SPECIAL REPAIR TO BUILDING NO. P-20 (MI ROOM) , P-8A(AIRMEN MESS), P-10(AIRMEN BILLET) , P-06(SNCOs MESS) AND E/M INSTALLATION IN DOMESTIC AREA AT MCC AF STN BASANT NAGAR UNDER GE(AF) PALAM DELHI CANTT-10

Amount

Taking down chowkhats or frame area n exc. 1.5 sqm each but with shutters (without taking off shutters from the frames) complete all as specified and directed.

All as per ser. item no. 1 above but area exceeding 1.5 Sqm but not exc 4.00 Sqm each complete all as specified and directed.

Taking down shutters of any description area exceeding 1 sqm and not exceeding 2 sqm each complete all as specified and directed.

Demolition of concrete in ground floors and pavings n.exc 15 cm thickness (below or above ground level) complete all as specified and directed.

Dismantling structural steel work including doors,gates but excluding framed truss etc.complete all as specified and directed.

M & L for removing loose, disturbed or disintegrated old concrete surfaces of RCC beam, column, lintel,slab,chajjas, railing etc, cleaning thoroughly exposed reinforcement, by sand blasting using suitable pump as directed by the GE, preparing exposed concrete surfaces to receive guniting, applying one coat of anti corrosive paint to the exposed reinforcement, supply and fix welded wire mesh of size 100 x 100 mm of 3 mm dia wire, weight not less than 1.37 Kg/Sqm & binding with 22 gauge mild steel (annealed) binding wire to reinforcement and applying pressure guniting in cement mortar 1:3, average 30mm to 50mm thickness and thereafter rendering 10 mm thick plaster in cement mortar 1:3, mixed with water proofing compound @2% by weight of cement and finishing the surfaces even and smooth without using extra cement to match with the existing surfaces, removing the debris outside MD land including material and labour for necessary scaffolding and formwork (G+3 storeys) and safety arrangement for guniting work, complete all as specified and directed. (Note :- The finish of the surfaces to be matched with the existing surface. WPC shall be measured & paid separately as supply only).

Taking down cement plaster or cement lime plaster on brick or stone walls ,etc. including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and directed.

M&L for 10mm thick plaster on fair faces of brick work or concrete surfaces in cement mortar 1:3 in ceilings, to be finished even and smooth without using extra cement complete all as specified and directed.

M&L for 15 mm thick cement plaster on fair faces of brick work or concrete surfaces in cement mortar 1:6, to be finished even and smooth without using extra cement complete all as specified and directed.

M&L for 15 mm thick cement plaster on fair faces of brick work or concrete surfaces in cement mortar 1:4, to be finished even and fair with water proofing compound by weight as per manufacturer's instructions (WPC will be paid separately) including necessary scaffolding up to (G+3 storey) complete all as specified and directed.

S&F factory made PVC door frame of size 50mmx47mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, supplying & fixing in opening as per specification and drawing complete all as specified and directed.

Supply and fixing for factory made Solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tube for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC 'C' channel having PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side and as gap insert for top rail and bottom rail panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading, and jointed together with solvent cement, supplying and fixing in the frame at site as per specification and drawing complete all as specified and directed.

S&F 12 mm thick entrance glass door at alley way with one way visibility , locking arrangement necessary unit insignia embossed (unit symbol )on glass as per sample approved by user unit with all fittings and fixtures complete of and glass partition above shutter to roof level including fancy type handle , locking arrangement , springs , door closer and aluminium frame work including suitable beading and with necessary electrical fittings etc. complete all as specified and directed .Note: Quoted rate shall be inclusive of aluminium sections

S&F rolled mild steel grade Fe-290 Gde-E-165 quality-A as in Framed work as in doors or gates of angle or other section gates of with gusset plates, rails, cladding, chowkhats/frame or like etc. including welding hold fast, hinges complete all as specified and as directed.

S&F 35 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

M&L for 2nd class hard wood factory made 35mm thick glazed and skeleton shutters, open rebated and prepared for door to receive glass, gauze, etc., edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass/wire mesh etc. size of members of shutter as specified in SSR Part I, Section 8, clause 8.24 (a) with sash bar complete all as specified and as directed.

S& F Powder coated aluminium frame for doors,windows, ventilators with one or more rebates including joining cleat for fixing etc. (minimum thickness of powder coating 50 micron) complete all as specified and directed.

S&F Powder coated aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips,rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) (Thickness of powder coating not less than 50 micron) complete all as specified and directed.

S&F Window/Ventilator section of frame 72 x 55 mm fixed to wall or concrete surface with MS hold fast (30 x 5 mm section) 150 mm long made of galvanised steel powder coated and section of shutter 47 x 20 mm, mulion section 72 x 50 mm (base steel as per IS 513 'D' quality galvanised as per IS 277 with zinc of 120 gms/Sqm) glazed or gauzed and wire gauze shutter (Double door shutter) with total coated thickness of 0.60 mm including powder coated grill/guard bars made of square bars 10 mm dia at 150 mm c/c horizontal spacing fixed in MS flat frame (30 x 5 mm) fixed to windows frame with screws, including 4 to 5 mm thick sheet glass, 0.36 mm stainless steel wire cloth with 1.40 mm aperture necessary fittings and all builders hardware such as handles, tower bolts & stays etc. complete all as specified and directed. Type-4000 series Ref drg No CEAF/STD-191/2014 Sheet 1/2&2/2.

S&F Powder coated Aluminium three track sliding type glazed window shutter with 5 mm thick plain sheet glass fixed open track section 100x38x1.5mm having three track (two of glass & one of stainless steel wire cloth of 0.36mm nominal dia of wire and average width of aperture 1.40mm) with members of window shutters of section 38x12x1.5mm and other standard sliding section including all necessary fiber wheel rollers ,suitable handles to facilitate sliding and all necessary jointing cleats glazing clips rubber packing, aluminium snap beading etc. complete all as specified and directed (Aluminium section shall be make of Jindal / Hindalco /Indal ) and Make of glass shall be MODI/ATUL/Saint Gobain Note : Cost of other consumables required for the item shall be deemed to be included in the quoted rate (Glass panes /wire Cloth / lock /handle)

S&F aluminum anodised grill DG-102 (10mmx5.2mm) of Decorative grill or equivalent fixed with 'F' Section size not less than 20.60x15.20x1.5mm thick of approved make complete all as specified and directed Note : Minimum thickness of anodising shall be 15 microns.

Cutting holes in brick walls, built in cement mortar or cement lime mortar, exc half brick but not exc one brick, for inserting hold fasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B1 as required complete all as specified and directed.

S&F for clamps; hold fast; bands, straps, supports or stays for galvanised plain mild steel wire including bolts, rainwater, ventilating pipe and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

S&F for butt hinges, stainless steel, ISI Marked 100mm size, complete all as specified and directed.

S&F for MS butt hinges 100mm size, cold rolled, medium weight fixed with screws to wooden frames or welding to steel frames etc. complete all as specified and directed.

S&F for aluminium anodized, barrel tower bolts of extruded section, length of bolt 150mm long complete all as specified and directed.

S&F for extruded aluminium alloy handles, fabricated type, anodised, 125 mm size complete all as specified and directed.

S&F for extruded aluminium alloy handles, fabricated type, anodised,100 mm size complete all as specified and directed.

S&F for aluminium sliding door bolt, 250 mm long, with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections or cast aluminium alloy including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.

S & F 19mm thick prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws as in cup boards, shelves and pelmet boxes etc. and including dismantling boarding, any description, fixed with screws complete all as specified and directed.

S&F for sheet glass of size 4mm thick, ordinary quality fixing to wooden door/aluminium window shutters in any position with new beads/ steel section as required for securing complete all as specified and directed.

S&F for stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed.

S&F in repair 20mm dia aluminium Drapery rod, coated finish including teak wood brackets & end knob as required with teak wooden curtain rings complete all as specified and directed.

Demolition of mud in roofs, any thickness, including plastering/ concrete and leeping (whether full thickness removed or only a part there of) and including Taking down existing tarfelt/water proofing membrane and disposing off debris outside MOD land complete all as specified and directed.

Demolition of cement concrete from sunken floor,roofs,floors (other than ground floors) hacking of surfaces after cleaning with wire brush (floor and adjoining walls) and disposing off debris outside MOD land complete all as specified and directed.

Demolition of reinforced concrete roofs, floors (other than ground floors), beams, staircases, landing,chajjas and similar suspended work complete all as specified and directed.

M&L for providing reinforced cement concrete (nominal mix) using 20mm graded aggregate (type B-1 1:2:4) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.

M&L for Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc. 20 cm wide complete all as specified and directed.

M&L for TMT or deformed bar 10mm dia, cut to length, bent to shape required including cranking bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire(annealed) not less than 0.9 mm dia.or securing with clips complete all as specified and directed.

All as per ser. item no. 40 above but 5 to 10mm dia bars in stirrups, spacers and binders complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Demolition of stone slabs and tiles laid bedded and pointed in any mortar of any description or thickness in floors , aprons etc complete all as specified and directed.

M&L for joint free non skid coloured ceramic tiles, 7 to 8mm thick (square or rectangular) area of each tile n.exc. 0.11sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces, laid over & including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L for joint free coloured glazed ceramic tiles in vertical surfaces 300x200x7mm/ 450x300x7mm thick set and jointed in cement slurry and pointed in white or coloured cement to match, laid over & including 15mm thick cement rendering in cement mortar 1:4 complete all as specified and directed.

M&L for cement concrete type E2 1:5:10 (40mm graded crushed stone aggregate) in foundations, mass concrete and filling in sunken floor etc complete all as specified and directed

M & L for special treatment for sunken portion of WCs/Bath & toilet etc. executed in following stages : Stage 1: Providing 15mm thick plaster in CM 1:3 mixed with water proofing chemical of Dr.Fixit or Shalicrete 'R' of STP Ltd or equivalent in the proportion/quantity all as per manufacturer's instructions. State 2 : Primer-Mix Tarfelt LM of STP Ltd (diluted with water in ratio 1:1) or equivalent @ 250 gms/sqm and apply the primer on the plastered surfaces. Stage 3 : Application of 1st coat of Tarfelt LM of STP Ltd (without dilution with water) or equivalent @ 1Kg/Sqm by brush all as per manufacturer’s instructions. Stage 4: Laying fiber glass cloth (weight not less than 50gram/ Sqm) over the 1st coat while the coated surface is still sticky. Stage 5: After 6 to 7 hours interval, apply second coat i.e. final coat of Tarfet LM of STP Ltd (without Dilution with water) or equivalent @ 1kg/ Sqm by brush as per manufacturer's instructions. Stage 6: Providing 10mm thick protective plaster in CM 1:3 mixed with STP No. 1 or equivalent @ 250ml/50 Kg cement all as per manufacturer's instructions. Stage 7: Carryout ponding test for 48 hours to ensure water tightness of repaired sunken portion. NOTES :(i) Mode of measurement: Actual area treated (floor and adjoining walls) will be measured and paid .

M&L Granite (of any type) tiles 20mm thick in floor machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including 20mm thick CM 1:6 screed bed for laying floor finishes and cutting and polishing complete all as specified and as directed.

M&L 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over screed bed or bedding layer of mortar 15 mm in cement mortar 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M & L for machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete laid over 15mm thick screed bed in CM 1:4 complete all as specified and directed.

M&L for vitrified tiles coloured, light shade 10 mm thick, area of each tile n.exc. 0.36 Sqm in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces, laid over & including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

All as per ser. item no. 51 above but as in skirting /dado laid over 10 mm thick bedding layer of CM 1:4 complete all as specified and directed

Demolition of brick work built in cement mortar, including all quoins, arches, pillars etc. of any description including removing debries from site complete all as specified and directed.

M&L for brick work with sub class `B' bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

Supply only Integral Water Proofing compound complete all as specified and directed. Make : Dr. Fixit or equivalent

M&L for preparing plastered or unplastered new surfaces on ceilings including brooming down or steel wire brushing, scraping down and applying three coats of white wash complete all as specified and directed.

M&L for preparing old surfaces on ceilings including brooming down or steel wire brushing, scraping down and applying two coats of white wash complete all as specified and directed.

M&L for preparing plastered or unplastered new surfaces on walls including brooming down or steel wire brushing, scraping down and applying two coats of distemper oil emulsion over one coat of alkalic resistant primer complete all as specified and directed.

M&L for complete removal of existing treatment of old plastered surfaces on walls including brooming down or steel wire brushing, scraping down and applying two coats of distemper oil emulsion over one coat of alkalic resistant primer complete all as specified and directed.

M& L for preparation of new plaster surface of walls ,chajjas, soffits & beam including necessary scaffolding and applying two coats of cement base paint over one coat of chalk whiting primer complete all as specified and directed.

M& L for complete removal of existing surface of walls ,chajjas, soffits & beam including necessary scaffolding and applying and applying two coats of cement base paint over one coat of chalk whiting primer complete all as specified and directed.

M& L for preparation of new plaster surface of walls ,chajjas, soffits & beam including necessary scaffolding and applying two coats of acrylic smooth exterior paint of required shade 1.43ltr/10sqm over a coat of exterior primer 2.20kg/sqm (brand Apex Ultima manufactured by Asian or Brand weather coat manufactured by Berger or equivalent in shalimar as approved by GE) as per manufacturer's instructions complete all as specified and directed.

M& L for complete removal of existing surface of walls ,chajjas, soffits & beam including necessary scaffolding and applying two coats of acrylic smooth exterior paint of required shade 1.43ltr/10sqm over a coat of exterior primer 2.20kg/10sqm (brand Apex Ultima manufactured by Asian or Brand weather coat manufactured by Berger or equivalent as approved by GE) as per manufacturer's instructions complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of wood of any description not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint over & including one coat of pink primer complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of steel of any description not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint over & including one coat of red oxide primer complete all as specified and directed.

M&L for preparation of old painted surfaces of wood and wood based material of any description, not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed

M&L for provision 1 mm thick wall care putty applying on walls for smooth finish complete all as specified & directed .

M&L for provision 1 mm thick wall care putty applying on ceiling for smooth finish complete all as specified & directed .

M&L for 75 mm thick cement concrete type C1, 1:3:6 (using 20 mm graded aggregate) as in plinth protections, to be finished even and smooth without using extra cement complete including use of necessary form work complete all as specified and directed.

M&L for providing cement concrete 1:2:4, type B-0, using 12.5 mm graded stone aggregate, 50mm (average thick) as in roof padding to maintain slope etc. complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of plastered/concrete surfaces of roof and applying the under mentioned course of roof treatment complete all as specified and directed by Engineer-in-Charge.:- (a) Plastering 10mm thick in cement mortar 1:4 on concrete surfaces using WPC @3% by weight of cement, finished even and smooth (b) Surface shall be thoroughly wire brushed, cleaned, washed, dried up properly and apply evenly a bituminous primer coat conforming to IS @0.4 ltr /Sqm over concrete / plastered roof surface. (c) Laying of 3mm thick APP membrane sheet (min weight 3 Kg/Sqm) consisting of a core of 160 gms/Sqm polyester non woven fabric mat protected on both sides with a high quality polymeric asphaltic mix again protected with thermo fusible HMHDPE FILM on dried primed surface by torch application method. APP membrane will normally be laid in length at right angle to the direction of slope. The overlap shall be minimum 100mm on longitudinal direction and 150mm on the transverse direction including cuttings, grooves etc. (d) Membrane bonded completely to the substrate & the over laps are then scaled/fused by flame.

M&L for cement concrete tiles 20cm x 20cm x 20mm thick, machine pressed, set & pointed in neat cement slurry in floor with grey cement and no pigment and cut and polished on roof over and including 15 mm thick screed bed in CM 1:4 complete all as specified and directed.

Taking up or down 15mm steel tubing (bore of pipe in 15mm) and connections in walls, ceilings, floors, etc including cleaning for refixing or removal to store complete all as specified and directed.

Taking up or down 20mm steel tubing and connections in walls, ceilings, floors, etc including cleaning for refixing or removal to store complete all as specified and directed

M&L for GI tubing, 15mm bore `medium grade` with all fittings and fixed complete to walls and ceilings or laid in floors etc complete all as specified and directed

M&L for GI tubing, 20mm bore `medium grade` with all fittings and fixed complete to walls and ceilings or laid in floors etc complete all as specified and directed

Re-fixing old steel tubing, bore of pipe in 15mm and connections including connections in new or old position (walls, ceiling, floors, etc) complete all as specified and directed

Re-fixing old steel tubing, bore of pipe in 20mm and connections including connections in new or old position (walls, ceiling, floors, etc) complete all as specified and directed

Dismantling water tanks exc. 500 & n exc. 1000 capacity in litres and removing to store complete all as specified and directed

S&F for 1000 ltr rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), hoisted and fixed in position complete all as specified and directed.

S&F for ball brass valves, 20 mm bore, high pressure with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

S&F for gunmetal, globe or gate valves, 20 mm bore, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

Taking down AC, PVC pipes of 100/110mm dia of any description including all fittings complete all as specified and directed.

Taking down CI pipes of 100/110mm dia of any description including all fittings complete all as specified and directed.

All as per ser.item no. 84 above but 75/80 mm dia pipes complete all as specified and directed

Supply and Fixing 110mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls including suitable clamps at one meter of interval complete all as specified and directed

S&F for PVC (SWR) bends of any radius, suitable for 110mm dia PVC pipes fixed complete all as specified and directed.

S&F for 75mm bore cast iron waste and vent pipe in any length with or without ears, fixed to walls including suitable clamps after every one meter of interval with cement joints fixed to wall complete all as specified and directed

S&F for 100mm bore cast iron waste and vent pipe in any length with or without ears, fixed to walls with cement joints fixed to wall including suitable clamps after every one meter of interval complete all as specified and directed

S&F for CI 100mm bends with access door complete all as specified and directed

S&F for CI 100mm single branch piece with access door complete all as specified and directed.

S&F for CI 75mm bends with access door complete all as specified and directed.

S&F for cast iron cowls 100 mm size complete all as specified and directed.

M&L in repairs for cast iron Nahani trap/floor trap with CP grating including jointing with cement joint to waste pipe of 75mm dia fixed in cement concrete type B-1(1:2:4) complete all as specified and directed.

S&F in repairs for Cast Iron 'P' Trap 100mm bore complete all as specified and directed

Supply and Fixing in repairs, salt glazed stone ware gully traps 150x150mm size square mouthed, type ‘P’ including CI cover complete all as specified and directed

S&F in repairs vitreous china squatting pan, 'Orissa' pattern, size 580 X 440mm white with integral foot rests, including connection to drain or outgoing pipe and to flushing pipe, anti-syphonage pipe joint and to socket or stopper, including flush pipe all fittings etc. complete all as specified and directed

S&F in repairs Vitreous china wash down water closet pan “Pedestal Pattern” coloured with WC seat cover coloured closed pattern with flat bottom and mild steel chromium plated or aluminized hinging device including PVC flush pipe and joints etc. and connection to drain, flushing, pipe, anti- syphonage pipe, and fixing arrangements with fixing bolts etc ,complete all as specified and directed

Supply and fixing in repairs low level flushing cistern 10 ltrs capacity, and connections to pies an fixing of chain and pull, or lever, if any PVC valve less, syphonic action type, flushing cistern, low level, white,with inlet, including brackets complete all as specified and directed.

S&F in repairs vitreous china ware Wash Hand Basin, white, flat back of size 550 x 400 mm including brackets, cutting for and pinning in ends of brackets or erecting stand including brass CP union/waste fitting of 32mm dia and discharge pipe of 32mm dia PVC of 1.0 m length including one CP pillar tap, cast copper alloy with all fittings etc. complete all as specified and directed

S&F Hand Shower (Health faucet) with 1.00 metre long Easy flex tube in chrome finish & wall Hook, Cat No ALD-CHR-565 of JAQUAR or equivalent of make MARC or KOHLER as approved by the GE complete all as specified and directed

S&Fin repairs vitreous china, counter wash hand basin oval shape size( 420x420mm x135 mm) fixed on granite counter down slab including brass chromium plated full threaded waste coupling with grating 32mm dia PVC waste pipe complete all as specified and directed. (Note: Granite slab, RCC plat form, brick wall support etc shall be measured and paid separately)

S&F in repair 6mm thick glass mirror of size 750x600mm all edges/ border proper moulding complete all as specified and directed

S&F in repairs vitreous china urinals half stall type white or coloured with grating and union for discharge pipe etc. complete all as specified and directed.

S&F in repairs for PVC connections 15mm size with PTMT nuts of length 600 mm complete all as specified and directed.

Dismantling asbestos cement (corrugated , semi corrugated etc.) sheets in roof coverings complete all as specified and directed

S & F MS steel work in tubular trusses and tubular posts including special shaped washers etc., complete using ERW or induction butt welded tubes confirming to IS 1161- 1979 graded St 240 complete all as specified and directed.

S&F Polycarbonate multiwall Hollow sheet 10mm thick of any colour having UV coating on both sides ,weight 1.70kg/sqm (minimum),tensile strength of 62MPa as in roof covering/cladding to wall, fixed as per manufacturer instructions complete all as specified and directed (Note: Colour shall be approved by GE)

S&F standard aluminium anodized section (minimum thickness of anodizing shall be 15 micron) for fixing Polycarbonate multiwall Hollow sheet with and including EPDM gasket as in roof covering/cladding complete all as specified and directed. (Aluminium section shall be of make Jindal/ Hindalco/ Indalco) Note:- Weight of aluminium sections as per actual or as per IS or as per manufacturer, whichever is less, shall only be considered for payment. Cost of other items / accessories required for entire completion of the work shall be deemed to be included in the quoted rate.

S&F in repairs stop valve (half turn)15 mm dia, cast copper alloy, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or union and fixed, Chromium plated fancy type complete all as specified and directed

S & F in repairs bib tap (half turn)15 mm dia cast copper alloy chromium plated fancy type with crutch or butterfly handle, screwed down,screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F Pillar tap (half turn) 15 mm dia, cast copper alloy, with capstan heads, chromium plated screwed down high pressure, with or without lettered 'Hot' or 'Cold' with screwed shanks and fly nuts, screwed for iron pipe and fixed complete all as specified and directed.

Supply and fixing in repairs brass chromium plated tubular towel rail 20mm dia, D type, 60cm long between flanges complete all as specified and directed.

M&L for 75 mm thick cement concrete type D2, 1:4:8 (using 40 mm graded aggregate) as in sub base, to be finished even and fair complete including use of necessary form work all as specified and directed.

S& F for machine pressed precast concrete interlocking paver block any shape and size,with grey cement and pigment to match, confirming to IS 15658-2006 (latest revised) of 60mm thick M-35 grade laid over 50 mm thick sand cushioning complete all as specified and directed.

M&L for heavy duty tiles of size 600x600x10 mm thick, set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match the colour of the tiles, over and including 15mm thick cement mortar screed bed in CM 1:6, complete all as specified and directed.

Dismantling ceiling board, any size or description, fixed in any position or in any thickness, including cover fillets with nails complete as specified and directed

Providing & Fixing false ceiling at all heights with semi perforated 12mm thick micro tegular edged GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of size 595x595 mm of approved texture, design and patterns having moisture content less than 2% , humidity resistance of 99%, NRC 0.50 TO 0.75 as per IS 8225:1987, Non combustible as per BS 476 (Part 4) -1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanized iron section of 0.33 mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size 15x32 mm of length 3000mm, cross-T of size 15x32 mm of length 1200 mm and secondary intermediate cross -T of size 15x32 mm of length 600mm, suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e. 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1000mm length and L-shape level adjuster of size 85x25x2 mm, Galvanised iron perimeter wall angle of size 24x24x0.40mm of length 3000mm to be fixed on periphery wall/partition with the help of plastic rawl plugs at 450mm center to center and 40mm long dry wall wood screws complete all as specified and directed.

M&L for Solid PVC Wall Lining consisting of 5mm thick prelaminated colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame complete all as specified and directed.

M&L for 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame complete all as specified and directed.

Removing demolished materials etc. (other than spoil) including loading, unloading and stacking etc. and disposing off debris outside MOD land complete all as specified and directed.

Taking down carefully unserviceable copper/aluminium point wiring (light, fan, socket or power)complete including fixture and fitting such as switches, ceiling roses, lamp holder, regulators, sockets, light fittings, wooden terminal boxes, plastic laminated sheet cover, including taking down of DB’s, meter board any type and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed.

Taking down unserviceable sub main wiring with conduits/battens etc complete all as specified and as directed.

M & L for Point wiring with single core PVC insulated but unsheathed 1.5 Sqmm FRLS multistranded copper conductor cable 1100 volts grade IS-694 marked drawn in and including rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked with all conduit fittings and fixing accessories including pressed steeI boxes with bakelite sheet for mounting switches, sockets, fan regulators, etc and earth wire single core PVC insulated but unsheathed multistrand copper conductor cable 1100 volts grade IS-694 marked 1.5 Sqmm FRLS cable as continuous earth wire connecting to common earth dolly complete all as specified and directed by Engr- in- Charge for following

(a) One light point controlled by one switch one way

(b) One fan/exhaust fan point controlled by one switch.

(c) One socket outlet 5 Amp controlled by one switch on independent board

(d) One 3 pin 5 Amps socket outlet point on the same board controlled by one switch complete

All as per Srl item No 124 here-in-before but for one power point 6 pin 15 Amps socket outlet with 2.5 Sq mm stranded copper conductor cable PVC insulated including earth wire 2.5 Sq mm copper conductor cable connected to earth dolly complete all as specified and directed.

Supply and fixing in replacement ceiling rose, surface type, 65mm x 50mm, 3 terminal complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement stepped fan regulator 300 watt, 230 volts, 50 HZ, AC complete all as specified and as directed by Engr-in-Charge.

Supply and fixing in replacement switch piano, flush type, 5 Amps, single pole one way complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement socket out let 3 pin 5 Amps, flush type complete all as specified and directed by Engr-in-Charge.

S&F in replacement switch piano flush type ,single pole one way15 Amps complete all as specified and as directed by Engr-in-Charge.

Supply and fixing in replacement socket outlet 2 in 1, 6 pin 5/15 Amps, flush type complete all as specified and as directed by Engr-in-Charge.

S&F in replacement Indoor decorative LED battens- integrated type 20 watt 4 feet white fixture suitable for LED tube 20 watt , bi-pin holder, connector block, LED rod 20 watt etc. complete with all accessories internally pre-wired and including connecting up with twin core copper conductor cable complete all as specified and directed by Engr-in-Charge. Make Havells Cat No.- LHEXACP7UN1W020 or equivalent.

Supply and fixing in replacement LED bulb 7 watt fixed in pendent holder /bulk head complete all as specified and directed. Make Havells Cat No.- LHLDEUEEMC8R007 or equivalent.

Supply and fixing in replacement sheet metal enclosure for distribution board SPN (when MCBs to be used ) 4 way double door, 200 Amps rated bus bars and with neutral, earthing bar and din rail complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement sheet metal enclosure for distribution board SPN (when MCBs to be used ) 8 way double door, 200 Amps rated bus bars and with neutral, earthing bar and din rail complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement vertical type load line distribution board, double door ,4 way, AC, 3 phase, 415 volts, TPN bus bar 200 Amps rating and earth bar & din rail suitable for accomodation of MCCB 100/125 Amp, 16KA 4 Pole as incomer complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement MCCB, 4 pole 100A, 16KA,complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement MCB, SPN, 40A ,10KA complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement MCB, SP, 6-32A ,10KA complete all as specified and directed by Engr-in-Charge.

M&L in replacement sub main wiring with two single core 6.0 sqmm PVC insulated FRLS multistranded copper conductor cable drawing into and including rigid non metallic PVC conduit, medium grade ISI marked with all conduit fittings & fixing accessories and one single core 6.0 sqmm multistranded copper conductor cable as continuous earth wire complete all as specified and directed by Engr-in- Charge.

M&L in replacement for earthing complete for bldg with galvanized mild steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 meters below ground level) with top edge of earth plate not less than 1.5 meters below ground level connected to galvanized earth wire 4.00 mm dia by means of nuts, bolts, thimbles, check nuts, washers of GI or steel, PCC (concrete chamber of size 300 mm x 300 mm x 300 mm inside dimension) shall be PCC 1:3:6 type C-1 (using 20mm graded crushed stone aggregate) with fair finish , internal surface of concrete chamber shall be given 15mm thick plaster in CM 1:4, funnel with wire gauge of 22 gauge, 8 mesh per liner inch, 80 mm thick PCC pit cover 320 mm x 320 mm of RCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) reinforced with XPM, JALLI and charcoal dust and common salt all as shown in electrical plate No 5 of MES SSR Part-I (2020) and specified including provision of earth wire protected by 15mm dia medium grade GI pipe and watering GI pipe shall be 20mm bore medium grade etc. complete, all excavation and earth work & connecting the earthing to an earthing test point main switch board as specified and testing on completion complete all as specified & directed by Engr-in-Charge.

S&F in replacement LED bldg light highly efficient high power LED bldg light fittings 45 Watt with powder coated pressure die cast Aluminium with heat resistance toughened glass lens with internally prewired including electronic driver and connecting up with three core flexible Copper conductor 1.5 sqmm cable complete all as specified and directed by Engr-in-Charge. Male Halonix Cat No.-HLSLD-14-45-CWL or equivalent

S&F in replacement GI pipe light grade 40 mm dia bracket to make L type for bldg light fitting complete all as specified and directed by Engr-in-Charge.

S&F in replacement MS flat clamp of size 30mmx5mm thick including nuts ,bolts and washer suitable for bldg light fitting complete all as specified and directed by Engr-in-Charge.

Atish Builders LLP

SHYAM ENTERPRISES

Shiv Shankar Nirman Co.

M/S Parshant Associates