect. Make : Zoloto 25 mm dia.complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.
Providing and fixing non return valve including nuts, bolts, 3mm thick rubber insertions complete, class PN 1.6. Make : Zoloto 25 mm dia.complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.
Providing and fixing starinless steel pressure gauges with glyceren filled and pressure from 0-7 kg/cm2 complete and of dial dia 100 mm. complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.
Providing and fixing starinless steel tempeture gauges and tempeture from 100 deg C complete and of dial dia 150 mm. complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.
Providing and fixing pressure reducing valve (PRV) for supply line. PRV is tested to a pressure not less than 7.0 kg/cm2 and suitable to release the pressure as desired, including flanges/unions, nuts, bolts and washers complete as required for application. Pressure Release Valve 25mm dia. complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.
Providing and fixing bss double acting air valve of approved quality with bolts, nuts, rubber insertion, tail pieces, tapers etc. if required as complete. Air Release Valve 15 mm dia.complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.
Hot Water Pumps for Hot Water Recirculation suitable for upto 90degrees Celcius. The pump set shall be duly mounted on common fabricated base fme and shall be complete with mechanical seal, TEFC induction motor suitable for 220 volts / 415 volts, single phase / 3 phase, 50 cycles A.C. supply, 150 mm dia pressure guage with gunmetal isolation cock, anti vibtion pads etc. Material of Construction (M.O.C): Corrosion Resistant in genel and suitable for hot water complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge. M.O.C : Casing — Cast Iron : Impeller — Stainless Steel : Shaft — Stainless Steel. Discharge : 3200Lph ,Head : 20 M TYPE - HORIZONTAL
Providing and fixing of M.S. structul work fabricated from standard sections i.e. rounds, solid angles, slotted angles, channels including cutting to size, drilling, welding, fixing and welding.complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.
Providing and fixing of Electrical Control Panel for Heat Pump, Electrical Elements and Pump control system complete as per required and complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.
Providing and fixing of set of CPVC pipes with nitrile insulation and Al cladding and fittings for the interconnection of Heat Pump, circulation pump and the Tank.complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.
Installation and commissioning of the above equipments related to Heat pump at site form Ra -109 to Ra - 120
ELECTRICAL WORK-PANELS-Providing & erecting weather proof, dust & vermin proof, floor mounted front opeted indoor type cubical panel board having IP-64 protection made from 14 SWG thick CRC M.S. sheet for outer body & doors, 16 SWG thick CRC M.S.sheet for internal partitions with necessary supporting angles, flats including cutting, bending, drilling, welding, riveting with internal partitions & cable alley as per requirements & instruction of engineer-in-charge with erection, supplied switch gears, BUSBARS, with suitable size of inter connecting PVC copper wire / copper-aluminium strips, rubber grommets, rib, bakelite control fuses for measuring instruments, earth bus & earth bolts, foundation flange - bolts-base Plates, sufficient nos. of hinged doors, handles with locking arngement and rubber gasket complete. The Panel shall be painted with epoxy powder coating. (The tes includes the cost of switchgears, bus bars, inter connecting mains & Copper Aluminium strips, meters, Fuses etc. The dimension shall be measured excluding base beams) The panel shall be supplied with following approved manufacturers as per attached SLD - MAIN LT PANEL (as per attached Single Line diagm) - INDOOR DOUBLE DOOR complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
UPS Panel (Specification as above & as per attached Single Line diagm) complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
TERCE AC power Panel (Specification as above & as per attached Single Line diagm) complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
External Lighting Panel (Specification as above & as per attached Single Line diagm) complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
115KVAR APFCR PANEL (Specification as above & as per attached Single Line diagm) complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Surge Protection Devices (SPD) Supplying, Assembling, levelling, connecting & testing following VSPs etc in boards as specified in 8.1, 8.2 & 8.3 1.4KV Protection level FP ,Class 'I', (Imax-40KA, 8/20µS) LEGND Cat no. 3938 or Equivalent complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
1.2KV Protection level FP, Class 's', (Imax-15KA, 8/20µS) LEGND Cat no.3943 or Equivalent complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
1.2KV Protection level DP, Class 's', (Imax-15KA, 8/20µS) LEGND Cat no. 3941 or Equivalent complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge 125 A,36KA,FP MCCB
Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Providing and fixing H.T. danger notice plate of 250 mm X 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Supplying,installation,testing and commissioning of Astronomical time switch of following configuration to be mounted in feeder pillars / Lighting DBs for automatic switching On & OFF of street lights at sun set & sun rise or twilight(Auto ON, Auto OFF, Auto modes) with manual override facility with 12/24 hour display format with suitable battery and indication for relay status i/c programming at site complete as required. : 3 output (1output per phase) and suitable for three phase supply complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Providing and erecting approved make light control unit suitable to opete on 230V +20% having ON/OFF delay time of 30-50 seconds and having facility for Auto/manual system having two LDR lens to intensity light having capacity of 5A complete erected on section pillar with pipe and stand. Supplying & erecting power contactor for time switch complete erected as per direction Cat III 4 pole 440V 40 Amp. complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Supplying and fixing following way, single pole and neutral,sheet steel, MCB distribution board, 240 V, on surface/ recess,complete with tinned copper bus bar, neutral bus bar, earthbar, din bar, interconnections, powder painted includingearthing etc. as required. (But without MCB/RCCB/Isolator) : 12 way , Double door.complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
WIRING AND CABLING-Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. : Upto 35 sq. mm
Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc as required. : Upto 35 sq. mm
Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistnd Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size of cables.(a) 4 core 2.5 Sq. mm complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistnd Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size of cables.(a-1) 4 core 4 Sq. mm complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistnd Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size of cables.(B) 4 core 6 Sq. mm complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistnd Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size of cables.(B) 4 core 10 Sq. mm complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistnd Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables(c) 4 core 10 Sq. mm complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistnd Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables(d) 4 core 16 Sq. mm complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistnd Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables (A) 3 1/2 core 25 Sq. mm ( 16 Sq. mm 1/2 core) complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistnd Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables (A-1) 3 1/2 core 35 Sq. mm ( 16 Sq. mm 1/2 core) complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistnd Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables (G) 3 1/2 core 185 Sq. mm ( 95 Sq. mm 1/2 core) complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistnd Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables (H) 3 1/2 core 240 Sq. mm( 120 Sq. mm 1/2 core) complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Providing and, fixing heavy duty flange type bss cable gland with rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for following size of cables. Solderless crimping type Copper lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool & connected to switchgear terminals with bss/cadmium plated nut bolts in an approved manner. (E) 4 core 4 Sq. mm / 4 core 2.5 Sq. mm complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Providing and, fixing heavy duty flange type bss cable gland with rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for following size of cables. Solderless crimping type Copper lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool & connected to switchgear terminals with bss/cadmium plated nut bolts in an approved manner. (E) 4 core 6 Sq. mm & (E) 4 core 10 Sq. mm complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for following size of cables. Solderless crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. (E) 4 core 10 Sq. mm
Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for following size of cables. Solderless crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. (A) 3 & 1/2 core 25 Sq. mm
Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for following size of cables. Solderless crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. (B) 3 & 1/2 core 35 Sq. mm
Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for following size of cables. Solderless crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. (G) 3 & 1/2 core 185 Sq. mm
Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for following size of cables. Solderless crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. (H) 3 & 1/2 core 240 Sq. mm
Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 100 mm width X 50 mm depth X 1.6 mm thickness
150 mm width X 50 mm depth X 1.6 mm thickness
300 mm width X 50 mm depth X 1.6 mm thickness
Fabrication : Supplying , fabricating and installation of various sizes clamps for cable ty supports using available M.S. sections & rod as per drawings or instructions of engineer in charge or consultant including applying zinc chromate yellow oxide and two to three coats of required enamel paints with anchor fasteners etc.complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
HEAT / FIRE RESISTANT COATING OF CABLE Supply and application of intumescent based coating on cables/ cable ty using CP 678 firestop cable coating of HILTI make or equivalent. The coating shall have a density in the nge of 1.2 to 1.4 Kg/ L. The coating shall be non-toxic, asbestos and halogen free and shall have good mechanical strength. The coating shall comply with IEC 332 part 3 (1992). complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
RACEWAY / TRUNCKING-Supplying & laying under floor pregalvanised corrosion proof rectangular sheet steel cable trunking of 1.6 mm thick having with stand point load up to 1.33 Ton & free from seepage of concrete of screed water having following size of dimensions and No of compartments (W x D x T) : 150mm x 38mm x 1.6mm with Three Compartments complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
[C] G.I. Junction cross over box for metal / Al. trunking with duct entry 25mm x 38mm size having epoxy powder coated tp lead with corrosion & rust free having load bearing capacity of 3.6 TONS with adjustable levelling screw of following size.150mm x 150mm x 60/75 mm depth complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
[C] G.I. Junction cross over box for metal / Al. trunking with duct entry 25mm x 38mm size having epoxy powder coated tp lead with corrosion & rust free having load bearing capacity of 3.6 TONS with adjustable levelling screw of following size.300mm x 300mm x 60/75 mm depth complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 100 mm width X 50 mm depth X 1.6 mm thickness
150 mm width X 50 mm depth X 1.6 mm thickness
300 mm width X 50 mm depth X 1.6 mm thickness
EXHAUST FAN, CEILING FAN KEY TAG LAG, NURSE CALLING-Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required.complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Supply, Install, testting Commission of 32A DP Key-tag electronics time delay .complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Supply, Install, testting Commission of 60-Port Nurce calling system for Servent calling .complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.
Supplying & erecting approved make low noise decotive exhaust fan having size 200mm with 1350 RPM with square fme ABS body with inbuilt lowers & square frame. .complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Supply,installation, testing and commisioning of 600x600mm LED Panel Light of 42W LED Lamp White CRCA Luminaire Body and Micro prismatic diffuser, LUMEN EFFICACY > 120lm/w, PF >0.90, THD <20%,SPD 4kv CCT 6000K, powder coated housing, reflector, Diffuced PC cover with LED Panel and driver.Make : Trilux, Wipro, Philips .complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Supply,installation, testing and commisioning of IP-65 -IK 07 ,10-12W LED Bollard light with die cast aluminum die cast powder coated housing, reflector,with LED lamp and driver.Make : Trilux, Wipro, Philips .complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Supply,installation, testing and commisioning of IP-65 3-6W LED foot light with die cast aluminum 150-200 mm long Recessed / surfaced, IP-65 powder coated housing, reflector, toughened glass cover with LED lamp and driver. Make : Trilux, Wipro, Philips.complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Supply,installation, testing and commisioning of Abby Ikapp 50 WATT : 15 watt , Finish : White , Beam Angle : 34 Degree , TDH : <10 , CCT: 4000K .complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge Make : Trilux, Wipro, Philips, Abby.
Supply,installation, testing and commisioning of 4W/Mtr LED strip light with indoor application with All require accessiers and Drivers LUMEN EFFICACY >90lm/W, PF >0.90, THD <20%, CCT 4000K, .complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge Make : Trilux, Wipro, Philips, Abby
EARTHING-Supplying & erecting earth pit of minimum bore dia.150mm size approved make Earthing Electrode consisting Pipe-in-Pipe Technology as per IS 3043-1987 made of corrosion free G.I.Pipes having Outer pipe dia of 50mm having 80-200 Micron galvanising, Inner pipe dia of 25 mm having 200-250 Micron galvanising, connection terminal dia of 12mm with constant ohmic value surrounded by highly conductive compound with high charge dissipation suitable for following type of applications. (c) For Electrical Installation covering Tnsformer Neutls, Lightning arrester Earthing, A.C.Plant & Sensitive Computer System(like Automation, SCADA) i.e independent Earthing in normal soil..complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge Length of Pipe : 3.00 mtrs Back filling Compound :2 nos Bags of 25 Kg.
Supplying & erecting earth pit of minimum bore dia.150mm size approved make Earthing Electrode consisting Pipe-in-Pipe Technology as per IS 3043-1987 made of corrosion free G.I.Pipes having Outer pipe dia of 50mm having 80-200 Micron galvanising, Inner pipe dia of 25 mm having 200-250 Micron galvanising, connection terminal dia of 12mm with constant ohmic value surrounded by highly conductive compound with high charge dissipation suitable for following type of applications. (b)For Electrical installation up to 11 KV in normal soil..complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge Length of Pipe : 2.00 mtrs Back filling Compound :1 no. Bag of 25 Kg.
Supplying & erecting of Conventional Lightening arrestor with Test loop and Counter as per IS standard .complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.
Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.
Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. Supply and laying of 25 mm rigid PVC pipe of 1.6-1.8 mm thickness
LAMPS-providing and fixing of Hanging light of size (Diameter) 14" and having a height of 24" complete in all respects and to the entire satisfaction of Engineer-in-Charge.
providing and fixing of table lamp and having a height of 30" complete in all respects and to the entire satisfaction of Engineer-in-Charge.
providing and fixing of standing lamp as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
providing and fixing of sittings of size 18"x12"x12" as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
providing and fixing of natul wood hanging Chandelier of size 12"x 30" as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
providing and fixing of table lamp as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
providing and fixing of wall light as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
Providing & fixing of Feather Lamp as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
Providing & fixing of Table Lamp as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge .
Supply of Classic Oli Burner
ELV SYSTEM (LAN, WIFI, TELEPNONE, CCTV)-Supplying & Fixing of Category 6, punchdown patch panels shall terminate 4-pair, 22 – 26 AWG, 100 ohm unshielded twisted pair cable with an industry standard single wire 110 punchdown tool. Patch panels shall include a universal label coded for T568A and T568B wiring schemes and mount to 19" and 23" racks. Patch panels shall be easy to identify with pre-printed numbers, write-on areas and optional label kits.Make-Commscope .complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Supplying & Fixing of Category 6 UTP patch cords shall be constructed of 24 AWG unshielded twisted pair stranded copper cable with an enhanced performance modular plug at each end. Patch cord cable shall be offered in multiple colored UTP cable for design flexibility with a clear strain relief boot on each modular plug. All patch cords shall be compatible with both T568A and T568B wiring schemes and factory Crimped. Blue UTP Cable, 1 Meter.Make-Commscope .complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Supplying & Fixing of Floor Standing Rack network Rack - 9U, Cable manager 1U MS with Loops Shelf, PDU 5 Sockets Mounting Hardware (Pkt. Of 20) complete in all respect. Make: Valrack .complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Supplying of Enhanced Category 6, CM, 4-pair, UTP copper cable. Conductors are twisted in pairs, separated by an integrated pair divider, and protected by a flame-retardant PVC jacket. Make-Commscope .complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Supply installation testing and commissioning of 1 KVA UPS with internal batteries. Make: APC .complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
ACTIVE NETWORK WORK (NETWORK SWITCHES)-Supply & Fixing of 24 port 10/100/1000BASE-P ports and four GbE/10GbE SFP/SFP+ uplink ports, layer 3 from day1 having static & RIP , stackable upto 10 switches, should support external redundant power supply, certified EAL3 , each switch should be provided with stacking port/cable Make: Juniper .complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Supply & Fixing of Dual-band 802.11abgn/ac wave 2 wall plate wireless access point, 2x2:2 streams, 1 x 1g base-t port(one 802.3af/at poe in) & 4 x 1g base-t port. 3 years AP online activation warranty. Should be controlled by cloud based controller. Make: Quantum .complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Supply installation testing and Commissioning of Access Point dual-band 802.11abgn/ac wave 2 indoor wireless access point, 2x2:2 streams, 3 x 1g base-t ports, 802.3af/at poe support. 3 years ap online activation warranty Make-Quantum .complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Supply installation testing and Commissioning of Cloud support for Wireless AP Make: Quantum .complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
TELEPNONE / DATA-Providing following type of Modular Type Accessories mounted with pvc / metallic box, single mounting base frame covered with textured / metallic front plate , modules erected with necessary connection. .complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge (8) Modem Jack for Computer Open RJ-45 - cat-III
Providing following type of Modular Type Accessories mounted with pvc / metallic box, single mounting base frame covered with textured / metallic front plate , modules erected with necessary connection. (3) Two Pin/RJ-11 Telephone Socket for One Gong Bell - cat-iii
Supplying & erecting Push button type telephone instrument (A)BEETEL Secure / BPL/, SONY / PANASONIC or equivalent make .complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. - 2 Run of Cable
Supplying & erecting Delton or approved make Telephone Cable electrolytic copper conductor PE insulation twisted in two pairs, & wpped with FRLS PVC tape & sheathed with FRLS PVC or HFFR outer Jacket suitable for telephone wiring & confirming to C-DOT erected in existing pipe. of following size of conductors & nos.of pairs. With necessary connections..complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge (b) Armoured [Jelly Filled] - 10 Pair
Supplying & erecting Delton or approved make Telephone Cable electrolytic copper conductor PE insulation twisted in two pairs, & wpped with FRLS PVC tape & sheathed with FRLS PVC or HFFR outer Jacket suitable for telephone wiring & confirming to C-DOT erected in existing pipe. of following size of conductors & nos.of pairs. With necessary connections..complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge (b) Armoured [Jelly Filled] - 20 Pair
Supplying & erecting Delton or approved make Telephone Cable electrolytic copper conductor PE insulation twisted in two pairs, & wpped with FRLS PVC tape & sheathed with FRLS PVC or HFFR outer Jacket suitable for telephone wiring & confirming to C-DOT erected in existing pipe. of following size of conductors & nos.of pairs. With necessary connections..complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge (b) Armoured [Jelly Filled] - 50 Pair
Supplying & erecting of 10-Pair Krone Box with all Box, Krone connector, Junction box of Helsel make suitable for all cable dressing as require .complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Supplying & erecting of 20-Pair Krone Box with all Box, Krone connector, Junction box of Helsel make suitable for all cable dressing as require .complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Supplying & erecting of 50-Pair Krone Box with all Box, Krone connector, Junction box of Helsel make suitable for all cable dressing as require .complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Supplying, erecting, commissioning and testing EPABX CMOS microprocessor based system having common features With remote progmming & remote dialling having following other common features. (Accord Matrix or equivalent approved make)- Auto Call Disconnector- (Incoming - Local- STD) with progmmable timing- External Call forward with DOSA- Walk in Class of service & trunk reservation- Boss ring & call back on No Reply last caller recall CLI- Hot Line with Delay & with No.- Unsupervised Conference- Serial DISA ( DISA with option to dial another No. if Extn. is No Reply)- Progmming Flexibility of all features related to timer( 41 Timer)-10 Different group of out going call restriction like 95, 97, 98 etc.Having following capacity. [C] No of Extension 60, No of Junctions 8, No of expandable ports:128, Opetors Console - 01 Compatible: ISDN .complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. Supply and laying of 25 mm rigid PVC pipe of 1.6-1.8 mm thickness
Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.
Providing & Erecting approved make following size of TV Co-axial flexible cable comprising inner conductor of solid bare copper insulated with Foam PE & Secondary conductor made of poly - Aluminium film bonded Al. Bids @ suitable covege ovell sheathed with black PVC insulation..complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge RG-11 Cable
Providing following type of Modular Type Accessories mounted with pvc / metallic box, single mounting base frame covered with textured / metallic front plate , modules erected with necessary connection. for (4) TV Co-axial Socket outlet
Supplying & Laying 24 port ck mounted switch for the following specfiication Approved by cUL Listed, CE, EN 60950, FCC Part 15 Class A, TUV, UL Listed 24 10/100/1000Mbps RJ45 ports .complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Bio metric Access Control with face detection and having a memory stoge of 35 days for 200 members .complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
CCTV - VIDEO SURVEILLANCE SYSTEM-Supply, Installation, Testing & Commissioning OF 4MP IR Indoor Dome Fixed Camera -1/2.8"Progressive Scan CMOS, 2.8mm Fixed lens, 0.01 Lux at F1.2, ICR, ONVIF, support H.265, H.264, MJPEG, 120db WDR, 3D Digital Noise Reduction, Three individually configurable stream, 12 VDC & PoE, IR range: 40m, Support on-board storage up to 256 GB (SD card not included), IP67, IK10, Intrusion detection, Motion detection, Scene change detection, Audio exception detection, video tampering, UL, FCC certified.Honeywell,Axis,Pelco .complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Bullet Camera 4 MP Vari-focal lens - Supply, Installation, Testing & Commissioning with mounting arrangement of IP Network TDN Low-Light IR Bullet Camera, 1/2.7" CMOS, 4 MP @ 25fps or better, Min. Illumination required 0.05 lux @ F1.4 (color), 120dB True WDR, ,2.7–12 mm motorized focus & zoom lens, BLC, HLC, 3DNR, Privacy Mask, 4 IR LEDs Smart IR with upto 60m IR distance, 256GB SD card support, PoE, H.265GB, PoE Class 3 and 12V DC, IP 66, Having Operating temp range : –30°C to 60° C. Certifications: ONVIF Profile S & Profile G compliant, UL, FCC certified.Honeywell,Axis,Pelco .complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
1/4" interline Colour CCD Outdoor variable Speed PTZ smoked/clear Dome pole mounting (Day/Night) IP Camera with auto motion tracker, 0.008 lux at 50IRE minimum illumination sensitivity, supporting 4 CIF resolution at 25 FPS with dual MPEG4 Streaming, electronic shutter, 26x optical zoom and 12x digital motorized zoom, 360 degree continuous Pan rotation, unobstructed -5 to +90 deg tilt, switchable automatic gain control, auto white balance, with 3.5 to 91 mm optical auto-iris lens. The camera system shall have minimum 90 presets, built -in menu system for set-up of programmable functions, on-screen compass tilt and zoom display and shall be capable of rotating the dome 180 degrees and repositioning itself for uninterrupted viewing of any object that passes directly beneath the dome and also of auto-sensing the communication protocol. The cost includes suitable size of pole for fixing camera.Honeywell,Axis,Pelco .complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Supply, installation, testing and commissioning of Professional 32 Channel NVR with video input as required for Camera mentioned above in Item no. 1,2,3. Third-party network cameras supported, H.264 Compression - Up to 5 Megapixels resolution recording, Hard Disk of minimum 6 TB as required for minimum 30 days when recording in motion @ 2CIF, 12 Frames per second (Real time). Internal storage capacity in IP Cameras for mitigating risk of IP link breakdown. HDD quota and group management, 4 SATA interfaces, 2 USB2.0, Recording on Motion, Scheduled or Alarm based. Remote backup through TCP/IP, HTTP Networkable, backup by USB/DVDWR, 3rd ONVIF.Honeywell,Axis,Pelco .complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Supply, installation, testing and commissioning of Professional 64 Channel NVR with video input as required for Camera mentioned above in Item no. 1,2,3. Third-party network cameras supported, H.264 Compression - Up to 5 Megapixels resolution recording, Hard Disk of minimum 6 TB as required for minimum 30 days when recording in motion @ 2CIF, 12 Frames per second (Real time). Internal storage capacity in IP Cameras for mitigating risk of IP link breakdown. HDD quota and group management, 4 SATA interfaces, 2 USB2.0, Recording on Motion, Scheduled or Alarm based. Remote backup through TCP/IP, HTTP Networkable, backup by USB/DVDWR, 3rd ONVIF.Honeywell,Axis,Pelco .complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Supply, installation, testing and commissioning of Professional Joystick designed for Surveillance application as compatible with the above mentioned system. UL+CE+FCC certification minimum.Honeywell,Axis,Pelco .complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Supply, installation, testing and commissioning of 8 Port Giga Switch complete in all respects .complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Supply, installation, testing and commissioning of 16 Port Giga Switch complete in all respects .complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Supply, installation, testing and commissioning of SMPS 8 Channel complete in all respects .complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Supply, installation, testing and commissioning of SMPS 16 Channel complete in all respects .complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Supply, installation, testing and commissioning of Cat 6 Cable .complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
2Core Cable for CCTV .complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
FIRE EXTINGUISHER-ABC Dry Powder type - 9 Kg. Capacity as per IS:15683 .complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
CO2 type - 4.5 Kg. Capacity as per IS:15683 .complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Supply & Installation of Sand buckets of 9L capacity as per IS:2546 .complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
Supply & Installation of M.S stand & canopy for housing 2 nos of sand buckets of 9L capacity .complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge
SOLAR POWER SYSTEM-Supply, Installation, Testing and Commissioning of ongrid Solar Photovoltaic Power Plant conforming to MNRE specifications as amended, consisting of Mono/Poly Crystalline silicon solar cells, net metering facility, necessary protections, earthing, mounted on Aluminium/GI structure of suitable strength with following components complete as required:- A) Solar Photovoltaic Module of capacity 330 Wp or above, manufactured in India, conforming to IS 14286/IEC 61215, IS/IEC 61730-Part-1, IS/IEC 61730-Part-2. Solar Photovoltaic Module conversion efficiency shall not be less than 16.5%. PV modules used in solar power plants/ systems must be warranted for their output peak watt capacity, which should not be less than 90% at the end of 10 years and 80% at the end of 25 years. B) Power Conditioning Unit (PCU) of 350-800 V DC Input voltage range and 400 V AC, three phase, 4 wire, 50Hz +/- 2.5 Hz, output voltage suitable to generate AC Power with efficiency not less than 97%, total harmonic distortion less than 3% and suitable for ambient temperature from 0 to 50 degree Celcius. The PCU shall adjust the voltage and frequency level to suit the Grid Voltage Frequency. C) Data Monitoring System complete with accessories. D) Fixing of Array junction box & Main junction box with IP 65 protection and termination arrangement for incoming and outgoing cable along with glands, lugs and other accessories etc. as required. E) Lightning and surge voltage protection. F) Connections & Interconnections by supplying & fixing required size XLPE insulated copper conductor 1.1 kV grade armoured power and control cables between solar modules, main power cable to grid supply PCU unit along with supplying & fixing of necessary channel/conduit lugs and other accessories etc. as required.
ELECTRICAL EQUIPMENTS (TEMS LIKE IRONING BOARD, STEAM IRON, LOCKERS, MINI FRIDGE, ELECTRIC KETTLE ETC)-Misc Items like Ironing Board, Steam iron, lockers, mini fridge, electric Kettle etc..Providing & fixing of self standing extra large foldable iron board with table iron stand with premium metal grilled holder white steel folding ty wire manager and aluminised surface having size 15" complete as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge. make Orril Zoshomi .
Providing & fixing of digital electronic safe locker with motorised locking mechanism complete as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge. Make Godrej .
Providing and Fixing of Mini-Fridge of 45 liter of approved Make Lg and whirlpool.
Providing and Fixing of Steam Iron of approved Make Havells
Providing and Fixing of Electric Kettle Set of approved Make Havells
DECORATIVE ITEMS ( ITEMS LIKE VASES, MURAL, CONSOLE, OIL PAINTING / CANVAS)-providing and fixing of ceramic vases shaped flower pots as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
Providing and Supplying Ex Flower Vase -44238
Providing and Supplying Ex Flower Vase -41857
Providing and Supplying Ex Glass Vase -41959
Providing and Supplying Ex Flower Vase - 44271
Providing and Supplying Ex Flower Vase - 44272
Providing and Supplying Ex Wooden Vase -V45224
Providing & fixing of ring console table in golden finish having size 15" x48" x 38" as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
Providing & fixing of Oval Mirror Table having size 18" x 24" as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
Supply of animal art as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
Providing & fixing of roviding and fixing of orignal oil painting on canvas along with FRP fmework as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
FURNISHING LINEN WORK(CUSHION, BED SHEET, DUVET AND PILLOW COVER, MATTRESS, MATTRESS PROTECTOR)-VVIP RoomsProviding & fixing of Square cushion having size 450 x450mm complete as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
VVIP Rooms-Providing & fixing of Long cushion having size 300 x450mm complete as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
VVIP Rooms-Providing & fixing of Bed Cover having size 2600 x 2600mm complete as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
VVIP Rooms-Providing & fixing of Bed throw having size 1000 x 2600mm complete as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
VVIP RoomsProviding & fixing of cushion/ pillow- polyfill fillers complete as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
VVIP RoomsProviding & fixing of Bedsheet 420 TC cotton satin having size 2700 x 2700mm complete as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
VVIP Rooms-Providing & fixing of Duvet cover 420 TC cotton satin having size 2600 x 2450mm complete as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
VVIP Rooms-Providing & fixing of Pillow cover 420 TC cotton satin having size 500x750mm complete as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
VVIP Rooms-Providing & fixing of Duvet- 250 gsm quilted polyfibre having size 2550x2400mm complete as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
VVIP Rooms-Providing & fixing of Mattress- pocketed spring with FR having size 1800 x 2000 x 210mm complete as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
VVIP Rooms-Providing & fixing of Mattress protector- 100 gsm quilted having size 1800 x 2000 x 210mm complete as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
VVIP RoomsProviding & fixing of Carpet- wool viscose-3kg/sqm hand tufted having size 1800 x 1200 x 16mm complete as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
Suite Rooms-Providing & fixing of Square cushion having size 450 x450mm complete as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
Suite Rooms-Providing & fixing of Long cushion having size 300 x450mm complete as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
Suite Rooms-Providing & fixing of Bed Cover having size 2600 x 2600mm complete as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
Suite Rooms-Providing & fixing of Bed throw having size 1000 x 2600mm complete as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
Suite Rooms-Providing & fixing of cushion/ pillow- polyfill fillers complete as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
Suite Rooms-Providing & fixing of Bedsheet 420 TC cotton satin having size 2700 x 2700mm complete as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
Suite Rooms-Providing & fixing of Duvet cover 420 TC cotton satin having size 2600 x 2450mm complete as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
Suite Rooms-Providing & fixing of Pillow cover 420 TC cotton satin having size 500x750mm complete as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
Suite Rooms-Providing & fixing of Duvet- 250 gsm quilted polyfibre having size 2550x2400mm complete as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
Suite Rooms-Providing & fixing of Mattress- pocketed spring with FR having size 1800 x 2000 x 210mm complete as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
Suite Rooms-Providing & fixing of Mattress protector- 100 gsm quilted having size 1800 x 2000 x 210mm complete as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
Suite Rooms-Providing & fixing of Carpet- wool viscose-3kg/sqm hand tufted having size 1800 x 1200 x 16mm complete as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
Deluxe RoomsProviding & fixing of Square cushion having size 450 x450mm complete as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
Deluxe RoomsProviding & fixing of Long cushion having size 300 x450mm complete as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
Deluxe RoomsProviding & fixing of Bed Cover having size 2600 x 2600mm complete as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
Deluxe RoomsProviding & fixing of Bed throw having size 1000 x 2600mm complete as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
Deluxe Rooms-Providing & fixing of cushion/ pillow- polyfill fillers complete as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
Deluxe Rooms-Providing & fixing of Bedsheet 420 TC cotton satin having size 2700 x 2700mm complete as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
Deluxe Rooms-Providing & fixing of Duvet cover 420 TC cotton satin having size 2600 x 2450mm complete as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
Deluxe Rooms-Providing & fixing of Pillow cover 420 TC cotton satin having size 500x750mm complete as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
Deluxe Rooms-Providing & fixing of Duvet- 250 gsm quilted polyfibre having size 2550x2400mm complete as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge
Deluxe Rooms-Providing & fixing of Mattress- pocketed spring with FR having size 1800 x 2000 x 210mm complete as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
Deluxe Rooms-Providing & fixing of Mattress protector- 100 gsm quilted having size 1800 x 2000 x 210mm complete as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
DormitoryProviding & fixing of Square cushion having size 450 x450mm complete as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
DormitoryProviding & fixing of Long cushion having size 300 x450mm complete as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
Dormitory-Providing & fixing of Bed throw having size 1000 x 2200mm complete as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
DormitoryProviding & fixing of cushion/ pillow- polyfill fillers complete as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
Dormitory-Providing & fixing of Bedsheet 300 TC cotton satin having size 1200 x 2450mm complete as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
Dormitory-Providing & fixing of Duvet cover 300 TC cotton satin having size 1250 x 2300mm complete as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
Dormitory-Providing & fixing of Pillow cover 300 TC cotton satin having size 350x500mm complete as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
Dormitory-Providing & fixing of Duvet- 250 gsm quilted polyfibre having size 1300x2400mm complete as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
Dormitory-Providing & fixing of Mattress- pocketed spring with FR having size 900 x 1905 x 152mm complete as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
Dormitory-Providing & fixing of Mattress protector- 100 gsm quilted having size 900 x 2000 x 160mm complete as per design approved by the architect complete in all respects and to the entire satisfaction of Engineer-in-Charge.
LABOTEK
stage.html
html • 0.03 MB
tech_eval.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid