ADDN/ALTN TO ROOF SHEET INCL ROOF TREATMENT IN BLDG NO P-451 , BLDG NO P-450, PROVN OF HARDSTANDING,OVERHEAD SHELTER OF ENCLOSING OF VARANDAH BY ALUMINIUM, GLASS SIZE IN BLDG NO P-452, PARTITION WALL AT BLDG NO P-02 UNDER AGE B/R III OF GE(S) JAIPUR

Amount

Job No:- 09/MIN/61SA/Q3W/21-22 Demolition of PCC in roof covering, kerbs, roof kerbs, benching, coved fillets etc including old decayed water proofing treatment of any type all as directed by Engineer-in-charge complete.

M&L for surface preparation by removal of all loose particle to ensure clean, smooth and dry surface and laying 25mm thick PCC type B-0, (1:2:4) using 12.5mm graded stone aggregate finished even & smooth without using extra cement to cover negative slope into prop with WPC @ 3% weight of cement complete.

The surface shall be painted with one coat of polymeric primer @ 0.30 Kg per sqm, conforming to IS : 3384. A layer of APP based polymeric membrane, 3 mm thick (min), weighing not less than 3.0 Kg/m2 reinforced with polyster non woven fabric ( weighing not less than 150 gms/ Sqm). Application of polymeric membrane shall be by torch application all as per manufacturer instructions. and finally applying one coat of bitumen @ 1.2 kg/sqm on APP membrane before application of aluminium paint complete.

PCC 1:2:4 mix type B-o(using 12.5mm graded aggregates) as in roof kerbs rounded or chambered on edge complete.

M&L for one coats of aluminium paint over APP Membrane complete all as specified and as directed.

Excavation in post holes (or similar holes) each n exc 0.5 cu. m, getting out & removing surplus soil to a distance n exc 50m in soft/loose soil complete. Job No :- 09/MIN/61SA/Q3W/2021-22 - 4 Job No :- 10/REV/61SA/Q3W/2021-22 - 8

PCC 1:3:6 type C-2 (using 40 mm graded stone agg) in foundation filling and mass concrete complete. Job No :- 09/MIN/61SA/Q3W/2021-22 - 0.5 Job No :- 10/REV/61SA/Q3W/2021-22 - 4.5

M&L for rolled miled steel in Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lenghts i.e. within 20mm of the length indicated)conforming GDE Fe 410-S complete.

M&L for Pre-painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering, fixed with L-type of J-type hook bolts and washers in roofs etc . Job No :- 09/MIN/61SA/Q3W/2021-22 - 50 Job No :- 10/REV/61SA/Q3W/2021-22 - 132

Preparation of new or previously untreated steel surfcaes of any description, over 10cm width or girth, not otherwise described and applying two coats of synthetic enamal paint over a coat of red oxide primer complete. Job No :- 09/MIN/61SA/Q3W/2021-22 - 20 Job No :- 10/REV/61SA/Q3W/2021-22 - 30

S&F 2mm thick fibre glass reinforced treatment corrugated sheeting with two corrugation side lap fixed with L- Type or J type oe crushed bolts including bitumin washers etc, as in roof walls etc.all as specified and as directed. Job No :- 09/MIN/61SA/Q3W/2021-22 - 20 Job No :- 09/REV/61SA/Q3W/2021-22 - 48

M&L 75mm thick PCC 1:4:8 mix type D-2 (using 40mm graded Stone aggregate) as in Sub base to floor all as specified complete.

M&L for chequered cement concrete tiles 300x300x22mm thick set jointed and pointed in neat cement slurry with grey cement and pigments laid over and including 15mm thick screed bed in CM(1:4) all as specified and directed by Engineer in Charge. Job No :- 09/MIN/61SA/Q3W/2021-22 - 9 Job No :- 09/REV/61SA/Q3W/2021-22 - 45

Job No:- 10/REV/61SA/Q3W/21-22 S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted & fixed in position all as specified in SSR Part I 500 Ltrs Capacity including Dismantling water tanks & removing to store

S&F Ball brass valves 20mm bore, high pressure, with polythene float & flynut complete, screwed for iron pipe or brass ferrule and fixed in repair

S&F for new galvanised steel water tubing medium grade with all fittings and fixed complete to walls and ceilings or laid in floors including taking down complete of following sizes :-

(a) 15 mm bore

(b) 20 mm bore

(c) 25 mm bore

Taking down cement plaster including raking out joints, hacking for key scrubbing down with water etc built in CM

M&L rendering 15 mm thick in CM(1:6) on brick walls or concrete surface, surface finished even and smooth without using extra cement complete all as specified.

M&L Rendering 10mm thick on fair faces of brick work or concrete surfaces in CM (1:3) in ceiling

Providing and fixing 28mm thick factory made PVC Supreme Door Shutter consisting of frame made out of m.S. tubes of 19 gauge thickness nd size of 40mmx20mm for stiles, top and bottom rails having a coat of steel primers of approved make and manufacture. M.S. Frame covered with 4mm thick heat moulded Prelam PVC 'C' Channel of size 28mm thickness,75mm width out of which 60mm shall be flat and 15mm shall be tapered in 45 degree angle on either sides forming stiles, top and bottom rail and 100mm wide Prelam PVC sheet out of which 100mm shall be be flat and 15mm shall be tapered An additional of 5mm thick PVC sheet of 20mm width is to be stuck on the interior side of 'C' Channel using PVC solvent adhesive etc. complete on both sides to form lock rail.Lock rail shall be provided on either side of panel. Panelling of 4mm thick PVC sheet to be fitted in the MS Frame welded/sealed to the stiles with 8mm (4mm + 4mm) x 12mm wide PVC sheet as beading on inner side and 8mm (4mm + 4mm) x 20mm wide PVC sheet as beading on the inner tapered side of lock rails joined together with solvent cement adhesive. An additional of 4mm thick PVC sheet of 20mm width is to be stuck on the interior side of 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer's specification and drawing.

Providing and Fixing Factory made Adjustable (PVC) Doorframe of the size 65mm x 60mm with a wall thicknes of 4mm, made out of extruded 4mm PVC foam sheet, metre cut at two corners and joined with 2nos. of 150mm long brackets of 15 x 15mm M.S. Square tube. The two vertical door profile are to be reinforced with 40 x 20mm M.S. tube of 19 guage through out the frame. The doorframe shall be fixed to the wall using 65/100mm long M.S. Screw through the frame by using PVC fastners. A minimum of 4 nos. of screws to be provided for each vertical member & minimum 2 nos. for horizontal member etc. complete as per manufacturers specification and direction of Engineer-in-Charge.

35mm thick IInd class hard wood factory made plain, framed, panelled shutter (two panel) with lock rail & panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail & steel as per IS:1003 (Part-I) kiln seasoned & chemically pressure treated.

35mm thick 2nd class hard wood factory made Glazed and skelton shutters open rebated & prepared to receive glass gauze etc (without sash bars) edges of framing plain chamfered / rounded fitted without & mitred beads for securing glass etc size of members of shutters as specified in SSR Part-I Section 8 Clause 8.2 (a) supplied & fitted to chowkats.

Cutting holes in stone / brick walls built in CM for inserting hold fast & making good dismantled portion in CM (1:3) depth of embaded portion of holdfast n. exc half brick

MS butt hinges medium weight, cold rolled size of hinge 100 mm long.

Mild steel sliding door bolt plate type stove enameled black with bright bolt not less than 12mm dia with & including a minimum of 6 bolt & nut four on bolt plate & 2 on staple plate & fixed length of bolt 300 mm

Mild steel pressed handle oval type stove enameled black 125mm size.

MS tower bolt, stove enameled black with bright bolt, length of bolt 150mm.

Preparation and Applying two coats of synthetic enamel paint over a coat of pink primer on wooden surfaces of any description, not otherwise, described, over 10cm width or girth complete all as specified.

S&F Factory made steel ventilators with top hung shutters incl hinge steel peg stay complete incl. taking down old ventilator

S&F Sheet glass 4.0mm thick, ordinary quality & glazing with oil putty in square n exc 0.5 sq.m in each pane. Job No :- 10/REV/61SA/Q3W/2021-22 - 5 Job No :- 09/REV/61SA/Q3W/2021-22 - 2

S&F Galvanised mild steel wire cloth, 0.56 nominal dia of wire & average width of aperture 1.18mm with tinned tacks, or galvanised wire staples

S&F Mild steel bolts purpose made with hexagonal or square head one end and screw the other or screw both ends each screws end to end to be fitted with washer and one hexagonal or square not exc 30cm long all as specified.

S&F steel work in tubular trusses including special shaped washer etc complete using ERW or including induction butt welded tubes conforming 1161-1979 grade st 240 all as specified

S&F Aluminium snap grid frame work of grid size 605 x 605mm for false ceilling all as specified.

M&L for Exposed metal frame ceilling with calcium silicate board of silicious and calcareous material reinforced with cellulose fibre for fixing in 600mm x 600mm grid (frame work for ceilling shall be measured and paid seprately all as specified.

M&L 75 mm thick PCC type C-1 (1:3:6) using 20 mm graded stone aggregate finished even and smooth without using extra cement as in plinth protection

M&L Coloured Glazed ceramic tilessize 300x450mm x 7mm thick edge cut/ joint free , on walls etc. set & jointed in neat cement slurry & pointed in white/coloured cement to match over 15mm thick plaster in CM(1:4) Job No :- 10/REV/61SA/Q3W/2021-22 - 45 Job No :- 09/REV/61SA/Q3W/2021-22 - 34

S&F Coloured Non Skid ceramic tiles 6 to 7mm thick edge cut/ joint free (squares/ rectangular) area of each tile exc. 0.11 sqm but not exc. 0.18 sqm, in floors etc. set & jointed in neat cement slurry & pointed in white or coloured cement to match over 15mm thick screed in CM(1:4)

M&L For coloured Non skid ceramic tiles 7 to 8 mm thick square/rectangular) area of Each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm , in floors etc set jointed in neat cement slurry and pointed in white or coloured cement match over 15 mm thick screed bed in CM(1:4) completed all as specified

M&L For hardcore of gauge n.exc 63 mm,deposited, spread ,and levelled in layers n exc 15 cm thick, watered and rammed to a true surface all as specified. Job No :- 10/REV/61SA/Q3W/2021-22 - 9.50 Job No :- 09/REV/61SA/Q3W/2021-22 - 9.45

S&F sink made of stainless steel 1.0 mm thick for kitchen with plugs, washers and wastes, including bedding in cement mortar on to dwarf wall or with & including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410 x 330 x160 mm including waste pipe of polythelene of low or high density or PVC 32mm dia & waste fitting brass chromium plated for 32mm bore with long screwed shanks and fly nuts including making holes in stone walls for brackets and fixed in CM 1:3 or PCC 1:2:4 type B0 complete.

S&F PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors

S&F PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors

S&F PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints fixed to walls

S&F PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints fixed to walls

S&F PVC (SWR) bends any radius 75mm dia

S&F PVC (SWR) bends any radius 110mm dia

S&F PVC (SWR), junction single, (Single T) equal or unequal 75mm dia

S&F PVC (SWR), junction single, (Single T) equal or unequal 110mm dia

S&F PVC (SWR) vent cowl 110mm dia

S/F Vitreous China wash basin, white, flat back, size 550x400mm but including brackets, coupling and waste pipe complete

S/F stop valves, cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends fancy type chromium plated with long shank and cup (concealed type), 15 mm

S/F brass CP Angle stop cock fancy type concealled type long body,15 mm bore

S/F Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed-15mm

S/F Bib taps, cast copper alloy with crtuch or butterfly handle,screwed down, screwed for iron pipe or for brass ferrule and fixed, fancy type chromium plated long body complete.

S/F PVC connections 15mm size with PTMT nuts of length 300mm

M&L Chromium plated Overhead Rain shower with relvoling joint and 115mm long shower arm with wall flange 15 mm bore fancy type any colour half turn (Make-MARC CAT PART NO MOR 1260 & 1240 or equivalent of GEM , JAQUAR) fixed in repair

S&F in repair Stop valves 20 mm bore, cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions

All as per item No 60 above but of 25mm bore

S&F PVC grating 125mm dia of weight not less than 40gm for floor trap / Nahani trap.

S&F in repairs vitreous china water closet Indian type 580 x 440 mm white with itergal footrest including provn of lime concrete bedding including connections to flushing cistern/pipe and making good disturbed portion to match existing surface complete all as directed including and providing 10 litre capacity low level flushing cistern fixed in repair and 32 mm dia PVC flushing pipe complete all as specified and directed.

S&F Soap dish vitreous china white approximate size 160 x 160 x 90mm equivalent

Preparing new plastered surfaces including scrapping and applying two coat of Dry distemper all as specified and directed by Eng-in-Charge

Demolition of PCC in ground floors and pavings not exc 15cm thickness ( below or above ground level )

Factory made steel window with side hung shutters incl projecting type hinge with steel handle and steel peg stay complete with glazing bars dovetailed or welded incl. taking down old window

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, & steel peg stay, complete without glazing bars, dovetailed or welded incl. taking down old window

S&F Figured glass 4.0mm thick, pin head type & glazing with oil putty in squares n exc 0.5 sq.m in each pane

S&F for Fancy type MS bracket suitable for curtain rod fixed in repair

S&F of 20 mm dia Drapery Fancy type curtain rod fixed in repair

S&F for caps/ side Bulbs PVC suitable for curtain rod fixed in repair

M&L for 100 mm thick PCC 1:4:8 type D2 using 40 mm graded stone aggregate as in floor.

S&F powder coated aluminimum anodised frame fixed type with aluminum section weighing 0.55 kg/mtr incl necessay joining , cleats, glazing clips , rubber packing anodised aluminimum snap beading , screws etc complete all as specified and directed.

S&F powder coated aluminimum anodised door/window shutter openale / sliding type with aluminimum section weighing 0.55 kg/mtr incl necessay joining , cleats, glazing clips , rubber packing anodised aluminimum snap beading , screws handle tower bolt etc complete all as specified and directed. Job No :- 10/REV/61SA/Q3W/2021-22 - 15 Job No :- 09/REV/61SA/Q3W/2021-22 - 27.5

S&F aluminimum (Die cast ) body door closer hydraulically regulated, designation No 2 universal type , suitable for dooe shutter of 701-850mm in width and of weight between 30 to 60 Kg and fixed complete all as specified and directed.

M&L double action door spring hydeaulically regulated mde up of minimum 1.25 mm thick alumunumum alloy , sheet foumdation box main body with stainless steel cover governing pivot made of brass and other parts made of steel heavy duty and fixed complete all as specifiedand directed

S&F 4.00 mm thick frosted glass of ordinary quality and glazing in square as required as directed by Engr -in-Charge.

S&F 5.5 mm thick glass of ordinary quality and glazing in square including solar control film 25mm micron reflective type sticked to glass panes as per instructions of manufacturers .

S&F galvanised mild steel wire cloth 0.36 mm nominal dia of wire with average width of aperture 1.40 mm fixed with tinned tacks or galvanised wire stapels fixed etc complete all as specified and directed.

S&F aluminimum framed work such as grills , gratings etc with ends of bars shouldered and /or riveted, or forged into spikes, framed guard bars and similar works complete all as specified

Brickwork with sub class B bricks straight or curved on plan exc 6mtr mean radius built in CM (1:6) Job No :- 10/REV/61SA/Q3W/2021-22 - 22 Job No :- 17/MIN/61SA/Q3W/2021-22 - 15

JOB No :- 09/REV/61SA/Q3W/2021-22 Surface excavation not exc 30cm deep and averaging 15cm deep and getting out in soft/loose soil. Job No :- 09/REV/61SA/Q3W/2021-22 - 55.60 Job No :- 17/MIN/61SA/Q3W/2021-22 - 20.00

Removal of excavated soil to a distance exc. 250m but not exc. 500m and depositing where directed.

M&L providing pre cast cement concrete block or slab 150mm thick 1:2:4 type B1 using 20mm graded stone aggregate with plain or inter locking joints as directed set in CM 1:6. kerbing/edge block to hard standing/footh including necessary earth work.

M&L for 75mm thick PCC 1:2:4 type B2 using 40mm graded stone aggregate as in floor etc finished fair & even all as specified and directed by Engineer-in-charge.

S&F powder coated aluminium frame for doors, windows ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified.complete all as directed by Engineer-in-Charge.

S&F 5 mm thick tinted glass of ordinary quality all as specified and directed.

M&L 6 mm thick Aluminium Composite panel in partition fixed to aluminium frame work all as specifed and directed by Eng-In-Charge.

Providing and fixing suspended false ceiling make Armstrong ORCAL extra microperforation size 600 x 600 x 15mm ceiling tiles over suspension metal system (MICRO LOOK) designer grid (15mm grid 8mm return) SILHOUETTE X L 15mm (NOMINAL) of Armstrong make complete including necessary hanging system arrangement as per manufactures instruction which is required to be made from existing structure roof/stone slab of building complete all as directed by Engineer-in-Charge.

Taking down Chowkats or frames n.exc 1.5 sq. m each with shutters (without taking off shutters from the frames)

M&L Framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted or forged into spikes; framed guard bars; barred iron doors ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165

S&F 5.5 mm thick plain sheet glass ordinary quality in square exceeding 0.50 Sqm in each pane and glazing with oil putty.

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concretebut excluding ashlar facings, dressed stonework and precast concrete articles.

M&L for brick work with subclass 'B' bricks, straight or curved on plan exc 6 m mean radius built in cement mortar 1:4

M&L for providing precast cement concrete (1:2:4 type B0 using 12.5mm graded stone aggregate) louvers and jallies, 40mm thick (measured solid), including all mouldings but excluding frame, set in CM 1:4 all as specified (Pre cast frame shall be measured separately and paid for under item of BOQ).

M&L for Granite (of any type) work (table rubbed and polished) 16 to 18mm thick in risers & treads of steps, jambs, pillars, window cills,cooking platforms and similar works over & including 20mm thick screed bed (bedding layer) in CM 1:6, pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of Granite including cutting and polishing (half mirror polish i.e. half granite polish as per local trade practice) all as specified & directed by Engineer-in-charge.

S&F light shade Vitrified Ceramic tiles edge cut 10 mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM (1:4) finished fair and even .

Job No :- 17/MIN/61SA/Q3W/2021-22 Removing excavted materails n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point.

M&L for PVC molded of 60 mm thick machine pressed precast concrete interlocking paver block any shape and size bullnosed edge epoxy coated glossy finish confirming to IS 15658-2006 of 60mm tickness , M-35 grade, set, jointed and pointed over and including 25 mm thick sand cushoning all as directed by Engineer-in-Charge.

M&L for 100mm thick PCC 1:3:6 type C2 using 40mm graded stone aggregate as in sub base to floor finished fair & even all as specified and directed by Engineer-in-charge.

Excavation in trenches not exc.1.5 m wide and not exc.1.5 m in depth for foundation or for shafts, walls, manholes etc not exc.10 Sqm on plan and getting out in soft/loose soil.

M&L for PCC 1:4:8 type D2 using 40 mm graded stone aggregate in foundations, filling and mass concrete

M&L for rendering 15mm thick in cement mortar 1:4 on fair faces of brick masonry or concrete surfaces of walls, finished even & smooth without using extra cement.

M&L for providing cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) in lintels upto 1.5m clear span, cills, steps, seismic and othe similar bands, plinth courses, bed plates, copings, kneelers, apex stones, bed plates and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork all as directed by Engineer-in-charge.

M&L Providing precast cement concrete in set in cement mortar 1:4 window or door cills, lintels, bresumers,steps quion blocks (for use with masonary) string courses, coping ,kneelers, apex, stones, pier,caps, coloumn, posts, boundary,pillars, bed plates, pintle,blocks, bonders, (for stone walling) corbles, brackets, etc if any sectionindicated)setting in mortar complete with joints all as specified.

M&L for Providing Precast cement concrete louvers and jallies, 25mm thick (measured solid),set in cement mortar 1:4 type B1 1:2:4(20mm graded aggregate) in cluding all mould ing but excluding frame (precast frame shall be measured separately and paid for under item no 106) all as specified.

Job No :- 10/REV/61SA/Q3W/2021-22 M&L Point wiring complete with 1.5 Sqmm single core PVC insulated and unsheathed multi stranded copper conductor FRLS cable of 1100 V grade PVC insulated and unsheathed cable inclosed in and including concealed PVC conduit medium grade with all accessories ISI marked, including MS sunken box for mounting fitting like switches, sockets fan regulators modulor type etc. including 1.5 sqmm single core PVC insulated but unsheathed copper earth continuty conductor to common earth and connected FRLS cable 1100 V grade as continuous earth wire to earth dolly for followings Make- Havells(std)/Bonton/Polycab/HPL

One light/fan/ bell point controlled by one, one way switch. Job No :- 10/REV/61SA/Q3W/2021-22 - 17 Job No :- 09/MIN/61SA/Q3W/2021-22 - 2

One 3 pin 5 Amp socket outlet on independent board with other switches.

One three pin 5 Amp socket on same board with other switches. Job No :- 10/REV/61SA/Q3W/2021-22 - 2 Job No :- 09/MIN/61SA/Q3W/2021-22 - 2

All as per Item No 108 above but with 2.5 Sqmm copper cable for 3 pin 15 Amps socket outlet on independent board, including 2.5 Sqmm copper cable continuous earth wire and connecting to common earth dolly.

All as per Item No 108 above but with 4 Sqmm copper cable for 3 pin 15 Amps socket outlet on independent board, complete all as specified & directed by Engr-in Charge.

Supply&.Fixing Switch moduler type on top covers (catered in point wiring above):- Make- Havells/Polycab/Anchor/C & S

Single pole, one way 6 Amp rating. Job No :- 10/REV/61SA/Q3W/2021-22 - 24 Job No :- 09/MIN/61SA/Q3W/2021-22 - 4

Single pole, one way 16 Amp rating.

S&Fixing Socket outlet multipurpose use, on top covers (catered in point wiring above) :- Make- Havells (std)/Polycab/Anchor/C & S

5 Pin 6 Amp Job No :- 10/REV/61SA/Q3W/2021-22 - 7 Job No :- 09/MIN/61SA/Q3W/2021-22 - 2

6 Pin 16 Amp

M&L Ceiling rose surface bakelite 65x50mm, three terminals.Make Anchor/Legrand/Crabtree Job No :- 10/REV/61SA/Q3W/2021-22 - 12 Job No :- 09/MIN/61SA/Q3W/2021-22 - 2

Supply & fix T5 integrted batten LED Light fittings 1 x 20 W ,240 volt( size-4 feet/1136 mm) long life, surface/wall mounting IP 20, luminaire per watt (Minium) extruded alluminium housing with frosted PMMA diffuser with high brightness LEDs complete with all accessories pre-wired twin core twisted flexible copper conductor cable with suitable size. Make - Crompton/Bajaj/Wipro/ Philips/CG /Surya roshni Job No :- 10/REV/61SA/Q3W/2021-22 - 6 Job No :- 09/MIN/61SA/Q3W/2021-22 - 1

Supply & fix wall Bracket light asthetically designed with B22d & E27 lamp holder including 10W LED Lamp with all accessories pre-wired twin core twisted flexible copper conductor cable with suitable size. Make - Halonix cat Pt No- HLBW-01-B22 or equivelent model in Bajaj/ Philips/Syska

Supply and Fixing security lights LED 40 W Energy saving & Environmental friendly long life versatile pressure die cast aluminium IP 66 LED Wall mounted Light Luminaries are made of die casted aluminium body and toughened glass cover for uniformlight spread cames LED technology of Britelite. including bracket made out of suitable size of GI medium grade tubing and fixed with clamps nuts and bolts, washer complete all as specified . Make- CG cat Pt No-LSTS-40-CDL or equivalant in HAVELLS ,Syska and Phillips

S &F ceiling fan 1200 mm sweep complet 5 star rating all as specified and directed Make: Havells, khaitan, Usha Job No :- 10/REV/61SA/Q3W/2021-22 - 2 Job No :- 09/MIN/61SA/Q3W/2021-22 - 1

S&F in repair factory made, sheet distribution boards, SP&N 8 ways, double door protection class IP-42 double door type suitable for mounting MCB/ MCCB, confirming to IS-13032, IS-8623, BS-5484 with minimum 200 amps, copper bus bar complete.

S&Fin repair MCB 10 KA confirming to IS-8828 : 1996, IEC-898 : 1995 rupturing capacity of the under mentioned type and rating :-

(a) SP 5 to 32 amps

(b) SPN 32 to 63 amps.

M & L Sub main wiring complete with 2 runs of 6 Sqmm single core PVC insulated unsheathed cable 1100 V grade with multistranded copper conductor ISI marked drawn throughn and including PVC rigid conduit/casing capping and conduit accessories fixed on surface/wall celing etc including provision of 1 run of 4 Sqmm PVC insulated unsheathed cable with multistranded copper conductor as earth continuity.

Supply and fix sheet metal enclosure complete with metallic plug and socket heavy duty moduler type 3 pin (2P + Earth), 25 amp rating single phase 240 volts complete with MCB SP 25 amp “C” series (Make :Havells/HPL/Anchor/havells(std)

Supply & Fixing surface mounted LED mirror light fitting 6 W LED warm white waterproof curve, antique design with fine finishing provide with high power LED, energy saving, lower power consumption, no RF interference, environmental friendly and recyclable, easy for installation water proof LED driver suitable for bathroom, bedroom pre-wired twin core twisted flexible copper conductor cable with suitable size as per sample and as directed by engineer in charge.

S.R.Enterprises

ABHI CONSTRUCTIONS

M/s SM Contractors & Engineers

J.J.ENGINEERING