SPECIAL REPAIR TO TOILET AND BATHROOMS AT KV SCHOOL NAGROTA UNDER GE NAGROTA.

Amount

Taking down chowkat with shutter (without taking off shutter from the frame) not exceeding 1.5 sqm, complete all as specified and as directed at site.

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground levels), complete all as specified and directed.

Demolition of brick work / stone masonry built in cement mortar or cement lime mortar including all quoins ,arches , pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles, complete all as specified and directed.

Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specifically provided for complete all as specified.

Taking down cement plaster on brick or stone walls etc including raking out joints hacking for key scrubbing down with water etc, complete all as specified and directed.

Taking up or down steel water tubing and connection of 15 mm bore, complete all as specified and directed.

Taking up or down steel water tubing and connection of 20 mm bore, complete all as specified and directed.

S&F 15 mm bore steel water tubing medium grade galvanised with all fittings such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc laid in wall and floor etc complete all as specified and directed.

All as per item No.8 here-in-before but 20 mm bore.

S & F factory made solid PVC moulded door shutter 28 to 30 mm thick (stiles) with 2, 4 or 6 raised panel design with 2 mm thick moulded PVC sheet on front face and 2 mm plain colour PVC sheet on back face, complete all as specified and directed.

Box type steel window side hung double shutters with provision for desert coller/AC (Inside for wire mesh & outside for glass), including guard bar hinges, steel handle, tower bolt and steel peg stay complete with glazaing bar dovetailed for welded and fixed steel window shall be conforming to relevant IS complete all as shown on drawing No CEUZ/TD/1302/09, Sh 1/3 to 3/3 including taking down of existing steel windows, complete all as specified and directed. Note : Wire mesh and sheet glass shall be measured and paid separately.

Box type Steel ventilators top hung double shutters (inside for wire mesh & out side for glass), including hinges, steel handle, tower bolt and steel peg stay complete with glazing bar dovetailed or welded including a coat of red oxide after preparation of surface before fixing.Steel window shall be conforming to relevant IS, complete all as specified and directed. Note : Wire mesh and sheet glass shall be measured and paid separteley.

Pressed steel door frame of size 105 mm x 60 mm with one or more rebates using 1.25 mm thick sheet including necessary fixing lugs, lock strike plate including one shop coat of zinc chromate primer, complete all as specified and directed.

Prepration of new or previously steel surfaces any description, not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

S&F of framed work as in door (as in chowkats) or gates of angle or other section with guest plates rails, braces rail etc exclusive of steel sheeting or other covering hanging also fastening and fixing comforming to Fe-410-0 or Fe-310-0 including shop coat of red oxide including preparation of surface before fixing, complete all as specified and directed.

S & F 150mm aluminium anodised barrel tower bolt of extruded section and fixed, complete all as specified and directed.

S & F 150 mm aluminium handles cast type anodized, complete all as specified and directed.

S & F 100 mm aluminium handles cast type anodized, complete all as specified and directed.

S & F 100 mm long butt hinges, medium weight, cold rolled mild steel, complete all as specified and directed.

S & F 3.00 mm thick Sheet glass ordinary quality and glazing with oil putty and pin(steel spring for fixing glass) in square n exc 0.5 Sqm in each pane including hacking out old glass panes, complete all as specified and directed.

S & F Galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm dia and fixed with tinned tacks or galvanised mild steel staples, complete all as specified and directed.

S & F MS Sliding door bolts clamps type stove enameled black with bright bolt not less than 12 mm dia with and incuding a minimum of 06 bolts and nuts 04 bolts, clamps and 02 staples of bolts 200 mm long, complete all as specified and directed.

M&L for 50 mm thick PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in plinth protection, complete all as specified and as directed.

M&L brick work with sub class 'B' bricks in 1:4 cement mortar on straight or curved on plan n. exc 6 m , complete all as specified and directed.

Supply only integral water proofing compound, all as specified .

S & F GI 50 mm bore pipe medium grade with all fittings and fixed, complete to walls as in spout pipe including making holes for pipe, complete all as specified and directed.

S & F 100 mm dia bore Cast iron waste and vent pipes sand cast in any length with or without ears with cement joints laid in floors or fixed to walls with all fittings includign taking down the unservicable pipe with fitting, complete all as specified and directed.

All as per item No.27 here-in-before but 75 mm bore dia.

Extra over cast iron pipes and fittings if lead joint is provided in lieu of cement joint of 100 mm bore, complete all as specified and directed.

Extra over cast iron pipes and fittings if lead joint is provided in lieu of cement joint of 75 mm bore, complete all as specified and directed.

S & F 100 mm bore CI bends any radius, complete all as specified and directed.

S & F 75 mm bore CI bends any radius, complete all as specified and directed.

S & F branch pipe single of 100 mm bore or with parralel branches, complete all as specified and directed.

S & F branch pipe double of 100 mm bore or with parallel branches, complete all as specified and directed.

S & F CI branch pipe single of 75 mm bore or with parallel branches, complete all as specified and directed.

S & F CI pipe double of 75 mm bore or with parallel branchs, complete all as specified and directed.

M & L for 50 thick PCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in sub base of floors including finishes the surfaces even and fair, complete all as specified and directed.

Vitreous china urinal, half stall type, flat back, size 635 x 395 x 420 mm, coloured, with grating and union for discharge pipe , waste coupling and waste pipe, comolete all as specified.

S&F in repairs vitrous china wash basin,white, counter type,size 450 mm oval type with and including CP pillar tap and waste coupling, angle brackets, PVC connection 15 mm bore 600 mm long, PVC waste pipe, complete all as specified and directed.

M & L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM 1:6 finished even and smooth without using extra cement, complete all as specified and directed.

M&L for 15 mm thick rendering on fair faces of brick work in cement mortar 1:4 and finished even and smooth without using extra cement complete all as specified.

M&L for 10 mm thick rendering in CM 1:3 on ceiling fair faces of brick/concrete surfaces rough finished even and smooth without using extra cement complete all as specified.

M & L for Glazed ceramic coloured printed tiles (first quality) of size 600mm x 300 mm x 7-8 mm thick as in vertical surface, dado/skirting, over and including 10 mm thick screed bed in CM 1:4, complete all as specified and directed.

M & L for non skid ceramic coloured tile 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc set and jointed (joint free) in neat cement slurry and pointed in coloured cement to match the shade of the tiles over 15 mm thick screed in CM 1:4, complete all as specified and directed.

M & L for preparation of new plastered or unplastered surfaces of walls and applying two coats of white wash, complete all as specified and directed.

All as per item No.46 here-in-before but on ceiling.

All as per item No.46 here-in-before but two coats cement base paint over a coat of white wash.

S&F in repair 15 mm bore stop/angle valve fancy type , cromimum plated with long shank(concealed type) cast copper alloy screwed down high pressure a handle screwed both ends for iron pipe or union, complete all as specified and directed.

S&F 10 ltr capacity PVC low level flushing cistern syphonic action type white with inlet valve float and handle including brackets, fixed in repair complete all as specified and directed.

S&F in repair Viterous china squatting any type pan Orrisa pattern long pan size 580mm x 440mm white with P or S trap, front and Integral foot rests any pattern excluding flushing cistern and flushing pipe, complete all as specified and directed.

S & F vitreous china wash down water closet pan semi-pedestal pattern (Anglo-Indian type), white (excluding supply of flushing cistern and flush pipes, but including fixing thereof), including seat cover & making connections to trap, and to flush pipe and fixed in repair, aspd

S& F PTMT grating 100 mm size, complete all as specified and directed.

S & F 15mm bore pvc connection 600 mm long, complete all as specified and directed.

M&L 75 mm cast iron floor trap in cement concrete 1:2:4 type B-1 with grating including jointing to waste pipe fixed complete all as specified and directed

S & F CP brass bib tap 15 mm cast copper alloy with screwed down screwed for iron pipe, complete all as specified and directed.

S & F CP angle valve/consealed stop cock of cast coppper alloy (ISI Marked) chromium plated fancy type screwed down high pressure with capstain head screwed both ends for ironn pipe 15 mm bore, complete all as specified and directed.

S & F CP brass bib tap long nose 15 mm fency type with captain head screwed down screwed for iron pipe of 15 mm, complete all as specified and directed.

S & F in repairs 75mm bore dia cast iron cowls fixed, complete all as specified and directed.

Taking down existing cement plaster of any description (sunken floor) apply a coat of cement slurry with 3.00 kg of cement per sqm and rendering 15 mm thick I CM 1:3 using WPC finished even and smooth including filling with brick bats to (sunken floor/wall) Note:WPC to be measured and paid spearately.

M & L for PCC 1:2:4 type B-1 (using 20 mm graded aggregate) as in blocks for hold fasts, benchig coping apex stones, bend plates and the like including weathering slighly rounded or chamfered angles and throating all as specified and directed. Note : Form work required for these items included in the unit rate of this item.

M & L for 18 to 20 mm thick granite black (table rubbed and polished) in stpes, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, over 15 mm thick screed bed in CM 1:4,complete all as specified and directed.

M & L for rounding to edges of stone slabs one edge such as in steps, cooking platform and other similar situation, complete all as specified and directed.

M & L for reinforced cement concrete 1:2:4 (nominal mix) as in slabs supported on walls, beams and columns and the like slab laid in stops, complete all as specified and directed.

S&F mild Steel TMT bars 10 mm dia and over in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified.

Form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exceeding 200 mm thick (horizontal or sloping), complete all as specified and directed.

M & L brick work with subclass 'B' bricks straight or curved on plan to any radium in half brick thick walls built in CM 1:4, complete all as specified and directed.

Taking down carefully aluminium conductor point wiring (light fan, socket and power) complete with fittings such as switches, sockets, lamps holder, utility light fitting, fan regulator etc and making good disturbed surface of walls and floors etc. and keeping in safe custody for taking credit, complete all as specified and directed by Engr-in-Charge.

M&L for point wiring with PVC insulated unsheathed 1100 volt grade FRLS cable with multi stranded copper conductor of size 1.5 Sqmm (Nominal area) drawn through and including non metallic rigid PVC conduit medium grade ISI marked not less than 20mm dia ,concealed in wall and surface on ceiling with all conduit fittings & fixing acessories inculding sunken anodised pressed steel terminal box not less than 1.2 mm thick covered with 3 mm thick plastic laminated sheet cover of suitable size with brass screws for mounting switches, sockets, regulators with and including 1.5 sqmm FRLS multi stranded copper conductor drawing as continuous earth wire connected to main earth and earth dolly complete all as specified for the following;-

One light point controlled by one switch 5 Amp.

One ceiling fan/exhaust fan point controlled by one switch 5Amp

S&F switch piano flush type 5 Amps, single pole, one way, complete all as specified and directed.

S & F of ceiling rose 3 terminal complete PVC/Polycarbonate isolated boly, complete all as specified and directed.

S & F Integrel sleek extruded batten aluminium /CRCA channel fitting with LED 18 watt complete with all accessories and including connecting up with three core twisted flexible copper conductor cable with suitable size of 230V, 50 Hz, complete all as specified and directed.

S&F LED light fitting 1x9W bulk head luminaries IP 65 complete with all accessories including LED lamp 9 watt , connecting up with twin core twisted flexible copper conductor cable with suitable size of 230V 50 Hz, complete all as specified and directed.

S & F batten integrated LED channel of 5W, 230 V frequency 50/60 Hz integral sleek extruded polycarbonate LED channel with white acrylic cover, power factor not less than 0.9 , complete all as specified and directed.

S&F in repair sheet metal enclosure distribution board SPN 12 way 230 V, 50 Hz double door with neutral, Earthing bar and din rail, complete all as specified and directed.

S & F MCB DP 63 Amps 10 KA 230 volts "C" series, complete all as specified and directed.

S & F MCB single pole 6 to 30 Amps, 10KA, 230 volts 'C' series complete all as specified and directed.

Supply and fixing Exhaust fan 300 mm sweep single phase AC 230/240V complete with louvers for wall mounting including grouting, holding down bolts, nuts, washers and provision of flexible copper conductor cable 3 core 23/0.0076 size from ceiling rose to exhaust fan including cutting of the hole, complete all as specified and directed.

Deduction to be made from BOQ for schedule of credit (Sch 'A' Part - II) Amount of Rs.29,250.00 during AOC Note:- Tenderers shall not quote for this Schedule

M/S MANISHA BUILDERS

Kalsi Engineers and contractors

R.K. Works

Karmnaya Construction

ASHWANI KUMAR KHAJURIA AND SONS