SPECIAL REPAIR FOR AUTOMATION OF HIGH MAST LIGHT FITTINGS WITH LED LIGHT FITTINGS INCL CANTROL PANELS AT VARIOUS LOCATION OF MCTE AREA UNDER GE(MCTE) MHOW

Amount

Excavation in trenches not exc. 1.5 Mtr wide and not exc 1.5 Mtr deep in hard/dense soil and getting out complete all as specified and as directed.

Returning filling soil in trenches including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick in any type of soil complete all as specified and as directed.

Removing surplus excavated soil (material) to a distance not exc 50m and depositing where directed at a level not exc 1.50m above the starting point complete all as specified and as directed.

M&L for filling approved fine river sand in trenches as cable cushion to the full width of excavated trench, under and over cable complete all as specified and as directed. (Note : Punned thickness of sand shall be measured)

M&L for bricks slightly over burnt (kiln burnt) , modular bricks, best quality, locally available, laid flat, dry, laid in trenches along the length of cable transvarsally with width equal to length of brick for cable protection all as specified and as directed.

S&F in replacement of LED flood light 200 Watt die cast aluminium housing with separate LED and driver compartment, Rectangular LED Flood Light with innovative thermal management and available in multiple optics and equipped with IP66 protection, in built electonic LED driver all as specified and directed. Make : Crompton Cat Part No LFLN-200-CDL/60 or equivalent in Philips/ Bajaj.

All as per ser item No 6.00 above but LED flood light of 150 watt. Make : Crompton Cat Part No LFLN-150-CDL/60 or equivalent in Philips/ Bajaj.

All as per ser item No 6.00 above but LED flood light 120 watt. Make : Crompton Cat Part No LFLN-120-CDL/60 or equivalent in Philips/ Bajaj.

Supply and fixing in replacement of LED street Light fittings lumanaries 60 watt LED with lens , pressur die cast epoxy powder coated aluminium housing with efficient designed heat shrink with heat resisitent toughned glass with fram fixed with SS Screws suitable for fixing in existing poles, with protection IP-66, power factor not less than 0.95, surge 5KV, total harmonic distortion THD is < 10% lumen not less than 100 lumen/watts complete, including dismantling of old one fittings, all as specified and directed by Engr-in-charge. Make :- Crompton Cat Part No LSTP-60-CDL or equivalent in Bajaj/ GE.

Sppply & Laying XLPE insulated, armoured, electric cable 16 Sqmm 4 Core with aluminium conductor, 1100 volts grade, laid in trenches, fixed on poles / walls or passing through pipes including provision of necessary lugs and glands & making necessary connection complete all as specified and as directed.

Sppply & Laying in replacement of XLPE insulated, armoured, electric cable 1.5 Sqmm 12 core with copper conductor, flexible type 1100 volts grade, laid in high mast light vertically including provision of necessary lugs and glands & making necessary connection complete all as specified and as directed.

Supply and fixing in replacement of three pole power contactor 65 Amps Integrated auxiliary contacts 2 NO + 2 NC screw terminals control voltage 24 V all as specified and as directed. Make : Legrand Cat Part No : 416160 or equivalent in ABB/ L&T.

Supply and fixing in replacement of Analog Time Switch with battery back up 3P Module, 24 hours programme ,Programmable every 15 min, back up of 100 hours current cap 16 Amps with 1 changeover (1 CO) all as specified and as directed.

S&F in replacement of Automatic Street Light control switch for three phase 32 Amps, using Infrared Analog Time Switches for automatic switching of street lights. Nature Switch operation should be based on Natural Light Lux level. Required illuminance level for switching ON is ≤ 30 Lux and for switching OFF ≥ 10 Lux. The Analog Time Switches should also have part night operation facility of min. 4 hrs to max. 12 hrs (Time setting 2 to 4 times).The Analog Time Switches along with 03 Nos contactors each of 32 to 40 Amps capacity, Incoming MCBs and Outgoing MCBs of 32-40 Amps (03 Nos) and auto manual operation (Analog Time Switches by Pass), size of circuit wiring should be multistranded FRLS min size of 10 Sqmm should be enclosed in a pole/wall mounted enclosure made of rust proof, Electric Shock Proof, Termite proof and FR grade SMC Junction box conforming to IP54 complete all as specified and as directed.

Supply and fixing in replacement of MCB, four Pole 63 Amps, D Series, rapturing capacity 10 KA, 415 volts AC.

Material and labour for earthing complete with steel earth plate eletrode 60cm x 60cm x6mm thick buried dirctly in ground vertically (earth pit not less than 2.25 mtr below ground level) with top edge of plat not less than 1.5 mtr below ground level connected to GI strip 32x6mm by means of bolts. nuts,check nuts and washers etc including protection pipe 15mm dia up to 7.5m length , provision the earth lead to earth connection in ther main distribution box with lugs and GI nuts,bolts, earthing shall be done all as per shown electrical plate No 5 of SSR part 1 Including neccessary excavation in disintergratedand hard soil and 20mm dia GI pipe with funel for watering PCC earth chamber 100mm thick precast RCC cover with suitable precast RCC frame and earth test point and testing in presence of Engr -in -Charge

m/s bansal construction

Ms Kailash Chandra Babulal

Mighty Steel Sales Crop

Manu Enterprises

Auto Traders

AGARWAL BUILDERS

SAHYOG ELECTRIC

M/S AUTOMATION AND SWITCHGEAR CONTROL