PROVISION OF PARKING SHED FOR AD INTEGRATION SEPARATE CELL IN DCMM AC POINT FOR PROJECT EOSAAW EARTHING WITH ALLIED WORKS AND PERMANENT WATER SUPPLY FOR EMI EMC PRODUCTION CENTRE AT RCI HYDERABAD

Amount

M&L for Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan in all kinds of soil including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m complete all as specified and directed.

M&L for Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) in all kinds of soil including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m complete all as specified and directed.

M&L for Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), in all kinds of soil including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m complete all as specified and directed.

M&L for Excavating holes more than 0.10 cum & upto 0.5 cum in all kinds of soil including getting out the excavated soil, then returning the soil as required in layers not exceeding 20cm in depth, including consolidating each deposited layer by ramming, watering etc, disposing of surplus excavated soil, as directed within a lead of 50 m and lift upto 1.5 m complete all as specified and directed.

M&L for Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in Cement mortar 1:4 (1 cement : 4 coarse sand) complete all as specified and directed.

M&L for 15 mm thick cement plaster on the rough side of single or half brick wall of mix : 1:4 (1 cement: 4 fine sand) complete all as specified and directed.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources as directed complete all as specified and directed.

Providing and fixing of Steel work in built up tubular sround, square or rectangular hollow tubes etc.) trusses (Hot finished welded type tube) etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc., complete all as specified and directed.

Providing and fixing of Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required complete all as specified and directed.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required complete all as specified and directed.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete Ridges plain (500 - 600mm) complete all as specified and directed.

Supplying and stacking at site 63 mm to 45 mm size stone aggregate complete all as specified and directed.

M&L for Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform thickness, hand picking, rolling with 3 wheeled road/vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of coarse aggregate, watering and compacting to the required density complete all as specified and directed.

M&L 100mm thick PCC 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) complete all as specified and directed.

M&L 100mm thick PCC 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) complete all as specified and directed.

M&L for Finishing Painting on Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture complete all as specified and directed.

M&L for Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives complete all as specified and directed. New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm.

Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead complete all as specified and directed.

Providing and fixing powder coated aluminium(minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws / dash fasteners etc., complete all as specified and directed. complete all as specified and directed. NOTE: Panelling and glazing will be measured and paid separately under relevant items of this BOQ.

Providing and fixing powder coated aluminium(minimum thickness of powder coating 50 micron) work for shutters of doors, windows, ventilators with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws / dash fasteners etc., complete all as specified and directed. NOTE: Panelling and glazing will be measured and paid separately under relevant items of this BOQ.

Providing and fixing 12 mm thick Pre-laminated particle board with decorative lamination on both sides flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc., complete all as specified and directed.

Providing and fixing glazing with float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc., complete all as specified and directed. NOTE: Cost of aluminium snap beading is included in above items.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc., complete all as specified and directed.

Providing and fixing aluminium tower bolts 150x10 mm , ISI marked, anodised (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour or shade, with necessary screws etc., complete all as specified and directed.

Providing and fixing IS : 12817 marked stainless steel butt hinges 100X58X1.90 mm with stainless steel screws etc. complete all as specified and directed.

Providing and fixing aluminium handles 125 mm , ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc.complete all as specified and directed.

Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc.complete all as specified and directed.

Providing and fixing false ceiling With 15 mm thick integral densified micro edge light weight calcium silicate false ceiling tiles at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity < 0.043 W/m K as per ASTM 518:1991, in true horizontal level suspended on interlocking metal powder coated T-Grid of hot dipped galvanised iron section of 0.40 mm thick on Silhouette profile,rotary stiched double webbed white with 6mm reveal profile (white/black),comprising of main-T runners of size 15x42mm of length 3000 mm, cross - T of size 15x42 mm of length 1200 mm and secondary intermediate crossT of size 15x42 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 22x19x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall S.S screws complete all as specified and directed.

Steel work in built up tubular hot finished seamless type tubes (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc., complete all as specified and directed.

Providing & fixing UV stabilised fiberglass reinforced plastic sheet 2mm thick flat roofing up to any pitch, including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth complete all as specified and directed.

Providing and laying Vitrified tiles in floor Size of tile 600x600mm (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily complete all as specified and directed.

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 Sqmm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required complete all as specified and directed.

Wiring for circuit/ submain wiring alongwith earth wire with 2 x 2.5 Sqmm + 1 x 2.5 Sqmm earth wire of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required complete all as specified and directed.

Wiring for circuit/ submain wiring alongwith earth wire with 2 x 4 Sqmm + 1 x 4 Sqmm earth wire of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required complete all as specified and directed.

Wiring for circuit/ submain wiring alongwith earth wire with 4 x 6 Sqmm + 2 x 6 Sqmm earth wire of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required complete all as specified and directed.

S&F modular switch 16A on the existing modular plate & switchbox including connections but excluding modular plate etc., as required complete all as specified and directed. MAKE: ANCHOR ROMA/ CRAB TREE/ L&T / HAVELLS

S&F modular socket 2 module 3/5 pin 16A on the existing modular plate & switch box including connections but excluding modular plate etc. as required complete all as specified and directed. MAKE: ANCHOR ROMA/ CRAB TREE/ L&T / HAVELLS

S&F 3 Module (100mm x 75mm) modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required complete all as specified and directed. MAKE: ANCHOR ROMA/ CRAB TREE/ L&T / HAVELLS

S&F 2 x 2 LED recess mounting 36 Watt luminaire suitable to operate on 230 volts single phase AC supply complete all as specified and as directed. MAKE: HAVELLS/ WIPRO/ PHILIPS

S&F Cable End Box (Loose Wire Box)For 8 way, Double door SPN MCB DB suitable for following single pole and neutral, sheet steel, MCB distribution board, 240 Volts, on surface/ recess, complete with testing and commissioning etc., as required complete all as specified and directed. MAKE: L&T/ LEGRAND/ INDO ASIAN/ C&S

S&F MCB SPN, 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load in the existing MCB DB complete with connections, testing and commissioning etc., as required complete all as specified and directed. MAKE: L&T/ LEGRAND/ INDO ASIAN/ C&S

S&F MCB SP, 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load in the existing MCB DB complete with connections, testing and commissioning etc., as required complete all as specified and directed. MAKE: L&T/ LEGRAND/ INDO ASIAN/ C&S

S&F ceiling fans complete with blades, down rods, electronic regulator and accessories , 230V, 1200mm sweep, minimum air delivery 210 CFM with service value 6.00, BEE five star rated with brushless direct current motor (BLDC) complete all as specified and directed. MAKE: ATOMBERG/ HAVELLS/ ORIENT/ CROMPTON GREAVES

Wiring for circuit/ submain wiring alongwith earth wire with 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required complete all as specified and directed.

Wiring for circuit/ submain wiring alongwith earth wire with 2 X 4 sq. mm + 1 X 4 sq. mm earth wire of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required complete all as specified and directed.

Wiring for circuit/ submain wiring alongwith earth wire with 4 X 6 sq. mm + 2 X 6 sq. mm earth wire of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required complete all as specified and directed.

Wiring for circuit/ submain wiring alongwith earth wire with 4 X 10 sq. mm + 2 X 6 sq. mm earth wire of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required complete all as specified and directed.

Wiring for circuit/ submain wiring alongwith earth wire with 4 X 16 sq. mm + 2 X 6sq. mm earth wire of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required complete all as specified and directed.

S&F, sheet metal enclosure for pre wired distribution board double door, powder coated VTPN, 4 way with out MCCB, three phase 415 volt with 250 Amps rated tinned electrolytic copper bus bar with neutral link complete all as specified and directed.

S&F, MCCB, 4 Pole 250Amps capacity 25KA 415Volts 50 HZ complete all as specified and directed .

S&F, MCB three pole (TP) 10 kA of 40 Amps capacity 430 Volts 50 HZ complete all as specified and directed .

S&F, MCB three pole (TP) 10 kA of 100 Amps capacity 430 Volts 50 HZ complete all as specified and directed .

S&F in repairs, CRCA sheet metal enclosure with metal clad plug and socket three phase with a five pin and earth plug & socket suitable for surface/flush mounting, 415V, 32 Amp capacity controlled by and including one No 32Amp MCB TPN 10KA complete all as specified and directed.

S&F in repairs, CRCA sheet metal enclosure with metal clad plug and socket three phase with a five pin and earth plug & socket suitable for surface/flush mounting, 415V, 100Amp capacity controlled by and including one No 100 Amp MCB TPN 10KA complete all as specified and directed.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required complete all as specified and directed.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long with charcoal/ coke and salt as required complete all as specified and directed.

Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required complete all as specified and directed.

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm complete all as specified and directed.

Supplying and fixing following modular switch 16A on the existing modular plate & switchbox including connections but excluding modular plate etc. as required complete all as specified and directed.

Supplying and fixing following modular socket 2 module 3/5 pin 16A on the existing modular plate & switch box including connections but excluding modular plate etc. as required complete all as specified and directed.

Supplying and fixing Cable End Box (Loose Wire Box)For 8 way, Double door SPN MCBDB suitable for following single pole and neutral, sheet steel, MCB distribution board, 240 Volts, on surface/ recess, complete with testing and commissioning etc. as required.

Supplying and fixing MCB SPN,5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required complete all as specified and directed.

Supplying and fixing MCB SP, 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required complete all as specified and directed.

S&F in repairs CRCA sheet metal enclosure with metal clad plug and socket single phase with three pin and earth plugh & socket sitable for surface/flush mounting 230 V, 20 Apms capacity controlled by and including one 20 Amps MCB , 10 KA capacity complete all as specified and as directed.

Supply and fix testing of Earthpuls Advanced earthing system A) Earth plus advance Earthing Electrode:- Copper Banded Rod (Testes As per IEC 62561-2 by NABL Accredited Lab & CPRI) "UL listed " High tension low carbon soild steel electrode, 300 mm lenth, 17.2 mm dia with copper nonded thickness 254 microns, complaint to revent IEEE 80-1986, IEEE 665-1995, IEC 62561-2, Standed & Tested For: a) Short Time Current test CPRI25 KA, b) BeindingTest, c) Adhesion Test, d) Dimenaion Measurement Test, e) Envirnomental Test, f) corrosion Test, g) Tensile Strength and Clogation Test, h) Test for material commposition, i) Test for verfication of coating thickness, j) Electrical Resistance measurment test model : SMI-CB-1703UL

B) earthplus "ULTRA" High -Grade earthing Compound (Tested as per IEC62561-7 & IEE 80 by NABLA. Accredited Lab) : Ecoofriendly maintenance free comsive, lead free conductive, mineral based high grade earthing compound , Tehhance soil conductivly. Ahving resistance of 0.095 ohms-meter, in completely I each proof & silphur free tasted per IEC-62561-7, ASTM G 57-06, ASTM G-59-97, AST G 102-89. ISO 4689-3 EN 12457-2 Packed in Eco Friendly HDPE: Laminatedd pare bage 25 Kg x 2 Bags(i.e 50 Kg) C) Connection Clamp: GUV Body with M10 X 50 mm stainless XL 304 nuts, Bolts & washers 'H-type' Connection clamp D) Concrete Inspection Pit: Heavy duty, Precast correct inspection chamber with cover size 320 mm (W) x 320 mm (L) X 192 mm (H), clear opening 180 mm Weight 30 Kgs. Load bearing capacity : 5000Kgs. E) Installtion : Installation of Each Earth Pit F) Copper Flat : 25 x 3mm

Supply and fixing copper strip 25 x 3mm (1.15Kgs per meter)

Cutting GI pipe of any size and reducing to required length before laying and insertion of 'T's of 50X50X25mm and branches for 25 mm all as specified and as directed.

Supply and lay GI pipe medium garde of size 25 mm dia including all bends, tees, fittings etc all as specified and directed.

Supply and fix 25 mm gate valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed

S&F in repairs, 500 litres capacity triple layered rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position including connecting up of existing inlet and outlet pipes and ball valve complete all as specified and as directed.

Supply and fix 25mm size ball brass valves,high pressure, with polythene float and flynut complete screwed for iron pipe or brass ferrule and fixed complete.

Excavation in trenches not exceeding 1.50m wide and not exceeding 1.50m depth for foundation, for laying of pipes/cables/poles etc., forming bottom surfaces to required slope/gradient where pipe are laid and getting out in any type of soil complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick each layer as in soil complete all as specified and as directed.

Removing excavated material/soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed.

Maruthi international

M/S GDR CONSTRUCTIONS

SHAH ENTERPRISES