Construction of Dialysis Rehabilitation Center and Laboratory in Kolathur

Amount

Civil Work

Earth work excavation for all foundations in all type of soils and sub soils to the required level and depth for Footings, plinth / grade beams, etc,. by mechinaries including manual excavation in all type of soil . As per SS 20B as inclusive of shoring strutting and baling out water wherever necessary and including refilling 0 to 2.0m depth consolidation depositing the surplus earth in places shown clearing and leveling the site with an initial lead of 10 metre and lifts as specified hereunder etc., complete in all respects complying with relevant standard specification and as directed by the departmental officers..

0 to 2m depth

2 to 3m depth

Providing and constructing cast in situ hydraulic bored piles of specified diameter in M30 grade concrete using blended cement - slag cement with minimum cement content of 400kg/m³ in accordance with the structural engineers drawings and directions, but exculding reinforcement including cost of mobalization of all necessary plants, equipment's like piling rigs, temporary casing of appropriate length for setting out cardinal points and the removal of the same, boring in overburden, using bentonite mud circulation technique or any other method duly through all strata upto the foundation level of piles etc., complete all as approved by the departmental engineer. Further include dewatering, placing concrete by tremie pipe method, disposal of bored material outside the site. Including Chipping carefully cut off portion of piles as required without any damage to the piles and dressing the top and removing all the debris away from the site with out any extra cost as directed including the cost of all tools, plants, conveyance, all labour, lead and lift required etc .,Conducting standard penetration test to identify the refusal strata for atleast 1 pile in group and atleast 25% of piles, comparing with refusal strata as indentified in soil report and providing socketting into refusal strata by 1.00mt or into hard rock by 100% dia of the pile. (Length of pile for payment shall be measured up to bottom of pile cap).

Boring or chiselling through any obstacles, boulders, weathered rock, etc. Upto founding level of piles for seating resting or socketting of piles. The rate quoted shall include demobilising the site with all plants, equipment, piling rigs, necessary personnel brought for piling work, including removal and transportation of debrise away as directed, cleaning and reinstating site to original condition as acceptable by the Architect on completion of piling work.

450 mm dia pile (Building Pile)

300 mm dia pile (Compound wall pile)

Initial load test as per IS 2911 part IV 1995 including cost of single pile (250% of Pile capacity, labour,reinforcement charges and all other incidental charges including excavation, shoring,strutting,dewatering etc., as necessary hire charges for jacks, measuring devices, structural frames work for platform, kent ledges etc,

Carting away surplus excavated earth available with in the campus is to be carted to a lead of within 10 KM from site. The rate shall include loading into the tipper/ lorry, transporting and unloading, leveling and the earth scooped by bulldozers grading etc.,complete with all respects complying with relevant standard specification, as directed by the Departmental Officers. Rate to include materials, loading, unloading, transportation, plant and machinery, hire and fuel charges for tools and plants and other incidental charges, royalties, seignorage and taking statutory approvals as necessary to carry out the work as complete with all respects complying with relevant standard specification, as directed by the Engineer-in-charge.

Supplying and Filling with M - sand in foundation and others sub structures for 100mm thick and well watered, rammed and consolidated by power compacter. The rate includes the cost of M sand, compacting with mechanical compactors, labour charges for leveling, loading & Unloading and Transportation charges etc., complete and as per the standard specification., as directed by the Engineer-in-charge.

Providing and laying plain cement concrete 1 : 4 : 8 ratio of (1 cement , 4 sand and 8 graded stone aggregate 40mm nominal size) in foundation and basement including dewatering wherever necessary and laid in layers not more than 15 cm thick and consolidation etc. The rate includes the cost of materials, labour charges, lifting charges, loading & Unloading and Transportation etc., complete and as per the standard specification.

Providing and Laying M 30 Design Mix for all reinforced cement concrete with minimum cement content conform to IS 456-2000 using ordinary Portland cement of grade 53 from approved manufacturer, manufactured sand, 20 mm and down graded size coarse aggregates, necessary approved admixtures as per requirement. works for Footings, Grade beam, drain wall & raft , Plinth beams, Column, Grade slab, Roof slab & beam, Column drops, Pergola, Staircase waist and landing slab lintel, Sunshades, parapet Cum drops, Steps, canopy, window boxing slab, Loft, fins facia Planter box, machine foundation, elevation features and other similar structures etc..excluding necessary centering, shuttering and reinforcement which shall be measured and paid separately under relevant items. in-charge. The rate including cost of all designing the mix, batching plant, mechanical mixing, transporting and placing at all levels, leads, lifts, tools & plants, fuels, all materials, labour charges, wastages , laying, pumping the concrete to all levels, providing sleeves / openings in RCC slabs, compaction by vibrator, gunny bags for curing etc. as complete with all respects complying with relevant standard specification, as directed by the Engineer-in-charge

Basement Floor

Stilt floor

First floor

Second floor

Third floor

Fourth Floor

Terrace floor

Supplying and erecting centering for sides and soffits including supports and strutting up to 3.30 m height with all cross bracing for plane surfaces as detailed below, using mild steel sheets of 90 X 60 cm 10 gauge stiffened with MS angle of 25 X 25 X 3mm for boarding, laid over adjustable span & jacks and supported by 50mm dia pipes for general pipes scaffolding systems @ a spacing of 1.20m c/c and vertical connected at a height of 2.0m c/c including 'C' & 'U' clamps and base receiver cup at bottom for connecting pipes etc and removable systems etc., the rate including cost of all materials, labour charges, wastages, placing, transportation, lead & lifts, tools & plants, fuels, fixing in position at all levels, heights, masking tape in sheet joints, consumables, etc. as complete with all respects complying with relevant standard specification, as directed by the Engineer-in-charge.

For Plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.

For column footing plinth beam bed blocks templates staircase, steps piers, raft beam, raft slab etc.

For plane surfaces such as vertical slab, side slabs of boxing, vertical drops, facia, vertical walls etc.

Supplying, fabricating and fixing in position of steel Fe 550 grade Reinforcement for all RCC work with Thermo Mechanically Treated Bars (TMT) conforming to IS 1786 of latest version according to drawings and binding the reinforcement with 18 gauge double fold GI binding wire and providing Concrete cover blocks to maintain the cover as required. The rate including cost of all materials, bending, tying grills, placing, transportation, lead & lifts, tools & plants, fuels, all materials, labour charges, wastages , laying at all levels, fixing in position, cost of cover blocks and GI binding wires etc. as complete with all respects complying with relevant standard specification, as directed by the Engineer-in-charge.

Supply and constructing cement concrete solid block masonry work at all levels in cement mortar 1:5 (1 of Cement : 5 of manufactured sand ) using Portland Pozzolana Cement standard size of 400 x 200 mm and 200 mm thick of solid cement concrete with minimum compressive strength of 5 N/Sq.mm.conforming to IS 2185 or equivalent BS and Fly ash conforming to IS : 3812 (Part III)-1966* may be used for part replacement of fine aggregate up to a limit of 20 percent complete and as directed. Concrete blocks manufactured under strict quality control conditions using modern rugged block casting and stripping machine with the latest moulding techniques etc,. only shall be used. The rate including cost of all materials, labour charges, wastages for working at all levels with necessary lead and lifts, transportation charges, loading, unloading, scaffolding, staging, curing, fuel, consumables as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-chargee.

In Bassement floor

In Stilt floor

In First floor

In Second floor

In Third floor

In Fourth floor

In Terrace floor

Supply and constructing cement concrete solid block masonry work at all levels in cement mortar 1:5 (1 of Cement : 5 of manufactured sand ) using Portland Pozzolana Cement standard size of 400 x 100 x 200 mm of solid cement concrete blocks, with minimum compressive strength of 5 N/Sq.mm.conforming to IS 2185 or equivalent BS and Fly ash conforming to IS : 3812 (Part III)-1966* may be used for part replacement of fine aggregate up to a limit of 20 percent. Concrete blocks manufactured under strict quality control conditions using modern rugged block casting and stripping machine with the latest moulding techniques etc. only shall be used. The rate including cost of all materials, labour charges, wastages for working at all levels with necessary lead and lifts, transportation charges, loading, unloading, scaffolding, staging, curing, fuel, consumables as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

In Stilt floor

In First floor

In Second floor

In Third floor

Fourth Floor

Terrace Floor

Plastering of 12 mm thick for Internal walls with cement mortar 1:4 (1 of cement : 4 of fine P.sand) according to specifications. Rate shall include for providing GI mesh of nominal thickness at the junctions of masonry and concrete works to a width of 100 to 125mm including tying in position with suitable clamps/screws. Rate including all materials, labour charges, wastages with necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, preparation of surface, ncessary haccking in RCC surface, scaffolding, stagging, tools and plants, fuel, curing, cleaning, consumables etc as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Plastering 15 mm thick for external surfaces in cement mortar 1:5 (one cement: five P sand) with water proofing compound of “CICO No.1 or equivalent“ as per Manufacturer's Specification with sponge finish (washed sand finish) all complete as per specification and as directed. Rate including all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, preparation of surface, ncessary haccking in RCC surface, scaffolding, stagging, providing drip bands, moulds, grooves to any size and shape as shown in drawings tools and plants, fuel, curing, cleaning, consumables etc as complete with all respects complying with relevant standard specification and as directed by the Client / Engineer-in-charge.

Plastering 10 mm thick for ceiling including slabs, beams and column drops and staircase waist slab, sunshade, drops, chajjas etc..with Cement Mortar 1:3 (1 of cement : 3 of fine P.sand) according to the specification. Rate including all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, preparation of surface, ncessary haccking in RCC surface, scaffolding, stagging, providing drip bands, moulds to any size and shape as shown in drawings tools and plants, fuel, curing, cleaning, consumables etc as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Supply and painting of two coats of Acrylic emulsion paint of approved shade and colour over one coat of DCP Primer including one coat of Acrylic Wall Putty with DCP Primer. The rate including cost of all materials, brush, roller, ladder, scrapping, washing, materials, labour charges, wastages , cleaning, necessary lead and lifts, scaffolding, stagging, working at all levels, elevations, transportaion charges, loading, unloading, curing, sanding, touchup putty, surface thoroughly cleaned and wetted before painting as complete with all respects complying with relevant standard specification and as directed by the Client / Engineer-in-charge.(Internal surface)

Supplying and painting of 2 coats of weather proof exterior emulsion with high sheen, anti algal properties over one coat wall exterior primer of approved quality and shade etc., complete.Rate including all brush, ladder, scrapping, washing, materials, labour charges, wastages , cleaning, necessary lead and lifts, scaffolding, stagging, working at all levels, elevations, transportaion charges, loading, unloading, curing, sanding, touchup putty, surface thoroughly cleaned and wetted before painting as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Supply and painting in ceilings with 2 or more coats of first quality water proof cement paint of approved make and colour over one coat of priming coat white colour water proof cement paint. Rate including all brush, ladder, scrapping, washing, materials, labour charges, wastages , cleaning, necessary lead and lifts, scaffolding, stagging, working at all levels, elevations, transportation charges, loading, unloading, curing, sanding, touchup putty, surface thoroughly cleaned and wetted before painting as complete with all respects complying with relevant standard specification and as directed by the departmental officers.

Flooring with Joint free double charged vitrified tiles of approved quality, colour and design joint free of size 800 x 800 x 10 mm thick of approved make, quality and colour in all floors over a base layer of cement mortar 1:3 (one cement three sand) 20mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40 kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications and as directed by the departmental officers. Rate including all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, the same before handing over as complete with all respects complying with relevant standard specification and as directed by the Client / Engineer-in-charge.

Supplying and laying of Ceramic tiles of size 305 x 305 x 6mm for flooring approved make and quality with plain/colour with base mortor in CM 1:3, 10mm thick and pointing with white cement by adding suitable colour pigments including finishing, jointing and polishing with neat finish etc., complete. The rate including cost of all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, the same before handing over as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Supplying and fixing Dadooing the wall with ceramic tiles of approved quality, colour and design joint free of size 600x300x10mm thick of approved make, in all floors over a base layer of cement mortar 1:2 (one cement: Two sand) 10mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40 kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications. The rate including cost of all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, the same before handing over as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Supply and Laying flooring with best quality approved colour Granite slab Polished finish not less than 18 mm thick of size not less than 1200 x 600 mm machine cut and set in C.M 1:4 (1 of cement : 4 of manufactured sand) 20 mm thick topped with white cement slurry (for surface contact of the bottom of the granite slab) as per approved pattern, including finishing the joints with matching shade, cement slurry, cutting, edge chamfering and polishing rough, medium, nice and tin-oxide polish. Rate including all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, preparation of surface, ncessary haccking in RCC surface, cutting to required shape, edging, tools and plants, fuel, curing, cleaning, acid wash over finished surface, protection with Gypsum / Pop layer over plastic sheet and removing the same before handing over as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge. a) Synthetic Grey, Paradise and similar varieties

a) Synthetic Grey, Paradise and similar varieties

Supply & Laying flooring with best quality approved Jet black Granite Slab, not less than 18 mm thick of size not less than 1200 X 600mm machine cut and set in CM 1:4 20 mm thick topped white cement slurry (for surface contact of as per approved pattern including the finish joints with matching shade cement slurry cutting edge chamfering and polishing rough medium nice and tin oxide polish. The rate including cost of all materials, labour charges, wastages, necessary lead and lifts working at all levels, transportation charges, loading & unloading, preparation of surfaces necessary hacking in RCC surfaces cutting to required shape, edges, tools and plants curing, cleaning, acid wash over finished surface protection with Gypsum / pop layer over plastic sheet and removing the same before handling over as complete with all respect complying with relevant standard specification and as directed by the Engineer in charge.

Providing Polymer Coating (Water Proof Coating) for sunken portion of toilet with following specification and the surface shall be cleaned to remove all dust, foregin, matters lose materials or any other deposits of contamination by rubbing with wire brush. Slurry: Dry blend and polymer liquid blend shall be mixed into the desired ratio as per recommendation of the supplier. The mix shall be stirred thoroughly until no bubbles remain in the mix. Any lumps found in mix shall be removed. Apply first coat of polymer modified cementitious slurry by brush on wet cleaned surface. After drying, second coat shall be applied on the first coat as directed by the departmental officers etc. The rate inclusive of cost of materials and labour, etc., complete.

Supplying and filling the sunken slab area by BRICK-BATCOBA by adding CICO NO:1 or approved equivalent admixture including applying two coats not less than 2 mm thick of TAPECRETE- Acrylic Polymer Based Waterproof Coating, over the final coat of cement plaster 12 mm thick with cement sand mortar 1:3 mixed with water proofing compound like CICO No.1 at the rate specified in the manufacturer's specification after entire completion of laying pipes, sanitary fittings etc. Rate including all materials, labour charges, wastages with necessary lead and lifts, working at all levels, protecting the laid pipes and sanitary fittings, finishing the surface smooth to receive the top coat of water proofing application etc. as complete with all respects complying with relevant standard specification and as directed by the Client / Engineer-in-charge.

i) Including applying two coats not less than 2 mm thick of TAPECRETE- Acrylic Polymer Based Waterproof Coating, over the plastered surface as including final coat of cement plaster 12 mm thick with cement sand mortar 1:3 mixed with approved water proofing compound like CICO No.1 or approved equivalent conforming to IS 2645 at the rate specified by the manufacturer over coated surfacepreparation of surface, finishing, curing etc. all complete at all levels as per manufacturer's specifications and as directed.

TERRACE WATERPROOFING: Supply and laying water proofing treatment for terrace covering the following order and consisting of following operations. i) Making ' V ' grooves at the construction joints of size 20 x 20 mm and filling the "V" Groove with CICO No. 3 Quick Setting Waterproofing Compound admixed with cement.The roof slab / gutter slab shall be thoroughly cleaned to remove debris and dust, and applying 2 coats not less than 2 mm of polymer based Elastomeric Coating like TAPECRETE - RTU compound and cured for 7 days and followed by a layer of 20 mm thick cement mortar 1:3 admixed with CICO NO:1 (or) other approved equivalent make shall be spread over the prepared surface. On the spread mortar provide and lay well burnt brick bats (COBA) to a average minimum thickness of 55 mm (i.e.. minimum 40 mm thickness at lower end and 70 mm thickness at higher end). An additional layer of brick bat (COBA) shall be laid over the existing brick bat COBA surface if required to get the required gradient for adequate drainage giving a slope of approximately 1 in 120, which will be measured separately under relevant item.

The gap between brick bat shall be filled with cement mortar 1:4 admixed with waterproofing compound like CICO NO:1 or approved equivalent afterwards curing shall be carried out for two days a final layer of cement mortar of 1:3 admixed with water proofing compound like CICO NO:1 or approved equivalent make shall be laid to a thickness of 20 mm and draw a false line of 300 mm x 300 mm. The parapet side wall / gutter wall shall be thoroughly cleaned to remove all dust particles and a layer of 15 mm thick C.M 1:3 shall be laid to a height of about 300 mm above the top of the terrace/Gutter slab on the Parapet / Gutter side wall admixed with water proofing compound like the CICO NO:1 or approved equivalent make. Providing, supplying, mixing, applying two coats of ready to use two component Acrylic polymer modified cement based, flexible, water proofing slurry like or approved equivalent to a thickness of 2 mm over the plastered surface of operation as per manufacturer's specification and as directed.(Plan area of Terrace only will be measured for payment )

Providing and laying in panels not more than 20 sqm in plan granolithic flooring with cement concrete 1:1.5:3 using coarse graded aggregate of 6 to 12 mm size laid monolithic with floor concrete and finished smooth with power trowel including preparation of concrete surface and form work. The screed shall be laid for effective separation of panels not exceeding 20 sqm in plan etc and Unevenness in floor finish shall not exceed +2mm in one squaremetre area. Including sprinkling of Nitoflor Hardtop Standard evenly a shake on a ready mixed non-metallic monolithic floor hardening compound with very hard granulates of mineral origin over concrete floor when the concrete in green and touch dry condition at the rate of 5 Kgs/Sqm. Nitoflor Hardtop Standard shall possess a compressive strength of 50N/mm² as per IS: 516-1959, Moh's hardness not less than 8, as per specification and instructions of the manufacturer. Rate including all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportaion charges, pumping, loading, unloading, preparation of surface, ncessary haccking in RCC surface, power trowel, smooth finishing, fixing of screed dtrips, tools and plants, fuel, curing as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete complying with relevant standard specification and as directed by the departmental officers.

Supplying and fixing in position of Best Indian Teakwood Panelled door shutters Single leaf in position using 125 mm x 37.5 mm rails (Top, middle, bottom and lock rail) ,125 mm x 37.5 mm styles and 18.75 mm thick planks for panels including cost and labour for fixing excluding cost of varnishing the door but including cost and labour for fixing the Brass furniture fittings with required screws viz., 2 No. of 6" Door Handle, 3 Nos. of 5" Butt hinges, 2 Nos. of 6"x1/2" Tower bolt, 1 No. of 10" x 5/8" Aldrops, 1 No. of Nylon Rubber bush of size 2", 1 No. of door stopper with rubber bush, including cost and fixing of Mortice Lock and 180 angle door viewer; Brass body & lens, with cover and safety latch etc. all, complete as per relevant standard specification and as directed by the departmental officers. ( Fittings provided shall bear ISI mark. The quality, design of panel door and brand of door shutter and furniture fittings should be got approved by the Executive engineer before use)(The measurment will be taken for shutter area only)

Manufacturing supplying and fixing of steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x6mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided 1no. Aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete.

Construction of Rain water Recharge well (1200mm dia) as per consultant drawing with necessary connections, (Quotation rate)Earth work - digging the well for recharge well.supply and installation of Reinforced concrete Rings - 4 feet OD & 1 feet Height, 75 MM Thick - 10 no's.supply and installation of einforced concrete slab 4 feet in dia, 200 mm thick, and 25 mm perforated - 8 mm mild steel rods used for reinforcement -1" Perforated - 1no's. supply and installation of Reinforced concrete closing slab 75 mm thick 8 mm mild steel rods used for reinforcement with 600mm x 600mm Square HEAVY DUTY PERFORATED manhole cover.Filtration Media Installation For recharge Well Unit: 40 mm crushed stones - 0.5cum, 20 mm crushed stones - 0.5cum, Brick Bats - 0.5cum,fine sand 0.5 cub mtr Mixture of Brick Bats and Gravels for filling the gap between excavated earth and RCC rings as required Shifting of excavated earth to the approved / authorised dumping yard as directed by the authorities / Site in charge.Drilling a bore well - 200mm dia by high speed compressor- 4MTRS.supply and installation of 110mm PVC PIPE PN-6 - 4 rmtr, 110mm PVC PIPE PN-6 Perforated with 10 mm Zigzag holes to easy percolate the water - 4 rmtr, 12mm Gravel Packing between bore well hole and PVC pipe and Inserting into the Bore Well- 4 mtrs. supply and installation of - 180GSM Gio-fabric sheet to cover V-Wir screen,supply and installation of `V' WIRE SCREEN - 0.75 mm Slots. SS-304 Material - 0.5 mtrs Height - 6 " diameter ,Shifting of excavated earth upto 1000mtrs as directed by site in charge. (the well sholud be got approved by the concern department Engineer before use on works)

Size - 900mm diameter, 4.0 mtr depth and 200mm dia bore upto 4 rmtr.

Rolling Shutter Manual Operation Supplying and fixing rolling shutters of approved make, made of required size M.S. laths of size 80 x 1.20 mm interlocked together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation to the suitable size and shape as per drawing etc complete including the cost of providing and fixing necessary 27.5 cm long good quality wire springs grade No.2 and M.S. top cover of 1.20 mm thick for rolling shutters. The rate shall be inclusive of one coat of red oxide primer and two coats of synthetic enamel paint of approved quality and colour. Rate including all materials, labour charges, wastages, necessary lead and lifts, transportation charges, loading, unloading, scaffolding, staging, installation charges, fuel, consumables as complete with all respects complying with relevant standard specification and as directed by the Client / Engineer-in-charge.

RS1 - Rolling Shutter - / 3000 mm x 2100 mm

Providing and fixing of 1.2mm thick Lead Lining Door for X-Ray Rooms, Scanning Rooms with Mild Steel Door Frames 105mm x 57mm X 18 G and 12 G x 50mm Shutter made of GI with PWG finish and honey wool insulations with SS 101mm x 75mm x 3mm SS 304 Ball Bearings Butt Hinges, Mortice Sash Lock ML 100A, 50mm BS, 85mm centre, CL 207 : Key & Knob 70mm, 5 Pin Cylinder with Handle SS Finish (Dorma Make), Heavy Duty Door Closer, Frames fixed wih walls using Mortice Sash Lock ML 100A, 50mm BS, 85mm centre CL207: Key & Knob 70mm, 5 Pin Cylinder with Handle SS Finish (Dorma Make) all neccesaryaccessories and fittings as per the required and as per theapproval for the Department Officer

Providing and fixing sliding door, shutter frame made of aluminum 62mmx38mm and vertical aluminum frame of size 45mmx45mm door bottom frame size 100mmx25mm,Door middle frame size 45mmx45mm door top frame size 45mmx45mm with necessary aluminum clip and rubber filling. Shutter made of 9mm Novapan Board up to 900mm above 900mm to 2100mm fixed with 5mm thick plain glass with C sliding track with necessary hardwares etc. the rate includes all labour, transport and fixing charges complete

UPVC Window Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point lo cks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work.

UPVC Window

Supplying and erecting in position of 1000 liters capacity Industrial Model Reverse Osmosis Water-cum-Purifier to deliver Potable Water with World Health Organisation (WHO) Standards with following accessories.(a) MS Skid - 1 No. (b) Media 11054 No. Vessel with 20 nb Multiport Valve (with Media Pubble and Fine Sand and Activated Carbon Filling) set (c) Feed Pump 0.50 HP – 1 No. (d) Vertical Pump 2-9, 2.00 HP / Single Phase – 1 No. (e) Membrane 40 x 40 filmtech (or) equilaents / Osmonic (USA) - 1 No. and Membrane Pressure Vessel 40 x 40 -1 No. & Pressure Gauge - 2 Nos. (f) Flow Meter - 1 No. 20” Filter with Housing - 1 No., Low Pressure Switch - 1 No., Level Switch - 1 No. & Necessary CPVC Pipes and Fittings. The system shall be provide with Two Panel Control System with necessary Stainless Valves and Fittings and Float Control etc. The rate should be inclusive of all civil works, wherever necessary to install the System in position and intact.

1000 Litres

UPVC Ventilator Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on wor

Providing and fixing welded M.S. grills to the window openings,along the details as per drawing with necessary screws, bolts and fixed with necessary M.S. lugs embedded in masonry with C.C. 1:2:4 and finishing the surface neatly. Rate shall welding and consumables, etc. complete, as directed. Design of grills and the size of members to be used shall be got approval before put into use & as directed by the Client / Engineer-in-charge.

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors including cost of priming coat etc., complete complying with standard specification. ( The make quality and colour of paint should be got approved by the executive Engineer before use on works.)

Supply and installation of Anutone (or) Euivalent Brand of Acoustical False Ceiling of subtex nubby, square edge, glass fibre core fully encapsulated ceiling tile of size 595 x 595 x 15mm having volume density 120 Kgs / m3, weight 1.8 / 2.4 / 3 kg / m2 which is suspended by using 0.3mm thick skelet trelis T15 metal grid system.Skelet trelis T15 metal grid system of 600 x 600mm module includes skelet WA15 W30 wall angle with unequal flanges of 15 / 19mm,length 3000mm, fixed along the perimeter of walls with the help of nylon sleeves and suitable fasteners at 300mm centers. Then suspend the skelet MT15 W36 MainT with flange width 15mm, height 32mm and length 3600mm, from the soffit slab with help of soffit cleat and wire rod with leveling spring clip at 1200mm centres.Skelet CT15 W12 CrossT with flange width 15mm, height 26mm and length 1200mm is interlocked into the pre-cut slots in the Main T15 at 600mm centers in the perpendicular direction to the Main T15. Finally, the skelet CT15W06 CrossT with flange width 15mm, height 26mm and length 600mm are interlocked into the precut slots in theCT15W12 CrossT in direction parallel to the Main T15 to result in 600 x 600mm module. The subtex nubby square edge of size 595 x 595x 15mm shall be placed into the grid size of 600 x 600mm. Ensure arrow marks behind the tiles are oriented in one direction to achieve uniform shade. The systems to achieve noise reduction coefficient not less than 0.9 NRC, so as to have an neat appearance as directed by the department offices. The cost includes, cost of material, cost of labour, scaffolding, transportation, conveyance, etc. complying to standard specication.

Supplying and laying precast Rubber Moulded hydraulically pressed cement concrete paver block with pattern design of 50% colour and 50% Plain made of M40 grade concrete - 83 mm thick of approved quality and colour, over the filling manufactured sand to 50 mm thick, levelling and compacting with plate vibrator and laying of the inter locking paving blocks with sand binding and final compaction with plate vibrator of 3 tonne capacity finishing the surface including cutting of blocks at the edges including all labour, materials, transportation, shifting etc., complete, as directed by the Client / Engineer-in-charge

Painting the wall, with two coats of best approved first quality Texture finish paint over the wall in all floors including cost of priming coat and with texture putty etc., complete complying with standard specification. ( The make quality and colour of paint should be got approved by the executive Engineer before use on works.)

Providing and fixing of Aluminium Composite Panel (ACP) 4 sided having 50 x 25 x 1.50mm frame work vertical and horizontals out of specially designed extruded sections withstand wind pressure of 180 Kg/sq.m and fabricated fixed at all level elevation and heights. The extruded section cutting and fixing required space extruded section shall be of 6063 and alloy of BSH 9 onfirming T is – 63400 rate shall included to fix the main frame with necessary clamps, fasteners, bolt nuts etc. The main frame of extruded section shall be of 22843 & 22739 (H9) grade conforming to BS 4174 (or) IS 8147. Rate shall included 4mm thick ACP sheet (0.25 + 3.5 + 0.25) alstrong or equivalent fixing with spacer tape and the ACP sheet bounded with special type structural sealant of dow corning 789 or equivalent in dust free conditions the gaps between ACP sheet to be filed with whether sealant and backer rod or 12mm foam sheet to ensure water and air tightness in all complete complying with standard specification as directed by the departmental officer

Structural Glazing: Providing and fixing structural glazing fabricated from roll formed sections made of galvanized steel colour coated (Base steel as per IS 513 of ‘D’ quality, galvanized as per IS 277 with Zinc of 120 grams / sqm.) with total coated thickness of 0.72mm. The glass holding section made of 304 grade SS of 0.6mm thick. Galvanized steel sections are to be used as stiffeners inside the colour coated steel / powder coated sections as per the design requirement. Design calculations are made to suit wind pressures as given in IS Paint specifications: Primer coat with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer of 5-7 microns or powder coated with pure polyester powder upto 50-60 microns thick. Dimensions: The section should be of 37 x 53mm for frame vertical, 37 x 53mm for frame horizontal section and section for reinforcement should be of 31 x 55mm. glass holding section should be of 37 x 37mm for top and bottom grids in between should be of 37 x 18mm.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade),calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)

Galvanized steel ladder consisting of 50mm diameter pipe ladder rails, 25mm diameter pipe ladder rungs welded at max, of 300mm centres, 40mm diameter pipe braces fixed in position complete including painted finish, fixing plates, bolts and all fixing material and accessories.

Ladder - 600 x 3850 mm high

Providing and fixing 304 grade stainless steel mosquito net in windows Rate including all materials, labour charges, wastages, necessary lead and lifts, transportation charges, loading, unloading, scaffolding, staging, installation charges, fuel, consumables as complete with all respects complying with relevant standard specification and as directed by the executive Engineer before use on works.)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :For fixed portion - Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing PVC/GI sleeves in form work in slabs and beams . PVC sleeves cut to size are to be tied with GI wires to reinforcement.

a) Upto 50 mm dia to 100 mm dia

b) Above 150 to 200 mm dia.

Providing band with cement mortar 1:5 (One of Cement and Five of Sand) 12mm thick finished with neat cement including,scaffolding curingetc..,complete complying with relevant standard specification and as directed by the departmental officers.

75mm thick band

Supplying and fixing of 24watts LED decorative gate light fitting philps or havells complete with suitable length 32mm dia GI pipe Class B on the existing gate piller with supply and fixing of M.S box of 30cm x 20cm x 10cm with angle iron frame work with door and lock key arrangeent with supply and fixing 16amps fare unit 250V 5amps SP switch in side the M.S box with PVC unsheathed copper lead with 20wats retrofit CFL lamp..

Providing, cutting and fixing desired 20mm thickness of expansion joint filler Dura Board HD-100 (closed cell, compressible ,pre-molded Polymer joint filler board ) in black color Manufactured by Supreme Industries Limited Conforming IS Standard IS 1838 (Part-3) Having density of 95kg /Cu. Mt. Non-Staining with less than 1% water absorption & Compression recovery of 93 % minimum as per specifications.

Supplying & fixing PVC mould CI Steps for Sump etc all complete in all respects complying with relevant standard specification and as directed by the departmental officers.

Supplying and fixing SFRC manhole cover with frame as per approved make ,cover weight and being size mentioned below and specified size in the drawing etc., including painting with two coats of anticorrosive paint over a coat of primer etc., fixing locking arrangements, fixing Man-hole over, grouting the anchors with CC 1:2:4 (one cement, two fine aggregate and four coarse aggregate), as complete in all respects complying with relevant standard

Plumbing Works

Water Supply, Saintary and Rain Water Arrangement

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). Internal &External

110 mm dia

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below Stilt level

160mm dia PVC soil / waste pipe

110mm dia PVC soil / waste pipe

75mm dia PVC soil / waste pipe

50mm dia ASTM-D schedule 40threaded UPVC pipe with necessary UPVC/GI specials

40mm dia ASTM-D schedule 40threaded UPVC pipe with necessary UPVC/GI specials

32mm dia ASTM-D schedule 40threaded UPVC pipe with necessary UPVC/GI specials

25mm dia ASTM-D schedule 40threaded UPVC pipe with necessary UPVC/GI specials

20mm dia ASTM-D schedule 40threaded UPVC pipe with necessary UPVC/GI specials

Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on work.

50 mm GM Gate

Supplying & fixing in position 15 mm dia brass/ C.P screw down tape (Heavy duty) of approved make conforming to I.S. Specifications & quality including cost of shellac, thread etc., complying with standard specifications & including cutting & threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the work).

15mm dia CP Screw Down Tap

15mm dia CP Pillar Tap

Supplying and fixing in position Mirror of size 1000x780mm of approved quality and brand with necessary plastic back PVC frame with bottom stand using brass screws rawl plugs for fixing etc complete complying with standard specification and as directed by the Departmental officers. The colour of frame and quality of mirror should be got approved by the Executive Engineer before use on work

Supplying and fixing Brass Chromium Plated Towel Rail 60cm long and 20mm dia with brackets of same materials including cost of teak wood plug & CP screws etc., complying with standard specification and as directed by the Department officers.

Supplying and fixing the best quality approved /equivalent make of C.P.Soap Dish Holder with wall flange including cutting and making good the walls wherever required etc. complete, complying with standard specification and as directed by the Department officers The quality and make of soap dish should be got approved by Executive Engineer before use on work.

Supplying and fixing the best quality approved make of C.P. health faucet with wall hook onemeter long flexible tube, including cutting an d making good the walls whereve r required etc.complete, complying with standard specification and as directed by the Department officers. The quality and make of health faucet should be got approved by Concern Engineer before use on work.

Health faucet

Supplying and fixing Wash Hand Basin of size 550 x 400mm with all accessories such as cast Iron Brackets, 32 mm Dia C.P. Waste coupling, Rubber plug and Chain, 32 mm dia ' B ' Class G.I. Waste pipe, 15 mm Dia G.M Wheel valve; 15 mm Dia Nylon connection, 15 mm Dia Brass Nipples, 15 mm C.P. Pillar tap etc.,including fixing the wash hand basin in the wall in position with a pair of C.I. brackets with teak wood plugs and screws and giving necessary water supply connection and as directed by the Department officers. (The Wash basin should be got approved by the Executive Engineer before use on works.

Supplying and fixing in position best quality approved make white glazed earthernwere sink of size of 600 x 450 x 200mm including cost of 32mm dia CP waste coupling, 32mm dia PVC waste pipe with rubber plug and chain, 15mm dia brass nipple including fixing the sink in position and testing for leakages etc., complete complying with standard specifications excluding CI brackets. [The sink and specials should be got approved by the Executive Engineer before use on works]

Supply and fixing in position white European Water Closet of approved make with low level flushing tank 10 litre capacity of best quality and approved make double flapped seat cover, pan connector with comprising the P- trap/"S" trap, C.P brass hinges and including labour, all fittings, making the required size including cutting the wall, and fixing the flushing cistern properly, redoing the plastering and packing the wall with smooth finish, the side gap between EWC mouth and pan connector to be filled with silicon sealant etc.complete, complying with standard specification and as directed by the Department officers. The quality and make of EWC should be got approved by Concern department Engineer before use on work. complete complying with standard specification and as directed by the Departmental officers

White glazed European Water Closet with 12.5 litre capacity.(P-54, Unique code : M-0534)

Supply and fixing in position of best Indian make white / colour glazed earthernware lipped mouth flat back urinal of best quality and approved make of size 430mm x 260mm x 350mm with GI pipe, 32mm dia bell mouth PVC connection and waste pipe, 15mm dia GI pipe of required length, 15mm dia GM wheel valve, 15mm dia brass nipple 2 Nos., and fixing the urinals in position with necessary TW plugs, clamps, screws, etc., including dismantling masnory and re-doing the same to the original condition, etc., including painting the pipe with two coats of best quality approved synthetic enamel paint over one coat of red oxide primer and checked without any leakage etc. complete complying with standard specifications and as directed by the departmental officers. (The urinal should be got approved by the Executive Engineer before use on works.)

White glazed earthernwere lipped mouth flat back urinal

Supplying & fixing in position PVC Nahini / Floor trap of size 100x75mm including stainless steel gratings of approved brand & quality, fixed over a bed of brick jelly lime concrete 1:2:5 ( One part of lime, two parts of sand & five parts of 40 mm size brick jelly ) & finished with cement mortar 1:3 ( One cement & three M sand ) including dismantling masonry works wherever found necessary & making good the damaged portions to the original condition & giving connections to the cast iron pipes etc., complete, complying with standard specification. (The PVC Nahini / Floor trap should be got approved by the Executive Engineer before use on works ).

Nahani Trap of size 100 x 75mm with stainless steel gratings

Supplying & fixing in position 150 X 100 mm square mouth 'P' or 'S' trap stone ware Gully trap 'A' grade with cast iron double gratings of size 150 X 150 mm with C.I. air tight cover with frames of size 300 X 300 mm at bottom & top respectively with necessary earth work excavation, laid over a bed of brick jelly cement concrete 1:3:6, 150 mm thick using 20 mm size broken brick jelly including necessary brick work & plastering, &including dismantling masonry wherever necessary & redoing the damaged portions to the original condition & by using cement concrete 1:3:6 using 20 mm stone jelly for fixing the Gully trap & giving connections to the stone ware sewer line etc., complete, complying with standard specification. (The stone ware gully trap should be got approved by the Executive Engineer before use on works ).

Supplying and fixing approved make Handicapped -Swp Grab Bar with necessary fixing screws etc complete. The rate including all labour charges for fixing, transportation complete. The material should got be approved by the Executive Engineer before use on works.

Supply ,erection and testing & commisioning of 3HP submersible pumpset in the to suit 200mm borewell of capacity of 4800 LPH @ 265Ft, max. total head of 280 Ft pumps fitted with bronze impellers and having delivery size of 40mm - 430V along with 3mts cable and manufactures standard control panel which is mandatory and as directed by the officer incharge.

(From UG sump to O.H.T)

Labour charges for the erection of submersible pumpset in borewell/openwell including fixingand jointing submersible cable with proper clamps upto the starter to required depth and also fixing of riser pipes to the required depth valves erection clamps, pressure gauges upto the exterior wall of pump room and erection of panel board consisting of TPICN switches starter, Voltmeter, Ammeter, three pilot (indicating) lamps capacitor single phasing preventor, water level guard and laying and jointing the cables and twin earthing as per IE rules etc., complete and testing the pumpset and trail run for 10 days.

Supply ,erection and testing & commisioning of 5HP submersible BORE WELL pumpset in the to suit 200mm borewell of capacity of 4800 LPH @ 265Ft, max. total head of 280 Ft pumps fitted with bronze impellers and having delivery size of 40mm - 430V along with 3mts cable and manufactures standard control panel which is mandatory and as directed by the officer incharge.

BORE WELL PUMP)

Labour charges for fixing the 3 phase panel board with required fittings complete, including all labour charges as direced by the engineer in charge

Jaquar Integra Split Heat Pump 500 Ltr HPS-WHT-500 The rate including all labour charges for fixing, transportation complete. The material should got be approved by the Executive Engineer before use on works.Heat Pump

Heat Pump

Drilling of 12" dia vertical borewell so as to have a finished size of 6" dia borewell in boulder area to any required depth as decided by the TWAD Board Officers including Transportation from one place to anothr place with in Tamilnadu State by direct or reverse rotary mud circulation method using Contractor's rig tools, fuel, labourers, bentonite mud and water required for drilling at the site shown by the TWAD Officers including construction of mud pit etc. using only calyx rigs.

Reaming from 200mm dia pilot bore to 350mm dia bore as direct by the Engineer incharge up to 80mtr depth ending below ground level. (As per Schedule Item No: 7f, P.No: 301)

Supply and laying following dia PVC casing pipe with excise duty as per IS 12818 / 1992 ( 1.1 (4,6,3), P.No: 22

200mm dia CS

200mm dia RS

150mm dia RS

Labour charges for inserting PVC casing pipes assembly (with slots or without slots) in the drilled hole including jointing the pipes with PVC couplers with cement paste etc., complete, supply and packing the annular space with pebbles of size and quality as approved by the Executive Engineer of Departmental officers.

200mm dia CS

200mm dia RS

150mm dia RS

Supplying and filling with river pebbles in annular space between bore and PVC pipe up to hard rock.

Charges for developing the borewell with air compressor of 300 CFM capacity (Minimum 8 Hours) including transportation labour and fuel charges for compressor as directed by TWAD Board Officers and conducting yieldtest by 'V' notch method.

Supply ,erection and testing & commisioning of 3HP submersible pumpset in the to suit 200mm borewell of capacity of 4800 LPH @ 265Ft, max. total head of 280 Ft pumps fitted with bronze impellers and having delivery size of 40mm - 430V along with 3mts cable and manufactures standard control panel which is mandatory and as directed by the officer incharge and other required supporting items like SS hose nipple, nylon rope, clamps, bolt and nuts,GI nipple, 50mm dia HDPE hose of required length etc completed and as directed by the officer incharge.

FIRE FIGHTING WORKS

FIRE FIGHTING PUMP ROOM EQUIPMENT

Supply, erection, testing and commissioning of Fire Fighting Application Horizontal Centrifugal Type Pump Rated for 2280 LPM at 70 metres head with Electrical Motor of 60 HP of 415 volt 3 phase connection complete with base plate and accessories. (Make: Kirloskar or Equivalent). The rate inclusive of necessary vibration, bad mounting etc., as per standard method as directed by the Deparmental Officers.

Supply, installation, testing and commissioning of Diesel Engine Driven Main Fire Pump suitable for automatic operation and consisting of following and complete in all respects as required. a. End suction, top discharge centrifugal pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal to ensure a minimum pressure of 3.5 kg. / sq. cm at highest and farthest outlet at specified flow of 2280 LPM at 70m head conforming to IS 1520. b. 68 BHP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant BS & IS standard complete. Auto starting mechanism, 12 volts / 24 volts electric starting equipment like self motor, dyanamo, solenoid switches etc. c. 110 litres capacity diesel tank mounted over stand fabricated using 25mm x 25mm x 6mm size MS angle, providing with level indicator, inlet port, outlet port, drain port and diesel return line port and fuel pre-filter, after filter etc. (Make: Kirloskar / Equivalent). d. Exhaust system having flexible metallic mufler, 100mm dia MS heavy pipe extended upto 1m, outside pump house duly insulated with 50mm thick glass wool with 1mm thick aluminium sheet cladding, residential silencer with necessory MS support arrangements from wall or ceiling as per site condition.

Supply, erection, testing and commissioning Mono Block type Fire Fighting Pressurisation Pump of 180 LPM 110 metres head at 10 HP with suitable base frame including necessary vibration bad mounting etc., including conveying, fixing and incidental charges., etc., complete as per standard specification and as directed by the Departmental Officers. (Make: Kirloskar/ Equivalent)

Supply, erection, testing and commissioning of Air cushion tank of 300 mm dia. & 1000 mm height with drain connection. The rate shall be inclusive of accessories such as:25mm dia Air release valve 25mm dia ball valve etc, completed. Located in pump room.

Supplying, erection, testing and commissioning of Diesel Engine Pump Main Control Panel & Jockey Pump including necessary auto cut-in, cut-off and manual operations, battery charger switch arrangements, voltmeter, ammeter and running indication siren provision, wall mounting type, etc., as per the standard method and as directed by the Departmental Officers.

Autostart panel for the Diesel engine complete auto / manual switch, indication lamps protective fuses with battery charges, suitable of working on 230 V, with one hour back up,AC, single phase, enclosure being vermin,dust proof and panel compatable to BMS. Location at Ground floor lvl.

Supplying, laying, testing & commissioning of FRLS,PVC outer sheath, steel armoured, aluminium conductor, 1100v grade power cables with glands etc.The cables shall be laid in tray / Hume pipe / in trenches/on walls/ floor etc. as required. For cables laid out door the rate shall include earth excavation providing brick and sand protection, refilling and compacting the earth.The rate shall exclude tray & Hume pipes but includes for the required no of end terminations as mentioned below.The minimum size of the cables shall as mentioned below, with all the end terminations

2R X 3.5 C X 50 sq.mm Copper armoured cable for main pumps

1R X 4 C X 6 sq.mm. Copper armoured cable for Jockey pumps

12 C x 2.5 sq.mm.Aluminum cable Diesel engines

4 C x 1.5 sq.mm Copper armored for Instrumentation

Supplying and installing of perforated G.I.sheet cable tray with necessary angle iron suspension supports, anchor fasteners etc. complete. Maximum height of suspension shall Not exceed 500 mm.Size of the tray shall be suitable for laying the above mentioned cables.

G.I. Earthing strips of sizes mentioned below, strip shall be run on floor / ceiling / walls, from the equipment to the nearest Earth pit with neccessory accessories as required. (Earth pit shall be executed by other agencies).

25 x 3 mm GI strip

50 x 6 mm GI strip(PUMP EARTHING)

Supply, erection, testing and commissioning of following MS ‘C’ Class Heavy Duty Pipe as per IS 1239 to withstand a developing pressure of 10 kg. / sq.cm including necessary fittings like MS flange of table ‘E’,elbows, reducers, gaskets, bolt, nuts with washers & joints as per standard method of arc welding, including one coat metal primer and two coat Post Office Red painting including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the

250mm dia

200mm dia

150mm dia

100mm dia

80mm dia

50mm dia

25mm dia

Supply, Installing, testing and commissioning of slim seal type butterfly valves with shperoidal graphite iron disc (SG iron), with nitrile rubber seal and tested to 10kg / sq.cm including a set of suitable GI flanges, as per BS 10 Table - 1, bolts, nuts GI washers, neoprene rubber gaskets etc., complete.

100 mm dia

80 mm dia

Supply, erection, testing and commissioning of cast iron body and bronze internal non-rising spindle sluice valve of sizes at required places to control the flow of water including necessary MS flange of table ‘E’,gaskets, bolts & nuts including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: NORMEX / KARTAR / EQUIVALENT

150 mm dia

Supply, erection, testing and commissioning of Cast iron body and Gun metal or stainless steel internal Non-return valve of following sizes to control one way flow of water to be installed pump room at delivery line and near overhead tank at terrace level near to jockey pump and motor including necessary MS flange of table ‘E’, gaskets, bolts & nuts, etc. as per IS 5312 including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary,etc., complete as per standard specification and as directed by the Departmental Officers.

150mm dia

100mm dia

Supplying, installing and commissioning C.I.flanged "Y" type Strainer with SS mesh, suitable flanges, nuts, bolts, gaskets etc. complete.

150mm dia

80mm dia

Supplying, installing ,testing and commissioning of Flow meter( Electronic type) on Test line to measure 175 % of pump flow and suitable to 150 mm dia.

Supply, erection, testing and commissioning of Pressure Gauge with 0 to 14 kg. range of reputed make with necessary valve, milling thread MS coupling fixed at delivery pipe line in pump house to read the developing pressure including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: HGURU / ISI MAKE / EQUIVALENT.

Supply, erection, testing and commissioning of suitable Pressure Switch of reputed make line Indfoss or Donfoss including necessary valves,couplings, etc., connected with electrical main control panel and setup at proper differential so as to auto start and auto stop the electrical motor,jockey motor including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., completed as per standard specification and as directed by the Departmental Officers. Make: DONFOSS / INDFOSS / ISI MAKE / EQUIVALENT.

Supply, erection, testing and commissioning of ball valves of brass body nickel plated with stainless steel ball, lever operated and tested to 20 kg / sq.cm.

25 mm dia

Supplying, installing ,testing and commissioning of additional length of exhaust pipes M.S. Medium grade Class B with mineral wool insulation with aluminum sheet with long radius bend from residential silencer with necessary clamps, fixtures, civil works and 2 coat painted with heat resistant, rust proof, bituminous paint of approved colors to full height, in stages of following sizes including suitable rain guard for top. Fixing shall be done with proper GI clamps, expansion bolts, support angle of size 40X25X3 mm, also painted, fixed on the wall / inside the duct etc .complete, as instructed by the Engineer.

150 mm dia M.S. Medium grade with mineral wool insulation with aluminum sheeting & Structural Steel Supports

Supply & installation of 20 NB Automatic Air Release Valve along with ball valve all complete as per specifications.

FIRE HYDRANT SYSTEMS

Supply, erection, testing and commissioning of following MS ‘C’ Class Heavy Duty Pipe as per IS 1239 to withstand a developing pressure of 10 kg. / sq.cm including necessary fittings like MS flange of table ‘E’,elbows, reducers, gaskets, bolt, nuts with washers & joints as per standard method of arc welding, including one coat metal primer and two coat Post Office Red painting including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the

150mm dia

100mm dia

Supply, Installing, testing and commissioning of slim seal type butterfly valves with shperoidal graphite iron disc (SG iron), with nitrile rubber seal and tested to 10kg / sq.cm including a set of suitable GI flanges, as per BS 10 Table - 1, bolts, nuts GI washers, neoprene rubber gaskets etc., complete.

150 mm dia

100 mm dia

Supply, erection, testing and commissioning of Cast iron body and Gun metal or stainless steel internal Non-return valve of following sizes to control one way flow of water to be installed pump room at delivery line and near overhead tank at terrace level near to jockey pump and motor including necessary MS flange of table ‘E’, gaskets, bolts & nuts, etc. as per IS 5312 including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary,etc., complete as per standard specification and as directed by the Departmental Officers.

150mm dia

Supplying, erecting and commissioning of Landing Hydrants comprising of the following in the Fire duct;

Oblique single headed hydrant valve as per IS 5290, made of gunmetal with 63 mm dia instantaneous outlet of 80 mm dia fanged inelt ,Blank caps , gun metal cap GI chain twist release type lug and hand wheels etc complete.

2Nos lengths of 15 M long, 63mm dia RRL hose with instataneuos couplings and Hoses shall be stored in side the hose cabinet.

1 no. Gun metal short branch pipe with nozzle.

Hose reel drum (powder coated finish) of swinging type with 19mm dia Rubber braided hose of 30m length fitted with 6.35mm dia nozzle with Ball valve ( upstream) and Shut off nozzle, complete.

Providing & fixing indoor type hose lockable cabinet frames fabricated from 40 x 40 x 5 angle iron sections and 16 gauge MS sheet with full front glass door and locking arrangement, suitable to accommodate landing valves, 15 m long hoses, first-aid hose reel and branch pipe nozzle & fire mans’ axe. The cabinet frame shall be painted with one coat of primer and two or more coats of synthetic enamel paint of approved make and shade of as required (Approx 2.1 m (high) x 0.9 m (wide) x 0.6 m (deep) ). The item shall be complete of MS housing with front door. (Cost shall be inclusive of providing break glass box containing key for the cabinet along with hammer).

Providing and fixing standard fireman's axe with heavy rubber handle.

Supply, erection, testing and commissioning of Fire Fighting 4 Way Fire Brigade Inlet with necessary gun metal 63mm dia non return spring shutter arrangements, so that to control one way flow at the time of emergency water supply by fire and rescue service fire engine entry including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: KIARTAR / OMEX /EQUIVALENT.

Oblique Hydrant valve as per IS 5290, made of gunmetal with 63 mm dia instantaneous out & 80 mm dia fanged inelt inlet,Blank cap , chain and hand wheel etc complete.

2 Nos lengths of 15 M long, 63mm dia RRL hose confirming to IS 636 Type A with instataneuos couplings and Hoses shall be stored in side the hose cabinet.

1 no. Gun metal short branch pipe with nozzle confirming to IS 903.

Supply and installation of Hose cabinet consists of 2 Nos RRL Type-A hoses of 63mm Dia x 15 meters long with heavy quality Stainless steel male coupling as per IS: 903 combined with 1 Nos of nozzle and 1 No of branch pipe. The hose cabinet shall be of reputed manufacturer with MS sheet (16 SWG thick) of size 750x600x250 with glass fronted door, painted in red out side and white in inside, hose boxes along with GI support arrangements as per specifications

Supply & installation of 20 NB Automatic Air Release Valve along with ball valve all complete as per specifications.

AUTOMATIC SPRINKLER SYSTEM

100 mm dia

65 mm dia

50 mm dia

40 mm dia

32 mm dia

25 mm dia

Supply, Installing, testing and commissioning of slim seal type butterfly valves with shperoidal graphite iron disc (SG iron), with nitrile rubber seal and tested to 10kg / sq.cm including a set of suitable GI flanges, as per BS 10 Table - 1, bolts, nuts GI washers, neoprene rubber gaskets etc., complete.

100 mm dia

80 mm dia

50 mm dia for Drain

Supply, erection, testing and commissioning of Cast iron body and Gun metal or stainless steel internal Non-return valve of following sizes to control one way flow of water to be installed pump room at delivery line and near overhead tank at terrace level near to jockey pump and motor including necessary MS flange of table ‘E’, gaskets, bolts & nuts, etc. as per IS 5312 including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary,etc., complete as per standard specification and as directed by the Departmental Officers.

150mm dia

Supply,erection, testing and commissioning of 15mm dia nomial bore quartzoid bulb Pendent type sprinklers with temprature rating of 68 deg C,K=80 , conventional type including with CI taper special confirming to BS 164. The rate shall also include suspending arrangement with ceiling, wall arrangement with ceiling, wall beam clamps,fasteners,etc complete. The rate shall be inclusive of Stainless steel Rosette plate for false ceiling areas.

Pendent Sprinkler

Supply, erection, testing and commissioning of UL approved Metallic stainless steel (SS 304) corrugated or braided Flexible drop pipes of 25mm dia with cross bar assembly support suitable for grid ceiling, reducing fitting, special shoulder Nipple, redcing nipple, T bar braket, braket clip assembly. Flexible length shall be upto 1000mm long .

Supplying, installing, testing and commissioning flow switch installed on the sprinkler main distribution line capable of sending impulses to the Monitor Module.

100 mm dia

Supply & installation of Instrument cables for flow switches. The cable should be 2 Core x 1.5 Sq.mm copper Arm cable. (FRLS)

Supply, installation, testing and commissioning of Sprinkler Alarm Valve, water flow will activate a hydraulic powered water motor alarm by way of integral valve alarm line trim piping. Water motor gong shall be connected to a water pressure retarding chamber to limit the propensity of unnecessary alarms. Water motor alarm shall be equipped with a rear closure plate to limit the access of foreign materials of accumulation of debris. Size: 150 NB

Supply & installation of 20 NB Automatic Air Release Valve along with ball valve all complete as per specifications.

FIRE EXTINGUISHERS

Supplying, installing and commissioning Portable Fire extinguishers of following type & capacity.

Supply and fixing of Carbon-di-Oxide Gas Type 2 kg. capacity Fire Extinguisher as per New IS15683, complete with control valve, discharge hose with horn,wall mounting bracket, safety clip etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc.,complete as per standard specification and as directed by the Departmental Officers

Supply and fixing of stored pressure ABC (Mono Ammonium Phospate) Powder Type Fire Extinguisher of 6 kg. capacity as per IS:15683 with pressure gauge, discharge hose & control nozzle, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc, complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT / SAFETY FIRST / EQUIVALENT For 6 KG

Fire bucket of 24kg galvanized steel sheet standard 9 litre capacity & round of bottom shape painted white inside and red outside & black on the bottom done with letters "FIRE"in black & gold with wall mounting bracket,fire bucket stand & screws (each 4 nos)

SIGNAGES

Door Mounted Facility Announcer: Providing and fixing Non-illuminated signs including all operations from fabrication to installation all complete as per drawings, technical specifications. Sign face: Sign face shall be made in 5 mm thick 040 white acrylic (as specified) having Energy efficient or equivalent self-adhesive cast translucent vinyl of approved colour to be processed in a dust free application room. The translucent film should have clear adhesive and to be designed for backlit LED and provide energy efficient solution. The colored vinyl should of cast manufacturing and meeting to pantone / RAL shade confirmed by customer in reflected light conditions. The vinyl thickness should not more than 60 microns without adhesive when measured using IS standard 2508:1984 or ASTM equivalent. The Adhesive of the film should clear and pressure sensitive. The liner of the Film should Synthetic, lay-flat liner that is not affected by water or humidity.The colored vinyl should confirm to class A rating for fire retardant as per ASTM E84 standard - (Standard Test Method for Surface Burning Characteristics of Building Materials) and pass DIN EN 13501-1 (DIN 4102) - (Fire Test to Building Material). The film should also comply to UL746 standard for Polymeric Materials Short Term Property Evaluation

Sign Frame:Providing and fixing sign frame 25 mm wide powder coated, colour RAL 9006 special aluminium extrusion with inbuilt frame to recieve the sign face. The sign face shall be fixed to sign frame with the 3M brand dual lock system in one side and 3M bothway tape from the other side.Accessories: Providing and fixing all accessories such nut-inserts, screws , rivets, bolts, washers, nuts, etc. complete as per drawing. Cost to include all internal connections and Wiring, terminating and connecting with the incoming cable at the site.The actual structural design of the sign for its stability shall be responsibility of the EPC contractor. Secret fixing methods should be used to fix parts together. Accessories: Providing and fixing all accessories such as thimbles, end connectors, nut-inserts, screws , rivets, bolts, washers, nuts, etc. complete as per drawing and as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

EMERGENCY EXIT (400mmx150mm double side)

FIRE EXTINGUISHER (100mmx150mm single side)

FIRE EXIT (400mmx150mm double side) .

ENTRY & EXIT (400mmx150mm double side)

MANUAL CALL POINT (100mmx150mm single side)

HOOTER (100mmx150mm single side)

Providing and fixing illuminated signs including all operations from fabrication to installation EVACUATION PLAN with AUTO GLOW in A2 . The rate includes the cost of materials, labour charges, lifting charges, loading & Unloading and Transportation etc., complete and as per the standard specification

Providing and fixing illuminated signs including all operations from fabrication to installation INFORMATIVE WALL (IN RAMP AREA - 1.50 X 1.18M) . The rate includes the cost of materials, labour charges, lifting charges, loading & Unloading and Transportation etc., complete and as per the standard specification.

Electrical Works

CT Metering Panel (as per the TANGEDCO norms) - Supply, Installation, Testing and Commissioning of CPRI approved make of panel, cubicle type, Free standing, floor mounted, single front, 14 SWG CRCA sheet steel, enclosed separate compartment for each feeder, front operated, Powder coated, indoor type dust and vermin proof, hinged lockable doors, complete with electrolytic grade copper bus bars, internal wiring, colour coding, ferrules, Panel mounting MS Channels, fasteners, etc., RYB indication lamps, internal wirings, Digital voltmeter and Ammeter and other required accessories for the complete operation as per the Tangedco requirements. Necessary approval to be obtained from Tangedco before procurement including all associated control wiring. 1set of 250/5A CT with TNEB metering provision and 1 nos of 250A /5A CT for APFC.. For all items in this section, the rate includes necessary supports as required at site. No extra payment will be made for the same. Rate shall inclusive of factory witness test and all accessories, breakers , control wiring, models has to be followed as per in the technical specification.

Design, supply, fixing, testing and commissioning of cubicle type floor mounting switch board comprising of the following, the board shall be fabricated as per the detailed specification enclosed. Incoming 1 No: 250A 4P 35KA MCCB (Incoming EB source) 1 No: 250A3ph 4 pole Change Over Switch 1 No: 250A Four Pole MCCB (DG Incoming) Incomers shall have 1 set - Digital Combined meter (Having the parameters of Ammeter,Voltmeter and KWH meter). 1 set - LED type RYB,ON,OFF,TRIP indication lamps. Panel mounted Earth Leakage Relay with Leakage current display. 1 set -250 /5A CT CL 1.0 10VA. Outgoings: 2 nos - 200A TPN MCCB 3 nos - 160A TPN MCCB 1 nos - 100A TPN MCCB 9 Nos - 63A TPN MCCB. 2 Nos - Multifunction Meter digital type / MFM 5010 LED meter CI 0.5S with RS485. Note : All the Outgoing feeder shall be having 'on',off,trip' indication lamps..All switch boards shall be fabricated as per the detailed specification enclosed. Suitable size outgoing cable chamber and extra busbars should be provided for connecting the number of outgoing cables as per the schematic drawing. The board shall be fabricated for future extension of the panel board. Note:-The panel should be having provision to monitor the On, Off, trip status.

BUS BAR RATING: 250A TPN 16 KA for 1 sec. Aluminium bus bars (Current Density not less than 0.8A/Sq.mm.) with colour coated heat shrinkable PVC sleeves with DMC/SMC bus bar supports and suitable earth bus. Earthing : 25 x 6mm Aluminium flat . Cable Entry & Exit : Top. Cable Gland Plate : 3mm thick MS sheets Note: All MCCBs shall have rotary handle mechanism and spreader wherever necessary.

Design, fabrication, supply, erection, testing and commissioning of 55KVAR APFC PANEL-with cubicle type fully compartmentalized LT switchboards dust tight and vermin proof, fabricated out of 16SWG CRCA sheet, chemically treated and Powder Coated using 7 tank treatment of approved shade. The switchboard should have a set of suitably rated TPN aluminium busbar with specified current and fault level, insulated with heat shrinkable, colour coded PVC sleeves and supported using DMC/SMC supports. The design should be as per the standarads of the State Electrical Inspectorate. Name plate of panels/ DBs danger boards, incoming & outgoing feeders with ampere rating of switches/MCCB/MCB to be fixed on the front door above or below the respective switches. All MCCB's shall have O/C, S/C releases and extended rotary handle.

Incoming 160A 25kA TPN MCCB - 1 No. Metering RYB Indication Lamp with 6A SP MCB - 1 Set ACB ON/OFF/TRIP Accessories - 1 Set 8 Stage APFCR Relay - 1 No. Digital VAF Meter,1 No. 160/5A,15VA CL:1 CRCT - 3 Nos. Outgoings 63A TPN MCCB - 01 No. 40A TPN MCCB - 03 Nos. 25A TPN MCCB - 03 Nos. Capacitor 15 KVAR With 7%detuned reactor - 1 No Capacitor 10 KVAR With 7%detuned reactor - 2 No Capacitor 5 KVAR With 7%detuned reactor - 4 Nos Suitable Capacitor Duty Contactor for 15KVAR - 1 No. Suitable Capacitor Duty Contactor for 10KVAR - 2 Nos. Suitable Capacitor Duty Contactor for 5KVAR - 4 Nos. The panel shall be fabricated with proper ventilation and fan shall be provided with thermostat. Busbar 160A Al. Bus Bar

FLOOR DB PANEL-Design, fabrication, supply, erection, testing and commissioning of following cubicle type fully compartmentalized LT switchboards dust tight and vermin proof, fabricated out of 16SWG CRCA sheet, chemically treated and Powder Coated using 7 tank treatment of approved shade. The switchboard should have a set of suitably rated TPN aluminium busbar with specified current and fault level, insulated with heat shrinkable, colour coded PVC sleeves and supported using DMC/SMC supports. The design should be as per the standarads of the State Electrical Inspectorate. Name plate of panels/ DBs danger boards, incoming & outgoing feeders with ampere rating of switches/MCCB/MCB to be fixed on the front door above or below the respective switches. All MCCB's shall have O/C, S/C releases and extended rotary handle. The Panel Shall be IBMS Compatible

Incoming 160A 25kA TPN MCCB - 1 No. Metering RYB Indication Lamp with 6A SP MCB - 1 Set ACB ON/OFF/TRIP Accessories - 1 Set 8 Stage APFCR Relay - 1 No. Digital VAF Meter,1 No. 160/5A,15VA CL:1 CRCT - 3 Nos. Outgoings 63A TPN MCCB - 01 No. 40A TPN MCCB - 03 Nos. 25A TPN MCCB - 03 Nos. Capacitor 15 KVAR With 7%detuned reactor - 1 No Capacitor 10 KVAR With 7%detuned reactor - 2 No Capacitor 5 KVAR With 7%detuned reactor - 4 Nos Suitable Capacitor Duty Contactor for 15KVAR - 1 No. Suitable Capacitor Duty Contactor for 10KVAR - 2 Nos. Suitable Capacitor Duty Contactor for 5KVAR - 4 Nos. The panel shall be fabricated with proper ventilation and fan shall be provided with thermostat. Busbar 160A Al. Bus Bar

Fabrication, Supply, Erection, Testing and Commissioning of whether proof CRCA sheet steel powder coated MCCB Metering Panel Board, made up of 2mm powder coated, including 25x6mm aluminium bus bar provision of double door with industrial lock with of 6nos of 32A DP MCB, 6nos neutral link and 6nos of Earth link with TNEB Single Phase Serives connection Charges included 6 nos of Single phase Kwh meter serives connection three phase Multifunction meter with line indicators for erecting the Metering panel board complete etc., The rate is inclusive of Transport Charges etc. The above panel board is to be fixed on the floor with all interconnections and accessories, pedestal frame with concrete grouting or suitable to fix at concrete plinth as per the Corporation/ Highway department requirement.

FIRE PANEL - Design, fabrication, supply, erection, testing and commissioning of following cubicle type fully compartmentalized LT switchboards dust tight and vermin proof, fabricated out of 16SWG CRCA sheet, chemically treated and Powder Coated using 7 tank treatment of approved shade. The switchboard should have a set of suitably rated TPN aluminium busbar with specified current and fault level, insulated with heat shrinkable, colour coded PVC sleeves and supported using DMC/SMC supports. The design should be as per the standarads of the State Electrical Inspectorate. Name plate of panels/DBs danger boards, incoming.

Incoming 160A 25kA TPN MCCB - 1 No. Metering RYB Indication Lamp with 6A SP MCB - 1 Set ACB ON/OFF/TRIP Accessories - 1 Set 8 Stage APFCR Relay - 1 No. Digital VAF Meter,1 No. 160/5A,15VA CL:1 CRCT - 3 Nos. Outgoings 63A TPN MCCB - 01 No. 40A TPN MCCB - 03 Nos. 25A TPN MCCB - 03 Nos. Capacitor 15 KVAR With 7%detuned reactor - 1 No Capacitor 10 KVAR With 7%detuned reactor - 2 No Capacitor 5 KVAR With 7%detuned reactor - 4 Nos Suitable Capacitor Duty Contactor for 15KVAR - 1 No. Suitable Capacitor Duty Contactor for 10KVAR - 2 Nos. Suitable Capacitor Duty Contactor for 5KVAR - 4 Nos. The panel shall be fabricated with proper ventilation and fan shall be provided with thermostat. Busbar 160A Al. Bus Bar

PCC PANEL - Design, fabrication, supply, erection, testing and commissioning of following cubicle type fully compartmentalized LT switchboards dust tight and vermin proof, fabricated out of 16SWG CRCA sheet, chemically treated and Powder Coated using 7 tank treatment of approved shade. The switchboard should have a set of suitably rated TPN aluminium busbar with specified current and fault level, insulated with heat shrinkable, colour coded PVC sleeves and supported using DMC/SMC supports. The design should be as per the standarads of the State Electrical Inspectorate. Name plate of panels/DBs danger boards

Incoming 100A TPN MCCB - 1 No. 63A ATS - 1 No Metering RYB Indication Lamp with 6A SP MCB - 1 Set WITH MFM METER 63A/5A,15VA,CL:1 Outgoings 63A TPN MCB - 6 NOS Busbar 100A TPN Aluminium Busbar

Cable laying and End Terminations

Supply and Laying of 3 1/2 x 185 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and Laying of 3 1/2 x 120 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and Laying of 3 1/2 x 70 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and Laying of 3 1/2 x 25 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and Laying of 4C x 6sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and clamping of 3 1/2 x 50 sq.mm. PVC armoured LTUG cable on wall with suitable clamps.

Supply and clamping of 4C x 25 sq.mm. PVC armoured LTUG cable on wall with suitable clamps.

Supply and clamping of 4C x 16 sq.mm. PVC armoured LTUG cable on wall with suitable clamps.

Supply and clamping of 4C x 10 sq.mm. PVC armoured LTUG cable on wall with suitable clamps.

Supply and clamping of 3C x 10 sq.mm. PVC armoured LTUG copper cable on wall with suitable clamps.

Gland

Supply and fixing of brass cable gland for 3.5 x185 sqmm aluminium cable XLPE armoured LTUG cable with earth connection.

Supply and fixing of brass cable gland for 3.5 x120 sqmm aluminium cable XLPE armoured LTUG cable with earth connection.

Supply and fixing of brass cable gland for 3.5 x 70 sqmm aluminium cable XLPE armoured LTUG cable with earth connection.

Supply and fixing of brass cable gland for 3.5 x 50 sqmm aluminium cable XLPE armoured LTUG cable with earth connection.

Supply and fixing of brass cable gland for 3.5 x 25 sqmm aluminium cable XLPE armoured LTUG cable with earth connection.

Supply and fixing of brass cable gland for 4C x 25 sqmm aluminium cable XLPE armoured LTUG cable with earth connection.

Supply and fixing of brass cable gland for 4C x16 sqmm aluminium cable XLPE armoured LTUG cable with earth connection.

Supply and fixing of brass cable gland for 4C x10 sqmm aluminium cable XLPE armoured LTUG cable with earth connection.

Supply and fixing of brass cable gland for 4C x 6 sqmm Al Armoured cable LTUG cable with earth connection.

Supply and fixing of brass cable gland for 3C x10 sqmm COPPER cable LTUG cable with earth connection.

End Termination

Supply and providing cable end termination of 3 1/2 X 185 Sqmm PVC LTUG Aluminium armoured cable with necessary Aluminium cable sockets by crimping etc, with electrical connection complete.

Supply and providing cable end termination of 3 1/2 X 120 Sqmm PVC LTUG Aluminium armoured cable with necessary Aluminium cable sockets by crimping etc, with electrical connection complete.

Supply and providing cable end termination of 3 1/2 X 70 Sqmm PVC LTUG Aluminium armoured cable with necessary Aluminium cable sockets by crimping etc, with electrical connection complete.

Supply and providing cable end termination of 3 1/2 X 50 Sqmm PVC LTUG Aluminium armoured cable with necessary Aluminium cable sockets by crimping etc, with electrical connection complete.

Supply and providing cable end termination of 3 1/2 X 25 Sqmm PVC LTUG Aluminium armoured cable with necessary Aluminium cable sockets by crimping etc, with electrical connection complete.

Supply and providing cable end termination of 4 X 25 Sqmm PVC LTUG Aluminium armoured cable with necessary Aluminium cable sockets by crimping etc, with electrical connection complete.

Supply and providing cable end termination of 4 X 16 Sqmm PVC LTUG Aluminium armoured cable with necessary Aluminium cable sockets by crimping etc, with electrical connection complete.

Supply and providing cable end termination of 4 X 10 Sqmm PVC LTUG Aluminium armoured cable with necessary Aluminium cable sockets by crimping etc, with electrical connection complete.

Supply and providing cable end termination of 4 X 6 Sqmm PVC LTUG Al cable with necessary copper cable sockets by crimping etc, with electrical connection complete.

Supply and providing cable end termination of 3 X 10 Sqmm PVC LTUG cable with necessary copper cable sockets by crimping etc, with electrical connection complete.

Earthing

Earthing arrangements with GI Earth Plate including charcoal and salt with necessary excavation in all soils and to full depth as may be required and masonry work, re-filling the sides of foundation with excavated earth as per the standard specification and as directed by the Departmental Officers.

Supply, Installation, Testing and Commissioning of earthing station consisting of 600 x 600 x 3 mm. thick, copper Plate earth electrode, back filling with alternate layer of charcoal, salt, brick masonry work for chamber 450 x 450 mm. heavy duty CI cover, watering pipe, funnel and earthing conductor as per IS:3043 specification. All civil works required such as excavation in all types of soils, rocks, PCC Earthing Chamber foundation, reinstatement and making good the surface to match original, removal of surplus earth etc. are included.

Supply and run of 25mm x 3mm Copper Flat Down Condutor with necessary clamps / supports on wall / floor / ground for earth connection.

Supply and run of 25mm x 6mm Copper Flat Down Condutor with necessary clamps / supports on wall / floor / ground for earth connection.

External lighting

Supply, erection, testing and commissioning of 8 mtr free standing Single arm bracket 8 sided octagonally continuosly tapered strcutured pole with base plate of size 300 x300 x 12mm as per IS-875 along with 120W LED fitting with following specification. Bottom pole dia -130mm Top Pole dia -70mm Thickness of pole -3mm. The pole should be hot dip galvanized confirming to BESN ISO - 1461 with thickness of 65 Micron. Construction of pillar accommodating MCB and switch housed in weather proof box including wiring to the light fittings with 2 runs of 2.5 Sq.mm PVC insulated copper conductor, supplying and fixing 4 way 30 A rated terminal block loop in loop out cable arrangements coil earthing etc. the rate shall included for cable in and out throught pipe.The pole shall be as required by the Engineer in charge and complete with suitable pressure die cast aluminum housing also adhering to the above said specifications.Note:-The rate shall be quoted for complete set of Pole ,,Base foundation,Anchor fastener,internal wiring,earting materials,6A DP MCB box and all necessary accessories and civil cost etc should be provided as suitable to the requirement

Supply, Installation, Testing & Commissioning of 10W LED bollard light fittings Fitting. The Light Fitting should be powder coated with high pressure die-cast aluminium LED housing. And the LED fixed on die-cast aluminum heat sink for proper thermal management. and the operating voltage range 140 – 270V AC, provided with open and short circuit protection and input surge voltage protection.The driver should be Constant voltage constant current SMPS Protection of Fitting should be IP 66. LED having 50,000 burning hours with minimum 70% lumen maintenance and power factor 0.95. System consumption should be require with lumen package as per requirement. Crompton CAT REF : - LBLA3-10-CDL / Equivalent-(LANDSCAPE LIGHT). rate shall inclusive of necessary joint kit,glands,etc for loop in/out connection suitable to outdoor application .

The cable rack shall have runners rugs of suitable size, horizontal elbow, vertical elbow 90 Deg. Up vertical elbow 90 Deg. Down, re-deep, coupler plates, materials. The cable racks shall be suspended from ceiling supported from side walls in columns etc. with adequate size supporting angles / channels with fastners, welding, anchor bolts, nuts etc. The rack shall have suitable cable clamping arrangements etc.' Cable Tray /ladder should be powder quoted as match with ceiling colour as per PWD requirements. The rate shall inclusive of necessary Wedge anchors theaded rods,nuts & bolts, making clamp for rcc roof fix / perlin/Truss, cable tray clamps etc,(8 mm threaded rod supports shall be provided at not more than 2 mtr center to center and as per site requirement )

Perforated type

150mm x 50mm

300mm x 50mm

Supply and fixing Sheet steel of 14 SWG for connecting and Covering the tray(Quotation Enclosed)

Supplying and fabricating of MS structural steel supports for various applications using U channels, MS angle iron, bolts, nuts, anchor bolts etc., required for the work, cut to the size, bent to shape, welding, grouting etc., complete. Supports shall be powder coated with required colour for different system as mentioned above.

Internal Electrification

Supply and fixing of 8 way Vertical Triple pole and neutral MCCB sheet steel enclosure distribution board ( with MCCB incomer) with double door (metal) with 1 no.63A 4P MCCB switch as incoming and 8 nos.32A 3P MCB , as outgoing with suitable cable end box in flush with wall with earth connection only. Higher End

Supply and fixing of 7 segment 8 way 63A TPN MCB sheet steel distribution board (Higher end) with metal / acrylic door cover flush type /surface type fitted with busbars and neutral links with single / three phase MCB outgoings and seperate 4 way provision for accomodating one no. 4 pole incoming MCB / Isolator and another seperate 4 way provision for accomodating one no. 4 pole ELCB / RCD (totally 8 ways in one segment) (3x 8 ways in each segment) and seperate provision for MCB / Isolators ( totally 24 nos.) for sub incomers in 3 segments with lable holder and provison for taking up cable for size not less than 35 sq.mm. with the following in flush with wall with earth connection only

Supply and fixing of 4 way Vertical Triple pole and neutral MCCB sheet steel enclosure distribution board ( with MCCB incomer) with double door (metal) with 1 no.63A 4P MCCB switch as incoming and 2 nos.32A 3P MCB , AND 6nos 16A SP MCB as outgoing with suitable cable end box in flush with wall with earth connection only. Higher End

Supply and fixing of 8way Single pole and neutral MCB sheet steel enclosure with IP 42 protection distribution board double door with 1no. 32A DP MCB as incoming and 6Nos of 10A SP MCB for Outgoing on wall with earth connection only The MCB DB and MCB's should be with ISI mark. ( Like Standard make ) (SD-167)

Supply and fixing of double door type 12way SPN MCB board with IP 42 Protection with 63A 4 pole MCB isolator as incoming and 6Nos. 6 A to 32 A SP MCB as outgoing in flush with wall and making good of the concealed portion with earth connection. The MCB DB and MCB's should be with the ISI mark etc., all Complete, complying with relevant standard specification and as directed by the Departmental Officers.

Supply and fixing of 8 way Horizontal Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P MCB Isolator as incoming and 24 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End

Supply and fixing of 6 way SP DB of 16A / way with 16A DP switch with metal clad of 500V with fuse and neutral (side handle) on suitable angle iron frame work with trunking box MS cable entry box with PWD earthing.

Supply and fixing of 3 phase 4 wire 4 way ICDB of 16A per way with 32A TPNMC switch with suitable MS cable entry boxes trunking box and internal connections on suitable angle iron frame work with PWD earthing.

Supply and fixing of 20A DP plug and socket in sheet enclosure with 32A DP MCB in flush with wall with earthconnection (For AC Plug).

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (6 points / Coil) Higher End

Wiring, testing and commissioning of 3R x 1.5sqmm (22/0.3) and 1 run of 1.0 Sqmm PVC insulated SC unsheathed Cu.Conductor of 1100V grade in suitable PVC conduit pipe on concealed wall and ceiling with PVC accessories in flush with wall with manufacturers GI metal back box and 6A modular two way switch in flush with wall mounted on poly carbonate front plate with switch mounting metal parts, (Two way) and making good of the concealed portion with suitable colour for concealed staircase light point.Higher End.

Supply and run of 2 of 1.5 sq.mm. (22/ 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable gauge PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 1.5 sq.mm. (22/0.3) PVC insulated SC unsheathed copper conductor of 1100V grade and making good of the concealed portion with painting of suitable colour.

Supply and run of 2 of 2.5 sq.mm. (36/ 0.3)) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable gauge PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 1.5 sq.mm. (22/0.3)) PVC insulated SC unsheathed copper conductor of 1100V grade with painting of suitable colour (Circuit mains).

Supply and run of 2 x 4 Sq.mm PVC insulated SC unsheathed copper cable of 1100v grade in suitable PVC rigid pipe concealed in wall and Ceiling with connected PVC accessories with continuous earth connection of 1 of 2.5 Sq.mm copper cable and making good of the concealed portion with suitable color.

Supply and fixing of 1no.6A two module socket , 1 no. 6/16A two module socket, 1 no. 6A one module switch, 1 no.16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI) in flush with wall with connections. Higher End

Supply and fixing of 1 no.6/16A two module socket , 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End. (

Supply and fixing of 3nos.6A two module 5 pin socket , 3 nos. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End (For Computer Plug Socket)

Supply and fixing of 24W LED 2x2 Square type recessed fitting with LED with PVC unsheathed copper leads from terminal to the fitting

Supply and Fixing of surface mounted 20W LED batten comprises of thermaly conductive material, pre-wired with high efficency electronic driver,high translucent frosted diffuser gets glare free smooth light distribution. Model equivalent to Crompton, Philips or Bajaj.

Supply, installation, testing and commissioning of 18 W LED DOWN LIGHT FITTING with IP55 cool day light suitable for pole mounting, made out CRCA powder coated body, aluminium reflectors, poly methyl meth acrylate (PMMA) diffuser, glare free light, including electronic drivers, day light colour LED lamps, inter connecting wiring with suitable fixing clams, hooks as required including accessories all inclusive.

Supply, installation, testing and commissioning of 36 W LED 2X2 light fitting with cool day light, made out of CRCA powder coated body, aluminium reflectors, poly methyl meth acrylate (PMMA) diffuser, glare free light, suitable for recessed / surface mounting including electronic drivers, day light colour LED lamps, inter connecting wiring including accessories all inclusive.

Supply, installation, testing and commissioning of 28 W LINEAR LED light fitting with cool day light, made out of CRCA powder coated body, aluminium reflectors, poly methyl meth acrylate (PMMA) diffuser, glare free light, suitable for recessed / surface mounting including electronic drivers, day light colour LED lamps, inter connecting wiring including accessories all inclusive.

Supply, fixing, testing & commissioning of 10W LED bulkhead fixutre suitable for wall/surface mounting. The light fixture shall be grpahite grey powder coated pressure die-cast aluminium housing with diffused polycarbonate held with a silicon gasket. LED having 50,000 burning hours and power factor 0.95 with IP65. System consumption should be 10W Crompton CAT REF.,LBHE-10-CDL / Equivalent

Supply and fixing of 1200mm (48") AC ceiling fan complete with stepped electronic 300W regulator with 300mm down rod on the existing clamp

Supply and fixing of 300mm(12") sweep (lightduty) AC exhaust fan complete with necessary wall opening and making good of the wall. (Almonard / Crompton / Usha )

Supply, Installation, Testing and Commissioning of Wall mounted Split type 2TR Air conditioning unit with supply and installation of necessary acessories including necessary length of copper pipes,suitable type double boost voltage stablizer, pvc drain pipes, also includes necessary opening in the walls (if necessary)for the drain pipe routing and all other required accessories for the 2.0TR split type AC unit. (Make: 5star OG/Carrier/Voltas.

Supply, Installation, Testing and Commissioning of Wall mounted Split type 1.5TR Air conditioning unit with supply and installation of necessary acessories including necessary length of copper pipes,suitable type double boost voltage stablizer, pvc drain pipes, also includes necessary opening in the walls (if necessary)for the drain pipe routing and all other required accessories for the 1.5TR split type AC unit. (Make: 5star OG/Carrier/Voltas.)

Supply and laying of 5/8" and 3/8" Copper Pipe (Extra Beyod 3 Mtrs Supplied with AC unit)

Supply and Installation of 1" PVC water Drain pipe line for Airconditioners.

Supply, fabrication and fixing of MS stand for fixing outdoor Units.

Supply & Installation of 5KVA capacity Automatic Volatge Stabilizer with time delay relay (V guard/ Equivalent).

Lightning Protection System

Supply of Early Streamer Emission Air Terminal (ESEAT). Model: L The ESEAT has corrosion resistant stainless chrome body made up of AISI 316 grade of height 0.50 metres capable of working in hazardous atmosphere. The Air terminal is non-radioactive and requires no special licensing. The unit is fully autonomous (no battery, no external power supply is required), collects energy from the ambient electric field.The ESEAT model has been tested in a high voltage laboratory in accordance with NFC17 102 in order to measure the average gain in triggering. The average gain in triggering time (ΔTs) obtained during the lab test for the offered model is 60 μs. The ESEAT works on negative as well as positively polarized discharges. ESEAT has been tested for such discharges in Central Power Research Institute (CPRI). A dedicated tester is avilable to test the healthiness of the ESEAT on request (Page No. 37, Point No. 3 of Clause 8.6 of the Revised NFC 17-102 version 2011 ). ESEAT Model : L - Radius of protection : 86 Metres Level of protection considered for the Project-II level

Supply of Standard / Special Mounting Structure of height 4.5 mts. pipe, and 300 x 300 x 8mm MS plate, 3 mts. 48mm OD class C GI outer pipe,1.8 mtr, 38mm OD inner pipe, for roof mounting on concrete base and with FRP adapter

Supply and run of 25mm x 6mm GI Flat Down Condutor with necessary clamps / supports on wall / floor / ground for earth connection

Supply of Test Link Box for each Down conductor in order to disconnect the earth termination system to enable measurement of resistance

Supply and insallation maintenance free GI Earthing System comprising of 50mm dia and 2 mtr. long earth electrode of low carbon steel rod with 100 micron bonding and 25 kgs. of carbon based environment friendly backfill compound and suitable clamp

Supply and insallation Cabinet Type Class 1 and 2 Combined Model SPD to arrest surges and overvoltages in the power line due to lighning switching action etc. they must be installed in the incoming MCC panel / DB of the respective buling in parallel to the power circuit. Model:PSV4-12.5/400TT (3 phase power network)

Supply, Installation of 40KVA conventional type UPS with 30min battery backup with necessary interconnection cables, breakers, MS stand etc as required. The UPS Shall have 384V DC Three Phase Input and Three Phase Output with 64 nos of Exide 12V, "100AH" sealed maintenance free Battery. The battery Stand shall be Open type Powder coated Metal Battery Stand with insulated sheet and Battery to MCB to UPS ' U6' Nywin Cables each 5 meters, "U6" interconnecting Links - 64 Nos. The rate is inclusive of internal control cabling, Transportation, Insurance, Loading and unloading Charges. (Market Rate )

Supply, erection, testing, commissioning of 160 KVA DG Set With Diesel Engine developing suitable HP at 1500 RPM, 4 Cycle, 12 cylinder, water cooled, turbo charged, complete with standard Accessories confirming to latest emission control latest norms coupled to alternator rated at 160 KVA, 3 phase, 4 wire, 0.8PF (lag), 415V, IP 21 enclosure, class F/H insulation, with AVR, mounted on a channel iron base frame with foot mounting AVM pads, confirming to IS 4722, 300 Litters fuel tank, 1x12V 100AH battery with leads, AMF panel, Hospital type Silencer, with acoustic enclosure, control panel, inter connecting control cable, cable end termination, including necessary fuel tank system, lubrication system, cooling system, fabrication of exhaust M.S pipe system, supporting frame, structures arrangement, confirming to CPCB norms etc., synchronishing Panel and control wiring all inclusive. Note: (DG AMF with auto Synchronising control Panel). MARKET RATE

Supply and installation of Danger board as required by the Electrical authorities of size 500mm x 300mm of 16SWG MS of the Substation / Electrical room.The lettering shall be asper TNEBstandards.

Supply and laying of chequered rubber mat with IS mark suitable for 440V installation asper IS15652-class -A.600mm x 300mm size -Suitable to withstand the specifed voltage-test ertificate to be produced.

CCTV System

Supply of 4MP, Internet Protocol fixed BULLET CAMERA with following specification: ●1/2.5" Progressive Scan CMOS, ● 3840 × 2160 @15 fps,2.8/4 mm fixed lens,01 lux @ (F1.2, AGC ON), 0.028 lux @(F2.0, AGC ON), 0 lux with IR, H.265+, H.265, H.264+, H.264, 2 Behavior analyses ( Line crossing detection, intrusion detection) ● Face Detection ● 120dB WDR, ● BLC/3D DNR/ROI, IP67 complied ●On-board Storage - Built-in micro SD/SDHC/SDXC card slot, up to 128 GB, ● Shutter Speed 1/3 s to 1/100,000 s, ● 3-Axis Adjustment Pan: 0° to 360°, tilt: 0° to 100°, ● rotate: 0° to 360°, 2.8 mm, ● horizontal FOV: 102°, vertical FOV: 53°, diagonal FOV: 124°, ●Lens Mount M12 ● IR Range I5: up to 50 m, ● Image Settings Rotate mode, saturation, brightness, contrast, sharpness adjustable by client software or web browser, ● Power Consumption and Current-12 VDC, 0.7 A, max. 7.5W PoE: (802.3af, 36V to 57V), 0.3 A to 0.2 A, max. 9W ● Camera out fitted with metal housing so as to prevent the lens from damages during physical abuse. (Make: Dahua/Panasonic) (Rate as per quotation enclosed)

Supply, Installation, Testing and commissioning of 32 channel 2 SATA NVR, with Hard Disk Drive 2 nos, New logical and visualized GUI design Dual-OS design to ensure high reliability of system running, ANR technology to enhance the storage reliability when the network is disconnected, Configurable normal or hot spare working mode to constitute an N+1 hot spare system Video Input and Transmission, Connectable to the third-party network cameras Compression and Recording, H.265+ compression effectively reduces the storage space by upto 75%, Full channel recording at up to 12MP resolution HD Video Output  HDMI1 / VGA1 outputs provided  HDMI1 Video output at up to 4K ( 3840 × 2160 ) resolution Storage and Playback, Upto 16 SATA interfaces and 1 eSATA interface for HDD connection, Support upto 10TB capacity for each HDD, Smart search for efficient playback. and smart playback to improve the playback efficiency,Supports VCA search for fire/ship/temperature/temperature difference detection triggered video files, POS information overlay on live view and playback, POS triggered recording and alarm Network & Ethernet Access  Hik-Connect for easy network management, 2 Gigabit Ethernet network interfaces. (Make : Hikvision / Dahua / Sony).

Supply, installation, testing and commissioning of 4TB HARD DISK FOR NVR NETWORK VIDEO RECORDER with Necessary Clamp and Supports.

Supply, installation, testing and commissioning of 20 Metre HDMI Cable for Monitor with Necessary Clamp and Supports.

Supply, Installation, Testing and Commissioning of 55" smart LED TV with following specifications a) Full HD 1920 x1080 (4K monitor) b) IPS pannel c) Slim back light LED module d) 900 PMI e) Triple XD engine f) Dynamic scanning g) ANR h) True colour generator i) 8modes of picture j) picture wizardIII k) Real cinema 24P l) HDMI -3nos m) USB -3nos n) Built in LAN o) Magic remote p) Dimension 1242 x 724 x 55.1min(37). (Make: Sony/ LG /Samsung).

Supply, installation, testing and commissioning of 9U Rack for CCTV System with Fan, Necessary Clamp and Supports.

Supply, installation, testing and commissioning of RJ-45 I/O Socket with Necessary Clamp and Supports.

Supply, installation, testing and commissioning of 6 Core OFC(Indoor) with Necessary Clamp and Supports.

Supply, installation, testing and commissioning of 6 Core OFC(Outdoor) with Necessary Clamp and Supports.

Supply, installation, testing and commissioning of multi mode media converter with Necessary Clamp and Supports.

Supply, Installation, testing and commissioning of I/O Module Data Outlet box with cover plate, metal box and data socket.

Supply, laying, testing and commissioning of enhanced Cat 6 unarmoured Cable in suitable PVC rigid pipe on wall and ceiling with painting of suitable colour.

Supply, Installation, testing and commissioning of RJ45 Jack with ferol and other accessories as required.

Supply, Installation, testing and commissioning of 3 mtrs factory made CAT 6 cable with double side RJ 45 jack termination with necessary accessories.

Supply, Installation, testing and commissioning of fully managed 48 Port POE switch having 10/100/1000 layer -2 with 1G Uplink with all the accessories.

Supply, Installation, testing and commissioning of 48 Port patch panel with all necessary accessories.

Supply and Installation of 4U Rack with all necessary accessories.

Supply and Installation of cable manager of suitable dimension with divider, cover joint, Joint for top part and bottom part and all connected accessories.

Telephone

EPABX : Supply, installation, testing and commissioning of EPABX with built in 6 analog trunks, 4 digital extension(2 + 2 DXDP) and 96 analog extensions with future expantion facilities of IP trunk, SIP trunk, analog extension , digital extension & IP SIP extension with suitable channel.

Telephone Jack - Supply, installation, testing and commissioning of wall mounted telephone jack(RJ 11 socket) with GI box along with modular base and cover plate and terminating two pair telephone wires of the incoming line from telehone terminal connector located elsewhere.

Supply, installation, testing and commissioning of 100 pair jelly filled armoured Telephone Cable.

Supply and laying of 2 pair unarmoured 0.5mm telephone cable with 20mm PVC conduits concealed on wall and ceiling inlcuding all the accessories like clamps, saddles, pull boxes for telephone wiring.

Supply and fixing of 20 pair krone connector box in suitable FRP mounting box including termination of conduits, two pair telephone wire, incoming multicore telephone cables etc.

CALL POINT

21 Beds Nurse station with following facilities (a) Each room number display on Seven Segment Display (b) Voice pre recorded message to alert Nurse (c ) Mute switch to silance Audio. (d) Termination facility. (e) Built in power supply unit.

Supply of Call units (to be placed near Patient ) (a) Call Switch to request for Nurse (b) Reset Switch after attend the request (c) Call Request LED Indication

Supply of Pull Card unit with Switch(For Bed Ridden Patients)

Supply, run, testing and commissioning of enhanced Cat 6 Cable in suitable PVC rigid pipe on wall and ceiling with painting of suitable colour.

Testing and commissioning charges.

PA SYSTEM

PA Rack: Supply, Installation, Testing & Commissioning of sheet metal 17U rack (or vendor shall calculate and propose suitable rack) for mounting of Access Conrtoller & DVR's as per the technical specification with all mounting accessories etc.

Supply, Installation, Testing & Commissioning of Amplifier for PA system with RMS output (actual) 480 W as per the technical specification with all mounting accessories etc.

Box Type Speakers - Wall Mount Type: Supply, Installation, Testing & Commissioning of Cabinet type Speakers of 12 Watts Rated Power with 2 nos of Dual Cone High Sensitivity Loudspeaker Drivers, Opening Angle of 195o Horizontal and builtin 100 Volts Matching Transformer. The Speaker Cabinet shall be Black / White Color.

Supply and laying of FRLS PVC insulated 2 core 1.5 sq.mm. Armoured Copper Cable on ceiling / wall using fixing accessories like screws, plug, clamps, etc., as per standard methods and as directed by the Departmental Officers.

FA SYSTEM

Supply, Installation, Testing & Commissioning of UL listed and FM approved 4 Loop Intelligent Addressable Fire Alarm control panel having the capacity of 252 devices / detectors per loop any combination ( Minimum of 200 detectors in each loop). The panel shall have 32 bit Central processor with 5000 Event History logging with On Line & Offline reports. and having large, 6" (15.2 cm) (1200 x 800 pixel) color liquid-crystal display (LCD), touch screen and LEDs for displaying system status. Panel should support Class X circuits as per NFPA72. LCD Display status highlights Alarm events appear in red; Trouble events appear in yellow; Supervisory events in blue, and Security events in magenta.The panel shall have 12 Amps inbuilt power supply having charging capacity of maximum 100AH Lead Acid battery. In case of networking, the panel shall have network card included inside the panel for RS485 communication with other display devices like Graphic screen, repeater panel etc. The panel shall be modular and shall have the capacity of expanding upto 10 Loops and 2500 devices/detectors maximum. The panel shall support smart degrade mode operation and shall have battery backup of 24 hrs in normal condition and 30 minutes in Alarm condition. can view a graphics map, which can show a simple building floor plan. On the map, the user will see an icon indicating the location of the event in the building in addition to a 'You-Are-Here' symbol to tell the responding person exactly where they are in the building in relation to the event.

Supply, installation, testing and commissioning of Electronic Hooter / Sounder providing on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers (Make: Ravel / Equivalent)

Supply, installation, testing and commissioning of Manual Call Point (MCP) providing on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers. (Make: Ravel / Equivalent)

Supply, installation, testing and commissioning of Conventional Smoke Detector suitably mounted on ceiling with MS juction box / false ceiling using fixing accessories like screws, plug, clamps, etc., as per standard methods and as directed by the Departmental Officers. (Make: Apollo / Equivalent).

Supply, Installation, Testing and Commissioning of Intelligent Addressable photoelectric Heat detector with base plate.

Isolator Module: Supply, Installation, testing and commissioning of Isolator Module with indicating lamp, mounting base and all other mounting accessories complete as required.

Control Module for Hooter: Supply, Installation, testing and commissioning of Addressable Control Modules for activating hooters with all the mounting accessories complete as required. One CM shall provide one activation signals.

Control Module for PA Integration: Supply, Installation, testing and commissioning of Addressable Control Modules for overriding PA system with all the mounting accessories complete as required. One CM shall provide one activation signals.

Monitor Module: Supply, Installation, testing and commissioning of Addressable Monitor Modules for Interfacing PFC/Dry Inputs of Fire Pump/Chiller/AHU Signals, Sprinkler Line Flow Switch Status.

Supply and laying of FRLS PVC insulated 2 core 1.5sq.mm.(Red colour) Armoured Copper Cable on ceiling / wall using fixing accessories like screws, plug, clamps, etc., as per standard methods and as directed by the Departmental Officers..

The Lift Shall have additional following specifcation: 1.Battery operated Emergency Light and alaram bell 2.Call register signal and VF door operator 3.Landing push button landing door frames 4.Automatic resuce device 5.Vandal proof S.S button with S.S cover 6.Braille button 7.Full car operating panel 8.Dot matrix led D& P indicators in car & landing orange colour 9.Floor annunciaton with music 10.fireman switch 11.False ceiling in car 12.Fire rating of landing door 2Hrs 13.Infra red screen 14.Overload warning indicator 15.Scaffloding 16.3Way intercom /press and speak phone 17.Free service for one year 18.Pit ladder 19 SS handrail 20.Lift license 21.Minor builders work 22 including additional Two Year warranty

The Lift Shall have additional following specifcation: 1.Battery operated Emergency Light and alaram bell 2.Call register signal and VF door operator 3.Landing push button landing door frames 4.Automatic resuce device 5.Vandal proof S.S button with S.S cover 6.Braille button 7.Full car operating panel 8.Dot matrix led D& P indicators in car & landing orange colour 9.Floor annunciaton with music 10.fireman switch 11.False ceiling in car 12.Fire rating of landing door 2Hrs 13.Infra red screen 14.Overload warning indicator 15.Scaffloding 16.3Way intercom /press and speak phone 17.Free service for one year 18.Pit ladder 19 SS handrail 20.Lift license 21.Minor builders work 22 including additional Two Year warranty

RSK CONSTRUCTION AND PROJECTS

S J INFRA