ADDN / ALTN AND SPECIAL REPAIR TO JCOs / ORs MD ACCN AT BENGDUBI MIL STATION UNDER GE BENGDUBI

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for roughening the surfaces of old concrete floor by picking, sweeping, cleaning and washing down with water to remove dust and brushing neat cement slurry with 3.0 kg of cement per Sqm complete all as specified and directed.

M&L for non skid ceramic (coloured) joint free tiles 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floor etc set and jointed in neat cement slurry over 15mm thick screed bed or bedding layer in CM (1:6) as in floor and pointed in white or coloured cement to match as in floor complete all as specified and and directed.

M&L for non skid (coloured) joint free ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.18 Sqm but n. exc. 0.38 Sqm as in, vertical surfaces, of skirting etc. set and jointed in neat cement slurry over 10 mm thick rendering in CM (1:4) and pointed in white or coloured cement to match as in floor complete all as specified and directed.

M&L for non skid (coloured) joint free ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.11 Sqm but n. exc. 0.18 Sqm, in floors etc. set and jointed in neat cement slurry over 15mm thick screed bed or bedding layer in CM (1:6) as in floor and pointed with white or coloured cement to match complete all as specified and directed.

M&L for glazed ceramic colour tiles/digital elevation tiles of size 300X 450 X 7-8mm or 300X 600 X 7-8mm thick as on vertical surfaces of wall such as skirting, dado, riser etc. in Bath, WC and Kitchen set and jointed in neat cement slurry over 10 mm thick rendering in CM (1:4) and pointed in white or coloured cement to match complete all as specified and directed.

Dismantling Stone slabs and tiles of any description or thickness laid, bedded and jointed in any mortar in floors, aprons etc. complete all as specified and directed.

M&L for 18 to 20 mm thick granite (of any type) work (table rubbed and polished) in skirting, kitchen platform / dado and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and including 20 mm thick cement plaster (1:4) including rounding and polishing the exposed surfaces of granite complete all as specified and directed.

M&L for machine cut kota stone slab flooring 18-20 mm thick (table rubbed) over 20mm thick cement screed bed using cement mortar (1:6) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (mirror finish) complete all as specified and directed.

M&L for machine cut kota stone slab 18-20 mm thick (table rubbed) as in riser of step, skirting, dado, including 10mm thick cement screed bed using cement mortar (1:4) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (mirror finish) complete all as specified and directed.

Taking down chowkat with shutter exc 1.5 sqm and n.exc. 4.00 sqm each (without taking off shutters from the frame), including cutting holes for removing the hold fast etc complete all as specified and directed.

Taking down chowkat with shutter not exc 1.5 sqm each (without taking off shutters from the frame), including cutting holes for removing the hold fast etc complete all as specified and directed.

Taking down of wooden door shutter of any description area exceeding 1 sqm and n.exc. 2 sqm each and removing from the site complete all as specified and directed.

S&F for 1.25mm thick pressed steel frames of size 165 x60 mm for doors with one or more rebates including supply and fixing necessary lugs, hinges, lock strike plate, etc. including one soap coat of priming complete all as specified and directed.

S&F for 1.25mm thick pressed steel frames of size 105 x60 mm for doors with one or more rebates including supply and fixing necessary lugs, hinges, lock strike plate, etc. including one soap coat of priming complete all as specified and directed.

S&F Solid PVC frame (Single Rebated) of size 60mm x 30mm made out of solid PVC foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete all as specified and directed. Note : Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life.

S&F for Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification and drawing complete all as specified and directed.

S&F for 35 mm thick factory made flush shutter, solid core construction, with block board core and plywood face panel, commercial type on both side etc complete all as specified and directed.

S&F for 25 mm thick factory made flush shutter, solid core construction, with block board core and plywood face panel, commercial type on both side etc complete all as specified and directed.

S&F for 2nd class hard wood 35 mm thick made glazed and skeleton shutters open rebated and prepared to rceieve glass, gauze,etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass,etc, size of members of shutters as specified in SSR Part-1, Section 8, clause 8.24 (a) kiln seasoned and chemically pressure treated complete all as specified and as directed.

S&F for Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete for Fe 410 (grade E-250 quality -A) complete all as specified and as directed.

S&F for Framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walkways; railings; frame work of water tanks and similar work conforming to Fe 410, Gde-E-310 complete all as specified and and directed.

S&F for Powder coated (thickness of powder coating not less than 50 micron) anodised aluminum frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and and directed.

S&F for powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, window & ventilator including poviding and fixing hinges/pivots / sliding any making provision for fixing of fittings whereever required incuding the cost of EPDM rubber/neoprene gasket required (fittings shall be paid for separately) wth extruded built up standard tubular sections/appropriate Z sections and other secitons of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, incl necessary filling up the gapsat junctions, i.e at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Alumiuium sections shall be smooth, rust free, straigth, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/paneling, CP brass/stainless steel screws all complete as per architechtural drawings and as directed.

S&F for 4 mm thick sheet glass, ordinary quality and glazing with oil putty in squares in exc 0.5 sq.m in each pane etcc omplete all as specified and as directed

S&F for stainless steel wire cloth 0.36 mm nominal dia wire & average width of aperature 1.40 mm fixed with stainless steel wire staples complete all as specified and directed.

S&F for aluminium anodised barrel tower bolts of extruded section 200 mm long complete all as specified and directed.

S&F for aluminium anodised barrel tower bolts of extruded section 150 mm long complete all as specified and directed.

S&F for aluminium handles 150mm size cast type anodised complete all as specified and directed.

M&L for Aluminium alloy, anodised sliding door bolt of length 300mm long, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

S&F for ball catches with 8mm dia steel ball and brass body and skirting plate including letting in and fixed complete all as specified and directed.

S&F for continuous (piano hinges) 30mm width of flap Paino hinges, mild steel bright finish (width of flap 30mm) complete all as specified and directed.

S&F for 75 mm butt hinges stainless steel complete all as specified and directed.

Dismantling Asbestos Cement (Corrugated, Semi corrugated etc.) sheets in roof coverings including ridges, hips, valleys and flashings complete all as specified and directed.

S&F for pre-painted coloured trapezoidal profiled Galvalume/Zincalume sheet with min 0.50mm TCT conforming to IS-513 (AZ-150 GSM, AL Zn alloy metalic coating 550 MPA yield stress as per AS-1397), as in roof covering/ cladding to wall fixed with self tapping screws colour /exterior coat of silicon modified polyster/ BHP X RW paint system 20 micron top coat applied over 5 micron primer and a 5 micron polyster back coat applied over 5 micron primer, all fixed with Galvanised self drilling self-tapping fastener (12-14 x 55 with EPDM seals ) complete all as specified and directed.

S&F for pre-painted coloured plain sheet profiled Galvalume/Zincalume sheet with min 0.50mm TCT conforming to IS-513 (AZ-150 GSM, AL Zn alloy metalic coating 550 MPA yield stress as per AS-1397), as in roof covering/ cladding to wall fixed with self tapping screws colour /exterior coat of silicon modified polyster/ BHP X RW paint system 20 micron top coat applied over 5 micron primer and a 5 micron polyster back coat applied over 5 micron primer, all fixed with Galvanised self drilling self-tapping fastener (12-14 x 55 with EPDM seals ) complete all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards /slabs/ blankets any thickness including cover fillets complete all as specified and directed.

M&L for aluminium anodised snap grid frame work for false ceiling including Hangers 4 mm dia. G.I. (upto 1800mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and as directed.

M&L for 4 mm thick Non asbestos fibre cement disigner pre-painted building boards fixed or laid/ inserted to timber/GI/Aluminium framework with screws complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for grils.rails etc connection complete all as specified and directed.

M&L for Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates, febrication Fe-410W(GdeE-250) quality A complete all as specified and directed.

Taking down cement plaster on wall & ceiling of any description including raking out joints, hacking for key and scrubbing down with water etc complete all as specified and directed.

M&L for rendering 5mm thick in cement mortar 1:3 on ceiling, soffits of slabs, chajjas, columns and beams etc and finished the plastered surface even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick in CM (1:6) on fair faces of brick work or concrete surface finsihed fair and even without using extra cement complete all as specified and as directed

M&L for rendering 20mm thick plaster in two layers (i.e. 10mm and 10mm) in CM (1:4) mixed with water proofing compound as per manufacturer instruction on top layer finished on fair face of brick or concrete surface finished complete all as specified and directed. Note:- WPC shall be measured and paid seperately under respective item of BOQ.

Supply only liquid water proofing compound conforming to IS: 2645 - 1975 specification complete all as specified and directed.

Taking down steel tubing & connections including cleaning for refixing serviceable pipe or removal balance pipe of 15 mm dia bore complete all as specified and as directed

Taking down steel tubing & connections including cleaning for refixing serviceable pipe or removal balance pipe of 20 mm dia bore complete all as specified and as directed

Taking down steel tubing & connections including cleaning for refixing serviceable pipe or removal balance pipe of 25 mm dia bore complete all as specified and as directed

Supplying and laying of 20mm CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified

Supply, laying, jointing and testing GI water tubing 20mm bore, medium grade, galvanised with all fittings and fixtures laid in trenches, floor, wall, ceiling complete all as specified and directed.

Supply, laying, jointing and testing GI water tubing 25mm bore, medium grade, galvanised with all fittings and fixtures laid in trenches, floor, wall, ceiling complete all as specified and directed.

Dismantling water tanks of capacity exc 500 but not n.exc 1000 ltrs complete all as specified and directed.

S&F for rotational moulded PVC water storage tank 500ltrs capacity conforming to IS-12701(1989) cylindrical vertical type double-layered with closed top including inlet,outlet and wash out holes of approved make hoisted and fixed in position all as specified in SSR Part I etc completge all as specified and as directed

S&F for 20 mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed. (Minimum weight 15mm-142 gms/ 20mm-210 gms/25mm-455gms/ 40mm- 690 gms) etc complete all as specified and as directed

S&F in repair Gun metal, globe Gate Valves with iron wheel head of 25 mm bore complete with all accessories complete all as specified and directed.

S&F Hard drawn steel wire fabric in available size weight not exc 4.00 Kg /sqm fixed in tank caging including welding, riveting, framing etc complete all as specified and as directed

Taking down existing un-servicable waterproofing treatment from roof slab and slab and cleaning the roof slab by wire brash and removing WPT felt beyond the MOD premises etc complete all as specified and as directed.

M&L for water proofing treatment to roof slab with the following course of treatment/ specification complete all as specified and directed :- (i) Cleaning top surface of floors /slabs and laying 25 mm thick (avg) PCC of grade M15 (Nominal mix), mixed with WPC as per manufacturer’s instruction laid in slope 1:20 towards spouts including coveting corners. (ii) 10 mm thick plastering in CM (1:4) on sides mixed with WPC as per manufacturer’s instruction. (iii) Application of waterproofing Coating : Providing and applying a single component High build fibre Reinforced Acrylic Waterproofing render for roofing system to be applied by brush, of three coats at minimum dry film thickness of 1 mm, which should cure by reaction with atmospheric moisture to give a tough elastomeric waterproof membrane. Solid Content - 70%, Tensile strength ASTM D 412-1.10 Mpa, Elongation ASTM D12-100%, Resistance to ageing due to - 1000hours, UV radiation ASTM D4587 E - No Change, Rapid Chloride Penetration ASTM c 1202 - Very low, Pull off adhesion ASTM D541 - 0.92 Mpa, Resistance to Algae growth ASTM D 5589-97 - Passes, Zero rating, Permeability (mm) (BSEN 12390 part 8) -n 5.0, Water vapour transmission (ASTM E 96) - 6.0g/m2 h

Demolition of brick work built in cement mortar of any description complete all as specified and directed.

M&L for brick work with fly ash Bricks straight or curved on plan in CM 1:4 as in half brick thick walls complete all as specified and as directed

M&L for brick work with fly ash Bricks straigh or curved on plan exc 6m mean radius built in cement mortar 1:6 by using old size bricks complete all as specified and directed.

S&F in repair white vitreous china wash basin white flat back size 550x400 (Oval shape) excluding taps but including 32 mm dia chromium plated waste fitting and PVC waste pipe 610 mm long and MS brackets complete all as specified and as directed

S&F in repair 1 mm thick sinks made of stainless steel kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm etc complete all as specified and as directed

S&F for 0.5mm thick stainless steel plate rack of overall size 24x 30 x 10 inch of standard quality and shapes complete all specified and as directed.

S&F in repair vitreous china wash down water closet pan (pedestral pattern), white including connection trap and to flushing pipe, anti-syphnoge pipe etc complete including PVC seat cover of same make complete all as specified and directed.

S&F in repair PVC valveless syphonic action type flushing cistern low level of 10 Ltr capacity white with inlet ball valve, float, flushing bend & handle including brackets, suitable for both Indian Type Water Closet & Europeon Type Water Closet including brackets & connection to pipe etc complete all as specified and as directed

S&F in repair for brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed.

S&F in repair chromium plated shower roses 125 mm size with or without swivel joints of standard size including fixing to 15mm steel pipe or union complete all as specified and as directed

S&F for wall mixer, cast copper alloy with capstan head, chromium plated screwed down, high pressure with or without lettered "hot" or "cold" with long screwed shank and fly nuts screwed for iron pipe of 15mm bore complete all as specified and directed.

S&F in repair bib tap (Long body) fancy type cast copper alloy chromium plated with crutch or butterfly handle screwed down screwed for iron pipe or brass ferrule or fixed for 15 mm dia bore pipe complete all as specified and as directed

S&F chromium plated sink mixture with or without lettered hot or cold including joints to steel pipes or unions and plugging and screwing complete all as specified and as directed.

S&F for 50 mm high density polythyene pipes of pressure rating 6 Kg/f/CM2 fixed to walls, ceilings or in floors etc complete all as specified and directed.

S&F in repair chromium plated two way angle stop cock 15mm dia complete all as specified and directed.

S&F chromium plated angle stop cock 15mm dia complete all as specified and directed.

S&F for central hole basin mixer swan neck pillar tap cost copper alloy with capstan head chromium plated , screwed down high pressure with or without lettered hot or cold with long scewed shank and fly nuts screwed for iron pipe of 15 mm bore complete all as specified and as directed

S&F for PVC connection of 45 cm length including brass nuts complete all as specified and as directed.

S&F in repairs 32mm bore Low density polyethylene (LDPE) pipes of pressure rating 6kgf/sq. cm etc complete all as specified and as directed.

Dismantling of cast iron or reinforced concrete drain pipe up to 100 mm dia, jointed in cement mortar and taking out trenches if reqired etc complete all as specified and directed.

Taking down PVC rain water pipes (any size or pattern) including fittings from wall, treches of any description complete all as specified and directed.

S&F for 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floor with necessary clamps and bolts etc complete all as specified and directed.

S&F for 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floor complete all as specified and directed.

S&F for 75mm bore PVC (SWR) Bends, diminishing pieces or tapers of any radius complete all as specified and directed.

S&F for 110mm bore PVC (SWR) Bends, diminishing pieces or tapers of any radius complete all as specified and directed.

S&F PVC (SWR) Branch pieces, single (single Y) equal or unequal of pipe 110mm bore complete all as spcified.

S&F PVC (SWR) Branch pieces, single (single Y) equal or unequal of pipe 75mm bore complete all as spcified.

S&F for 75 mm bore PVC (SWR) junction single (Single `T') equal or unequal with access door complete all as specified and directed.

S&F for 110 mm bore PVC (SWR) branch piece single (Single `T') equal or unequal with access door complete all as specified and directed.

S&F for 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls with necessary clamps and bolts etc complete all as specified and directed.

S&F in repair for stack clamps out of 50 mm by 5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 75 mm bore of pipe complete all as specified and directed.

S&F in repair for stack clamps out of 50 mm by 5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 110 mm bore of pipe complete all as specified and directed.

S&F for 110mm bore PVC SWR vent cowl complete all as specified and directed.

BLANK

BLANK

S&F for PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement in cement concrete type B1 (1:2:4) ,in repairs and including waterleak proof treatment complete all as specified and directed.

S&F for PVC (SWR) floor trap, plain with grating 75mm including jointing to wast pipe fixed in cement concrete type B1 (1:2:4) ,in repairs and including waterleak proof treatment complete all as specified and directed.

Demolition of cement concrete (un-reinforced ) of any description & in any position not specifically provided for complete all as specified and as directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description & in any position not specifically provided for complete all as specified and as directed.

M&L for 75mm thick PCC (1:3:6) type C2 (using 40mm graded crushed stone aggregate) as in plinth protection, finishing cement concrete surface even & fair without using extra cement including filiing the joints with bitumen & sand in 1:2 proportion etc complete all as specified and directed.

M&L for Reinforced cement concrete (Nominal Mix) type A1 (1:1.5:3 ) using 20 mm graded crushed stone aggregate as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

Use and waste of Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed.

M&L for TMT bar 10 mm dia and over cut to length, bent to shape required and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for TMT bar 5 mm dia and over, cut to length, bent to shape required, including cranking and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips as in binders, stirrups etc complete all as specified and directed.

M&L for Reinforced cement concrete Nominal Mix type A1 (1:1.5:3 ) using 20 mm graded crushed stone aggregate as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for Reinforced cement concrete Nominal Mix type A1 (1:1.5:3 ) using 20 mm graded crushed stone aggregate as in Chajjas complete all as specified and directed.

Use and Waste Formwork to chullah hoods, chajjas, troughs and similar items including edges complete all as specified and directed.

Use and Waste Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.

M&L for 18/19mm thick Pre laminated particle board interior grade both sides laminated for cup board kitchen cabinet etc complete including beading complete all as specified and as directed.

M&L for IInd class hardwood Plain fillets. square,rectangular or triangular in section, clean sawn, secured with nails or brads of sectional area exc 13Sqcm and n exc 25 Sqcm complete all as specified and as directed.

M&L for providing plain cement concrete type C-1, 1:3:6, (using 20 mm graded crushed stone aggregate), as in copings, bed block for filing hollow space of steel chowkhats, fixing of hold fast, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles & throating including necessary form work as required complete all as specified and directed.

M&L for cement concrete 1:2:4 type, B1 using 20 mm graded crushed stone aggregates as in copings, Chajja kerbs, roof padding/staging of water tank etc including necessary fromwork, weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed

S&F for mild steel Helical door spring 300mm long ordinary rat tail type incl roaller & roller plate complete fixed with screws to wooden frames or with welding to steel frames complete all as specified and directed.

M&L for 15mm thick cement plaster in cement mortar 1:6 in mixed with water proofing compound as per manufacturer instruction on top layer of 5mm and finished even and smooth surface without using extra cement as in sunken floor treatment etc complete all as specified and as directed. Note : WPC shall measured and paid saperately under respective item.

M&L for cement concrete 1:5:10 type E-2 using 20mm graded stone aggregate as in sunken portion of WC etc complete all as specified and as directed.

Cutting chases, pinning in making good to facing where required and pointing in cement mortar 1:3 to ends and edges of landing ,steps,cills,sunshade,shelves,lintel,etc and cutting chases for concealed water tubing or concealed conduit wiring etc, making good, cutting not exc 10cm girth complete all as specified and as directed.

S&F for decorative stainless steel curtain rod of wooden finish 20mm dia thickness not less than 0.75mm fixed with curtain rod holder fixed in walls wih screws and finials caps with 06 Nos of curtain ring per Rm complete all as specified and directed. Note: Curtain rod holder and finials cps will be measured and paid seperately under supply only rates.

Supply only decorative stainless steel curtain holding bracket suitable for holding 20mm curtain rod heavy duty complete as specified and directed.

Supply only decorative stainless steel finial end cap suitable for curtain rod of 20mm dia as approved complete as specified and directed

S&F in repair health faucet (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25m long flexible tube and ABS wall hook includung making connection and fixed in position complete all as specified and directed.

M&L for preparing newly plastered surface of wall and applying two coats of oil bond acrylic-based distemper of shade as approved by GE over a coat of primer and a coat of 2mm thick wall care putty on surfaces of wall complete all as specified and directed. Note:- 1. Application of new finishes to be carried out mechanically by authorised applicator and as per the manufacturer's instructions. Please refer Smart Painting clause mentioned in Particular Specification.

M&L for complete removal of existing treatment of wall and applying two coats of oil bond acrylic-based distemper of shade as approved by GE over a coat of primer and a coat of 2mm thick wall care putty on surfaces of wall complete all as specified and directed. Note:- 1. Application of new finishes to be carried out mechanically by authorised applicator and as per the manufacturer's instructions. Please refer Smart Painting clause mentioned in Particular Specification.

M&L for preparing newly plastered surface of wall applying priming and finishing walls with acrylic smooth exterior paint of required shade: New work (Two or more coat applied @ 1.67 ltr/10 Sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) and including 2mm thick wall care putty complete all as specified and as directed.

M&L for complete removal of existing treatment of wall and applying priming and finishing walls with acrylic smooth exterior paint of required shade: Two or more coat applied @ 1.67 ltr/10 Sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm and including 2mm thick wall care putty complete all as specified and as directed.

M&L for preparing new plastered surface of ceiling surface and applying three coats of white wash etc complete all as specified and as directed.

M&L for preparing old plastered surface of ceiling and applying one coat of white wash etc complete all as specified and as directed.

M&L for preparing new wooden surface of any description, not other wise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer etc complete all as specified and as directed.

M&L for preparing of old painted surfaces of wood & wood based surface of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for Preparation of new steel and iron surfaces of any description, over 10 cm in width or girth , not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide primer etc complete all as specified and as directed.

M&L preparation of old painted surfaces of steel surface of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

Cleaning of vegatation of height upto 300 mm from roof, slab, wall, chajja etc and digging out roots etc n exc and filling holesand finish the surfaces with cement morter (1:3) complete all as specified and as directed.

M&L for providing and injecting chemical emulsion for post constructional Antitermite treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc complete all as specified and as directed.

M&L for ATT along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 ltr linear metre including drilling and plugging holes etc in apron complete all as specified and as directed.

M&L for ATT of soil under existing floors using emulsion @ one litre per hole, 300 mm apart dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and as directed.

S&F for CPVC Brass Elbow for 20 mm (OD) pipes complete all as specified and as directed.

S&F for CPVC Brass Tee on 20 mm (OD) pipes complete all as specified and as directed.

Supply and fix CPVC Male Brass Threaded Adaptor (MTA/ MBTA) ) on 20 mm outer dia pipes.

S&F for CPVC Female Brass Threaded Adaptor (FTA/ FBTA) on 20 mm (OD) pipes complete all as specified and as directed.

M&L for Second class hardwood as in scantling framed & fixed clean swan complete all as specified and as directed.

M&L for making good under cills over arches, lintel and bresummers, including all pinning when nessesary with using cement mortar 1:6 complete all as specified and as directed.

Removing & Hacking of existing concrete Carefully by low impact high frequency hammer OR by manual chipping without damaging the existing concrete or control sand blasting including cleaning the surfaces by air jet etc. complete all as specified and as directed. Note:- Method of measurement: Per Sqmt of breaking area of concrete.

M&L for rusted metal (iron base) apply reebaklens RR with brush for complete wetting of rusted metal surface and allowed to react it for 16-24 hours. After 24 hours, a white layer will appear which will protect further corrosion of metal / steel for about 5-7 days. Before applying protective coating, the surface should be wire brushed and thoroughly cleaned for dust with dry cloth complete all as specified and as directed.

M&L for Providing and applying two coats of Nitozinc Primer a two component epoxy zinc rich primer or equilvalent product on the properly cleaned and prepared steel bars after the required chipping and cleaning of the concrete surface as per the manufactures specification complete all as specified and as directed.

M&L for Providing and applying structural grade long pot life epoxy bond coat of Nitobond EP Std prior to building up of section with any type of mortar / concrete to ensure bond between old concrete and new concrete by brush application as per the mgf specifications complete all as specified and as directed.

M&L for concrete surface with single component, fibre reinforced shrinkage compensated, polymer modified structural grade repair mortar like Fosroc Renderoc SP 40 or equivalent at a thickness of 40mm. The repair mortar should have a compressive strength 45 N/mm2, flexture strength 7 N/mm2 and tensile strength 2.5 N/mm2 at 28 days complete all as specified and as directed.

M&L for PCC 1:3:6 type C-2 (40mm graded crushed stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed.

Demolition & breaking up drain pipes (salt glazed ware, AC or reinforced concrete) set in cement mortar, internal dia of pipe up to 150mm complete all as specified and directed.

M&L for concrete bed for sewer line packing under and haunching against the sides of the new pipes with PCC (1:3:6) type C-2 with (using 40 mm graded crushed stone aggregates) for the 150 mm dia (Internal) of sewer pipe lines complete all as specified and directed.

M&L for 150 mm dia Double Wall Corrugated(DWC) HDPE pipe, grade 'A' pressure rating rating SN-8 laid in trenches and jointed complete all as specified and as directed

M&L for rendering 15 mm thick in CM (1:4) on fair faces of brick work or concrete surface finsihed even and smooth with using neeru finish etc complete all as specified and as directed.

M&L for TMT bars 6 to 8 mm dia dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia, or securing with clips etc complete all as specified and directed.

Surface dressing n.exc 0.15 m deep and getting out in soft/loose soil complete all as specified and directed.

Excavation in trenches in soft/loose soil not exc. 1.5 metre wide and not exc. 1.5 metre in depth and getting out for foundation, manholes, taking up / laying under ground electric cable, drain etc complete all as specified and directed.

Returning, filling in, including spreading levelling watering and well rammming in layers not exceeding 25 cm in depth complete all as specified and directed.

Removing surplus soil to a distance not exceeding 50 mtr and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm complete all as specified and directed.

M&L for PCC (1:4:8) type D-2 (using 40 mm grade crushed stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

M&L for Hardcore of gauge n exc. 63mm with broken stone or boulders, deposited, spread and levelled in layers not exc. 15cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for 100mm thick PCC (1:3:6) type C2 (using 40mm graded crushed stone aggregate) as in hardstanding, ramp etc complete all as specified and directed.

M&L for structural steel work as in plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment, Fe 410 -W (Gde- E- 250) quality - A, complete all as specified and directed.

M&L for Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 10cm n.exc 15cm long of neck from 11 mm to 15 mm complete all as specified and directed.

M&L for PCC Type C2 (1:3:6) using 40mm graded crushed stone aggregate as in surface channels and drains, sub base etc complete all as specified and directed.

M&L for PCC Type B2 (1:2:4) using 20mm graded crushed stone aggregate as in surface channels and drains, sub base etc complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc complete all as specified and directed.

M&L for Pre-cast cement concrete (1:2:4) type B-1 using 20 mm graded stone aggrgates ) set in CM 1:4 as in landing, cover slab(for manholes etc) chulla hoods, chajjas, water trough, mangers, shelves and similar article with plain faces including form work complete all as specified and as directed

M&L for 75 mm thick cement concrete (1:3:6) type C-2 with using 40 mm graded stone aggregates) as in sub base of flooing etc complete all as specified and as directed

Providing and laying 60 mm thick factory made chamfered edge cement concrete paver block of M-35 grade design mix with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc.,of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra complete all as specified and as directed

M&L for providing pre cast cement concrete type B1 (1:2:4) 20mm graded stone aggregate) solid block in kerb stone edging etc (of any spcification) with plain fair faces incl chambers watering throathings etc setting in cement mortar (1:4) with joints to match complete all as specified and as directed

Taking down copper/aluminium point wiring (light, fan, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

Taking down old/unserviceable distribution board by disconnection of electric connection carefully SPN DBs/TPN DBs/ Main Switch including old unserviceable MCCBs/ MCBs, Isolators, etc and making good to disturbed surface complete all as specified and directed.

Taking down carefully copper/aluminium Sub main wiring of any size from surface/concealed /existing conduit of any height and removing materials at site and making good disturbed surfaces of walls, floors roofs etc complete all as specified and directed.

M&L for point wiring for One light point controlled by one way switch 5/6 amps with 1.5 sqmm single core PVC insulated unsheathed FR-LSH cable 1100 volts grade (ISI marked) with multistranded copper conductor with proper colour coding drawn through and including non-metallic rigid 20 mm bore PVC medium grade conduit and conduit accessories (ISI Marked) concealed in wall/fixed to roof, ceiling etc including provision of 1.5 sqmm PVC insulated multistranded unsheathed copper conductor cable FR-LSH (ISI Marked) with proper colour coding as earth continuity conductor connected to common earth dolly, modular sheet steel sunken terminal box of appropriate size suitable for modular switch/ fittings concealed in walls, with modular back plate, top cover fixed flush to wall for housing switches, socket outlets, fan regulators etc duly earthed including cutting chases of existing wall for for conduits and sinking for boxes and making good to the disturbed surface of wall/floor and matching with existing specifications. Connections of cable with MCB's or bus bar shall be done through proper size copper/brass thimbles complete all as specified and directed. Note :- (i) Quoted rate shall be include chase cutting, making good to the disturbed surfaces including plastering and painting to match with the existing colour. (ii) Make of modular box, modular back plate & cover shall be of same make as switch, socket, & fan regulator etc.

All as per Sr' Item No. 172 here-in-before but for One ceiling fan/Exhaut fan point controlled by one way switch 5/6 amps and with ceiling Fan Regulators in case of ceiling fan point complete all as specified and directed.

All as per Sr' Item No. 172 here-in-before but for One socket out let 5/6 amps point on the independent board complete all as specified and directed.

All as per Sr' Item No. 172 here-in-before but for One socket out let 5/6 amps point on the same board complete all as specified and directed.

All as per Sr' Item No. 172 here-in-before but for One bell point controlled by one way switch 5/6 amps complete all as specified and directed.

All as per Sr' Item No. 172 here-in-before but for One light point controlled by two, two way switch 5/6 amps complete all as specified and directed.

All as per Sr' Item No. 172 here-in-before but wiring with 2.5 sq mm single core multistranded FRLSH copper conductor for one socket out let 15/16 amps point on the independent board including 2.5 sqmm PVC insulated multistranded unsheathed FRLSH copper conductor as earth continuity conductor complete all as specified and directed.

S&F of Modular switch, single pole, one way, 6 Amp, 1 Module, 230 volt, ISI marked complete all as specified and directed.

S&F of Modular switch, single pole, Two way, 6 Amp, 1 Module, 230 volt, ISI marked complete all as specified and directed.

S&F of Modular switch, single pole, one way, 16 Amp, 1 Module, 230 volt, ISI marked complete all as specified and directed.

S&F for epoxy powder coated sheet metal enclosure with socket plug top and MCB, single pole and neutral enclosure with a two pin and earth plug and socket complete with one MCB, SPN, 20 Amps, 240 Volts, C Series current carrying capacity 10 kA, incl necessary connection complete all as specified and directed.

S&F of Socket, 6A-2/3 pin combined 2 module 230 Volts,,50Hz, ISI marked complete all as specified and directed.

S&F of Socket, 6A/16A-2/3 pin combined 2 module 230 Volts,,50Hz, ISI marked complete all as specified and directed.

S&F of Modular bell push, one way, 6 Amp, 1 Module, 230 volt, ISI marked complete all as specified and directed.

S&F of Bell Electric Ding dong type suitable for operation on 230 volt 50 HZ A C supply complete all as specified and as directed

S & F lamp holder, insulated body PVC / polycarbonate type, with back plate suitable for batten/angle fittings complete all as specified and directed.

S&F Highly efficient LED Bulbs, 10 W, used as a ready replacement for existing GLS/CFL direct fit lamp,in B-22 cap complete all as specified and directed.

S&F of stepped type (five step) electronic fan regulator, flush type, 120 watt 2 module suitable for 1200/1400 mm sweep energy saving BLDC fans, ISI marked complete all as specified and directed.

S&F in ceiling rose, bakelite, surface type, 220/240 volts, three terminals complete all as specified and directed.

M&L for (Inverter connection) with PVC insulated unsheathed stranded, FRLSH copper conductor cable of size 1.50 Sqmm to be drawn through existing PVC medium grade surface PVC conduit/casing caping/ concealed point incuding all necessary wall cutting and making good disturbed surface and provision of one outlet with 15 Amp modular socket for connection of inverter complete all as directed and specified. Note : Cutting chases and Making good to match with the adjoining surface and provion of one outlet with 15 Amp modular socket for connection of inverter shall be included in the unit rate.

Material and labour for concealed sub-main wiring alongwith earth wire of size of 2 x 4.0 sq. mm + 1 x 4.0 sq. mm earth wire, ISI marked, FRLSH, PVC insulated, multi stranded, copper conductor, single core cable drawn through and including PVC rigid conduit (medium grade) of of size not less than 20 mm with all fittings and accessories ISI marked including cutting chases for conduits & making good to walls, floors etc complete all as specified and directed. NOTE : Two runs of 4 sqmm conductor for main and one run of 4 sqmm conductor as earth wire with proper colour coding including one run run of PVC conduit shall be measured as one unit length. Connections of cables with MCBs or bus bar shall be done through appropriate size brass/ copper thimbles.

S&F for LED tube light batten box type with decorative end caps including one single LED tube 1x 18/20 watt T8 lamps type complete with both end bi-pin holder and all accessories internally pre wired and fixed to wall/ceiling with warranty 5 years from date of installation complete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting complete all as specified and as directed.

S&F for sheet metal enclosure MCB DB SPN 8 way with 200 Amps rated bus bar 240 volts double door having ingress protectoin level IP-54 and impact resistance level IK-09 with metal with magnetic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed.

S&F for MCB Single pole and neutral rated capacity 32 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

S&F for MCB Single pole rated capacity 6 to 32 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

S&F for Decorative wall light fixture made up of polycarbonate suitable for 10 Watt LED retrofit of type B-22 base, IP66 grade, with and including 10 watt LED (or nearest next higher wattage) lamp and connecting up with and including PVC insulated suitable size copper conductor to terminal block of light fitting including necessary taking down the old unserviceable fitting complete all as specified and directed.

S&F for IP 20, class I, LED light 1X18 W (or nearest next higher wattage) (4 feet), 5700K, wall/ surface mounted, integrated type with aluminium housing and decorative and caps with integrated high efficiency electronic driver and surge suppressor of 2KV or more, luminaire efficiency > 95 lumens/watt, power factor > 0.90, operating range - 140 to 270 V, 50 Hz fixed with 02 Nos of PVC round/ square blocks, screws etc with all accessories internally prewired and connecting up complete all as specified and directed.

S&F for IP 20, Class I, LED tube light fitting 1 x 10 W, (or nearest next higher wattage) 5700 K, wall /Surface mounted with aluminium housing 2 feet long, integrated type, with high efficiency diffuser, integrated high efficiency electronic driver & surge suppressor of 2 KV or more, luminaire efficacy > 100 lumens/Watt, power factor >/ 0.90, operating range – 140 to 270 V, 50 Hz fixed with 02 Nos of PVC round/square blocks, screws etc complete including 01 No 10 W LED lamp with all accessories internally prewired and including connecting up with and including twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed.

S&F for energy saving new generation Bulk head luminaire suitable for 10 Watt LED (or nearest next higher wattage) light IP66 grade, luminaire efficiency not less than 120 lumens/watts with and including 10 watt LED (or nearest next higher wattage) lamp and connecting up with and including PVC insulated 3 core of size 0.75 Sqmm copper conductor from ceiling rose to terminal block of light fitting complete all as specified and directed.

S&F for Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 65 for security light fitting luminaire with high power LEDs as light source and electronic driver, LDR sensor for automatic switch ON/ OFF of capacity 25 watts with pre wired and necessary mounting arrangements and provision of 1.5 sq mm three core copper conductor cable multi stranded from ceiling rose to light fitting including necessary dia GI pipe medium grade bracket 1.0 mtr long bend to required shape with clamps, nut, bolts complete all as directed.

Taking down ceiling fan of any sweep, keeping with safe custody and deposited to MES store yard complete all as specified and as directed.

S&F for BLDC ceiling fans 1200 mm sweep 230 volts 50 Hz, 5 star BEE rated with brushless direct current motor (BLDC), energy saving, 100 % copper wound motor complete with anti corrosive alluminium blades of minimum thickness 1.10 mm, powder coated finished, double ball bearing maxmium wattage 26 to 32 watts, Min air delivery 220 (+/- 2%) CFM with service value above 6.50, ISI marked complete all as specified and as directed.

S&F for energy efficient exhaust fan of 300 mm sweep made of metal body Ventil Air -DS type complete with louver with bolts nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection and making suitable size of hole to existing brick wall for fan base complete all as specified and directed. Note : Cost of suitable opening in wall for fixing exhaust fan is deemed to be included in overall rate quoted.

S&F for energy efficient exhaust fan of 250 mm sweep made of metal body Ventil Air -DS type complete with louver with bolts nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection and making suitable size of hole to existing brick wall for fan base complete all as specified and directed. Note : Cost of suitable opening in wall for fixing exhaust fan is deemed to be included in overall rate quoted.

Supply, installation and testing of electric water heater storage vertical type, 5 star rated, 25 ltr capacity comprising of high wattage heating element for instant heating, extra Mild steel with Glass lined coated inner tank, rust & shock proof ABS outer body, non-ferrous pressure plate with & including provn of 04 Nos grouting bolts suitably flushed to wall or any other surface including PVC connection pipe hot and cold type, 15 mm dia, 450 mm long with brass adopter & washer on both sides and connection with 3 core PVC insulated, sheathed, stranded copper conductor cable/ flexible chord and one no 15 amps 3 pin plug top complete all as specified and as directed.

BLANK

BLANK

BLANK

BLANK

M&L for earthing complete with galvanised steel earth plate electrode of size 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below ground level, connected to galvanized earth lead of 25x4 mm by means of bolts nuts check nuts & washers of galvanized iron or steel , procteded by GI pipe 40 mm bore( light grade) and watering pipe 20 mm bore GI pipe (medium grade) and chamber and coping shall be in PCC 1:3:6 type C1 using 20mm graded stone agg. 50 mm thick cover of RCC 1:2:4 type B1 using 20 mm graded stone agg. reinforced with 8 mm dia MS tor bar @ 80 mm c/c both ways including excvation and earth work and removal of surplus soil complete all as shown in electrical plate no 3 of SSR PT 1, 2009 with charcoal dust and salt complete and earth lead connected to earthing test point (up to main switches, DBs complete all as specified and directed. Note: GI earth strip 25 mm X 4 mm protection pipe and 40 mm dia light grade Gi pipe upto 7.5 mtr from earth plate are deemed to be included in the rate quoted.

M/S. S.K. TEKRIWAL (BID ID -3427684)

M/S R. K. INDUSTRIES (BID ID -3420894)

M.P. SITANI AND SONS (BID ID -3421713)

M/S JYOTI SHARMA AND SONS (BID ID -3421583)

Brahmaputra Commerce and Trade (BID ID -3420884)

B D RAIZADA PROJCTS PVT LTD (BID ID -3421518)

M/s Singh enterprises (BID ID -3420490)