ADDN / ALTN TO NEW HANGAR AT AIR FORCE STATION UDHAMPUR

Amount

Excavating in post holes (or similar holes) each n exc 0.5 cum getting out ,returning filling in and ramming earth or broken rubble mixed with earth around ,in layers not exceeding 25 cm, watering,and removing surplus soil to a distance n exc 50 m and making good surface complete all as specified and directed by Engr-in-Charge.

M&L for framed work such as grills,gratings etc.with ends of bars shouldered and/or riveted,or riveted,or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work con-forming to Fe-290.Gde-E-165 complete all as specified and directed by Engr-in-Charge.

M&L for Mild steel work as in Stairs (Framed) incl stringers, treades, landing, balusters, hand rail etc, including cleats, brakcets etc complete all as specified and directed by Engr-in-Charge.

M&L for PCC 1:2:4 type B-2 using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed by Engr-in-Charge.

S&F Linoleum sheet 3.2/3.3 mm thick, plain coloured, laid dry in floors including stretching, cutting and fitting incl sealed down with an approved adhesive complete all as specified and directed by Engr-in-Charge.

M&L for Preparation of new or previously untreated steel surfaces of any description over 10cm width or girth, applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed by Engr-in-Charge.

S&F powder coated aluminium doors shutters, (thickness of powder coating not less than 50 micron) aluminium section weighing exc 0.55 Kg/m including necessary joining cleats, glazing clips rubber neoprene packing, handle 2 Nos in each door, fixed with floor hinges anodised aluminium snap beading screws etc complete all as specified and directed by Engr-in-Charge.

S&F Power coating Aluminium (Minimum thickness of power coating 50 micron) for doors, window, ventilators and partitions (Fixed postions) with extruded built up standard tubular section /appropriate Z section and other section of approved make conforming to IS : 733 and IS : 1285, fixing with dash fasteners of required dia and size incl necessary filling up the gaps at junctions, i.e at top, bottom and sides with required EPDM rubber/neoprene gasket etc aluminium sections shall be smooth , rust free, straight mitred and jointed mechanically wherever required incl cleat angle aluminium snap beading for glazing/paneling, CP brass/stainless steel screw, complete all as specified and directed by Engr-in-Charge.

S&F aluminum powder coated of any colour (thickness of powder coating not less than 50 micron), in frame for doors, window, ventilators, partition wall etc, with one or more rabates, shutters, grills inlcuding joining cleat for fixing etc complete all as specified and directed by Engr-in-Charge.

S&F 5.5mm thick ordinary quality glass fixed to doors , window and partion but exc .5 sqm in a each pane complete all as specified and directed by Engr-in-Charge.

S&F rubber beading of required size for fixing of glass/ACP sheets etc as in aluminium doors/windows/partitions complete all as specified and directed by Engr-in-Charge.

M&L for Providing, cement concrete type B1 1:2:4 20mm graded stone aggregate in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed by Engr-in-Charge.

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed by Engr-in-Charge.

S&F Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) of Fe 410 -W (Gde- E- 250) quality- A for ceiling frame complete all as specified and directed by Engr-in-Charge.

M&L for 6 mm thick Non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework with screws fixed in ceiling flat or sloping complete all as specified and directed by Engr-in-Charge.

M&L for Reinforced Cement Concrete Nominal mix type B-1 1:2:4 ( using 20 mm graded crushed stone aggregate) as slabs supported on walls, beams and columns, in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed by Engr-in-Charge.

M&L for Form work to soffits of RCC suspended slab such as roof slab, floor slab, landing and similar work not exceeding 200mm thick surface horizontal or sloping, rough finished surface of concrete, complete all as specified and directed by Engr-in-Charge.

M & L for TMT bars (Fe-500) 10mm dia and over in reinforcement cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, placed in position, complete all as specified and directed by Engr-in-Charge.

M & L for brick work with sub class 'B' brick straight of curved on plan exc 6m mean radius built in CM 1:4 complete all as specified and directed by Engr-in-Charge.

Rendering 15mm thick in Cement Mortar 1:4 on fair faces of Brick Walls or on Concrete Surfaces, finished fair and even without using extra cement complete all as specified and directed by Engr-in-Charge.

M&L for applying three coats of white wash on walls incl preparation of newly plastered or unplastered surfaces complete all as specified and directed by Engr-in-Charge.

S&F 20mm stove enamelled steel conduit including junction boxes,elbows,sockets ,tees and Nipple etc to connect from any point of wall / ceiling to laying / fixed to false ceiling / wall complete all as specified and directed by Engr-in-Charge.

Supply, laying, commissioning & testing of cable for fire detection and alarm system of size 1.5 sqmm 2 core copper conductor PVC Insulated flexible FRLS, wires drawn in existing conduit as required complete all as specified and directed by Engr-in-Charge.

Taking down, reinstallation, commissioning, programming and testing of fire Alarm Panel of Honeywell, Model No DX2, two loops complete all as specified and directed by Engr-in-Charge.

M&L for taking out of existing smoke detector with connecting wire & refixing the same at location specified or deposite to AGE E/M store as required complete.

Cutting openings, through puff panels for door, window and other openings or enlarging existing opening etc or cutting out defective portion including cleaning complete all as specified and as directed by Engr-in-Charge

DAVINDER SINGH (BID ID -3085061)

SHIVAE CONSTRUCTION (BID ID -3080318)

ASIA BUILDER (BID ID -3087488)