Widening of main gate and making of security room in CSIR-NML Housing Complex Agrico

Amount

Dismantling doors, windows shutters including chowkhats,architrave, holdfasts,etc. complete and stacking disposal of material as per direction of EIC. Of area 3sq. Metres and below .

Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres as per direction of EIC Nominal Concrete Mix 1 :3:6 or richer mix.

Demolishing reinforced cemenrt concrete manually / by mechanical means including stacking of steel bars and disposal of unserviceable material with in 50 metre lead as per direction of EIC.

Demolishing Brick work in cement mortar manually/ by mechanical means including stackng of serviceable material and disposal of unserviceable material with in 50 metre lead as per direction of EIC. In Cement Mortar.

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground with in 50 metre lead.

Dismantling GI pipes (External work) including excavation and refilling trenches after taking out the pipes , manually /by mechanical means including stacking of pipes within 50 metre lead as per direction of Engineer In Charge. 15 mm to upto 40mm nominal bore

Dismantling steel work in single section including dismembering and stacking within 50 metreleadin:Channels,angles,tees and flats .

Supply Chemical emulsion in sealed containsers including delivery as specified.Chlorpyriphos/Lindane emiulsifiable concentrate of 20 % .

Supplying and filling plinth with sand under floor including watering, ramming, consolidating and dressing,complete.

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains(not exceding 1.5m in width or 10 sqm on plan) including dressing of sides and ramming of bottom,lift up to1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within alead of 50 m.All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, side of foundations etc. in layer not exceeding 20 ems in depth: consolidating each deposited layer by ramming and watering, lead upto 50m and lift uoto 1.5m.

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work uoto plinth level. 1:2:4 (1cement:2coarse sand: 4graded stone aggregate 20mm nominal size.)

Providing and laying in position specified grade of reinforced cement concrete,excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

RCC work in walls, beam suspended floors, roofs having slop up to 15 degree landing , balconies, shelves, chajja, lintels, bands, plain window sill ,stair case and spiral stair cases above plingth level up to floor five level excluding cost of centering,shuttering,finishing and reinforcement. 1:1.5:3 (1cement:1.5coarse sand: 3graded stone aggregate 20mm nominal size.)

Steel reinforcement for RCC work including straightening, cutting bending, placing in position and binding all complete above plinth level.Thermo- Mechanically Treated Bars Fe -500 D or more

Centring and shuttering including strutting,propping,etc. and removal of form for: Foundation,footings,bases of columns,etc.

Centring and shuttering including strutting,propping,etc. and removal of form for: Suspended floor ,roof ,landing , shelves, beams, columns balconies,etc.

Centring and shuttering including strutting,propping,etc. and removal of form for: Weather Shade, chajjas,corbels,etc. including edges

Brick work with common brunt clay F.P.S (Non Modular ) bricks of class designation 7.5 in foundation and plingth: in Cement mortar 1:4 (1cement : 4 coarse sand)

Brick work with common brunt clays F.P.S (non modular) brick of class designation7.5 in super structure above plingth level upto floor V level in all shapes and sizein cement mortar 1:4 ( 1Cement : 4 Coarse Sand).

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

P/F MS grill of required pattern in frames of windows etc. with M.S flats ,square or round bars etc.including priming coat with approved steel primer all complete.Fixed to openning /wooden frame with rawl plugs screws etc.

Providing & fixing 18 mm thick gang saw cut mirror polished Granite machine cut for kitchen plate form vanity counters,window sill, facias and similer location of requered size of approved shade , colour and texture laid over 20 mm thick base cement morter 1:4 with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edge to give high gloss finish etc. complete at all levels----Granite of any any colour and shade. Area of Slab over 0.50 sqm

Extra for fixing marble/granite stone over and above corresponding basic item, in facia and drops of width upto 150mm with epoxy resin based adhesive includina clean etc. complete

P/F 1st quality ceramic glazed wall tiles conforming to IS : 15622 of (thickness to be specified by manufacturer) of approved make in all colours, shadess except burgundy, bootle green, black of any size as approved by Engineer in change, in skirting, risers of steps and dados over 12mm thick bed of Cement morter 1:3 (1cement: 3 Coarse sand) and jointing with gray cement slurry @ 3.3 kg per sqm incl. pointing with white cament mixed with pigment of matching shade complete.

Cement concrete flooring 1 :2:4 finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete. 1 :2:4 with floating coat of neat cement punning. 40mm thick with 20 mm nominal size stone aggregate.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of Size of Tile 600 x 600 mm

12mm cement plaster of mix. 1:4 (1cement : 4 coarse sand)

15mm cement plaster on rough side. 1:4 (1cement : 4 coarse sand)

6 mm cement plaster for ceiling of mix 1:3. (1cement : 3 fine sand)

Neat cement punning.

Finishing walls with Acrylic Smooth exterior paint of required shade . Old Work (Two or more coat applied @ 1.67 ltr/10sqm) on existing cement paint surface.

Providing and applying plaster of paris putty of 2mm thickness over plastered surface to prepare the surface even and smooth .

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface. Water thinnable cement primer

Painting with aluminium paint of approed brand and manufecture to give an even shade: Two or more coats on new work .

Applying priming coat with ready mix pink or grey primer of approved brand and manufecture on wood ( hard and soft wood) on wood work.

Painting with synthetic enamel paint of approved brand andmanufacture to give an even shade :Two or more coats on new work

Providing and fixing on wall face unplasticised Rigid PVC rain water conforming to IS-13592 Type A, including jointing with seal ring conforming to IS: 5382, 75 mm dia

Providing and fixing on wall face unplasticised Rigid PVC rain water conforming to IS-13592 Type A, including jointing with seal ring conforming to IS: 5382, 110mm dia

Providing and fixing PVC moulded fittings/accessories for unplasticised Rigid PVC pipes rain water pipes conforming to IS:13592 type A including jointing with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion . Bend 87.5 degree size 75 mm bend.

Providing and fixing PVC moulded fittings/accessories for unplasticised Rigid PVC pipes rain water pipes conforming to IS:13592 type A including jointing with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion . Bend 87.5 degreesize 110 mm bend.

Providing and fixing PVC moulded fittings/accessories for unplasticised Rigid PVC pipes rain water pipes conforming to IS:13592 type A including jointing with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion .Shoe (Plain) size 110 mm .

Providing & fixing anodised aluminium work for doors, windows, ventilators, and partion with extruded built up standard tubular sections/ Zsection and other section of approved make conforming to IS 733 and IS 1285,fixed with dash fasteners of required dia and size , including necessary filling up the gaps at junction ,i.e at top , bottom and sides with required EPDM rubber /neropene gasket etc. Aluminium section shall be smooth ,rust free,straight,mitred and jointed mechanically whereever requred including cleat angle, aluminum snap beading for glazing/panelling, C.P brass /stainless steel screw, all complete as per architectural drawing and the direction of Engineer in Charge(Glazing and panelling to be paid for separately):For fixed Portion Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Providing & fixing anodised aluminium work for doors, windows, ventilators, and partion with extruded built up standard tubular sections/ Zsection and other section of approved make conforming to IS 733 and IS 1285,fixed with dash fasteners of required dia and size , including necessary filling up the gaps at junction ,i.e at top , bottom and sides with required EPDM rubber /neropene gasket etc. Aluminium section shall be smooth ,rust free,straight,mitred and jointed mechanically whereever requred including cleat angle, aluminum snap beading for glazing/panelling, C.P brass /stainless steel screw, all complete as per architectural drawing and the direction of Engineer in Charge(Glazing and panelling to be paid for separately):For shutter of doors,window & ventilators including providing and fixing hinges /pivot and making provision for fixing of fitting wherever required including the cost of EPDM rubber /neropane gasket required (Fittings shall be paid for separatly ) Anodised Aluminium(anodised transparent or dyed to required shade according to IS :1868, Minimum anodic coating of grade AC 15)

Providing and fixing glazing in aluminium door, window, ventilator shutters: With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per uirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment).

Grading roof for water proofing treatment with cement concrete 1:2:4 (1cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) with waterproofing material.

Providing & laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1cement: 2 fine sand) including testing of joints,etc. complete.150 mm dia R.C.C pipe

Providing and fixing white vitreous china water closet approved make. Orissa pattern WC pan 580 x 440mm

P/F GI union in GI pipe including cutting and threading the pipe and making long screws etc. complete (New Work)15mm NB

P/F GI union in GI pipe including cutting and threading the pipe and making long screws etc. complete (New Work)20mm NB

P/F GI union in GI pipe including cutting and threading the pipe and making long screws etc. complete (New Work)25mm NB

Providing and fixing G.I. pipes complete with G.I. fittings and clamps i/c cutting and making good the wall etc.20 mm dia NB

Providing and fixing G.I. pipes complete with G.I. fittings and clamps i/c cutting and making good the wall etc.25mm dia NB

Providing and fixing G.I. pipes complete with G.I. fittings and clamps i/c making good the walls etc. Concealed pipe, including painting with anti corrosive bitumastic paint,cutting chases and making good the wall:15 mm dia NB

P/F C.P brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms 15mm nominal bore

P/F C.P brass stop cock (concealed) of standrad design and of approved make conforming to IS 8931, 15mm nominal bore

Disposal of building rubbish/ malba/ similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Enginineer-in-charge, beeyound 50 m initial lead for all leads including all lifts involved.

Providing & Fixing of ISI marked flush door conforming to to IS 2202(Part-1) non decorative type core of block board construction with frame of 1st class hard wood and well matched mmercial 3 ply veneering with vertical grains or cross bands and face veneers on both face of shutters, : 25 mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. Piano hinges IS : 3818 marked with necessary screws bright finished M.S. Piano hinges IS : 3818 marked with necessary screws

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931-15mm nominal bore

Providing and fixing bright finished brass tower bolts (barrel type) with necessary:250x10 mmscrews etc. complete :

Providing and fixing bright finished brass tower bolts (barrel type) with necessary:250x10 mmscrews etc. complete :150x10 mm

Providing and fixing bright finished brass door latch with necessary screws etc.300x16x5 mm complete :

Providing and fixing bright finished brass door latch with necessary screws etc.complete :250x16x5 mm

Providing and fixing bright finished brass handles with screws etc. complete:125 mm

Extra for providing and mixing hardening compound of approved quality as per manufacturer's specification in cement concrete.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade. Old work (two or more coats) including removing, scrapping, sand papering and preparing the surface smooth including necessary repairs with plaster of paris where necessary, etc complete.

Supply of white vitreous china wash basin of approved brand:Flat back wash basin of size 550 x 400mm.

Supply of 600 x 450mm bevelled edge mirror of superior glass (of approved quality) with 6mm thick hard board ground with C.P. brass screws and washers .

Supply of P.V.C low level flushing cistern with manually controlled device (handle lever) conforming to IS:7231 with all fittings and fixtures including .10ltr capacity -white.

Supply of Stainless steel tower bolts,with necessary screws etc. Size 200x10mm

Supply of Stainless steel handle of approved quality and design with necessary screw etc. complete. Size-150mm.

M/S.A.B.CONSTRUCTION