SPECIAL REPAIR TO BLDG NO P-155 THE MALL ROAD , PROVN OF KITCHEN CABINET IN CERTAIN ORS/JCOS MD ACCN IN SRC LINE, PROVN OF STAFF TOILET IN AGE B/R-I OFFICE , ADDN/ALTN TO TOILET BLOCK NEAR BLDG NO 156 THE MALL , PROVN OF GALVANIUM SHEET AT SSP, REQMT

Amount

Demolition of brick work or stone/boulder masonary built in cement mortar incl all quoins arches pillars etc complete all as specified & directed

M&L for brick work with sub class fly ash bricks straight or curved on plan exc 6 m mean radis built in CM 1:6 complete all as specified & directed

M&L for brickwork with subclass `B' bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6 except bricks complete all as specified & directed

Demolition of cement concrete of ground floor n exc 15 cm in depth in any position nototherwise specifically provided for complete all as specified & directed

Dismantling, floor, hearth or wall tiling including cement mortar bedding but not backing and removing rubbish off the premises complete all as specified & directed

M&L for PCC 1:2:4 type B-1 (using 20mm graded stone agg) 25 mm thick for Sub base flooring complete all as specified & directed

M&L for Screed bed or bedding layer of mortar 20 mm thick in CM 1:6 for laying floor finishes complete all as specified and directed

M&L for rendering 10 mm thick in CM 1:4 for fixing of wall tiles/marble dados finishes complete all as specified and directed

M&L for ultra charged vitrified tiles 10-12mm thick (or thickness as specified by manufacture), (square/ rectangular) polished, area of each tiles exceeding 0.64 Sqm but not exceeding 0.96 Sqm (as approved by GE) in flooring set and jointed in premium epoxy grout (Kajaria KE-100 or equivalent) to match the colour of tiles and including bedding of average thickness 6mm thick premium tile for laying of tiles on brick/concrete surface complete all as specified and directed. (Note: Rates Inclusive of Premium epoxy grout, premium tile adhesive and shall not be paid separately).

All as described in Ser item No. 9.00 here-in-before but as in skirting complete all as specified and directed.

M&L for Ceramic glazed wall tiles including designer/digital/HD/Polished tiles (thickness as specified by the manufacturer), area of each tiles exceeding 0.18 Sqm but not exceeding 0.64 Sqm in flooring set and jointed in premium epoxy grout (Kajaria KE-100 or equivalent) to match the colour of tiles and including laying over cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness bedding on brick/concrete surfaces complete all as specified and directed. (Note: Rates Inclusive of Premium epoxy grout, premium tile adhesive and shall not be paid separately).

M&L for Treatment of soil under existing floors/walls using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement :2 coarse sand) to match the existing floors/wall complete all as specified & directed

M & L for premium range anti skid matt finish premium range vitrified tiles (as approved by GE) area of each tiles exceeding 0.16 Sqm but not exceeding 0.36 Sqm (thickness as specified by the manufacturer) in flooring set and jointed in premium epoxy grout to match the colour of tiles and including laying over cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness bedding on brick/concrete surfaces complete all as specified and directed. (Note: Rates Inclusive of Premium epoxy grout, premium tile adhesive and shall not be paid separately).

M&L for 16-18mm thick black granite stone slab machine cut in cooking platform, jambs, pillars, windows cills, making border/design for floors etc and the like laid over and including 15mm thick screed bed or backing coat in cement mortar (1:4) and jointed with grey cement slurry and pointed with white cement and with admixture or pigment to match the shade of granite stone including grinding and polishing and including Demolition of Stone slabs and tiles of any description or thickness in floors, aprons laid and pointed in any mortar etc. complete all as specified & directed.

Dismantling timber scantlings 40 sq. cm and over in section as in framed work, in any position complete all as specified & directed

S&F rolled mild steel as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc including notching, drilling, fittings, reveting and / or welding or connecting with bolts and nuts (including revets or bolts and nuts), providing fittings angle cleats, fish plates, gusset plates etc, also for wedging, plumbing, truing up and fixing conf to Fe-410-W (Gde-E-250) quality A complete all as specified and directed

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding/ridges to wall, fixed with self tapping screws in ridges including taking down old sheets any type complete all as specified and directed.

S &F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of a colour having tensile strength of 550 Mpa as in roof covering fixed with self tapping screws complete all as specified and directed.

S&F Mild steel flat iron as in wind ties including cutting drilling holes and securing bolts confirming to FE 410-0 of 310-0 complete all as specified & directed

M & L for provision of GI frame work (snap grid) suitable for size as in false ceiling of size 605mmx605mm including fixing 4mm thick gypsum board /E-board in ceiling size 60cmx60cm fixed to metallic snap grid consisting of following and all as directed including dismantling wall and ciling boards or insulation boards/slabs any thickness including cover fillets. (i) Gi sections incorporated in frame work shall conform to designation given in IS: 737-1986. (ii) The snap grid shall conist of GI frame work main/cross tee of size 36.5mmx25mmx1.0mm thick and 25mmx25mmx1.00mm respectively. (iii) Snap grid frame shall be fixed to ceiling with supporting hangers consisting of Supply and fix 2mm to 4mm dia mild steel Gi wire. (iv) The main and cross tees shall be jointed at junction/crossings with GI frame work angle bracket, of size 15mmx15mmx1.0mm thick, fixed with suitable mild steel, bolts, nuts and washers all as per manufacturer's instructions. (v) The snap grid(main/cross tee section) shall be supported at ends all along the wall with Gi frame work angle of size 25mmx25mmx1.00mm anodized thick (vi) Size of the snap grid shall be 605mmx605mm. (vii) Minimum average thickness of anodizing shall be 15 micron. complete all as specified & directed.

S&F wall to wall mirror of 5.5mm - 6.0mm thick fixed over plywood of required thickness complete with hard board ground fixing with rawl plug and fasteners of approved design with CP brass screw and washers i/c rubber wood moulded beading all round mirror etc. complete all as specified & directed

S & F 12mm thick toughned glass as in fixed glass, hinged doors, partitions, automatic doors, windows and similar work including cutting to shape, drilling holes, including single leg spider, ceiling/bottom to glass connector and pivots, glass to glass connector, stabilizer rod, floor clamp, plastic parts, wall to glass hinge, knob, roller, floorspring (With S.S. Cover), C Shape Square SS Handle - 450mm etc. all fittings for doors/partitions (including SS fittings) required to make functional complete all as specified & directed

S & F 8-10mm thick (Clear/ Frosted Acid wash) toughened Polish glass (meeting IS 2553 part 1 and EN-12150-1:2015) as in Frameless glass shower cubicles/partitions with Wall to wall enclosure with one end fixed glass and openable hinged/sliding door fixed with wall Coloured/transparent finished Edges (As approved by GE) including Brass hardware, door stoppers, wall to glass hinge, glass to glass hinge, wall to glass connector, floor clamp, stabilizer rod, knob, plastic parts, roller, floor guide, handles, wall brackets, floor bracket, top/bottom sliding track, L-clamps, profile strips with chrome finish and mirror finish stabilizer bar & rust Free Screws to make functional complete all as specified and directed.

Taking down of chowkhats or frame with shutters (without taking off shutters from the frames) n.exc 1.50 Sqm each complete all as specified & directed

Taking down of chowkhats or frame with shutters (without taking off shutters from the frames) exc 1.50 Sqm & n exc 4 Sqm each complete all as specified & directed

M&L for 1st class teak hardwood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed including holdfast as approved by GE complete all as specified and directed.

M&L for 30 mm thick 1st class teak hard wood heritage wood work shutter designer pattern (panelled/ plain) design pattern as approved by GE) including fixing to frame complete all as specified and directed.

S & F 30mm thick 1st class teak hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified & directed

M&L for powder coated anodised aluminium door shutters without sash bars, aluminium sections weighing 0.55 Kg/m(min) including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading,screws suitable anodised fittings such as, hinges, handles, including anodised aluminium frame with one or more rebates including 5 to 6 mm thick black glass and aluminium grill fixed to frame complete all as specified & directed

S&F powder coated anodised aluminium windows sliding (3 shutter type) type with sash bars, aluminium sections weighing 0.55 Kg/mtr (minimum) incl stainless steel mosquito proofing wire mesh fixed with , clips, frame , necessary joining cleats, glazing clips, neoprene rubber gasket with aluminium beading screws suitable anodised fittings such as hinges, handles including powder coated anodised aluminium frame, including S&F 5.50 mm thick black glass complete all as specified and directed.

S&F powder coated anodised aluminium windows side hung type with sash bars, aluminium sections weighing 0.55 Kg/mtr (minimum) incl stainless steel mosquito proofing wire mesh fixed with , clips, frame , necessary joining cleats, glazing clips, neoprene rubber gasket with aluminium beading screws suitable anodised fittings such as hinges, handles including powder coated anodised aluminium frame, including S&F 5.50 mm thick black glass complete all as specified and directed.

S & F 30mm thick 1st class teak hard wood windows, ventilators, etc. to be provided with stiles and rails as specified in SSR Part I, Section 8 clause 8.24(b), open rebated and prepared to receive glass, gauze, etc. (without sash bars), divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (b); supplied and fitted to chowkats all as specified and directed

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified & directed

S&F 4mm thick Sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 sqm in each pane complete all as specified and directed

M&L for 2nd class hardwood designer fillets, square, rectangular or triangular in section, sectional area exceeding 13 Sq.cm and not exceeding 25 Sq.cm clean sawn, secured with screw complete all as specified & directed

M&L for 2nd class hardwood designer fillets, square, rectangular or triangular in section, sectional area exceeding 6 and not exceeding 13 Sq.cm clean sawn, secured with screw.

M&L for High gloss melamine polishing on wood work (One or more Coat) over a under Coat of French Spirit polishing (two or more coat) new work including a coat of wood filler complete all as specified & directed

S&F Brass 300mm sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed complete all as specified & directed

S&F brass barrel tower bolt with bright bolt 200 mm long.complete all as specified & directed

S&F 150mm Extruded brass handles, fabricated type polished complete all as specified & directed

S&F 100 mm butt hinges, medium weight Brass complete all as specified & directed

M&L for fabrication and fixing BWP (Boiling water Proof) solid block Board 19 mm thick conforming to IS 1659- 2004 to be used ,inside depth not less than 0.50 metre. All the exposed surface which are or can be visible to be covered with 1.0 mm th. Sunmica of Approved colour, shade and finish. The surface which will come in contact with wall/ masonary/tiles etc shall be premiered with Appropriate Wood primer mixing Approved Antitermite chemical and pasting 250-micron water proof Plastic Sheet with appropriate adhesive. All the Pastings to be done with water resistant Adhesive. Any Butt joint should be strengthen with Screw and Fissures inserted with appropriate pasting compound. Shutters of storage unit to be formed out of 19 mm thick BWP ply and faced with 1.0 mm thick Sunmica. Provide shelf etc. made of 19 mm thick BWP B.B., polished to engineer-in-charge's approval. Complete Including with all necessary fittings like knobs, magnet catcher, running track for sliding, hinges any type, ball catchers, SS tower bolts 150mm , locks,SS handles 300mm long, adjustable shelves etc. as per directions of Engineer Incharge. Inside surfaces to be finished with 1.00 mm thick Sunmica and outer exposed surface with 1.00 mm th. Sunmica. Cupboard depth of 600- 750 mm. (Note: 1.Rates inclusive of solid block board, adhesives, fittings/fixtures, Sunmica and plastic sheet etc and shall not be paid separately. 2.Front facing area shall only be considered for payment ) including taking down old boarding any type.

M&L for Framed work such as grills, angle grating etc. with ends of bars shouldered and or riveted or forged into spikes, framed guard bars, railings and similar work confirming to Fe-410-O or Fe-310-O,complete all as specified & directed

M&L for preparation of new or previously untreated steel surface of any description over 10cm width or girth and applying two coat of synthetic enamel (by spraying) over one coat of primer complete all as specified & directed

S&F Mortise lock with set with Pair of 8100 Mortise Lever Handles, 271a lock with 55mm backset and 60mm EPC with one side thumb turn and one side key, Fire resistance BSEN 1634:1:2000 Certified Satin Finish Mortise Lock body approximate size of back set 45 mm X 85 mm, with 52 mm Lock and 26 mm brass latch , Stainless steel main & Strike plate & including back to back fixing feature suitable for minimum door thickness 30 mm Single door shutter with necessary fixings, screw as required to complete the work all as specified & directed.

S&F, in repair, aluminium (Die cast) body, Door closer, hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80kg and fixed. complete all as specified & directed

Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified & directed

S&F in repair 5mm thick hollow PVC Sheet wall Panelling (sand wiched between the longitudinal grid in PVC Sheet) any pattern fixing at site with PVC beading/fillet complete all as specified & directed

Taking down of cement plaster of any description from brick or stone wall etc. including raking out of joints, hacking for key, scrubbing down with water etc complete all as specified & directed

M & L for 15 mm thick rendering in CM 1:6 on fair faces of brick or concrete surfaces finished even and fair complete all as specified & directed.

M&L for 5 mm thick rendering in CM 1:3 on ceiling surfaces , finished even and smooth ccomplete all as specified & directed

M & L for applying 15 mm thick rendering in CM 1:4 on brick / concrete surfaces of external walls finished even and fiar, using water proofing compound @ 200ml per cement bag or as per manufacturer instructions, complete all as specified and directed Note:- Water proofing compound shall be measured and paid seprately. (upto a height of 15.0m)

M & L for Preparation of old surface after complete removal of existing treatment by mechanical complete all as specified and directed

M&L for preparation of old/new surfaces of ceiling and applying Two coat of distemper oil emulsion incl priming the surface and incl 1 coat ceiling birla white putty complete all as specified & directed

M&L for applying 2mm thick wall care putty making smooth surface complete all as specified and directed.

M & L for applying Two coats of 100% Premium acrylic plastic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of interior grade primer applied @ 0.90 litre/ 10 sqm over new surfaces using roller for painting complete all as specified and directed.

Taking up or down steel tubing and connection 20 mm bore pipe and removing from site complete all as specified & directed

All as described in Sl Item No.57 here-in-before but 25 mm bore pipe complete all as specified & directed

Supplying and laying of CPVC 20mm outer dia pipes SDR 11 & Plain CPVC SDR 11, with all fittings and fixed on walls/ceiling or laying in floors complete all as specified & directed

Supplying and laying of CPVC 25mm outer dia pipes SDR 11 & Plain CPVC SDR 11, with all fittings and fixed on walls/ceiling or laying in floors complete all as specified & directed

S&F triple layer white color 500 Ltrs Rotational moulded polyethylene (PVC) water storage tanks cylindrical vertical with closed top including nipple nuts and washers for fixing inlet, outlet/washout pipes and air vent pipes and including Dismantling OH water tank of capacity 500 ltr but not exceeding 1000 ltr and removing from site complete all as specified & directed

S&F 20 mm dia PTMT ball valves with brass rod, high pressure with polythene float and fly nut complete, screwed for iron pipe or for brass ferrule complete all as specified & directed

S&F in repair bib taps brass chromium plated 15 mm bore size with flange screwed down screwed for 20 mm dia pipe or for brass ferrule complete all as specified & directed

S&F brass floor door stopper body and tongue with hard drawn steel spring, fixed in floor complete all as specified & directed

S&F in repair 15 mm dia angle cock cast copper alloy chromium plated with flange screwed down high pressure with crutch or butterfly handle, flench screwed both ends for 20mm dia pipe or for union. complete all as specified & directed

S&F in repair Single Piece WC With PP Soft Close Seat Cover, Hinges, Dual Flush Cistern Fitting, Fixing Accessories And Accessories Set, Size: 360x640x685 mm including replacement of S Trap- 110 mm complete all as specified and directed

S&F in repair vitreous china thin Rim Table Top Basin (colour as approved by GE), Size: 530x420x140 mm, Shape - Rectangular including fixing acessories like galvanised brackets & rag bolts,32 mm CP waste coupling, waste pipe, bottle trap and fixing to vanity unit complete all as specified & directed

S&F in repair ,PVC(SWR) floor trap, 75mm bore, plain with grating including jointing with solvent cement complete all as specified & directed

S&F in repair ,PVC(SWR) gully trap, 125/110mm bore, plain with grating including jointing with solvent cement complete all as specified & directed

S&F 600mm Long Braided Hose with M10 x 1 Nipple, 15mm Nuts, O-Ring & Rubber Washers complete all as specified & directed

S&F in repair Maze Overhead Shower 300 x 300mm Square Shape Single Flow Body & Face plate Stainless Steel with Chrome Finish with Rubit Cleaning System with CP shower arm 24inches complete all as specified & directed

S&F in repair CP Soap Dish Holder complete all as specified & directed

S &F Grating doom 100mm dia of PTMT (Minimum weight 25gms) complete all as specified & directed

S & F in repair 75mm bore PVC Pipes single socketed in any length with rubber ring joints, fixed to walls and floor etc. as in waste complete all as specified & directed.

S & F in repair 110mm bore PVC Pipes single socketed in any length with rubber ring joints, fixed to walls and floor etc. as in waste and rain water pipes complete all as specified & directed.

S & F PVC bends 75mm bore, any radius complete all as specified & directed.

S & F PVC bends 110 mm bore, any radius complete all as specified & directed.

S&F 110mm PVC (SWR) vent cowl complete all as specified & directed

S&F 110mm PVC (SWR) 'S' trap complete all as specified & directed

S&F in repair Gun metal globe or gate valves with Iron wheel head screwed both ends for iron pipe 20 mm dia.fixed in repair complete all as specified & directed

S&F in repair Gun metal globe or gate valves with Iron wheel head screwed both ends for iron pipe 25 mm dia.fixed in repair complete all as specified & directed

S&F in repair 550mm X 750mm LED Lighting frameless, round/rectangle of required size, Anti-Fog, wall mounted backlit mirror. Thickness 5mm, round Dimmable Touch button 6000k (Cold White) SGS approved environmental protection coper free mirror all complete as per direction of Engineer-in-charge.

S&F in repair 15 mm dia brass chromium plated Central Hole Basin Mixer with Regular Spout with Popup Waste System with 450mm Long Braided Hoses fancy type with or without lettered 'Hot' or 'Cold' ,with long screwed shanks and fly nut capstan head screwed for 15mm dia pipe fixed in repair complete all as specified & directed

S&F in repair 15mm dia chromium plated fancy type Bath & Shower Mixer including Telephone Shower Crutch & Shower Kit (9537N & 571), Wall Mounted for mixing hot & cold water screwed, fixing and connection to pipes complete all as specified and as directed.

S&F in repair hand Shower (Health Faucet) with 1 meter Long Easy Flex Tube in Chrome Finish & wall Hook complete all as specified & directed

S&F in repair 15 mm dia Concealed stop cock chromium plated cast copper alloy screwed down high pressure with crutch or butterfly handle, flench screwed both ends for iron or for union fixed in repair complete all as specified & directed

S&F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf chromium plated bracket guard and railing 60cm long. complete all as specified & directed

S&F Corner Glass Shelf (with Bracket) complete all as specified & directed

S&F in repair chromium plated towel rail 450 mm long as approved quality complete all as specified and directed.

S&F in repair SS fancy type Brackets of suitable size to fix 25mm dia SS decorated curtian rod with end knobs complete all as specified and directed.(Note: 02No Bracket and 02No End knobs to be considered as one set for measurement purpose).

S & F 25mm dia Stainless steel decorated curtain rod with ring complete all as specified and directed.

Supply only liquid water proofing compound

M & L for repair to overhang portion of chajja, facia, dropwall etc. for continuous work by providing PCC(1:2:4) Type B-0 and finished with CM(1:3) after taking down of damaged portion of RCC work by maintaining same level and finished the surface to match with the existing surface by providing same finish. (Height of work to be considered above 3.5m and upto 7m from FFL of Ground Floor.) complete all as specified and directed. (Note : Wherever reinforcement is required to be provided will be paid separately under relevant item and contractor have to inform the department one day in advance after binding of reinforcement for measurement otherwise no payment will be considered on this account)

S&F in repair 12.5 mm thick tapered edge gypsum moisture resistant board (seamless type) conforming to IS: 2095- Part I. false ceiling at all heights including providing and fixing of framework made of special sections power pressed from MS sheets and galvanized with zinc coating of 120g per sqm ( both sides inclusive) as per IS 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.5mm of required length with nuts and bolt of required size and other end of angle hanger fixed with intermediate GI channels 45x15x0.9mm running at the spacing of 1200mm centre to centre to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm at 450 mm centre to centre shall be fixed in a direction perpendicular to GI intermediate channel with connecting clips made out of 2.64mm dia x 230 mm long GI wire at every junction including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall / partition with help of rawl plugs at 450 mm centre with 25 mm long dry wall screws at the rate of 230 mm interval including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screw of size 3.5x25 mm at 230 c/c including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compounds in three layers covering up to 150 mm on both sides of joints and including two course of primer & Acryllic Emulsion paint suitable for board all as per manufacturer's specification and also including the cost of making opening for light fitting, grills, diffusers cutout made with frame of perimeter channels suitably fixed, all complete as specified and directed

S & F in repair 15mm CP Two Way Angular Stop Cock with Wall Flange complete all as specified & directed

S&F in repair Brass Butter Fly Jet Spray with 1.2 meter Long Flexible Tube of premium quality fittled to Vitreous china, wash down water closet pan, Stop cock/ angle cock complete all as specified & directed

S&F Double Arm Wall Mounted Reversible Plain / Magnifying (X3) Pivotal Mirror complete all as specified and directed.

S&F in repair SS Toilet Roll Holder complete all as specified & directed

S&F in repair SS Towel Ring complete all as specified & directed

S&F Towel Rack 600mm Long with Lower Hangers, Stainless Steel complete all as specified and directed.

M&L for 18/19mm thick plywood in repair with (including) 0.8mm thick decorative mica fixed on exposed surface and white mica in internal area as in modular kitchen cabinets, inside depth not less than 0.50 M,water proof, termite & borer proof, corrosion free and auto soft closer couter sunk hinges, stainless steel handles (buff finished) complete all as specified and as directed. Note :- 1. Front facing area shall only be considered for payment 2.The labour charges for fixing of stainless steel baskets catered under Item No. 102 below shall be included in the quoted rate. 3. Rates inclusive of Stain less steel hinges, 180 degree , 304 grade.

Supply only a set of stainless steel baskets(304 grade) with fittings as in modular kitchen cabinet as per following details :- (i) Plate basket 21"x19"x8"-01 No. (ii) Plane basket 21"x19 "x 8" -01 No. (iii) Plane basket 17"x19"x8" -01 No. (iv) Butlery basket 17"x19"x4" -01 No. (v) Cup &Saucer basket 17"x 19" x4" -01 No. (vi) Single pull out 8" -01 No. (vii) GT -PT & Drip tray 22" -01 No. (viii) Stain less steel Telescopic channels of appropriate size -06 Nos. etc complete all as specified and directed.

M&L for preparation of old or previously untreated wooden surface of any description over 10cm width or girth and applying two coat of synthetic enamel (by spraying) over one coat of primer and putty after complete removal of old treatment all as specified & directed

Excavating in post holes(or similar holes) each n.exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, in soft/loose soil complete all as specified and directed

M&L for PCC 1:3:6 type C2 using 40mm graded stone agreegate as in bed blocks to fencing post complete all as specified & directed

S&F mild steel in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165. complete all as specified and directed.

S&F triple layer white color 1000 Ltrs Rotational moulded polyethylene (PVC) water storage tanks cylindrical vertical with closed top including nipple nuts and washers for fixing inlet, outlet/washout pipes and air vent pipes and incl dismantling water tanks any type & removing complete all as specified and directed.

S&F in repair Gun metal globe or gate valves with Iron wheel head screwed both ends for iron pipe 15 mm dia.fixed in repair) complete all as specified & directed

M & L for 18/19mm thick WPC solid board, exterior grade prelaminated one side with decorative choice laminations and other side balancing white lamination, fixed with SS screws to WPC frame work in cup boards, and kitchen cabinet rebated or flat edged fancy handle, each leaf 02 Nos Magnatelock, hydraullic hinges complete all as specified and directed

S&F 30mm flap width continuous (Piano) hinges, m ild steel, bright finish or electrogalvanised complete all as specified & directed

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m deep and getting out in soft/loose soil complete all as specified & directed

Surface excavation n.exc (not exceeding) 30cm deep and averaging 15 deep and getting out in soft /loose soil complete all as specified & directed

Removal of excavated material (soil) to a distance n.exc 50mtr and depositing where directed at a level n.exc 1.5m above or below the starting point complete all as specified & directed

M & L for hardcore of broken bricks gauges n.exc. 63mm, deposited spread and leveled in layers n.exc. 15 cm thick watered and rammed to a true surface complete all as specified and directed.

M & L for cement concrete (1:4:8) type D-2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete and sub base of floor complete all as specified and directed.

M&L 60mm thick PCC tile (interlocking type) with grey cement and pigment over and including 25 mm thick sand cushioning, interlocking tiles jointd filled with sand and campacted with mechanical plate vibrator complete all as specified & directed

Returning filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick as in soft/loose soil complete all as specified and directed.

M & L for Treating the top surface of filled earth at the rate of 7.50 litres of emulsion per square metre of surface complete all as specified & directed

M & L for Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the substructure in contact with backfill to be measured) complete all as specified & directed

M & L for Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified & directed

M & L for approved soil filling under the floor, spreading and levelling in layers n.exc. 25cm thick, well ramming including watering as required complete all as specified and directed.

M & L for Use and waste of Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified & directed

M & L for Use and waste of Form work of sides of pillars, posts, struts, piers, columns etc square or rectangular or polygonal rough surfaces of concrete complete all as specified & directed

M & L for Form work to sides and soffits of beams lintels etc finished rough complete all as specified & directed

M & L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200m thick flat fair finished surfaces of concrete complete all as specified & directed

M&L for form work to the edge of concrete flat n. exc 200 mm thick complete all as specified & directed

S & F mild steel TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

S & F mild steel TMT bars 6 to 8 mm dia and over, cut to length, bent to shape required as in stirrups complete all as specified & directed

M & L for RCC 1:2:4 Tybe B1 using 20 mm graded stone aggregate as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under reamed piles and mass concrete complete all as specified & directed

M & L for RCC 1:2:4 Type B1 using 20 mm graded stone aggregate as in Columns, pillars etc complete all as specified & directed

M & L for RCC 1:2:4 Type B1 using 20 mm graded stone aggregate as in beams, lintels over 1.5 m span etc complete all as specified & directed

M&L for RCC M 25 type A-1 using 20 mm graded stone aggregate for roof slabs supported on walls, beams and the like complete all as specified & directed

M & L for 75 mm thick cement concrete 1:3:6 type C-2 using (40 mm graded stone agg) as in sub base complete all as specified & directed

M & L for Non Skid ceramic tiles 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match 15mm thick screed bed in CM 1:6 complete all as specified and directed

M & L for glazed coloured ceramic tiles of size 450x300x7-8mm thick, on vertical surfaces set and jointed in neat cement slurry and pointed in white/ coloured cement to match with existing work over and including 10mm thick rendering in CM 1:4 complete all as specified & directed.

M&L 75mm thick PCC 1:3:6 type C-1 (using 20mm graded stone aggregate) as in path /plinth protection , finish even & smooth without using extra cement all as specified and directed.

M & L for preparation of new plastered surfaces of walls etc and applying two coats of cement base paint over a coat of primer complete all as specified & directed.

M & L for preparation of new plastered surfaces of walls with wall care putty and applying two coats of Oil bound distemper to match the existing surfaces as required, complete all as specified & directed.

M & L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified & directed.

M&L for padding in PCC 1:2:4 type B0 (using 12.5mm graded stone agg) laid to a minimum consolidated thickness 25mm to provide a finished slope 1:30 complete all as specified & directed

M & L for cleaning of plastered /concrete surfaces and applying priming coat using bituminous primer @ 0.30 Kg/Sqm. followed by evenly a tack coat @ 1.20 Kg/Sqm. using with 85/25 grade bitumen, over laid with 3mm thick APP modified polymeric water proofing membrane with non woven polyester reinforced of weight not less than 3.6 Kg/Sqm. unrolled and bonded to substance with side and end laps 75mm and 100mm as per manufacturer’s instructions and finished top of APP water proofing polymeric membrane with a coat of hot blown industrial bitumen 85/25 grade @ 1.20 Kg/Sqm and finally finished with a coat of bituminous aluminium paint @ 0.20 Kg/Sqm complete all as specified and directed.

M & L for gauzed shutter shall be made out of u shaped iron 35x35x5mm, 25x25x5mm and 1.5mm thick as shown on drawing. The frame for shutter shall be of pressed steel and 10mm Square bars grill complete with fly proof wire mesh having 0.63mm nominal dia wire and 1.4mm average with aperture and 250mm M S sliding bolt , 150mm MS tower bolts and Aluminium 200mm Handle including two coats of synthetic enamel paint over a coat of red oxide complete all specified and directed

M & L for Flat iron hold fast 25mm x 6mm welded to angle iron door frame complete all as specified & directed

M & L for Mild steel angle iron door frame 40mmx40mmx6mm conforming to Fe 410-0 incl 12mm dia deformed bars for strengthing at bottom of chowkhats incl cutting floor at bottom to accommodated strengthing bars & making good the floor in PCC 1:2:4 type B-0 to match the existing floor complete all as specified & directed

S & F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame, made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC , ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for to rail & bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed to getter with solvent cement, supplying & fixing in the frame at site as per specification & drawing for Item No. 08080 on page No 156 of SSR 2010 (Part-II).

S & F 125mm size aluminium alloy handles cast type anodized complete all as specified & directed.

S&F aluminium tower bolts 150mm long, of extruded section complete all as specified & directed

S & F MS helical door spring 150 mm size complete all as specified & directed

S & F PVC waste pipes of 40/32mm bore suitable for wash hand basins/sinks complete all as specified & directed.

S & F steel C.P. grating 100/125 mm dia as reqd at site complete all as directed

S&F 110 mm bore PVC floor traps plain with grating and 300 mm long out let including jointing with cement concrete type B -1 1:2:4 complete all as specified & directed.

S&F steel windows or ventilators fixed type, complete all as specified & directed.

S&F mild steel framed work such as grills, gratings guard bar etc with ends of bars shouldered and/ or riveted etc completed all as specified.

S&F 20mm Gun -metal,globe or gate valves,with iron wheel head ,screwed both ends for iron pipe and fixed complete all as specified & directed

S&F vitreous china wash hand basin, white, flat back of size 550x400mm (excluding taps, waste chain and plug and porcelain stopper) but including brackets suitable for 15mm dia pipe complete all as specified & directed.

S&F angular valve, 15 mm dia, cast copper alloy, chromium plated, fancy type with long shank and cup, screwed down, high pressure screwed both ends for iron pipes or for unions and fixed in pipe complete all as specified & directed.

S&F PVC low level flushing cistern of 9-10 ltrs capacity, ISI Marked, white, symphonic action type with inlet, ball valve, float and handle including brackets and PVC flush pipe of 32 mm bore, suitable for low level cistern complete all as specified & directed.

S&F 15mm bore, tubes medium grade, galvanized with all fittings and fixed to walls and ceiling or laid in floors including testing complete all as specified & directed.

S&F 20 mm bore, tubes medium grade, galvanized with all fittings and fixed to walls and ceiling or laid in floors including testing complete all as specified & directed.

S&F 3mm thick sheet glass, pin headed, and glazing with oil putty/beading in square not exceeding 0.50sqm each pane complete all as specified & directed.

S&F in PVC connections of 450mm long of PRYAG Make suitable for 15mm dia iron pipe including PTMT nuts complete all as specified & directed.

S&F in repair vitreous china wash down water closet pan (pedestal pattern), white (flushing cistern and flush pipe) fixed with ‘P’ or ‘S’ trap, including making good the disturbed surfaces and to match with existing surface complete all as specified and directed.

S&F in repair white plastic seat cover for W.C.(E.T.) white including M.S. CP or aluminium hinging device complete all as specified and directed.

S&F pillar taps, fancy type cast copper alloy with capstan heads, chromium plated, screwed down, high pressure with or without lettered “hot” or “cold” with long screwed shanks and fly nut screwed for iron pipe of 15mm bore, complete all as specified & directed.

S&F PVC (SWR) pipes 110 mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified & directed

M&L for Concrete bed to drain pipes 150mm, including packing under, and haunching against the sides of pipes after they are laid and tested; in PCC(1:4:8) Type D-2 complete all as specified & directed

M&L for Slat-glazed stoneware drain pipes 150 mm dia laid in trenches and jointed complete all as specified & directed

M&L for Rendring 10mm thick on fair faces of brick work or concrete surfaces in CM 1:4 complete all as specified & directed

M&L for PCC(1:3:6) type C1 as in benching to man hole complete all as specified & directed

M & L for construction of Septic tanks for 25 Users by, excavation in ordinary soil, foundation in PCC 1:2:4, brick work in CM 1:4, RCC slab covers including RCC precast manhole cover having 6mm plate embedded all around/fibre reinforced cover with angle iron frame vvent shaft and sludge chambers etc complete all as specified & directed Note:- Septic tank shall be constructed as per TD drawing of 25 Users

M & L for 15 mm thick rendering on other than fair faces of brick work or concrete surfaces,in CM(1:4) surface finished even and smooth without using extra cement complete all as specified and directed.

S & F vitreous china urinal, half stall type white, with grating, union for discharge pipe, flush pipe and waste pipe, CP urinal spreader fixed to water supply pipe etc including fixing of plugs bedding against wall in CM 1:2 complete all as specified & directed

M & L for point wiring with 1.5 Sq.mm nominal cross sectional area, single core, 1100 Volts grade, stranded, FRLS PVC insulated, unsheathed, copper conductor cable in and including PVC concealed conduit of any size/dia complete with all accessories/fittings, brass screws, washer etc, sunk zinc coated pressed steel terminal boxes with 3mm thick plastic laminated sheet top cover concealed in wall with and including continuous earth wire of size 1.5 Sqmm nominal cross sectional area, single core, PVC insulated stranded copper conductor cable, unsheathed and connected to common earth and duly complete all as specified and directed for the following :-

One tube light/Bulb, fan point / Exhaust fan, bell point .

All as described in Ser Item No. 174 here-in-before but for each additional light point on the same switch circuit

One 3 pin, 05 / 06 Amps socket outlet point on independent board controlled by one, one way 05 / 06 Amps switch.

One 3 pin, 05 / 06 Amps socket outlet point on same board controlled by one, one way 05 / 06 Amps switch.

All as per serial item No above here - in - before but with 2.5 Sqmm nominal cross sectional area copper conductor cable for one 15 / 16 Amps socket outlet point on independent board.

Material and labour for point wiring with 1.5 Sq.mm nominal cross sectional area, single core, 1100 Volts grade, stranded, FRLS PVC insulated, unsheathed, copper conductor cable in and existing PVC concealed conduit of any size/dia complete with all accessories/fittings, brass screws, washer etc, sunk zinc coated pressed steel terminal boxes with 3mm thick plastic laminated sheet top cover concealed in wall with and including continuous earth wire of size 1.5 Sqmm nominal cross sectional area, single core, PVC insulated stranded copper conductor cable, unsheathed and connected to common earth and duly complete all as specified and directed for the following :-

S & F switch piano flush type, 05 / 06 Amps single pole, one way 240 volts complete all as specified & directed by Engr-in-Charge

S & F switch piano flush type, 15 / 16 Amps single pole, one way 240 volts complete all as specified & directed by Engr-in-Charge

S & F of socket outlet 3 pin, 05 / 06 Amps and 3 pin 15 / 16 Amps (2 in 1 Multipurpose) 240 volts complete all as specified & directed

S & F of socket outlet 3 pin, 15 / 16 Amps and 3 pin 15 / 16 Amps (2 in 1 Multipurpose) 240 volts complete all as specified & directed

M & L for sub main wiring with 04 Sqmm nominal cross sectional area, two single core, 1100 Volts grade, stranded, PVC insulated, unsheathed, copper conductor cable with and including continuous earth wire of size 06 Sqmm nominal cross sectional area, single core, PVC insulated, copper conductor cable drawing into and including rigid non metallic PVC concealed conduit of 25 mm dia, medium grade with all conduit accessories / fittings, brass screws, washers etc and connected to common earth dolly including all cutting / chases etc in wall, making good to walls etc including two coats of white / colour washing / distempering etc to the disturbed surfaces to match the existing incl taking down old u/s submain wiring complete all as specified & directed.

S & F lamp holder (Angular / Straight), insulated body, with back plate 3mm thick, 100mmx100mm, complete all as specified and directed.

S & F LED lamp 9/10 watt complete all as specified and directed.

S & F of ceiling rose, 3 phase/PVC/polycarbonate isolated body complete all as specified & directed by Engineer -in- Charge.

S & F Recess/Surface mounted LED down light round /square 18watt (warm light) with high effciency effciency 100 lumen/ watt LED Luminaires LED Luminaires made in pressure die cast aLuminium Housing and opal diffuser fixed with aluminium extruded powder coated frame for uniform and glare free light complete all as specified & directed.

Supplying & fix LED 10 watt wall bracket light aesthetically designed wall brecket light with B22 (warm light) lamp holder and bulb as per sample directed by Engr-in-Charge complete all as specified & directed.

S&F unarmoured extruded PVC outer sheathed LT aluminium cable of size 6 Sqrmm 2 core. 1100 Volt complete all as specified and as directed.

S&F sheet Metal Encloser with socket , plug top & MCB single Pole and netural encloser with one single pole MCB of 20 Amp capacity 240 volts B series 10 KA and making connection complete all as specified and directed.

S & F MCB, SP, AC, 240 volts "B" series capacity of 06 to 32Amps, 10kA and making connections complete all as specified & directed.

S & F MCB, SPN, AC, 240 volts, C series capacity 40 to 63 Amp, 10 KA Amps and making connections complete all as specified & directed.

S & F MCB, SPN, AC, 240 volts, C series capacity 32 AMP, 10 KA Amps and making connections complete all as specified & directed.

S & F MCB, DB box 8 way 200 Amp 240 Volts , double door . SPN and flush to wall including all cutting etc on wall and making good the disturbed surface with painting the wall to match the existing including taking down old u/s DB all as specified & directed.

S & F MCB, DB box 12 way 200 Amp 240 Volts , double door . SPN and flush to wall including all cutting etc on wall and making good the disturbed surface with painting the wall to match the existing including taking down old u/s DB all as specified & directed.

S&F vertical TPN (VTPN) distribution board with provision for & 125 Amp MCCB TPN as incomer with necessary internal wiring , MCBs as outgoing , 12 way 415 Volt , double door for housing MCBs /Isolators and flush to wall incl all cutting etc on wall and making good the disturbed sruface with painting the wall to match the existing incl taking down old U/S DB all as specified and directed.

S&F MCCB 4 pole 415 V adjustable thermal setting , 125 Amp with breaking capacity 16 KA including taking down Old U/S MCCB complete all as specified and directed .

S&F Garden light aluminium sheet spun canopy , thick acrylic sheet molded body finished with polyurethane paint with B22 ( warm light) ABS holder cast aluminum spiot in existing pole , 09 Watt B22 bulb and light will be fixed at existing pole complete all as specified and directed.

S&F rigid non mettalic PVC Conduit of 25mm dia inclusive of all rees , bends , elbow , bell mouth tube ensa complete all as specified and directed.

S&F ceiling fan with blades down road , elecrronic fan regulator 1200 mm sweep , 230 V AC BEE, Bldg fan with five star rated complete all as specified and directed.

S&F wall fan 230 volt , 400mm sweep suitable for wall mounting complete all as specified and directed.

S & F 40W LED building security light , 230 V AC outn door type, energy saving & environmental friendly long life luminaire with high power LEDs as light source and electronic driver including security light brackets of 32 mm dia GI pipe medium grade upto 1.5 mtr long bend to shape at 100-120 degree including flat iron clamps and Suitable nuts and bolts grouted in wall including all material required for fitting incl painting with 2 coat synthetic enamel paint over a coat of red oxide and making connection with cable all as specified and directed

Material & labour for earthing complete with galvanised mild steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25mtr deep below ground level) with top edge of the plate not less than 1.5mtr below normal ground level steel earth plate connected with GI wire 04mm dia by means of lug, bolts, nuts, check nuts, washers of galvanised iron or steel GI protection pipe 15mm bore light grade all as shown in elect plate No.3 of SSR part I connecting to main switch board / Main DB’s including excavation, earth work, salt and charcoal dust mixed and packed 150mm thick around GI earth plate, GI pipe medium grade 20mm nominal bore watering pipe GI sheet funnel wire mesh, concrete pit, RCC cover in PCC 1:2:4 type B1 duly reinforced with MS Bars 6mm dia at the rate of 150mm center to center both way with suitable lifting handle and pit / chamber in PCC 1:3:6 type C1 , Angle iron 40x40x5mm frame for pit cover including testing on completion complete all as specified and directed.

S&F water cooler electric driven ( single phase) having approx storage capacity of 80 Ltr and nominal cooling capacity of 40 Ltr per hour complete all as specified and directed.

S&F Volgate stabilizer for automatic operation single phase nature air cooled indoor type and designed for input variation between 170 to 250 V with outlet voltage stabilized at 230 V with accuracy of +-05% and of capacity of 2 KVA complete all as specified and directed.

S & F LED tube light fittings T/5 surface mounting poly carbonate batten 240 V 20 watts , 6500K complete all as specified & directed.

S & F LED tube light fittings T/5 surface mounting poly carbonate batten 240 V 10 watts , 6500K complete all as specified & directed.

S&F XLPE insulated armoured heavy duty electric cable with aluminium conductor , size 10 Sqrmm 2 core. 1100 Volt complete all as specified and as directed.

S&F Exhaust Fan steel body AC single phase & neutral for 240 volts/230 volt , 300mm sweep with blades and louvers complete all as specified and directed.

S&F sheet Metal Encloser single Pole and netural encloser with one single pole MCB of capacity 240 volts 4 way 200 Amp rated bus bar flush/shutter mountaing double door complete all as specified and directed.

Supply & fixing MCB, SPN, AC, 240 volts, C series capacity 40 AMP, 50 Hz suitable for fixing in MCB DB C series complete all as specified & directed.

S&F MCB single pole 240 Volts 6 to 32 Amps 10 KA complete all as specified and directed

S&F water heater storage type steel body and heating elements upto 2KW capacity 25 Ltr BEE 5 stared complete with a rating incl providing of hold fast in wall and PVC connection 45 cm long with 15mm dia brass union at both end heavy duty complete all as specified and directed

Supply and spreading clean fine dry river sand in trenches for cusioning of under ground cable / cable duct complete all as specified and directed.

M&L for fly ash brick protection length of brick shall be laid across the length of cable all as specified and directed.

S&F Exhaust Fan PVC body 230 volt , 250mm sweep with blades and louvers complete all as specified and directed.

Material and labour for sub main wiring with 06 Sqmm nominal cross sectional area, two single core, 1100 Volts grade, stranded, PVC insulated, unsheathed, copper conductor cable with and including continuous earth wire of size 06 Sqmm nominal cross sectional area, single core, PVC insulated, copper conductor cable drawing into and including rigid non metallic PVC concealed conduit of 25 mm dia, medium grade with all conduit accessories / fittings, brass screws, washers etc and connected to common earth dolly including all cutting / chases etc in wall, making good to walls etc including two coats of white / colour washing / distempering etc to the disturbed surfaces to match the existing incl taking down old u/s submain wiring complete all as specified & directed.

Manglam Engineers and Construction Co (BID ID -3112402)

SA construction co. (BID ID -3113767)

mohanlal gupta (BID ID -3113614)

veer enterprises (BID ID -3113943)

Shri Kanchan Engineers (BID ID -3110223)