REPAIR TO PLASTER FLOORING AND CERTAIN MISC WORKS IN BLDGS VIZ SINGLE SAILORS BLOCK, JOC NOORBHOY MET SECTION BSQ AGNIBAHU AND CERTAIN OTHER BLDGS AT INS ANGRE UNDER AGE BR II UNDER GE NW KUNJALI

Amount

Taking down cement or cement lime plaster, any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc including all necessary scaffolding as required and rubbishing off the premises etc complete all as specified and directed by Engineer-in-Charge.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles and disposing off complete all as specified and directed by Engineer-in-Charge.

Material and Labour Plastering 15mm thick in CM 1:6 on brick surfaces, finished with Neeru finish on walls complete all as specified and directed by Engineer-in-Charge.

Material & labour rendering 20mm thick in two coats(15mm inner coat 5mm finishingcoat) on brick work or concrete surfaces in cement mortar 1:4 finished even and fair including mixing integral water proofing compound in the proportion as mentioned in manufacturer's instructions including necessary scaffolding for high rise bldgs etc all as specified and directed. (Water proofing compound to be measured and paid for separately).

Material and Labour Plastering 5mm thick in CM 1:3 on concete surfaces as in ceiling finished even & smooth without using extra cement in ceiling complete all as specified and directed by Engineer-in-Charge.

Supply only integral water proofing compound complete all as specified and directed by Engineer-in-Charge.

Material and Labour brick work with sub class B bricks straight or curved on plan exceeding 6 m mean radius built in CM 1:6 complete all as specified and directed by Engineer-in-Charge.

Material and Labour for brick work with sub class 'B' bricks straight or curved on plans to any radius in half brick thick walls built in cm (1:4) complete all as specified and directed by Engineer-in-Charge.

Preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper over a coat of of primer complete all as specified and directed by Engineer-in-Charge.

Material and Labour for preparation of newly plastered surfaces of ceiling and applying two coat of oil emulsion distemper over a coat of primer complete all as specified and directed by Engineer-in-Charge.

Material and Labour for preparation of old painted steel surfaces of any description, over 10 cm in width or girth not otherwise described and applying one coat of synthetic enamel paint with necessary scafolding for high rise bldgs etc complete all as specified and directed by Engineer-in-Charge.

Material and Labour for preparation of newly steel surfaces of any description over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed by Engineer-in-Charge.

Material and labour Complete removal of existing treatment on wall surfaces by scrapping, washing & rubbing down with water and applying two coats of oil bound distemper over a coat Chalk whiting, on plastered surfaces complete all as specified and directed by Engineer-in-Charge.

Material and Labour for preparation of old decorated surfaces of wall and applying one coat of oil emulsion distemper complete all as specified and directed by Engineer-in-Charge.

Material and Labour for applying 1 to 2 mm thick wall care putty (JK/Birla) for making the surface even & smooth all as specified and directed by the Engineer-in-Charge.

Material and Labour for preparation of old decorated surfaces of ceiling and applying one coat of oil emulsion distemper complete all as specified and directed by Engineer-in-Charge.

Complete removal of existing treatment on wall surfaces by scrapping, washing & rubbing down with water etc and applying two coats of plastic paint over a coat of primer complete all as specified and directed by Engineer-in-Charge.

Complete removal of existing treatment on wall surfaces by scrapping, washing & rubbing down with water etc and applying one coat of plastic paint over a coat of primer complete all as specified and directed by Engineer-in-Charge.

Material and Labour for preparation of newly plastered surfaces of wall, soffits, facia roof and applying two coats of weather proof acrylic based paint (100% acrylic) over one coat of cement based primer with necesssary scaffolding for high rise blds etc complete all as specified and directed by Engineer-in-Charge.

Material and Labour Complete removal of existing treatment of old decorated surfaces of walls soffits, facia roof and applying two coat of weather proof acrylic based paint (100% acrylic) over one coat of cement base primer with necessary scafolding for high rise bldgs. etc complete all as specified and directed by Engineer-in-Charge.

Material and Labour preparation of old decorated surfaces of walls, soffits, roof facia and applying one coat of weather proof acrylic based paint (100% acrylic) with necessary scafolding for high rise bldgs etc complete all as specified and directed by Engineer-in-Charge.

Material and Labour for preparation of newly wooden surfaes of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer incl preparation of surfaces complete all as specified and directed by Engineer-in-Charge.

Material and Labour for preparation of old painted wooden surfaes of any description over 10cm width or girth and applying one coat of synthetic enamel paint including external window with necessary scafolding for high rise bldgs complete all as specified and directed by Engineer-in-Charge.

Taking down chowkats or frames but n exc 1.5 sqm each but with shutters (without taking off shutters from the frame) complete all as specified and directed by Engineer-in-Charge.

Taking down chowkats or frames exc 1.5 sqm but n exc 4 sqm each but with shutters (without taking off shutters from the frame) complete all as specified and directed by Engineer-in-Charge.

Taking down shutters of any description exc 1 sqm and n exc 2 sq.m each complete all as specified and directed by Engineer-in-Charge.

Taking down shutters of any description n.exc 1.00 Sqm each complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 2nd class hard wood (sal) plain, solid, straight chawkhats and frames, wrought, framed, rebated on the solid rounded or chamfered, put together with glue pinned at joints all as complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 35mm thick factory made 2nd class HW rail & stile plain framed , panelled shutter ( two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 ( Part I), kiln seasoned and chemically pressure treated complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing factory made, 2nd class hard wood 35 mm thick, glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass/gauze etc complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 30mm thick 2nd class hardwood glazed and skeleton shutters open rebated and prepared to receive glass, gauze, etc. divided in to squares,with plain, chamfered or rounded , mitred and rebated sash bars,any numbers ; edges of framing plain, chamfered or rounded , fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part I, Section 8 clause 8.24 (b) ; supplied and fitted to chowkhats of Second class hard wood complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 40mm thick flush shutters, solid core construction, with block board core and ply wood face panels, commercial type on both side complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repair powder coated aluminium (minimum 25 micron thickness of coating) of various section as required for doors, window & partion/Ventilator etc including fixing and making the frames hinges to receive glass/wire gauge etc. Complete incl all fittings like rubber beading, clips locking arrangement, handle, tower bolt for shutter, sealant etc all as specified and as directed by Engr- in- charge complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repair aluminium grill with and including suitable aluminium anodised frame F/H section as required manufactured by M/S Decogrill as per design No DG- 102, 7.5 mm thick all as specified and as directed by Engr- in- charge.

Supply and Fixing stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel stapple etc complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel stapple etc complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs 18/19 mm thcik prelaminated partical board exterior grade prelaminated one side with lamination and other side balancing white lamination fixed with screw to frame work cupboard etc including 6 mm thick teak wood beading all around complete all as specified and directed by Engineer-in-Charge.

All as per item No 38 above but 9 mm thick pre-laminated partical board fixed in repairs.

Supply and Fixing 12mm thick prelaminated medium density fibre board,interior grade, prelaminated both side with decorative choice lamination fixed with screws to aluminium frame work complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 300 mm long aluminium alloy, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing for aluminium anodized barrel tower bolts 150 mm of extruded section and fixed complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing for aluminium anodized barrel tower bolts 200 mm of extruded section and fixed complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 150 mm size aluminium alloy handles, febricated type extruded section, ISI marked complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing butt hinges 100 mm mild steel hinges medium weight and fixed complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing butt hinges 100 mm stainless steel hinges medium weight and fixed complete all as specified and directed by Engineer-in-Charge

Supply and Fixing butt hinges 75 mm mild steel hinges medium weight and fixed complete all as specified and directed by Engineer-in-Charge

Material and Labour for MS flat for hold fast. Conforming to Fe-290-0 or Fe-165 complete all as specified and directed by Engineer-in-Charge

Supply and Fixing in repairs 125 mm long floor door stopper of aluminium door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 12mm thick plywood ,grade bwp type BB, fixed with screws to timber frame as in paneling/partition complete all as specified and directed by Engineer-in-Charge.

Material and Labour 0.9mm thick decorative texture finish laminate type 1 , of surface finish colour and pattern as approved fixed with adhesive as per makers instruction complete all as specified and directed by Engineer-in-Charge.

Material and Labour for gently cleaning the surface of the stone masonary/ stone chips and piers with specialized eater misting techniques employing air water jet using a fine nozzle sprinkling system calibrated to spray a fine mist along the stone surface without over wetting followed up by gentle brushing with soft nylon brushes as specified and milded. Gentle surface cleaning may include using water misting and PH balanced surfactants as specified for indicated areas to remove surface dirt grit surface accretions, lime wash painting etc by means of water misiting and PH balanced surfactants and cleaning complete all as specified and as directed Note : Quoted rate shall be inclusive of removing vegetation on wall surfaces.

Material and Labour for applying 4mm thick finished texture mortar in CM 1:2 (Mix one part of white cement & two parts of Dholpuri clear quarts powder of 1 to 2 mm grading) incl texture finish shall be achieved with the help of hand driven machine incld preparation of old painted surface & newly plastered surfaces and making plain surface of stone masonary pattern incld irrection & dismantling of scaffolding to carrying out works upto triple stories Bldg complete all as per manufactures instructions and directed by Engineer-in-Charge

Supply and Fixing in repairs fancy type drapery rods, powder coated aluminium of 20-25mm size with fixing brackets, Knobs rollers etc.all as specified and directed by Engineer-in-Charge

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards/slabs/blankets any thickness including cover fillets etc complete all as specified and directed by Engineer-in-Charge

Supply and Fixing 5mm thick PVC sheet fillet of width 35 mm for wall paneling inclusive of fixing on to wall vertically with screws and C/C distance 30 CM to make PVC frame as per specification and drawing complete all as specified and directed by Engineer-in-Charge

Supply and Fixing PVC wall /ceiling paneling consisting of 5 mm thick plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as specified and directed by Engineer-in-Charge

Material and Labour for false ceiling made out of 600x600x 4 to 6 mm thick ceiliing board / tiles deep panel suspensor system made out of powder coated GI sheet main tee of size 23.50x40x0.63mm and cross tee of size 23.50x23.50x0.63mm and angle size 19x19x0.63mm including 3mm GI wire for suspending bolts necessary washers nut/clits/pin hook etc. for securing frame work to ceiling to the snap grid all as directed by Engr-in-charge including provn of necessary holes / cuttings for providing light/fan as required including making necessary recesses / projected pattern complete all as specified and directed by Engineer-in-Charge

Material and Labour for POP false ceiling using 600X900x12 mm thick plaster of paris with gypsum binder sheet decorative type and necessary provision for concealed type light fittings, fixed on 22 gauge GI channel grid work, main joist of size 50x25 mm spaced at 750 mm centre, secondary joist of size 75X20 mm fixed to main joists spaced at 900mm, suspended to roof members using 25x25x2 mm GI angles and fasteners @ 1.2 M C/C, including dismantling old un serviceable flase ceiling, complete all as specified and directed.

Supply and Fixing roller/venetian blinds vertical/horizontal type made out of standard cloth of approved texture with necessary accessories etccomplete all as specified and directed.

Supply and Fixing in repairs Wall paper of fibrious material, nonwoven Vinyl free, making them fixed to wall with dry strips or with approved adhesive. Deign & pattern as approved by GE.

Supply and Fixing Solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers complete all as specified and directed by Engineer-in-Charge

Demolition of cement concrete (unreinforced) in ground floor and in paving not exceeding 15 cm thickness (below or above ground level) complete all as specified and directed by Engineer-in-Charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed by Engineer-in-Charge..

Material and Labour for rolled mild steel section as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors ; fixed with angle cleats or other connecting plates conforming to grade Fe 290 (Gde-E-165) complete all as specified and directed by Engineer-in-Charge.

Dismantling plain or corrugated steel/AC roof sheets any gauge, thickness, including Nainital or similar pattern roof covering complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, chajjas, fixed with self tapping screws as specified.

Supply and Fixing pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, chajjas, valley gutter, ridge and fixed with crumple joint etc fixed with self tapping screws as specified.

Supply and Fixing for 1.50mm thick plain , galvanised mild steel sheeting in ridges , valley gutters,drip and other suitable arrangements over MS brackets Trapezoidal shape of required profile with desired slope etc complete all as specified and directed by Engr-in charge .

Material and Labour for 100 mm thick cement concrete 1:4:8 type D-2 (40 mm graded stone agg) as in sub base complete all as specified and directed by Engineer-in-Charge

Material and Labour for machine pressed precast concrete inter locking paver block any shape and size confirming to IS-15658-2006 of 60mm thickness M-35 Grade, glossy finished of approved colour laid over and including 25 mm thick fine sand cushion to a line and slope etc and joined complete including spreading screened river sand over surface for filling the joints with rising surface vibrator etc complete all as specified and directed by Engineer-in-Charge.

Providing plain cement concrete type B-1, 1:2:4 (using 20 mm graded stone agg) as in lintels upto 1.5 M clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railing upto 60 cm in height, copings, kneelers, apex stones, bed plates, roof kerbs, water troughs and the like including weathering slightly rounded or chamfered angles and throating complete all as specified and directed by Engineer-in-Charge.

Dismantling stone slab and tiles of of any description or thickness laid bedded and pointed in any mortar in floors, aprons etc all as specified and directed.

Material and Labour 20 mm thick Granite (of any type) work (table rubbed and polished) as in steps, jambs, pillars, window- cills,cooking platforms, working table and like over 20 mm thick screed bed or bedding layer in cement mortar (1:4), including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed by Engineer-in-Charge

Material and Labour for machine cut cudappa stone slab 20-25 mm thick fixed independently and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

Material and Labour for machine cut kota stone slab flooring 18 to 20 mm thick as in steps, landings, floors etc laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing,mirror polishing incl making 02 Nos grooves in steps over & incl 20 mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

Material and Labour for machine cut kota stone slab 18 to 20 mm thick as in skirting/vertical surfaces jointed and pointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, polishing and 15 mm thick backing coat in cement mortar 1:4 complete all as specified and directed.

Rounding to edges of stone slabs on edge, such as in steps, cooking platform and making grooves for lining and other similar work complete all as specified and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing), removing serviceable tiles to store and disposing the rubbish to the out side of MD land complete all as specified and directed by Engineer-in-Charge

Material and Labour in repairs Cast iron nahani trap with grating including jointing to waste pipe run lead 100 mm complete all as specified and directed by Engineer-in-Charge

Taking down PVC wastage and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc complete all as specified and directed by EIC

Supply and Fixing 160mm dia bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls with ms clamps complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 160mm dia bore PVC (SWR) bends any radius complete all as specified and directed by Engineer-in-Charge

Supply and Fixing 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed by Engineer-in-Charge

Supply and Fixing 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed by Engineer-in-Charge

Supply and Fixing 110 mm bore PVC (SWR) bends any radius complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 75 mmbore PVC (SWR) bends any radius complete all as specified and directed by Engineer-in-Charge.

Taking up or down existing GI water tubing complete with all fittings of 15 mm bore complete all as specified and directed by Engineer-in-Charge

Taking up or down existing GI water tubing complete with all fittings of 20 mm bore complete all as specified and directed by Engineer-in-Charge

Supply and Fixing GI tubing medium grade with all fittings like Tee, bend, elbow etc, 15 mm bore fixed to walls or ceilings with saddles/spacers complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing GI tubing medium grade with all fittings like Tee, bend, elbow etc, 20 mm bore fixed to walls or ceilings with saddles/spacers complete all as specified and directed by Engineer-in-Charge.

Material and Labour Apply evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sqm including cleaning surface complete all as specified and directed by Engineer-in-Charge.

Material and Labour for Cement concrete 1:7:12 type F2 (40mm graded aggregate) complete all as specified and directed by Engineer-in-Charge.

M/L PCC 1:3:6 type C-2, 100 mm thick as in sub base for sunken slab/floor complete all as specified mixed with WPC 3% by weight of cement, finished even and smooth without using extra cement. (WPC shall be measured and paid separately).

Material and Labour for 20 mm thick cement screed in cement mortar 1:3 mixed with liquid water proofing compound FOSROC's complast 421 IC @ 130 ml per bag of cement including a bonding coat of FOSROC's Nito bond AR cement slurry for sunken slab/floor complete all as specified ( liquid water proofing Compound are measure separately ).

Supply and Fixing in repairs Vitreous China wash down water closet pan , white (excluding fixing bolts, flushing cistern and flush pipe) fixed in repairs complete all as specified and directed by Engineer-in-Charge

Supply and Fixing in repairs, Plastic water closet seat, black or white closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed by Engineer-in-Charge

Supply and Fixing in repairs water closet squatting pan (Orissa pattern) 580x440mm, white with integral foot rests including connecting to trap and to flushing pipe antisyphonage pipe including making good to floor (excluding flushing cistern and flush pipe) complete all as specified and directed by Engineer-in-Charge.

Supply and fix only cast iron 'P' trap 100mm dia complete all as specified and directed by Engineer-in-Charge

Supply and Fixing in repairs fancy type CP Pillar taps 15 mm dia, cast copper alloy , with capstan heads, screwed down high pressure ,with long screwed shanks and fly-nuts , screwed for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge

Supply and Fixing in repairs fancy type bib taps, chromium plated cast copper alloy 15mm bore with crutch or butter fly handle, screwed down, & fixed complete all as specified and directed by Engineer-in-Charge

Supply and Fixing in repairs fancy type angle valve chromium plated cast copper alloy 15mm bore with crutch or butter fly handle complete all as specified and directed by Engineer-in-Charge

Supply and Fixing in repair wash hand basin vitreous china white (flat back) of size 550x400mm including bracket 15mm dia 32mm dia waste coupling and 32mm dia PVC waste pipe 90cm long etc. complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing PVC connections 15 mm size with PTMT nuts of length 600mm complete all as specified and directed by Engineer-in-Charge

S/F in repairs PVC valveless syphonic action type ,flushing cistern Low level white, with inlet ball valve ,float and handle 10 Ltr capacity including brackets complete all as specified and directed by Engineer-in-Charge

Supply and Fixing in repairs Flush pipe of Polyethylene of low or high density or PVC 32 mm dia. for low level cistern complete all as specified and directed by Engineer-in-Charge complete all as specified and directed by Engineer-in-Charge

Supply and Fixing in repairs Soap dish any type fixed to plugs with chromium plated brass screws complete all as specified and directed by Engineer-in-Charge

Supply and Fixing vitreous china urinals, bowl type , flat back, size 465X355X265mm, white, with grating and union for discharge pipe, complete including providing and fixing plugs, bedding urinal against wall in CM 1: 2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement , fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe.(Exclusive of fixing supply pipe to flushing cistern , trap and waste pipe), fixed in repairs complete all as specified and directed by Engineer-in-Charge

Dismantling water tank of capacity exc. 250 Ltrs but n.exc. 500 ltrs complete all as specified and directed by Engineer-in-Charge

Dismantling water tank of capacity exc. 500 Ltrs but n.exc. 1000 ltrs complete all as specified and directed by Engineer-in-Charge

Dismantling water tank of capacity exc. 1000 Ltrs but n.exc. 2000 ltrs complete all as specified and directed by Engineer-in-Charge

Supply and Fixing rotational moulded polythylene water storage loft tank tank of 300 ltr capacity hoisted including 20 mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for inron pipe and fixed (minimum weight 210 grms ) all as specified in SSR Part I complete all as specified and directed by Engineer-in-Charge

Supply and Fixing rotational moulded polythylene water storage tank of 1000 ltr capacity (Cylindrical vertical with closed top) hoisted including 20 mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for inron pipe and fixed (minimum weight 210 grms ) all as specified in SSR Part I. complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing rotational moulded polythylene water storage tank of 2000 ltr capacity (Cylindrical vertical with closed top) hoisted including 20 mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for inron pipe and fixed (minimum weight 210 grms ) all as specified in SSR Part I. complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs 20 mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 210 grms) complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs PVC modular section 20mm thick as in profile including 'C' channels, aluminium all around the profile complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs health faucet ABS Body with 8 mm dia 1 mtr flexible tube and wall hook complete all as specified and directed by Engineer-in-Charge

Supply and Fixing in repairs Corner glass shelf with brackets complete all as specified and directed by Engineer-in-Charge

Supply and Fixing in repairs aluminium anodised tubular towel rail 20mm dia D type 60 cm long between flanges complete all as specified and directed by Engineer-in-Charge

Supply and Fixing in repairs door closer hydraulically regulated, designation No 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 Kg and fixed complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 4mm thick bakelite sheet with decoratie choice laminated on both side complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 3 mm thick aluminium composite panel cladding plain of approved colour/shade to beam/column/slab incircular/rectangular shape inbcluding cutting, notching, bending to shape as required jointing with silicon gel of approved colour & aluminum tubular hallow section 25 x 25 mm not exceeding 900 mm C/C on exceeding column/beam/slab to hold APC cladding etc (Note : colour/pattern of ACP sheet shall be given by GE).

Supply and Fixing under counter wash hand basin incl chromium plated brass waste coupling and PVC waste pipe complete all as directed Make - Jaquar CAT PART NO- CNS-WHT-705.

Supply and Fixing single piece WC with UF foft close seat cover, hinges, fixing accessories set and accessories set, cistern fittings incl trap/connecting piece cocomplete all as specified and directed by Engineer-in-Charge.

Removing of bldg materials exc 5 KM but not exc15.00 KM and depositing where complete all as specified and directed by Engineer-in-Charge

Supply and Fixing double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium ally sheet foundation box, main body with stainless steel cover, governing pivot made of bras, other parts made of mild steel heavy duty and fixed complete all as specified and directed by Engineer-in-Charge.

RAMESH ENTERPRISES

Satyanarayan Trading Co.