Proposed Construction of Jharkhand Bhawan at Vashi, Navi Mumbai, Maharastra

Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.5 m.) By Mechanical Means

Filling in plinth and floors with approved excavated material in 15cm. to 20cm. Layers including watering and compacting etc. complete.

Providing and filling in the foundation with sand of approved quality including watering, compacting etc. complete. (To be executed with prior approval of Superintending Engineer)

Providing and laying Cast in situ/Ready Mix cement concrete in M15 of trap/ granite/quartzite/gneiss metal for foundation and bedding / steps including steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface, only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.),with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and laying Cast in situ/Ready Mix cement concrete in M-10 of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including bailing out water, Steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and laying damp proof course 50 mm thick in M20 cement concrete layer and bitumen / using cement with waterproofing compound curing, formwork etc. complete.

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-Ill) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Providing preconstructional antitermite treatment as per I.S. 6313 (Part-II) by treating the bottom surface and sides of excavation at the rate of 5 litres of emulsion concentrate of 1.0 percent of chlorophyrifos per square meter of surface area covering 10 years guarantee on bond paper.

Treatment of soil under existing floors using chemical emulsion @one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement: 2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Providing and laying cast in situ / Ready Mix Cement Concrete M-30 for bored piles each of load capacity and as per design and of 600 mm diameter or as directed placed through steel shells sunk to the required depth through all strata except rock excluding provision of reinforcement as per detailed drawings and design approved by the Engineer-in- charge including placing with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) by tremie arrangements, compaction of concrete including chipping and dressing and withdrawal of shell etc. complete. (Excluding steel reinforcement)

Providing and laying cast in situ / Ready Mix Cement Concrete M-30 for bored piles each of load capacity and as per design and of 800 mm diameter. or as directed placed through steel shells sunk to the required depth through all strata except rock excluding provision of reinforcement as per detailed drawings and design approved by the Engineer-in- charge includingplacing with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) by tremie arrangements, compaction of concrete including chipping and dressing and withdrawal of shell etc. complete. (Excluding steel reinforcement)

Carrying out load test for 1.5 times the proposed safe working load on the pile in driven position above 600 mm and upto 825 mm diameter including construction of test cap, use of accessories and instruments including providing graphs as per I.S. code or Std.Specifications and dismantling the test cap after testing and cleaning the site complete. (Single Pile)

Carrying out load test for 1.5 times the proposed safe working load on the pile in driven position above 750 mm and upto 825 mm diameter including construction of test cap, use of accessories and instruments including providing graphs as per I.S. code or Std.Specifications and dismantling the test cap after testing and cleaning the site complete. (Two or More Piles)

Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap / granite/quartzite/ gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. including bailing out water, Steel centering, formwork ,cover blocks, laying/pumping, compaction and curing roughening the surface if special finish is to be provided (Excluding reinforcement and structural steel) etc. complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap / granite/quartzite/ gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. columns as per detailed designs and drawing or as directed including Steel centering formwork, cover blocks laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and laying Cast in situ/Ready Mix cement concrete M-40 of trap / granite/quartzite/ gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. columns as per detailed designs and drawing or as directed including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap / granite /quartzite/ gneiss metal for R.C.C. columns as per detailed designs and drawing or as directed including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete.(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and laying Cast in situ/Ready Mix cement concrete M-40 of trap / granite/quartzite/ gneiss metal for R.C.C. columns as per detailed designs and drawing or as directed including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Extra for R.C.C./ B.M.C/ R.M.C. work above floor V level for each four floors or part thereof.

Add for using extra cement in the items of design mix over and above the specified cement content therein.

Providing and fixing in position to the exact profile and prestressing the high tensile strands to specified ultimate strength, standard end anchorages, cable ducts, grouting ducts after prestressing and bearing plates with wedges as per detailed drawings including necessary plant and machinery for prestressing etc. complete.

Extra for providing and fixing expanded metal mesh of size 20x60 mm and strands 3.25 mm wide 1.6 mm thick weighing 3.64 kg per sqm f or encasing of rolled steel sections in beams, columns and grillages, excluding cost of hangers.

Providing and fixing in position HCRM / CRS (Corrosion Resistant Steel) bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete.

Providing and fixing in position HCRM / CRS (Corrosion Resistant Steel) bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings /wooden frames with rawl plugs screws etc.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete Hot finished welded type tubes

Providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc. including welding grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts, etc. of the required size on the top of the floor of the side of waiste slab with suitable arrangement as per approval of engineer in charge (for payment purpose, only the weight of the stainless steel members shall be considered excluding fixing accessories such as nut bolts, fasteners etc.). 50mm dia. pipe, 1.5mm thickness and weight 1.92Kilogram/ r. metre

Toughned Glass 12mm

Providing structural steel work in trusses, other similar trussed purlins and members with all bracing, gusset plates etc. as per detailed designs and drawings or as directed including cutting, fabricating, hoisting, erecting fixing in position, Making riveted/ bolted/ welded connection and one coat of anticorrosive paint and over it 2 coats of oil painting approved quality and shade etc. complete.

Providing internal cement plaster 12mm thick in single coat in cement mortar 1:4 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etc. complete.

Providing internal cement plaster 12mm thick in single coat in cement mortar 1:5 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etc. complete.

Providing internal cement plaster 6 mm thick in a single coat in cement mortar 1:4 without neeru finish to concrete surface in all positions including scaffolding and curing etc. complete.

Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 mm thick in cement mortar 1:4 using waterproofing compound at 1Kilogramper cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete.

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof.

Third floor

Fourth floor

Fifth floor

Sixth floor

Sventh floor

Parapet + Mumty

Providing and applying Royale Luxury Emulsion of approved make on internal wall surface as detailed below Scrapping for surface with emery paper and wipe clean for area. wall primer with brush by adding mineral turpentine oil by 8 to 10 % or water by 15 to 20% allowing to dry for 6 to 8 hoursAfter applying acrylic wall putty with appropriate prpportion of water of allow to dry for period of 4 to 6 hours of activity. Scrapping with emery paper and wipe clean Applying paints Royale Luxury emulsion 1st coat with brush water content water 40 to 45% or 65 to 70% by role Applying paints Royale luxury emulsion 2nd coat with brush with water content 40 to 45% or 65 to 70 % by roller. (With prior approval of S.E.)

Providing and applying two coats of exterior weather shield paint of approved manufacture and of approved colour to the plastered surfaces including cleaning ,preparing the plaster surface ,applying primer coat ,scaffolding if necessary, and watering the surface for two days etc complete. NOTE: For Item One Number 15 to 18 prior approval of Superintending Engineer will be necessary

Providing and applying laying Aggregate plaster in granite / marble stones, as decorative finish to give granite / marble like appearance to concrete, brick or block surfaces in all position including preparation of surface smoothly, evenly by racking of joints in case of Brick or block work including backing layer of 12 mm thick with cement mortar 1:3 with 2% integral cement water proofing compound, roughening for wall keying hardening and drying the surface for a minimum five days gaps including second coat of cement lime mortar into a proportion 1:4 preparing the surface for three coat of marble finish plaster giving a thin coat of white cement and two parts of course calcite powder, applying the mortar with steel float on the surface in proper evenness applying at coat of white cement and lime to set a smooth finish then applying a thin coat of slurry made of white cement and black oxide colour in required proportion by the steel float to get black streaks on the surface and curing the surface for two days including all materials and labour etc. complete.NOTE: TEXTURE OF DHOLPUR/RED SAND STONE

Extra for brick work / AAC block masonry / Tile brick masonry in superstructure above floor V level, for each four floors or part thereof by mechanical means

Sixth Floor -6.47 B

Seventh Floor-6.47 C

Terrace -6.47 D

Providing Autoclaved Aerated Concrete Block masonary of conforming to IS:2185 (Part 3) - 1984 in extra fine jointing mortar of fixoblock of UltraTech or equivalent in superstructure including striking joints, raking out joints and scaffolding etc. Complete. (The test shall be carried out conforming to IS:6441 (Part I) - 1972)

Providing and laying telephone black / Amba White / Cadburybrown / Ruby red / Ocean Brown granite stone of 18 to 20 mm thick for door frame/ dado/ window boxing etc. On C.M. 1:6 including filling joints with polymer base filler nosing/moulding the sharp edges wherever necessary, curing, etc. complete.

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.

Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete.

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth Granite Stone of approved shade

Providing and laying machine cut, mirror polished Marble stone flooring, in required design (Simple geometrical, abstract etc.) and in patterns in combination with Italian marble stones of different colours, shades and f inished surface texture etc., in linear portions of the building, all complete as per the architectural drawings, with 18 mm thick stone slab laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm, including pointing with white cement slurry admixed with pigment to match the marble shade, including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. 18 mm thick Italian Marble stone slab, Perlato, Rosso verona, Fire Red or Dark Emperadore etc.

Providing and Fixing Processed Stone Cladding on wall surface/ plywood surface. RCC pardi/ Wall and all type of Interior, Exterior Compound wall and Gate etc. of cladding processed stone with material of Processed clay, Wooden chips, Silica sand, Cement, GFRC admixtures, Colour pigments, Fiber up to thick of 230 mm/ 25 mm including scaffolding, fixing of screw, etc. (As directed by Engineer in Charge)-NOTE WHITE SAND STONE-30MM TO BE USED

Dry wall cladding with clay tile; Designing, supplying and fixing of Clay tile of Wienerberger (Red Series or Grey Series) or Equivalent with suitable size and thickness not less than 20 mm as per manufacturer with approved colour and pattern with composition of finest powdered clay and colour mixtures. The clay tile shall be fixed on the suitable farming system by using continuous aluminium profiled section as per manufacturer with suitable size and spacing to withstand the structural design criteria specifled in the technical specification by using necessary HDG brackets, SS316 grade anchor bolts etc as per manufacturer specification. Cladding joints should be with open groove system. with prior approval of concerned Superitending Engineer-RED SAND STONE -30MM TO BE USED

Providing and fixing stainless steel cramps of required size and shape for anchoring stone wall lining to the backing or securing adjacent stones in stone wall lining in cement mortar 1:2 (1 cement : 2 coarse sand), including making the necessary chases in stone and holes in walls wherever required.

Providing and fixing copper pins 7.5 cm long 6 mm diameter for securing adjacent stones in stone wall lining in cement mortar 1:2 (1 cement : 2 coarse sand), including making the necessary chases.

Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive), coMRsting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S.fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete. 75 mm overall thickness partition with 12.5 mm thick double skin fire rated Glass Reinforced Gypsum (GRG) plaster board conforming to IS: 2095: part 3 (Board with BIS certification marks)

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). Second class teak wood

Providing and fixing ISi marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters 35 mm thick including ISi marked Stainless Steel butt hinges with necessary screws

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high deMRty protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.5 mm thick

Providing and fixing wooden moulded beading to door and window f rames with iron screws, plugs and priming coat on unexposed surface etc. complete : 2nd class teak wood 50x12 mm

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Clerestory windows & other Frames/ Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5 mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. Frame size 65 x 150 mm

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of f lame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) 35 mm thick

Providing and fixing 18 mm thick, 150 mm wide pelmet of coir veneer board ISi marked IS : 14842, including top cover of 6 mm coir veneer board, nickle plated M.S. Pipe 20 mm dia. (heavy type) curtain rod with nickel plated brackets, including fixing with 25x3 mm M.S. Flat 10 cm long f ixed to pelmet with hollock wood cleats of size 100 mm x 40 mm x 40 mm on both inner side of pelmet and rawl plugs 75 mm long etc. all complete.

Extra for using veneered particle board conforming to IS 3097 Grade I, in item of pelmet 18 mm thick 150 mm wide. Particle board with decorative veneering on both sides

Providing and fixing fire resistant door frame of section 50 x 60 mm on horizontal side & 35 x 60 mm on vertical sides having built in rebate made out of 1.6 mm thick GI sheet ( Zinc coating not less than 120gm/ m²) suitable for mounting 120 min Fire Rated Glazed Door Shutters. The frame shall be filled with Mineral wool Insulation having deMRty min 96Kg/m³ . The frame will have a provision of G.I. Anchor fastners 14 nos ( 5 each on vertical style & 4 on horizontal style of size M10 x 80 ) suitable for fixing in the opening along with Factory made Template for SS Ball Bearing Hinges of Size 100x89x3mm for fixing of fire rated glazed shutter . The frame shall be finished with a approved fire resistant primer or Powder coating of not less than 30 micron in desired shade as per the directions of Engineer - in- charge . (Cost of SS ball bearing hinges is excluded).

Providing and fixing 60 mm thick glazed fire resistant door shutters of 120 min Fire Rating confirming to IS:3614 (Part II) or EN1634-1:1999, tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, top rail & side rail 60 mm x 60 mm wide and bottom rail of 110 mm x 60 mm made out of 1.6mm thick G.I. sheet (zinc coating not less than 120gm/m²) duly filled mineral wool insulation having density min 96 kg/ m³ and fixing with necessary stainless steel ball bearing hinges of size 100x89x3mm of approved make, including applying a coat of approved fire resistant primer or powder coating not less than 30 micron etc all complete as per direction of Engineer-in-charge (panelling to be paid for seperately).

c) Vision Panel: 2 HR rated E Class clear high stress fire rated glass is pre fabricated strategically inside the shutter structure with 10 mm inside the shutter on all sides with U- glazing. An additional insulated powdercoated 'Z' channel of 16 swg MS sheet to be fixed for reinforcement of the joints.

Panic Bar: (For 2 Hr fire Rated single Panic bar) Supplying, fitting & fixing Surface mounted Crash Bar /panic Bar of touch pad style, made of heavy duty cast iron/ steel body & latches with SS, BHMA certified & conforming to ANSI A 156.3 for grade-1 (3 hours fire rated) and suitable for surface mounting to wooden/ hollow metal/ Al framed door, with maximum operating force 8 Kilogram for unlocking easily & outwardly during emergency, complete in all respect as per direction & satisfaction of Engineer-in charge including all taxes & incidental charges. (Note: To be installed at "FIREEXIT" only under location specificin struction of Eingineer-in -Charge.)

Door Closure: (For 2 Hr fire Rated EN-3 Door Closure) Supplying, fitting & fixing Surface mounted overhead Door Closer for 2 hour fire rated doors of different size (e.gsize-EN-3 for leaf width upto 900mm) CE certified, marked & conforming to EN-1154 of approved quality (Internationally reputed brand like Dorma, Geze, Hafele, Assabloy & Magnum etc.) fitted and fixed Complete as per direction & satisfaction of Engineer -in Charge including all taxes & incidental charges.

Providing and fixing ready made 304 grade stainless steel Modular kitchen basket and accessories such as right angle basket (Plain Cup & Saucer, plant, Partition, Bottle rack, Thali, Cutlery) kitchen utensil basket, Dinner set basket, kitchen grain basket, Multipurpose basket as per site requirement including finishing (wherever required) and fittings. The same shall be fixed with necessary stainless steel nuts & bolts, Stainless Steel screws & telescopic channel etc. as per direction of Engineer-in- charge. (For payment purpose only weight of Stainless steel basket shall be considered excluding weight of all fixing accessories such as nuts, bolts, fasteners telescopic basket channels etc. Payment of providing and fixing telescopic channel shall be paid separately)

Providing and fixing of factory made uPVC Sliding window & door (White Colour) complete, comprising uPVC multi-chambered frame having in-built uPVC roller track on top and uPVC sash with wall thickness of 2.3mm (+-0.2 mm), duly reinforced with G.I. section 1.5 mm, wherever required. uPVC window & door profile shall be made in India & shall conform to BS EN 12608 and other standards as mentioned below: S.No. Name of the test Test Method Specified Parameter 1 Tensile Impact Strength ISO 8256 - more than 700Kj/m2 2 Vicat Softening Temperature EN ISO – 306 Shall not be < 750C 3 Charpy Impact Strength EN ISO – 179-2 Shall not be < 20KJ/m2 4 Flexural Modulus Elasticity EN ISO – 178 Shall not be < 2200 N/mm2 5 Mean Breaking Stress for welded corner (a) For the tensile bending test EN – 514 Shall not be < 25 N/mm2 (b) For the compression bending test Shall not be < 30N/mm2 6 Heat Reversion Test IS:4985-2000 Shall not be > 2.0 % 7 Surface Spread of flame BS : 476 - Part 7 Classification 1 8 Ignitability Evaluation BS : 476 - Part 5 'P' Not easily ignitable 9 Tensile modulus ASTM D 638 Shall not be < 35 MPa 10 Shear Modulus ASTM D 732 Shall not be < 220 MPa 11 Tensile Strength EN ISO 527 Shall not be < 30 MPa All corners of frame and sash will be fusion welded. After placing 5 mm Float Annealed glass in the sash, uPVC glazing bead, interlock, EPDM / TPE gasket, brush shall be provided including touch lock and rollers & proper drainage system shall be provided. Window / Door will be fixed to the wall with 100mm long and 8mm dia. Fasteners and complete in all respect as per direction of Engineer-In-Charge. uPVC Window and Door Profiles are warranted for a period of ten (10) years against non-uniform discoloration, wrapping and rotting under general use.

3 Track with Mesh-2 Glass Sash + 1 Mesh Sash (Each sash shall be half of width of window) (Big Series) Window frame of size 122 x 54 mm & Sash of size 64 x 47 mm.

Fixed window/ ventilator with mullion/ transom. Using R2 series with frame (39 mm & above ) x (39 mm & above) & mullion (39 mm & above) x (60 mm & above). (Height upto 1.2 metre)

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily Glazed Vitrified tiles Matt/Antiskid finish of size Size of Tile 1200 x 1200 mm sqm

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed vitrified floor tiles polished finish of size Size of Tile 800 x 1600 mm s

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc coMRsting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge : With average thickness of 120 mm and minimum thickness at khurra as 65 mm.

Grading roof for water proofing treatment with Cement concrete 1:2:4 (1 cement : 2 coarse sand :4 graded stone aggregate 20mm nominal size)

Providing and applying integral crystalline (dry shake) of hydrophilic in nature for waterproofing treatment to the RCC structures like basement raft, foundation slab, sewage & water treatment plant slab, warehouses f loor, parking structures and water tank base slab etc. sprinkled @0.60 kg per sqm or higher as recommended by the manufacturer’s specification over the lean concrete of above cited structures. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e. by reducing permeability of concrete by more than 85%, compared control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline dry-shake shall be capable of self-healing of cracks up to a width of 0.50 mm. The work shall be carried out all complete as per specification and the direction of the Engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage.

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50 mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage. For vertical surface two coats @ 0.70 kg per sqm per coat

For horizontal surface one coat @1.10 kg per sqm

Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. (The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account).The weight of aluminium extruded section shall be taken for purpose of payment.

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including: Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)- cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including:

Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimentional movement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/structural steel framework of building structure using stainless steel anchor fasteners/ bolts, nylon separator to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers. Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shop environment , including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand and manufacture, as per the approved sealant design, within and all around the perimeter for holding glass.

Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site conditions, to seal the gap between the building structure and all its interfaces with curtain glazing to make it watertight. Making provision for drainage of moisture/ water that enters the curtain glazing system to make it watertight, by incorporating principles of pressure equalization, providing suitable gutter profiles at bottom (if required), making necessary holes of required sizes and of required numbers etc. complete. This item includes cost of all inputs of designing, labour for fabricating and installation of aluminium grid, installation of glazed units, T&P, scaffolding and other incidental charges including wastages etc., enabling temporary structures and services, cranes or cradles etc. as described above and as specified. The item includes the cost of getting all the structural and functional design including shop drawings checked by a structural designer, dully approved by Engineer-in-charge.

The item also includes the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working structural glazing as specified, cleaning and protection till the handing over of the building for occupation. In the end, the Contractor shall provide a water tight structural glazing having all the performance characteristics etc. all complete as required, as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer- in-Charge. having all the performance characteristics etc. all complete as required, as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer- in-Charge. Note:- 1. The cost of providing extruded aluminium frames, shadow boxes, extruded aluminium section capping for fixing in the grooves of the curtain glazing and vermin proof stainless steel wire mesh shall be paid for separately under relevant items under this sub- head. However, for the purpose of payment, only the actual area of structural glazing (including width of grooves ) on the external face shall be measured in sqm. up to two decimal places. Note:- 2. The following performance test are to be conducted on structural glazing system if area of structural glazing exceeds 2500 Sqm from the certified laboratories accreditated by NABL(National Accreditation Board for Testing and Calibration Laboratories), Department of Science & Technologies, India. Cost of testing is payable separately. The NIT approving authority will decide the necessity of testing on the basis of cost of the work, cost of the test and importance of the work. Performance Testing of Structural glazing system Tests to be conducted in the NBL Certified laboratories

Performance Laboratory Test for Air Leakage Test (-50pa to - 300pa) & (+50pa to +300pa) as per ASTM E-283-04 testing method for a range of testing limit 1 to 200 mVhr Static Water Penetration Test. (50pa to 1500pa) as per ASTME- 331-09 testing method for a range up to 2000 ml. Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01- 05 testing method for a range upto 2000 ml Structural Performance Deflection and deformation by static air pressure test (1.5 times desing wind pressure without any failure) as per ASTME-330-10 testing method for a range upto 50 mm Seismic Movement Test (upto 30 mm) as per AAMA 501.4-09 testing method for Qualitative test. Tests to be conducted on site. OMRte Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi) upto 2000 ml

Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthened clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor.“(Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.26.2)“For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm.“ (i) Coloured tinted float glass 6 mm thick substrate with reflective soft coating on face # 2, + 12 mm Airgap + 6 mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement.

Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer- in-Charge.

Design supply & installation of suspended Spider Glazing system designed to withstand the wind pressure as per IS 875 (Part-III). The Suspended System held with Spider Fittings of SS-316 Grade Steel of approved manufacturer with glass panel having 12 mm thick clear toughened glass held together with SS- 316 Grade Stainless steel Spider & bolt assembly with laminated glass fins 21 mm thick. The Glass fins and glass panel assembly shall be connected to Slab/beams by means of SS- 316 Grade stainless steel brackets & Anchor bolts and at the bottom using SS channel of 50x25x2 mm using fastener & anchor bolts, non staining weather sealants of approved make, Teflon/ nylon bushes and separators to prevent bi-metallic contacts, all complete to perform as per specification and approved drawings. The complete system to be designed to accommodate thermal expansion & seismic movements etc. The joints between glass panels (6 to 8 mm) and gaps at the perimeter & in U channel of the assembly to be filled with non staining weather sealant, so as to make the entire system fully water proof & dust proof. The rate shall include all design, Engineering and shop drawing including approval from structural designer, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. all complete. For the purpose of payment, actual elevation area of Glazing including thickness of joints and the portion of Glass panel inside the SS channel shall be measured.

Providing and fixing double scaffolding system (cup lock type) on the exterior side of building/structure, upto 25 metre height, above ground level, including additional rows of scaffolding in stepped manner as per requirement of site, made with 40 mm dia M.S. tube, placed 1.5 metre centre to centre, horizontal & vertical tubes joint with cup & lock system with M.S. Tubes, M.S. tube challis, M.S. clamps and staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for execution of work of cleaning and/ or pointing and/ or applying chemical and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connecting with the building etc, wherever required, if feasible, for inspection of work at required locations with essential safety features for the workmen etc., complete as per directions and approval of Engineer-in-charge. Note:- (1) The elevational area of the scaffolding shall be measured for payment purpose. (2) The payment will be made once only for execution of all items for such works.

Providing and fixing 15 mm thick eco-friendly densified edge calcium silicate false ceiling of approved texture of size 595mm x 595mm in true horizontal level, suspended on interlocking metal grid of hot dipped galvanized steel sections (galvanising at @12 gm/sq.m including both sides) consisting of main T runner suitably spaced at joints to get required length and size 24X38mm. made from 0.33mm thick(minimum ) sheet, spaced 1200mm center to center and cross T of size 24X28mm made of 0.33mm thick(minimum ) sheet to be interlocked at the middle of the 1200x600 mm panel to form the grid of size 600x600mm resting on periphery walls/partitions on a perimeter wall angle precoated steel of size 24x24x3000 made of 0.4 mm thick (minimum) sheet with the help of all plugs at 450mm and laying 15 mm thick densified edges calcium silicate ceiling tiles of approved texture (spintone/cosmos/hexa) in the grid, including light fittings , fixtures , smoke detectors etc., wherever required. Main T runners suspended from ceiling with using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling using 12.5mm dia. And 50mm long dash fasteners, 4mm G.I. adjustable rods with galvanized steel levels clips of size 85x30x0.8mm, spaced at 1200mm center to center along main T bottom exposed with 24mm of all T-sections shall be prepainted with polyester baked paint, for all heights, as per specifications, drawings etc. complete.(currently this item should be used only for VIP cabins)

Providing and fixing false ceiling at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity < 0.043 W/m K as per ASTM 518:1991, in true horizontal level suspended on inter-locking metal powder coated T-Grid of hot dipped galvanised iron section of 0.40 mm thick on Silhouette profile,rotary stiched double webbed white with 6 mm reveal profile (white/ black),comprising of main-T runners of size 15x42 mm of length 3000 mm, cross - T of size 15x42 mm of length 1200 mm and secondary intermediate cross-T of size 15x42 mm of length 600 mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 22x19x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall S.S screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge With 15 mm thick integral densified micro edge light weight calcium silicate false ceiling tiles

Providing and fixing false ceiling at all heights including providing and f ixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x1 0x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and f inishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum moisture resistant board

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing ISI 1729/2002 grade 100 mm dia Cast Iron Soil Pipes With lugs including plug bend necessary fittings such as bends, tees, single junction, double junction, slotted vent, offsets on wall or into the ground including filling joints with cement mortar 1:2 proportion fixing on wall by means of galvanised Mild Steel bracket of 30 x 5 mm plate and 8 mm square rod with Galvanised Iron clamp with washer as per design, drawing and as directed to keep pipe 50 mm away from wall including necessary scaffolding and painting the exposed faces with one coat of red lead oil paint and two coats of white oil paint including removing the existing pipe if necessary and conveying and stacking in PWD Chowky or as directed by Engineer-in-Charge.

Providing and fixing ISI 1729/2002 grade 75 mm dia Cast Iron Waste Water Pipe with lugs necessary fittings such as bends, tees, single junction, double junction, slotted vent, offsets on wall or into the ground including filling joints with cement mortar 1:2 proportion fixing on wall by means by galvanised Mild Steel bracket of 30 x 5 mm plate and 8 mm square rod with Galvanised Iron clamp with washer as per design drawing and as directed to keep pipe 50 mm away from wall including necessary scaffolding and painting the exposed faces with one coat of red lead oil paint and two coats of gray oil paint including removing the existing pipe if necessary and conveying and stacking in PWD Chowky or as directed by Engineer-in-Charge.

Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 ( 1 cement : 2 fine sand) in S.C.I./ C.I. Pipes :

Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter

Providing and making lead joints for 100mm diameter cast iron pipes line including lead and testing.

Providing and making lead joints for 80mm diameter cast iron pipe line including lead and testing.

Providing and fixing M.S. stays and clamps for sand cast iron/ centrifugally cast (spun) iron pipes of diameter :

Cutting chases in brick masonry walls for following diameter sand cast iron/ centrifugally cast (spun) iron pipes and making good the same with cement concrete 1:3:6 ( 1 cement : 3 coarse sand :6 graded stone aggregate 12.5 mm nominal size), including necessary plaster and pointing in cement mortar 1:4 (1 cement : 4 coarse sand) :

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge

100 mm nominal dia Pipes

150 mm nominal dia Pipes

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

Providing and fixing P.V.C. Rain water pipes of 110mm outer diameter and having wall thickness of 2.2 to 2.7 mm confirming to I.S. 13592-1992 including proper rainwater receiving recess with P.V.C. plug, bend, necessary fittings, such as, offsets, shoes, inluding fixing the pipe on wall using approved wooden cleats projecting 25mm to 40mm from face of wall a fixing with clips of approved quality and One Number ,filing the joint using rubber gasket with solvent cement and properly resting the shoe of pipes on C.C. or masonry blocks, including necessary scaffolding and maintenance for 3 yrs for any leakages or dislocations of pipes. All the P.V.C. fittings and additional 2 piece socket clips shall be got approved from engineer in charge etc. complete.

Providing and fixing P.V.C. Rain water pipes of 160mm outer diameter and having wall thickness of 2.2 to 2.7 mm confirming to I.S. 13592-1992 including proper rainwater receiving recess with P.V.C. plug, bend, necessary fittings, such as, offsets, shoes, inluding fixing the pipe on wall using approved wooden cleats projecting 25mm to 40mm from face of wall a fixing with clips of approved quality and One Number ,filing the joint using rubber gasket with solvent cement and properly resting the shoe of pipes on C.C. or masonry blocks, including necessary scaffolding and maintenance for 3 yrs for any leakages or dislocations of pipes. All the P.V.C. fittings and additional 2 piece socket clips shall be got approved from engineer in charge etc. complete.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.

15 mm nominal dia Pipes

20 mm nominal dia Pipes

25 mm nominal dia Pipes

32 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work

Providing and fixing on walls/ ceiling/ floor 15 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing on walls/ceiling/floor 20 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing on walls/ ceiling/ floor 25 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing on walls/ ceiling/ floor 32 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing on walls /ceiling/ floor 40 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing on walls/ ceiling/ floor 50 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete.

65 mm nominal dia Pipes

80 mm nominal dia Pipes

100 mm nominal dia Pipes

150 mm nominal dia Pipes

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :

15 mm nominal dia Pipes

20 mm nominal dia Pipes

25 mm nominal dia Pipes

Providing and fixing gun metal non- return valve of approved quality (screwed end) :

25 mm nominal bore- Horizontal

25 mm nominal bore- Vertical

32 mm nominal bore- Horizontal

32 mm nominal bore- Vertical

40 mm nominal bore- Horizontal

40 mm nominal bore- Vertical

50 mm nominal bore- Horizontal

50 mm nominal bore- Vertical

65 mm nominal bore- Horizontal

65 mm nominal bore- Vertical

80 mm nominal bore- Horizontal

80 mm nominal bore- Vertical

Providing and fixing brass ferrule with C.I. mouth cover including boring and tapping the main :

Providing and making ISI Mark ferrule connection of 15 mm dia. to water main including ferrule coupling cast iron bell mouth cover, built in non return valve and fixing including excavation and reinstatement complete.

Providing and making ISI Mark ferrule connection of 20 mm dia. to water main including ferrule coupling cast iron bell mouth cover, built in non return valve and fixing including excavation and reinstatement complete.

Providing and making ISI Mark ferrule connection of 25mm dia.to water main including ferrule coupling cast iron bell mouth cover, built in non return valve and fixing including excavation and reinstatement complete.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe

32 mm dia

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board

510x1040 mm bowl depth 250 mm

Providing and fixing uplasticised PVC connection pipe with brass unions :

45 cm length -15 mm nominal bore

45 cm length -20 mm nominal bore

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :

Providing and laying concrete pipes of I.S.NP. class of 100mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete.

Providing and laying concrete pipes of I.S.NP. class of 150mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete.

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design :

100 mm diameter S.W. pipe

150 mm diameter S.W. pipe

200 mm diameter S.W. pipe

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x 300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:

180x150 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :

Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (heavy duty) 560 mm internal diameter, total weight of cover and frame to be not less than 208 kg (weight of cover 108 kg and weight of frame 100 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for depth for manholes : Extra for depth for manholes :Size 120x90 cm With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry road gully chamber 110x50x77.5 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm precast R.C.C. horizontal grating with frame and vertical grating complete as per standard design : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Excavating trenches by mechinical / manual means of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, for all depth, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kinds of soil Pipes, cables etc. exceeding 300 mm dia but not exceeding 600 mm

Constructing masonry Chamber 120x120x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size), including necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Providing and fixing white Opal series European type wall-hung, of size 400 mm x 370 mm x 575mm with approved make flush valve including soil pipe, vent pipe upto outside face of wall, 100mm dia C.I. plug bend inlet pipe all fittings, cutting & making good walls, floors etc as directed by Engineer in charge.

Providing and fixing white european type wall-hung pan, of size 350mm x 355mm x 570 mm concealed flush tank with floor-mounting frame installing kit and drain pipe connection set for wall hung WC, with approved make square control plates including soil pipe, vent pipe upto the outside face of wall, 100mm dia C.I. plug bend inlet pipe all fittings,cutting & making good walls, floors etc. complete.

Providing and fixing Oval Type Under Counter Wash Hand Basin of 420 x 590 x 195mm size with pillar cock, C.P.Angular stop cock, long thread of approved make continental including SS bottle trap of necessary pipe connection up to the outside face of the wall, having Telephonic Black / Colour Granite of 180 mm thick fixed on Black Kadappa Framework, etc. Complete as directed by Engineer in charge.

Providing and fixing toilet paper holder : C.P. brass

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore

Providing and fixing divertor with overhead shower,shower arm,spout,hand shower with wall bracket having flow rate up to 12 liters/minutes of Jaquar/Cera/Hindware /Perryware or equivalent make including all necessary pipes,fittings etc.complete as directed by Engineer In Charge.( Make shall conform to manufacturer's Green product and shall got approved from the Engineer In Charge.)

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : 150 mm diameter

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15 mm nominal bore

Providing & fixing chrome plated brass battery based infrared sensor operated pillar cock, having foam flow technology. 15 mm nominal bore

Providing and fixing wash basin with C.I. brackets, 15 mm PTMT pillar cock, 32 mm PTMT waste coupling of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required. White Vitreous China Flat back wash basin size 550x400 mm with single 15 mm PTMT pillar cock.

C.P. Brass Centre Hole Basin Mixer With Cast Spout

Providing and fixing white glazed urinal of size 710x460x300mm with sensotronic concealed type flushing valve for urinal with complete kit having fittings, inlet pipe with stop tap, brackets for fixing the cistern, 32mm diameter P.V.C. flush pipe with fitting and flushing arrangement including lead soil pipe, lead trap & soil pipe connection upto the outside face of wall etc complete.

Providing and fixing CP Brass 32 mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.

Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers etc if required will be paid separately) :

50 mm dia

80 mm dia

100 mm dia

Providing and fixing enclosed type water meter (bulk type) conforming to IS : 2373 and tested by Municipal Board complete with bolts, nuts, rubber insertions etc. (The tail pieces if required will be paid separately) :

80 mm dia nominal bore

100 mm dia nominal bore

150mm dia nominal bore

200 mm dia nominal bore

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement: 4 coarse sand) and making good the wall etc. complete.

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Group C

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Supplying and drawing following size frls pvc insulated copper conductor single core cable in surface/recessed pvc conduit as required.

2 x 2.5sqmm. + 1 x 1.5sqmm earth wire

2 x 4sqmm. + 1 x 2.5sqmm earth wire

2 x 6sqmm. + 1 x 2.5sqmm earth wire

4 x 6sqmm. + 1 x 4sqmm earth wire

4 x 16sqmm. + 1 x 6sqmm earth wire

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required.

Supplying and erecting Energy Saving BLDC Ceiling fan 230 V A.C. 50 cycles 1200 mm, max. energy consumption of 28W having service ratio (CMM/W) of Min. 8 , PF>0.9, THD

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

4 way (4 + 12), Double door

6 way (4 + 18), Double door

8 way (4 + 24), Double door

Supplying and fixing following way, horizontal type single pole and neutral, sheet steel, MCB distribution board, 230 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

12 way, Double door

Supplying and fixing 5 A to 32 A rating, 240 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required

10A Single Pole

16A Single Pole

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

300 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "bends" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc.as required

300 mm width X 50 mm depth X 1.6 mm thickness

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or inrecess for connections etc. as required.

Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.

Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolting/ sweating and soldering etc as required.

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run).

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run).

Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required.

Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required.

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required

upto 35 sq. mm

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Above 185 sq. mm and upto 400 sq. mm

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

3½ X 70 sq. mm

3½ X 95 sq. mm

3½ X 150 sq. mm

3½ X 300 sq. mm

4 X 16 sq. mm

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc. complete as required.

160 mm dia

Design, Fabrication, Supply, Erection,Testing and commisioning of Powder coated Indoor Type Panel fabricated out of 14 guage CRCA sheet steel in cubical, compartmentallised, free standing , dust and vermin proof, (degree of protection-IP54)with reinforcement of suitable size angle iron, channel, T -iron or flats as required. Cable gland plates shall be provided on top as well as bottom of the panels. Panels shall be treated with all anti-corrosive process before painting as per specification. Panels shall be suitable for 415V, 3-Phase, Four wire, 50 Hz supply complete with earth bus and lifting hooks as required in case of large panels.Approval shall be taken for each panel before fabrication. (All hardwares like nuts and bolts used shall be Galvanized and Zinc passivated) as per Specification.

INCOMING:

3 Nos. 1600 Amps FP EDO Type ACB'50kA' With ON Indication Lamp with 2A SP MCB.

Digital flush type class-1.0 accuracy multifunction meter with RS485 showing V, A, PF, KVAR, KWH etc. current transformers of 1600/5A ratio, 10 VA Class 1.0 metering.

One (1) Set of Phase Indication & ON/OFF/TRIP Lamp with 2A SP MCB.

Control MCB'S, control terminals & wiring as required.

Under/ Over voltage, Master trip relays along with current transformers of 1600/5A ratio, 10 VA class-5P10 protection - 1 set

Suitable arrangement to receive incoming armored cables.

Ameter with ASS

Voltmeter with VSS

ON/OFF/TRIP Indication

Open/Close Push button

BUSBAR:

2000 Amps TP&N aluminum conductor bus bar (BPTM type Heat-shrinkable busbar insulation) supported by DMC / FRP insulators.

OUTGOINGS:

01 No. 630amps, 415V FP MCCB TM BASED '50kA' With ON Indication Lamp with 2A SP MCB.

01 Nos. 500amps, 415V FP MCCB TM BASED '50kA' With ON Indication Lamp with 2A SP MCB.

01 No. 250amps, 415V FP MCCB TM BASED '36kA' With ON Indication Lamp with 2A SP MCB.

01 No. 160amps, 415V FP MCCB TM BASED '25kA' With ON Indication Lamp with 2A SP MCB.

SUBHEAD :9 - ELV

CABLE TV WORKS

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

TV antenna socket outlet

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required

1 or 2 Module (75mmX75mm)

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required

Supplying and drawing folowing pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/recessed steel/PVC conduit as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

Telephone socket

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required

1 or 2 Module (75mmX75mm)

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required

Supplying and Laying of 1 pair CAT-6 cable

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required

Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required

(A) Supplying, installation, testing and commissioning of diesel engine driven main fire pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Diesel Driven Pump) (B) Horizontal type, multistage, centrifugal pump of cast of iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. (C) Suitable HP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant IS standard complete with auto starting mechanism, 12 /24 volts electric starting equipment, diesel tank, exhaust pipe extended upto 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required. (D) M.S fabricated, common base plate, coupling, coupling guard, foundation bolts etc. as required. (E) Suitable cement concrete foundation duly plastered and with anti vibration pads. 2850 Ipm at 56 m Head

(A) Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump) (B) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520 (C) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-’F’ insulation, conforming to IS-325. (D) M.S. fabricated common base plate, coupling, coupling guard, foundation bolts etc. as required. (E) Suitable cement concrete foundation duly plastered and with anti vibration pads. 900 Ipm at 35 m Head

Fabrication, supply, Insallation testing & commissioning of Electrical control panel of cubical construction, floor mounted type, fabricated out of 2mm thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, inter-connection with suitable size copper conductor cable/solid copper strip, having switchgears and accessories, mountings and internal wiring, earth terminals, numbering etc. complete in all respect, suitable for main fire pump, pressurisation pump & diesel pump set complete as per CPWD specification with following in coming and Outgoings, suitable for operation on 415V, 3 phase, 50HzAc Supply with enclosure protection class IP42 as required :

SYSTEM CONTROLLER Designing, Supply, Installation, Testing and commissioning of system controller to control operation of main electric fire pump, diesel pump, Pressurization pump, Terrace pump in sequence as per specification consisting of relays, timers. Sensors, annunciation window for fault indication complete as per specification

Providing, laying, testing & commissioning of ’C’ class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required. 150 mm. Dia

Providing, laying, testing & commissioning of ’C’ class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :

25 mm dia

32 mm dia

40 mm dia

50 mm dia

65 mm dia

80 mm dia

100 mm dia

125 mm dia

150 mm dia

200 mm dia (wall thickness = 6.3 mm)

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed stainless steel

Supplying and fixing single headed external hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed stainless steel

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :

50 mm Dia.

80 mm Dia.

100 mm Dia.

150 mm Dia.

Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 780 of following sizes as required :

200 mm dia

150 mm dia

80 mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :

50 mm dia

80 mm dia

150 mm dia

200 mm dia

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser,drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and painting with synthetic enamel paint of approved shade as required.

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required. 100 mm Dia NB

Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required.

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange.

80 mm dia

150 mm dia

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required :Stainless steel (Grade 304)

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25mm dia stop gunmetal valve & MS Pipe and socket. 40m

Supplying & fixing 63 mm dia gun metal short branch pipe with 20mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe Stainless steel (Grade 304)

Supplying and fixing of fire brigade connection of cast iron body with gun metal instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required:

2 Way - 100 mm dia M.S. pipe

4 Way - 150 mm dia M.S. pipe

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : Pendant Sprinkler

Supplying, installing, testing and commissioning of micro processor based intelligent addressable main fire alarm panel, central processing unit with the 8 loop capacity and capable of supporting upto 250 devices and detectors perloop, with on-board LCD display with min 16 lines of text, operating at 230 V 50 HZ - AC with inbuilt Battery Backup of a minimum 24 hours in normal conditionand 30 min in alarm condition, suitable provision for network connectivity,interfacing with third party equipment via a MODBUS/ OPC/ L-ON interfaceetc. conforming to IS 15908:2021, IS 2189: 2008, EN 54 & VDS / FM/ UL 864(10th edition) with 3 years replacement warranty FF-AFAS/CP

Supplying, installation, testing & commissioning sector panel suitable for following zones, complete with visual indications for short circuit fault, open circuit fault, fire condition and all other standard facilities as per IS:2189 with mimic diagram for all area/zone covered, complete with all connections, interconnections as required. 10 Zone

Supplying, installation, testing & commissioning of repeater panel with 320 character/ touch screen LCD display with inbuilt reset, acknowledge and silence switches complete as required.

Supplying, installing, testing and commissioning of intelligent addressablethermal/ heat detector with rate of rise cum fixed temperature thermistorcomplete with base as required, suitable for temperature variations from - 20°C to38 °C for fixed-heat and rate-of-rise type detectors whereas 0°C to 90°C for high heat type detectors, in built isolation mode, suitable for industrial/ kitchen/ boilerroom etc. with 3 years equipment replacement warranty, IS : 2175-1988reaffirmed 2000, IS 15908:2021 standards FF-AFAS/SD.

Supplying, installing, testing and commissioning of addressable optical smokedetector, single/twin LED’s with 360 degree view, suitable for low voltage 15 to32 V DC two wires supply, in-built locking mechanism to check the removal andpilferage of the detector, in built isolation mode, start up current 300μA and alarmcondition current shall be maximum 6.5 mA, operating temperature 0°C to 50°C,humidity 0-95% RH, IP 41, conforming to IS 2189: 2008, 11360_1985_Reff2020 EN 54 or UL Approved with 3 years equipment replacement warranty FFAFAS/ SD .

Supplying, installation, testing and commissioning of of fire alarm sounder with facility to make announcement, mounted in M.S. box (16 SWG) with hinged cover plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required.

Supplying, installation, testing and commissioning of manual call box in suitable enclosure with arrangement to raise the alarm when the glass is manually broken complete as required.

Supplying, installation, testing and commissioning of response indicator on surface/recessed MS box having two LED , metallic cover complete with all connections etc as required.

Supplying and laying of 2x1.5 sqmm fire survival armoured cable, 600/1000V rated with annealed copper conductor having glass mica fire barrier tape covered by an extruded layer of cross linkable ethylene propylene rubber (EPR) insulation and LSZH inner bedding, steel wire armouring & LSZH outer sheath complete as required.

Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB, MP3 player (including 6 zone button paging station) with seamless integration facility with main fire alarm panel for voice evacuation complete as required.

Supplying, installation, testing & commissioning of 1.5W/3W/6W ceiling speaker complete as required.

Supplying, installation, testing & commissioning of 1.5W/3W/6W metal box ceiling/wall speaker complete as required.

Supplying, installation, testing & commissioning of ceiling/wall mounted loud speaker, 3/1.5 Watt in ABS enclosure complete as required.

Supplying and drawing of cable fire retardant PVC insulated copper conductor cable in existing surafce/ recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required. Speaker cable single pair, 2 core 1.5 sqmm

Supplying and stacking of good earth at site including royalty and carriage upto 5 km complete (earth measured in stacks will be reduced by 20% for payment).

Providing Circular Cement Concrete pots of specified size, cast with cement concrete of nominal mix 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 6 mm nominal size), reinforced with 7 Nos ( 3 nos horizontal & 4 nos vertical “ U “ shape) M.S. wires of 3.5 mm dia as per design, including required form work, finishing with cement punning on exposed surface, curing for specified period and stacking in required rows & height, all complete as per direction of Officer-in-charge.

Top inside dia 35 cm, outer bottom dia 25 cm, total height 35 cm with wall thickness of 25.4 mm

Supplying and stacking at site dump manure from approved source, including carriage up to 1km (manure measured in stacks will be reduced by 8% for payment)

Same as good earth

Spreading of sludge, dump manure and/or good earth in required thickness as per direction of Officer-in-charge (Cost of sludge, dump manure and/or good earth to be paid seprately

Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge

Providing and displaying of Areca Palm plant, having ht. 90 cm to 1.20 m with 4 to 5 suckers, well developed, fresh and healthy with lush green foliage in 20 cm size of Earthen pot / Plastic pot & as per direction of the officer-in-charge.

Providing and displaying of Schefflera high colour having ht. 25 cm to 30 cm, well developed with fresh & healthy foliage in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.

Providing and displaying of Aglaonema Butterfly having ht.30 cm 10 to 12 fresh, healthy and attractive colorful leaves, well developed in 25 cm size Earthen pot/Plastic pot & as per direction of the officer-in-charge.

Providing and Displaying of Aglaonema Sam plant ht.30 cm well developed three in one, having 18 to 20 fresh, healthy and attractive colorful leaves in 35 cm size Earthen pot/Chali/Tray & as per direction of the officer-in-charge.

Providing and displaying of Aglaonema ernesto (three in one), having ht. 45 cm & above with 12 to 15 leaves, well developed, fresh and healthy in 25 cm size of Earthen pot/Plastic pot.& as per direction of the officer-in-charge.

Providing and displaying of Aglaonema modestum having ht. 23 cm to 30 cm with 3 to 4 suckers & 15 to 20 leaves, well developed, fresh and healthy in 25 cm size of Earthen pot/Plastic pot. & as per direction of the officer-in-charge.

Providing and displaying of Araucaria cookie having ht. 75 cm to 90 cm, straight, well developed, fresh and healthy with lush green leaves from bottom to top in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge

Providing and displaying of Araucaria cookie having ht. 1.80 m to 1.95 m, straight, well developed, fresh and healthy with lush green leaves from bottom to top in 30 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.

Providing and displaying of Brassia Variegated having ht. 30 cm, well developed with fresh and healthy foliage in 20 cm size of Earthen pot/ Plastic pot & as per direction of the officer-in-charge.

Providing and Displaying plants Allyssum white in full bloom well developed Fresh & healthy Plant in 20 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.

Providing and Displaying plants Missbranthemum in different colour well developed with fresh & healthy foliage in full bloom in 20 cm Earthen Pot/ Plastic Pot and as per direction of the officer-in-charge.

Providing and Displaying plants Nasturtium in different colour well developed with fresh & healthy foliage with full bloom in 20 cm Earthen Pot/Plastic Pot as per direction of the officer-in-charge..

Providing and Displaying plants Verbina in different colour having 30 to 45 cm ht., well developed with fresh & healthy foliage in bloom condition in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.

Providing and stacking of plant Mogra of height 25 to 30 cm., 2 to 3 branch in earthen pots of size 20 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge..

Providing and Displaying Budded Rose (H.T. variety) 3 to 4 healthy branch 30 cm and above ht. well developed with one and above flower plant in 20 cm Earthen Pot, as per direction of the officer-in-charge.

Providing and Displaying Chrysanthemum double variety, well developed, having 45 to 60 cm ht., with 6 and above flowers with half blooming condition, fresh and healthy with bamboo stacking in 25 cm Earthen Pot and as per direction of the officer-in-charge

Providing and Displaying Chrysanthemum single named variety in different colour well developed, having 45 to 60 cm ht., minimum 150 and above half bloom flowers well stacked with bamboo stick having three layer tiding by thread fresh and healthy foliage in 30 cm Earthen Pot and as per direction of the officer-in-charge.

Providing and Displaying Clianthus well developed, with fresh & healthy foliage in bloom 30 to 45 cm ht., with stacking in 25 cm Earthen Pot/ Plastic Pot and as per direction of the officer-in-charge.

Providing and Displaying Marigold jaffri dwarf in different colour well developed with fresh & healthy foliage with 12 to 15 flowers in full bloom specimen plant 23 to 30 cm ht. in 20 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.

Providing and Displaying Adenium Obesum grafted well developed with fresh & healthy 30 to 60 cm ht. in 25 cm size Earthen Pot/ Plastic Pot as per direction of the officer-in-charge.

Providing and Displaying Adenium Obesum well developed with fresh & healthy 4 to 5 branch 60 to 75 cm ht. in 40 cm size Earthen Pot/ Plastic Pot as per direction of the officer-in-charge.

Providing and Displaying Bamboo Buddha vally variety with umbrella shape having 120 to 135 ht. with fresh & healthy foliage well developed in 40 cm Cement pot multy branch, bushy as per direction of the officer-in-charge

Providing and Displaying Bamboo Buddha Valley with fresh & healthy 5 to 6 suckers 1.80 m to 2.10m ht umbrella type well developed in 50 cm Cement Pot as per direction of the officer-in-charge.

Providing and Displaying Cycus cirsnallis well developed with fresh & healthy 35 to 40 lush green leaves in 40 cm Cement Pot as per direction of the officer-in-charge.

Providing and Displaying Cycus revoluta specimen , having 45 to 50 fresh and healthy, leaves having 30cm to 35cm circumfrance of base stem well developed in 40 cm challi, as per direction of the officer-in-charge.

Providing and Displaying Ficus reginold well developed fresh & healthy foliage 60 to 75 cm spread 105 to 120 cm ht., Bushy in 35 cm Cement Pot as per direction of the officer-in-charge

Providing and Displaying Golden Bottle brush Topiary well developed with fresh & healthy foliage 5 to 6 big ball 115 to 180 cm ht in 40 cm Cement Pot as per direction of the officer-in-charge.

Providing and Displaying Topiary of Ficus Bush King well developed with fresh & healthy foliage from Top to Bottom with single piller 60 to 75 cm spread, 210 to 225 cm ht., in 35 cm Cement Tray/Cement Pot as per direction of the officer-in-charge.

Providing and Displaying Washingtonia filifera palm well developed 90 to 105 cm ht. having 5 to 6 straight fresh and healthy leaves in 35 cm Cement Pot as per direction of the officer-in-charge.

Providing and stacking of Duranta Golden, having ht.15 to 20 cm bushty shape with fresh and healthy leaves in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. FOR FRENCH GARDEN

Providing and stacking of Polyalthia longifolia (Ashok) of height 150-165 cm. in earthen pots of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Clerodendrum inerme of ht. 20 cm to 30 cm multi branched in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.

Providing and stacking of Polyalthia pendula (Ashok Pendula) of height 150-165 cm. in earthen pots of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Alternanthera species of height 15 cm to 20 cm, full of branches and foliage in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.

Providing and stacking of Ficus benjamina (green) of height 120-135 cm. with 6-8 branches and lush green foliage in g. bags of size 25 cm as per direction of the officer-in-charge.

Providing and Displaying Bougainvillea named variety, Sobhra, Thima, Marry palmar, Cherry Blossom etc. well developed with fresh & healthy bushy in full bloom 75 to 90 cm ht. in 40 cm Cement Pot as per direction of the officer-in-charge.

Supply and stacking of plant Cassia biflora of height 60-75 cm. with 4-5 branches in poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Jasmine grandiflorum (chameli) of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge.

Providing and stacking of Pinus longifolia (Pinus) of height 90-105 cm. in cement pots of size 35 cm as per direction of the officer-in-charge.

Providing and stacking of Bottle palm of ht. 150-180 cm bottom girth 20-25 cm well developed in big poly bags of size 25 cm as per direction of the officer-in-charge.

NON-SCHEDULED ITEM Providing PU (Polyurethane) finished coating over new wooden surfaces to achieve a smooth, durable, and glossy/matte texture with approved make and shade of PU coating, including thorough cleaning of the surface by removing dirt, scales, smoke, and grease, followed by sandpapering for an even finish. The process includes the application of multiple coats as required, ensuring proper drying time between coats, and achieving the desired finish. The cost includes scaffolding, taxes, and all necessary materials, labor, and equipment, all complete as per building specifications and as directed by the Engineer-in-charge.

Providing and fixing laminated (engineered wooden flooring) of suitable thickness 10-14 mm of suitable grade category product of approved made out of core high deMRty fibre board (HDF) &other component it treated for abrasion ,scratch ,moisture protection, flame protection,U.V resistant. backing under layer on min 2 mm thickness shall provide as sound absorbent and moisture protection layer .The Seamless impregenated decorative layer of specified size. design, colour and pettern, all bonded together under high temperature and pressure with eco-friendly resins specified by the manufacturer .The material shall be applicable warranty formaldehyde free, eco friendly, highly recommended for high traffic area and fully recyclable and matching shed and excluding quantity of skirting and profile.

Providing and Installation of acoustical wall panelling fabric finish hardened square edge, FR grade fabric (colour as approved by Egnineer in charge) wrapped soft fibre core (glass fibre) panel having metal framing, of size 600x2100x25mm having deMRty 100-120Kgs/ m3, weight 3.0kg/m2 NRC up to 0.9 installed by using impaling clip. Impaling clips are attached directly to the wall/frame work with the points extending outward. Then panels shall positioned and pressed into place.

Providing, supplying and installing at site Glass Reinforced Concrete (GRC) Jallis (Grills), made up of mainly White Cement (conforming to ASTM C 150), High Silica sand (conforming to ASTM c144), AR Glasfibre, Admixtuers (conforming to ASTM c260,ASTM c618), by using Vibration Cast Premix Process and as recommended by PCI (Precast Institute) USA, Manual 128 (edn4) or as per GRCA International specifications with design as per details provided in drawings and site requirements/ measurements and as per approved finish and color shade, with sealers and hardwares required, all in accordance with the manufacturer's specifications and conforming to Indian/ ASTM standards, along with submission of shop drawings for approval, complete in all respects.

Providing and fixing wooden panelling with framework in 50mm x 35mm approved seasoned hardwood section @ 600mm c/c both ways on the wall. 12mm Ply shall be fixed to the frame work and 4mm veneer fixed to the base layer and finished with Approved polish or as per drawings. Top of the panel to have the ply boxing ribs Approx side of 2400mm x 50mm ( thk will be 75mm) same will be finished with 4mm venner & malamine polishing Rate to be inclusive as approved by Engineer In-Charge.

Providing and fixing 12 mm thick frosted glass Urinal Partition with Dorma make of sizes menioned in approved drawing including necessary fittings etc complete as directed by Engineer In Charge. Size-(750x500)mm Deep

Providing & Fixing Glass body liquid soap dispenser(Make : Kohler, Model no.10712D-CP Jaquar cat no. ACN-CHR-1135N or equivalent make of Hindware etc.) with simple push lever fitted with liquid soap (one time) including cutting and making good the walls, wherever required.

Providing & fixing C.P. hand spray with lever control (health faucet) of ( Kohler cat no. 12927IN-CP / Hindware F160001 / Jaquar cat no. ALD-CHR-585 or approved equivalent) and flexible hose 1 m/1.2m long connection with C.P. holder for hand spray complete in all respects as per direction of Engineer-Incharge.

Providing and fixing SS COAT Hook of ( Kohler cat no. 14443-CP / Hindware cat no. F840007 / Jaquar cat no. AKP-35791P or approved equivalent)complete including consumable items, cutting and making good the walls where required.

Providing & Fixing of 15 mm dia angle valve of ( Kohler cat no. 80155IN-4-CP / Hindware cat no. F280004 / Jaquar cat no. FLR-5053N or approved equivalent) with C.P. brass wall flange with any other items complete including unplasticised PVC connection pipe with brass unions of 45cm length & 15mm nominal bore complete in all respect.

Providing and fixing push fit type WC pan connector ( Kohler Cat No.1036902 / Mcalpine Cat no. MAC - 1 or approved equivalent) with high quality polypropylene plastic with rubber sealing washer. The internal rubber gasket in EASI-fit pan connectors and extremely water tighsupplied spring loaded seal guard. single mould sealing fins made of flexible EVA body, including bush/adaptor. complete in all respect.

2 way Bib cock (Make: Hindware,Cat No :- F200004)

Providing and fixing CP Overhead shower with arm complete ( Kohler Cat No.99054IN-CP Shower arm & 37431IN-CP Overhead Shower, Hindware Cat No. Cat. No.: F190018 Shower arm & Cat. No.: F160061 Overhead Shower , Jaquar cat no. HA-479L300 Shower arm & OHS-497N,Overhead Shower/ or approved equivalent) including cutting and making good the walls where required.

Providing and fixing Wall Mounted C.P brass sink mixer with swinging type casted spout with wall flange. ( Kohler Cat No. K-37315IN-4-CP/ Hindware Cat No. F110020/ Jaquar cat no. FLR-5309N / or approved equivalent) complete to the satisfaction of Engineer in charge.

Providing & fixing of CP brass pressmatic self closing pillar tap (Hindware cat. No. F310001ACP/ Jaquar cat no.PRS-031 / or approved equivalent ) as per direction of Engineer-Incharge.

Providing and fixing 40mm dia SS Bottle Trap (Jaquar cat no. ALD-CHR-770 / Hindware F850016 or approved equivalent) and other ancillary fittings, cutting and making good the walls wherever required complete as per directions of Engineer-Incharge.

Providing and fixing 32mm dia SS Bottle Trap ( Kohler cat no. 7314IN-CP / Hindware F850015 / Jaquar cat no. ALD-CHR-769 or approved equivalent) and other ancillary fittings, cutting and making good the walls wherever required complete as per directions of Engineer-Incharge.

Providing & Fixing of Grab bar of ( Kohler cat no. 10701D-CP / Jaquar cat no. AKP-35701P or approved equivalent) non slipping grip as per standard specification of use in disabled toilet complete with brackets suitable for wall installation as per approved sample complete in all respect.

Providing & Fixing SS body paper towel dispenser Capacity 450-500Paper Towels) of ( Euronics, Cat no : EP01 / Jaquar cat no. PTD-SAP-DT0106CS or approved equivalent) complete with brackets fixed to wall with PVC rawl plug with CP brass screws complete in all respects, including cutting and making good the wall wherever required.

Providing & Fixing Aerosol Perfume Dispenser (Digital programming) of ( Euronics, Cat no : EA03 / AirWick or approved equivalent) fixed to wooden cleats with C.P brass screws, complete including cutting and making good the walls wherever required.

Providing & Fixing hand drier of best quality, to be operated with 230 volts, single phase, with fully hygienic condition, with all accessories of ( Kohler cat no. 5486T-0P / Jaquar cat no. HDR-SAP-M06ACS or approved equivalent) including cutting and making good the walls, wherever required.

Providing and fixing sound insulated pp piping system as per ON EN 1451-Part 1-6 & EN 12056 Part 1-5 with 3 layer pipe made of PP-C + PP-MV + PP-C in Blue Ral 5014 (halogen and calcium free) colour, push-fit type, food safe, having high impact and stiffness, offering sound levels of not more than 22 dBA at a flow rate of 4 l/s and having pipe ring stiffness as per 1S0/DIS 9969 and tightness as per EN 1277/B and C and DIN 19560, with all necessary fittings in blue colour, fitted with factory fitted lip ring . PP 110 mm dia Pipes

Providing and fixing sound insulated pp piping system as per ON EN 1451-Part 1-6 & EN 12056 Part 1-5 with 3 layer pipe made of PP-C + PP-MV + PP-C in Blue Ral 5014 (halogen and calcium free) colour, push-fit type, food safe, having high impact and stiffness, offering sound levels of not more than 22 dBA at a flow rate of 4 l/s and having pipe ring stiffness as per 1S0/DIS 9969 and tightness as per EN 1277/B and C and DIN 19560, with all necessary fittings in blue colour, fitted with factory fitted lip ring . (For Indirect waste/ Wash Basin/Urinal/Sink/Floor Drain )

PP 40 OD Pipes

PP 50 OD Pipes

Providing, fixing and testing of multitrap including jointing with solvent cement and making good the walls, floors etc., complete of nominal size.

110 mm inlet & 110 mm outlet Long ht

Providing and fixing floor drain (FD) with 50mm/40mm outlet and one 40mm inlet for waste, with SS grating (adjustable height), having 50mm water seal and in-built NRV (McAlpine mrfg3 ).

Providing and fixing SS Grating over Floor trap, floor Drain and multi trap 125 x 125

Providing and fixing push fit COP (Clean Out Plug) for cleaning with necessary bracket and support Make PKNG - POLOPLAST Germany. PP 110 mm dia

Providing and installing Air Admittance valves with required air flow rate, including submission of design data (McAlpine/STUDOR)

Airflow capacity upto 32 l/s ( Maxi Vent )

Providing & fixing MAXI FILTRA with active carbon filter (STUDOR). 100 / 110 mm dia

P/F Polo Ultra-V (UV protected) ML5 PP-r PE80 glass fibre compound 5 layer pipe in black colour classified according to DIN EN 21003 having linear expansion coefficient 0.038mm/mK with proprietiry Polo-Ecosan fittings complete, of food grade quality, jointing to be done by socket fussion including making chases in walls and making them good as required. (for use in toilets / internal and concealed applications) POLOPLAST - GERMANY.

Concealed work , including Cutting chases and making good the wall etc.

20x2.8 mm (OD)

25x3.5 mm (OD)

32x4.4 mm (OD)

P/F Polo Ultra-V (UV protected) ML5 PP-r PE80 glass fibre compound 5 layer pipe in black colour classified according to DIN EN 21003 having linear expansion coefficient 0.038mm/mK with proprietiry Polo-Ecosan fittings complete, of food grade quality,jointing to be done by socket fussion including painting with cement/other paint as required for external/exposed installation. (for use in shafts, basements, terrace all internal and external applications) POLOPLAST - GERMANY.

20x2.8 mm (OD)

25x3.5 mm (OD)

32x4.4 mm (OD)

40x5.5 mm (OD)

50x6.9 mm (OD)

63x8.6 mm (OD)

90 x 12.3 mm (OD)

110 x 15.1 mm (OD)

Providing, fixing, testing and commissioning Polo Ecosan Ball valve, with brass chrome plated ball, brass stem and PTFE (Teflon) seat PN 20, vales to be painted when installed exposed to sunlight. ECOSAN, Poloplast.

20mm nominal bore

25mm nominal bore

32mm nominal bore

40mm nominal bore

50mm nominal bore

Providing & Fixing of BUTTERFLY VALVE (MANUAL) with C I body SS disc nitrile. Sheet & O-ring & PN 16 pressure rating as specified.

65mm nominal bore

80mm nominal bore

100mm nominal bore

Providing, fixing, testing and commissioning moterise Ball valve of following sizes, for filling of overhead tanks complete with high & low level switchs & pressure switch to control the valve. The level controller shalll be installed in over head tank. The level switch will close the valve when water level is high & open the valve when level is low in the tank. The system should be complete in all respect with accessories, 220V AC / 24 V DC, IP 67 water level control unit, Control Panel, copper control wiring in weather proof casing etc.

50mm dia nominal bore

25mm dia nominal bore

Providing and fixing sound insulated pp piping system as per ON EN 1451-Part 1-6 & EN 12056 Part 1-5 with 3 layer pipe made of PP-C + PP-MV + PP-C in Blue Ral 5014 (halogen and calcium free) colour, push-fit type, food safe, having high impact and stiffness, offering sound levels of not more than 22 dBA at a flow rate of 4 l/s and having pipe ring stiffness as per 1S0/DIS 9969 and tightness as per EN 1277/B and C and DIN 19560, with all necessary fittings in blue colour, fitted with factory fitted lip ring . PP 160 mm dia Pipes

Providing and fixing push fit COP (Clean Out Plug) for cleaning with necessary bracket and support Make PKNG - POLOPLAST Germany.

PP 160 mm dia

Providing, fixing fabricated MS Heavy class Grating/Cover of 600 mm lenth Heavy class suitable for following size drain chennal. 400 mm wide drain & 15mm thick

4 x 25sqmm. + 1 x 6sqmm earth wire

7 W downlighter led light - (Wipro, Havells,philips,bajaj or Eqv)

18 W downlighter led light - (Wipro, Havells,philips,bajaj or Eqv)

25 W downlighter led light - (Wipro, Havells,philips,bajaj or Eqv)

30 W LED Ceiling light - (Wipro, Havells,philips,bajaj or Eqv)

20 W LED Tube light - (Wipro, Havells,philips,bajaj or Eqv)

9 W LED Bulk Head light - (Wipro, Havells,philips,bajaj or Eqv)

Propeller In-Line Exhaust fan 300mm sweep,70w-modelVentil Air DX (Havells, crompton or Eqv)

Supplying, installation, testing & commissioning of 90W LED Street lights on with all accessories as required.

Supply of 7 metre hot dip galvanised Single arm Octagonal pole (BOP-7030) with top dia 70mm, bottom dia 130mm & made of 3 mm thick sheet, base plate dimensions 200 x 200 x 12 mm(LXBXT) including suitable sizes of foundation bolt all complete with the help of suitable tools and plants, wiring of luminaires with all materials and construction of shallow foundation with M25 grade concrete considering safe soil bearing capacity of 10T/sq.mtrs as required and as per direction of Engineer-in-Charge.

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 100 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, double pole, (single phase and neutral), 230 volts, residual current circuit breaker (RCCB), having a sensitivity current 100 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.

SUPPLY OF CABLE

Supply of XLPE insulated and PVC sheathed power cable of 1.1 kV grade, 1.1 kV, multi core, aluminum,armored , underground, Conforming to IS 7098-2

3.5cx 300 sqmm

3.5 cx 150 sqmm

3.5 cx 95 sqmm

3.5 cx 70 sqmm

4c x 16 sqmm

Supplying, Installing, Testing & Commisioning cost of Main LT Panel all complete with all necessary items as per direction of Engineer-in-Charge.

Design, Fabrication, Supply, Erection,Testing and commisioning of Powder coated Indoor Type Panel fabricated out of 14 guage CRCA sheet steel in cubical, compartmentallised, free standing , dust and vermin proof, (degree of protection-IP54)with reinforcement of suitable size angle iron, channel, T -iron or flats as required. Cable gland plates shall be provided on top as well as bottom of the panels. Panels shall be treated with all anti-corrosive process before painting as per specification. Panels shall be suitable for 415V, 3-Phase, Four wire, 50 Hz supply complete with earth bus and lifting hooks as required in case of large panels.Approval shall be taken for each panel before fabrication. (All hardwares like nuts and bolts used shall be Galvanized and Zinc passivated) as per Specification.

INCOMING:01

1 Nos. 630Amps FP MCCB 50kA With Thermal Magnetic release for O/C, S/C & Earth Fault Protection.

Digital flush type class-1.0 accuracy multifunction meter with RS485 showing V, A, PF, KVAR, KWH etc. current transformers of 630/5A ratio, 10 VA Class 1.0 metering.

One (1) Set of Phase Indication & ON/OFF/TRIP Lamp with 2A SP MCB.

Control MCB'S, control terminals & wiring as required.

Under/ Over voltage, Master trip relays along with current transformers of 630/5A ratio, 10 VA class-5P10 protection - 1 set

Suitable arrangement to receive incoming armored cables.

Ameter with ASS

Voltmeter with VSS

ON/OFF/TRIP Indication

Open/Close Push button

BUSBAR:

800 Amps TP&N aluminum conductor bus bar (BPTM type Heat-shrinkable busbar insulation) supported by DMC / FRP insulators.

OUTGOINGS:

03 Nos. 160amps, 415V FP MCCB TM BASED '25kA' With ON Indication Lamp with 2A SP MCB.

06 Nos. 125amps, 415V FP MCCB TM BASED '25kA' With ON Indication Lamp with 2A SP MCB.

02 Nos. 63amps, 415V FP MCCB TM BASED '16kA' With ON Indication Lamp with 2A SP MCB.

Supplying, Installing, Testing & Commisioning cost of HVAC Panel all complete with all necessary items as per direction of Engineer-in-Charge.

Design, Fabrication, Supply, Erection,Testing and commisioning of Powder coated Indoor Type Panel fabricated out of 14 guage CRCA sheet steel in cubical, compartmentallised, free standing , dust and vermin proof, (degree of protection-IP54)with reinforcement of suitable size angle iron, channel, T -iron or flats as required. Cable gland plates shall be provided on top as well as bottom of the panels. Panels shall be treated with all anti-corrosive process before painting as per specification. Panels shall be suitable for 415V, 3-Phase, Four wire, 50 Hz supply complete with earth bus and lifting hooks as required in case of large panels.Approval shall be taken for each panel before fabrication. (All hardwares like nuts and bolts used shall be Galvanized and Zinc passivated) as per Specification.

INCOMING:01

1 Nos. 160Amps FP MCCB 36kA With Thermal Magnetic release for O/C, S/C & Earth Fault Protection.

Digital flush type class-1.0 accuracy multifunction meter with RS485 showing V, A, PF, KVAR, KWH etc. current transformers of 160/5A ratio, 10 VA Class 1.0 metering.

One (1) Set of Phase Indication & ON/OFF/TRIP Lamp with 2A SP MCB.

Control MCB'S, control terminals & wiring as required.

Under/ Over voltage, Master trip relays along with current transformers of 160/5A ratio, 10 VA class-5P10 protection - 1 set

Suitable arrangement to receive incoming armored cables.

Ameter with ASS

Voltmeter with VSS

ON/OFF/TRIP Indication

Open/Close Push button

BUSBAR:

200 Amps TP&N aluminum conductor bus bar (BPTM type Heat-shrinkable busbar insulation) supported by DMC / FRP insulators.

OUTGOINGS:

06 Nos. 63amps, 415V FP MCB '10kA' Class C

Supplying, Installing, Testing & Commisioning cost of Utility Panel all complete with all necessary items as per direction of Engineer-in-Charge.

Incomer

CAPACITOR PANEL -350 kVAr

Incomer

6 A MCB, with LED indicators for phase and ON/OFF/TRIP-1 set

800 Amps ,50KA, 500 V MCCB isolator -1 each

Digital Multifuction Meter ( AVF )-1 each

630/5A, Cl- 1 CT for metering 15VA-3 each

Off Delay Timer-1 each

8" Fan With Filter-1 each

aux contactor -1 each

Busbar

1000 Amps TP&N aluminum conductor bus bar (BPTM type Heat-shrinkable busbar insulation) supported by DMC / FRP insulators.

Outgoing

6 A MCB, with LED indicators for phase and ON/OFF/TRIP-7 set

250A TP MCCB 25KA with Thermal Magnetic Release+ Spreader+ ROH 2 each

160A TP MCCB 25KA with Thermal Magnetic Release+ Spreader+ ROH 3 each

63 A TP MCCB 25KA with Thermal Magnetic Release+ Spreader+ ROH 3 each

40 A TP MCCB 25KA with Thermal Magnetic Release+ Spreader+ ROH 2 each

100 KVAR capacitor duty TP contactor -1 each

50 KVAR capacitor duty TP contactor -3 each

25 KVAR capacitor duty TP contactor -3 each

12.5 KVAR capacitor duty TP contactor -2 each

necessary indicators for on/off /hooter and auto/manual switch shall be provided

100 KVAR capacitor -1each

50 KVAR capacitor -3 each

25 KVAR capacitor -3 each

12.5 KVAR capacitor -2 each

No load compensation of transformer shall be provided with capacitor

APFCR -9 stage relay with RS485 connectivity

Supplying, Installing, Testing & Commisioning cost of APFC Panel all complete with all necessary items as per direction of Engineer-in-Charge.

Supply, installation, testing & commissioning of 32 Port analog extension , 8 port digital extension, 4 P& T lines , digital IP EPABX system in simplex mode and all cards hot swappable and expandable upto 64 ports and with all features as per technical specifications along with following and built in least cost routing, snmp based system administration, supports H-320 protocol EPABX, support dect connectivity- digital cordless extention, lan connectivity, music on hold for all users and accessories as required with Battery backup and Charger complete as required

Supply, Installation, Testing and Commissioning of Digital Key Phones

Supply, Installation, Testing and Commissioning of Analog phone

Supply, Installation, Testing and Commissioning of Following Pair MDF Box

SUBHEAD :11 - CCTV & DATA

Supply , Installation, Testing and Commissioing of 1/2.8 '' 2.1MP CMOS Starlight Sensor Bullet Camera with effective 1945(H) X 1109(V) pixels, Fixed lens 4 mm , Video Compression H.265, H.264,M-JPEG , Color: 0.03Lux)/F2.0, 0 Lux (IR On), Smart IR Distance 80ft, True WDR 120dB , Auto Iris , Dual Streaming , Frame rate 30 FPS on 1080p resolution , Smart advanced video Compression, Electronic Shutter Speed Auto / Manual (1/15 ~ 1/32000), Anti-Flicker, Slow Shutter (1/2,1/3,1/5,1/6, 1/7.5,1/10), 3D DNR , Support SD card , Audio Input & Output ,Alram Input & output ,Polygon motion detection , Privacy masking, ONVIF ,Ethernet port 10/100 Mbps, ,12DC, PoE, Metal body, IP66 protection Certificate UL, BIS, EN , FCC & RoHS Certification. 3 Years Standard Warranty

Supply , Installation, Testing and Commissioing of Professional Video Control Operations Management Playback Recording Single Server Multiple Client Video Surveillance 64 bit Software with Single channel camera licensce with unlimited clients supporting 5000+ Camera models and 15000 devices at SDK level , Onvif S supported, edge base recording , advance maps, advance event and action manager with streaming server supporting optional edge or server level analytics at extra charges and optional facial recognition with 2 year standard support pack included Make: Milestone/ Wavesys/ Genetec

Supply , Installation, Testing and Commissioing of Tower Mount upto 128 Camera Channel Recording & Monitoring NVR Single Socket Intel Xeon Scalable Processor, (6) DIMM slots, (4) 3.5" internal Drive Slots, 1 NVMe M.2, 2 PCI-E 3.0 x16, 1 PCI-E 3.0 x8 (in x8), (2) GbE ports, Aspeed AST2500 BMC, 500W Power Supply. Intel Xeon Bronze 3206R 8 core Processor (11M Cache, 1.90 Ghz), 64GB DDR4 RDIMM, PCI 128 TB NVMe M.2, Nvidia Quadro T400 8GB DDR6 Graphic Card, Win. 10 professional 64 bit. VCOMPRS Software Channel Prices extra Make: Milestone/ Wavesys/ HP/ Dell

Supply , Installation, Testing and Commissioing of 32" Monitor Bezel Thin 1080p HD LED Screen for live view and replay of recorded View with mounting stand & HDMI cable

Supply, Installation, Testing and Commisioning of Twin RJ45 Connectors IO Box.

Supply and fixing single line diagram, schematic diagrams etc. of A1 size on suitable Aluminium sheet including lamination etc. as required complete on wall.

Supply and fixing glass framed shock treatment chart.900mm x 600mm high, printed preferably in three languages i.e. Hindi, English & local language;

Providing & Fixing of Electrical insulating rubber mats as per PWD specification for electrical Works, ISI marked confirming to IS: 15652 / 2006 with one side anti skid abberation marks and pasting the mat with synthetic rubber adhesive as required

Standard first aid box - prescribed by St.John Ambulance brigade or India Red Cross shall be provided (First aid box should be of 18 gauge M.S sheet of size 14" x 17" x 5"):-

Supply of MS Items like Insert plates, angle iron, flats, supports, channels, etc.for cable trays/trenches/customized trays and wherever required with 2 coats yellow synchromate primer and 2 coats of enamel paint.

7 W led mirror light - (Wipro, Havells,philips,bajaj or Eqv)

Transformer Section: 11/0.433 KV Class, OCTC, AN, ECBC, CRT Dry Type Transformer LT Section: 1600 A, Four Pole, Manual Drawout type ACB with 50 kA, Microprocessor based O/L, S/C & E/F relay protection

KIRLOSKAR 1250 KVA DG set with Engine Model 12K4300-E1 12 Cylinder developing 1482 BHP coupled with KG-make Alternator Water Cooled, Acoustic Enclosure &Base frame. And 990 Litre Fuel Day Tank with necessary piping. AMF Panel (with Double ACB Breaker)

Manufacturing & supplying of Curtains Channel, as per shape and design as per the following and as per drawing,,all complete job as per approved designed drawings & directions of engineer in charge.

Providing and fixing approved brand and manufacture SS 304 grade Tower Bolt Size - 10", SAP code 9117718 or equivalent fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Proving and Fixing 12" SS 304 Door Handle of approved Make : Dorma/Hattich, all complete job

Providing and Fixing Cylindrical Lock of approved Godrej/Dorset all complete job. (Plumbing Shaft)

Providing and fixing Electronic Hotel mortise lock with RFID Mifare reader in satin chrome finish compatible with Electronic hotel lock software.

Providing and Fixing Triolock Dead Bolt suitable for Double Leaf Door Shutter of approved Make Godrej/Dorma, all complete job as per direction of E/I

Providing and fixing ITS 96, concealed cam action door closer with G 96 N slide channel arm with standard spindle, including cushioned limit stay. Spring size EN 2-4 as per EN 1154 and CE marked. Silver finish. Non-handed version.

Roller Blinds : Supply and Installation of Black out Roller Blinds - (For Windows) Supply & Installation of manually operated roller blinds as per approved style and shade. Blinds to be overlapped. Technical Specifications:100% Opaque Composition:100% Polyster Thickness:0.6Mm Width(m):230Cms Mesh Weight(g/m):390Gsm Breaking Strength: Warp>=1300WEFT>=1200 Tear Strength: Warp>=20WEFT>=20 Color Fastness:ISO105B02,Grade B Anti Ultraviolet:100% Fire Classification:NFPA701-2004TM#1 Coating: Blackout 3 Pass foam coating EPI / PPI: 176/164,Made by Vista or equivalent. all complete job as per approved designed drawings & directions of engineer in charge.

Providing and fixing Wall Paper over existing ply or wall surface . , wall paper fixing on the ply surface with adhesive material. The wall paper as per the approved shade,,all complete job as per approved designed drawings & directions of engineer in charge.

Providing & fixing TV Panel Unit on wall suface with 50 x 50 mm wooden batta frame work on surface coverd 18 mm thick BWR Ply, Anti termite paint or fire proof paint spread on the surface of the ply touching the wall , inside the tv panel frame paisted 1 mm thick laminate with adhesive material one side paisted and pressed with adhesive to give a uniform and smooth surface, the surface of the ply covered with veener & polish for the veener and laminate as per the approved shade & design,all complete job as per approved designed drawings & directions of engineer in charge.(For Suite Room Drawing Room and Offoce Area)

Manufacturing & fixing TV ledge of Size: Maximum size(3150 x 450 mm) made with 18 mm thick 710 BWP Ply with PU polish outside & laminate insides as per drawing or instruction by site incharge: (

Providing and fixing 50x50 mm HDHMR molding on the wall surface or in any one direction, fixed and finish with nails in the position, as shown in the drawings complete,all complete job as per approved designed drawings & directions of engineer in charge.

Providing & fixing Paneling with PU paint over Ply, the 18 mm thick BWP ply fixed on the wall with screws & gitti, and Anti termite paint or fire proof paint spread on the surface of the ply touching the wall, fixing of 6 nos diffrent sizes ractangular in shape 18 mm HDHMR border profile as shown in the 3D view, HDHMR boder profile and under portion finish with PU paint, as per approved by architect or as per the approved shade and design. ( For CM/GOV Suite Room)

Providing & fixing Divider panelling made of 25x25 mm Bars PVDF finish with insert panels of 6 mm frosted glass, as per shown in the drawing or instructed by client,all complete job as per approved designed drawings & directions of engineer in charge. ( For CM and GOV Suite)

Providing & laying of 20mm thick Nylon Carpet for gymnesium floor, made up of euronics nylon or Mohawk industries and fixing on the existing tile floor with adhesive material as per approved by the architect,all complete job as per approved designed drawings & directions of engineer in charge.

Providing and fixing HDHMR Designing Jali partition, finish with PU Paint as per shown in the drawing or as per approved by archutect. The rates fixing complete in all respect and design approved by the client.( CM Office)

supply and Placing of 20LTR plastic bucket of approved best quality and make Milton/Cello/Polyset

sypply of 2 ltr capacity plastic mug of approved best quality and make Milton/Cello/Polyset

supply of doormate of approved best quality and make .

supply of bath stool of approved best quality and make Milton/Cello/Polyset

supply of wooden hanger of approved best quality and make.

Providing and Fixing Wall clock with Silent Sweep Technology of Size: 30 cm X 30 Cm of reputed Make: Titan/Seiko

Providing and Placing Freestanding Wooden Stand for Drying or Hanging Wet Cloth

Providing and Placing Stainless Steel Pedal Dust Bin with Lid of approved Best Quality

Providing and Placing Flipflop Slippers, Casual and comfortable for Everyday Use of approved Make Relaxo/Lakhani/Bata

Supplying & placing side table of size 600x600mm as per aproved designed drawings duly made with Teak Wood, Ply, Vineer withPU polish all complete job.

Manufacturing, supplying & placing single bed of size 900x1950mm duly made with Wooden Frame, 18mm thick 710 ply ,4mm thick veneer with PU Polish & teak wood leg as per approved designed drawing including cost of 4" thick mattress of approved make sleepwell/kurlon/Godrej, all complete as per direction of Engineer in charge.

Manufacturing, supplying and fixing Wardrobe of 600 mm depth with 5 compartment and 5 openable door fixed on to 18mm BB box , Cupboard to have 100 mm recessed skirting including TW beadings handles, locks fixed to the sliding shutter with all exposed visible surface to be covered with PU semi gloss finish to be matched with Wall Paint., and all internal surfaces to be finished with PU laminate, adhesives, nails screws etc., complete. All hardware to be soft close the sliding channles will be quodro and handles 12'' long void above wardrobe shall be covered with the ply board and veneer same as wardrobe shutter

Bed Side table Code CMST-3 (Size: 500x400x500 mm ),As per approved Design/Drawing

King Size Bed Code BED-4 (1800 x 1980 x 450 mm),As per approved Design/Drawing

Ottoman size code CMOTT-3(1500 x450 x 450 mm) , As per approved Design/Drawing

Cabinet of size ( 3650 x 1200 mm as per site requirement), as per approved Design/Drawing

Cabinet of size (2000 x 750 mm or as per site requirement), As per approved Design/Drawing

3 Seater Sofa code CMSO-2, As per approved Design/Drawing

Single seater Sofa code CMSO-1, As per approved Design/Drawing

Full Back Lounge Chair Code CMC-3, As per approved Design/Drawing

Double seater Sofa Chair code CMSO-4, As per approved Design/Drawing

Manufacturing & supplying of 2 seater Bench of size (1600 x 600 mm) attached with wall, solid wood frame with polyfi form filling of density of form should be maintain between 32&23, sofa finishes should be done with velvet fabric, wooden surface finished with veener and PU polish , as per shape and design as per the following and as per drawing:

Supplying & placing King size Mattress, 6" thick of approved approved make sleepwell esteem/Kurlon/Godrej as per direction of E/I (including CM Office)

Manufacturing & supplying of Ottoman size (1500 x450 mm) with Gold PVD Legs, fabric covering as per shape and design as per the following and as per approved drawing:

Manufacturing & supplying of a set of Dinning Table with four chairs Code SUT-2 of size (1250x600x750 mm), the italian finish on the top of the table wood finish chair shall be made with comfortable arm chair with fabric with teak wood legs as per shape & designed approved by EI.

Manufacturing & supplying of Center Table Code SUCT-1 of size 1200 mm X600mm in length, the table made up of HDHMR board over all side with PU paint and Italian marble finishes on the top of the table, another high table base finish with HDHMR board with PU paint, as per approved by the architect or as per shape and design as per the following and as per drawing:

Manufacturing & supplying of 18mm thick MR Ply Bedroom Side table code CMOST-3 (450x600x500 mm) , having 2 nos sliding drawer, with design handle as shown in the drawing, finish with PU paint, made up of HDHMR board and hard wood designed leg as shown in the drawing, as per shape and design or as per approved by the architect. all hardware to be soft close.

Manufacturing & supplying of Chair Code CMOC-1, comfirtable chair with fabric with metal legs with wheels, as per shape and design as per the following and as per drawing:

Manufacturing & supplying of Chair code CMOC-2, Solid wood frame with polyfi form filling of density of form should be maintain between 32&23, sofa chair top finishes should be done with Velvet Fabric, as per shape and design as per the following and as per drawing:

DINING ARMCHAIR Dining Armchair with Aluminium frame powder coated, Woven withSynthetic Rope. Cushions in Agora make 100% solution dyed acrylic fabric with PU foam. (Dimensions: W61 x D76 x H86 cms)

DINING ARMCHAIR (FABRIC) Dining Armchair with Aluminium frame powder coated, Woven withSynthetic Rope. Cushions in Agora make 100% solution dyed acrylic fabric with PU foam. (Dimensions: W61 x D76 x H86 cms)

CENTER POLE UMBRELLA(DIMENSIONS- 10FT SQUARE)

Buffet counter 8000X650X750 Stainless steel frame with 10mm toughened glass top

Supplying & Placing Modular table in completely knock down conditions that is to be assembled at site. The worktop shall have the size 1500mm/600mm X 1500mm/600mm made up of back to back 25mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The top profile shall be in curvilinear shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. Pullout keyboard trey shall be provided of metal base having size 470mm X 286mm. The trey shall be operated on keyboard channel. The workstation shall have panel based partition of 60mm thick with 1200/1650 mm height and provided at front of the user as well as both side of the user. The framework shall be made of Aluminium alloy extruded profiles. The partition shall have the assembly of top trim, top bar, mid bar, side pole, squirting, raceway and side beading. The entire Aluminium parts shall be pretreated and duly powder coated of 40-50µ dry film thick.

All these frame work sections shall be fitted to each other by fasteners of 2mm thick which is properly zinc coated for corrosion resistant. Raceway shall be provided of Aluminium of size 118mm height below the work top as per requirement for inlaying of electrical management and carrying the wire horizontally. The exposed vertical and horizontal faces of the frames shall be snap fitted with side beading and top trims respectively. The top and bottom tile shall be provide at front of the user and below the wroktop respectively. The beading shall have extruded profile and made of PVC. The trims shall be made of aluminium extrusions of size 60mm with 1.5mm thick. The partition shall have concealed wire management capabilities for responsive and safe operations of power, telecommunications and data (LAN) and has separate components for electrical, data and telephone cables having adequate capability of both the vertical and horizontal wire movements. Slots/cutouts shall be given on raceways to fix all electrical and data points. Zinc coated small top support brackets shall be fixed to the partition frame.

56 Seating As per Layout Providing and supplying conference table in completely knock down conditions that is to be assembled at site. The worktop shall be made up of 25mm thick Medium Density Fibre-board with approved veneer laminate. The top shall be supplied with thin layer of polyurethane polish and duly biffed for shining finish. Flip-up box shall be enclosed at table top that houses telephone cable, data and power connection discretely. The top shall be supported on gable end. The end wall of the table on the side shall be topped by gable end. It should be made up of 25mm thick medium density fibre-board with venner laminates. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It should be 18mm thick commercial ply veneer laminate. There shall be buffers provided at the base to avoid scratches on the floor. The complete structure shall be supplied with approved veneer laminate, . The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. of approved Make Geeken/Godrej/Durian.

Providing and Placing Console Unit of Length: 48inch and Height 32 inch , duly made with second Class Teak wood Frame with Leg and Top with 18 mm thick Ply/HDHMR Board finished with PU Polish all complete as per approved Design and Drawing. (For Corridor)

Providing and Fixing S S Metal Profile of approved Size with Italian Stone as per approved Flooring Drawing

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 125 mm Dia.

Supplying & Fixing of forged brass ball valve as per IS 778 (Pressure class PN 16) with flanges, nut bolts, gaskets and necessary pad locking arrangement complete as per the technical specifications and drawings. 25 mm dia NB

Supplying and Fixing of C.I. flanged Foot valve with strainer complete in all respects, as required.

150 mm Dia NB

200 mm Dia NB

Supplying & Fixing of Gunmetal Bourdon Type pressure gauge with gunmetal isolation ball valve tapping and connecting pipe and nipple for pump sets, complete in all respects, as per Technical Specifications and Drawings, suitable for working pressure of 250 PSI. Cost shall be inclusive of providing any short pieces, nipples, elbows etc as required.

Air Release Valve

Supplying and fixing of Air release valve 25 NB, Gunmetal Cap release Type - Valve with ball valve & accessories.

Providing & Fixing weather proof lockable cabinet of size not less than 0.75x0.6x0.25 mtr made out of 16 gauge MS powder coated sheet of fully welded construction having central opening and 3 mm thick glazed glass doors (Two nos.) suitably marked on the outside with the letters "FIRE HOSE" including necessary locking arrangement and shall be painted with one coat of primer and two coats of synthetic enamel paint of approved shade complete as required.

Providing of ABC powder type( stored pressure) Fire Extinguisher 4 KG. Capacity,ISI marked, IS 15683 for class 4 A &89 B type of fire field with MAP -90 complete in all respect.(Manual)

Providing of CO2 type( stored pressure) Fire Extinguisher 4.5 KG. Capacity,ISI marked, IS 15222 with all accessories complete in all respect.(Manual)

Providing of Chemical type fire extinguisher (K-Type) 6 kg capacity ISI marked IS 13849 with 1 mtr hose & pvc horn complete in all respect.

Supplying & Fixing, Fire Buckets 9 litres capacity round bottom sand buckets along with bucket stand (Wall hanging type) as per local fire officer's standards and located at ground floor. (4 BUCKETS = 1 SET).

Supplying and installing in position the following type of sign boards made out of 3mm thick "Opaque" PVC foam board with computer cut, PVC non-reflective self-adhesive vinyl painted foam board, complete with mirror fasteners

Fire extinguisher - with symbol. Size of 6" x 6".

Manual call point symbol. Size of 6" x 8".

Fire alarm panel - Size of 6" x 8".

In case of fire Do not use Lift Use Stair with symbol Size of 10" x 12".

Fire Hydrant & Hose reel - with symbol. Size of 6" x 8".

Refuge area. Size of 8" x 8".

Arrow Downwards + Running man + Emergency Exit with symbol. Size of 6" x 16".

Passanger Lift-17 Passengers-10 Stoppage

Wood Artwork and Paintings-Handicraft Weight- 500 gram Glass Type- Glass Thickness of board-6 inch Type of Painting-Sand Painting Frame Type-Framed Material-Wood Width-153 millimeter Length-457 millimeter Height-381 millimeter

Crafted on premium handmade paper, this piece is a testament to skilled craftsmanship and cultural storytelling. Ideal for framing or as a unique addition to your art collection, it brings a touch of India’s artistic legacy to any space. LENGTH 22 inch BREADTH 15 INCH

Product Dimensions 26L x 72W Cen meters Orienta on Landscape Frame Type Framed Colour Mul color Brand Generic Net Quan ty 1.0 count

Product Dimensions 26L x 72W Cen meters Orienta on Landscape Frame Type Framed Colour Mul color Brand Generic Net Quan ty 1.0 count

Raja Rajeswari, Lakshmi and Saraswati – Mysore Painting (30″ x 24″)

“Providing and executing high-quality Jharkhand tribal folk mural artwork on the prepared wall surface using premium acrylic colours, traditional motifs, fine detailing, and a UV resistant matte protective coat, all completed as per the approved concept and artist craftsmanship.” (2000 sqft @ 2400rs/sqft)

Materials: Irish heritage wool from Kerry Woollen mills, lamb lockets, merino fibers, embroidery threads, time and love, shadow box frame The measurements of this art is 8x8inches in a 9x9 frame.

Materials: Irish heritage wool from Kerry Woollen mills, lamb lockets, merino fibers, embroidery threads, time and love, shadow box frame The measurements of this art is 8x8inches in a 9x9 frame.

Materials: Irish heritage wool from Kerry Woollen mills, lamb lockets, merino fibers, embroidery threads, time and love, shadow box frame The measurements of this art is 8x8inches in a 9x9 frame.

Materials: Irish heritage wool from Kerry Woollen mills, lamb lockets, merino fibers, embroidery threads, time and love, shadow box frame The measurements of this art is 8x8inches in a 9x9 frame.

Madhubhani - Painting GeM Madhubani Painting of actual Length (in cm) 47 and actual Width (in cm) 37 With Framing

Madhubhani - Painting GeM Madhubani Painting of actual Length (in cm) 47 and actual Width (in cm) 23 With Framing

Madhubhani - Painting GeM Madhubani Painting of actual Length (in cm) 55 and actual Width (in cm) 55 With Framing

Krutik Dramatic Waterfall Wall Art, Misty Rocky Cliffs Canvas Painting with Red Tree and Golden Grass, 48x60 Inches

Electrolux refrigiator Model no - EC060 single door 47 ltr capicity direct cool Colour steel finish

Whirlpool rerigiator Model no - 215 ice magic prm 200 ltr Single door wine colour

Sony led 55inches Model no - X7002E sony bravia ulta hd 4k

Sony led 32inches Model no - 32R303E sony bravia hd ready

Morphy richards kettel Model no - impresso 1ltr steel black

Panasonic telephone instument Model no- tcs60 corded land line phone

Philips emergency light Model no- ojas rechargable

RFID DOOR LOCK Specification: RFID Door Lock TES-301SB  Model No.: TES-301SB  Size： 240*76mm  Features: Working Voltage: DC3.5-6.5v, (segments 4 alkaline battery) TM Card & mechanical key.  Battery Life: Above 18000times in normal99  Quiescent Current <20μA  Dynamic Current <1500mA  Temperature Range: -40-+85°C  Work humidity: 15-95 %RH  Card Distance: 5 mm Read  card time: <0.2s  Card Type: TM Card

CARD ENCODER Specifications: Card Encoder  Size: 10*14.5*3mm  Features: Function for program any kinds of Temic5557 Card be connected with computer via software;  Port: USB port  Card Frequency: 125 KHz;  Material: plastic

TES-ELOCK SOFTWARE Hotel Lock Management System  Reports – Card Report , Guest Report  Staff Card  Guest Card

ENERGY SAVING SWITCH: Model No.: TES-SW01G – PT Size: 85*85*42mm Working voltage: Alternating Current 180V-280V Switch Type: TM Card Maximum current: 40A Maximum power: 6000W Delay time:8-15 seconds

TM CARD Size: 85*55mm Features: Card Type: TM Card; CardFrequency:125KHz CardData: 330Bits;

DATA COLLECTOR We hold expertise in providing a wide series of Data Collector for hotel locks. Our products are extensively used in the market due to their low maintenance and longer services life. DATA COLLECTOR FOR HOTEL LOCKS helps you keep you record of your property usage. Best thing in Hotel Locks System

DIGITAL LOCKER 1. Product Description, Home digital safe, household safe, security safe box, electronic safety box, Ideal for home use, to keep valuable items, such jewellery, digital equipment, property certificate, important files etc. Indication for lower-battery power, about the time to change the batteries. 4×”AA” (1.5V) batteries offered for free. LED light flashes indicate different meanings.

HAND DRYER Product Description: Product Name: TES-HD002 Power rating: 1800W Tamp. of wind: 60⁰C ± 20⁰C Velocity of wind: 12m/sec Voltage rating: 220~ Acting distance: >50mm Delay time: < 5sec.

REFRI. Model: TES-4001BS Cooling Method: Absorption technologies (Without Compressor), ammonia water circle Dimensions(mm) : L440*W400*H550 Colour -Black Voltage -65W, AC：220V/60HZ、110V/60HZ，DC12V Energy Consumption: 0.9kwh/24h Validity Capacity : 40L Storage Temperature : 0~8℃ Door: Plastic door

KETTLE 1)“STRIX” control, lock open lid. 2) Double wall stainless steel body 3) Maximum capacity: 1.2L 4) Power consumption: 220V~240V AC 1500W; 50Hz~60Hz. 5) Auto shut off, dry boil protection 6) Boiling time: 3.5~4.5minutes (room temperature) 7) Large spout, optimized filter and steam vent, easy to clean 8) With plastic kettle tray or without tray.

DIGITAL DOOR PLATE Model: TES-DP001CR  Working voltage: 220V/110V/12V  Service lifespan: up to 1,000,000 touch times  Working temperature: -10 to 60°C  Heavy current controlled by L-line  Material: fire-proofing ABS  Frame: tempered glass frame shell  Colors: black and white  Standard size of domestic wall switches  Lower mechanical tear and wear  Many exquisite pictures are available  With LED backlight  Whole screen touch technology  Suitable for star hotel, hospital etc.

Providing and fixing Signage made of SS 304 (brush finish) 1mm thick color coated SS sheet for Logo and letters with raising (letter depth of 50mm). Including all fittings, accessories, fixtures, fabrication.The signage will be front illuminated / hollow illuminated either back or front of the signage to be made of 4 mm thick acrylic. using 7 year warrantee of 3M/Avery/LG cast vinyl for desired colour with OSRAM / PHILIPS/ GE IP 67 grade approved LED's along with OSRAM / PHILIPS/ GE SMPS fixed on the wall with necessary fixtures. Signage make 247SIGN/ VISTA Systems/ Glo-lite.

Providing and fixing Signage made of SS 304 (brush finish) 1mm thick.sheet for Logo and letters with raising (letter depth of 25mm). Including all fittings, accessories, fixtures, fabrication.The signage will be front illuminated / hollow illuminated either back or front of the signage to be made of 4 mm thick acrylic. 3M/Avery/LG cast vinyl for desired colour with OSRAM / PHILIPS/ GE IP 67 grade approved LED's along with SMPS OSRAM / PHILIPS/ GE fixed on the wallwith necessary fixtures. Signage make 247SIGN/ VISTA Systems/ Glo-lite.

Supply & installation Signage Made Of Base 3 MM Beton silver/ Beton white/ Swiss snow finish ACP panel Box having 6063 Alloy profiles to house the edge of ACP with in groove. Profile size 17 X 38 mm @edges and to be eprotuded by 5mm x 3mm beyond side surface from front side to make teh surface appeared recessed. Powder coated / Anodised as per approved shade. Fascia 3 mm acrylic sheet to be Stuck on base ACP Sheet in staggered manner before fixing of signage then Content CNC Cut Acrylic 2 mm thick fixed on signage facia. signage to be mounted using clamps at backside of profile. teh sheets and content to be duly CNC cut with neat and clean polised edges. Profiles make to be 247SIGN/ VISTA Systems/ Glo-lite

Building Directory (Master Directory) (600X1200)

Room Name

Room Name Type 1 (600 X 800)

Room Name Type 2 (300 X 300)

Room Name Type 3 (600 X 300)

Room Name Type 4 (500 X 300)

Room Name Type 5 (300 X 500)

Room Name Type 6 (200 X 250)

Lift No. (Size: 300 X 110)

Lift Lobby (Size: 800 X 200)

Directional Directory, ( Size: 400 X 600)

Supply & installation Signage Made Of Base 3 MM Beton silver/ Beton white/ Swiss snow finish ACP panel Box having 6063 Alloy profiles to house the edge of ACP with in groove. Profile size 25 X 38 mm @edges powder coated as per approved shade make 247SIGN/ VISTA Systems/ Glo-lite. Fascia 3 mm acrylic sheet to be Stuck on base ACP Sheet in staggered manner before fixing of signage then Content CNC Cut Acrylic 2 mm thick fixed on signage facia, hung using SS ropes

Reception (Ceiling Hung) (Size: 800X200)

Waiting Area (Ceiling Hung) (Size: 800 X 200)

Wayfinder (Ceiling Hung double sided) (Size: 800 X 250)

Supply & installation Signage Made Of Base 3 MM ACP panel Box having 6063 Alloy profiles to house the edge of ACP with in groove. Profile size 25 X 38 mm @edges powder coated as per approved shade make 247SIGN/ VISTA Systems/ Glo-lite.. Fascia grade 4 Prismatic retro reflective sheetingon ACP Sheet with Overlay film in desired color, before fixing of signage hung using SS ropes

Basement Ceiling Hung (Parking Double sided) (Size: 1500 X 300)

Basement Ceiling Hung (Parking single sided) (Size:1500 X 300)

Emergency Evacuation Signage :- Round Corner signages with radius 8 to 12 mm, made of 3 mm ACP sheet with premium photoluminicent of illumination upto minimum 2 hours. With UV printing for Graphic and text. Adhering to latest NBC Standards. Mounted using SS scews OR 3M VHB tape, as per directions of engineer incharge. the ACP sheet to make 10 mm Border all across with ACP being visible. The material to be choosen form the premium range of Aludecor / Aluco bond/ Alutech. signage make 247SIGN/ VISTA Systems/ Glo-lite.

STAIR NO. (Size: 400X 125)

STAIR DIRECTION AT LANDING (Size: 300 X 125)

FHC ( Size: 150 X 200)

FIRE ALARM (Size: 150 X 200)

FIRE EXTINGUISHER ( Size:150 X 200)

STAIR FLOOR LEVEL INDICATOR (Size: 382 X 382)

FSD (Size: 300 X 300)

FIRE TOWER ( Size: 400 X 125)

Emergency Evacuation Signage :- Sandwhich Acrylic frame work of 5 mm + 5mm thickness. Signages made of premium photoluminicent of illumination upto minimum 2 hours. With ecosolvent printing for Graphic and text. Adhering to latest NBC Standards providing details fo various Emergency numbers and clear instructions to be useful in case of emergency.. Mounted using SS Spacers 18 mm x 25 mm, as per directions of engineer incharge. Signages to be bilingual language. Signage make 247SIGN/ VISTA Systems/ Glo-lite

EVACUATION PLAN

EVACUATION PLAN

ITEM Name:-Edge Lit Emergency Signage MODEL - EMEX3726- Premium Casing:-Anodised Aluminium with Plastic / Metal Side Caps. Signages Over all size :-375 x 260 mm Text Panel:-8 mm Acrylic Back Up Duration :- 180 Minutes Primary Power Source:-AC - 150-240 Volt Luminare:-LED Battery Disconection Swith Power Consumption :- (3-5) Watt (0.018 to 0.023 Amp). Battery Capacity:- 2000 MAH Battery Type:- Lithium ION AC to DC Built in Adaptor Fuse for Circuit protection AC, Charging, EMERGENCY Indicators Emergency Test Switch Battery Minimum Discharge Protection Battery Maximum Charge Protection Installation:- In client scope through certified electrical contractor. MAKE- 247Sign/ Glo-Lite/ Prolite/

Battery Backup Directional (Size: 375 X 260)

Battery Backup Exit (Size: 375 X 260)

1.0 TR, 4 mm external static

Functions of Network Devices Enable communication by transmitting and receiving data between devices. Allow devices to connect to networks efficiently and securely. Improve network performance by reducing congestion and managing traffic. Provide security by controlling access and preventing unauthorized activities. Extend network coverage and solve signal loss or attenuation problems.

Canon A4 and Legal Colour Laser Computer Printer CanonR (Canon LBP673cdw - 1 Year Warranty)

Computer Server Processor: Features dual Intel Xeon Silver 4514Y processors, offering a total of 32 cores and 64 threads. Memory: Includes 256GB of DDR5 4800MT/s RAM, optimized for performance. Storage: Equipped with a 1.9 TB SATA SSD and supports up to 12 SAS/SATA drives. Power: Uses dual, hot-plug 700W redundant power supplies with Titanium efficiency. Best For: Demanding enterprise workloads and database analytics

productivitysuites likeMicrosoftOffice, securitysoftware likeantivirus, creativeanddesignprograms fromsuites likeAdobeCreativeCloud, andspecializedtoolssuchas compression utilities like WinRAR or professional design software

acer High End Desktop Computer with Warranty 3 Year Description of Stores Desktop Computer with Table Mount Monitor System with Compatible Chipset as per Processor make with Minimum 6 USB Port Base Processor Number NA for Higher Processor Higher Processor Number Intel Core i7- 13700 Trusted Platform Module Discrete TPM 2.0 Factory Pre-loaded Operating System Window 11 Professional RAM Size (Memory Card/Module) (in GB) (Capacity to be Installed in the System) 16 Primary Storage Capacity (in GB) 1024 Availability of Secondary Storage No Secondary Storage Secondary Storage Capacity (in GB) 0 Availibility of Monitor Yes as per IS 13252 (Part 1) Panel Type Vertical Alignment (VA) Screen Size (in CMs) 53.1 - 58 (20.91" - 22.83")

EPSON Standard Throw (0.91 to 2.5) Multimedia Projector (MMP) With 1920 x 1200 (WUXGA) Resolution Product id: 5116877-67405275880

Fasteners: Stapler and staples Hole punch Paper clips and binder clips Cutting & Adhesion: Scissors Tape dispenser and clear tape Glue stick or liquid glue Writing & Correction: Pens (ballpoint, gel) Pencils and eraser Highlighters and markers (permanent/dry-erase) Correction fluid/tape Organization & Stationery Supplies

I. Writing & Marking Instruments II. Paper & Notes III. Fastening & Cutting Tools IV. Filing & Organization Supplies

xerox A3, A4 and Legal Colour Laser Computer Printer xeroxR (Xerox Versalink C7000DN with 1 Year Warranty) Product id: 5116877-12046115344

BLACKDOT Projector Screen 120 Inches BLACKDOTR (BLACKDOT MOTORIZED TRIPOD SCREEN 6X 8 FEET) Product id: 5116877-38854806940

ELCOR Projector Screen 180 Inches ELCORR (TRIPOD PROJECTION SCREEN (LS120INTPS)) Product id: 5116877-15367449711

GN 650 TNM Celfrost 2 Door Reach In Refrigerator ( 600 ltrs. Capacity) Temperature Range : 2 to 8 Deg C Weight : 115 kg Volume : 600 Litre Input Power : 350 W Dimension : 680x800x2010 mm Warranty : 1 Year

ModelThree Sink Wash Unit

Black Nano Kitchen Sink 304 Stainless Steel Waterfall Sink Single Bowl Workstation Kitchen Sink with Multifunctional Digital Display Fly Rain Pull-Out Faucet (Color : Black, Size : 75x45x22CM)

Furniture Sheesham Wood Crockery Cabinet || BrandWOODTREND ColourNatural9 MaterialSheesham Wood Recommended Uses For Productkitchen Product Dimensions33D x 51W x 175H Cen meters Special FeatureSheesham Wood Moun ng TypeFloor Mount Room TypeKitchen Cabinet Home Living Room Furniture Door Stylewood Weight Limit100 Kilograms

Bosch Built in Gas Hob Black Tempered glass Glass 4 Burner Auto Ignition 75 cm True Brass 2D Ring Burners with Matt Black Heat Shields & Cast Iron pan supports (PNI7B6F20I)

ELTONS Rectangular Single Element Induction Heater ELTONSR (Glaze 2200W) Product id: 5116877-3080474858

VEVOR Hot Box Food Warmer, 5-Tier Concession Warmer with Water Tray, 5 Pans, Double-Door and Adjustable Shelves, Stainless Steel Food Warmer Cabinet, Ideal for Storing Pizza, Chicken, Restaurant

Heating type Electric Material SS 304 No. of doors Double door Power rating 1.5 kW Load Capacity 200 kg, 200 Kg Color Silver Body material SS 304 Temperature range 40-90 deg C Size/Dimension Custmised As per Requirment Delivery Time 5-7 Working Days Finishing Type Stainless Steel Power Source Electric Ss Grade 304 SS I Deal In New Only Wheel Type Modern

GIONIEN Electric Cooktop 30",Built-in Stove Top 4 Burners,Ceramic Black Glass Electric Hot Plate Cooktop 30 Inch,220-240V,Child Lock,Fast Heat,6900W,Hot Surface Indicator,Hard Wire,Easy to Clean

120LBS/24H Commercial Ice Maker Machine, Freestanding Stainless Steel with Adjustable Ice Thickness & LCD Control,40 Cubes/Cycle,Self-Cleaning,Quiet Operation for Home,Restaurant,Bar

Stainless Steel Soiled Dish Receiver With Glass Shelf

Material - stainless steel Size - 48 X 24 Inch & 17 Inch Table Top - Glass

KAILA--M/S KAILA INSTRUMENTATION KITCHEN STORAGE Perforated rack of 40 mm square pipe made of 16 SWG sheet

Rudra Silver Stainless Steel Air Tight Container Drum Box with Handle (40 L)

ATLANTIS CLASSIC 4 Lane Tea & Coffee Vending Machine 3 Ltrs hot Tank

LG Domestic Microwave Oven Capacity / Volume (Litres) 28 Product id: 5116877-28389399117

Bathla Advance 7-Step Foldable Aluminium Ladder For Home (Orange)

Suwas Trolley 5 Shelves Powder Coated Bin Storage Rack Without Bins, Load Capacity-80 Kg/Shelf (1 Year Warranty) (SU-SR-016)

Repaar 501-600 Liters Deep Freezer Product id: 5116877-87249399908

onstructed in 304 AISI stainless steel. Framework in mm25 tubing, completely welded. Seamless, sound-absorbing, shelves with double-folded edges. Shelves are welded to the framework. The handles are an extension of the load-bearing frame. N. 4 swivelling castors, two with brakes, mm125 in diameter, fitted with plastic bumpers. Shelves size mm1200x600. Load capacity: 150 kg, uniformly distributed. Buy Electrolux Professional STR122WH 2-TIER SERVICE TROLLEY W/HANDLE 1200 MM (Code 361208) online at a favorable price (prezzo, prix, precio, preço). Weight: 25 kg Net Width: 1295 Net depth: 695 Net Height: 916 Represents a tubular-welded structure when assembled The rack is equipped with two seamless shelves with raised edges Thanks to the fact that the edges of the shelf are bent upwards, it prevents crockery from falling during transport This model is mounted on four 125 mm diameter swiveling rubber wheels, two of which are equipped with locks The wheels are equipped with gray plastic bumpers The materials of which the cart is made meet all the hygienic norms and guarantee the longest possible lifetime of the device The whole cart construction is made of corrosion-free AISI 304 stainless steel The size of the shelves is 1200x600mm Sturdy, ergonomic handle is an extension of the supporting frame The evenly distributed load capacity of 150 kg

Commercial Laundry Basket with Wheels Laundry Trolley on Wheels Heavy Duty Stainless Steel Laundry Sorter Hamper with Handle and Removable Bags for Home Hotel (Size : F)

Unbranded Stainless Steel Grade 202 Dustbin of Capa city 100 Liter

Prabhat Steel SS Perforated Bin - 12 x 16 ( 25 Ltrs ) Stainless Steel Dustbin (Silver)

Lens Point Emergency Light Unit 6 Watt Product id: 5116877-56161133621

JIDESIGN HDPE Pole-Mounted Outdoor Dustbin

Bosch GAS 55 M AFC PROFESSIONAL WET/DRY EXTRACTOR Vacuum cleaners

primepick Prime Pick Twin Spin Mop With Pedal Triangle Mop Set (Grey)

Supply, delivery, testing, and commissioning of a Manual Hydraulic Hand Pallet Truck for lifting and moving palletized loads within the facility. The unit shall be of heavy-duty steel construction with an integrated, serviceable hydraulic pump and a 3-position control lever (Raise, Lower, Neutral). The design should include built-in overload protection and a spring-loaded handle to return to the vertical position when released. Technical Specifications: Load Capacity: 2,500 kg (Minimum) Fork Length: 1150 mm Overall Fork Width: 550 mm (narrow width) or 685 mm (wide width) Lowered Fork Height: 85 mm (Maximum) Max Lift Height: 200 mm (Minimum) Wheel Material: Polyurethane (PU) wheels on all steer and load wheels (Nylon an alternative for smooth floors) Load Wheels: Tandem configuration for even floor contact and stability Material: Heavy-duty steel with anti-corrosive protection and powder-coated finish Warranty: Minimum 12 months against manufacturing defects

Whirlpool Total Volume for Direct Cool 176- 194 Total Volume for Frost-free NA 2 star

godrej Total Volume for Direct Cool 241-275 Total Volume for Frost-free NA 3 starProduct id: 5116877-69630829139

Divine Trends Brass Antique Finish Gold Table Lamp Sleek with Off White 10 Inch Lampshade For Bedroom, Bedside, Living Room, Home Decoration, Hotel Pack Of 1 - Led Bulb Included

SAMSUNG Type/Category/Class of TV set Smart TV(2) Actual Screen Size (inches) 85 LED (Light Emitting Diode) Product id: 5116877-25866486567

CLEANVERSE Scrubber Dryer Electric Walk Behind Type Floor Cleaning MachineProduct id: 5116877-15986379670

BLUE STAR Storage Type Water Cooler 15 LPH Cooling Capacity Product id: 5116877-24034525496

Supply and delivery of a new, king-size quilted double bed cover measuring approximately 229 cm x 254 cm (90x100 inches), crafted from a blend of cotton and microfiber with a thread count of at least 280 TC. The cover shall feature ultrasonic embossing or a durable stitched quilt pattern for enhanced aesthetic and durability, a reversible design with complementing solid colours or subtle prints, finished with a neat border, and supplied with two matching pillow covers, all to be of an approved colour.

Supply and delivery of a standard double flat bed sheet measuring approximately 200 cm x 250 cm (78x98 inches), made from a breathable, durable 100% cotton fabric with a minimum 144 Thread Count (TC). The sheet must be mercerized for improved luster and strength, have colourfast properties meeting basic wash standards, be free from defects (e.g., holes, tears, excessive pilling), and supplied in a plain white or standard light pastel shade as approved by the architect.

Supply and delivery of a new, high-quality, ultra-soft double-bed blanket made from a blended poly-viscose/microfiber material, suitable for heavy winter use, with approximate dimensions of 220 cm x 240 cm (86x94 inches) and a minimum weight (mass) or density of 500 GSM (grams per square meter), finished with a reinforced 1.5 inch wide border on all four sides and supplied in a cherry red or approved solid colour as specified by the engineer-in-charge, conforming to relevant Indian Standards (e.g., aspects of IS 5910 if applicable)

Supply and delivery of a premium double bed down duvet measuring approximately 220 cm x 240 cm (or 90 x 100 inches), filled with a high-quality blend of 50% duck down and 50% duck feather at a minimum fill weight of 450 GSM (or a similar fill power for medium-warmth, all-season use), encased in a 100% cotton, minimum 400 Thread Count (TC), down-proof and anti-dust mite fabric shell with baffle box construction to ensure even fill distribution.

Supply and delivery of a new, durable single-bed cover made from a pre-shrunk, heavy-duty 100% cotton canvas or thick poly-cotton blend fabric, measuring approximately 150 cm x 225 cm (60 x 90 inches), featuring a non-reversible quilted design with a minimum fill density of 150 GSM, a neat bound edge finish on all sides, and supplied in a plain beige or approved solid colour.

Supply and delivery of a standard single flat bed sheet measuring approximately 150 cm x 225 cm (60x90 inches), made from a breathable and durable 100% cotton fabric with a minimum of 144 Thread Count (TC). The sheet shall be colourfast, pre-washed to prevent excessive shrinkage, free from manufacturing defects such as holes or tears, and supplied in a solid white or a basic approved plain colour.

Supply and delivery of a new, soft, and durable single-bed winter blanket made from 100% microfiber or mink material, with approximate dimensions of 150 cm x 225 cm (59x89 inches), a minimum density of 500 GSM (grams per square meter) to provide adequate warmth for cooler climates, finished with a reinforced binding or whip-stitched edge on all four sides, and supplied in a solid, non-fade, manufacturer-approved colour.

HEAVY Curtain Set, As Per Approved Design

LACE Curtain Set, As Per Approved Design

Supply and delivery of a standard size down pillow measuring approximately 46 cm x 66 cm (18 x 26 inches), filled with a high-quality blend of 70% duck feather and 30% white duck down, providing medium-firm support suitable for all sleeping positions. The pillow shall be encased in a 100% cotton, down-proof fabric shell with a minimum of 240 Thread Count (TC), treated to be hypoallergenic and dust-mite resistant, with reinforced double-stitched seams to prevent fill leakage.

Supply and delivery of a standard size pillow slip/cover measuring approximately 46 cm x 69 cm (18 x 27 inches), made from durable, pre-shrunk 100% cotton fabric with a minimum of 200 Thread Count (TC) and a percale weave. The cover shall feature an envelope-style closure to securely hold the pillow, possess colourfast properties (no colour bleeding during washing), have reinforced, double-stitched edges for enhanced longevity, and be supplied in an approved plain white or light solid colour.

Supply and delivery of standard square cushion pads complete with covers, measuring approximately 40 cm x 40 cm (16 x 16 inches). The cushion pad shall be made of high-quality polyurethane (PU) or 'cool foam' of 32 density for adequate bounce and durability. The removable outer cover shall be made of a durable, pre shrunk poly-cotton or similar robust tapestry fabric in a solid, approved colour, featuring a good quality concealed zip closure along one side for easy washing, and finished with neat, double-stitched seams.

Supply and delivery of a new, single cushion cover measuring approximately 45 cm x 45 cm (18 x 18 inches), fabricated from a durable, high-quality upholstery grade jacquard weave or tapestry fabric. The cover shall be pre-shrunk, colourfast, feature an approved aesthetic design or solid colour, and include a robust, concealed zipper closure along one edge, finished with neat double-stitched interior seams to prevent fraying and ensure longevity.

Supply and delivery of a new, full-size 100% cotton bath towel measuring approximately 75 cm x 150 cm (30x60 inches). The towel shall be made from a looped terry weave fabric with a plush feel and a high absorbency rate, specified at a minimum density of 500 GSM (grams per square meter). The edges must have durable, reinforced double-stitched hems to ensure longevity, be colourfast, machine washable, and supplied in a plain white or standard light solid colour.

Supply and delivery of a new, high-absorbency guest hand towel made from 100% ring-spun cotton, measuring approximately 40 cm x 60 cm (16 x 24 inches) or 40 cm x 70 cm (16 x 28 inches). The towel shall have a minimum weight density of 450 GSM (grams per square meter), durable terry loops, reinforced side hems with double stitching to prevent fraying, and be supplied in an approved uniform light grey or white solid colour.

Supply and delivery of a durable and highly absorbent floor towel/bath mat measuring approximately 50 cm x 80 cm (20 x 31.5 inches), made from 100% ring-spun cotton in a thick terry or chevron weave. The towel shall have a high minimum density of 700 GSM (grams per square meter) for plushness and excellent water absorption, a reversible design with reinforced double-stitched hems on all four sides for durability, a non-rubber backing for easy commercial washing and fast drying, and supplied in an approved uniform plain white colour.

Supply and delivery of a compact, wall-mountable First Aid Box constructed from durable white or ivory plastic (ABS) or powder-coated mild steel, measuring approximately 30 cm (H) x 20 cm (W) x 12 cm (D), clearly marked with the universal green 'First Aid' cross symbol. The box shall include a secure latch/locking mechanism (with one key provided) and contain a basic, sealed standard kit appropriate for a small office or residential use, to include a minimum of 20 assorted sterile plasters, 2 sterile gauze pads, 1 adhesive tape roll, 1 bandage roll, antiseptic wipes, a pair of scissors, disposable gloves, a thermometer, and basic first aid instructions.

Supply and delivery of a standard, manual, adult-size folding wheelchair with a durable, lightweight powder-coated steel or aluminum frame, capable of supporting a minimum user weight of 100 kg. The chair shall feature a seat width of approximately 18 inches, comfortable nylon or vinyl upholstery that is easy to clean, fixed armrests, detachable or flip-up footrests with adjustable height, solid rubber rear tires (approx. 24-inch diameter) and front castors (approx. 8-inch diameter) that are puncture-proof. The chair must include reliable push-to-lock wheel brakes, a rear storage pouch, and be easily foldable for transport, conforming to basic quality and safety standards (e.g., aspects of ISO 7176 if applicable).

Supply of Uniform for Staff Specific designs for front desk, housekeeping, etc., comfortable, washable fabric, various styles and colors

Supply of Electric Kettle of 1.8 Litres, suitable for 4-6 cups of water at once. Multicook options might have slightly different capacities. Power Consumption: Kettles in this price range typically use 1300 Watts to 1650 Watts of power, ensuring rapid boiling. Body Material: Options often include a full stainless steel interior/body or a double-wall design featuring a stainless steel inner body and a cool-touch plastic exterior, which prevents accidental burns. Safety Features: Standard safety mechanisms are universal and include: Automatic Shut-Off: The kettle switches off automatically once the water reaches boiling point. Dry Boil Protection: This feature automatically turns off the appliance if there is no water inside, preventing damage. Overheating Protection: Provides a safeguard against the temperature rising too high.

4 Cups: Larah by Borosil Curl Opalware Cup, Set of 6 (160 ml each) for approx. 2 Glasses: Borosil Vision Glass Set, 295 ml

Supply of Toilet Paper Roll like the Prestige Prime 2 Ply Toilet Paper Roll, Length: 52 m or multipacks containing up to 52 rolls, General British Standard (BS) and Bureau of Indian Standards (BIS) specifications, such as IS 14661: 1999, exist for quality control.

SS water jugs with a capacity of around 1500 ml typically feature durable, rust-proof, food-grade stainless steel construction and are available in both single-wall and double-wall insulated designs to serve various temperature retention needs.

elephone instruments available for are typically corded analog landline phones with features such as caller ID, a basic LCD display, speakerphone, and memory for call logs and speed dialing.

Housekeeping Stores

primarilymadeofplastic,glass,or lightmetal, typicallyfeaturingaquartzmovement(eithersilentsweeportraditional ticking)andbattery-poweredoperation.Commonsizes range from small (around 9 inches) to standard (12 inches), with some larger decorative options available, often in round or abstract shapes.

LED bulbs of 12 watts generally provide a brightness of 1000 to 1300 lumens, have common base types like B22 and E27, and offer color temperatures ranging from warm

Chemistry: Alkaline-Manganese Dioxide (Zn/MnO2). Shelf Life: Up to 10 years in ambient storage conditions (5°C to 30°C or 41°F to 86°F) due to Duralock technology. Leakage Prevention: Feature a superior nylon top closure designed to protect devices from damaging leaks. Reusability: Most standard Duracell alkaline batteries are single-use/non-rechargeable. Mercury Content: Typically mercury-free (Hg-free)

Chemistry: Alkaline-Manganese Dioxide (Zn/MnO2). Shelf Life: Up to 10 years in ambient storage conditions (5°C to 30°C or 41°F to 86°F) due to Duralock technology. Leakage Prevention: Feature a superior nylon top closure designed to protect devices from damaging leaks. Reusability: Most standard Duracell alkaline batteries are single-use/non-rechargeable. Mercury Content: Typically mercury-free (Hg-free)

Supply Sundry Items, soaps shampoos etc for one year

Security Service Equipment

Supply high-performance, lightweight hand held metal detector designed for security industry requirements, with an included leather case and battery. Features: It offers sound, vibration, and LED light alarm modes and has an operating frequency of 22 KHz.

Supply and installation Item: Walk-Through Metal Detector (WTMD) Description: Supply, installation, testing, and commissioning of a multi-zone (e.g., 6, 9, or 18 zones) digital WTMD. Includes all standard hardware and software. inculding Power and Data Cabling Description: Supply and installation of required power and data cables from the main control panel to the WTMD. Item: Ground Preparation and Mounting Hardware Description: Includes drilling and plugging anchor points for secure installation and any required flooring adjustments. along with Software Configuration and Programming Description: Includes configuring sensitivity levels, alarm settings, and traffic counter functions according to specified requirements. eith all complite as per direction of E/I

Access Control Management Software: Licensed, web-based, enterprise-level software supporting up to 65,000 doors and 1 million users, with time-attendance and reporting modules. Multi-Door Access Control Panels/Controllers: IP-enabled panels (e.g., 4-door controllers) in metal enclosures with power supply, supporting 12V DC operation, multiple inputs/outputs for locks, exit buttons, and alarms. Card Readers: Contactless smart card readers (ISO 14443) for all entry/exit points, compatible with the control panels and supporting Wiegand/RS-485 communication. Access Credentials: Supply of contactless RFID smart cards for all Doors . Electronic Door Locks: Electromagnetic (EM) locks (minimum 600 lbs holding force) and/or electric strikes, suitable for various door types, complete with mounting brackets. Request-to-Exit (RTE) Devices: Stainless steel or no-touch exit buttons/switches for each controlled door. Door Position Sensors: Magnetic door switches for monitoring door status (open/closed/forced open). Power Supply Units (PSU): Centralized or local 12V DC power supplies with battery backup for uninterrupted operation during power outages. Cabling & Conduits: All necessary shielded data cables (CAT6 or better), power cables, conduits, and cable trays for a complete turnkey installation. Server PC: Business PC with Intel Core i7 14th gen (or equivalent) processor, minimum 24 MB cache, and sufficient RAM/storage for running the application and database servers. Integra on Modules: Hardware/so ware interfaces for integra on with fire alarm systems (for emergency egress), CCTV, and VM

Supplying and installation of 1.0 Washing Machine 1.1 50 kg Capacity, Front Loading 1 Unit IFB IVW 50 2.0 Drying Tumbler 2.1 50 kg Capacity, Electrically Heated 1 Unit Washex India / Stefab TD-50 (Generic Model ID) / TDS 50 (Stefab) 3.0 Flatwork Ironer/Press 3.1 1.5 meter roller length 1 Unit Stefab FRE25-150 or FIS 362 (approx 1.5m roller) 4.0 Water Treatment System 4.1 5 m³/hr Capacity 1 Unit Ion Exchange INDION 900 (Generic Model ID) or similar capacity unit 5.0 Ancillary Equipment & Installation 5.1 Steam Generator/Boiler (if required) 1 Unit Thermax or Steel Fab (Model depends on final heat load calculation) 5.2 Air Compressor 1 Unit ELGi or Atlas Copco (Model depends on required CFM/PSI) 5.3 Laundry Trolleys & Baskets 4 Units Local Vendor N/A (Standard commercial items) with all complete as per direction of E/I

Supply and installation of a complete factory-made (pre-fabricated) modular kitchen, including base units, wall units, tall units, countertop, internal accessories, branded hardware with soft-close mechanisms, integrated appliances, and essential plumbing/electrical fixtures. The work shall be executed as per approved drawings and the highest quality standards, using recommended brands or approved equivalents. A Carcass & Shutters (Cabinetry) 1 Base Units (under counter) 18mm/19mm thick Boiling Water Proof (BWP) plywood (e.g., Century Ply, Greenply, or equivalent approved make) with 0.6mm internal laminate and 1mm thick external finish. Sq. Ft. Varies by design 2 Wall Units (overhead) 18mm/19mm BWP plywood, 0.6mm internal laminate, 1mm thick external finish. Standard depth of 325mm-350mm. Sq. Ft. Varies by design 3 Tall Units/Pantry Units 18mm/19mm BWP plywood, with specialized internal storage systems (e.g., pull-out pantry). Sq. Ft. Varies by design 4 Shutters (Doors/Drawer Fascias) 18mm thick BWP plywood/HDHMR with 1.0mm high-gloss Acrylic/Laminate/Veneer finish on the outside and 0.8mm laminate on the inside. All edges to have 1.5mm-2mm thick machine-cut PVC/ABS edge banding. Sq. Ft. Varies by design B Hardware & Accessories All hardware shall be premium, soft-closing, from international standard brands (e.g., Hettich, Blum, Hafele, or approved equivalent). 5 Hinges Auto-loaded, soft-close Euro type slip-on hinges. Nos. Varies 6 Drawer Systems Tandem boxes or DWD Grass/Nova Sleek soft-close drawer systems with high load capacity (min 45kg). Nos. Varies 7 Internal Accessories SS 304 grade wire baskets (plain, cup & saucer, thali), cutlery trays, anti-slip mats, detergent pull-outs, oil/masala pull-outs, round dustbin cargo. Set/Nos. Varies 8 Handles Aluminium G-type profile handles or stainless steel (SS 304 grade, min 150mm long) brush-finished handles. Nos. Varies 9 Skirting & Legs ABS or aluminium adjustable legs and matching PVC skirting with a waterproof seal at the base. Ltr. Ft. Varies C Countertop & Sink 10 Countertop Material High-quality Granite or engineered Quartz stone (min 18mm-20mm thick), machine polished with an approved edge profile. Sq. Ft. Varies 11 Kitchen Sink Double bowl, satin finish, SS 304 grade sink (min 24x18 inches), under-counter or top-mount installation. Job 1 12 Sink Mixer/Tap High-quality, single-lever sink mixer (hot & cold) of an approved brand. Set 1 D Appliances & Installation Premium brands (e.g., Faber, Elica, Bosch, Siemens or approved equivalent). 13 Hob (Cooktop) Integrated 3 or 4 burner auto-ignition hob. Set 1 14 Chimney (Hood) High-suction (1200+ m³/hr) integrated chimney with filterless/baffle filter technology. Set 1

Design,construction, supply, installation, testing and commissioning of the following Tanks & chamber in 5mm thick MS construction as per the approved calculation including expoxy coating inside the tanks and shade of enamel paint over a coat of primer. The cost shall include the cost of all required MS structure for skid platform walking plateform, handrail, staircase, puddle flanges, foot rest etc. with painting of desired shade of enamel paint over a coat of primer.

Anoxic Tank-- 1.5 X 0.7 X 3.0Mtr + FB Aeration Tank-- 3.35 X 2.0 X 3.0Mtr +FB MBR Tank-- 1.5 X 2.0 X 2.5Mtr +FB Sludge Holding Tank-- 1.3 X 1.5 X 3.0Mtr +FB Treated water tank will be in PVC cap. 2000Ltrs Item Decribe above GRAND TOTAL A+B+C+D

15 mm nominal bore

Providing & fixing C.I double air valve of approved quality with bolts , nuts , rubber insertion etc complete (The tail pieces , tapers etc if required will be paid separately )

25 mm dia

Providing, Fixing, Testing & Commissioning of nitrle rubber insulation on hot water supply pipes. K-Flex, A-Flex, Armacell

20mm (9 mm thickness)

25mm dia (9 mm thickness)

32mm dia (9 mm thickness)

40mm dia (13 mm thickness)

50mm dia (13 mm thickness)

65mm dia (13 mm thickness)

Supply, installation, testing and commissioning built with Drinking Water R.O. 100 LPH unit with micron filtration pre-treatment unit,RO Membrane 75 gpd (4nos), Operating Temperature - 5 degree C to 45, 255 approx recovery of purifier water, 90% approx rejection in TDS, R O Membrance auto flush @ every start, stop and every one hour of working for 1 min, Duty Cycle at least 10 hr/per day, stage of filtration Particulate Filter- Membrane Life Enhancer Filter Sediment Filter Pre-carbon Filter R.O.Membrane Filter Post Carbon Filter, skid mounted R.O. module with pressure pump and pressure tank, complete in all respects.

Providing and fixing M.S. holder-bat clamps of approved design to sand cast iron/ centrifugally cast iron(spun) pipes embedded in and including cement concrete blocks 10x 10 x 10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls, etc.

For 150mm dia pipe

Providing, Fixing of CP brass Towel Rack 600mm long without hanger with 3 hooks and CP brass screws complete as required of approved make jaguar.

Providing & fixing 100mm x 50mm G.I. waste with reducing elbow & nipple cutting chases, the floor / slab, repairs complete as required and connection to GI / CI waste pipe.

Providing and fixing GI inlet fitting with maximum 3 inlets 32,40 or 50 mm size fabricated from 100 dia GI pipes and sockets,fixed to C.I. trap with Drip Seal joint and set in cement concrete as per standard drawing complete as directed by Engineer-incharge.

Installing & fixing cast-iron manhole cover and frame suitable for 600mm dia manhole with lockable and lifting arrangement. The entire iterm shal be epoxy coated and approved by insecticide department.Light duty double seal of size 560 mm dia and total weight of cover & frame to be not less than 116 KG. (Location : O/H Water Tanks Top)

Installing & fixing cast-iron manhole cover and frame suitable for 600mm dia manhole with lockable and lifting arrangement. The entire iterm shal be epoxy coated and approved by insecticide department Medium duty double seal of size 560 mm dia and total weight of cover & frame to be not less than 116 KG. (Location : U/G Water Tanks Top)

Providing and fixing M.S fabricated hot dipped galvinised coating puddle flange comprising of 600 mm dia long M.S class 'B' pipe (screwed end up to 50 mm & flange for more than 50 mm dia) with 6 mm thick M.S plates of required size including cutting holes in centre of plate, inserting pipe & making welded (Arc) joint complete. Same shall be installed with TEC welded joint in position with reinforcement bars of RCC tank wall/slab including making cutout in shuttering during concrete casting of tank of following diameter. (Location: underground/ overhead tanks.) 25 mm dia

Providing and fixing M.S fabricated hot dipped galvinised coating puddle flange comprising of 600 mm dia long M.S class 'B' pipe (screwed end up to 50 mm & flange for more than 50 mm dia) with 6 mm thick M.S plates of required size including cutting holes in centre of plate, inserting pipe & making welded (Arc) joint complete. Same shall be installed with TEC welded joint in position with reinforcement bars of RCC tank wall/slab including making cutout in shuttering during concrete casting of tank of following diameter. (Location: underground/ overhead tanks.) 50 mm dia

Providing and fixing M.S fabricated hot dipped galvinised coating puddle flange comprising of 600 mm dia long M.S class 'B' pipe (screwed end up to 50 mm & flange for more than 50 mm dia) with 6 mm thick M.S plates of required size including cutting holes in centre of plate, inserting pipe & making welded (Arc) joint complete. Same shall be installed with TEC welded joint in position with reinforcement bars of RCC tank wall/slab including making cutout in shuttering during concrete casting of tank of following diameter. (Location: underground/ overhead tanks.) 100 mm dia

Providing and fixing M.S fabricated hot dipped galvinised coating puddle flange comprising of 600 mm dia long M.S class 'B' pipe (screwed end up to 50 mm & flange for more than 50 mm dia) with 6 mm thick M.S plates of required size including cutting holes in centre of plate, inserting pipe & making welded (Arc) joint complete. Same shall be installed with TEC welded joint in position with reinforcement bars of RCC tank wall/slab including making cutout in shuttering during concrete casting of tank of following diameter. (Location: underground/ overhead tanks.) 150 mm dia

Making connection of drain or sewer line with existing manhole including breaking into and manhole good the wall, floors with cement concrete 1:2:4 mix ( 1 Cement : 2 Coarse Sand : 4 Graded Stone Aggregate 20mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 Coarse sand), finishedwitha floating coat of neat ement and making necessary channels for the drain etc, complete: . For pipe 100 to 250 mm diameter

c. All incomers and Buscoupler breakers shall be electrical and mechanical interlocked with suitable accessories. d. 2 Nos. Type-2 SPD 65kA 4P with 1No. Red Indicator Light for SPD with 1Set. SPD Back up fuse 1P 50A 20kA including all necessary accessories.

For Plumbing System as described above.

Providing, fixing, testing and commissioning of Heat pumps using energy heat source from ambient air to Hot water, of High efficiency and energy saving operation, capable of heating water at 55⁰ to 60⁰ C with silent operation (the sound level should not exceed 65 dB). The Heat Pump shall have LCD display control panel with built in diagnostic and troubleshooting information and an inbuilt cycle for defrosting in case icing occurs on evaporator including all other mounting, fitting and controls, all inter connecting wiring/cabling between heat pump and electric panel etc complete in all respect with but not limited to following specifications.

TECHNICAL SPECIFICATIONS FOR EACH UNIT Hot water rated output volume - 950 Ltr/Hr for each pump Power Supply V/Ph/Hz : 400~440V/3 PH/50Hz Suggested Maximum output water temperature in Deg C : 55 ⁰ to 60⁰ C ambient temperature range in Deg C : -5 ⁰C~43 ⁰C Type of Fan : Low Noise axial fan Suggested Noise level: DBA <68 Suggested COP: 3.8 No of Pumps 2 (1W+1S) of 50 KW Each or Equivalent

Providing, fixing, testing and commissioning the Hot Water Storage Tank of following Capacity consisting of S.S 304 cylindrical shape tank. (inlet temperature of hot water storage tank 60-65 deg.C) suitable for minimum 4 Kg /Sqm working pressure. Tank shall be provided with water flow meter, inlet / outlet, overflow, drain connection with MH cover, 6 mm thick SS tank, pressure relief valves, pressure gauge at inlet / outlet with isolation cock, thermometer at inlet / outlet, ball Valve, safety valve, check valve etc. The complete system to be tested to a pressure of 10 Kg/cm2 complete in all respects including temperature indicators, thermostat and other required accessories. Tank shall be insulated with 100 mm thick crown 150 grade & 50 mm rock wool pads of approved quality and cladded with 24 SWG aluminum sheet cladding. TANK CAPACITY - 1000 Ltr.

Providing, fixing ,testing and commissioning suitable complete horizontal/ vertical multistage centrifugal pumping set having stainless steel (SS 304) impellers & shaft and single mechanical seal with pumps suitable for 415 Volts, 3 Phase 50 cycles A.C Supply complete with all standard accessories including , M.S. channel, base plate complete with vibration isolators, isolating valve on suction and discharge, non return valve on discharge, pressure gauges with stop cock and dial type thermometer on suction or discharge.(suitable for hot water temperature up to 85 deg C.) as per the approval of Project-in-charge complete with base frame, necessary foundation as per requirement. No of Pump - 2 (1W+1S) Flow - 950 LPH Per Pump Head - 15 M

Hot water Return pump Providing, fixing ,testing and commissioning suitable complete horizontal/ vertical multistage centrifugal pumping set having stainless steel (SS 304) impellers & shaft and single mechanical seal with pumps suitable for 415 Volts, 3 Phase 50 cycles A.C Supply complete with all standard accessories including , M.S. channel, base plate complete with vibration isolators, isolating valve on suction and discharge, non return valve on discharge, pressure gauges with stop cock and dial type thermometer on suction or discharge.(suitable for hot water temperature up to 85 deg C.), as per the approval of Project-in-charge complete with base frame, necessary foundation as per requirement. No of Pump - 2 (1W+1S) Flow - 950 LPH Per Pump Head - 15 M

COLD WATER FEED PUMP Supply, Installation, Testing & Commissioning of complete composite hydro pneumatic system consisting of horizontal /vertical multistage centrifugal pump having stainless steel SS-304 stage casing and SS 304 impellers with stainless steel SS-304 shaft as per IEC standards and GJL250 cast iron suction & discharge casing with single mechanical seal and pressurized tank of suitable capacity as per manufacturer calculation, complete with all standard accessories including pressure switch, pressure gauges, non-return & isolating valves on suction and delivery side with nuts, bolts & washer including mild steel flanges, where ever required with 3 mm thick rubber insertion, with necessary protection and operational devices i.e alternate pumping operation and shut-off during dry running conditions etc. with suitable electrical motor to be operated on 210/220 OR 400/440 volt 50 cycle AC supply, suitable for following duty and with total no. of pumps - 2 nos.(1 working+1standby) complete with Control Unit Panel, manifolds & chassis, as per the approval of Project-in-charge complete with M.S fabricated base frame, nuts and bolts bolted to cement concrete foundations complete as per requirement. No of Pump - 2 (1W+1S) Flow - 50-100 LPM Per Pump Head - 20-25 M

Supply, Installation, Testing & Commissioning of White ABS plastic bottom inlet 2" for concrete with S.S. screws and regulable .. Flow/ inlet = 9,000 l/hr.

Supply, Installation, Testing & Commissioning of Brass/ Gun Matel Geyser Jet 25mm Outlet Jet Nozzles Standard.etc., complete

Providing, fixing, testing & commissioning of Lights

Supply, Installation, Testing & Commissioning of SS 316 Niche Light 12V 15Watt RGBW (3watt x 5Nos Led) With Niche Standard etc., complete

Supply, Installation, Testing & Commissioning of SS 316 Niche Light 12V 15Watt RGBW (3watt x 5Nos Led) With Niche Standard etc., complete

Supply, Installation, Testing & Commissioning of RGBW Controller,

Providing, fixing, testing & commissioning of Pump

Supply, installation, testing and commissioning of High performance pump in CI with Plastic Pre- filter for silent operation at low temp. with mechanical seal and high quality bearing . Easy -open prefilter cover. Connection with Flange including separation of the motor without touching the pump's hydraulic system 5.5 HP(1W+1S)

Supply, installation, testing and commissioning of single stage/Horizontal self priming centrifugal pumping set with prefilter, heavy duty thermo plastic body, Noryle plastic impeller, stainless steel AISI-316 shaft, mechanicalal seal in stainless steel connected to a TEFC induction motor with built in thermal protection and automatic reset suitable for 220 volts, single phase, 50 cycles A.C supply, IP-55 motor protection complete with basket strainer of adequate capacity 3HP(1W+1S)

Supply, installation, testing and commissioning of single stage/Horizontal self priming centrifugal pumping set with prefilter, heavy duty thermo plastic body, Noryle plastic impeller, stainless steel AISI-316 shaft, mechanicalal seal in stainless steel connected to a TEFC induction motor with built in thermal protection and automatic reset suitable for 220 volts, single phase, 50 cycles A.C supply, IP-55 motor protection complete with basket strainer of adequate capacity 1HP(1W+1S)

Supply, installation, testing and commissioning of drain point

Providing, fixing, testing & commissioning of Filter

Supply, Installation, Testing & Commissioning of TOTALLY ANTI- CORROSIVE Bobbin Wound filter,400mm diameter. Fitted with pressure gauge panel manual air bleeder, water drain and emptying plug.fitted with collector arms and diffuser made from unplasticizedPVC and polypropelene .etc., complete. Max.EN ISO 9001 :2000 Standard.working pressure : 2.5 kg/cm². Flow rate = 6m³/hr.

Glass Media for filter

Providing, fixing, testing & commissioning of ChlorineDosing Unit

Supply, Installation, Testing & Commissioning of Online ChlorineDosing Unit for chlorine made in ABS Plastic

Providing, fixing, testing & commissioning of Control Panel (Equipments Make-L & T, Heger, Elmex, Rishabh, FTC, Esbee, Salzer etc.)

Supply & Commisioning of control panel complete as required. MCC(L&T)Relay(L&T)Push Bottom(Surdhi)Indicator(Surdhi)Auto Mannul Switch(Selzer) Contactors(L&T)as described above and below.etc., complete DOL Starter

Ammeter(Selec),Volt Meter(Selec),

Lugs, Wires, Enclosure, .

Centrifugal Pump and power supply and automation for pump

uPVC pipes

Providing and fixing uPVC 10Kg pressure Pipes. Cut to required lengths including all necessary fittings and specials such as bends, tees, unions, reducers, flanges and plugs etc.

50 mm dia

63 mm dia

75 mm dia

90 mm dia

110 mm dia

uPVC Ball Valve

Providing and fixing Pvc lever operated ball valve of full flow with setting and gland of superior quality having minimum working pressure of 10 kg/cm2 with union, flanges where as required.

32 mm dia (1 1/2")

50 mm dia (1 1/2")

63 mm dia (2")

75 mm dia (2 1/2")

Non Return Valve

PVC-U CHECK VALVE - DIN STANDARD

50 mm dia (1 1/2")

75 mm dia

90 mm dia (3")

Puddles Sleeve

Supply & fixing of following sizes of uPVC 10 Kg puddle flanges uPVC pipe fixed with flanges, length 400 to 600 mm length) on the wall of plantroom, balancing tank and the pool walls. To be laid in between the steel reinforcement before RCC. Does not include any civil work.

50 mm dia (1 1/2")

63 mm dia (2")

90 mm dia (3")

110 mm dia (4")

Supply, laying, testing and commissioning of following size PVC insulated sheathed copper conductor 1100 V grade unarmoured cable with required size of sleeves complete as required.

2 Core 2.5 sqmm

2 Core 4 sqmm

3 Core 2.5 sqmm

FRP Fiber Glass Planter P-27/39 LWH(39x18x24)inch Internal Size:-14*36 Color approved by Landscape architexture choice

FRP Fiber Glass Planter P-37/21 LWH(30x10x21)inch Internal Size:-28*8*6 Color approved by Landscape architexture choice

FRP Fiber Glass Planter P-59/12 LWH(22x15x38)inch Internal Size:-7* Color approved by Landscape architexture choice

FRP Fiber Glass Planter P-62/27 Dia-9" Height-27" Internal Size:-25" Color approved by Landscape architexture choice

FRP Fiber Glass Planter P-42/20 Dia-16" Height- 20" Internal Size:-14"Color approved by Landscape architexture choice

FRP Fiber Glass Planter P-25/18 LWH(18x18x18) Internal Size:-16x16Color approved by Landscape architexture choice

Spathiphyllum

Calathea Triostar

Dracaena marginata

Areca palm

Dieffenbachia

Supply of axial fans for the various applications Capacity : 2500 CFM for Fresh Air

Supply of Jet fans for the various applications Capacity : LCS 355-CPU-2/4-3

Installation,Testing & Commissioing of axial fans for the various applications Capacity : 2500 CFM for Fresh Air

Installation,Testing & Commissioing of Jet fans for the various applications Capacity : LCS 355-CPU-2/4-3

Supply, installation, balancing and commissioning of Rectangular ducting

Supply, installation, testing and commissioning of GI Volume control duct damper

Supply, installation, testing and commissioning of aluminium Supply/Return Air Grills

Supplying, fixing testing commissioning of Supply/Return Air Diffusers

Supply, Installation, Testing and Commissioning of extruded GI Fresh Air Louvers with frame bird screen mounting

Supply and fixing of Nitrile Insulation of required thickness of 6 mm

Supply, Installation, Testing and Commissioning of CANVASS Connection

Supply, Installation, Testing and Commissioning of Flexible Connection

Supplying, Fixing,testing and commissioning of DISC VALVES

Lifting, Shifting of Air Conditioning Units (Matari will be in Client Scope)

Any Civil Work(i.e. Jhari Work, Core cutting etc.,)

Scafolding Charges

Supply of Inverter Air Cooled type Outdoor units of VRF system having hermetically sealed scroll type compressors & separate 1# inverter compressor, condenser coil fabricated from Seamless Copper tube & Plate type Al. Fins of Multi Row with “Anti Corrosive” treatment , Axial Flow, upward throw condenser fan, Condenser fan - motor unit, insulated refrigeration piping, power / control wiring from ELCB/MCB to Unit, and earthing, external wiring between Indoor & Outdoor units, all system controls-safety,External Control Adaptor. The outdoor unit shall be pre charged with first charge of R 410A refrigerant. etc. complete as per Technical Specifications and drawing.Each Outdoor units with High Pressure switch, Fan driver overload protector, Over current relay, Inverter Overload Protector & Fusible Plug. The unit shall be suitable for 415 ± 10 % volts, 50 Hz, 3 phase AC supply, and IP 55 protection.

Capacity : 8.0 HP (Top Discharge)

Capacity : 10.0 HP (Top Discharge)

Capacity : 26.0 HP (Top Discharge)

Capacity : 28.0 HP (Top Discharge)

Supply of Aircooled 4 Way flow Cassette type indoor units with in built Automatic drain-up pump decorative panel, electronic expansion valves, high efficiency filters,6Amps/15 Amps Socket,Cabling from Socket to Unit & other accessories etc with following approximate capacities and suitable for cooling whenever required :

Capacity : 1.0 TR larget Cassette

Capacity : 1.5 TR larget Cassette

Capacity : 2.0 TR larget Cassette

Capacity : 2.3 TR larget Cassette

Capacity : 2.8 TR larget Cassette

Capacity : 3.2 TR larget Cassette

Supply of Aircooled 1 Way flow Cassette type indoor units with in built Automatic drain-up pump decorative panel, electronic expansion valves, high efficiency filters,6Amps/15 Amps Socket,Cabling from Socket to Unit & other accessories etc with following approximate capacities and suitable for cooling whenever required : Capacity : 2.0 TR ONE-WAY Cassette

Supply of following capacity Wall Mounted type Indoor Unit with decorative panel, compact cooling coil, electronic expansion valve, Multi speed fan motors, dynamically balanced blowers, provision for synthetic washable media filter including insulation and suitable for operation on single phase AC supply & remote control operation including Corded Remote Control,Power cabling from socket to Indoor unit.

Capacity : 1.0 TR HI-WALL UNITS

Supply of following capacity Ceiling concealed ductable type unit with in built Automatic drain-up pump decorative panel, electronic expansion valves/kit , high efficiency filters,6Amps/15 Amps Socket,Cabling from Socket to Unit, Corded/Cordless remote & other accessories etc having following approximate capacities.

Capacity : 2.0 TR DUCTED TYPE UNITS

Capacity : 2.5 TR DUCTED TYPE UNITS

Capacity : 3.0 TR DUCTED TYPE UNITS

Capacity : 4.0 TR DUCTED TYPE UNITS

Capacity : 5.0 TR DUCTED TYPE UNITS

Capacity : 6.0 TR DUCTED TYPE UNITS

Capacity : 8.0 TR DUCTED TYPE UNITS

Accessories

Supply of (Imported fittings Y-joints and headers etc) Refnet Units for the VRF Unit between IDU & ODU

For Indoor Unit

For Outdoor Unit

Supply of Corded /Cordless remote controllers for Indoor Units

Installation, Testing & Commisioning of Inverter Air Cooled type Outdoor units of VRF system having hermetically sealed scroll type compressors & separate 1# inverter compressor, condenser coil fabricated from Seamless Copper tube & Plate type Al. Fins of Multi Row with “Anti Corrosive” treatment , Axial Flow, upward throw condenser fan, Condenser fan - motor unit, insulated refrigeration piping, power / control wiring from ELCB/MCB to Unit, and earthing, external wiring between Indoor & Outdoor units, all system controls-safety,External Control Adaptor. The outdoor unit shall be pre charged with first charge of R 410A refrigerant. etc. complete as per Technical Specifications and drawing.Each Outdoor units with High Pressure switch, Fan driver overload protector, Over current relay, Inverter Overload Protector & Fusible Plug. The unit shall be suitable for 415 ± 10 % volts, 50 Hz, 3 phase AC supply, and IP 55 protection.

Capacity : 8.0 HP (Top Discharge)

Capacity : 10.0 HP (Top Discharge)

Capacity : 26.0 HP (Top Discharge)

Capacity : 28.0 HP (Top Discharge)

Installation, Testing & Commisioning of Aircooled of Aircooled 4 Way flow Cassette type indoor units with in built Automatic drain-up pump decorative panel, electronic expansion valves, high efficiency filters,6Amps/15 Amps Socket,Cabling from Socket to Unit & other accessories etc with following approximate capacities and suitable for cooling whenever required :

Capacity : 1.0 TR larget Cassette

Capacity : 1.5 TR larget Cassette

Capacity : 2.0 TR larget Cassette

Capacity : 2.8 TR larget Cassette

Capacity : 2.3 TR larget Cassette

Capacity : 3.2 TR larget Cassette

Installation, Testing & Commisionin of following capacity Wall Mounted type Indoor Unit with decorative panel, compact cooling coil, electronic expansion valve, Multi speed fan motors, dynamically balanced blowers, provision for synthetic washable media filter including insulation and suitable for operation on single phase AC supply & remote control operation including Corded Remote Control,Power cabling from socket to Indoor unit.

Capacity : 1.0 TR HI-WALL UNITS

Installation, Testing & Commisioning of following capacity Wall Mounted type Indoor Unit with decorative panel, compact cooling coil, electronic expansion valve, Multi speed fan motors, dynamically balanced blowers, provision for synthetic washable media filter including insulation and suitable for operation on single phase AC supply & remote control operation including Corded Remote Control,Power cabling from socket to Indoor unit.

Capacity : 1.0 TR HI-WALL UNITS

Installation, Testing & Commisioning of following capacity Ceiling concealed ductable type unit with in built Automatic drain-up pump decorative panel, electronic expansion valves/kit , high efficiency filters,6Amps/15 Amps Socket,Cabling from Socket to Unit, Corded/Cordless remote & other accessories etc having following approximate capacities.

Capacity : 2.0 TR DUCTED TYPE UNITS

Capacity : 2.5 TR DUCTED TYPE UNITS

Capacity : 3.0 TR DUCTED TYPE UNITS

Capacity : 4.0 TR DUCTED TYPE UNITS

Capacity : 5.0 TR DUCTED TYPE UNITS

Capacity : 6.0 TR DUCTED TYPE UNITS

Capacity : 8.0 TR DUCTED TYPE UNITS

Installation, Testing & Commisioning of Refnet Units for the VRF Unit between IDU & ODU

For Indoor Unit

For Outdoor Unit

Installation, Testing & Commisioning of Remote Units for the VRF IDU Unit

Refrigerant Copper Pipe

Supply, installation, testing and commissioning of Refrigerant liquid & gas piping using eddy current tested Copper pipes and fittings like elbows, couplers, tee joints, brass fittings, "U" loops, expansion loops,Refnets etc. Supports consisting of GI box / "C" sections & female anchor fasteners with full threaded GI rods, insulation of pipes using 19 mm thick elastomeric closed cell Nitrile Rubber insulation material having class "O" for fire properties, structural clamps with hard PVC pipe sleeves under the clamps to protect insulation at supports, tagging to enable tracing connectivity to respective units

Dia : 6.4 mm

Dia : 9.5 mm

Dia :12.7 mm

Dia :15.9 mm

Dia :19.1 mm

Dia : 22.2 mm

Dia :28.6 mm

Dia : 34.9 mm

Dia : 41.3 mm

Dia : 44.5 mm

Communication Cable

Supply, Installation, testing and commissioning of Communication Cable between Indoor Unit and Outdoor Unit for following Units

For VRF System(Shielded Communication/Control Cabling 2c x 1.5 Sq.mm with Conduit)

Drain Pipe

Supply,Installation, testing and commissioning of rigid heavy class PVC Piping complete with fittings,supports & duly insulated with 6mm thick closed cell crosslinked polythene (XLPE) tubular insulation

Dia : 25 mm

Dia : 32 mm

Dia : 40 mm

Dia : 50 mm

ADDITIONAL REFRIGERANT GAS

Additional Refrigerant Gas Charging of entire length of Copper tube. for following Units

For VRF System

For VRF System

FRAME WORK

Supply, Fabrication & Installation of MS type Outdoor Stand with all required supports, Paint along with Vibration pads of having following Units

For VRF System

DUCTING & AIR DISTRIBUTION

DUCTING

Supply, installation, balancing and commissioning of Rectangular ducting for above Ducted Split unit

Supply, installation, testing and commissioning of GI Volume control duct damper

Supply, installation, testing and commissioning of powder coated extruded aluminium Supply/Return Air Grills

Supplying, fixing testing commissioning of Supply/Return Air Diffusers

Supply, installation, testing and balancing of Collar Dampers.

Supply, Installation, Testing and Commissioning of extruded GI Fresh Air Louvers with frame bird screen mounting

Supply and fixing of Acoustic lining Insulation of required thickness

Supply and fixing of Nitrile Insulation of required thickness

Supply, Installation, Testing and Commissioning of CANVASS Connection

Supplying, Fixing,testing and commissioning of Fire dampers

Supplying, fixing testing commissioning of Supply/Return Air Slotted Diffusers

MISCELLANEOUS ITEMS

Lifting, Shifting of Air Conditioning Units (Matari will be in Client Scope)

Any Civil Work(i.e. Jhari Work, Core cutting etc.,)

Drain Pump

Scafolding Charges

Supply, Installation, laying and connection of G.I. cable tray(Consider for near BY Outdoor Unit)

Timer

SUPPLY & INSTALLATION - MECHANICAL VENTILATION WORK

VENTILATION INLINE FAN

Supply of Inline fans for the various applications

Capacity : 500 CFM for Toilet Exhaust

Capacity : 500 CFM for Toilet Fresh Air

Capacity : 1000 CFM for Toilet Fresh Air

Supply of Propeller fans for the various applications

Capacity: 150 Dia

Installation,Testing & Commissioing of Inline fans for the various applications

Capacity : 500 CFM for Toilet Exhaust

Capacity : 500 CFM for Toilet Fresh Air

Capacity : 1000 CFM for Toilet Fresh Air

Installation,Testing & Commissioing of Propeller fans for the various applications

Capacity: 150 Dia

Supply, installation, balancing and commissioning of Rectangular ducting

Supply, installation, testing and commissioning of GI Volume control duct damper

Supply, installation, testing and commissioning of aluminium Supply/Return Air Grills

Supplying, fixing testing commissioning of Supply/Return Air Diffusers

Supply, Installation, Testing and Commissioning of extruded GI Fresh Air Louvers with frame bird screen mounting

Supply and fixing of Nitrile Insulation of required thickness of 6 mm

Supply, Installation, Testing and Commissioning of CANVASS Connection

Supply, Installation, Testing and Commissioning of Flexible Connection

Supplying, Fixing,testing and commissioning of DISC VALVES

AMC WORK Providing round the clock Staff / Workmen for day to day opretion and preventive maintenance of Fire Fighting System, Electrical Wiring and Panel, Plumbing System, D. G. Set, Lift and Gate Security of Jharkhand Bhawan premises by deploying neatly dressed workmen in 8 hour’s shift including necessary T&P like torch, ladder. tools and uniform etc. complete, as per the direction of Engineer-in-charge. For Fire Fighting and Detection System Fire Pump Operator

Helper

For DG set DG Operator

DG Helper

For Electrical Panels/Wiring Electrician

Helper

LIFT Operator

Plumbing Plumber

Plumbing Helper

Supervisor

IBMS Equipments (Building Management System, Internet,CCTV, etc.) BMS/CCTV/FAPA operator

Technician (WI-WI/Intercom/Networking)

Helper

CAR Lift and Stack Parking Machine Operator

Sewerage Treatment Plant STP Operator

Helper

Carpentor

Helper

Providing round the clock security guard without gun for watch & ward of Government premises and its all belongings by deploying neatly dressed security guards in 8 hour’s shift including necessary T&P like torch, lathi and uniform etc.complete,as per the direction of Engineer-in-charge. (One job means 8 hour’s duty).

HVAC AMC

Providing round the clock Staffs for Day to Day Operation and Maintenace of HVAC System by deploying neatly dressed Skilled Technician and Helper in 8 hour’s shift including necessary T&P as per the direction of Engineer-in-charge. (One job means 8 hour’s duty). Supervisor (Skilled), 02 No per Day

A. C. Technician (Semi-skilled) 3 no per day

Helper, 3 no per day

Comprehensive maintenance of Three Number Voltas Make Rotary Screw Water Cooled Chilling machine with microprocessor based control panel with VFD multiple compressor Model No ACEGWFVXR1601MHP2 (Capacity - 150Tr.) through OEM (VOLTAS). This Job includes replacement /repair of all spares parts and consumables, Gas leakages, Compressor, switch gears , electricals ,Rewinding of Motor, Heating Element etc. of Machine/Plant, as per approved terms and Conditions and directions of E/I. Periodicity of Preventive Maintenance Service must be Quarterly , (Terms and Conditions Attached)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Painting over Terrace pipeline once in a year

LIFT-AMC

Maintenance work of (04) lift for smooth Operation of LIFT by trained and appropriately skilled personnel. Work includes Periodical examination of safety devices and governor of the equipment. Regularly Examine, Lubricate and adjust the equipment and carry out planned maintenance in a systematic and control manner Using KONE developed techniques and expertise ------ do-----All complete for one year as per approved Terms and Condition of Department. LIFT Passanger Lift-17 Passengers-10 Stoppage

Add 18 % GST

Add 1% Labour Cess

Please Enable Macros to View BoQ information