Water Proof Treatment on the terrace of Type V VI staff quarters at NGRI Colony Hyderabad

Civil Works

Removing of betumin sheet/ coating and cleaning throughly, burning the surface of the bitumin removed with kerosene burner or butane torch with , cleaning including chipping / hammering/haking by gunhammer and removing of water tank platforms and chipping of cement surface and clean the surface with instant spoll absover for cementing works complete the job, disposal of material Out side NGRI campus as desired by the contractor

Demolishing brick work manually /by meachanical means including stacking of serviceable material and disposal of unserviceable material within disposal of material Out side NGRI campus as desired by the contractor

Chipping/ Roughing of Cement flooring and roofs/skirting/plaster etc laid in cement mortar, without damaging the existing RCC roof including stacking material and disposal of material inside along the Compound wall as per instructions by Engineer-In-Charge

Extra for providing and mixing water proofing material in cement plaster work including mixing of conplast X421C integral based water proofing compound or equivalent as per manufacturer specifications.

Providing and injecting approved grout in proportion recommended by the manufacturer of fosroc render roc plag /or equalient into cracks/honey-comb area of concrete/ masonry by suitable gun/pump at required pressure including, arranging required nozzigle points for pumping and cutting of nipples after curing etc. Stirrer mixed SBR Polymer (of approved make) modified Cement slurry made with Shrinkage Compensating Cement in concrete/RCC workcomplete as per directions of Engineer-in?Charge

Providing and applying two or more coats of Tapcrete with (1:2) ratio with gry cement and including laying of fibre mesh and applying of tapcrete sides of parapet wall up 300mm to complete the as per Instructions of Engineer-in-charage

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

Repairs to plaster of thickness 12mm to 40mm in patches of area 2.5 sq. metres or more area with 1:4 (1 cement : 4 coarse sand) and top layer 3 mm thick cement plaster 1:3 (1 cement : 3 fine sand) and mixing of water proof compound of With cement mortar 1:4 (1cement: 4 coarse sand) & 1:3 (1cement: 3 coarse sand) Conplast X421 IC including disposal of rubbish to the dumping ground within Out side the NGRI or at dumping place near at site as suggested by Engineer-In-Charge.

Grading roof for water proofing treatment with Providing and laying cement concrete 1:2:4 (1 Cement: 2 Coarse Aggregate : 4 graded stone aggreate of 12.50mm nominal size) of 40mm thick with 12.50mm nominal size stone aggregatefor terrace. Item includes mixing of water proofing compound Conplast X421 IC of M/s. Fosroc mixed @ 150ml per bag of cement which is been mixed for concrete. The work includes proper mixing of these items correctly, compacting and finishing the same to required slopes etc under including cutting the patch in proper shape raking out joints and cutting of groove preparing and plastering the surface of the walls and to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs in all leads and lifts complete all as required and directed by Engineer-In-Charge. (Once the concrete work is completed and the setting time is completed, the surface should be filled with water and kept for observation for 48 hours )

Providing and fixing of on wall face unplasticised - Reducer 150mm to 110mm dia PVC moulded fittings/ reducer 6" to 4" with accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

Brick work with common burnt clay Cement mortar 1:6 (1 cement : 6 coarse sand) F.P.S. (non modular) bricks of class designation 35 in superstructure above plinth level up to floor V level in all shapes and sizes in

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

Providing and fixing on wall face Plain bend 110mm dia unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

Providing and fixing on wall face Shoe 110mm dia unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

Providing and fixing 110mm dia GI clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, Code including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.

Removing and Refixing of Synthex PVC water tanks / asbestos sheet tanks including necessary fittings without any damaged and if any one damaged by contractor , it had been replace with new one with his own cost ,arrange the julas, screws etc to complet the job as per Instructions of Engineer-In-Charge

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, with make of ashirwad or equalient having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge

Providing and fixing ball valve 25mm (Cpvc) of approved quality, High or low pressure, with platic floats complete the work as per instructions of Engineer-in-Charge

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design to complete the job as per instructions of Engineer-In-Charge

Providing and laying APP (Atactic Polypropylene Polymer-make of LEAKSHIELD) modified prefabricated five layer 3 mm thick water proofing membrane, black finished reinforced with non-woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrane manufacture of density at 25°C, 0.87-0.89 kg/litre and viscocity 70-160 cps. Over the primer coat and one bitumen coat , the layer of membrane shall be laid using Butane Torch and sealing all joints etc, and preparing the surface complete. Apply second coat of Hot bitumen on the top of LEAKSHIELD. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 650/450N/5cm. Tear strength in longitudinal and transverse direction as 300/250N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane including Priming the surface with solvent based primer @ 200 gms/Sqm on the prepared surface. to complete the job as per Instructions of Engineer-In-Charge (a) Guarantee Bond to be furnished for 10 years warranty and performance Bank Guarantee for additional 10% of value of this item to be furnished before releasing of final bill and to be extended every year till the guarantee period of 10 years.(b) Provision of Pond test:- The contractor / applicator have to provide for the pond test on the terrace after the completion of sealing of joints for 48 hours. The water level will be a minimum depth of 100 mm at the junction of terrace and parapet wall i.e. the highest point on the terrace.

Finishing the waterproofing treatment with a coat of solar reflecting Bituminous Aluminum paint @ 150 gms/sqm to complete the job as per Instructions of Engineer-In-Charge

Y RAJA SHARMA

SRI SAI CONSTRUCTIONS

SWASTIK WATERPROOFING & CONSTRUCTION CONTRACTORS