Renovation of Sitting Space at CSIR NIScPR First Floor NSL SV Marg New Delhi

Amount

Dismantling aluminium/wooden/gypsum partitions,false ceiling, doors, windows, fixed glazing etc. including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge.

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : (a) Of area 3 sq. metres and below

Dismantling Vinyle/PVC flooring in floors including stacking material within 50 metres lead. (a) For thickness of tiles upto 5 mm

Providing and laying Vinyl PVC flooring 4 mm thick in floor with different sizes, designs & patterns and colours as direction by Engineer In charge (Basic Rate of items approx. 50.0/S.ft)

Providing and laying Double charge Vitrified tiles in floor of size 1000 x 1000 mm (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, Fixing glazed/ Ceramic/ Vitrified floor tiles with cement based high polymer modified quick-set tile adhesive (Water based) conforming to IS: 15477, in average 3mm thickness. including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only. Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. (a) Size of Tile 1000 x 1000 mm

Providing and laying Double Charged Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. (a) Size of Tile 1000 x 1000 mm

Providing and fixing partition upto ceiling height consisting of G .I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G .I. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete.

75mm overall thickness partition with 12.5 mm thick double skin tapered edged plain Gypsum plaster board conforming to IS: 2095: (p art I): 201 1 (Board with BIS certification marks)

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: (a) 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

(a) For fixed portion Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron)

(b) For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) (a) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): (a) With float glass panes of 5.0 mm thickness

S/fixing Frosted glass films on glass partitions/doors any design copmlete as per direction of Engineer-in- Charge

Filling the gap in between aluminium/ stone/ wood frame and adjacent RCC/ Brick/ Stone/ wood/ Ceramic/ Gypsum work by providing weather/structural non sag elastomeric PU sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete, complying to ASTM C920, DIN 18540-F & ISO 11600 (a) Upto 5 mm depth and 5 mm width

Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etc. complete: 75x63x3.2 mm

(a) 100x75x4 mm for Aluminium Doors

(b) 75x63x3.2 mm for Storage/Over Head Storage

(c) 75x45x3.2 mm for Window

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. (a) Twin rubber stopper

Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complet

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : (a) 250x16 mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete. (a) 100 mm

Providing and fixing magnetic catcher of approved quality in cupboard /ward robe shutters, including fixing with necessary screws etc. complete Double strip (horizontal type)

Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete. 50 mm

Providing and fixing powder coated telescopic drawer channels 300 mm long with necessary screws etc. complete as per directions of Engineerin- charge.

Providing and fixing specified wood frame work consisting of battens 50x25mm fixed with rawl plug and drilling necessary holes for rawl plug etc. including priming coat complete. (a) Kiln seasoned and chemically treated hollock wood

Providing and fixing in wall lining medium density fibre board IS: 14587:1998 marked, Pre-laminated one side decorative lamination and other side balancing lamination, with necessary fixing arrangement and screws etc. complete.

(a) 12 mm thick.

(b) 25 mm thick.

Providing and fixing 6mm thick Pinup Board with backing support and suitable cloth shade all complete as per direction of Engineer-in-charge.

Providing and fixing 6mm thick writing Board with backing complete as per direction of Engineer-in-charge.

Providing and fixing 2mm thick 12 to 25 mm wide PVC edge binding tape of approved quality for cupboard/wardrobe shutters including necessary synthetic resin hot pressed to edges on binding machine etc. complete as per directions of Engineer- in-charge.

Providing and fixing 2nd class teak wood lipping/ moulded beading or taj beading of requeired sizes fixed with wooden adhesive of approved quality and screws/nails on the edges of the Pre-laminated particle board as per direction of Engineer-in-charge.

Providing and fixing Pre-laminated medium density fibre board IS: 14587:1998 marked, with one side decorative lamination other side balancing lamination Grade-I(exterior grade) in shelves with screws and fittings wherever required, edges to be sealed with PVC edge bending tape 2.00 mm thick of approved brand (fittings to be paid separately). (a) Pre-laminated with decorative lamination one side and other side balancing lamination exterior Grade - I MDF Board 18 mm thick confirming to IS:14587

Providing and fixing flat pressed 3 layer particle board medium density exterior grade (Grade I) or graded wood particle board IS : 3087 marked, to frame, backing or studding with screws etc. complete (Frames, backing or studding to be paid separately): (a) 12 mm thick

Providingand Fixing GI Fastener 100x8 mm for properly fixing overhead cabinets to the wallls

Providing & fixing glass panes: (a) Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm)

Supplying and fixing new wooden fillets wherever necessary: (a) Hollock wood fillets

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :

(a) 12.5 mm thick tapered edge gypsum moisture resistant board

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. Complete

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand)

6 mm cement plaster of mix :1:3 (1 cement : 3 fine sand)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : (a) Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Providing & fixing Signages (stainless steel) 3 mm thick S.S. Plate with engraving of letters completed as per direction of Engineer-In-Charge

Supply of following worker along with necessary tools & equipments for related work from 9.00AM to 5.00 PM

(a) Masson

(b) Carpenter

(c) Labour

Buy Back old dismantled Aluminium Sections taking out of NIScPR building premises including loading unloading and transportation etc. complete. The weight of the material will be ascertained on the basis of loading vehicle and the tare weight of the vehicle after weighting the same at weigh bridge (Dharam kaanta). The charges will be borne by the contractor.

Buy Back old dismantled M.S. Sections taking out of NIScPR building premises including loading unloading and transportation etc. complete. The weight of the material will be ascertained on the basis of loading vehicle and the tare weight of the vehicle after weighting the same at weigh bridge (Dharam kaanta). The charges will be borne by the contractor.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. Make:- Polycab/Havells/RR Kabel

2 X 2.5 sq. mm + 1 X 2.5 sq mm earth wire

2 X 4 sq mm + 1 X 4 sq mm earth wire

2 X 6 sq. mm + 1 X 6 sq. mm earth wire

Supplying & drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. Make:-Legrand

1 run of cable

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.Make:-Delton/Polycab/Havells

Testing and Punching of Cat-6 cable in the existing RJ-45 wall sockets and network switches.

Testing and Punching of telephone wire cable in the existing RJ-11 wall sockets and MDF box.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.Make:-Legrand Myrius/Havells Crabtree/ABB

5/6 amp switch

3pin 5/6 socket outlet

Telephone socket outlet

Supplying and fixing following size/ modules GI box alongwith modular base and cover plate for modular switches in recess etc. as required. Make:-Legrand Myrius/Havells Crabtree/ABB

6 module (200 mmX 75 mm)

8 module (125 mmX 125 mm)

12 module (200 mmX150 mm)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required. Make:-Legrand Myrius/Havells Crabtree/ ABB

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. Make:-Legrand Myrius/Havells Crabtree/ABB

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required.

Supplying,installation,testing and commissioning of RJ 11 double telephone socket with shutter legrand make alongwith metal flush /PVC boxes legrand make and modular white plates legrand make on surface/ recess/ table trunking trench as required. Make:- Legrand Myrius

Supplying,installation ,testing and commissioning of modular type legrand make internet point RJ 45 (Information outlet) with shutter with modular metal/PVC box and plate in floor/ DLP/ Work Station or wall including cutting/ chasing etc complete as required. Make:- Legrand Myrius

Supplying and fixing DP sheet steel enclosure on surface/ recess along with 25/32amps 240 volts "C" curve DP MCB complete with connections, testing and commissioning etc. as required.Make:- Legrand

Supply & fixing of suitable size unbreakable box deep on surface or in recess or in DLP with suitable size modular plate cover in the front including providing and fixing 3 Nos 6 Amps modular type socket outlet with 1 no. 16 Amps modular type switch and suitable blanking plate connections, painting etc. complete as required. Make:- Legrand Myrius/Havells Crabtree/ABB

Supply & fixing of suitable size unbreakable box deep on surface or in recess or in DLP with suitable size modular plate cover in the front including providing and fixing 2 Nos 6/16 Amps modular type socket outlet with 2 nos 16 Amps modular type switch, connections, painting etc. complete as required. Make:- Legrand Myrius/Havells Crabtree/ABB

Supply andf ixing of following sizes of PVC conduit along with accessories in surface/recess/table trench including cutting the wall and making good the same incase of recessed conduit as required. Make:- Setia/AKG

Supply and fixing of PVC channel 20mm (W)X12 mm (D) along with accessories in surface/recess/chisseling of ceiling/ cutting the wall and making good the same incase of recessed channel as required. Make:- Setia/AKG

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Make:- Legrand

Single Pole

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A, tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer) as required. Make:- Legrand

8 way (4 + 24), Double door

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.Make:- Legrand

125 A, 36kA, FPMCCB

Supply & fixing of one number metal one way enclosures of DPX3 250 MCCB enclosure having no. of modules 3P & 4P on surface with drilling holes and making connections etc alongwith providing and fixing of 160 A, 36kA breaking capacity, DPX 160 FP MCCB with thermomagnetic release and terminal spreaders in enclosure including drilling holes in enclosures, making connections, etc. as required. Make:- Legrand

Supplying and fixing Cable End Box (Loose Wire Box) suitable for triple pole and neutral, sheet steel, Vertical MCB distribution board, 415 Volts, on surface/ recess, complete with testing and commissioning etc. as required. Make:- Legrand

SSupplying and fixing following rating miniature circuit breaker 'c' series in the existing MCB DB complete with connections, testing and commissioning etc as required. Make:Legrand

MCB 40 Amp SP 240 V

Supplying, installation, testing & commissioning of aesthetically designed LED flat panel for surface / suspended mounting 36 W fixture size(LxWXH) in (600x600x70) mm which provides soft light and glare free symmetrical illumination with complete electronic driver as required including all needed materials for completing the work.Make: Havells/ Philips

Supply, Installation, Testing and Commissioning of wall mounted fan having 400 mm sweep, 1350 RPM, 65m3/min, 50 W, 50 Hz frequency including all materials needed for completing the work. Make:-Havells/Orient/Atomberg

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. Make:-Legrand

Dismatling of existing light fittings, wires,armoured cables, switch plates, distribution boards, MCBs, MCCBs, earthing wires, metal boxes, ceiling fan, exhaust fan, window/ split airconditioning etc complete as required and deposite the same to the engineer incharge.

Supplying of one number ISI marked following sizes aluminium conductor XLPE insulated armoured power cable of 1.1 KV grade as required. Make: Polycab/Havells/ RR Kabel

4 core X 50 sqmm

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed/ XLPE aliminium conductor cable of 1.1 KV grade as required.Make: Dowells

4 X 50 sq. mm (35 mm)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size on wall surface as required.

Above 35 sq. mm and upto 95 sq. mm (clamped with 25X3mm MS flat clamp)

P/F 10 SWG Dia wire on surface or in recess for loop earthing as reqd.

Supply ,installation, testing and commissioning of cordless remote control window type energy efficient air conditioners of cooling capacity of 24,000 BTU/Hr. (2.0TR) consisting of hermetic sealed rotary type compresser,air cooled copper condenser, fan motor, DX cooling coil,filters, controls like timers,auto restart , temperature control sensor,Air swing etc., cabling, wiring and first charge of referigerant and oil etc., suitable for single phase ,230 V, 50Hz, power supply with minimum 2-star rating or above with a warrantee of one year of complete AC unit & 5 years of compressor. Make- Blue Star/ Hitachi/ Carrier .

Supply ,installation, testing and commissioning of inverter type split air conditioner unit of 24000BTU/Hr (2.0 TR) cooling capacity each comprising an outdoor unit consisting of hermetic compresser rotary type, air cooled copper condenser, condenser fan, expansion device ,etc .and indoor unit consisting of centrifugal fan ,fan motor , DX cooling coil, outer casing ,filters ,control etc. both interconnected with copper refrigerent pipe (up-to 3m included in cost),cabling ,wiring, insulation and first charge of refrigerent and oil etc , suitable for single phase ,230V,50HZ., power supply, Make- Carrier/ Hitachi/ Mitsubushi & Minimum 5- star rating. All masonary work such as supports for any equipment , opening of hole in the wall etc. included and making the good.

Supply and fixing of MS steel stand suitable for 2.0 TR outdoor units duly painted to be installed at roof top /floor.

Supply and fixing of suitable size copper refrigerent pipe with proper insulation along with control cum transmission cable of 4core X 2.5 sqmm copper conductor PVC insulated cable for interconection of outdoor units and indoor units along with. All piping and wire inside the rooms is under the chizzled wall and outside the room shall be properly clamped along the wall.

Supply and fixing of 25/32mm dia CPVC/ PVC AC water drain pipe with bends, reducers, tees, support stand etc. as required to complete the work.

Supply and making chizzling work for fixing of copper referigerent pipe and drain pipe complete as required..

Supply ,installation, testing and commissioning of single phase auto cut voltage stabiliser, copper winding with time delay relay etc. complete in all respect with a warrantee of minimum one year as following details:-Capacity-5KVA, input-170V to 250V,50Hz, output-220V to 240V, 50Hz

Dismantling of GI AC ducts and supporting Iron members etc. buy back the dismantled existing GI AC ducts and supporting iron members and old reinforced bars from brick walls etc. taking out of NISCAIR building premises including loading unloading and transportation etc. complete. The weight of the material will be ascertained on the basis of loaded vehicle and the tare weight of the vehicle after weighing the same at weigh bridge.

PREM NATH CONSTRUCTION CO

S P CONSTRUCTION