Loading…
India Infra Updates on WhatsApp
Join the Tenderkart WhatsApp channel for India Tender Updates
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹1.1 LAccepted-Finance BYPASS NH NEAR SBI SIDHRA JAMMU | L1 | Accepted-Finance being lowest | |
| 2 | L2₹1.2 L+₹500 (0.44%)Rejected-Finance MAIN ROAD SIDHRA JAMMU | L2 | Rejected-Finance not lowest | |
| 3 | L3₹1.2 L+₹950 (0.83%)Rejected-Finance BHAGWATI NAGAR JAMMU | L3 | Rejected-Finance not lowest |
Tender Value
₹1.2 L
EMD Value
₹2,340
Closing Date
19 Jun 2023, 2:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Executive Engineer
MID JAMMU
Repair/replacement of worn out parts of 5 cusec x 10m head pumping unit no 1 along with allied works at LIS Dai Chak
2023_IFC_214114_1
MID/J/e-NIT/2023-24/26
Open Tender
Repair and Maintenance Works
Item Wise
10 days
Dai Chak
As per ENIT
8 documents required · 8 mandatory
₹200
EXECUTIVE ENGINEER MID JAMMU
₹2,340
Yes
5 Aug 2023
30 May 2023
20 Jun 2023
30 May 2023
19 Jun 2023
2 Jun 2023
Repair/replacement of worn out parts of 5 cusec x 10m head pumping unit no.1 along with allied works at LIS Dai Chak.
Decoupling of 05cusec x 10m head HC pump of unit no.1 at LIS Dai Chak from the motor assembly and dismantling the pump from the base frame. Also disengaging of the damaged & burnt 30HP electric motor of pumping unit no-1 of LIS Dai Chak from base frame and pump after disconnecting all electrical connections on input as well as output side. Carriage of the dismantled 05 cusec HC pump set, to the nearest roadside, using manual labour, head load through fields to nearest road side, loading in transport vehicle, carriage to the workshop in the mechanical transport for repairs. Repair to 5cusec horizontal casing pump set at workshop by way of dismantling and extraction of damaged internal parts. Repairs to the pump shaft by way of remetalling turning, rethreading & finishing to accurate size as per specifications of damaged pump shaft. Providing & fitting of new impeller in place of damaged one as per sample and fitting of the same on the pump shaft. Providing and fitting of 2no.s new bearings on driving and non driving end of the pump as per sample, 1no. neck ring, shaft protection sleeves, new gland studs and applying sufficient amount of grease to avoid excessive wear and tear, gland packing as per requirement. Complete assembling of pump set after carrying out necessary repairs. Shifting back to the LIS Dai Chak and then fitting/reinstallation at the base frame, coupling with the motor by making proper alignment and testing on partial/full load. Job also includes providing and fitting of new coupling nuts/bolts & rubber bushes. Dismantling of the damaged 30HP Motor at workshop for extraction of burnt/damaged windings, cleaning of stator slots and complete rewinding of the motor with new copper wires of requisite gauge and specifications of standard make. Providing/fitting of new insulation, packing material, then varnishing with superior quality varnish & drying in oven in controlled temperature. Complete job includes cost of material and labour charges. Repair to rotor of motor by providing/fitting of new bearings (DE & NDE) after rebuilding of the rotor shaft and finishing to bearing size, making new keyway for coupling, providing/fitting of bearing end cover plates and complete greasing of the bearings. Back carriage to site after repairs and reinstallation of motor commissioning and testing on idle and load conditions. Complete job includes cost of material including rebate on old copper scrap and labour charges with hiring charges of tools tackles and transport charges involved. Repair to the starter of unit-1 by way of dismantling of the starter at workshop and replacement of intermediate bakelite rod, moving and fixed contact points, no volt coil, thimbles, overload protection relay, back carriage to LIS for re-installation, commissioning and testing on no load and full load condition. Providing and filling of approx. 07 litres of fresh transformer oil to starter after de-moisturizing .Complete job including cost of material, labour charges and transport charges involved Providing/fitting of wire mesh around the intake sump tank of LIS Dai Chak 22ft approx. in length and 8ft height for protection of foot valves from the unnecessary polybags/garbage etc. flowing in the Canal. The job involves fitting the wire mesh around the sump area by way of fixing it on already grouted M.S angle iron (40x40x6 mm) pieces for holding of the mesh tightly either with help of nuts and bolts/wires. Job includes cost of material and labour charges for skilled and semiskilled labour, hire charges of tools and tackles to be employed at site for execution of job. Complete Job
Rebate on Old Parts
M/S TRIKUTA ELECTRICAL AND MECHNICAL WORKS
BEE AAR ENTERPRISES
BEE AAR ENTERPRISES
tech_eval.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .