REP MAINT OF WATER SUP PUMP SETS REP TO MOTORS CONTROL PANNELS STARTER DI GI CI PIPES JOINTS SLUICE GATE VALVES FOOT VALVES PUMP SET BESEMENTS IMPROVEMENT TO INSTL ETC AT C AREA UNDER AGE EM I IN GE C KIRKEE

Amount

Excavation in trenches n.exc 1.5 mtr wide and n.exc 1.5 mtr in depth for laying of pipes etc and getting out in soft / loose soil complete all as specified and directed.

Excavation in trenches n.exc 1.5 mtr wide and n.exc 1.5 mtr in depth for lying of pipes etc and getting out in road cuttings/Hard dense soil complete all as specified and directed.

Removing surplus soil to a distance n.exc 50 mtr and depositing where directed at a level n.exc 1.5 mtr above the starting point complete all as specified and directed.

Returning filling in trenches including spreading, leveling, watering and well ramming in layers n . Exc 25 cm complete all as specified and directed.

M & L for taking up cast iron water mains (incl all fitting) 80mm bore dia of pipe with spigot and socket ends from trenches complete all as psecified and directed.

All as item no.5 above but size of pipe 100 mm bore

All as item no.5 above but size of pipe 150 mm bore

All as item no.5 above but size of pipe 200 mm bore

All as item no.5 above but size of pipe 250 mm bore

All as item no.5 above but size of pipe 300 mm bore

M & L for Cutting cast iron pipes in position for insertion of fittings, mechanical joints, replacement of pipes etc for bore of pipe 80mm

All as item no.11 above but 100 bore pipes

All as item no.11 above but 150 bore pipes

All as item no.11 above but 200 bore pipes

All as item no.11 above but 250 bore pipes

All as item no.11 above but 300 bore pipes

M & L for Laying only 80 mm bore CI pipes with spigot and socket ends laid in trenches including thorough cleaning of old CI pipe by descaling internally with steel brushes equal to bore of pipe, scraping washing properly complete all as specified and directed. (to be measured only found serviceable in all respect retrived from item No 5).

All as item no.17 but bore of pipe 100 mm.( servicable pipe received against item no.6)

All as item no.17 but bore of pipe 150 mm.( servicable pipe received against item no.7)

All as item no.17 but bore of pipe 200 mm.( servicable pipe received against item no 8)

All as item no.17 but bore of pipe 250 mm.( servicable pipe received against item no.9)

All as item no.17 but bore of pipe 300 mm.( servicable pipe received against item no.10)

M & L for Ductile iron fittings such as bends (any type, radius and angle), tapers any type (straight, bend, incresing, decreasing or double socket etc.), Tee piece, single branch 'Y'junction double branch, collar etc., caps and plugs etc. as per IS: 9523-2000 of class K-7, with internal cement mortor lining, and external zinc and black bitumen coated of dia upto 150 mm complete all as specified and directed

M & L for Ductile iron fittings such as bends (any type, radius and angle), tapers any type (straight, bend, incresing, decreasing or double socket etc.), Tee piece, single branch 'Y'junction double branch, collar etc., caps and plugs etc. as per IS: 9523-2000 of class K-7, with internal cement mortor lining, and external zinc and black bitumen coated of dia upto 200 to 300mm complete all as specified and directed

Supply, laying, jointing & testing DI-K7 class with spigot and socket, suitable for Push on rubber joint, with internal cement mortor lining, and external zinc and black bitumen coated pipes in any lengths conforming to IS:8329-2000 including Rubber Gasket & joints as per IS:9523-2000 laid in trenches/ Road/ Ducts/ Footpath/ on wall/ on floor locations for 80 mm bore dia pipe complete all as specified and directed. Make: Electro steel/Electro cast.

All as item no.25 above but 100 mm bore pipes.

All as item no.25 above but 150 mm bore pipes.

All as item no.25 above but 200 mm bore pipes.

All as item no.25 above but 250 mm bore pipes.

All as item no.25 above but 300 mm bore pipes.

M&L for taking up worn out GI steel tubing incl all fitings fron trenches of 15 mm bore complete all as specified and directed.

All as item no.31 above but 20 mm bore pipes.

All as item no.31 above but 25 mm bore pipes.

All as item no.31 above but 40 mm to 50 mm bore pipes.

All as item no.31 above but 80 mm bore pipes.

All as item no.31 above but 100 mm bore pipes.

All as item no.31 above but 150 mm bore pipes.

S & F and Laying in trenches/fixed to wall galvanised steel water tubing 15 mm bore, medium grade with and including all medium grade fittings complete all as specified. Make:Tata/Jindal or equvalant.

All as item no.38 above but 20 mm bore pipes.

All as item no.38 above but 25 mm bore pipes.

All as item no.38 above but 40 mm bore pipes.

All as item no.38 above but 50 mm bore pipes.

All as item no.38 above but 80 mm bore pipes.

All as item no.38 above but 100 mm bore pipes.

All as item no.38 above but 150 mm bore pipes.

M&L for taking appart and reassembling stuffing box of sluice valve S.S. Spindle in position suitable for existing sluice valve including replacement of gland packing. Note: (i) Nuts, bolts & washers wherever required new shall be measured and paid separately as supply only.

S&F in repairs CI body non raising SS spindle sluice valve with cast iron wheel, of size 80 mm bore, class PN-1.6 with SS spindle with brass nut, both ends flanged confirming to IS-14846 with standard bolts hole, fixing with nuts, bolts, washers, rubber gasket etc complete in position of pipe line all as specified and directed. Note for item no.47 to 53: (i) Nuts, bolts & washers wherever required new shall be measured and paid separately under respective item. (ii) Rubber gasket shall be inclusive of the quoted rate.

All as item no.47 above but 100 mm bore

All as item no.47 above but 150 mm bore

All as item no.47 above but 200 mm bore

All as item no.47 above but 250 mm bore

All as item no.47 above but 300 mm bore

S&F in repairs cast iron air release valves with air outlet,100 mm dia flanged including fittings as required at site, making necessary modification/ arrangements and on CI/MS/DI pipeline of bore up to 450 mm

M &L for dismentling & taking out carefully sluice valve head with gate, spindle and stuffing box of size 80 mm to 300 mm bore in position, replacement of worn out SS/GM spindle & GM nut with new SS/GM spindle or GM nut for sluice valve class PN 1.6/ 1.0, and refixing gate, spindle, nut, valve head with stuffing box incl necessary PTFE gland packing, nuts, bolts, washers, gland bolts, rubbers gaskets etc complete all as specified and as directed. Note: (i) SS spindle,SS nuts shall be measured and paid separately under respective items. (ii) Nuts, bolts & washers wherever required new shall be measured and paid separately under respective item. (iii) PTFE gland packing and Rubber gasket shall be inclusive of the quoted rate of this item.

Supply and fix SS spindle for sluice valve class PN 1.6/ 1.0, 80 mm to 150 mm bore

Supply and fix E54SS spindle for sluice valve class PN 1.6/ 1.0, 200 mm to 300 mm bore

Supply and fix SS nut suitably threaded internally as per spindle thread and to the size of wedge of valve gate for sluice valve 80 mm to 150 mm bore class PN 1.6/ 1.0 complete all as directed.

All as item no.57 above but 200 mm to 300 mm sluice valve

S&F in repair gun metal gate valve with iron wheel head, screwed both ends for iron pipes 15mm bore complete all as specified and directed.Make Zoloto or Equivalent.

All as item no.59 above but 20 mm bore

All as item no.59 above but 25 mm bore

All as item no.59 above but 40 mm bore

All as item no.59 above but 50 mm bore

Supply & fixing in repairs cast Iron swing check non return valve confirming to IS : 5312 (Part I) of 1969, both end flanged with rubber gasket & Nuts, bolts & washersof sizes 100 to150 mm bore. (Note:- Nuts, bolts & washers wherever required new shall be measured in appropriate item as supply only )

All as item no.64 above but 80 mm bore.

Supply & fixing in repairs cast Iron foot valve confirming to IS : 4038 flanged end with rubber gasket, Nuts, bolts & washers of sizes 80 MM bore. (Note:- Nuts, bolts & washers wherever required new shall be measured in appropriate item as supply only )

All as item no.66 above but 65 mm bore

All as item no.66 above but 50 mm bore

Supply and fix Mild steel screw bolts (machine made) with hexagonal heads at one end and screwed the other, each screwed end to be fitted with washers and one hexagonal nut, n exc 10 cm long , 10 to 20 mm dia of neck.

S&F MS mechanical joint with rubber washer, mild steel screw bolts (machine made) with screwed both ends of dia as per flange hole and required length each screwed end to be fitted with washers and one hexagonal nut suitable for bore of pipe 80mm complete all as specified.

All as item no.70 above but 100 mm size.

All as item no.70 above but 150 mm size.

All as item no.70 above but 200 mm size.

All as item no.70 above but 250 mm size.

All as item no.70 above but 300 mm size.

M&L for M & L for PCC (1:5:8) type C5 block masonry over 10 cm in width built in cement mortar (1:6) complete all as specified incl Demolition of unsv precast concrete block walling built in cement morter all as specified and directed.

M&L for cement plaster 10mm thick in CM1:4 on fair faces of brick work or concrete surfaces finished even and fair incl taking down plaster any description, racking out joints, hacking for key, scrubbing down with water complete all as specified.

M&L for PCC 1:3:6 type-C2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete incl necessary form work werever required and incl demolition of Cement Concrete (un-reinforced) of any description and in any position not otherwise specifically provided for, all as specified and directed at site.

M&L for mild steel framed work with ends of bars souldered, welded or reveted or forced into spikes, framed guard bars, ladders, framed balusters, walk ways, railings, gates, frame work of water tank, valvepit and similar work confirming to Fe.290.Gde-E-165 incl painting with one coat of red oxide primer and one coats of anticorrosive black bituminous paint incl dismantling mild steel work of any description not otherwise specially provided for all as specified and directed.

M&L for one coat of synthetic enamel paint to old steel surfaces of any description, incl preparation of surfaces, for area over 10cm in width or girth,not otherwise described as per specified colour code all as specified and directed.

M&L for preparation of plastered or unplastered surfaces of wall and applying one coat of cement based paint of approved tint complete all as specified and directed.

M&L for preparation of plastered or unplastered surfaces of wall and applying two coats of cement based paint of approved tint complete all as specified and directed.

M&L Cement concrete type B-2,1:2;4 ( 40 mm graded stone aggregate ) in sub base 75 mm thick

S&F 80 mm thick machine pressed precast concrete rubber moulded coloured interlocking paver block with coloured cement and pigment any shape and size confirming to IS-15658-2006 M-40 grade laid over 50 mm thick sand cushionining all as directed.

Supply and fix Hot Dipped Galvanized Chain Link Fencing with Zinc Coating, nominal height-2400mm, Pitch-50mm and wire dia 3.15 mm. (approx weight-2.55 Kg /Sqm)

M&L for mild steel work of angle fixed independently for fencing post and others confirming to Gde Fe 410-A incl cutting to dead end length where required, notching, drilling, fitting and/or welding or connecting with bolts and nuts incl dismentling taking down unsv one complete all as specified and directed.

M&L for TMT bars 10mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns hooking ends or as in horizontal bar for fixing in fencing and binding with and including mild steel wire (anealed) not less than 0.9mm dia or securingwith clips complete for support of chain link fencing incl dismentling taking down unsv one all as specified and directed.

Dismantling taking out complete pump of any type, capacity 5 HP to 15 HP of different models from foundation including dismentling suction and delivery pipe connection from pump , carrying to wksp & back and repair/overhauling complete and reassemble and fixing to original position after repair/overhauling with nuts, bolts, washers, pipe connection complete including testing, commissioning all as specified and directed.( Note-1.spares required for the repairs will be measured and paid under respective items . 2. Small items such as gaskets, Nuts,bolts and washers,screws, consumable like grease etc will be inclusive of quoted rates.)

Ball Bearing, (DE).

Ball Bearing (NDE).

Impeller.

Pump Shaft.

Lantern Ring.

Mechanical Seal.

Water Deflector.

Sleeve.

Key Impeller.

Gland Packing.

Dismantling taking out Induction motor 05 Hp to15 HP from foundation by removing electric connection, coupling carefully and carrying to wksp & back for repair /rewinding complete and reassemble and fixing to original position after repair/overhauling with nuts, bolts, washers, pipe connection and cable connection complete including testing, commissioning, proper alignment all as specified and directed.

M&L for complete rewinding of motor any type after cutting, taking out old damaged winding from stator core, cleaning of slots, providing proper insulating materials/lock strip in the slots, rewinding with existing size of super enamelled coper wire, required binding, bonding, insulation, varnishing and drying and proper testing after rewinding for the following sizes of motor capacity 05 HP to 7.5 HP

M&L for complete rewinding of motor any type after cutting, taking out old damaged winding from stator core, cleaning of slots, providing proper insulating materials/lock strip in the slots, rewinding with existing size of super enamelled coper wire, required binding, bonding, insulation, varnishing and drying and proper testing after rewinding for the following sizes of motor capacity 10 HP to 15 HP

Repair/maintenance/overhauling in situ of Pump starter panel by dismantling taking out old damaged panel wiring, replacement of Contactor, relays, Timer, Push buttion, single phase preventor, voltmeter, ammeter, LED indicator and other miscellenious items as required and testing complete after completion of work. Note: spares required for the repairs will be measured and paid under respective items.

S&F star delta starter suitable for electric motorof capacity 10 to 15 HP

AC Contactor, 3 pole, 3 ph, 415V, AC, 50Hz, Type- ML-2 to ML-5 , Make- L&T, or equivelent of equivelent of Schneider/ABB/C&S

AC side mounting add on aux contact block for contactor Make- L&T, or equivelent of Schneider/ABB/C&S

AC front add on aux contact block Make- L&T, or equivelent of Schneider/ABB/C&S

Thermal overload relays, relay range 9 amp to 15 amps as applicable, Make-L&T or equivelent of Schneider/ABB/Crompton/C&S

Electronic Timer, 3 - 30 Sec 415V Make- L&T, or equivelent of Schneider/C&S/Minilac

Motor protection relay, O/L range 1.2 amps, Make-L&T or equivelent of Schneider/ABB/Crompton/C&S

Single phase preventor relay, Make- L&T or equivelent of Schneider/ABB/C&S /Minilac

LED indicator R-Y-B

Starter Push button Red/green

Supply and replacement of submerisible flat copper cable conductor 3 core 10 Sqmm 1100 volts grade complete all as sppecified and directed by Engineer in charge. Make Finolex/National/CCI

Repair/Maint of unserviceble submersible pump of 15 HP capacity by lifting from UG sump and dismantling and strip opening of 3 phase 415volts,AC submersible pump set,transporting the pumping set to workshop for repair including replacement of unserviceable parts of pump such as GM impeller, neck ring, bowl assebly, bushes , coupling, lock, sand cap , CI intermediate bowl, S/S pump shaft etc including testing at site on full load complete all as sepecified and directed by Engr in charge. NOTE :- I. The defective parts such as pump shaft, impellor, neckring, coupling, lock ,gun metal bushes, sand cap etc will be measured and paid separately under respective items. II. Rates for repair,servicing,complete checking, machine work what ever is reqd cutting,grinding,polishing and transportation from site to workshop and back are deemed to be included in the quoted rates.III. Delivery pipe of pump is GI pipe and Quoted Rates shall be inclusive of removing and refixing of GI pipe.

Supply and fix Pump shaft stainless steel sleeve suitable size 15HP submersibale pump

Supply and fix Impeller bronze/gun metal of suitable for 15HP submersible pumps.

Supply and fix Neck ring gun metal of suitable size for 15HP

Supply and fix Gun metal bowl bushes suitable for submersible pump of 15 HP.

Supply and fix Cast iron suction /discharge case bowl of suitable size for 15HP

Supply and fix Sand cap of suitable size from 15HP

Supply and fix Cast iron inter mediate bowl of suitable size from 15HP.

Repair/servicing of unserviceble submersible motor of 15HP, 3 phase 415volts by lifting from UG sump,transporting to workshop,dismantling and strip opening re-winding with PVC insulated supperior quality water proof copper winding wire of suitable size/gauge and nos of turns including replacement of insulating materials incl new submersible cable of suitable size for connection from motor to outside upto a length of 1.5 mtrs and reassembling including testing at site on full load complete all as sepecified and directed by Engr in charge. NOTE :- I. The defective parts such as Thrust plate/bearing/sleev/pad/bush end etc will be measured and paid separately under relevant items as. II. Rates for repair,servicing,complete checking, machine work what ever is reqd cutting,grinding etc complete and transportation from site to workshop and backs are deemed to be included in the quoted rate.

Supply and replacement of thrust plate suitable for submersible motor 15 HP

Supply and replacement of thrust pad suitable for submersible motor 15 HP

Supply and replacement of bearing suitable for submersible motor 15 HP

Supply and replacement of bush suitable for submersible motor 15 HP

Cleaning of MES water supply installations / campus at MG Road approx area 300 sqm, other than considered in outsourcing by surface dressing or trimming of natural ground to remove small unequalities n.exc 15 cm deep ( including removing vegetation / shrubs / brush wood / under-growth ), cleaning of drains & carrying away the rubbish to a distance of n.exc 50 mtr away complete at an interval of every 30 days complete all as directed by Engineer in Charge.

All as per item No 127 above but at SFQ approx area 700 sqm

All as per item No 127 above but at CAFVD approx area 1200 sqm

All as per item No 127 above but at Sarvatra Vihar approx area 1100 sqm

All as per item No 127 above but at Charch Rd approx area 120 sqm

All as per item No 127 above but at Nirikshan Vihar approx area 1450 sqm

All as per item No 127 above but at KKD Line approx area 2000 sqm

All as per item No 127 above but at EH Road approx area 2500 sqm

All as per item No 127 above but at EME Line approx area 600 sqm

JP ENTERPRISES

M/S VR Construction Services