A) Ajni- Improvement to RB-II type quarter multistoried building in Ajni Colony, under ADEN/HQ subdivision. B) Nagpur improvement to roof, drainage system, water supply pipe line, kitchen otta, road pathway, flooring, plastering at Guard line Rly colony. C) Provision of approach road and two-wheeler parking and improvement to C&W staff room near PF no. 7, beside booster pump house under ADEN/HQ/NGP.

01-PART (A)(1)(a): Ajni-Improvement to RB II type quarter multistoried

02-PART (A)(1)(b): Ajni-Improvement to RB II type quarter multistoried

03-PART (A)(1)(c):Ajni-Improvement to RB II type quarter multistoried

04-PART (A)(1)(d): Ajni-Improvement to RB II type quarter multistoried

05-PART (A)(1)(e): Ajni-Improvement to RB II type quarter multistoried

06-PART (A)(1)(f): Ajni-Improvement to RB II type quarter multistoried

07-PART (A)(2): Ajni-Improvement to RB II type quarter multistoried Above/

08-PART (A)(3):Ajni-Improvement to RB II type quarter multistoried Above/

09-PART (B)(1): Nagpur Improvement to Roof, Drainage system, water Above/

10-PART (B)(2): Nagpur Improvement to Roof, Drainage system, water Above/

11-PART (C) (i): Provision of Approach road and two-wheeler parking Above/

12-PART (C) (ii): Provision of Approach road and two-wheeler parking Above/

13-PART (C) (iii): Provision of Approach road and two-wheeler parking Above/

water supply arrangements etc. at Ajni. RB II (M/S) 498, 374, 409, 406, 405, 413, 411, 414, 412,

Item- 01 MS Item (DSR-2023)

S No. Item No Description of Item Unit Qty Rate Amount

12.0 ROOFING

12.37S RAIN WATER SPOUT AND PIPE

Providing and fixing on wall face

unplasticised Rigid PVC rain water pipes

conforming to IS : 13592 Type A, including

jointing with seal ring conforming to IS :

5382, leaving 10 mm gap for thermal

expansion, (i) Single socketed pipes.

Providing and fixing on wall face

unplasticised - PVC moulded fittings/

accessories for unplasticised Rigid PVC rain

12.42 water pipes conforming to IS : 13592 Type A,

including jointing with seal ring conforming

to IS : 5382, leaving 10 mm gap for thermal

12.42.1 Coupler

12.42.2 Single pushfit Coupler

12.42.4 Single tee without door

12.42.5 Bend 87.5 degree

12.44 Providing and fixing to the inlet mouth of rain Each 25 54.7 1367.5

6 water pipe cast iron grating 15 cm diameter

and weighing not less than 440 grams.

17.0 SANITARY INSTALLATIONS

17.1S General

NAGPUR CR DIVISION-ENGINEERING/CENTRAL RLY

Providing and fixing water closet squatting

pan (Indian type W.C. pan ) with 100 mm

sand cast Iron P or S trap, 10 litre low level

white P.V.C. flushing cistern, including flush

17.1 pipe, with manually controlled device (handle

lever) conforming to IS : 7231,with all fittings

and fixtures complete, including cutting and

making good the walls and floors wherever

17.1.1 White Vitreous china Orissa pattern W.C. pan Each 65 6767.4 439881

7 of size 580x440 mm with integral type foot

Providing and fixing white vitreous china

pedestal type water closet (European type

W.C. pan) with seat and lid, 10 litre low level

white P.V.C. flushing cistern, including flush

17.2 pipe, with manually controlled device (handle

lever), conforming to IS : 7231, with all

fittings and fixtures complete, including

cutting and making good the walls and floors

wherever required :

17.2.1 W.C. pan with ISI marked white solid plastic Each 30 6515.55 195466.5

Providing and fixing wash basin with C.I.

brackets, 15 mm C.P. brass pillar taps, 32

mm C.P. brass waste of standard pattern,

including painting of fittings and brackets,

cutting and making good the walls wherever

17.7.3 White Vitreous China Wash basin size Each 64 2301.75 147312

9 550x400 mm with a pair of 15 mm C.P. brass

Providing and fixing Stainless Steel A ISI 304

(18/8) kitchen sink as per IS:13983 with C.I.

brackets and stainless steel plug 40 mm,

including painting of fittings and brackets,

cutting and making good the walls wherever

17.10.2 Kitchen sink without drain board

Providing and fixing P.V.C. waste pipe for

17.28 sink or wash basin including P.V.C. waste

fittings complete.

17.28.2 Flexible pipe

Providing and fixing PTMT Waste Coupling for

17.69 wash basin and sink, of approved quality and

17.69.1 Waste coupling 31 mm dia of 79 mm length Each 64 115.3 7379.2

12 and 62mm breadth weighing not less than 45

18.0 WATER SUPPLY

18.7S C.P.V.C. PIPES

Providing and fixing Chlorinated Polyvinyl

Chloride (CPVC) pipes, having thermal

stability for hot & cold water supply, and all

CPVC plain & brass threaded fittings,

including fixing the pipe with clamps at 1.00

m spacing. This includes jointing of pipes &

fittings with one step CPVC solvent cement

and testing of joints complete as per

direction of Engineer in Charge. ( Internal

work - Exposed on wall )

NAGPUR CR DIVISION-ENGINEERING/CENTRAL RLY

Providing and fixing Chlorinated Polyvinyl

Chloride (CPVC) pipes, having thermal

stability for hot & cold water supply,

including all CPVC plain & brass threaded

fittings and fixing the pipe with clamps at

1.00 m spacing. This includes jointing of

pipes & fittings with one step CPVC solvent

cement and the cost of cutting chases and

making good the same including testing of

joints complete as per direction of Engineer

in Charge. Concealed work, including cutting

chases and making good the walls etc.

Providing and fixing Chlorinated Polyvinyl

Chloride (CPVC) pipes, having thermal

stability for hot & cold water supply including

all CPVC plain & brass threaded fittings This

18.9 includes jointing of pipes & fittings with one

step CPVC solvent cement, trenching,

refilling & testing of joints complete as per

direction of Engineer in Charge. External

18.54S PTMT FITTINGS

Providing and fixing PTMT bib cock of

approved quality and colour.

weighing not less than 99 gms

Providing and fixing PTMT pillar cock of

approved quality and colour.

weighing not less than 110 gms

Providing and fixing PTMT grating of

approved quality and colour.

18.58.2 Rectangular type with openable circular lid

diameter of the inner hinged round grating

18.59S AIR VALVE & WATER METER (BULK TYPE)

Providing and fixing PTMT Ball cock of

approved quality, colour and make complete

with Epoxy coated aluminium rod with L.P./

H.P.H.D. plastic ball.

weighing not less than 138 gms

18.63 Providing and fixing PTMT angle stop cock 15 Each 65 156.9 10198.5

26 mm nominal bore, weighing not less than 85

Providing and fixing unplasticised P.V.C.

18.74 connection pipe with PTMT Nuts, collar and

bush of approved quality and colour.

Providing and fixing PTMT extension nipple

18.75 for water tank pipe, fittings of approved

quality and colour.

18.75.3 25mm nominal bore, weighing not less than Each 25 113.35 2833.75

NAGPUR CR DIVISION-ENGINEERING/CENTRAL RLY

Schedule 03-PART (A)(1)(c):Ajni-Improvement to RB II type quarter multistoried Building in Ajni

Colony, under ADEN/HQ Sub division.- Structural improvement to multistoried buildings, doors and

windows, flooring, sanitary and water supply arrangements of RB II type quarters in Ajni.-

Improvement to damaged doors and windows causing seepage/leakage through it of multistoried

(A-H-8Nos) etc.

Item- 01 MS Item (DSR-2023)

S No. Item No Description of Item Unit Qty Rate Amount

5.0 REINFORCEMENT CEMENT CONCRETE

5.33S DESIGN MIX CONCRETE

Providing and fixing in position factory made

precast RCC M-40 door and window frames

fixing with hold fast embedded in 1:3:6

concrete block, having excellent smooth

finish as per IS: 6523 with reinforcement of 3

Nos, 6 mm dia main bars tied with 3 mm M.S

stirrups placed @ 200 mm C/C and 6

numbers high strength polymer blocks of

required size for fixing hinges including

providing 6 nos specially designed M.S.

galvanised sleeves for accommodating 6 mm

dia fully threaded bolts for fixing hold fast on

vertical members, providing suitable

arrangement for receiving sliding door bolts

and tower bolt etc. all complete, as per the

direction of Engineer-in-charge. The frame

shall be measured in running metre correct

to two places of decimal.

9.0 WOOD AND P.V.C. WORK

9.1S FRAMES AND TRUSSES

Providing and fixing ISI marked flush door

shutters conforming to IS : 2202 (Part I) non-

decorative type, core of block board

9.21 construction with frame of 1st class hard

wood and well matched commercial 3 ply

veneering with vertical grains or cross bands

and face veneers on both faces of shutters:

9.21.1 35 mm thick including ISI marked Stainless Sqm 230 2392.65 550309.5

Steel butt hinges with necessary screws

Extra for Providing and fixing flush doors with

decorative veneering instead of non

decorative ISI marked flush door shutters

conforming to IS: 2202 (Part I)

9.40S MISCELLANEOUS-WOOD WORK

Providing and fixing M.S. grills of required

pattern in frames of windows etc. with M.S.

9.48 flats, square or round bars etc. including

priming coat with approved steel primer all

9.48.2 Fixed to openings /wooden frames with rawl Kg 3000 238.35 715050

plugs screws etc.

ANODISED ALUMINIUM FITTINGS (ALL

FITTINGS SHALL BE ISI MARKED)

Providing and fixing aluminium sliding door

bolts, ISI marked anodised (anodic coating

9.96 not less than grade AC 10 as per IS : 1868),

transparent or dyed to required colour or

shade, with nuts and screws etc. complete :

NAGPUR CR DIVISION-ENGINEERING/CENTRAL RLY

Providing and fixing aluminium tower bolts,

ISI marked, anodised (anodic coating not less

9.97 than grade AC 10 as per IS : 1868 )

transparent or dyed to required colour or

shade, with necessary screws etc. complete :

Providing and fixing aluminium handles, ISI

marked, anodised (anodic coating not less

9.100 than grade AC 10 as per IS : 1868)

transparent or dyed to required colour or

shade, with necessary screws etc. complete :

9.105S GYPSUM BOARD PARTITIONS

9.119 Providing and fixing factory made P.V.C. door Metre 200 492.7 98540

frame of size 50x47 mm with a wall thickness

of 5 mm, made out of extruded 5 mm rigid

PVC foam sheet, mitred at corners and joined

with 2 Nos of 150 mm long brackets of 15x15

mm M.S. square tube, the vertical door frame

profiles to be reinforced with 19x19 mm M.S.

square tube of 19 gauge, EPDM rubber

gasket weather seal to be provided through

out the frame. The door frame to be fixed to

the wall using M.S. screws of 65/100 mm

size, complete as per manufacturer's

specification and direction of Engineer- in-

Providing and fixing factory made panel PVC

door shutter consisting of frame made out of

M.S. tubes of 19 gauge thickness and size of

19 mm x 19 mm for styles and 15x15 mm for

top & bottom rails. M.S. frame shall have a

coat of steel primers of approved make and

manufacture. M.S. frame covered with 5 mm

thick heat moulded PVC 'C' channel of size

30 mm thickness, 70 mm width out of which

50 mm shall be flat and 20 mm shall be

tapered in 45 degree angle on both side

forming styles and 5 mm thick, 95 mm wide

PVC sheet out of which 75mm shall be flat

and 20 mm shall be tapered in 45 degree on

the inner side to form top and bottom rail

and 115 mm wide PVC sheet out of which 75

9.120 mm shall be flat and 20 mm shall be tapered

on both sides to form lock rail. Top, bottom

and lock rails shall be provided both side of

the panel. 10 mm (5 mm x 2 ) thick, 20 mm

wide cross PVC sheet be provided as gap

insert for top rail & bottom rail, panelling of 5

mm thick both side PVC sheet to be fitted in

the M.S. frame welded/ sealed to the styles &

rails with 7 mm (5 mm+2 mm) thick x 15 mm

wide PVC sheet beading on inner side, and

joined together with solvent cement

adhesive. An additional 5 mm thick PVC strip

of 20 mm width is to be stuck on the interior

side of the 'C' Channel using PVC solvent

adhesive etc. complete as per direction of

Engineer-in-charge, manufacturer's

specification & drawing.

9 9.120.2 30 mm thick pre laminated PVC door shutters Sqm 185 3663.8 677803

10.0 STEEL WORK

10.1S General

Providing and fixing 1 mm thick M.S. sheet

door with frame of 40x40x6 mm angle iron

and 3 mm M.S. gusset plates at the junctions

and corners, all necessary fittings complete,

including applying a priming coat of

approved steel primer.

NAGPUR CR DIVISION-ENGINEERING/CENTRAL RLY

10.5.1 Using M.S. angels 40x40x6 mm for diagonal Sqm 50 5804.35 290217.5

14.0 REPAIRS TO BUILDING

14.75AS ROUTINE MAINTENANCE WORK

14.85 Taking out existing wooden door shutter, Each 128 429.1 54924.8

repair by cutting, painting etc. and refixing of

repaired door shutters to existing door

frames, including replacement of hinges with

screws, etc. as required, all complete as per

the direction of the Engineer-in-charge.

15.0 DISMANTLING AND DEMOLISHING

15.1S General

Dismantling doors, windows and clerestory

windows (steel or wood) shutter including

15.12 chowkhats, architrave, holdfasts etc.

complete and stacking within 50 metres lead

Taking out doors, windows and clerestory

15.13 window shutters (steel or wood) including

stacking within 50 metres lead :

21.0 ALUMINIUM WORK

21.1S General

Providing and fixing aluminium work for

doors, windows, ventilators and partitions

with extruded built up standard tubular

sections/ appropriate Z sections and other

sections of approved make conforming to IS:

733 and IS: 1285, fixing with dash fasteners

of required dia and size, including necessary

filling up the gaps at junctions, i.e. at top,

bottom and sides with required EPDM rubber/

neoprene gasket etc. Aluminium sections

shall be smooth, rust free, straight, mitred

and jointed mechanically wherever required

including cleat angle, Aluminium snap

beading for glazing / panelling, C.P. brass /

stainless steel screws, all complete as per

architectural drawings and the directions of

Engineer-in-charge. (Glazing, panelling and

dash fasteners to be paid for separately) :

21.1.1 For fixed portion

21.1.1.2 Powder coated aluminium (minimum Kg 1050 530.9 557445

thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators

including providing and fixing hinges/ pivots

and making provision for fixing of fittings

wherever required including the cost of EPDM

rubber / neoprene gasket required (Fittings

shall be paid for separately)

21.1.2.2 Powder coated aluminium (minimum Kg 1850 634.45 1173732.5

thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium

door, window, ventilator shutters and

partitions etc. with EPDM rubber / neoprene

21.3 gasket etc. complete as per the architectural

drawings and the directions of engineer-in-

charge . (Cost of aluminium snap beading

shall be paid in basic item):

21.3.2 With float glass panes of 5 mm thickness Sqm 290 1505.25 436522.5

(weight not less than 12.50 kg/sqm)

NAGPUR CR DIVISION-ENGINEERING/CENTRAL RLY

Schedule 04-PART (A)(1)(d): Ajni-Improvement to RB II type quarter multistoried Building in Ajni

Colony, under ADEN/HQ Sub division.-Structural improvement to multistoried buildings, doors and

Schedule windows, flooring, sanitary and water supply arrangements of RB II type quarters in Ajni.-

Dismantling of leaky RCC overhead tanks and steel tanks kept over building/Quarters at Ajni

Item- 01 MS Item (DSR-2023)

S No. Item No Description of Item Unit Qty Rate Amount

15.0 DISMANTLING AND DEMOLISHING

15.1S General

Demolishing cement concrete manually/ by

mechanical means including disposal of

material within 50 metres lead as per

direction of Engineer - in - charge.

(including equivalent design mix)

mechanical means including stacking of steel

2 bars and disposal of unserviceable material

within 50 metres lead as per direction of

Engineer - in- charge.

15.5 Extra for cutting reinforcement bars Sqm 98 1147.2 112425.6

manually/ by mechanical means in R.C.C. or

3 R.B. work (Payment shall be made on the

cross sectional area of R.C.C. or R.B. work) as

per direction of Engineer-in-charge.

Demolishing brick work manually/ by

mechanical means including stacking of

15.7 serviceable material and disposal of

unserviceable material within 50 metres lead

as per direction of Engineer-in-charge.

Dismantling steel work in single sections

15.17 including dismembering and stacking within

50 metres lead in:

15.21 Extra for dismantling trusses, rafters, purlins kg per 2400 .85 2040

etc. of steel work for every additional height metre

of one metre or part thereof beyond 5 height

Schedule 05-PART (A)(1)(e): Ajni-Improvement to RB II type quarter multistoried Building in Ajni

Colony, under ADEN/HQ Sub division.- Structural improvement to multistoried buildings, doors and

Schedule windows, flooring, sanitary and water supply arrangements of RB II type quarters in Ajni.-

Improvement to court yard walls, flooring in rooms, toilet and bathroom, kitchen platform of

multistorid buildings of type II QTRs at Ajni.

Item- 01 MS Item (DSR-2023)

S No. Item No Description of Item Unit Qty Rate Amount

2.0 EARTH WORK

2.1S General

Earth work in excavation by mechanical

means (Hydraulic excavator) / manual means

in foundation trenches or drains (not

exceeding 1.5 m in width or 10 sqm on plan),

2.8 including dressing of sides and ramming of

bottoms, for all lift, including getting out the

excavated soil and disposal of surplus

excavated soil as directed, within a lead of

4.0 CONCRETE WORK

4.1S CEMENT CONCRETE (CAST IN SITU)

Providing and laying in position cement

concrete of specified grade excluding the

cost of centering and shuttering - All work up

to plinth level :

NAGPUR CR DIVISION-ENGINEERING/CENTRAL RLY

derived from natural sources : 6 graded stone

aggregate 20 mm nominal size derived from

natural sources)

5.0 REINFORCEMENT CEMENT CONCRETE

5.1S CAST IN SITU

Providing and laying in position specified

grade of reinforced cement concrete,

5.1 excluding the cost of centering, shuttering,

finishing and reinforcement - All work up to

derived from natural sources : 3 graded stone

aggregate 20 mm nominal size derived from

natural sources)

5.9S FORM WORK

Centering and shuttering including strutting,

propping etc. and removal of form for

5.9.1 Foundations, footings, bases of columns, etc. Sqm 200 392.15 78430

for mass concrete

5.9.3 Suspended floors, roofs, landings, balconies Sqm 50 927.25 46362.5

and access platform

5.9.6 Columns, Pillars, Piers, Abutments, Posts and Sqm 200 961.3 192260

5.22S STEEL REINFORCEMENT

Steel reinforcement for R.C.C. work including

straightening, cutting, bending, placing in

position and binding all complete upto plinth

5.22.6 Thermo-Mechanically Treated bars of grade Kg 800 107.85 86280

Fe-500D or more.

6.0 MASONRY WORK

6.26S EXPOSED BRICK WALL

Brick work with clay flyash F.P.S. (non

modular) brick of class designation 7.5 in

superstructure above plinth level up to floor

five level in :

8.0 CLADDING WORK

8.1S General

Providing and fixing 18 mm thick gang saw

cut, mirror polished, premoulded and

prepolished, machine cut for kitchen

platforms, vanity counters, window sills,

facias and similar locations of required size,

approved shade, colour and texture laid over

20 mm thick base cement mortar 1:4 (1

cement : 4 coarse sand), joints treated with

white cement, mixed with matching pigment,

epoxy touch ups, including rubbing, curing,

moulding and polishing to edges to give high

gloss finish etc. complete at all levels

Raj Nagar Plain white marble/ Udaipur green

marble/ Zebra black marble

Providing edge moulding to 18 mm thick

marble stone counters, Vanities etc.,

8.3 including machine polishing to edge to give

high gloss finish etc. complete as per design

approved by Engineer-in-Charge.

NAGPUR CR DIVISION-ENGINEERING/CENTRAL RLY

8.5 Extra for providing opening of required size & Each 64 978.7 62636.8

shape for wash basin/ kitchen sink in kitchen

platform, vanity counter and similar location

11 in marble/ Granite/ stone work, including

necessary holes for pillar taps etc. including

moulding, rubbing and polishing of cut edges

8.20S STONE WORK DRY CLADDING

8.31 Providing and fixing Ist quality ceramic Sqm 800 1267.95 1014360

glazed wall tiles conforming to IS: 15622

(thickness to be specified by the

manufacturer), of approved make, in all

colours, shades except burgundy, bottle

green, black of any size as approved by

12 Engineer-in-Charge, in skirting, risers of steps

and dados, over 12 mm thick bed of cement

mortar 1:3 (1 cement : 3 coarse sand) and

jointing with grey cement slurry @ 3.3kg per

sqm, including pointing in white cement

mixed with pigment of matching shade

11.0 FLOORING

11.1S General

cement : 2 coarse sand : 4 graded stone

aggregate 20 mm nominal size), including

finishing complete.

11.8 Extra for making chequers of approved Sqm 500 83.85 41925

14 pattern on cement concrete floors, steps,

landing, pavements etc.

11.16S TILE FLOORING

Chequered precast cement concrete tiles 22

mm thick in footpath & courtyard, jointed

with neat cement slurry mixed with pigment

11.20 to match the shade of tiles, including rubbing

and cleaning etc. complete, on 20 mm thick

bed of cement mortar 1:4 (1 cement: 4

15 11.20.1 Light shade pigment using white cement Sqm 120 1402 168240

11.23S STONE FLOORING

Marble stone flooring with 18 mm thick

marble stone, as per sample of marble

approved by Engineer-in-charge, over 20 mm

11.23 (average) thick base of cement mortar 1:4 (1

cement : 4 coarse sand) laid and jointed with

grey cement slurry, including rubbing and

polishing complete with :

11.37S CERAMIC GLAZED TILES

11.37 Providing and laying Ceramic glazed floor Sqm 230 1096.55 252206.5

tiles of size 300x300 mm (thickness to be

specified by the manufacturer) of 1st quality

conforming to IS : 15622 of approved make

in colours such as White, Ivory, Grey, Fume

17 Red Brown, laid on 20 mm thick cement

mortar 1:4 (1 Cement : 4 Coarse sand),

Jointing with grey cement slurry @ 3.3

kg/sqm including pointing the joints with

white cement and matching pigment etc.,

11.41S VITRIFIED FLOOR TILES

NAGPUR CR DIVISION-ENGINEERING/CENTRAL RLY

Providing and laying Vitrified tiles in different

sizes (thickness to be specified by

manufacturer), with water absorption less

than 0.08 % and conforming to I.S. 15622, of

approved make, in all colours & shade, in

11.46 skirting, riser of steps, over 12 mm thick bed

of cement mortar 1:3 (1 cement: 3 coarse

sand), jointing with grey cement slurry @ 3.3

kg/ sqm including grouting the joint with

white cement & matching pigments etc.

13.0 FINISHING

13.1S CEMENT PLASTER (IN FINE SAND)

15 mm cement plaster on the rough side of

single or half brick wall of mix :

15.0 DISMANTLING AND DEMOLISHING

15.1S General

Demolishing cement concrete manually/ by

mechanical means including disposal of

material within 50 metres lead as per

direction of Engineer - in - charge.

(including equivalent design mix)

Schedule 06-PART (A)(1)(f): Ajni-Improvement to RB II type quarter multistoried Building in Ajni

Colony, under ADEN/HQ Sub division. - Structural improvement to multistoried buildings, doors and

windows, flooring, sanitary and water supply arrangements of RB II type quarters in Ajni.- Internal

and External paintingf of staffquarters at Ajni Colony.

Item- 01 MS Item (DSR-2023)

S No. Item No Description of Item Unit Qty Rate Amount

13.0 FINISHING

13.44S EXTERIOR FINISHING

Finishing with Deluxe Multi surface paint

13.48 system for interiors and exteriors using

Primer as per manufacturers specifications :

13.48.1 Two or more coats applied on walls @ 1.25 Sqm 8000 193.7 1549600

1 ltr/10 sqm over and including one coat of

Special primer applied @ 0.75 ltr /10 sqm

13.48.2 Painting wood work with Deluxe Multi Surface Sqm 1000 176.25 176250

Paint of required shade. Two or more coat

2 applied @ 0.90 ltr/10 sqm over an under coat

of primer applied @0.75 ltr/10 sqm of

approved brand and manufacture

13.48.3 Painting Steel work with Deluxe Multi Surface Sqm 800 170.7 136560

Paint to give an even shade. Two or more

3 coat applied @ 0.90 ltr/10 sqm over an under

coat of primer applied @ 0.80 ltr/10 sqm of

approved brand and manufacture

Distempering with 1st quality acrylic

distemper, having VOC (Volatile Organic

Compound ) content less than 50 grams/

litre, of approved brand and manufacture,

including applying additional coats wherever

required, to achieve even shade and colour.

13.91 Removing dry or oil bound distemper, water Sqm 5000 25.15 125750

proofing cement paint and the like by

5 scrapping, sand papering and preparing the

surface smooth including necessary repairs

to scratches etc. complete.

Finishing walls with water proofing cement

paint of required shade :

NAGPUR CR DIVISION-ENGINEERING/CENTRAL RLY

13.109.1 Old work (one or more coats applied @ 2.20 Sqm 10000 112.9 1129000

kg/10 sqm) over priming coat of primer

applied @ 0.80 litrs/10 sqm complete

including cost of Priming coat.

Schedule 07-PART (A)(2): Ajni-Improvement to RB II type quarter multistoried Building in Ajni

Schedule Colony, under ADEN/HQ Sub division.- Repairs to Balcony Chhaja (Front Side, Passage and Kitchen

back side) by Providing PPGI Sheet.

Item- 01 MS Item (DSR-2023)

S No. Item No Description of Item Unit Qty Rate Amount

1.0 CARRIAGE OF MATERIALS

By Mechanical Transport including loading,

unloading and stacking

1.1.18 Disposal of moorum/building rubbish/ malba/ cum 1070 494.1 528687

similar unserviceable, dismantled or waste

material by mechanical transport including

1 loading, transporting, unloading to approved

municipal dumping ground for lead upto 10

km for all lifts, complete as per directions of

Engineer-in-charge.

10.0 STEEL WORK

10.1S General

10.1 Structural steel work in single section, fixed Kg 10000 117.35 1173500

with or without connecting plate, including

2 cutting, hoisting, fixing in position and

applying a priming coat of approved steel

primer all complete.

Steel work in built up tubular (round, square

or rectangular hollow tubes etc.) trusses etc.,

including cutting, hoisting, fixing in position

and applying a priming coat of approved

steel primer, including welding and bolted

with special shaped washers etc. complete.

12.0 ROOFING

12.37S RAIN WATER SPOUT AND PIPE

12.50 Providing and fixing precoated galvanised Sqm 2190 738.65 1617643.5

iron profile sheets (size, shape and pitch of

corrugation as approved by Engineer-in-

charge) of total coated thickness 0.50 mm

(base metal of minimum 0.45 mm thickness

with total coating thickness of 0.05 mm) with

zinc coating 120 grams per sqm as per IS:

277, in 240 mpa steel grade, 5-7 microns

epoxy primer on both side of the sheet and

polyester top coat 15-18 microns. Sheet

4 should have protective guard film of 25

microns minimum to avoid scratches during

transportation and should be supplied in

single length upto 12 metre or as desired by

Engineer-in-charge. The sheet shall be fixed

using self drilling /self tapping screws of size

(5.5x 55 mm) with EPDM seal, complete upto

any pitch in horizontal/ vertical or curved

surfaces, excluding the cost of purlins, rafters

and trusses and including cutting to size and

shape wherever required.

13.0 FINISHING

13.1S CEMENT PLASTER (IN FINE SAND)

15 mm cement plaster on the rough side of

single or half brick wall of mix :

15.0 DISMANTLING AND DEMOLISHING

15.1S General

NAGPUR CR DIVISION-ENGINEERING/CENTRAL RLY

mechanical means including stacking of steel

6 bars and disposal of unserviceable material

within 50 metres lead as per direction of

Engineer - in- charge.

15.56 Dismantling old plaster or skirting raking out Sqm 330 54.65 18034.5

joints and cleaning the surface for plaster

including disposal of rubbish to the dumping

ground within 50 metres lead.

Schedule 08-PART (A)(3):Ajni-Improvement to RB II type quarter multistoried Building in Ajni

Colony, under ADEN/HQ Sub division.- Repairs to Fencing and Gate of Staff Quarter Ajni.

Item- 01 MS Item (DSR-2023)

S No. Item No Description of Item Unit Qty Rate Amount

2.0 EARTH WORK

2.1S General

Earth work in excavation by mechanical

means (Hydraulic excavator) / manual means

in foundation trenches or drains (not

exceeding 1.5 m in width or 10 sqm on plan),

2.8 including dressing of sides and ramming of

bottoms, for all lift, including getting out the

excavated soil and disposal of surplus

excavated soil as directed, within a lead of

4.0 CONCRETE WORK

4.1S CEMENT CONCRETE (CAST IN SITU)

Providing and laying in position cement

concrete of specified grade excluding the

cost of centering and shuttering - All work up

to plinth level :

derived from natural sources : 6 graded stone

aggregate 20 mm nominal size derived from

natural sources)

5.0 REINFORCEMENT CEMENT CONCRETE

5.1S CAST IN SITU

Providing and laying in position specified

grade of reinforced cement concrete,

5.1 excluding the cost of centering, shuttering,

finishing and reinforcement - All work up to

derived from natural sources : 3 graded stone

aggregate 20 mm nominal size derived from

natural sources)

10.0 STEEL WORK

10.1S General

10.1 Structural steel work in single section, fixed Kg 6500 117.35 762775

with or without connecting plate, including

4 cutting, hoisting, fixing in position and

applying a priming coat of approved steel

primer all complete.

Steel work in built up tubular (round, square

or rectangular hollow tubes etc.) trusses etc.,

including cutting, hoisting, fixing in position

and applying a priming coat of approved

steel primer, including welding and bolted

with special shaped washers etc. complete.

16.0 ROAD WORK

16.49S MISCELLANEOUS

NAGPUR CR DIVISION-ENGINEERING/CENTRAL RLY

Providing and fixing G.I. chain link fabric

fencing of required width in mesh size 50x50

mm including strengthening with 2 mm dia

wire or nuts, bolts and washers as required

complete as per the direction of Engineer-in-

Schedule 09-PART (B)(1): Nagpur Improvement to Roof, Drainage system, water supply pipe line,

Kitchen Otta, Road Pathway, flooring, Plastering at Guard line Railway Colony.

Item- 01 MS Item (DSR-2023)

S No. Item No Description of Item Unit Qty Rate Amount

2.0 EARTH WORK

2.1S General

Earth work in excavation by mechanical

means (Hydraulic excavator)/manual means

over areas (exceeding 30 cm in depth, 1.5 m

2.6 in width as well as 10 sqm on plan) including

getting out and disposal of excavated earth

lead upto 50 m and for all lift, as directed by

Engineer-in-charge.

Earth work in excavation by mechanical

means (Hydraulic excavator)/manual means

over areas (exceeding 30 cm in depth, 1.5 m

2.7 in width as well as 10 sqm on plan) including

getting out and disposal of excavated earth

lead upto 50 m and lift upto 1.5 m, as

directed by Engineer-in-charge.

Excavating trenches by mechanical/manual

means of required width for pipes, cables,

etc including excavation for sockets, and

dressing of sides, ramming of bottoms, for all

depth, including getting out the excavated

2.10 soil, and then returning the soil as required,

in layers not exceeding 20 cm in depth,

including consolidating each deposited layer

by ramming, watering, etc. and disposing of

surplus excavated soil as directed, within a

2.10.1 All kinds of soil

3 2.10.1.1 Pipes, cables etc, not exceeding 80 mm dia. Metre 50 215.6 10780

2.10.1.2 Pipes, cables etc. exceeding 80 mm dia. but Metre 1000 352.15 352150

not exceeding 300 mm dia

2.25 Filling available excavated earth (excluding cum 40 196 7840

rock) in trenches, plinth, sides of foundations

etc. in layers not exceeding 20 cm in depth,

consolidating each deposited layer by

ramming and watering, lead up to 50 and for

4.0 CONCRETE WORK

4.1S CEMENT CONCRETE (CAST IN SITU)

Providing and laying in position cement

concrete of specified grade excluding the

cost of centering and shuttering - All work up

to plinth level :

(zone-III) derived from natural sources : 3

graded stone aggregate 20 mm nominal size

derived from natural sources)

derived from natural sources : 6 graded stone

aggregate 40 mm nominal size derived from

natural sources)

NAGPUR CR DIVISION-ENGINEERING/CENTRAL RLY

Providing and laying cement concrete in

retaining walls, return walls, walls (any

thickness) including attached pilasters,

columns, piers, abutments, pillars, posts,

4.2 struts, buttresses, string or lacing courses,

parapets, coping, bed blocks, anchor blocks,

plain window sills, fillets, sunken floor etc., up

to floor five level, excluding the cost of

centering, shuttering and finishing:

(zone-III) derived from natural sources : 3

graded stone aggregate 20 mm nominal size

derived from natural sources).

4.10S DAMP-PROOF COURSE

4.12 Extra for providing and mixing water proofing per bag 200 18.15 3630

material in cement concrete work in doses by of 50 kg

weight of cement as per manufacturer's cement

specification. used

5.0 REINFORCEMENT CEMENT CONCRETE

5.1S CAST IN SITU

Providing and laying in position specified

grade of reinforced cement concrete,

5.1 excluding the cost of centering, shuttering,

finishing and reinforcement - All work up to

derived from natural sources : 3 graded stone

aggregate 20 mm nominal size derived from

natural sources)

Reinforced cement concrete work in walls

(any thickness), including attached pilasters,

buttresses, plinth and string courses, fillets,

5.2 columns, pillars, piers, abutments, posts and

struts etc. above plinth level up to floor five

level, excluding cost of centering, shuttering,

finishing and reinforcement :

derived from natural sources : 3 graded stone

aggregate 20 mm nominal size derived from

natural sources)

5.3A Reinforced cement concrete work in beams, cum 5 11334.7 56673.5

suspended floors, roofs having slope up to 15

degree landings, balconies, shelves, chajjas,

lintels, bands, plain window sills, staircases

and spiral staircases above plinth level up to

floor five level excluding the cost of

12 centering, shuttering, finishing and

reinforcement, with 1:1.5:3 (1 cement : 1.5

coarse sand including manufactured sand

derived from Recycled Concrete Aggregate

(RCA) upto 20%: 3 graded stone aggregate

20 mm nominal size including Recycled

Concrete Aggregate (RCA) upto 20%)

5.9S FORM WORK

Centering and shuttering including strutting,

propping etc. and removal of form for

5.9.1 Foundations, footings, bases of columns, etc. Sqm 120 392.15 47058

for mass concrete

5.9.2 Walls (any thickness) including attached Sqm 4500 842.5 3791250

14 pilasters, buttresses, plinth and string

5.9.5 Lintels, beams, plinth beams, girders, Sqm 30 736.4 22092

bressummers and cantilevers

5.9.6 Columns, Pillars, Piers, Abutments, Posts and Sqm 30 961.3 28839

5.22S STEEL REINFORCEMENT

NAGPUR CR DIVISION-ENGINEERING/CENTRAL RLY

Steel reinforcement for R.C.C. work including

straightening, cutting, bending, placing in

position and binding all complete upto plinth

5.22.6 Thermo-Mechanically Treated bars of grade Kg 9600 107.85 1035360

Fe-500D or more.

Steel reinforcement for R.C.C. work including

straightening, cutting, bending, placing in

position and binding all complete above

5.22A.6 Thermo-Mechanically Treated bars of grade Kg 200 107.85 21570

Fe-500D or more.

6.0 MASONRY WORK

6.1S General

Brick work with common burnt clay modular

6.2 bricks of class designation 7.5 in foundation

6.26S EXPOSED BRICK WALL

6.47 Providing and laying Autoclaved Aerated cum 20 8333.65 166673

Concrete (AAC) blocks masonry with 150 mm

to 300 mm thick with Grade -1 AAC blocks of

density 551 to 650 kg/cum conforming to IS:

2185 (Part 3) in super structure above plinth

20 level up to floor V level with RCC band at sill

level and lintel level with approved block

laying polymer modified adhesive mortar all

complete as per direction of Engineer-in-

Charge. (The payment of RCC band and

reinforcement shall be made for separately).

7.0 STONE WORK

7.1S RANDOM RUBBLE MASONRY

Random rubble masonry with hard stone in

superstructure above plinth level and upto

floor five level, including levelling up with

7.2 cement concrete 1:6:12 (1 cement : 6 coarse

sand : 12 graded stone aggregate 20 mm

nominal size) at window sills, ceiling level

8.0 CLADDING WORK

8.1S General

Providing and fixing 18 mm thick gang saw

cut, mirror polished, premoulded and

prepolished, machine cut for kitchen

platforms, vanity counters, window sills,

facias and similar locations of required size,

approved shade, colour and texture laid over

20 mm thick base cement mortar 1:4 (1

cement : 4 coarse sand), joints treated with

white cement, mixed with matching pigment,

epoxy touch ups, including rubbing, curing,

moulding and polishing to edges to give high

gloss finish etc. complete at all levels

Granite stone slab colour black, Cherry/Ruby

Providing edge moulding to 18 mm thick

marble stone counters, Vanities etc.,

8.3 including machine polishing to edge to give

high gloss finish etc. complete as per design

approved by Engineer-in-Charge.

NAGPUR CR DIVISION-ENGINEERING/CENTRAL RLY

8.5 Extra for providing opening of required size & Each 5 978.7 4893.5

shape for wash basin/ kitchen sink in kitchen

platform, vanity counter and similar location

25 in marble/ Granite/ stone work, including

necessary holes for pillar taps etc. including

moulding, rubbing and polishing of cut edges

8.6 Mirror polishing on marble work/Granite Sqm 6 506.7 3040.2

26 work/stone work where ever required to give

high gloss finish complete.

8.20S STONE WORK DRY CLADDING

8.31 Providing and fixing Ist quality ceramic Sqm 400 1267.95 507180

glazed wall tiles conforming to IS: 15622

(thickness to be specified by the

manufacturer), of approved make, in all

colours, shades except burgundy, bottle

green, black of any size as approved by

27 Engineer-in-Charge, in skirting, risers of steps

and dados, over 12 mm thick bed of cement

mortar 1:3 (1 cement : 3 coarse sand) and

jointing with grey cement slurry @ 3.3kg per

sqm, including pointing in white cement

mixed with pigment of matching shade

9.0 WOOD AND P.V.C. WORK

9.1S FRAMES AND TRUSSES

Providing wood work in frames of doors,

windows, clerestory windows and other

frames, wrought framed and fixed in position

with hold fast lugs or with dash fasteners of

required dia & length (hold fast lugs or dash

fastener shall be paid for separately).

Providing and fixing panelling or panelling

and glazing in panelled or panelled and

glazed shutters for doors, windows and

clerestory windows (Area of opening for

panel inserts excluding portion inside

grooves or rebates to be measured).

Panelling for panelled or panelled and glazed

shutters 25 mm to 40 mm thick :

9.7.7 Float glass panes

9.7.7.2 5.0 mm thick glass panes (weight not less Sqm 350 2600.45 910157.5

than 12.50 kg/sqm).

9.7.8 Fly proof stainless steel grade 304 wire Sqm 350 1800.45 630157.5

30 gauge with 0.5 mm dia. wire and 1.4 mm

wide aperture with matching wood beading

Providing and fixing ISI marked flush door

shutters conforming to IS : 2202 (Part I)

decorative type, core of block board

9.20 construction with frame of 1st class hard

wood and well matched teak 3 ply veneering

with vertical grains or cross bands and face

veneers on both faces of shutters.

9.20.2 30 mm thick including ISI marked Stainless Sqm 60 3167.95 190077

Steel butt hinges with necessary screws

9.40S MISCELLANEOUS-WOOD WORK

Providing and fixing M.S. grills of required

pattern in frames of windows etc. with M.S.

9.48 flats, square or round bars etc. including

priming coat with approved steel primer all

COPER OXIDISED MILD STEEL FITTINGS

(COPPER OXIDISED AS PER IS: 1378)

NAGPUR CR DIVISION-ENGINEERING/CENTRAL RLY

Providing and fixing ISI marked oxidised M.S.

9.62 sliding door bolts with nuts and screws etc.

complete (Copper oxidised as per IS 1378)

Providing and fixing ISI marked oxidised M.S.

tower bolt black finish, (Barrel type) with

necessary screws etc. complete (Copper

oxidised as per IS 1378)

Providing and fixing ISI marked oxidised M.S.

door latches conforming to IS:5930 with

screws etc. complete (Copper oxidised as per

ANODISED ALUMINIUM FITTINGS (ALL

FITTINGS SHALL BE ISI MARKED)

Providing and fixing ISI marked aluminium

butt hinges anodised (anodic coating not less

9.95 than grade AC 10 as per IS: 1868)

transparent or dyed to required colour or

shade with necessary screws etc.complete:

Providing and fixing aluminium sliding door

bolts, ISI marked anodised (anodic coating

9.96 not less than grade AC 10 as per IS : 1868),

transparent or dyed to required colour or

shade, with nuts and screws etc. complete :

Providing and fixing aluminium tower bolts,

ISI marked, anodised (anodic coating not less

9.97 than grade AC 10 as per IS : 1868 )

transparent or dyed to required colour or

shade, with necessary screws etc. complete :

Providing and fixing aluminium handles, ISI

marked, anodised (anodic coating not less

9.100 than grade AC 10 as per IS : 1868)

transparent or dyed to required colour or

shade, with necessary screws etc. complete :

9.105S GYPSUM BOARD PARTITIONS

9.119 Providing and fixing factory made P.V.C. door Metre 250 492.7 123175

frame of size 50x47 mm with a wall thickness

of 5 mm, made out of extruded 5 mm rigid

PVC foam sheet, mitred at corners and joined

with 2 Nos of 150 mm long brackets of 15x15

mm M.S. square tube, the vertical door frame

profiles to be reinforced with 19x19 mm M.S.

square tube of 19 gauge, EPDM rubber

gasket weather seal to be provided through

out the frame. The door frame to be fixed to

the wall using M.S. screws of 65/100 mm

size, complete as per manufacturer's

specification and direction of Engineer- in-

NAGPUR CR DIVISION-ENGINEERING/CENTRAL RLY

Providing and fixing factory made panel PVC

door shutter consisting of frame made out of

M.S. tubes of 19 gauge thickness and size of

19 mm x 19 mm for styles and 15x15 mm for

top & bottom rails. M.S. frame shall have a

coat of steel primers of approved make and

manufacture. M.S. frame covered with 5 mm

thick heat moulded PVC 'C' channel of size

30 mm thickness, 70 mm width out of which

50 mm shall be flat and 20 mm shall be

tapered in 45 degree angle on both side

forming styles and 5 mm thick, 95 mm wide

PVC sheet out of which 75mm shall be flat

and 20 mm shall be tapered in 45 degree on

the inner side to form top and bottom rail

and 115 mm wide PVC sheet out of which 75

9.120 mm shall be flat and 20 mm shall be tapered

on both sides to form lock rail. Top, bottom

and lock rails shall be provided both side of

the panel. 10 mm (5 mm x 2 ) thick, 20 mm

wide cross PVC sheet be provided as gap

insert for top rail & bottom rail, panelling of 5

mm thick both side PVC sheet to be fitted in

the M.S. frame welded/ sealed to the styles &

rails with 7 mm (5 mm+2 mm) thick x 15 mm

wide PVC sheet beading on inner side, and

joined together with solvent cement

adhesive. An additional 5 mm thick PVC strip

of 20 mm width is to be stuck on the interior

side of the 'C' Channel using PVC solvent

adhesive etc. complete as per direction of

Engineer-in-charge, manufacturer's

specification & drawing.

Providing and fixing stainless steel fancy

handle of approved make fixed with SS

screws etc. complete as per direction of

Engineer-in-charge.

10.0 STEEL WORK

10.1S General

10.1 Structural steel work in single section, fixed Kg 3000 117.35 352050

with or without connecting plate, including

43 cutting, hoisting, fixing in position and

applying a priming coat of approved steel

primer all complete.

Providing and fixing 1 mm thick M.S. sheet

door with frame of 40x40x6 mm angle iron

and 3 mm M.S. gusset plates at the junctions

and corners, all necessary fittings complete,

including applying a priming coat of

approved steel primer.

10.5.1 Using M.S. angels 40x40x6 mm for diagonal Sqm 10 5804.35 58043.5

Steel work in built up tubular (round, square

or rectangular hollow tubes etc.) trusses etc.,

including cutting, hoisting, fixing in position

and applying a priming coat of approved

steel primer, including welding and bolted

with special shaped washers etc. complete.

11.0 FLOORING

11.37S CERAMIC GLAZED TILES

NAGPUR CR DIVISION-ENGINEERING/CENTRAL RLY

11.39 Providing and laying rectified Glazed Ceramic Sqm 120 1330 159600

floor tiles of size 300x300 mm or more

(thickness to be specified by the

manufacturer), of 1st quality conforming to IS

: 15622, of approved make, in colours White,

46 Ivory, Grey, Fume Red Brown, laid on 20 mm

thick cement mortar 1:4 (1 Cement: 4 Coarse

sand), jointing with grey cement slurry @ 3.3

kg/ sqm including grouting the joints with

white cement and matching pigments etc.,

11.41S VITRIFIED FLOOR TILES

Providing and laying vitrified floor tiles in

different sizes (thickness to be specified by

the manufacturer) with water absorption less

than 0.08% and conforming to IS: 15622, of

approved make, in all colours and shades,

laid on 20mm thick cement mortar 1:4 (1

cement : 4 coarse sand), jointing with grey

cement slurry @ 3.3 kg/ sqm including

grouting the joints with white cement and

matching pigments etc., complete.

Providing and laying Vitrified tiles in floor

with different sizes (thickness to be specified

by the manufacturer), with water absorption

less than 0.08% and conforming to IS:15622,

of approved brand & manufacturer, in all

11.49 colours and shade, laid with cement based

high polymer modified quick set tile adhesive

(water based) conforming to IS : 15477, in

average 6 mm thickness, including grouting

of joints (Payment for grouting of joints to be

made separately).

12.0 ROOFING

12.1S SHEET ROOFING

12.11 Extra for providing and fixing wind ties of 40x Metre 1000 195.6 195600

6 mm flat iron section.

12.37S RAIN WATER SPOUT AND PIPE

NAGPUR CR DIVISION-ENGINEERING/CENTRAL RLY

Providing and fixing false ceiling at all height

including providing and fixing of frame work

made of special sections, power pressed

from M.S. sheets and galvanized with zinc

coating of 120 gms/sqm (both side inclusive)

as per IS : 277 and consisting of angle cleats

of size 25 mm wide x 1.6 mm thick with

flanges of 27 mm and 37 mm, at 1200 mm

centre to centre, one flange fixed to the

ceiling with dash fastener 12.5 mm dia x 50

mm long with 6 mm dia bolts, other flange of

cleat fixed to the angle hangers of

25x10x0.50 mm of required length with nuts

& bolts of required size and other end of

angle hanger fixed with intermediate G.I.

channels 45x15x0.9 mm running at the

spacing of 1200 mm centre to centre, to

which the ceiling section 0.5 mm thick

bottom wedge of 80 mm with tapered

flanges of 26 mm each having lips of 10.5

mm, at 450 mm centre to centre, shall be

fixed in a direction perpendicular to G.I.

intermediate channel with connecting clips

made out of 2.64 mm dia x 230 mm long G.I.

wire at every junction, including fixing

perimeter channels 0.5 mm thick 27 mm

high having flanges of 20 mm and 30 mm

long, the perimeter of ceiling fixed to

wall/partition with the help of rawl plugs at

450 mm centre, with 25mm long dry wall

screws @ 230 mm interval, including fixing of

gypsum board to ceiling section and

perimeter channel with the help of dry wall

screws of size 3.5 x 25 mm at 230 mm c/c,

including jointing and finishing to a flush

finish of tapered and square edges of the

board with recommended jointing compound

, jointing tapes , finishing with jointing

compound in 3 layers covering upto 150 mm

on both sides of joint and two coats of primer

suitable for board, all as per manufacturer's

specification and also including the cost of

making openings for light fittings, grills,

diffusers, cutouts made with frame of

perimeter channels suitably fixed, all

complete as per drawings, specification and

direction of the Engineer in Charge but

excluding the cost of painting with :

12.45.1 12.5 mm thick tapered edge gypsum plain Sqm 500 1355.8 677900

50 board conforming to IS: 2095- (Part I) :2011

(Board with BIS certification marks)

NAGPUR CR DIVISION-ENGINEERING/CENTRAL RLY

12.50 Providing and fixing precoated galvanised Sqm 2500 738.65 1846625

iron profile sheets (size, shape and pitch of

corrugation as approved by Engineer-in-

charge) of total coated thickness 0.50 mm

(base metal of minimum 0.45 mm thickness

with total coating thickness of 0.05 mm) with

zinc coating 120 grams per sqm as per IS:

277, in 240 mpa steel grade, 5-7 microns

epoxy primer on both side of the sheet and

polyester top coat 15-18 microns. Sheet

51 should have protective guard film of 25

microns minimum to avoid scratches during

transportation and should be supplied in

single length upto 12 metre or as desired by

Engineer-in-charge. The sheet shall be fixed

using self drilling /self tapping screws of size

(5.5x 55 mm) with EPDM seal, complete upto

any pitch in horizontal/ vertical or curved

surfaces, excluding the cost of purlins, rafters

and trusses and including cutting to size and

shape wherever required.

Providing and fixing precoated galvanised

steel sheet roofing accessories of total

coated thickness 0.50 mm (base metal of

minimum 0.45 mm thickness with total

coating thickness of 0.05 mm) with Zinc

coating 120 grams per sqm as per IS: 277, in

240 mpa steel grade, 5-7 microns epoxy

primer on both side of the sheet and

polyester top coat 15-18 microns using self

drilling/ self tapping screws complete :

13.0 FINISHING

13.1S CEMENT PLASTER (IN FINE SAND)

15 mm cement plaster on the rough side of

single or half brick wall of mix :

13.44S EXTERIOR FINISHING

Finishing with Deluxe Multi surface paint

13.48 system for interiors and exteriors using

Primer as per manufacturers specifications :

13.48.2 Painting wood work with Deluxe Multi Surface Sqm 3000 176.25 528750

Paint of required shade. Two or more coat

54 applied @ 0.90 ltr/10 sqm over an under coat

of primer applied @0.75 ltr/10 sqm of

approved brand and manufacture

13.48.3 Painting Steel work with Deluxe Multi Surface Sqm 1000 170.7 170700

Paint to give an even shade. Two or more

55 coat applied @ 0.90 ltr/10 sqm over an under

coat of primer applied @ 0.80 ltr/10 sqm of

approved brand and manufacture

13.80 Providing and applying white cement based Sqm 5000 156.05 780250

putty of average thickness 1 mm, of

56 approved brand and manufacturer, over the

plastered wall surface to prepare the surface

even and smooth complete.

Wall painting with premium acrylic emulsion

paint of interior grade, having VOC (Volatile

Organic Compound ) content less than 50

13.83 grams/ litre of approved brand and

manufacture, including applying additional

coats wherever required to achieve even

shade and colour.

Applying priming coats with primer of

13.85 approved brand and manufacture, having low

VOC (Volatile Organic Compound ) content.

NAGPUR CR DIVISION-ENGINEERING/CENTRAL RLY

13.85.3 With water thinnable cement primer on wall Sqm 8000 73.95 591600

58 surface having VOC content less than 50

13.88 Removing white or colour wash by scrapping Sqm 10000 19.75 197500

and sand papering and preparing the surface

smooth including necessary repairs to

scratches etc. complete

Finishing walls with Acrylic Smooth exterior

paint of required shade :

13.111.1 Old work (Two or more coat applied @ 1.67 Sqm 5000 120.75 603750

ltr/ 10 sqm) on existing cement paint surface

14.0 REPAIRS TO BUILDING

14.72S FINISHING

14.75 Repair to plaster of thickness 12 mm to 20 Sqm 300 670.95 201285

mm in patches of area 2.5 sqm and under,

including cutting the patch in proper shape,

raking out joints and preparing plastering the

wall surface with white cement based

polymer modified self curing mortar,

including disposal of rubbish, all complete as

per the direction of Engineer-In-Charge.

15.0 DISMANTLING AND DEMOLISHING

15.1S General

Demolishing cement concrete manually/ by

mechanical means including disposal of

material within 50 metres lead as per

direction of Engineer - in - charge.

(including equivalent design mix)

15.3 Demolishing R.C.C. work manually/ by cum 20 3551.25 71025

mechanical means including stacking of steel

63 bars and disposal of unserviceable material

within 50 metres lead as per direction of

Engineer - in- charge.

Demolishing brick work manually/ by

mechanical means including stacking of

15.7 serviceable material and disposal of

unserviceable material within 50 metres lead

as per direction of Engineer-in-charge.

Demolishing stone rubble masonry manually/

by mechanical means including stacking of

15.9 serviceable material and disposal of

unserviceable material within 50 metres lead

as per direction of Engineer-in-charge :

Dismantling doors, windows and clerestory

windows (steel or wood) shutter including

15.12 chowkhats, architrave, holdfasts etc.

complete and stacking within 50 metres lead

Dismantling tile work in floors and roofs laid

15.23 in cement mortar including stacking material

within 50 metres lead.

15.41 Dismantling cement asbestos or other hard Sqm 50 56.35 2817.5

board ceiling or partition walls including

68 stacking of serviceable materials and

disposal of unserviceable materials within 50

NAGPUR CR DIVISION-ENGINEERING/CENTRAL RLY

Dismantling G.I. pipes (external work)

including excavation and refilling trenches

after taking out the pipes, manually/ by

mechanical means including stacking of

pipes within 50 metres lead as per direction

of Engineer-in-charge :

15.51 Dismantling of road gully chamber of various Each 30 958.75 28762.5

sizes including C.I. grating with frame

including stacking of useful materials near

the site and disposal of unserviceable

materials within 50 metres lead including

refilling the excavated gap.

15.56 Dismantling old plaster or skirting raking out Sqm 250 54.65 13662.5

joints and cleaning the surface for plaster

including disposal of rubbish to the dumping

ground within 50 metres lead.

15.60 Disposal of building rubbish / malba / similar cum 1000 263.95 263950

unserviceable, dismantled or waste materials

by mechanical means, including loading,

72 transporting, unloading to approved

municipal dumping ground or as approved by

Engineer-in-charge, beyond 50 m initial lead,

for all leads including all lifts involved.

16.0 ROAD WORK

16.15S FENCING

16.19 Supplying at site Angle iron post & strut of Kg 1700 125.75 213775

required size including bottom to be split and

73 bent at right angle in opposite direction for

10 cm length and drilling holes upto 10 mm

dia. etc. complete.

16.25S SURFACE DRESSING

16.27 Surface dressing on old surface with hot Sqm 240 175.1 42024

bitumen of grade VG - 10 of approved quality

using 1.95 kg of bitumen per sqm with 1.50

74 cum of stone chippings 11.2 mm nominal

size per 100 sqm of road surface, including

consolidation with road roller of 6 to 8 tonne

capacity, etc. complete.

16.30S PREMIX CARPET

Providing and applying tack coat using

bitumen emulsion conforming to IS:8887,

16.31 using emulsion pressure distributer including

preparing the surface & cleaning with

mechanical broom.

16.31.1 With rapid setting bitumen emulsion

16.35 2.5 cm premix carpet surfacing with 3 cum of Sqm 2000 252.15 504300

stone chippings 10 mm nominal size per 100

sqm and bitumen emulsion (medium setting

76 min. 65% bitumen contents) complying with

IS : 8887, using 96 kg per cum of chippings

of road surface, including consolidation with

road roller etc complete .

16.40S SEAL COAT

16.40 Providing and laying seal coat of premixed Sqm 2000 88.55 177100

fine aggregate ( passing 2.36 mm and

retained on 180 micron sieve) with bitumen

using 128 kg of bitumen of grade VG - 10

bitumen per cum of fine aggregate and 0.60

cum of fine aggregate per 100 sqm of road

surface, including rolling and finishing with

road roller all complete.

16.47S PAINTING AREA/RUNWAY MARKING

NAGPUR CR DIVISION-ENGINEERING/CENTRAL RLY

Painting road surface marking with adequate

nos of coats to give uniform finish with ready

mixed road marking paint conforming to IS :

16.48 164, on bituminous surface in white/yellow

shade, including cleaning the surface of all

dirt, scales, oil, grease and foreign material

16.49S MISCELLANEOUS

Providing and fixing G.I. chain link fabric

fencing of required width in mesh size 50x50

mm including strengthening with 2 mm dia

wire or nuts, bolts and washers as required

complete as per the direction of Engineer-in-

17.0 SANITARY INSTALLATIONS

17.1S General

Providing and fixing white vitreous china

pedestal type water closet (European type

W.C. pan) with seat and lid, 10 litre low level

white P.V.C. flushing cistern, including flush

17.2 pipe, with manually controlled device (handle

lever), conforming to IS : 7231, with all

fittings and fixtures complete, including

cutting and making good the walls and floors

wherever required :

17.2.1 W.C. pan with ISI marked white solid plastic Each 20 6515.55 130311

Providing and fixing wash basin with C.I.

brackets, 15 mm C.P. brass pillar taps, 32

mm C.P. brass waste of standard pattern,

including painting of fittings and brackets,

cutting and making good the walls wherever

17.7.2 White Vitreous China Wash basin size Each 30 2226.35 66790.5

81 630x450 mm with a single 15 mm C.P. brass

Providing and fixing Stainless Steel A ISI 304

(18/8) kitchen sink as per IS:13983 with C.I.

brackets and stainless steel plug 40 mm,

including painting of fittings and brackets,

cutting and making good the walls wherever

17.10.2 Kitchen sink without drain board

Providing and fixing white vitreous china

water closet squatting pan (Indian type) :

17.16A Providing and fixing 8 mm dia C.P. / S.S. Jet Each 20 349.15 6983

with flexible tube upto 1 metre long with S.S.

85 triangular plate to European type W.C. of

quality and make as approved by Engineer -

Providing and fixing P.V.C. low level flushing

cistern with manually controlled device

(handle lever) conforming to IS : 7231, with

all fittings and fixtures complete.

Providing and fixing solid plastic seat with lid

for pedestal type W.C. pan complete :

NAGPUR CR DIVISION-ENGINEERING/CENTRAL RLY

17.22A Providing and fixing CP Brass 32mm size Each 30 1034.8 31044

88 Bottle Trap of approved quality & make and

as per the direction of Engineer-in-charge.

Providing and fixing P.V.C. waste pipe for

17.28 sink or wash basin including P.V.C. waste

fittings complete.

17.28.2 Flexible pipe

17.29 Providing and fixing 100 mm sand cast Iron Each 50 53.25 2662.5

grating for gully trap.

Providing and fixing soil, waste and vent

Cutting chases in brick masonry walls for

following diameter sand cast

iron/centrifugally cast (spun) iron pipes and

making good the same with cement concrete

17.61 1:3:6 ( 1 cement : 3 coarse sand :6 graded

stone aggregate 12.5 mm nominal size),

including necessary plaster and pointing in

cement mortar 1:4 (1 cement : 4 coarse

18.0 WATER SUPPLY

18.7S C.P.V.C. PIPES

Providing and fixing Chlorinated Polyvinyl

Chloride (CPVC) pipes, having thermal

stability for hot & cold water supply, and all

CPVC plain & brass threaded fittings,

including fixing the pipe with clamps at 1.00

m spacing. This includes jointing of pipes &

fittings with one step CPVC solvent cement

and testing of joints complete as per

direction of Engineer in Charge. ( Internal

work - Exposed on wall )

Providing and fixing Chlorinated Polyvinyl

Chloride (CPVC) pipes, having thermal

stability for hot & cold water supply,

including all CPVC plain & brass threaded

fittings and fixing the pipe with clamps at

1.00 m spacing. This includes jointing of

pipes & fittings with one step CPVC solvent

cement and the cost of cutting chases and

making good the same including testing of

joints complete as per direction of Engineer

in Charge. Concealed work, including cutting

chases and making good the walls etc.

Providing and fixing G.I. pipes complete with

18.12 G.I. fittings including trenching and refilling

etc. External work

Making connection of G.I. distribution branch

with G.I. main of following sizes by providing

and fixing tee, including cutting and

threading the pipe etc. complete :

NAGPUR CR DIVISION-ENGINEERING/CENTRAL RLY

18.14 Fixing water meter and stop cock in G.I. pipe Each 5 812.3 4061.5

line including cutting and threading the pipe

101 and making long screws etc. complete (cost

of water meter and stop cock to be paid

18.15S BRASS FITTINGS

Providing and fixing gun metal gate valve

18.17 with C.I. wheel of approved quality (screwed

Providing and fixing ball valve (brass) of

18.18 approved quality, High or low pressure, with

plastic floats complete :

Providing and fixing gun metal non- return

valve of approved quality (screwed end) :

18.19.1 25 mm nominal bore

Providing and fixing brass ferrule with C.I.

18.20 mouth cover including boring and tapping the

C.I. SLUICE VALVES/ FIRE HYDRANTS &

18.48 Providing and placing on terrace (at all floor Per Litre 20000 11 220000

levels) polyethylene water storage tank, IS :

12701 marked, with cover and suitable

109 locking arrangement and making necessary

holes for inlet, outlet and overflow pipes but

without fittings and the base support for

18.49S C.P. BRASS FITTINGS

Providing and fixing C.P. brass bib cock of

approved quality conforming to IS:8931 :

Providing and fixing C.P. brass stop cock

18.52 (concealed) of standard design and of

approved make conforming to IS:8931.

Providing and fixing C.P. brass angle valve

18.53 for basin mixer and geyser points of

approved quality conforming to IS:8931

18.54S PTMT FITTINGS

Providing and fixing PTMT bib cock of

approved quality and colour.

weighing not less than 99 gms

Providing and fixing PTMT grating of

approved quality and colour.

18.58.1 Circular type

18.59S AIR VALVE & WATER METER (BULK TYPE)

Providing and fixing C.I. double acting air

valve of approved quality with bolts, nuts,

18.59 rubber insertions etc. complete (The tail

pieces, tapers etc if required will be paid

NAGPUR CR DIVISION-ENGINEERING/CENTRAL RLY

19.0 DRAINAGE

19.1S STONE WARE PIPES AND FITTINGS

Providing, laying and jointing glazed

stoneware pipes class SP-1 with stiff mixture

19.1 of cement mortar in the proportion of 1:1 (1

cement : 1 fine sand) including testing of

joints etc. complete :

Providing and laying non-pressure NP2 class

(light duty) R.C.C. pipes with collars jointed

19.6 with stiff mixture of cement mortar in the

proportion of 1:2 (1 cement : 2 fine sand)

including testing of joints etc. complete :

Constructing brick masonry manhole in

cement mortar 1:4 ( 1 cement : 4 coarse

sand ) with R.C.C. top slab with 1:1.5:3 mix

(1 cement : 1.5 coarse sand (zone-III) : 3

graded stone aggregate 20 mm nominal

size),foundation concrete 1:4:8 mix (1

cement : 4 coarse sand (zone-III) : 8 graded

stone aggregate 40 mm nominal size), inside

plastering 12 mm thick with cement mortar

1:3 (1 cement : 3 coarse sand) finished with

floating coat of neat cement and making

channels in cement concrete1:2:4 (1 cement

: 2 coarse sand : 4 graded stone aggregate

20 mm nominal size) finished with a floating

coat of neat cement complete as per

standard design :

Inside size 90x80 cm and 45 cm deep

including C.I. cover with frame (light duty)

455x610 mm internal dimensions, total

weight of cover and frame to be not less than

38 kg (weight of cover 23 kg and weight of

19.7.1.1 With common burnt clay F.P.S. (non modular) Each 10 12770.55 127705.5

bricks of class designation 7.5

21.0 ALUMINIUM WORK

21.1S General

Providing and fixing aluminium work for

doors, windows, ventilators and partitions

with extruded built up standard tubular

sections/ appropriate Z sections and other

sections of approved make conforming to IS:

733 and IS: 1285, fixing with dash fasteners

of required dia and size, including necessary

filling up the gaps at junctions, i.e. at top,

bottom and sides with required EPDM rubber/

neoprene gasket etc. Aluminium sections

shall be smooth, rust free, straight, mitred

and jointed mechanically wherever required

including cleat angle, Aluminium snap

beading for glazing / panelling, C.P. brass /

stainless steel screws, all complete as per

architectural drawings and the directions of

Engineer-in-charge. (Glazing, panelling and

dash fasteners to be paid for separately) :

21.1.1 For fixed portion

21.1.1.2 Powder coated aluminium (minimum Kg 500 530.9 265450

thickness of powder coating 50 micron)

NAGPUR CR DIVISION-ENGINEERING/CENTRAL RLY

For shutters of doors, windows & ventilators

including providing and fixing hinges/ pivots

and making provision for fixing of fittings

wherever required including the cost of EPDM

rubber / neoprene gasket required (Fittings

shall be paid for separately)

21.1.2.2 Powder coated aluminium (minimum Kg 500 634.45 317225

thickness of powder coating 50 micron)

Providing and fixing 12 mm thick

prelaminated particle board flat pressed

three layer or graded wood particle board

conforming to IS: 12823 Grade l Type ll, in

21.2 panelling fixed in aluminium doors, windows

shutters and partition frames with C.P. brass

/ stainless steel screws etc. complete as per

architectural drawings and directions of

engineer-in-charge.

21.2.1 Pre-laminated particle board with decorative Sqm 50 1139.3 56965

123 lamination on one side and balancing

lamination on other side

Filling the gap in between aluminium frame &

adjacent RCC/ Brick/ Stone work by providing

weather silicon sealant over backer rod of

approved quality as per architectural

drawings and direction of Engineer-in-charge

Providing and fixing aluminium casement

windows fastener of required length for

aluminium windows with necessary screws

21.15.2 Powder coated minimum thickness 50 micron Each 100 97.95 9795

22.0 WATER PROOFING

22.1S General

Grading roof for water proofing treatment

126 sand : 4 graded stone aggregate 20 mm

Providing and applying integral crystalline

slurry of hydrophilic in nature for

waterproofing treatment to the RCC

structures like retaining walls of the

basement, water tanks, roof slabs, podiums,

reservoir, sewage & water treatment plant,

tunnels / subway and bridge deck etc.,

prepared by mixing in the ratio of 5 : 2 (5

parts integral crystalline slurry : 2 parts

water) for vertical surfaces and 3 : 1 (3 parts

integral crystalline slurry : 1 part water) for

horizontal surfaces and applying the same

from negative (internal) side with the help of

synthetic fiber brush. The material shall meet

the requirements as specified in ACI-212-3R-

2010 i.e. by reducing permeability of

concrete by more than 90% compared with

control concrete as per DIN 1048 and

resistant to 16 bar hydrostatic pressure on

negative side. The crystalline slurry shall be

capable of self-healing of cracks up to a

width of 0.50 mm. The work shall be carried

out all complete as per specification and the

direction of the engineer-in-charge. The

product performance shall carry guarantee

for 10 years against any leakage.

22.23.1 For vertical surface two coats @ 0.70 kg per Sqm 200 472.9 94580

NAGPUR CR DIVISION-ENGINEERING/CENTRAL RLY

22.23.2 For horizontal surface one coat @1.10 kg per Sqm 500 362.8 181400

22.23A Providing & Applying polymer modified, Sqm 50 447.35 22367.5

flexible cementitious negative side

waterproofing coating with elastic

waterproofing polymers on interior wall

plaster surface in three coats @14.35 kg /10

sqm. one coat of self priming of cementitious

waterproofing polymer(dilution with water in

the ratio of 1:1) and two coats of

cementitious waterproofing polymer (dilution

with water in the ratio of 3:1 ) after scrapping

and properly cleaning the surface to remove

pre-existing paint film & loose particles till

plaster is visible, complete in all respect as

per the direction of Engineer-in-Charge.

23.0 RAIN WATER HARVESTING & TUBEWELLS

23.1S General

23.9 Providing and fixing factory made precast Each 20 1399.95 27999

RCC perforated drain covers, having concrete

of strength not less than M-25, of size 1000 x

450x50 mm, reinforced with 8 mm dia four

nos longitudinal & 9 nos cross sectional

T.M.T. hoop bars, including providing 50 mm

dia perforations @ 100 to 125 mm c/c,

including providing edge binding with M.S.

flats of size 50 mm x 1.6 mm complete, all as

per direction of Engineer-in-charge.

26.0 NEW TECHNOLOGIES AND MATERIALS

26.41S NEW TECHNOLOGY ITEMS

26.60 Water proofing treatment of RCC sunshade Sqm 11 136.45 1500.95

w i t h Zycosil/equivalent water proofing

Solution (1 litre of Zycosil/equivalent & 20

litres of water stirred first & 2 litres of

131 Zycoprime/equivalent added and stirred

(total 23 litres)) till it meets the saturation

level and testing as per RILEM or by water

drops test in which water drops do not absorb

but drops remain or rolls.

Schedule 10-PART (B)(2): Nagpur Improvement to Roof, Drainage system, water supply pipe line,

Kitchen Otta, Road Pathway, flooring, Plastering at Guard line Railway Colony.

Item- 01 NS ITEM

S No. Item No Description of Item Unit Qty Rate Amount

1 01 Hiring of machinery for minor miscellaneous Hour 50.00 752.64 37632.00

works for short duration including

operator/driver, fuel, lubricants and

consumable. The contractor shall arrange all

statutory permits as required by rules

andregulations prevailing in the area of work.

Payment shall be made foractual working

hours at site. 211201 JCB Backhoe Loaders

3DX Plus or similar with minimum 1.10

cumbucket capacity. (USSOR-2021 ITEM

Schedule 11-PART (C) (i): Provision of Approach road and two-wheeler parking and repairs to C&W

staff room near PF No. 7, beside booster pump house under ADEN/HQ/NGP.

Item- 01 MS Item (DSR-2023)

S No. Item No Description of Item Unit Qty Rate Amount

2.0 EARTH WORK

2.1S General

NAGPUR CR DIVISION-ENGINEERING/CENTRAL RLY

Earth work in excavation by mechanical

means (Hydraulic excavator)/manual means

over areas (exceeding 30 cm in depth, 1.5 m

2.6 in width as well as 10 sqm on plan) including

getting out and disposal of excavated earth

lead upto 50 m and for all lift, as directed by

Engineer-in-charge.

4.0 CONCRETE WORK

4.1S CEMENT CONCRETE (CAST IN SITU)

Providing and laying in position cement

concrete of specified grade excluding the

cost of centering and shuttering - All work up

to plinth level :

derived from natural sources : 4 graded stone

aggregate 20 mm nominal size derived from

natural sources)

5.0 REINFORCEMENT CEMENT CONCRETE

5.9S FORM WORK

Centering and shuttering including strutting,

propping etc. and removal of form for

5.9.1 Foundations, footings, bases of columns, etc. Sqm 35 392.15 13725.25

for mass concrete

5.22S STEEL REINFORCEMENT

Steel reinforcement for R.C.C. work including

straightening, cutting, bending, placing in

position and binding all complete above

5.22A.6 Thermo-Mechanically Treated bars of grade Kg 3000 107.85 323550

Fe-500D or more.

5.33S DESIGN MIX CONCRETE

Providing and laying in position ready mixed

or site batched design mix cement concrete

for reinforced cement concrete work; using

coarse aggregate and fine aggregate derived

from natural sources, Portland Pozzolana /

Ordinary Portland /Portland Slag cement,

admixtures in recommended proportions as

per IS: 9103 to accelerate / retard setting of

concrete, to improve durability and

w o r k a b i l i t y without impairing strength;

including pumping of concrete to site of

laying, curing, carriage for all leads; but

excluding the cost of centering, shuttering,

finishing and reinforcement as per direction

of the engineer-in-charge, for the following

grades of concrete.:

5.33.1 All works upto plinth level

5.33.1.2 Concrete of M30 grade with minimum cement cum 67 9655.7 646931.9

content of 350 kg /cum

6.0 MASONRY WORK

6.1S General

Brick work with common burnt clay modular

6.2 bricks of class designation 7.5 in foundation

6.26S EXPOSED BRICK WALL

NAGPUR CR DIVISION-ENGINEERING/CENTRAL RLY

6.47 Providing and laying Autoclaved Aerated cum 8 8333.65 66669.2

Concrete (AAC) blocks masonry with 150 mm

to 300 mm thick with Grade -1 AAC blocks of

density 551 to 650 kg/cum conforming to IS:

2185 (Part 3) in super structure above plinth

7 level up to floor V level with RCC band at sill

level and lintel level with approved block

laying polymer modified adhesive mortar all

complete as per direction of Engineer-in-

Charge. (The payment of RCC band and

reinforcement shall be made for separately).

8.0 CLADDING WORK

8.1S General

Providing and fixing 18 mm thick gang saw

cut, mirror polished, premoulded and

prepolished, machine cut for kitchen

platforms, vanity counters, window sills,

facias and similar locations of required size,

approved shade, colour and texture laid over

20 mm thick base cement mortar 1:4 (1

cement : 4 coarse sand), joints treated with

white cement, mixed with matching pigment,

epoxy touch ups, including rubbing, curing,

moulding and polishing to edges to give high

gloss finish etc. complete at all levels

Granite stone slab colour black, Cherry/Ruby

Providing edge moulding to 18 mm thick

marble stone counters, Vanities etc.,

8.3 including machine polishing to edge to give

high gloss finish etc. complete as per design

approved by Engineer-in-Charge.

8.20S STONE WORK DRY CLADDING

8.31 Providing and fixing Ist quality ceramic Sqm 40 1267.95 50718

glazed wall tiles conforming to IS: 15622

(thickness to be specified by the

manufacturer), of approved make, in all

colours, shades except burgundy, bottle

green, black of any size as approved by

11 Engineer-in-Charge, in skirting, risers of steps

and dados, over 12 mm thick bed of cement

mortar 1:3 (1 cement : 3 coarse sand) and

jointing with grey cement slurry @ 3.3kg per

sqm, including pointing in white cement

mixed with pigment of matching shade

9.0 WOOD AND P.V.C. WORK

9.1S FRAMES AND TRUSSES

Providing wood work in frames of doors,

windows, clerestory windows and other

frames, wrought framed and fixed in position

with hold fast lugs or with dash fasteners of

required dia & length (hold fast lugs or dash

fastener shall be paid for separately).

Providing and fixing panelling or panelling

and glazing in panelled or panelled and

glazed shutters for doors, windows and

clerestory windows (Area of opening for

panel inserts excluding portion inside

grooves or rebates to be measured).

Panelling for panelled or panelled and glazed

shutters 25 mm to 40 mm thick :

9.7.7 Float glass panes

NAGPUR CR DIVISION-ENGINEERING/CENTRAL RLY

9.7.7.2 5.0 mm thick glass panes (weight not less Sqm 12 2600.45 31205.4

than 12.50 kg/sqm).

Providing and fixing ISI marked flush door

shutters conforming to IS : 2202 (Part I)

decorative type, core of block board

9.20 construction with frame of 1st class hard

wood and well matched teak 3 ply veneering

with vertical grains or cross bands and face

veneers on both faces of shutters.

9.20.2 30 mm thick including ISI marked Stainless Sqm 8 3167.95 25343.6

Steel butt hinges with necessary screws

9.40S MISCELLANEOUS-WOOD WORK

Providing and fixing nickel plated M.S. pipe

curtain rods with nickel plated brackets :

Providing and fixing M.S. grills of required

pattern in frames of windows etc. with M.S.

9.48 flats, square or round bars etc. including

priming coat with approved steel primer all

COPER OXIDISED MILD STEEL FITTINGS

(COPPER OXIDISED AS PER IS: 1378)

Providing and fixing ISI marked oxidised M.S.

9.62 sliding door bolts with nuts and screws etc.

complete (Copper oxidised as per IS 1378)

Providing and fixing ISI marked oxidised M.S.

tower bolt black finish, (Barrel type) with

necessary screws etc. complete (Copper

oxidised as per IS 1378)

9.64 Providing and fixing ISI marked 85x42 mm Each 4 122.15 488.6

oxidised M.S. pull bolt lock conforming to IS :

19 7534 with necessary screws bolts, nut and

washers etc. complete (Copper oxidised as

Providing and fixing ISI marked oxidised M.S.

door latches conforming to IS:5930 with

screws etc. complete (Copper oxidised as per

ANODISED ALUMINIUM FITTINGS (ALL

FITTINGS SHALL BE ISI MARKED)

Providing and fixing ISI marked aluminium

butt hinges anodised (anodic coating not less

9.95 than grade AC 10 as per IS: 1868)

transparent or dyed to required colour or

shade with necessary screws etc.complete:

Providing and fixing aluminium sliding door

bolts, ISI marked anodised (anodic coating

9.96 not less than grade AC 10 as per IS : 1868),

transparent or dyed to required colour or

shade, with nuts and screws etc. complete :

Providing and fixing aluminium tower bolts,

ISI marked, anodised (anodic coating not less

9.97 than grade AC 10 as per IS : 1868 )

transparent or dyed to required colour or

shade, with necessary screws etc. complete :

NAGPUR CR DIVISION-ENGINEERING/CENTRAL RLY

Providing and fixing aluminium handles, ISI

marked, anodised (anodic coating not less

9.100 than grade AC 10 as per IS : 1868)

transparent or dyed to required colour or

shade, with necessary screws etc. complete :

9.105S GYPSUM BOARD PARTITIONS

9.119 Providing and fixing factory made P.V.C. door Metre 8 492.7 3941.6

frame of size 50x47 mm with a wall thickness

of 5 mm, made out of extruded 5 mm rigid

PVC foam sheet, mitred at corners and joined

with 2 Nos of 150 mm long brackets of 15x15

mm M.S. square tube, the vertical door frame

profiles to be reinforced with 19x19 mm M.S.

square tube of 19 gauge, EPDM rubber

gasket weather seal to be provided through

out the frame. The door frame to be fixed to

the wall using M.S. screws of 65/100 mm

size, complete as per manufacturer's

specification and direction of Engineer- in-

Providing and fixing factory made panel PVC

door shutter consisting of frame made out of

M.S. tubes of 19 gauge thickness and size of

19 mm x 19 mm for styles and 15x15 mm for

top & bottom rails. M.S. frame shall have a

coat of steel primers of approved make and

manufacture. M.S. frame covered with 5 mm

thick heat moulded PVC 'C' channel of size

30 mm thickness, 70 mm width out of which

50 mm shall be flat and 20 mm shall be

tapered in 45 degree angle on both side

forming styles and 5 mm thick, 95 mm wide

PVC sheet out of which 75mm shall be flat

and 20 mm shall be tapered in 45 degree on

the inner side to form top and bottom rail

and 115 mm wide PVC sheet out of which 75

9.120 mm shall be flat and 20 mm shall be tapered

on both sides to form lock rail. Top, bottom

and lock rails shall be provided both side of

the panel. 10 mm (5 mm x 2 ) thick, 20 mm

wide cross PVC sheet be provided as gap

insert for top rail & bottom rail, panelling of 5

mm thick both side PVC sheet to be fitted in

the M.S. frame welded/ sealed to the styles &

rails with 7 mm (5 mm+2 mm) thick x 15 mm

wide PVC sheet beading on inner side, and

joined together with solvent cement

adhesive. An additional 5 mm thick PVC strip

of 20 mm width is to be stuck on the interior

side of the 'C' Channel using PVC solvent

adhesive etc. complete as per direction of

Engineer-in-charge, manufacturer's

specification & drawing.

NAGPUR CR DIVISION-ENGINEERING/CENTRAL RLY

Providing and fixing factory made uPVC

glazed/wire mesh windows/ doors comprising

of lead free uPVC multi-chambered frame,

sash and mullion/coupler (where ever

required) extruded profiles having minimum

wall thickness of 1.70 mm for Series R1 and

R2 profiles and 2.10 mm for Series R3 and

R4 profiles conforming to EN: 12608 in any

shape, colour and design duly reinforced with

galvanized mild steel section made of

required shape & size as per CPWD

Specification, uPVC extruded glazing beads,

interlocks and Inline sash adaptor (where

ever required) of appropriate dimension,

EPDM gasket, hardware, SS 304 grade

fasteners of minimum 8 mm dia with

countersunk head, comprising of matching

polyamide PA6 grade sleeve for fixing frame

to finished wall as per IS 1367 : Part 1 to 14,

plastic packers, plastic caps and necessary

stainless steel screws etc. Profile of frame,

sash & mullion (if required) shall be mitred

cut and fusion welded/mechanically jointed

duly sealed at all corners, including drilling of

holes for fixing hardware and drainage of

water etc. After fixing frame the gap

between frame and adjacent finished wall

shall be filled with weather proof silicon

sealant over backer rod of approved size and

quality, all complete as per approved

drawing conforming to CPWD specification &

direction of Engineer-in-Charge. Section of

steel reinforcement and cross sections of

uPVC profiles to be as per design approved

by Engineer-in-Charge. Wire mesh / Glazing

of plain/ toughened/ laminated/ double glass

unit with / without high performance coatings

as per design requirements and conforming

to IS: 3548 & IS: 16231 shall be paid

Two and half track three panels sliding

window with two glazed & one wire mesh

9.147.A3 panels with Aluminium channel for roller

track, wool pile, nylon rollers with SS 304

9.147.A3.1 Using R2 series with frame (65 mm & above) Sqm 12 9933.4 119200.8

x (40 mm & above) & glazed sash (25 mm &

above) x (50 mm & above) & fly screen sash

(18 mm & above) x (40 mm & above) with

zinc alloy (zamak) powder coated touch locks

with hook (Height upto 1.2 metre).

Providing and fixing stainless steel fancy

handle of approved make fixed with SS

screws etc. complete as per direction of

Engineer-in-charge.

10.0 STEEL WORK

10.1S General

10.2 Structural steel work riveted, bolted or Kg 800 133.7 106960

welded in built up sections, trusses and

29 framed work, including cutting, hoisting,

fixing in position and applying a priming coat

of approved steel primer all complete.

Steel work in built up tubular (round, square

or rectangular hollow tubes etc.) trusses etc.,

including cutting, hoisting, fixing in position

and applying a priming coat of approved

steel primer, including welding and bolted

with special shaped washers etc. complete.

NAGPUR CR DIVISION-ENGINEERING/CENTRAL RLY

11.0 FLOORING

11.37S CERAMIC GLAZED TILES

11.37 Providing and laying Ceramic glazed floor Sqm 10 1096.55 10965.5

tiles of size 300x300 mm (thickness to be

specified by the manufacturer) of 1st quality

conforming to IS : 15622 of approved make

in colours such as White, Ivory, Grey, Fume

31 Red Brown, laid on 20 mm thick cement

mortar 1:4 (1 Cement : 4 Coarse sand),

Jointing with grey cement slurry @ 3.3

kg/sqm including pointing the joints with

white cement and matching pigment etc.,

11.41S VITRIFIED FLOOR TILES

Providing and laying vitrified floor tiles in

different sizes (thickness to be specified by

the manufacturer) with water absorption less

than 0.08% and conforming to IS: 15622, of

approved make, in all colours and shades,

laid on 20mm thick cement mortar 1:4 (1

cement : 4 coarse sand), jointing with grey

cement slurry @ 3.3 kg/ sqm including

grouting the joints with white cement and

matching pigments etc., complete.

12.0 ROOFING

12.1S SHEET ROOFING

12.11 Extra for providing and fixing wind ties of 40x Metre 90 195.6 17604

6 mm flat iron section.

12.37S RAIN WATER SPOUT AND PIPE

Providing and fixing on wall face

unplasticised Rigid PVC rain water pipes

conforming to IS : 13592 Type A, including

jointing with seal ring conforming to IS :

5382, leaving 10 mm gap for thermal

expansion, (i) Single socketed pipes.

Providing and fixing on wall face

unplasticised - PVC moulded fittings/

accessories for unplasticised Rigid PVC rain

12.42 water pipes conforming to IS : 13592 Type A,

including jointing with seal ring conforming

to IS : 5382, leaving 10 mm gap for thermal

12.42.5 Bend 87.5 degree

NAGPUR CR DIVISION-ENGINEERING/CENTRAL RLY

12.50 Providing and fixing precoated galvanised Sqm 140 738.65 103411

iron profile sheets (size, shape and pitch of

corrugation as approved by Engineer-in-

charge) of total coated thickness 0.50 mm

(base metal of minimum 0.45 mm thickness

with total coating thickness of 0.05 mm) with

zinc coating 120 grams per sqm as per IS:

277, in 240 mpa steel grade, 5-7 microns

epoxy primer on both side of the sheet and

polyester top coat 15-18 microns. Sheet

36 should have protective guard film of 25

microns minimum to avoid scratches during

transportation and should be supplied in

single length upto 12 metre or as desired by

Engineer-in-charge. The sheet shall be fixed

using self drilling /self tapping screws of size

(5.5x 55 mm) with EPDM seal, complete upto

any pitch in horizontal/ vertical or curved

surfaces, excluding the cost of purlins, rafters

and trusses and including cutting to size and

shape wherever required.

Providing and fixing precoated galvanised

steel sheet roofing accessories of total

coated thickness 0.50 mm (base metal of

minimum 0.45 mm thickness with total

coating thickness of 0.05 mm) with Zinc

coating 120 grams per sqm as per IS: 277, in

240 mpa steel grade, 5-7 microns epoxy

primer on both side of the sheet and

polyester top coat 15-18 microns using self

drilling/ self tapping screws complete :

13.0 FINISHING

13.1S CEMENT PLASTER (IN FINE SAND)

13.1 12 mm cement plaster of mix :

15 mm cement plaster on the rough side of

single or half brick wall of mix :

13.44S EXTERIOR FINISHING

Finishing with Deluxe Multi surface paint

13.48 system for interiors and exteriors using

Primer as per manufacturers specifications :

13.48.2 Painting wood work with Deluxe Multi Surface Sqm 20 176.25 3525

Paint of required shade. Two or more coat

40 applied @ 0.90 ltr/10 sqm over an under coat

of primer applied @0.75 ltr/10 sqm of

approved brand and manufacture

13.48.3 Painting Steel work with Deluxe Multi Surface Sqm 100 170.7 17070

Paint to give an even shade. Two or more

41 coat applied @ 0.90 ltr/10 sqm over an under

coat of primer applied @ 0.80 ltr/10 sqm of

approved brand and manufacture

Wall painting with premium acrylic emulsion

paint of interior grade, having VOC (Volatile

Organic Compound ) content less than 50

13.83 grams/ litre of approved brand and

manufacture, including applying additional

coats wherever required to achieve even

shade and colour.

Applying priming coats with primer of

13.85 approved brand and manufacture, having low

VOC (Volatile Organic Compound ) content.

13.85.3 With water thinnable cement primer on wall Sqm 600 73.95 44370

43 surface having VOC content less than 50

NAGPUR CR DIVISION-ENGINEERING/CENTRAL RLY

13.88 Removing white or colour wash by scrapping Sqm 600 19.75 11850

and sand papering and preparing the surface

smooth including necessary repairs to

scratches etc. complete

Finishing walls with Acrylic Smooth exterior

paint of required shade :

13.111.1 Old work (Two or more coat applied @ 1.67 Sqm 200 120.75 24150

ltr/ 10 sqm) on existing cement paint surface

14.0 REPAIRS TO BUILDING

14.72S FINISHING

14.75 Repair to plaster of thickness 12 mm to 20 Sqm 100 670.95 67095

mm in patches of area 2.5 sqm and under,

including cutting the patch in proper shape,

raking out joints and preparing plastering the

wall surface with white cement based

polymer modified self curing mortar,

including disposal of rubbish, all complete as

per the direction of Engineer-In-Charge.

15.0 DISMANTLING AND DEMOLISHING

15.1S General

Demolishing brick work manually/ by

mechanical means including stacking of

15.7 serviceable material and disposal of

unserviceable material within 50 metres lead

as per direction of Engineer-in-charge.

Dismantling doors, windows and clerestory

windows (steel or wood) shutter including

15.12 chowkhats, architrave, holdfasts etc.

complete and stacking within 50 metres lead

15.18 Dismantling steel work in built up sections in Kg 25 5.65 141.25

angles, tees, flats and channels including all

49 gusset plates, bolts, nuts, cutting rivets,

welding etc. including dismembering and

stacking within 50 metres lead.

Dismantling roofing including ridges, hips,

15.28 valleys and gutters etc., and stacking the

material within 50 metres lead of:

15.56 Dismantling old plaster or skirting raking out Sqm 30 54.65 1639.5

joints and cleaning the surface for plaster

including disposal of rubbish to the dumping

ground within 50 metres lead.

15.60 Disposal of building rubbish / malba / similar cum 300 263.95 79185

unserviceable, dismantled or waste materials

by mechanical means, including loading,

52 transporting, unloading to approved

municipal dumping ground or as approved by

Engineer-in-charge, beyond 50 m initial lead,

for all leads including all lifts involved.

16.0 ROAD WORK

16.15S FENCING

16.19 Supplying at site Angle iron post & strut of Kg 280 125.75 35210

required size including bottom to be split and

53 bent at right angle in opposite direction for

10 cm length and drilling holes upto 10 mm

dia. etc. complete.

16.49S MISCELLANEOUS

NAGPUR CR DIVISION-ENGINEERING/CENTRAL RLY

Providing and fixing G.I. chain link fabric

fencing of required width in mesh size 50x50

mm including strengthening with 2 mm dia

wire or nuts, bolts and washers as required

complete as per the direction of Engineer-in-

Providing and laying factory made chamfered

edge Cement Concrete paver blocks in

footpath, parks, lawns, drive ways or light

traffic parking etc, of required strength,

thickness & size/ shape, made by table

vibratory method using PU mould, laid in

required colour & pattern over 50mm thick

compacted bed of sand, compacting and

proper embedding/laying of inter locking

paver blocks into the sand bedding layer

through vibratory compaction by using plate

vibrator, filling the joints with sand and

cutting of paver blocks as per required size

and pattern, finishing and sweeping extra

sand. complete all as per direction of

Engineer-in-Charge.

16.91.1 60mm thick cement concrete paver block of Sqm 180 1045.65 188217

55 M-35 grade with approved colour, design &

17.0 SANITARY INSTALLATIONS

17.1S General

Providing and fixing wash basin with C.I.

brackets, 15 mm C.P. brass pillar taps, 32

mm C.P. brass waste of standard pattern,

including painting of fittings and brackets,

cutting and making good the walls wherever

17.7.2 White Vitreous China Wash basin size Each 1 2226.35 2226.35

56 630x450 mm with a single 15 mm C.P. brass

Providing and fixing P.V.C. low level flushing

cistern with manually controlled device

(handle lever) conforming to IS : 7231, with

all fittings and fixtures complete.

17.22A Providing and fixing CP Brass 32mm size Each 1 1034.8 1034.8

58 Bottle Trap of approved quality & make and

as per the direction of Engineer-in-charge.

17.23 Providing and fixing white vitreous china flat Each 2 1648.95 3297.9

back or wall corner type lipped front urinal

basin of 430x260x350 mm or 340x410x265

mm sizes respectively.

Providing and fixing P.V.C. waste pipe for

17.28 sink or wash basin including P.V.C. waste

fittings complete.

17.28.2 Flexible pipe

17.34 Providing and fixing toilet paper holder :

Cutting chases in brick masonry walls for

following diameter sand cast

iron/centrifugally cast (spun) iron pipes and

making good the same with cement concrete

17.61 1:3:6 ( 1 cement : 3 coarse sand :6 graded

stone aggregate 12.5 mm nominal size),

including necessary plaster and pointing in

cement mortar 1:4 (1 cement : 4 coarse

NAGPUR CR DIVISION-ENGINEERING/CENTRAL RLY

Providing and fixing PTMT towel rail complete

with brackets fixed to wooden cleats with CP

brass screws with concealed fittings

arrangement of approved quality and colour.

17.73.2 600 mm long towel rail with total length of Each 1 708.95 708.95

63 645 mm, width 78 mm and effective height

of 88 mm, weighing not less than 190 gms.

17.78 Providing and fixing white vitreous china Each 1 14999.15 14999.15

extended wall mounting water closet of size

780x370x690 mm of approved shape

including providing & fixing white vitreous

64 china cistern with dual flush fitting, of

flushing capacity 3 litre/ 6 litre (adjustable to

4 litre/ 8 litres), including seat cover, and

cistern fittings, nuts, bolts and gasket etc

18.0 WATER SUPPLY

18.7S C.P.V.C. PIPES

Providing and fixing Chlorinated Polyvinyl

Chloride (CPVC) pipes, having thermal

stability for hot & cold water supply, and all

CPVC plain & brass threaded fittings,

including fixing the pipe with clamps at 1.00

m spacing. This includes jointing of pipes &

fittings with one step CPVC solvent cement

and testing of joints complete as per

direction of Engineer in Charge. ( Internal

work - Exposed on wall )

Providing and fixing Chlorinated Polyvinyl

Chloride (CPVC) pipes, having thermal

stability for hot & cold water supply,

including all CPVC plain & brass threaded

fittings and fixing the pipe with clamps at

1.00 m spacing. This includes jointing of

pipes & fittings with one step CPVC solvent

cement and the cost of cutting chases and

making good the same including testing of

joints complete as per direction of Engineer

in Charge. Concealed work, including cutting

chases and making good the walls etc.

18.15S BRASS FITTINGS

Providing and fixing gun metal gate valve

18.17 with C.I. wheel of approved quality (screwed

Providing and fixing ball valve (brass) of

18.18 approved quality, High or low pressure, with

plastic floats complete :

Providing and fixing gun metal non- return

valve of approved quality (screwed end) :

18.19.1 25 mm nominal bore

C.I. SLUICE VALVES/ FIRE HYDRANTS &

NAGPUR CR DIVISION-ENGINEERING/CENTRAL RLY

Constructing masonry Chamber 60x60x75

cm inside, in brick work in cement mortar 1:4

(1 cement : 4 coarse sand) for sluice valve,

with C.I.surface box 100 mm top diameter,

160 mm bottom diameter and 180 mm deep

( inside) with chained lid and RCC top slab

1:1.5:3 mix (1 cement : 1.5 coarse sand : 3

18.33 graded stone aggregate 20 mm nominal size

) including necessary excavation, foundation

concrete 1:5:10 (1 cement : 5 fine sand: 10

graded stone aggregate 40 mm nominal

size) and inside plastering with cement

mortar 1:3 (1 cement : 3 coarse sand) 12 mm

thick, finished with a floating coat of neat

cement complete as per standard design :

18.33.1 With common burnt clay F.P.S.(non modular) Each 2 10862.4 21724.8

bricks of class designation 7.5

18.48 Providing and placing on terrace (at all floor Per Litre 1000 11 11000

levels) polyethylene water storage tank, IS :

12701 marked, with cover and suitable

72 locking arrangement and making necessary

holes for inlet, outlet and overflow pipes but

without fittings and the base support for

18.49S C.P. BRASS FITTINGS

Providing and fixing C.P. brass bib cock of

approved quality conforming to IS:8931 :

Providing and fixing C.P. brass stop cock

18.52 (concealed) of standard design and of

approved make conforming to IS:8931.

Providing and fixing C.P. brass angle valve

18.53 for basin mixer and geyser points of

approved quality conforming to IS:8931

18.54S PTMT FITTINGS

Providing and fixing PTMT grating of

approved quality and colour.

18.58.1 Circular type

21.0 ALUMINIUM WORK

21.1S General

Providing and fixing aluminium work for

doors, windows, ventilators and partitions

with extruded built up standard tubular

sections/ appropriate Z sections and other

sections of approved make conforming to IS:

733 and IS: 1285, fixing with dash fasteners

of required dia and size, including necessary

filling up the gaps at junctions, i.e. at top,

bottom and sides with required EPDM rubber/

neoprene gasket etc. Aluminium sections

shall be smooth, rust free, straight, mitred

and jointed mechanically wherever required

including cleat angle, Aluminium snap

beading for glazing / panelling, C.P. brass /

stainless steel screws, all complete as per

architectural drawings and the directions of

Engineer-in-charge. (Glazing, panelling and

dash fasteners to be paid for separately) :

21.1.1 For fixed portion

21.1.1.2 Powder coated aluminium (minimum Kg 16 530.9 8494.4

thickness of powder coating 50 micron)

NAGPUR CR DIVISION-ENGINEERING/CENTRAL RLY

For shutters of doors, windows & ventilators

including providing and fixing hinges/ pivots

and making provision for fixing of fittings

wherever required including the cost of EPDM

rubber / neoprene gasket required (Fittings

shall be paid for separately)

thickness of powder coating 50 micron)

Filling the gap in between aluminium frame &

adjacent RCC/ Brick/ Stone work by providing

weather silicon sealant over backer rod of

approved quality as per architectural

drawings and direction of Engineer-in-charge

Schedule 12-PART (C) (ii): Provision of Approach road and two-wheeler parking and repairs to C&W

staff room near PF No. 7, beside booster pump house under ADEN/HQ/NGP.

Item- 01 NS ITEM

S No. Item No Description of Item Unit Qty Rate Amount

waste and vent pipes including jointing and

cost of spun yarn and sand etc. complete

(USSOR 2011 Item no. 154010)

Schedule 13-PART (C) (iii): Provision of Approach road and two-wheeler parking and repairs to C&W

staff room near PF No. 7, beside booster pump house under ADEN/HQ/NGP.

Item- 01 NS ITEM

S No. Item No Description of Item Unit Qty Rate Amount

1 1 Providing and fixing two way bib cock Numbers 1.00 2900.00 2900.00

chromium plated (toilet bib) of jaquar make

code no. 041/Marcseries no. MOR-bib cock

chromium plated (toilet bib) contractor's

material, labour, tools & plants complete with

all lead & lift.

2 2 Providing and fixing jet spray of jaguar make Numbers 1.00 2800.00 2800.00

code no. ALD-CHR 593 or similar including

flexible pipe and wall bracket as approved by

Engineer-in-charge with all contractor's

labour, material, tools and plants etc

complete with all lead and lift.