Execution of Interior works including furniture, fitout works, cabling and other infrastructure work at Grand Rue, Ayur vigyan Nagar, August Kranti

Grand Total ( DSR Amount + 67,92,79,937.77

Grand Total 210018433.21

ABSTRACT OF COST

DETAILED ESTIMATE FOR THE CONSTRUCTION OF GRID INDIA

SH: INTERIOR WORKS

Refer RATE (DSR NON DSR AMOUNT (NON-

S.No. Office QUANTITY UNIT AMOUNT (DSR)

(DSR'23) '23) RATE DSR)

(SH: - 1.0 - CONCRETE WORK)

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached

pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping,

bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor all level, excluding the cost of

1 centering, shuttering and finishing : 47.00 47.00 cum 8482.00 398654.00

1:5:10 (1 Cement : 5 coarse sand (zone-III): 10 broken AAC 40 mm nominal size). 40 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and

2 4.1.3 shuttering - All work upto plinth level 1:2:4 (1 Cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 10.00 10.00 cum 7878.50 78785.00

mm nominal size)

Providing and laying in position ready mixed M-25 grade concrete for reinforced cement concrete work, using

cement content as per approved design mix, manufactured in fully automatic batching plant and transported to

site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of

specified grade for reinforced cement concrete work, including pumping of R.M.C. from transit mixer to site of

laying , excluding the cost of centering, shuttering finishing and reinforcement, including cost of admixtures in

recommended proportions as per IS : 9103 to accelerate/manufacturer's specifications/ approved design mix

retard setting of concrete, improve workability without impairing strength and durability as per direction of the

Engineer-in-charge.

(Note: Cement content considered in this item is 330 Kg/cum. Excess/less cement used as per design mix is

payable /recoverable separately)

b) All works above plinth level upto floor V level .

5.22A Steel reinforcement for R.C.C. work including straightening, cutting, bending,placing in position and binding

all complete above plinth level.

5.22A.6 Thermo-Mechanically Treated bars of grade Fe-500 or more. 5000.00 5000.00 kg 107.85 539250.00

5 Providing and fixing Following fasteners in RCC/ Brick work as per drawings.

MR M24 600 mm long chemical fastener Base plate for Col 12.00 12.00 each 2432.76 29193.00

6 MR M24 300 mm long chemical fastenerFace plates on Col 88.00 88.00 each 1405.00 123640.00

MR M12 mechnical fasteners 250 mm long 40.00 40.00 each 618.00 24720.00

TOTAL SUB HEAD -1 1111055.00 576207.00

Digitally signed by ANUJ

Abstract of Cost (Civil ) 3 GULIA

ABSTRACT OF COST

DETAILED ESTIMATE FOR THE CONSTRUCTION OF GRID INDIA

SH: INTERIOR WORKS

Refer RATE (DSR NON DSR AMOUNT (NON-

S.No. Office QUANTITY UNIT AMOUNT (DSR)

(DSR'23) '23) RATE DSR)

(SH: -2.0 - BRICK WORK)

Providing and laying autoclaved aerated cement blocks masonry with 100mm/150mm/200mm/230mm/250mm

thick or as desired size/ thickness AAC blocks conforming to IS 2185 Part 3 (1989) having density in oven dry

condition 551 - 650 Kg/Cum, Grade -I, minimum Compressive strength 4 N/mm2, thermal conductivity in air dry

condition 0.23 W/mK in super structure above plinth level up to all floor level with RCC band at sill level

7 6.47 and lintel level with approved block laying polymer modified adhesive mortar (minimum 3-4mm thick) all 100.00 100.00 cum 8333.65 833365.00

complete as per direction of Engineering-Charge. (The payment of RCC band and reinforcement shall be made

for separately).

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in super

8 6.13.2 structure above plinth including RCC band as required in 250.00 250.00 sqm 1123.80 280950.00

Cement mortar 1:4 (1 Cement : 4 coarse sand)

Extra for providing and placing including drilling where as requred in position 2 Nos. 6 mm dia M.S. bars at

9 6.15 every third course of half brick masonry 250.00 250.00 sqm 104.80 26200.00

TOTAL SUB HEAD -2 1140515.00 0.00

(SH: - 3.0 - WOOD WORK)

Providing factory made wood work in frames of doors, windows, clerestory windows and other frames, wrought

framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length including cut and

10 9.1.1 groove ( hold fast lugs or dash fastener shall be paid for separately). 6.00 6.00 cum 142949.70 857698.00

Natrual class teak wood

Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm dia double

threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 m dia polyamide PA 6

11 10.27.4 grade sleeve, including drilling of hole in frame , concrete/ masonry, etc. as per direction of Engineer-in-charge. 866.00 866.00 Each 182.20 157785.00

(Size-10x140mm)

Providing and fixing factory made ISI marked 40mm thick flush door shutters with both side of the door

decorative high pressure 1.0 mm thick laminated sheet of plain / wood grain in gloss / matt/ suede finish

with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046

Type S, including cost of adhesive of approved quality of approved shade and colour of approved make

conforming to IS : 2202 (Part I) core of block board construction with frame of 1st class hard wood and well

matched commercial 3 ply veneering with vertical grains or cross bands and face decorative laminate on both

12 MR faces of shutters including lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush 598.00 598.00 sqm 4595.00 2747810.00

door shutters : 40mm thick flush door shutters with both side decorative high pressure 1.0 mm thick laminated

sheet of plain / wood grain in gloss / matt/ suede finish including ISI marked Stainless Steel ball bearing hinges

with necessary ss screws complete with all respect as desired and direction of Engineer in charge.

Digitally signed by ANUJ

Abstract of Cost (Civil ) 4 GULIA

ABSTRACT OF COST

DETAILED ESTIMATE FOR THE CONSTRUCTION OF GRID INDIA

SH: INTERIOR WORKS

Refer RATE (DSR NON DSR AMOUNT (NON-

S.No. Office QUANTITY UNIT AMOUNT (DSR)

(DSR'23) '23) RATE DSR)

Providing and fixing stainless steel (grade 316) tower bolts ( nominal dia of sliding rod -10mm) of approved

make with necessary screws etc complete.

13 MR In stainless steel satin / polished finish 230.00 230.00 Each 518.70 119301.00

Providing and fixing stainless steel (grade 316) tower bolts ( nominal dia of sliding rod -10mm) of approved

make with necessary screws etc complete.

14 MR In stainless steel satin / polished finish 230.00 230.00 Each 518.70 119301.00

Providing and fixing bright finished 85-100 mm horizontal depth mortise latch and lock with six levers/ Euro

profile double cylinder in stainless steel satin finish and a pair of stainless steel lever handles of approved make

with necessary s.s. screws etc. complete as per direction of Engineer in charge.

Providing and fixing bright finished 85-100 mm horizontal depth mortise latch in stainless steel satin finish with

16 MR one dead bolt and pair of stainless steel (grade 304) lever handles with necessary s.s. screws etc. complete of 30.00 30.00 Each 3625.25 108758.00

approved make with necessary s.s. screws etc. complete as per direction of Engineer in charge.

Providing and fixing Stainless Steel (grade 304) floor door stoppers in stainless steel satin finish (Twin) of

17 MR approved make with necessary ss screws etc. complete as per direction of Engineer in charge. 115.00 115.00 Each 495.40 56971.00

Providing and fixing aluminum extruded section body tubular type universal hydraulic door closer (having brand

logo with IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to

1100 mm), with double speed adjustment with necessary accessories and screws etc. complete. The

manufacturer certificate for Life cycle of the door closer has to be 500000 cycle tested certificate has to be

submitted by agency) .

Providing and fixing wooden moulded beading to door and window frame with iron screws, plugs and priming

19 9.40.1.2 coat on unexposed surface etc. complete.( 2nd class teak wood) 648.00 648.00 metre 271.75 176094.00

50x20mm or 80x12.5mm as desired

Digitally signed by ANUJ

Abstract of Cost (Civil ) 5 GULIA

ABSTRACT OF COST

DETAILED ESTIMATE FOR THE CONSTRUCTION OF GRID INDIA

SH: INTERIOR WORKS

Refer RATE (DSR NON DSR AMOUNT (NON-

S.No. Office QUANTITY UNIT AMOUNT (DSR)

(DSR'23) '23) RATE DSR)

20 Toilet cubical made up of thermosetting resign treated high pressure, self-supporting 18mm thick decorative

compact laminates board of approved makes with permanently incorporate anti-bacterial agents during

manufacturing. Compact board should be resistance to water immersion through permissible increase on

thickness and mass <0.60% and board density >1.35kg/cm3 and fulfilled the criteria of FSC and green guard

gold certification and manufactured under EN438-2&3:2005 standard. 18mm thick compact board should be

Moisture resistant, Impact resistant, termite resistant ,Scratch resistant ,Weather and climatic shock resistant.

Finish of compact laminates should be suede finish which includes door, pilasters and intermediate panels

finished with approved texture/shades as per IS2046 and fulfilled the criteria of fire retardant under BS-476/97

and EN438-6 with classification of BS1D0 standard. Pilaster to be supported with SS(grade316) adjustable foot

and intermediate panels will attached to the wall with the help of approved SS(grade 316) channels and all

required hardware, made up of stainless steel as per manufacturer’s specification. Door knob, gravity hinges,

Thumb turn locksets with occupancy indicators, coat hooks with door stopper, U channel, top rail with corner

connector, adjustable foot/pedestal, Rubber noise deafening tape, screw & wall plugs should be approved under

the instruction of Engineer-in- charge. The top fitting should consist of SS. All screw will of 304 grade in SS with

stain finish. All pilasters are supported by SS bottom cladding. The base of the stainless steel bottom cladding

will be anchored to the floor with a clearance height upto 150 mm. Finish and colour of Toilet cubical should be

approved under guidance of engineer-in-charge.

Note: Only exposed area of laminated board in sqm shall be measured for payment purpose)

a) MR L-shape panel having door opening 600 mm 86.00 86.00 sqm 13260.00 1140360.00

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door

21 9.23 shutters/ (over all area of door shutter to be measured). 598.00 598.00 sqm 462.35 276485.00

Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded) (overall

22 9.24.1 area of door shutter to be measured) rectangular or square: 191.00 191.00 sqm 199.15 38038.00

23 9.26 Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured).: 456.00 456.00 sqm 106.70 48655.00

Providing and fixing in wall partition/lining medium density fibre board IS:14587:1998 marked, Pre-laminated one

side decorative lamination and other side balancing lamination, with necessary fixing arrangement and screws/

Digitally signed by ANUJ

Abstract of Cost (Civil ) 6 GULIA

ABSTRACT OF COST

DETAILED ESTIMATE FOR THE CONSTRUCTION OF GRID INDIA

SH: INTERIOR WORKS

Refer RATE (DSR NON DSR AMOUNT (NON-

S.No. Office QUANTITY UNIT AMOUNT (DSR)

(DSR'23) '23) RATE DSR)

Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing

and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120

gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm

and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm center to center with dash fastener of

12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48

mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges

of floor and ceiling channel and placed at a spacing of 610mm center to center by 6 mm dia bolts and nuts,

including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal

screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work

by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. .

The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of

99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two

boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish

with recommended jointing compound, jointing tape, angle beads at corner (25 mm x 25 mm x 0.5 mm), joint

finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in

charge all complete.

75 mm overall thickness full height partition with 12.5 mm thick double skin fire rated gypsum board of approved

make conforming to IS: 2095: part I

Dry wall (1) Full height Laminated partation

Supply & fixing (12+6)mm thick BWP board with 1.0mm laminate ( one side decorative lamination and other

side balancing lamination) dry wall double skin Partitions overall thickness 88mm thick upto false ceiling with

6mmx6mm thick groove as per approved design over MS tubular frame section 50mm x 50mmx1.60mm thick

including 50mm thick fiber glass wool insulation board ( 600x1200) wrapped in 200 G virgin polythene bags fixed

26 MR to wall/frame/ board with screw, rawl plug, insulation holders & washers having density 24 kg/ m3 confirming to 1889.00 1889.00 sqm 4286.00 8096254.00

IS: 8183, aluminium channel etc complete in all respect as per detailed drawings and direction Engineer in

charge.(For payment purpose one side area shall be measured .( only MS Frame shall be separately paid under

Dry wall (P2) Low Height partation ( 1200 MM Laminated + Abvoe 300 MM Height 12mm

Supply & fixing (12+6)mm thick BWP board with 1.0mm laminate ( one side decorative lamination and other

side balancing lamination) dry wall double skin Partitions overall thickness 88mm thick Low Height partation

with 6mmx6mm thick groove as per approved design over MS tubular frame section 50mm x 50mmx1.60mm

thick including 50mm thick fiber glass wool insulation board ( 600x1200) wrapped in 200 G virgin polythene

27 MR bags fixed to wall/frame/ board with screw, rawl plug, insulation holders & washers having density 24 kg/ m3 494.00 494.00 sqm 3927.00 1939938.00

confirming to IS: 8183 , 12mm thick toughened clear glass ( 300 height ) partation with aluminum frame, SS

channel, backer rod, silicon etc complete in all respect as per detailed drawings and direction Engineer in

charge. For payment purpose one side area shall be measured .( only MS Frame, glass shall be separately paid

under relevant item)

Digitally signed by ANUJ

Abstract of Cost (Civil ) 7 GULIA

ABSTRACT OF COST

DETAILED ESTIMATE FOR THE CONSTRUCTION OF GRID INDIA

SH: INTERIOR WORKS

Refer RATE (DSR NON DSR AMOUNT (NON-

S.No. Office QUANTITY UNIT AMOUNT (DSR)

(DSR'23) '23) RATE DSR)

Providing and fixing 12 mm thick frameless toughened glass door shutter/ Parations of approved brand and

manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making

28 21.18 necessary holes etc. for fixing required door fittings, all complete as desired and direction of Engineer-in-charge 40.00 40.00 sqm 5325.90 213036.00

(Door handle, lock and stopper etc.to be paid separately).

GLASS PARTATION

Single Glazed 12mm Toughened Glass Partition with dormakaba System 50 Frame Profiles

Supply and Fixing of Single Glazed Glass partition of 12mm Toughened Glass using dormakaba System 50

Frames to a height of maximum 3mtrs or as per drawing.The Fixed glass to be fixed using natural anodised

aluminium sections of size 50mm x 30mm . H Junction profile to be used at all Glass to Glass vertical joints, 90

Deg L Junction Profiles ,T Junction profiles . In case of Glass overall panel Overpanel Profile to be used.

29 MR The Profile shall be natural anodized, the Profile Manufacturer to supply all the necessary clips, seals and fixing 512.00 512.00 sqm 6689 3424768.00

accessories for the system.

All Profiles to be with minimum 1.5mm thickness and 20 microns of Anodizing/ poweder coating System should

meet Environmental product declaration (EPD).

SMART LAMINATED SWITCHABLE GLASS PARTATION

Supply and Fixing of Glass partition of extra clear toughened /heat strenghned Smart Laminated switchable

Glass (2 nos 5mm thick of 120 ppm extra clear toughened /heat strenghned glass + 4 nos 0.38mm thick PVB

interlayer + 1 layer 0.40mm thick smart film layer ) confirming to EN 356 standards. The SGG - Priva Smart

Laminated Glass should be able to confirm to a haze level of less than 6% during ON condition and 99% during

OFF condition. It should be able to provide an acoustic reduction of (RW (C;Ctr)) 36dB. The smart glass

assmebly should be IP68 rated. The Smart Glass system should be able to switch for 3 million cycles (ON/OFF).

(B) Supply and fixing of electrical cables (upto 20m).

The cables should be UL 2464 certified and the connectors should be IP67 certified.

(C) Supply and fixing of power supply units to control the smart glass.

30 MR The power supply units should confirm to electrical safety standard of EN 60335-1, EN 55014-1:2021, EN 61558- 35.10 35.10 sqm 132281 4643063.00

1 .The frame using dormakaba System 50 Frames to a height of maximum 3mtrs or as per drawing.The Fixed

glass to be fixed using natural anodised aluminium sections of size 50mm x 30mm . H Junction profile to be

used at all Glass to Glass vertical joints, 90 Deg L Junction Profiles ,T Junction profiles . In case of Glass overall

panel Overpanel Profile to be used.

All Profiles to be with minimum 1.5mm thickness and 20 microns of Anodizing/ poweder coating System should

meet Environmental product declaration (EPD).

Digitally signed by ANUJ

Abstract of Cost (Civil ) 8 GULIA

ABSTRACT OF COST

DETAILED ESTIMATE FOR THE CONSTRUCTION OF GRID INDIA

SH: INTERIOR WORKS

Refer RATE (DSR NON DSR AMOUNT (NON-

S.No. Office QUANTITY UNIT AMOUNT (DSR)

(DSR'23) '23) RATE DSR)

Single / double Leaf Aluminium Glazed Door of 12mm Toughened Glass with Frame Profiles

Supply & Fixing of Aluminium Glazed Door (Single Leaf) with Glass infill of 12 thk toughened glass with

dormakaba rebate door frame System with frame size 50 x 54mm Aluminium Stile door to be formed out of

70x35mm. Horizontal and Vertical Door Profile frame with clips & seals including Door Hardware - Flush

Hinges (4 Nos), Pure 8906 Lever Handle with 952 Narrow stile Lock package and dormakaba TS70 Slide Arm

Door closer with Hold Open unit complete with all respec as desired. Necessary seals to be provided all around

the door frames. The profiles shall be suitable for Glass thickness of 12mm. The Profile shall be matt natural

anodized finish, the Profile Manufacturer to supply all the necessary clips, seals and fixing accessories for the

All Profiles to be with minimum 1.5 mm Gauge thickness and 20 Micron of Anodizing.

Providing and fixing stainless steel handle H type ( grade 316 ) of approved make fixed with SS screws etc.

32 MR complete as per direction of Engineer-in-charge. 18.00 18.00 each 3249.00 58482.00

450mm @ 25 mm dia

Providing and fixing stainless steel grade 304 corner lock, strike plate and Euro Profile Cylinder of approved

33 MR make in glass door shutters etc with necessary accessories/screws etc. complete as per the directions of 18.00 18.00 Each 4644.00 83592.00

Engineer-in-charge.

TOTAL SUB HEAD -3

Digitally signed by ANUJ

Abstract of Cost (Civil ) 9 GULIA

ABSTRACT OF COST

DETAILED ESTIMATE FOR THE CONSTRUCTION OF GRID INDIA

SH: INTERIOR WORKS

Refer RATE (DSR NON DSR AMOUNT (NON-

S.No. Office QUANTITY UNIT AMOUNT (DSR)

(DSR'23) '23) RATE DSR)

(SH: - 4.0 - STEEL WORK)

AR over Structural steel (grade 350) work riveted, bolted or welded in built up sections, trusses and framed

34 DSR Item work,including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all 16740.00 16740.00 Kg 140.55 2352855.00

10.2 complete.

AR over Steel work (grade 350) in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including

DSR Item cutting, hoisting,fiXing in position and applying a priming coat of approved steelprimer, including welding and 18790.00 18790.00 Kg 201.25 3781541.00

10.16 bolted with special shaped washers etc. complete.

Electric resistance or induction butt welded tubes

AR over Providing and fixing M20 grade 8.8 bolts including nuts and washers complete as per drawing

10.25 Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a

priming coat of approved steel primer using structural steel etc. as required.

10.25.1 In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete

Supply & erection of Metal decking sheet as floor / roof decking with a crest height of 76 mm at a pitch distance

of 295 mm c/c having a cover width of 885 mm and with special emboss marks rolled into the profile for creating

bonding between concrete and steel decking. The steel feed material should of metal thickness of 1.20 mm

(including thickness of coating and galvanizing) galvanized to grade 180 (minimum) as per IS 277 of minimum

yield strength of 250 MPA of drawing grade as per IS:513, colour coated with total min. coating thickness of 30

38 MR microns (nominal) comprising of Regular modified polyester (RMP) paint of 16-20 microns (nominal) DFT on one 165.00 165.00 sqm 2773.00 457545.00

side over 5 microns (nominal) primer coat and 5 micron (nominal) primer coat on back surface, and of approved

profile, sectional properties (suitable for the specified loading/ deflection and purlins / runner spacing), colour and

shade, at all levels, including all labour, materials, handling, transportation, fasteners (including shear studs dia

19mm, length 125mm), scaffolding, equipment, end and side laps, cutting of openings, preparation of working

drawings, testing, etc., all complete, as per specifications, drawings and instructions of Engineer-in-Charge.

Digitally signed by ANUJ

Abstract of Cost (Civil ) 10 GULIA

ABSTRACT OF COST

DETAILED ESTIMATE FOR THE CONSTRUCTION OF GRID INDIA

SH: INTERIOR WORKS

Refer RATE (DSR NON DSR AMOUNT (NON-

S.No. Office QUANTITY UNIT AMOUNT (DSR)

(DSR'23) '23) RATE DSR)

Supplying and applying waterbased Fire intumescent paint, fire tested in accordance with BS 476 Parts 20-

22/UL/ASTM E 119/ISO 834-1 as selected and approved by the Engineer In charge of approved make. Fire

Paint DFT/ Fire Board Thickness dependent on HP/a or W/D or ISO 834-1 ratio of structural steel. Fire Paint to

use zinc phosphate primer to give additional anti-corrosive protection having VS of 73% - 83% as approved

applied over abrasive blasted surface and surface preparation up to a standard of Sa2.5 (ISO 8501-1:1988) or

SSPC-SP6 at 75 micron and GIRIHA/ LEEDV4 /Green Building norms Compliant for VOC Content and VOC

39 Emissions polyurethane finish paint as approved having volume solid of 72% - 73% or water based acrylic finish

@ 50 micron of the required shade over Structural Steel Works at all levels including storage, surface

preparation by sand blasting, degreasing, cleaning, drying, providing temporary staging, scaffolding, testing etc.,

all complete with all respect as desired and as per manufacturer specification and direction of Engineer in

charge. For Fire Proof Boards no surface preparation of any kind required on the steel surface for Fire Proof

Boards .Fire Proof board to have maximum average dry density of 220 Kgs/cubic mt , minimum compressive

strength @10% of 35 KN/sq mt ,

Maximum moisture absorption of 1% by volume, Corrosion and Fungal resistance. Fire Proof Boards to be cut in

desired size and fixed on the beams and columns as per manufacturer installation manual using manufacturer

approved screws and fittings all complete with all respect as desired and as per manufacturer specification and

MR direction of Engineer in charge. 440.00 440.00 sqm 5109.00 2247960.00

The above products should confirm to GIRIHA/ LEEDV4 /Green Building norms. Application to be carried out by

authorized manufacturer applicator or any other trained applicator as approved by the manufacturer and direction

of Engineer in charge.

Providing firefixing

and ratingframe work for partitions/ wall lining etc. made of 50x50x1.6 mm hollow MS tube, placed

along the walls, ceiling and floor in a grid pattern with spacing @ 60 cm centre to centre both ways (vertically &

horizontally) or at required spacing near opening, with necessary welding at junctions and fixing the frame to

wall/ ceiling/ floors with steel dash fasteners of 8 mm dia, 75 mm long bolt, including making provision for

40 9.154 opening for doors, windows, electrical conduits, switch boards etc., including providing with two coats of 28596.00 28596.00 Kg 166.80 4769813.00

approved steel primer etc. complete, all as per direction of Engineer-in-charge..

Digitally signed by ANUJ

Abstract of Cost (Civil ) 11 GULIA

ABSTRACT OF COST

DETAILED ESTIMATE FOR THE CONSTRUCTION OF GRID INDIA

SH: INTERIOR WORKS

Refer RATE (DSR NON DSR AMOUNT (NON-

S.No. Office QUANTITY UNIT AMOUNT (DSR)

(DSR'23) '23) RATE DSR)

(SH: - 5.0 - FLOORING WORK)

Kota stone slab flooring over 20mm (average) thick base laid over and jointed with grey cement slurry mixed

with pigment to match the shade of the slab including rubbing polishing and groove complete with base of

25 mm thick (Size of stone 1200 mm x 600 mm )

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement

42 11.27 mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade 20.00 50.00 sqm 2354.70 117735.00

of the slabs, including rubbing polishing and groove complete.

Providing and laying modular carpet of approved make and shade and made with 100% solution dyed nylon

6/6.6 tufted textured tip sheared/ cut & loop piles, tiles of minimum 500mm x 500mm in size, stain resistant, anti

microbial, and having colour fastness to water, fastness to light, rubbing fastness and castor chair suitability as

per relevant standard for heavy commercial usage, with Non PVC / Recycled PVC backing, nominal total

thickness of minimum 6.50 mm, pile height minimum 3.4 mm, minimum Total Pile weight – 680gm/sqm).

43 MR Material shall be CRI GREEN LABEL PLUS certified, and shall have recycled content complying to GRIHA 933.00 933.00 sqm 3703.00 3454899.00

requirement, including fixing with GRIHA compliant adhesive of approved make, minimum 15 years

manufacturer's warrantee, all complete as per drawings, manufacturer's specifications and direction of Engineer

Providing and laying full body / homogenous Vitrified tiles of approved make ( Polish / satin Finish/ anti skid/

Matt) in flooring with different sizes ( thickness to be specified by the manufacturer),with water absorption less

than 0.08% and confirming to IS; 15622, of approved brand & manufacturer, in all colours and shade, laid with

44 cement based high polymer modified quick set tile adhesive ( water based ) conforming to IS; 15477 , in average

6-10 mm thickness, including grouting of joints .( payment for grouching of joints to be made separately)

Providing and laying Vitrified tiles of approved make in different sizes (thickness to be specified by the

manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand &

manufacturer, in all colours and shade, in skirting, riser of steps,dado laid with cement based high polymer

45 modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including

grouting of joints .

Polish finish vitrified tile

Providing and laying tactile tile (for vision impaired persons as per standards) of size 300x300x9.8mm having

with water absorption less than 0.5% and conforming to IS:15622 of approved make in all colours and shades in

for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement

46 16.90 mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement 50.00 50.00 sqm 2017.60 100880.00

mixed with matching pigments etc. complete as per direction of Engineer-in-Charge.

Digitally signed by ANUJ

Abstract of Cost (Civil ) 12 GULIA

ABSTRACT OF COST

DETAILED ESTIMATE FOR THE CONSTRUCTION OF GRID INDIA

SH: INTERIOR WORKS

Refer RATE (DSR NON DSR AMOUNT (NON-

S.No. Office QUANTITY UNIT AMOUNT (DSR)

(DSR'23) '23) RATE DSR)

Providing and fixing 18mm thick gangsaw cut mirror polished (premoulded and prepolished) machine cut for

kitchen platforms, vanity counters ,window sills , facias and similar locations of required size of approved shade,

colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated

with white cement, mixed with matching pigment, epoxy touch ups, including rubbing,groove making, curing,

47 8.2.2.2 moulding and polishing to edge to give high gloss finish etc. complete at all levels.. 50.00 50.00 sqm 5136.30 256815.00

(Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent as approved)

Granite of any colour and shade (Area of slab over 0.50 sqm)

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity

48 8.5 counter and similar location in marble/ stone work including necessary holes for pillar tabs etc including rubbing 28.00 28.00 Each 978.70 27404.00

& polishing of cut edges etc complete

Providing and fixing machine cut, mirror/ eggshell polished , granite stone work for wall lining (veneer work) ,

dado,cladding, skirting, risers of steps etc., in required design and pattern wherever required, stones of

different finished surface texture, with average 10mm thickness high polymer modified quick set adhesive (white

Based on base) of make Weber of m/s Saint Gobian /Ferrouscrete / MYK Laticrete or equivalent laid and jointed with

DSR-11.27 white cement slurry @ 3.3 kg/sqm including pointing with white cement slurry admixed with pigment of matching

shade, including groove ,rubbing, curing, polishing etc. all complete as per Architectural drawings, and as

directed by the Engineer-in-Charge.( Basic rate of granite stone -1800/- per sqm )

18mm thick Granite in all shade / colour / size (Area of slab over 0.50 sqm) as approved by Engineer in charge.

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand ( Zone III) : 4 graded stone aggregate) finished with a

50 11.3.1 floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 933.00 933.00 sqm 614.20 573049.00

40 mm thick with 20 mm nominal size stone aggregate

Grouting the joints of flooring / Wall tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic

coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and

51 11.48.2 finishing complete as per direction of Engineer-in-charge. 5462.00 5462.00 sqm 309.05 1688031.00

600mm x 600mm/ 300x600 tiles

Providing & fixing in position Phenol bonded Bamboowood in wall skirting with planks of sizes 14mm thick,

1900mm length (minimum) and 85mm wide(minimum), in approved colour, texture and finish, having

Performance Appraisal Certificate (PAC) issued by Building Materials & Technology Promotion Council

(BMTPC). The skirting shall be fixed with SS screws & rawl plugs, over underlayment of 4mm thick, expanded

52 26.2 polyethylene foam sheets having 40kg/cum density over prepared surface. The bamboowood planks shall have 84.97 84.97 sqm 6033.55 512659.00

minimum density of 1000Kg/cum & minimum Hardness 1000 Kgf. with Eco friendly UV coating, all complete as

per direction of the Engineer in-charge.

Providing and fixing removable raised/false access flooring with system and its components of approved make

for different plenum height with possible height adjustment upto 50 mm, comprising of modular load bearing floor

53 panels supported on G.I. rectangular stinger frame work and G.I. Pedestal etc. all complete, as per the

architectural drawings, as specified

and as directed by Engineer-in-charge consisting of :

Digitally signed by ANUJ

Abstract of Cost (Civil ) 13 GULIA

ABSTRACT OF COST

DETAILED ESTIMATE FOR THE CONSTRUCTION OF GRID INDIA

SH: INTERIOR WORKS

Refer RATE (DSR NON DSR AMOUNT (NON-

S.No. Office QUANTITY UNIT AMOUNT (DSR)

(DSR'23) '23) RATE DSR)

a) Providing at required spacing to form modular framework, pedestals made out of GI tube of thickness

minimum 2 mm and 25 mm outer diameter, fully welded on to the G.I. Base plate of size 100mm x 100mm x

3mm at the bottom of the pedestal tube, G.I. pedestal head of size 75mmx75mmx3.5 mm welded with GI fully

threaded stud 16mm outer diameter with two GI Check nuts screwed on the stud for level adjustment upto

50mm, locking and stabilizing the pedestal head in position at the required level. The pedestals shall be fixed to

the subfloor (base) through base plate using epoxy based adhesive of approved make or the machine screw with

b) Stringers system in all steel construction hot dipped galvanized of rectangular size 570x20x30x0.80mm thick

having holes at both ends for securing the stringers on to the pedestal head using fully threaded screws ensuring

maximum lateral stability in all directions, the grid formed by the pedestal and stringer assembly shall receive the

floor panel, this system shall provide adequate solid, rigid support for access floor panel, the system shall

provide a minimum clear uninterrupted clearance between the bottom of the floor for electrical conduits and

wiring etc. all complete as per the architectural drawings, as specified and as directed by the Engineer-in charge.

c) Providing and fixing Access Floor panel of 600x600x32 mm medium grade Filled Steel anti static high

pressure Lamination of . Access Floor panel shall be steel welded construction with an enclosed bottom pan with

uniform pattern of 64 hemispherical cones. The top and bottom plates of Steel Gauges: top 0.6 mm and bottom

0.7 mm fused spot welded together (minimum 64 welds in each dome and 20 welds along each flange). The

panel should be corrosion resistant epoxy coated for lifetime rust protection and cavity formed by the top and

bottom plate is filled with non combustible Portland cementitious core mixed with lightweight foaming

compound. The access floor shall be factory finished with Anti-static High Pressure laminate with Non Warp

technology upto 1mm thickness for superior adhesion and Surface flatness within 0.75mm. The panel is to

withstand a Concentrated Load of 363 kgs applied on area 25mm x 25mm without collapse in the centre of the

panel which is placed on four steel blocks. The panel will withstand and Uniformly Distributed Load (UDL)

minimum 1250 kg/sqm and an impact load of 50kg all complete as per the approved manufacturers specification

and as per the direction of Engineer-in-charge. All specification must be printed on the side of the panel to

ensure the quality of the product.

11.54.2 450 mm Finished Floor Height (FFH). 153.00 153.00 sqm 5977.35 914535.00

Providing & Fixing flexible PVC vinyal sheet sports flooring of approved make in 6.5 mm thickness( minimum ) in

the size of 2mx20-23mtr . Results from independent testing demonstrate that product inherently inhibits the

growth of microbial strain MRSA. It shall be homogeneous in construction. The flooring shall incorporated a

specially formulated polyurethane reinforced to give lifetime polish free maintenance. Imported PVC Vinyl

flooring static electrical charge < 2kv,impact sound reduction approx ,good resistance of scratch, slip, chemical

and fire doesn't favor in growth of fungi & bacteria , Material should 100% recyclable and at least 25% recycled

materials complete with all respect and as per manufacturer specifications & direction of Engineer in charge. .

Digitally signed by ANUJ

Abstract of Cost (Civil ) 14 GULIA

ABSTRACT OF COST

DETAILED ESTIMATE FOR THE CONSTRUCTION OF GRID INDIA

SH: INTERIOR WORKS

Refer RATE (DSR NON DSR AMOUNT (NON-

S.No. Office QUANTITY UNIT AMOUNT (DSR)

(DSR'23) '23) RATE DSR)

(SH: - 6.0 - ROOFING / FALSE CEILING WORK)

Providing and fixing GI Clip in Metal Ceiling System of approved make of 600x600/ 600x1200 mm module

which includes providing and fixing ‘C’ wall angle of size 20x30x20 mm made of 0.5 mm thick pre painted steel

along the perimeter of the room with help of nylon sleeves and wooden screws at 300 mm center to centre,

suspending the main C carrier of size 10x38x10 mm made of G.I steel 0.7 mm thick from the soffit with help of

soffit cleat 37x27x25x1.6 mm, rawl plugs of size 38x12 mm and C carrier suspension clip and main carrier

bracket at 1000 mm c/c. Inverted triangle shaped Spring Tee having height of 24 mm and width of 34 mm made

of GI steel 0.45 mm thick is then fixed to the main C carrier and in direction perpendicular to it at 600 mm

centers with help of suspension brackets. Wherever the main C carrier and spring T have to join, C carrier and

55 12.54.2 spring T connectors have to be used. All sections to be galvanized @ 120 gms/sqm (both side inclusive),fixing 600.00 600.00 sqm 2354.65 1412790.00

with clip in tiles into spring ‘T’ with :

GI Metal Ceiling Clip in plain Beveled edge global white color tiles of size 600x600/600x1200 and 0.5 mm thick

with 25 mm height, made of G I sheet having galvanizing of 100 gms/ sqm (both sides inclusive) and 20%

perforation area with 1.8 mm dia holes and having NRC of 0.5, electro statically polyester powder coated of

thickness 60 microns (minimum), including factory painted after bending and perforation.

Providing and fixing GI Clip in Metal Ceiling System of approved make of 600x600/ 600x1200 mm module

which includes providing and fixing ‘C’ wall angle of size 20x30x20 mm made of 0.5 mm thick pre painted steel

along the perimeter of the room with help of nylon sleeves and wooden screws at 300 mm center to centre,

suspending the main C carrier of size 10x38x10 mm made of G.I steel 0.7 mm thick from the soffit with help of

soffit cleat 37x27x25x1.6 mm, rawl plugs of size 38x12 mm and C carrier suspension clip and main carrier

bracket at 1000 mm c/c. Inverted triangle shaped Spring Tee having height of 24 mm and width of 34 mm made

of GI steel 0.45 mm thick is then fixed to the main C carrier and in direction perpendicular to it at 600 mm

centers with help of suspension brackets. Wherever the main C carrier and spring T have to join, C carrier and

spring T connectors have to be used. All sections to be galvanized @ 120 gms/sqm (both side inclusive),fixing

with clip in tiles into spring ‘T’ with :

GI Metal Ceiling Clip in plain Beveled/tegular edge global white color tiles of size 600x600/600x1200mm and 0.5

mm thick with 25 mm height, made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and

electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after

Digitally signed by ANUJ

Abstract of Cost (Civil ) 15 GULIA

ABSTRACT OF COST

DETAILED ESTIMATE FOR THE CONSTRUCTION OF GRID INDIA

SH: INTERIOR WORKS

Refer RATE (DSR NON DSR AMOUNT (NON-

S.No. Office QUANTITY UNIT AMOUNT (DSR)

(DSR'23) '23) RATE DSR)

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special

sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive)

as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and

37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long

with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with

nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm

running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of

80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in

a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm

long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of

20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm

57 centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section

and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and

finishing to a flush finish of tapered and square edges of the board with recommended jointing compound ,

jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two

coats of primer suitable for board, all as per manufacturer’s specification and also including the cost of making

openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed,making

cove & slit etc, all complete as per detailed drawings, specification and direction of the Engineer in Charge but

excluding the cost of painting with :-

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) : 2011 (Board with BIS

a) 12.45.1 certification marks) of approved make or equivalent as approved). 2040.34 2040.34 sqm 1355.80 2766293.00

b) 12.45.3 12.5 mm thick tapered edge gypsum moisture resistant board. 22.00 22.00 sqm 1529.10 33640.00

Digitally signed by ANUJ

Abstract of Cost (Civil ) 16 GULIA

ABSTRACT OF COST

DETAILED ESTIMATE FOR THE CONSTRUCTION OF GRID INDIA

SH: INTERIOR WORKS

Refer RATE (DSR NON DSR AMOUNT (NON-

S.No. Office QUANTITY UNIT AMOUNT (DSR)

(DSR'23) '23) RATE DSR)

Mineral Fiber Anti-microbial false ceiling :

Providing and fixing mineral fibre false ceiling tiles of approved make at all heights of size 595X595mm of

approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light

Reflectance > 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in

true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm

thick (galvanized @120 gsm) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size

15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form

grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised @ 80

gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000

mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’.

58 26.27.2 The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size 1441.54 1441.54 sqm 2671.20 3850642.00

24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm

centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false

ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried

out as per CPWD specifications, drawings and as per directions of the engineer-in charge.

All work shall be done with fully perforated 16 mm thick beveled tegular mineral fiber Anti-microbial false ceiling

tile confirming to ISO-5 ( CLASS 100) specification.

Tounge & Groove wooden laminated False Ceiling:-

Providing & fixing Tounge & Groove Wooden Laminated False Ceiling (HPL-Mica) of per approved make of

size- 190 mm X 2440 X 12 mm in true horizontal level suspended on interlocking White/Black 'T'-Grid hot

dipped galvanized iron section of 0.30 mm thick (galvanized @120 gsm) comprising of main T runners of 24 x32

mm of length 3000 mm. The second 'T' should be hanged at an Interval of 450 mm from first main'T'.

Suspension of 'T'Grid from ceiling using galvanized mild steel item (galvanised@80gsm) M-6 dash fasteners, 6

mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm,

spaced at 600 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the

help of GI perimeter wall angle of size 22 mm x 22 mm X 3000 mm made of 0.40 mm thick sheet, to be fixed to

the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The

Wooden Panel made of High Density Fiber Board (HDMR) Substrate with HPL facing as per the approved

Shade/species and finish and a Melamine balancing layer over the reverse side. The density of HDMR board

should be more than 800kg/m3 . The HDMR board should be passed through vertically flammability test (UL94)

& should be tested as for Anti-Fungal. The work shall be carried out as per specifications, drawings and as per

directions of the Engineer-In-Charge.

Digitally signed by ANUJ

Abstract of Cost (Civil ) 17 GULIA

ABSTRACT OF COST

DETAILED ESTIMATE FOR THE CONSTRUCTION OF GRID INDIA

SH: INTERIOR WORKS

Refer RATE (DSR NON DSR AMOUNT (NON-

S.No. Office QUANTITY UNIT AMOUNT (DSR)

(DSR'23) '23) RATE DSR)

ACOUSTICAL GLASS FIBER FALSE CEILING - SOUNDSCAPES

Providing and Fixing SoundScpaes Acoustical blades which are 40 mm thick, flat glass fibre panels as approved

make with Humidity Resistance RH 90%, with factory fitted embedded metal insert with ¼” – 20 threading for

fixing cable adjuster for hanging application. Acoustical blades shall have sizes of 200x1200mm, 200x1600mm

with 200mmC/C distance, with both side laminated scrim finished with uniform water based paint on all surface

(including edges). Acoustical performance of upto 0.65 NRC) as per ASTM C-423 (Average value of Absorption

Co-efficient readings taken at 250 Hz, 500 Hz, 1000 Hz and 2000 Hz) in standard White color with Light

reflectance 87% or in the color specified by the Architect (Shell / Tangerine / Cranberry / Moss / Kiwi / Reef /

Lagoon), Fire Performance Class B2 – s1, d0 as per EN 13501-1 .The blade shall be made of Glass fibre panel

with density of 110-120 Kg/ m3. SUSPENSION: The panel shall be hung using hanging kit comprising of griper

structure anchor & cap of dia 20mm, spring loaded bottom end cable adjuster of dia. 9mm and 2.4m long aircraft

cable of 1/16” dia. Components 1) Griper structure anchor 2) Gripper anchor cap 3) Cable adjuster 4) Aircraft

Cable Cable adjuster Spring loaded bottom end cable adjuster of dia. 9mm and 45mm long Aircraft cable

60 MR Material Galvanized Steel Aircraft cable dimension 1/16” Ø x 2.4m Tolerance ±1mm. INSTALLATION:Hanger 154.00 154.00 sqm 9292.00 1430968.00

Wire Attachment to Structure: Attach the gripper structure anchor to the structure with an appropriate fastener

(1/4"-20 Threading) that will carry the full weight of the blades. Insert the end of the cable into the gripper anchor

cap. Screw the gripper anchor cap completely into the gripper structure anchor. Insert Suspension Cables: The

panel is to be suspended using the aircraft cables which are suspended from the soffit using the gripper

structure anchors and its other end passing through the bottom end cable adjuster. The height & level of the

panels can be adjusted using the bottom end cable adjusters.Suspension of Blade: Locate the two factory fitted

female inserts on the blades. Suspend the Blades by screwing the bottom end of the cable adjuster into the

female inserts. Installation should be carried out as per Manufacturer recommended procedure.

Digitally signed by ANUJ

Abstract of Cost (Civil ) 18 GULIA

ABSTRACT OF COST

DETAILED ESTIMATE FOR THE CONSTRUCTION OF GRID INDIA

SH: INTERIOR WORKS

Refer RATE (DSR NON DSR AMOUNT (NON-

S.No. Office QUANTITY UNIT AMOUNT (DSR)

(DSR'23) '23) RATE DSR)

Providing and Fixing Channelled Woodworks perforated panels approved make of width 192mm, thickness of

15mm and length 2400 mm, made of a Moisture resistant fibre board substrate with a laminated facing as per

the approved shade (Portland Maple, Sea Beech, Siam Wood & Mystique Walnut, Interior White, Alumina Pearl)

and a melamine balancing layer on the reverse side. The boards shall have a special perforation pattern where

the reverse surface has a “Helmholtz” fluted perforation with consecutive 3mm wide groove followed by 5mm of

visible pane. The edges of the panel shall be “tongue-and-grooved” to fix special clips for installation and

seamless visual. The back of the perforated panel shall have sound absorbing non-woven Soundtex acoustical

fleece hot pressed to achieve NRC of 0.65. (Average value of Absorption Co-efficient readings taken at 250 Hz,

500 Hz, 1000 Hz and 2000 Hz) as per ASTM C423 and Humidity Resistance (RH) of 70% with camber limit less

than 1mm/1000mm and bow less than 1mm/300mm.The panels shall be mounted on special aluminium splines

(keel) using inside clips provided by Knauf and approved by the Architect/ Engineer-in-Charge.

Properties of TileRelevant Standards

Base MaterialMoisture Resistant Medium Density Fibre board

61 Panel Dimensions2400mm x 192mm x 15mm

Panel Weight≅ 8.5kgs/m2

Perforation Details “Helmholtz” fluted perforation on reverse side with consecutive of 3mm wide groove followed

by 5mm of visible pane.

Panel Finish Laminate (Portland Maple, Sea Beech, Siam Wood & Mystique Walnut, Interior White, Alumina

Pearl) finish Noise Reduction Co-efficient 0.65 ASTM C423 (Average value of Absorption Co-efficient readings

taken at 250 Hz, 500 Hz, 1000 Hz and 2000 Hz)

Humidity ResistanceRH 70%

Dimensional tolerances± 5mm

Digitally signed by ANUJ

Abstract of Cost (Civil ) 19 GULIA

ABSTRACT OF COST

DETAILED ESTIMATE FOR THE CONSTRUCTION OF GRID INDIA

SH: INTERIOR WORKS

Refer RATE (DSR NON DSR AMOUNT (NON-

S.No. Office QUANTITY UNIT AMOUNT (DSR)

(DSR'23) '23) RATE DSR)

The panel shall be mounted by tongue and groove mechanism using inside clip on Knauf aluminium extruded

keel made of Grade 6063-T5 having dimensions 3000(L) x 24(H) x 15.5(W). The keel shall also be used for

transition of the butt end of adjacent panel at every 7.2m.

Installation System Details

Aluminium Keel/ Transition Profile

Base MaterialExtruded Aluminium Grade 6063-T5

Construction MethodAluminium Extrusion

Dimensions3000(L) x 24(H) x 15.5(W) mm

Clip Inside Clip

An appropriate vapour barrier (by others) shall be applied/installed on the vertical surface before the installation

to properly seal against entry of any moisture. Vapour barrier (by others) shall be installed as per Manufacturer’s

recommendation. Install wooden batten grid (provided by others) of section 50x50mm or as approved by the

Architect on the solid wall/partition to provide level and plumb surface for fixing Knauf Keel. Install Keel vertically

using screws and plugs at spacing of not more than 600mm centre-to-centre. The first and last keel should not

be more than 150mm from the ends. Trim the tongue of the first bottom panel and install using headless nail

with groove side upward. Subsequent panels are installed with tongue side downward by engaging with each

other using tongue and groove mechanism and secured by inside clip. Continue this process until required

height is achieved. Shorter butt edges need to be joined using industrial/wood glue. The keel shall also be used

for transition of the butt end of adjacent panel at every 7.2m. Install the skirting (provided by others) of width

50mm or more as required by the Architect/ Engineer-in-Charge. Finish off the edges using wooden moulding of

matching colour (by others). Installation should be carried out as per Knauf recommended procedure. .

Providing & fixing in position Phenol bonded Bamboowood in wall cladidng at all heights with planks of sizes 10

mm thick, minimum 1800 mm length and minimum 100 mm wide, in approved colour, texture and finish, having

Performance Appraisal Certificate (PAC) issued by Building Materials & Technology Promotion Council

(BMTPC), with necessary profiled edges fixed with40 mm SS Screws 5 nos in each tile to framework made of

second class teakwood of size 20 x 15 mm in centre of each tile and bottom & top of work height, 40 x 15 mm

placed at end of each tile> The cladding shall be laid over back layment of 1.00 mm thick expanded polythyline

foam of density 40 kg/sqm in two layers, first layer on wall surface before fixing wooden frame and second layer

on frame under cladding. The bamboowood planks shall have minimum density of 1000Kg/cum & minimum

Hardness 1000 Kgf. with Eco friendly UV coating, all complete as per direction of the Engineer in-charge.

Digitally signed by ANUJ

Abstract of Cost (Civil ) 20 GULIA

ABSTRACT OF COST

DETAILED ESTIMATE FOR THE CONSTRUCTION OF GRID INDIA

SH: INTERIOR WORKS

Refer RATE (DSR NON DSR AMOUNT (NON-

S.No. Office QUANTITY UNIT AMOUNT (DSR)

(DSR'23) '23) RATE DSR)

Providing and Fixing of Veneer Ply paneling ( 18 marine ply / board + 4mm thk veneer ) Over columns and walls

using Aluminium /MS frame and melamine polish and 4mm x4mm grooves . Panelling shall consist of approved

MS frame 50x25x1.6 mm sections and 600x600 mm centres to centers in both the directions as required

covered with 18 mm thick approved brand marine ply/ board with necessary 4x4 mm thick vertical and horizontal

grooves and 80 mm x 12 mm rubberwood/ steambeach half round moulding and finished with approved shade

63 MR matt melamine polish finished. The item shall be completed including making cut outs for electrical switches and 241.00 241.00 sqm 8319.00 2004879.00

appliances , Polish etc. as per detail drawings. The framework shall be anchored using anchor fastners and

screws etc. Complete in all respect as desierd and directed by the Engineer in charge / Consultant of work at

Providing and fixing wall/column paneling with 18 marine ply / board + 1mm thick decorative laminate as

approved shade /colour( one side decorative lamination of approved shade and other side balancing lamination)

and conforming to IS; 12823 grade I Type II with internal Kiln seasoned and chemically treated hollock wood

hard wood frame of adequate and approved section and size. Hard wood framework shall be treated with anti-

64 MR termite and fire retardant paint. All the edges of board should be eased with maple wood, including making cut 889.00 889.00 sqm 8028.00 7136892.00

outs for electrical switches and appliances etc., all complete as per architectural drawings and direction of

Engineer in Charge

Digitally signed by ANUJ

Abstract of Cost (Civil ) 21 GULIA

ABSTRACT OF COST

DETAILED ESTIMATE FOR THE CONSTRUCTION OF GRID INDIA

SH: INTERIOR WORKS

Refer RATE (DSR NON DSR AMOUNT (NON-

S.No. Office QUANTITY UNIT AMOUNT (DSR)

(DSR'23) '23) RATE DSR)

ACOUSTICAL WALL PANEL IN FABRIC FINISH

Providing and Fixing of Acoustical Wall Panel with square edges made of fiber glass substrate 25mm thick,

Acoustical Wall Panel as approved make shall be of custom made sizes and per design ( subject to

manufacturing Limitations, need to check from manufacturer first) wrapped on the front side with an acoustically

transparent fabric as per the approved shade (Husk, Copper, Sangria, Sesame, Coffee, Charcoal, Titanium,

Flame, Peanut and Shell). The panel shall be classified for Fire Class A, as per ASTM E-84. The Acoustical Wall

Panel shall be of sizes 600x600mm (Nominal) or 600x1200mm (Nominal) and shall achieve an NRC of 0.85

(Average value of Absorption Co- efficient readings taken at 250 Hz, 500 Hz, 1000 Hz and 2000 Hz) with 50mm

airgap as per ASTM C423 to be fixed to wall on a framework of wooden battens and using Wall panel Impalers

(supplied by the manufacturer) or by using construction adhesives (as per the instructions laid down by the

65 MR manufacturer). The fiber glass substrate shall have a recycle content of 85%. INSTALLATION: An appropriate 150.00 150.00 sqm 7444.00 1116600.00

vapour barrier (by others) shall be applied/installed on the vertical surface before the installation to properly seal

against entry of any moisture. Vapour barrier (by others) shall be installed as per Manufacturer’s

recommendation. Install wooden batten grid (provided by others) of section 50x50mm or as approved by the

Architect on the solid wall/partition to provide level and plumb surface. The Impalers shall be fixed to the battens

using self- tapping screws. Silica based construction adhesive (by others) to be dabbed on to the projecting

elements (spikes) of the Impalers. Wall Panels shall be pierced through the spikes of the Impalers ensuring the

line and level of the panels are maintained.

Providing & fixing first class teak wood skirting of size 25 x 150mm to be installed on GI Studs (50mmx50mm)

.5mm thickness or better including polyurethene polish complete as per drawing and to the entire satisfaction of

66 MR Engineer-in-charge/Architect. Complete in all respect as desierd by the Engineer in charge / Consultant of work 250.00 250.00 metre 827.00 206750.00

Digitally signed by ANUJ

Abstract of Cost (Civil ) 22 GULIA

ABSTRACT OF COST

DETAILED ESTIMATE FOR THE CONSTRUCTION OF GRID INDIA

SH: INTERIOR WORKS

Refer RATE (DSR NON DSR AMOUNT (NON-

S.No. Office QUANTITY UNIT AMOUNT (DSR)

(DSR'23) '23) RATE DSR)

(SH: - 7.0 - FINISHING WORK)

6 mm plaster on cement concrete or reinforced cement concrete work with white cement based polymer

67 13.86 modified self curing mortar of approved make including making groove where ever required as per the direction 965.00 965.00 sqm 269.15 259730.00

of Engineer-In-Charge :

12 mm cement plaster of mix :

68 13.4.2 1:6 (1 Cement : 6 Coarse sand) including groove where ever required 850.00 850.00 sqm 343.65 292103.00

15 mm cement plaster on the rough side of single or half brick wall of mix :

69 13.5.2 1:6 (1 Cement : 6 Coarse sand) including groove where ever required 850.00 850.00 sqm 395.35 336048.00

Painting with synthetic enamel paint of approved of approved make brand and manufacture to give an even

70 13.62.1 shade. Two or more coats on new work 50.00 50.00 sqm 226.25 11313.00

Finishing with Epoxy paint (two or more coats) of approved make at all locations prepared and applied as per

71 13.52.1 manufacturer’s specifications including appropriate priming coat, preparation of surface, etc. complete.( a) on 100.00 100.00 sqm 241.75 24175.00

Providing and applying white cement based putty of approved make average thickness 1mm minimum two coat

72 13.80 ,of approved brand and manufacturer ,over the plastered wall surface to prepare the surface even and smooth 3165.00 3165.00 sqm 156.05 493898.00

Wall painting with premium acrylic emulsion paint of approved make of interior grade having VOC ( Volatile

Organic Compound ) content less than 50grams/litre of approved brand and manufacturer, including applying

73 13.83.2 additional coats wherever required to achieve even shade colour. 3165.00 3165.00 sqm 142.80 451962.00

Two or more coats on new work

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections as per direction of

Applying priming coats with primer of approved brand and manufacture of approved make , having low VOC (

75 13.85.3 Volatile Organic Compound) content with water thinnable cement primer on wall surface having VOC content 3165.00 3165.00 sqm 73.95 234052.00

less than 50grames/ litre.

Providing and applying 12 mm thick (average) premixed formulated one coat gypsum lightweight plaster of

approved make having additives and light weight aggregates as vermiculite/ perlite respectively conforming to

76 13.78 IS: 2547 (Part - 1 & II) 1976, applied on hacked / uneven background such as bare brick/ block/ RCC work on 500.00 500.00 sqm 468.90 234450.00

walls & ceiling at all floors and locations, finished in smooth line and level etc. complete.

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of

approved manufacturer, of required shade and colour all complete :

77 13.41.1 New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC 2665.00 2665.00 sqm 185.65 494757.00

content less than 50 gram/litre

Melamine polishing on wood work

Digitally signed by ANUJ

Abstract of Cost (Civil ) 23 GULIA

ABSTRACT OF COST

DETAILED ESTIMATE FOR THE CONSTRUCTION OF GRID INDIA

SH: INTERIOR WORKS

Refer RATE (DSR NON DSR AMOUNT (NON-

S.No. Office QUANTITY UNIT AMOUNT (DSR)

(DSR'23) '23) RATE DSR)

Providing and applying water-based special two-tone velvet/ Preimistic Pearl finish of interior grade having low

VOC made up of special pearl pigments of make as approved by engineer in charge having special wipeable

properties and finish to be equivalent to :- a. Damascus/Alba/Palmyra of UltraTech (UTTPL) or equivalent as

approved, b. Perlata of Armour Coat c. R-Stone fondo of Nova Color The finish should have anti-algae and UV

resistance properties in the desired pattern after scrapping and properly cleaning the surface to remove loose

particles from the plastered surface. The following process to be followed : a. Initial coat of Masonry primer of

79 MR approved colour and shade ( Min. 0.9 ltr /10 sqm). b. Two coats of base coat with roller and brush ( Min. 0.9 ltr 392.00 392.00 sqm 2287.00 896504.00

/10 sqm). c. Final finish in 2 coats of Preimistic pearl finish (Wipeable grade) ( Min. 1.1 ltr/10 sqm).

Cost of work shall be inclusive of all materials, labor etc. as per manufacturers specification and finish up to the

entire satisfaction of the Engineer in Charge.

TOTAL SUB HEAD -7 3521296.00 896504.00

Digitally signed by ANUJ

Abstract of Cost (Civil ) 24 GULIA

ABSTRACT OF COST

DETAILED ESTIMATE FOR THE CONSTRUCTION OF GRID INDIA

SH: INTERIOR WORKS

Refer RATE (DSR NON DSR AMOUNT (NON-

S.No. Office QUANTITY UNIT AMOUNT (DSR)

(DSR'23) '23) RATE DSR)

(SH: - 8.0 - ALUMINIUM & GLAZING WORK)

Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard

tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:

1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e.

at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. aluminum sections shall be smooth,

rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminum snap

beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and

the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately):

For fixed portion

Polyester powder coated aluminum (minimum thickness of polyester powder coating 50 micron).

Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard

tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:

1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e.

at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. aluminum sections shall be smooth,

rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminum snap

beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and

the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately):

For Openable portion

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision

for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings

shall be paid for separately).

Polyester powder coated aluminum (minimum thickness of polyester powder coating 50 micron).

Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with PVC/neoprene

gasket, aluminum snap beading, aluminum channel etc. complete as per the architectural drawings and the

82 21.3.3 directions of engineer-in-charge . (Cost of aluminum snap beading, channel shall be paid in basic item) 250.00 250.00 sqm 1685.40 421350.00

With float glass panes of 8 mm thickness.

Filling the gap in between aluminium/ stone/ wood/ upvc frame and adjacent RCC/ Brick/ Stone/ wood/ Ceramic/

Gypsum work by providing weather / structural non sag elastomeric PU sealant over backer rod of approved

quality as per architectural drawings and direction of Engineer-in-charge complete, complying to ASTM C920,

Upto 20 mm depth and 20 mm width

Digitally signed by ANUJ

Abstract of Cost (Civil ) 25 GULIA

ABSTRACT OF COST

DETAILED ESTIMATE FOR THE CONSTRUCTION OF GRID INDIA

SH: INTERIOR WORKS

Refer RATE (DSR NON DSR AMOUNT (NON-

S.No. Office QUANTITY UNIT AMOUNT (DSR)

(DSR'23) '23) RATE DSR)

Providing and supplying aluminum extruded tubular and other aluminum sections of approved make as per the

architectural drawings and approved shop drawings , the aluminum quality as per grade 6063 T5 or T6 as per

BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour

and shade as approved by the Engineer-in-Charge. (The item includes cost of material such as cleats, sleeves,

84 25.1 screws etc. necessary for fabrication of extruded aluminum frame work. Nothing extra shall be paid on this 7369.50 7369.50 kg 414.30 3053184.00

account). The weight of aluminium extruded section shall be taken for purpose of payment.

Designing,Providing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of

structural glazing/ Curtain wall/ Glazing (with open joints) for linear as well as curvilinear portions of the building

for all heights and all levels, including :

85 a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS

875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure),

including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminum

cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather

silicone sealants, flashings, fire stop (barrier)-cum-smoke seals, microwave cured EPDM gaskets for water

tightness, pressure equalisation & drainage and protection against fire hazard including:

b) Fabricating and supplying serrated M.S. hot dip galvanised / aluminum alloy of 6005 T5 brackets of required

sizes, sections and profiles etc. to accommodate 3 Dimentional movement for achieving perfect verticality and

fixing structural glazing system rigidly to the RCC/ masonry/structural steel framework of building structure using

stainless steel anchor fasteners/ bolts, nylon separator to prevent bimetallic contacts with nuts and washers etc.

of stainless steel grade 316, of the required capacity and in required numbers..

c) Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant

compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shop

environment , including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand

and manufacture, as per the approved sealant design, within and all around the perimeter for holding glass

d) Providing and fixing in position flashings of solid aluminum sheet 1 mm thick and of sizes, shapes and

profiles, as required as per the site conditions, to seal the gap between the building structure and all its

interfaces with curtain glazing to make it watertight.

e) Making provision for drainage of moisture/ water that enters the curtain glazing system to make it watertight,

by incorporating principles of pressure equalization, providing suitable gutter profiles at bottom (if required),

making necessary holes of required sizes and of required numbers etc. complete. This item includes cost of all

inputs of designing, labour for fabricating and installation of aluminum grid, installation of glazed units, T&P,

scaffolding and other incidental charges including wastages etc., enabling temporary structures and services,

cranes or cradles etc. as described above and as specified. The item includes the cost of getting all the

structural and functional design including shop drawings checked by a structural designer, dully approved by

Engineer-in-charge.

Digitally signed by ANUJ

Abstract of Cost (Civil ) 26 GULIA

ABSTRACT OF COST

DETAILED ESTIMATE FOR THE CONSTRUCTION OF GRID INDIA

SH: INTERIOR WORKS

Refer RATE (DSR NON DSR AMOUNT (NON-

S.No. Office QUANTITY UNIT AMOUNT (DSR)

(DSR'23) '23) RATE DSR)

Note:- 1. The cost of providing extruded aluminum frames, shadow boxes, extruded aluminum section capping

for fixing in the grooves of the curtain glazing and vermin proof stainless steel wire mesh shall be paid for

separately under relevant items under this subhead. However, for the purpose of payment, only the actual area

of structural glazing (including width of grooves ) on the external face shall be measured in sqm. up to two

decimal places.

Note:-2. The following performance test are to be conducted on structural glazing system if area of structural

glazing exceeds 2500 Sqm from the certified laboratories accredited by NABL(National Accreditation Board for

Testing and Calibration Laboratories),Department of Science & Technologies, India. Cost of testing is payable

The NIT approving authority will decide the necessity of testing on the basis of cost of the work, cost of the test

and importance of the work. Performance Testing of Structural glazing system Tests to be conducted in the

NABL accredited lab or by any other accreditation body which operates in accordance with ISO /IEC 17011 and

accredits labs as per ISO/ IEC 17025.

1. Performance Laboratory Test for Air Leakage Test (-50pa to –300pa) & (+50pa to +300pa) as per ASTM E-

283-04 testing method for a range of testing limit 1 to 200 mVhr”.

2. Static Water Penetration Test. (50pa to 1500pa) as per ASTME- 331-09 testing method for a range up to 2000

3. Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01- 05 testing method for a range upto 2000

4. Structural Performance Deflection and deformation by static air pressure test (1.5 times design wind pressure

without any failure) as per ASTME-330-10 testing method for a range upto 50 mm”

5. Seismic Movement Test (upto 30 mm) as per AAMA 501.4-09 testing method for Qualitative test” Tests to be

conducted on site

6. Onsite Test for Water Leakage for a pressure range 50 kPa to 240 kPa (35psi) upto 2000ml”

Digitally signed by ANUJ

Abstract of Cost (Civil ) 27 GULIA

ABSTRACT OF COST

DETAILED ESTIMATE FOR THE CONSTRUCTION OF GRID INDIA

SH: INTERIOR WORKS

Refer RATE (DSR NON DSR AMOUNT (NON-

S.No. Office QUANTITY UNIT AMOUNT (DSR)

(DSR'23) '23) RATE DSR)

Designing,Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed

28mm thick D.G.U. consisting of outer high performance 6mm thickheat strengthen (HS)/ toughened glass +

16mm air gap with argon + Inner 6mm glass heat strengthen (HS)/ toughened glass insulated glass (double

glazed) vision panel units of size and shape as required and specified, comprising of an outer 6mm thick

heatstrengthen high performance glass , of approved colour and shade with reflective soft / hard coating on

surface # 2 , spacer tube 16mm wide, Inner 6mm glass heat strenghten ( HS), dessicants, including primary

seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the

Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-

Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor.“(Payment for fixing of

IGU Panels in the curtain glazing is included in cost of relevant item )“For payment, only the actual area of glass

86 MR on face # 1 of the glass panels (including the areas of the grooves and weather silicone sealant)provided and 867.00 867.00 sqm 5431.00 4708677.00

fixed in position, shall be measured in sqm.“.

(i)Glass type A - 28mm thick D.G.U. consisting of outer high performance 6mm thick heat strengthen (HS)/

toughened glass + 16mm air gap with argon gas + Inner 6mm heat strenghten ( HS)/ toughened clear glass

(properties shall visible Light transmittance (VLT) of minimum 45%, Light reflection internal 10 to 20%, light

reflection external 10 to 20 %, SHGC less than or equal to 0.25 and U value of less than 1.10 W/m2 degree K

Providing and fixing of façade at all heights with extruded hollow Clay / Terracotta as per approved make

ventilated rainscreen tiles of height 300/ 400mm and length of 1190/1200 mm of approved texture,design and

pattern having Flexural Strength/ Modulus of Rupture of ? 14 N/m² and maximum water absorption of 10%

tested as per ISO 10545-4:2004(E) and ISO 10545-3:1995 respectively in true level fixed to a supporting

aluminium framework (Alloy 6063 T5/T6) consisting of vertical 'T' (for intermediates)/ 'L' (for ends/ termination)/

Tubular sections (at corners)of size 80x60x2mm/ 40x60x2mm/ 40x40x2mm respectively, spaced at maximum

87 spacing of 1200mm c/c matching to the tile vertical grid, and horizontal aluminium 'C'-clamps of size 56x34x2mm

thickness of length 150mm at junction of tiles and of length 75mm at wall ends/ corners fixed on top of the

vertical sections at spacing of 250/ 300/ 400mm c/c matching to the tile horizontal grid with two numbers of self-

drilling / self-tapping SS screws of size 5.5x25 mm with EPDM washers.

Digitally signed by ANUJ

Abstract of Cost (Civil ) 28 GULIA

ABSTRACT OF COST

DETAILED ESTIMATE FOR THE CONSTRUCTION OF GRID INDIA

SH: INTERIOR WORKS

Refer RATE (DSR NON DSR AMOUNT (NON-

S.No. Office QUANTITY UNIT AMOUNT (DSR)

(DSR'23) '23) RATE DSR)

The vertical 'T'/'L/ Tubular' sections shall be fixed to the wall using HDG (hot-dip-galvanized) steel Lbrackets

(galvanizing thickness of minimum 80 microns) of size 110x80x6 mm at intermediate vertical aluminium profiles

and of size 220x110x12 mmat outer corners and stainless steel grade 304,M10 full threaded anchor fasteners

with nylon sleeve 100mm long (for brick work) and M8 expansion anchor fasteners 75mm long for concrete

surface, spacing of brackets to be based on a structural/ static calculation. The brackets shall be of length

175mm at junction of two vertical aluminium profiles and of length 100mm at intermediate points of vertical

profiles and shall be fixed to the vertical aluminium T / L / Tubular profiles using two numbers self-drilling/ self-

tapping SS screws of size 5.5x25 mm with EPDM washers.“EPDM gaskets to be fixed in between brackets and

vertical profiles. The tiles shall be mounted on the ‘C’ clamps such that the tiles are supported at top and bottom

at both ends. The tiles shall be mounted on the Cclamps with EPDM profiles in between such that the tiles are

supported at top and bottom at both ends. The vertical joint open groove between two adjacent tiles shall be

The tiles and system shall be designed to resist wind load as per IS 875 (Part 3) according to different zones.

The tiles shall be installed using the ventilated rain screen principle with provision for natural ventilation of the

space between the façade tiles and the structural wall. The work shall be carried out as per specification,

drawing and as per direction of the Engineer-in-Charge. Note: Scaffolding wherever required to be paid

With 18-24mm thickness (+/- 10%) terracotta tiles of grey colour or as approved colour

Digitally signed by ANUJ

Abstract of Cost (Civil ) 29 GULIA

ABSTRACT OF COST

DETAILED ESTIMATE FOR THE CONSTRUCTION OF GRID INDIA

SH: INTERIOR WORKS

Refer RATE (DSR NON DSR AMOUNT (NON-

S.No. Office QUANTITY UNIT AMOUNT (DSR)

(DSR'23) '23) RATE DSR)

Providing, fabricating, testing, installing and fixing in position Curtain Wall with aluminum Composite Panel

Cladding / ceiling,as per approved make- with open grooves for linear as well as curvilinear portions of the

building , for all heights and all levels etc. including:

Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle

as required, proper drainage of water to make it watertight including checking of all the structural and functional

Providing, fabricating and supply and fixing panel of aluminum composite panel cladding in pan shape in metallic

colour of approved shades made out of (5XXX series, H-24 BARE aluminum coil temper) - 4mm thick aluminum

composite panel (0.5mm+3mm+0.5mm) material consisting of 3mm thick FR(AlMg1) grade mineral core(70%

non combustible Mineral filled and 30% virgin polymer) sandwiched between panel cladding sheet shall be coil

coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin (Minimum70% of resin) coating of

approved colour and shade on face # 1( Pencil hardness EN 13523-2 is HB-F) and polymer (Service) coating on

face # 2 as specified. The peel of strength of ACP should be 150Nmm/mm . Stainless steel screws, nuts, bolts,

washers, cleats, weather silicone sealant, backer rods etc. “weather silicone sealant, backer rods etc.

88 8.32 The fastening brackets of aluminum alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated 300.00 300.00 sqm 5015.05 1504515.00

washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS

316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and

drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all

samples of the individual components for testing in an approved laboratory, field tests on the assembled working

curtain wall with aluminum composite panel cladding, cleaning and protection of the curtain wall with aluminum

composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding

is payable under the relevant aluminum items The Contractor shall provide curtain wall with aluminum composite

panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per

item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge.

However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum

Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places."

Providing and fixing stainless steel ( Grade 316) railing ,fender,bollords, gate, door or any other item made of

Hollow tubes, channels, angle ,plates etc.as per approved make- including , grinding, buffing, polishing and

making curvature (wherever required) , making necessary arrangement for fixing of glass of 13.52 thickness

and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary

accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or

the side of waist slab with suitable arrangement as per drawings and approval of Engineer-in-charge, (for

payment purpose only weight of stainless steel members ( lowest of actual and standard weight) shall be

89 MR considered etc.), (Note : (i) Please note that no site welding of SS pipes will be allowed and longitudinal joints 2000.00 2000.00 Kg 924.00 1848000.00

shall be made by arrangement of internal SS sleeves, in vertical pipes no joints are permitted) (ii) Rate includes

preparation and submission of shop drawings by contractor. work shall be executed on the basis of approved

shop drawings, nothing extra shall be payable for shop drawings. (iv) ( One sample of each section shall be

tested for every 5000 kg or part thereof for confirmation to SS grade 304 ).

Digitally signed by ANUJ

Abstract of Cost (Civil ) 30 GULIA

ABSTRACT OF COST

DETAILED ESTIMATE FOR THE CONSTRUCTION OF GRID INDIA

SH: INTERIOR WORKS

Refer RATE (DSR NON DSR AMOUNT (NON-

S.No. Office QUANTITY UNIT AMOUNT (DSR)

(DSR'23) '23) RATE DSR)

Fabrication, supply & installation of Floor mounted SS-316 grade glass railing made up of 50mm dia top rail

mounted on SS soild flat baluster of 54x12mm width to hold the top rail, Height of the railing shall be 1200 mm

from the floor to the top of the top rail,The baluster shall have infill of 10.89mm thick ( 5+0.89 SGP+5) laminated

Toughened glass with height of 800mm high and length as per the layout plan connected to the baluster with

SS 304 grade Glass holders.The balusters shall be mounted on the floor with SS Grade 316 base plate of 100x

90 MR 100mm x 8mm thick fixed on the floor with 4 No. M-8 grade GI threaded chemically grouted SS-316 grade 100.00 100.00 sqm 18050.00 1805000.00

fasteners.The work shall be done upto the satisfaction of the Engineer-in-Charge. (Please note that no welding

of SS pipes will be allowed and work shall be done by a specialized agency on modular and component basis).

Providing & Fixing Frosted Translucent, cast PVC, self-adhesive vinyl, special CRYSTAL-effect film to

reproduce Sand-blasting effect on glass with customised designs, thickness of 2 mil (0.05mm) without adhesive

& 2.5 -3mil (0.8)with adhesive having minimum tensile strength of 2.9-3.5 pound/inch at 71F/73 F(0.6 kg/cm at

91 MR 23 C). Adhesion after 24-36hrs of installation should be 4 pounds/inch (0.7 kg/cm) on Acrylic, Glass 350.00 350.00 sqm 3024.65 1058628.00

Polycarbonate: Product performance/MCS warranty of 3yrs (if exposed to direct sunlight) to 10 yrs-15yrs

(indoors) must be endorsed by the manufacturer.

Providing and fixing stainless steel ( grade 304 ) floor stop half dome with 45mm dia with all necessary

92 MR accessories , screws etc in satin chrome of dorma or equivalent make. 12.00 12.00 Each 482.10 5785.00

Digitally signed by ANUJ

Abstract of Cost (Civil ) 31 GULIA

ABSTRACT OF COST

DETAILED ESTIMATE FOR THE CONSTRUCTION OF GRID INDIA

SH: INTERIOR WORKS

Refer RATE (DSR NON DSR AMOUNT (NON-

S.No. Office QUANTITY UNIT AMOUNT (DSR)

(DSR'23) '23) RATE DSR)

(SH: -9.0 - WATER PROOFING)

Note : All water proofing work ,Contractor shall give 10 years guarantee for water proofings.

Waterproofing Application for sunken portion of WCs, bathroom,kitchen, balc etc etc

Providing and laying water proofing treatment in sunken portion of WCs,kitchen, bathroom, balc etc.and like aea

consisting of applying :

a) Making the surface free of all thedepression / undulations, dust dirt, laitance and all the adhesion inhibiting

material and making surface even by removing undulation on the entire surface by treating / filling with high

strength polymer for reparing and getting surface leveled.

b) Teating joints of wall and slab and around pipe junction of wall / floor with Velosit DB 830 joint tap or

equivalent as approved 200mm wide fixed in place with VELOSIT WP 124 Applyiing Ist coat of waterproofing

slurry on the wall -slab joint and immediately placing the tap over it and press it into the still wet slurry with steel

trowel to enxure adhesion and release and trapped air , Remaining area/ water outles to be treated in the same

93 MR c) After the entire surface preparation has been done, prewetting of the entire concrete surface and providing 396.67 396.67 sqm 925.00 366920.00

and application of the Ist coat of Velosit WP or equivalent as approved with a masons brush.After the Ist coat

has sufficently dried the 2nd coat of Velosit WP cna be approed . The total consumption of the product should

not less than 2.5kg / sqm in 2 coats.

d) After completion of the above said application , the waterproofed coating should be left to air cure for

minimum of 48 hours . Care should be taken that during this curing period walking or any other activities should

be avoided on it.

a) Surface area treated with Velosit wp 124 or equivalent as approved complete applying @ 2.5kg / sqm

Digitally signed by ANUJ

Abstract of Cost (Civil ) 32 GULIA

ABSTRACT OF COST

DETAILED ESTIMATE FOR THE CONSTRUCTION OF GRID INDIA

SH: INTERIOR WORKS

Refer RATE (DSR NON DSR AMOUNT (NON-

S.No. Office QUANTITY UNIT AMOUNT (DSR)

(DSR'23) '23) RATE DSR)

Waterproofing Application for sunken portion of WCs, bathroom,kitchen, balc etc etc

Providing and laying water proofing treatment in sunken portion of WCs,kitchen, bathroom, balc etc.and like aea

consisting of applying :

a) Making the surface free of all thedepression / undulations, dust dirt, laitance and all the adhesion inhibiting

material and making surface even by removing undulation on the entire surface by treating / filling with high

strength polymer for reparing and getting surface leveled.

b) Teating joints of wall and slab and around pipe junction of wall / floor with Velosit DB 830 joint tap or

equivalent as approved 200mm wide fixed in place with VELOSIT WP 124 Applyiing Ist coat of waterproofing

slurry on the wall -slab joint and immediately placing the tap over it and press it into the still wet slurry with steel

trowel to enxure adhesion and release and trapped air , Remaining area/ water outles to be treated in the same

94 MR c) After the entire surface preparation has been done, prewetting of the entire concrete surface and providing 100.00 100.00 sqm 827.00 82700.00

and application of the Ist coat of Velosit WP or equivalent as approved with a masons brush.After the Ist coat

has sufficently dried the 2nd coat of Velosit WP cna be approed . The total consumption of the product should

not less than 2.5kg / sqm in 2 coats.

d) After completion of the above said application , the waterproofed coating should be left to air cure for

minimum of 48 hours . Care should be taken that during this curing period walking or any other activities should

be avoided on it.

b) Joint Treatment with TAPE -VELOSIT DB 830 or equivalent as approved , 200 wide tap

TOTAL SUB HEAD -9 0.00 449620.00

Digitally signed by ANUJ

Abstract of Cost (Civil ) 33 GULIA

ABSTRACT OF COST

DETAILED ESTIMATE FOR THE CONSTRUCTION OF GRID INDIA

SH: INTERIOR WORKS

Refer RATE (DSR NON DSR AMOUNT (NON-

S.No. Office QUANTITY UNIT AMOUNT (DSR)

(DSR'23) '23) RATE DSR)

SUB-HEAD:10: MISCELLANEOUS WORK:-

Providing and fixing 6mm thick bevelled edge mirror of superior glass of approved quality and approved make

with VHP tap 25mm dia stainless steel stud and 10mm brush finish stainless steel trims machine cut in required

95 MR size and shape as approved shade colour etc complete at all levels as per detailed drawings and direction of 20.00 20.00 sqm 1067.00 21340.00

Engineer in Charge.

Providing and fixing counters (Reception ,Wash basin or other similar location) with 12 mm thick antibacterial

anti fungal, boiling water resistant heat resistant, impact resistant, insulative non conductive, stain resistant,

scratch resistant, Green Guard certified Acrylic solid surface of approved make (LG Himac, Dupoint, Neonnex,

Hanex or equivalent as approved) in approved colour and design, confirming to relevant standards, and having

minimum Specific Gravity 1.65 g/cm3, fixed over MS supporting structure with all mechanical fixtures as per

manufacturer's specification and guideline, including fascia and back splash area as per approved drawings and

96 MR design, including fixing of solid acrylic surface over 12 mm thick (BWP) with suitable Low VOC adhesive, 30.00 30.00 Sqm 15988.40 479652.00

moulding of edges, buffing of surface, making of holes for plumbing fixtures, flushing of joints, necessary

hardware, silicon sealants, etc. all complete as per direction of Engineer In charge. The plan and elevation area

(horizontal and vertical) excluding wash basin area will be measured for payment.

Extra over above item , for providing oval/ rectangular shaped ( Below counter / above counter) wash basin of

size 550x450 /550 x 400 mm in Wash basion counter or other similar location, made of molded surface of 12

97 MR mm thick Acrylic solid of same specification as above, and in approved color and design, all complete as per 54.00 54.00 Each 10797.35 583057.00

drawings, specification and direction of Engineer in charge.

Providing and fixing Urinal Partition of 12mm thick board both side decorative compact laminate of required

colour ,shade and sizes as manufactured of approved make including all stainless steel accessories/ fittings (

98 MR SS-304 grade) like L clamp with ss screws etc as desired. all complete as per drawing and direction of 12.00 12.00 Each 4402.00 52824.00

Engineer in charge. (size =(450x900)mm

Providing and fixing wall cladding with 12 mm thick antibacterial anti fungal, boiling water resistant heat

resistant, impact resistant, insulative non conductive, stain resistant, scratch resistant, Green Guard certified

Acrylic solid surface of approved make in approved colour and design, confirming to relevant standards, and

having minimum Specific Gravity 1.65 g/cm3, fixed with aluminum frame over wall in true line and level, as

99 MR per manufacturer's specification , drawings and design, including suitable Low VOC adhesive, buffing of 75.00 75.00 Sqm 16957.40 1271805.00

surface, making of holes for plumbing fixtures, flushing of joints, necessary hardware, silicon sealants, etc. all

complete as desired and direction of Engineer In charge. Note :-Only surface area of acrylic solid surface panel

alongwith its groove shall be measured for payment.

Digitally signed by ANUJ

Abstract of Cost (Civil ) 34 GULIA

ABSTRACT OF COST

DETAILED ESTIMATE FOR THE CONSTRUCTION OF GRID INDIA

SH: INTERIOR WORKS

Refer RATE (DSR NON DSR AMOUNT (NON-

S.No. Office QUANTITY UNIT AMOUNT (DSR)

(DSR'23) '23) RATE DSR)

Providing and fixing of 6mm thick toughned lacquered glass as per approved of approved color / shade on a

perfectly leveled on the existing wall fixed with clips (either of I/J1/J2, or equivalent as approved made of

polycarbonate, grey backing foam to accommodate substrate undulation, with a horizontal load capacity of

30Kg/100mm and vertical pullout load > 200kg/100mm). Glass should be supported with 1mm thick lip covering

upto 3mm of glass surface; clips should be fixed using durable, non-corrosive, strong screw 45mm long .

Lacquered glass must be made industrially (via curtain coating process); opaque (if viewed against a support

wall), coated with PU lacquer (minimum 50 micron thick); color consistency (measured by Minolta

spectrophotometer CM5081); highly durable (passes PERSOZ hardness test for minimum 220 oscillations);

humid resistant (conforms to BS EN 1036 1999); environmentally friendly (no lead, no arsenic, no copper, no

formaldehyde); appropriate recycled content (12% post industrial / 6% post consumer); compressive strength

100 MR (1000 MPa) & tensile strength (40 MPa),same as float glass. Contacts all complete required to perform as per 148.00 148.00 Sqm 5108.00 755984.00

specification and drawing Nothing shall be paid in this account.

The Contractor shall provide glass having all the performance characteristics all complete , as per the

Architectural drawings, as per Item description, as specified, as per the approved shop drawings and as directed

by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the

glass (including width of groove) shall be measured in sqm up to two decimal places.

Digitally signed by ANUJ

Abstract of Cost (Civil ) 35 GULIA

ABSTRACT OF COST

DETAILED ESTIMATE FOR THE CONSTRUCTION OF GRID INDIA

SH: INTERIOR WORKS

Refer RATE (DSR NON DSR AMOUNT (NON-

S.No. Office QUANTITY UNIT AMOUNT (DSR)

(DSR'23) '23) RATE DSR)

Supplying and installing roller blinds of approved make model and shade at all heights and location and required

width and comprising of approved shade and quality fabric, 1 mm thick anodized extruded Aluminium alloy roller

tube of 38-mm O.D , a bidirectional operating Clutch mechanism designed for adjustment-free, slippage-free,

crash proof smooth operation for all heights, high strength fiber glass reinforced polyester idler, powder coated

steel Insert type brackets fitted with roller tube, round bottom rail, control unit engrooved with a Ball Pitch of

minimum 6.5mm, Stainless Steel Ball Chain, and powder coated atomized steel installation brackets. The clutch

mechanism comprises of a SS beaded chain and carbon steel spring wrapped by means of a high strength fiber

glass reinforced polyester assembly to transmit motion from driving to driven members. The installation brackets

shall facilitate overhead, side or face mounting with clutch assembly on either end of the roller. Idler shall

consist of a centre shaft and outside sleeve which provide bearing surface for roller tube and rotate freely on

centre shaft for smooth and quiet operation. Bottom rail along with the fabric shall be enclosed in a suitably

created pocket and shall be of powder coated aluminium tube and closed from sides with end caps. The item

includes all fittings, accessories, brackets, screws, anchor fasteners, fabric as per approved sample and shade

all complete as per drawings, tender specifications, relevant standards and direction of Engineer in charge.

101 MR (Height of blind from top bracket to bottom tube and width from bracket to bracket shall be measured for 324.00 324.00 Sqm 2092.00 677808.00

Manual Roller Blinds

Perforated Screen Blinds

Composition- 30% Polyester (max),70% PVC on Polyester(min),

Openness factor- 3-5%(as approved)

Weight (gram/ sqm)- min 440 gm/sqm

Thickness- min 0.60 mm

Fire Classification- Class A( NFPA 101 or Class 1 (UNE EN 13773) or equivalent as per relevant standards and

Fastness to light- 6-7/8 or higher

Indoor Air Quality- GreenGuard / Eco-Codice Certified.

Manufacturer's warrantee- minimum 5 years

Supplying and installing of Seclusion Blockout fabric made up of 100% Polyester with Acrylic coated of

0.32mm(PVC free) of thickness 0.50mm ±5% and weighing 270-295gsm with openness factor of 0%

.Shrinkage % Warp<0.5 & Weft <0.5,Color fastness>5-6.Fire Classification- NFPA-701 or equivalent,

GREENGUARD certified fabric. The Roller blind system consists of 38mm OD extruded out of Aluminium alloy

6063 T6 with silver anodized to provide an everlasting finish and luster, the rotary unit shall be 36mm in OD

incorporating a clutch mechanism composed of low – flexing braided polyster cord with nylon core, Control Ball

chain shall be composed of braided nylon cord (2mm dia) with high engineering grade plastic beads of 4.5mm

diameter mounted co-axially on the cord with a pitch of 6.2mm (C-T-C) Bottom rail should be powder coated

102 MR Aluminium flat bottom rail of 290 gm to finish it from the ends it should have rail end caps. The clutch will be at 324.00 324.00 Sqm 1897.00 614628.00

the tube. The return end cap bracket shall incorporate snap spring design to facilitate easy installation and

removal for maintenance activities. The bracket shall be finished with a flush mounting cover on each side

providing an aesthetic finish. It should handle up to 5 Kgs of material. The clutch should mount flush to the face

of the bracket which minimize the light gap between the shade and the window frame. Complete as per direction

of Engineer -in –Charge.

Digitally signed by ANUJ

Abstract of Cost (Civil ) 36 GULIA

ABSTRACT OF COST

DETAILED ESTIMATE FOR THE CONSTRUCTION OF GRID INDIA

SH: INTERIOR WORKS

Refer RATE (DSR NON DSR AMOUNT (NON-

S.No. Office QUANTITY UNIT AMOUNT (DSR)

(DSR'23) '23) RATE DSR)

Extra for supplying, installing, testing and commissioning remote operated motor of approved make and model,

in each roller blind and having following minimum specification. The item includes all fittings, accessories,

brackets, screws, tube of appropriate size, anchor fasteners, making electrical connections, all complete as per

drawings, tender specifications, relevant standards and direction of Engineer in charge

Torque(Nm): Minimum 3-6

Speed(rpm): Minimum 30-32

Rated Voltage(V):230, 50 Hz

Rated Power Consumption(W):120

Rated Current(A):0.5

Running Time Before Thermal Cut Off(min): 4

Average Running Noise(dbA):52 or less

Index Protection: 31 or 44(as per manufacturer's specification)

Extra for printing as per approved design over rollar blinds as per manufacturer specifications and direction of

104 MR Engineer in charge . 324.00 324.00 sqm 1384.00 448416.00

Supplying remote control of approve make and model (for each room with motorized blinds) capable of providing

individual as well as group Control (upto 16 channels) for the motors of the roller blind mentioned in above item,

105 MR including batteries all complete, as per direction of engineer in charge. (Multi Channel Remote) 12.00 12.00 each 8271.00 99252.00

Providing and laying aluminum dust buster matting (whipping & scrapping -moisture & dirt recessed ) for main

106 MR entry as per manufacturer specifictions and direction of Engineer in charge. 20.00 20.00 Sqm 18901.00 378020.00

Core cutting in RCC slab in core cutting machine in insert upto 200mm dia pipes in toilets slabs including

107 MR finishing leak proof after insertion of pipes as per direction of Engineer-in-charge 12.00 12.00 each 1168.49 14022.00

Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index)

> 78, solar reflection >0.70 and initial emittance >0.75 on waterproof and sloped surface of terrace, laid on 20

mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4coarse sand) and grouting the joints with mix of

108 12.55 white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts 970.00 970.00 sqm 1703.95 1652832.00

complete, including providing skirting upto 150 mm height along the parapet walls in the same manner.

Digitally signed by ANUJ

Abstract of Cost (Civil ) 37 GULIA

ABSTRACT OF COST

DETAILED ESTIMATE FOR THE CONSTRUCTION OF GRID INDIA

SH: INTERIOR WORKS

Refer RATE (DSR NON DSR AMOUNT (NON-

S.No. Office QUANTITY UNIT AMOUNT (DSR)

(DSR'23) '23) RATE DSR)

Supply and Installation of Multi cell Polycarbonate Panels 16 mm thick( minimum) with 5 cells ‐ 6 walls structure

over MS Supporting structures. Panel Width shall be 900-1000mm to ensure best performance for wind uplift.

The panels shall be uniform in color with an integral Microcell core with soft light finish to give diffused light. In a

cross section, the core shall be constructed of microcells not exceeding 4mm x 4mm and shall be square/

rectangular/ or in truss bridge design commonly known as X‐Structure in appearance. Panels shall be

coextruded with UV Protection layers with thickness and concentration to filter and block more than 99% of the

UV rays (UVA and UVB) through a clear panel. The weight of the only panel shall not be less than 3250 gram

per square meter. Panel shall have U value not more than 1.9 W/m2k and UV transmission of less than 0.1%

with UV filtration test AS No.1067‐1990 or equivalent test available in India. Panel and system should have

impact and shock resistance with D1‐ 10j ‐M 50 ,300 J ‐ M 50 400 J or as per IS 6892:1998 and IS 1608: 2005.

Panel system shall have Vertical Standing Seam 15mm at both sides and snap on connector to interlock the

panels with a grip‐lock 1/2 tooth locking mechanism to ensure maximum uplift capability. Panels shall be fixed

on Purlins with special SS Expansion fastener and polycarbonate U/2 connectors. Panel system shall be sealed

with additional Tape / End caps / Aluminium U‐Profile (mill finish) at the ends. Panel should pass through

Sandbag impact test ASTM E 695‐03 or as per IS 14443-97 after 25,000 hours/should be read as minimum 500

hours of environmental exposure and Hailstone impact test ASTM E 822‐81 or as per ASTM G 155. The panel

system shall pass water penetration test ASTM E – 331 or as per equivalent test available in India. The panel to

have classification under B S1 D0 for reaction to fire as per test standard EN 13501 1:2002 or equivalent test

available in India tested by an independent, recognized testing laboratory. Panels shall have Yellowness Index

as per ASTM D‐1925; the change shall not be more than 10 points after 60 months of exposure in comparison to

The Color of the panel shall change no more than 3 units as per ASTM D2244 after 60 months of exposure in

comparison to original. The Light Transmission of panels shall not change more than 10% after exposure of 60

months in comparison to original.. Panel shall be fixed over MS structural steel/MS purlin (paid separately)

conforming to the detail technical specifications as per approved architectural drawings. Trained and factory

authorized labour with supervision to complete the entire panel installation as per drawing and direction of the

engineering in charge.

Digitally signed by ANUJ

Abstract of Cost (Civil ) 38 GULIA

ABSTRACT OF COST

DETAILED ESTIMATE FOR THE CONSTRUCTION OF GRID INDIA

SH: INTERIOR WORKS

Refer RATE (DSR NON DSR AMOUNT (NON-

S.No. Office QUANTITY UNIT AMOUNT (DSR)

(DSR'23) '23) RATE DSR)

Providing and fixing Rebaring by using various diameter 12mm to 25mm.Dia, hilti/ fisher make chemical (Re-

500) max.depth 300 mm. The main reinforcement using rebars of designated dia for column/beam/Shear

walls/Foundations at designed embedement length wherever required , including power drilling, cleaning of

holes, then rebars should be inserted in holes that should be filled with FIS EM Plus of Fischer or equivalent, a

heavy duty pure epoxy based rebarring chemical with ETA approval, DIBt, approved for diameter range from 8

mm to 40 mm reinforcement bar as per manufacturer's specification as per the direction of Engg In-charge.

Drilling of hole should be done upto provided embedment depth as per the design from manufacturer approved

110 MR by EnC, followed by cleaning with blow pump, wire brush and blow pump for 4 times, complete as per the 100.00 100.00 each 850.00 85000.00

manufacturer's methodology. The chemical shall be approved for diamond-drilled and water-filled drill holes as

well as seismic applications in performance categories C1, C2 for rebar connections. Product shall have test

certificate for 120years of service life & shall have ETA complying to EAD 332402-00-0601-v01.

Digitally signed by ANUJ

Abstract of Cost (Civil ) 39 GULIA

ABSTRACT OF COST

DETAILED ESTIMATE FOR THE CONSTRUCTION OF GRID INDIA

SH: INTERIOR WORKS

Refer RATE (DSR NON DSR AMOUNT (NON-

S.No. Office QUANTITY UNIT AMOUNT (DSR)

(DSR'23) '23) RATE DSR)

(SH: - 11.0 - DISMANTLING & DEMOLISHING

Demolishing AAC/brick work manually/ by mechanical means including stacking of serviceable material and

111 disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. 50. 50.00 cum 2060.20 103010.00 0.00

15.7.4 In Cement Mortar

15.30 Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of

unserviceable material within 50 metres lead as per direction of Engineer - in- charge. 20. 20.00 cum 3551.25 71025.00 0.00

15.23 Dismantling tile work in floors/ wall and roofs laid in cement mortar including stacking material within 50 metres

15.23.1 For thickness of tiles 10 mm to 25 mm 1 335. 1335.00 sqm 73.40 97989.00 0.00

Dismantling doors, windows, glazing and clerestory windows (steel /wood/ Aluminium) shutter including

chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :

15.12.1 of area 3 sq. metres and below 100. 100.00 Each 367.20 36720.00 0.00

TOTAL SUB HEAD -11 685807.00 0.00

Digitally signed by ANUJ

Abstract of Cost (Civil ) 40 GULIA

ABSTRUCT OF COST

SH 01: LOOSE FURNITURE

ITEM NAME Description Size Unit Qty Rate Amount Reference Image

Providing and fixing in position of customised design ref. images and shop drawing as approved Working table with

Decorative Veneer as approved ( T1 ) including drawer unit of required size:

- Table top shall be made out of 36 mm thick ( 18mm+18mm) commercial ply wood of MR grade (Make: Century

Architect Ply / Durian /Archid ply /Greenlam Club) IS 303 : 1989 .

- The side panel / vertical support shall be made out of 24mm thick commercial ply wood of MR grade shall be supporting

below the working table top and front modesty shall be made out of 18mm thick commercial plywood of MR grade having

height of 710 mm shall be fixed at front side of table top.

- Table top, both sides of vertical support/ side panel and both sides of modesty shall be pasted with 3.50 to 4.00 mm

thick natural veneer (Make : Archid ply/ Durian/ Century/ Duro) with hot pressed glue/ adhesive of approved quality.

- Balancing Laminate pasted below the table top shall be thickness of 0.60 mm in gloss / matt finish with high density

protective surface layer pasted with hot pressed glue/ adhesive of approved quality.

- The working or non-working edges shall be provided with veneer edge binding using with special hot melt glue at hot

- All necessary hardware/ fitting/S.S. hinges etc. of approved quality (Make: Ebco/Hettich/Hafele/Sumsung Irex).

- Natural Veneer to be use is Steam Beach/ English walnut or similar price as approved shade/ colour.

- All veneered to be sprayed with 03 coats of PU polish finished in desired shade using base material of

MRF/Jeevanjor/Sirca.

- Agency has to be adopt sound Interior Design practice while fabrication for stability and asthetically.

- The commercial ply wood/veneer/laminate shall be make of (Greenlam club/Century Architect ply /Durian/Archid ply) IS

- Wooden moulding require at skirting level to be covered both the sides panels and front modesty.

- Table shall have adequate provisions for the movement of electric/ data cables at desired levels. Keyboard runs on

telescopic channel for smooth operation

- For installation of table wooden dowels and minifix to use for additional support.

- Any additional member are support required for stability shall be provided where ever required as per instruction of

-All CRCA steel components / parts powder coated of 50-60 micron. All necessary hardware/ fitting/ hinges/ tower bolts/

handles etc . of approved quality (Make: Ebco/Hettich/Kitch).

- All Complete job as desired with appproved SS Hardwares ( grade 316 ) and as per direction and satisfaction of

Engineer -in –Charge.

a) (Main Table ( Front )

b) Side Unit with Decorative Veneer as approved with 2 nos file drawer and 1 no box drawer

c) Storage/ Filing / Back unit (L)3000x (W)450x

Providing and fixing in position of customised design ref. images and shop drawing as approved Working table with

Decorative Veneer as approved ( T2 ) including drawer unit of required size:

- Table top shall be made out of 36 mm thick ( 18mm+18mm) commercial ply wood of MR grade(Make: Century Architect

Ply / Durian /Archid ply /Greenlam Club) IS 303 : 1989 .

- The side panel / vertical support shall be made out of 24mm thick commercial ply wood of MR grade shall be supporting

below the working table top and front modesty shall be made out of 18mm thick commercial plywood of MR grade having

height of 710 mm shall be fixed at front side of table top.

- Table top, both sides of vertical support/ side panel and both sides of modesty shall be pasted with 3.50 to 4.00 mm

thick natural veneer (Make : Archid ply/ Durian/ Century/ Duro) with hot pressed glue/ adhesive of approved quality.

- Balancing Laminate pasted below the table top shall be thickness of 0.60 mm in gloss / matt finish with high density

protective surface layer pasted with hot pressed glue/ adhesive of approved quality.

- The working or non-working edges shall be provided with veneer edge binding using with special hot melt glue at hot

- All necessary hardware/ fitting/S.S. hinges etc. of approved quality (Make: Ebco/Hettich/Hafele/Sumsung Irex).

- Natural Veneer to be use is Steam Beach/ English walnut or similar price as approved shade/ colour.

- All veneered to be sprayed with 03 coats of PU polish finished in desired shade using base material of

MRF/Jeevanjor/Sirca.

- Agency has to be adopt sound Interior Design practice while fabrication for stability and asthetically.

- The commercial ply wood/veneer/laminate shall be make of (Greenlam club/Century Architect ply /Durian/Sumo/Archid

- Wooden moulding require at skirting level to be covered both the sides panels and front modesty.

- Table shall have adequate provisions for the movement of electric/ data cables at desired levels. Keyboard runs on

telescopic channel for smooth operation

- For installation of table wooden dowels and minifix to use for additional support.

- Any additional member are support required for stability shall be provided where ever required as per instruction of

-All CRCA steel components / parts powder coated of 50-60 micron. All necessary hardware/ fitting/ hinges/ tower bolts/

handles etc. of approved quality (Make: Ebco/Hettich/Kitch).

- All Complete job as desired with appproved SS Hardwares ( grade 316 ) and as per direction and satisfaction of

Engineer -in –Charge.

a) (Main Table ( Front )

Side Unit with Decorative Veneer as approved with 2 nos file drawer and 1 no box drawer

b) (L)2400x (W)600x (H)650 Digitally5 signed1,10,891.00

Storage/ Filing / Back unit

Providing and fixing in position of customised design ref. images and shop drawing as approved Working table with

Decorative Veneer as approved ( T3 ) including drawer unit of required size:

- Table top shall be made out of 36 mm thick ( 18mm+18mm) commercial ply wood of MR grade(Make: Century Architect

Ply / Durian /Archid ply /Greenlam Club) IS 303 : 1989 .

- The side panel / vertical support shall be made out of 24mm thick commercial ply wood of MR grade shall be supporting

below the working table top and front modesty shall be made out of 18mm thick commercial plywood of MR grade having

height of 710 mm shall be fixed at front side of table top.

- Table top, both sides of vertical support/ side panel and both sides of modesty shall be pasted with 3.50 to 4.00 mm

thick natural veneer (Make : Archid ply/ Durian/ Century/ Duro) with hot pressed glue/ adhesive of approved quality.

- Balancing Laminate pasted below the table top shall be thickness of 0.60 mm in gloss / matt finish with high density

protective surface layer pasted with hot pressed glue/ adhesive of approved quality.

- The working or non-working edges shall be provided with veneer edge binding using with special hot melt glue at hot

- All necessary hardware/ fitting/S.S. hinges etc. of approved quality (Make: Ebco/Hettich/Hafele/Sumsung Irex).

- Natural Veneer to be use is Steam Beach/ English walnut or similar price as approved shade/ colour.

- All veneered to be sprayed with 03 coats of PU polish finished in desired shade using base material of

MRF/Jeevanjor/Sirca.

- Agency has to be adopt sound Interior Design practice while fabrication for stability and asthetically.

- The commercial ply wood/veneer/laminate shall be make of (Greenlam club/Century Architect ply /Durian/Sumo/Archid

- Wooden moulding require at skirting level to be covered both the sides panels and front modesty.

- Table shall have adequate provisions for the movement of electric/ data cables at desired levels. Keyboard runs on

telescopic channel for smooth operation

- For installation of table wooden dowels and minifix to use for additional support.

- Any additional member are support required for stability shall be provided where ever required as per instruction of

-All CRCA steel components / parts powder coated of 50-60 micron. All necessary hardware/ fitting/ hinges/ tower bolts/

handles etc. of approved quality (Make: Ebco/Hettich/Kitch).

- All Complete job as desired with appproved SS Hardwares ( grade 316 ) and as per direction and satisfaction of

Engineer -in –Charge.

a) (Main Table ( Front )

Side Unit with Decorative Veneer as approved with 2 nos file drawer and 1 no box drawer

Storage/ Filing / Back unit

Providing and fixing in position of customised design ref. images and shop drawing as approved Working table with

Decorative Veneer as approved ( T4 ) including drawer unit of required size:

- Table top shall be made out of 36 mm thick ( 18mm+18mm) commercial ply wood of MR grade(Make: Sumo / Century

Architect Ply / Durian /Archid ply /Greenlam Club) IS 303 : 1989 .

- The side panel / vertical support shall be made out of 24mm thick commercial ply wood of MR grade shall be supporting

below the working table top and front modesty shall be made out of 18mm thick commercial plywood of MR grade having

height of 710 mm shall be fixed at front side of table top.

- Table top, both sides of vertical support/ side panel and both sides of modesty shall be pasted with 3.50 to 4.00 mm

thick natural veneer (Make : Archid ply/ Durian/ Century/ Duro) with hot pressed glue/ adhesive of approved quality.

- Balancing Laminate pasted below the table top shall be thickness of 0.60 mm in gloss / matt finish with high density

protective surface layer pasted with hot pressed glue/ adhesive of approved quality.

- The working or non-working edges shall be provided with veneer edge binding using with special hot melt glue at hot

- All necessary hardware/ fitting/S.S. hinges etc. of approved quality (Make: Ebco/Hettich/Hafele/Sumsung Irex).

- Natural Veneer to be use is Steam Beach/ English walnut or similar price as approved shade/ colour.

- All veneered to be sprayed with 03 coats of PU polish finished in desired shade using base material of

MRF/Jeevanjor/Sirca.

- Agency has to be adopt sound Interior Design practice while fabrication for stability and asthetically.

- The commercial ply wood/veneer/laminate shall be make of (Greenlam club/Century Architect ply /Durian/Sumo/Archid

- Wooden moulding require at skirting level to be covered both the sides panels and front modesty.

- Table shall have adequate provisions for the movement of electric/ data cables at desired levels. Keyboard runs on

telescopic channel for smooth operation

- For installation of table wooden dowels and minifix to use for additional support.

- Any additional member are support required for stability shall be provided where ever required as per instruction of

-All CRCA steel components / parts powder coated of 50-60 micron. All necessary hardware/ fitting/ hinges/ tower bolts/

handles etc. of approved quality (Make: Ebco/Hettich/Kitch).

- All Complete job as desired with appproved SS Hardwares ( grade 316 ) and as per direction and satisfaction of

Engineer -in –Charge.

a) (Main Table ( Front )

Side Unit with Decorative Veneer as approved with 2 nos file drawer and 1 no box drawer

Digitally signed by ANUJ

Providing and fixing in position of customised design ref. images and shop drawing as approved Working table with

decorative laminate as approved ( T5 ) including drawer unit of required size:

- Table top shall be made out of 36mm thick commercial ply wood of MR grade (Make: Sumo Architect Ply /Durian

/Archid ply/Greenlam Club) IS 303 : 1989 on both side of approved color and contained the thickness shall be 36mm

(12mm Plywood + 12mm baton between both the plywood + 12mm Plywood). For additional strength wooden framing

should be provided between both the plywood of table top total 06 numbers vertical baton size 12mm x 25mm x 900

height and 04 numbers horizontal baton 12mm x 25mm x 2100 length to be used.

- The side panel / vertical support shall be made out of 25mm thick commercial ply of MR grade (Make: Sumo /Century

Architect Ply /Durian /Archid ply /Greenlam Club) IS 303 : 1989 shall be supporting below the working table top and

front modesty shall be made out of 18mm thick commercial ply of MR grade (Make: Sumo /Century Architect Ply

/Durian /Archid ply /Greenlam Club) IS 303 : 1989 having height of 650 mm to 700 mm shall be fixed at front side of

- Table top surface, both sides of vertical support/ side panel and both sides of modesty shall be pasted with 1.00 mm

5 E7 thick decorative / coloured high pressure laminated sheet (Make: Cedar Lam /Durian /Archid ply /IPL /Royal Touch)

with hot pressed glue including cost of glue/ adhesive of approved quality.

- Balancing Laminate pasted below the table top shall be thickness of 0.60 mm in gloss / matt finish with high density

protective surface layer pasted with hot pressed glue including cost of glue/ adhesive of approved quality.

- The working or non-working edges shall be provided with matching machine pressed 2mm thick PVC edging using

with special hot melt glue at hot temperature. All necessary hardware/ fitting etc. of approved quality (Make:

Ebco/Hettich/Kitch/Sumsung Irex).

- Provision for metallic Keyboard runs on telescopic channel for smooth operation.

- Table shall have adequate provisions for the movement of electric/ data cables at desired levels.

- For installation of table wooden dowels and minifix to use for additional support.

-All CRCA steel components / parts powder coated of 50-60 micron. All necessary hardware/ fitting/ hinges/ tower

bolts/ handles etc. of approved quality (Make: Ebco/Hettich/Kitch).

- All Complete job as desired with appproved SS Hardwares ( grade 316 ) and as per direction and satisfaction of

Engineer -in –Charge.

(Main Table ( Front )

Side Unit with Decorative laminate as approved with 2 nos file drawer and 1 no box drawer

Providing and fixing in position of customised design ref. images and shop drawing as approveds Sliding Tile Base

Workstation ( T-6) including drawer unit as per sizes:

- Free standing partition height 1200mm and should be minimum of 55mm thick. Partition inner frame is 1.1mm thick

mild steel. Horizontal and vertical trims are made out of extruded aluminium of 1.0mm thick.

- All Panels/trims shall be powder coated with 50 microns. Aluminium trims are elegantly fixed with special fixtures in the

partition. The framework shall be fitted with 9mm thick pre laminated Particle tiles of approved shade.

- Partition shall have provision for pin up board with fabric/ white marker/ laminated of approved shade.

- Partition framework shall have adequate provisions for the movement of electric data cables at desired 2 levels; one at

skirting and another above / below the table top. Panel have cut-outs of required sizes for installing electric switch boards

( switch samples provided by client) there will be separate slots for passage of data and electrical wires. The frames

designed to easily handle CAT6 wire at entry points. The complete partitioning work shall be carried out as per the

approved drawing.

- Balancing Laminate pasted on below the top shall be thickness of 0.60mm in gloss / matt finish with high density

protective surface layer pasted with hot pressed glue including cost of glue/ adhesive of approved quality.

6 - Table top for workstation shall be made up of 25mm thick commercial ply of MR grade (Make: Sumo /Century Architect

E6 Ply /Durian /Archid ply /Greenlam Club) IS 303 : 1989 including with 1mm thick decorative / coloured high pressure

laminated sheet (Make: Cedar Lam /Durian /Archid ply/Archid / IPL /Royal Touch) with hot pressed glue including cost of

glue/ adhesive of approved quality.

- Side panel shall be made out of 18/19mm thick commercial ply of MR grade (Make: Sumo/Century Architect Ply /Durian

/Archid /Greenlam Club) IS 303 : 1989 including with 1mm thick laminate (Make: Cedar Lam /Durian /Archid ply /IPL

Archid/ Royal Touch) IS 2046 : 1995 on both side matching with tabletop and contained the thickness shall be 18/19mm.

- The working or non-working edges shall be provided with matching machine pressed 2mm thick PVC edging using with

special hot melt glue at hot temperature. Metal Keyboard with telescopic channel for smooth operation.

- Metal CPU trolley with lockable castors for smooth operation on floor.

-All CRCA steel components / parts powder coated of 50-60 micron. All necessary hardware/ fitting/ hinges/ tower bolts/

handles etc. of approved quality (Make: Ebco/Hettich/Kitch).

- All Complete job as desired and direction of Engineer -in –Charge.

Digitally signed by ANUJ

Providing and fixing in position of customised design ref. images and shop drawing as approved, Reception counter /

table ( T115 ) as per given sizes:

- Reception counter / table shall be made out of 36mm thick commercial ply wood of MR grade (Make:Century

Architect Ply /Durian /Archid classic /Greenlam Club) IS 303 : 1989 on both side of approved color and contained the

thickness shall be 36mm (12mm Plywood + 12mm baton between both the plywood + 12mm Plywood) and cladded

with solid acrylic surface and PU /melamine polished veneer facia paste on marine ply and trim light below as per

design. Two drawers with lock and space for two pc, keyboard tray and CPU trolley will be provided. Space for

biometric and printer. Keyboard tray made of powder coated CRCA steel sheet with soft closing channels. CPU trolley

made of powder coated CRCA steel sheet with castor for smooth operation on floor. Complete table having knock

down system. Drawing unit pedestal having a combination of two drawers and one filling/ backing/ drawers bottom

/top shall be made of 18 mm thick marine ply with laminated and required size is (L)600 X (W)600 X (H)600 . For

additional strength wooden framing should be provided between both the plywood of table top total 05 numbers

vertical baton size 12mm x 25mm x 1050 height and 03 numbers horizontal baton 12mm x 25mm x 3000mm length to

7 MR - Carcase box/ under structure should be made of minimum 18/19 mm thick commercial ply wood of MR grade (Make:

Sumo/Century Architect Ply /Durian /Archid ply /Archid classic /Greenlam Club) IS 303 : 1989 modesty having height

of 650 mm to 700 mm shall be fixed at front side of table top. In the addition table height to be raised till 1050mm (H)x

300mm(D)x 3000(L)front side only.

-All Visible sides, top and edging will be cladded with 12mm thick solid acrylic surface milkey finished or as approved

colour / shade and as per detail drawing.

- Table having provision of two numbers pedestal with a combination of two drawers and One filling shall be made of

18 mm thick commercial ply of MR grade (Make: Sumo/Century Architect Ply /Durian /Archid ply /Archid/ Greenlam

Club) IS 303 : 1989 and pedestal backing/ drawers bottom shall be 8 mm thick ply of MR grade IS 303 : 1989.

- Balancing Laminate pasted below the table top, inner side of modesty/ both the side panel and pedestal inner/ outer

shall be thickness of 0.60 mm in gloss / matt finish with high density protective surface layer pasted with hot pressed

glue / adhesive of approved quality.

- The pedestal edges shall be provided with matching machine pressed 2mm thick PVC edging using with special hot

melt glue at hot temperature. All necessary hardware/ fitting etc. of approved quality (Make: Ebco/Hettich/Kitch).

- All CRCA steel components / parts powder coated of 50-60 micron. All necessary hardware/ fitting/ hinges/ tower

bolts/ handles etc. of approved quality (Make: Ebco/Hettich/Kitch).

Reception counter / table ( T15 ) (L)3000x(W)750x

b) Storage/ Filing / Back unit ( S15a)

Providing and fixing in position of customised design ref. images and shop drawing as approved,Curve Reception

counter / table ( T116 ) as per given sizes:

- Reception counter / table shall be made out of 36mm thick commercial ply wood of MR grade (Make:Century

Architect Ply /Durian /Archid classic /Greenlam Club) IS 303 : 1989 on both side of approved color and contained the

thickness shall be 36mm (12mm Plywood + 12mm baton between both the plywood + 12mm Plywood) and cladded

with solid acrylic surface and PU /melamine polished veneer facia paste on marine ply and trim light below as per

design. Two drawers with lock and space for two pc, keyboard tray and CPU trolley will be provided. Space for

biometric and printer. Keyboard tray made of powder coated CRCA steel sheet with soft closing channels. CPU trolley

made of powder coated CRCA steel sheet with castor for smooth operation on floor. Complete table having knock

down system. Drawing unit pedestal having a combination of two drawers and one filling/ backing/ drawers bottom

/top shall be made of 18 mm thick marine ply with laminated and required size is (L)600 X (W)600 X (H)600 . For

additional strength wooden framing should be provided between both the plywood of table top total 05 numbers

vertical baton size 12mm x 25mm x 1050 height and 03 numbers horizontal baton 12mm x 25mm x 3600mm Curve

length to be used.

8 MR - Carcase box/ under structure should be made of minimum 18/19 mm thick commercial ply wood of MR grade (Make:

Sumo/Century Architect Ply /Durian /Archid ply /Archid classic /Greenlam Club) IS 303 : 1989 modesty having height

of 650 mm to 700 mm shall be fixed at front side of table top. In the addition table height to be raised till 1050mm (H)x

300mm(D)x 3600(Curve length)front side only.

-All Visible sides, top and edging will be cladded with 12mm thick solid acrylic surface milkey finished or as approved

colour / shade and as per detail drawing.

- Table having provision of two numbers pedestal with a combination of two drawers and One filling shall be made of

18 mm thick commercial ply of MR grade (Make: Sumo/Century Architect Ply /Durian /Archid ply /Archid/ Greenlam

Club) IS 303 : 1989 and pedestal backing/ drawers bottom shall be 8 mm thick ply of MR grade IS 303 : 1989.

- Balancing Laminate pasted below the table top, inner side of modesty/ both the side panel and pedestal inner/ outer

shall be thickness of 0.60 mm in gloss / matt finish with high density protective surface layer pasted with hot pressed

glue / adhesive of approved quality.

- The pedestal edges shall be provided with matching machine pressed 2mm thick PVC edging using with special hot

melt glue at hot temperature. All necessary hardware/ fitting etc. of approved quality (Make: Ebco/Hettich/Kitch).

- All CRCA steel components / parts powder coated of 50-60 micron. All necessary hardware/ fitting/ hinges/ tower

bolts/ handles etc. of approved quality (Make: Ebco/Hettich/Kitch).

Reception counter / table ( T16 ) (L)3600x(W750x

Digitally signed by ANUJ

Providing and fixing in position of customised design ref. images and shop drawing as approveds Conference Table

( T10/T10a ) with Decorative Veneer as approved of required size:

- The conference table top shall be having depth and height for each seating 750mm, table top shall be made out of

40mm thick commercial ply of MR grade (Make: Sumo /Century Architect Ply /Durian /Archid ply /Greenlam Club) IS

303 : 1989 on both side of approved color and contained the thickness shall be 40mm (12mm Plywood + 16mm baton

between both the plywood + 12mm Plywood). For additional strength wooden framing should be provided between

both the plywood of table top total 06 numbers vertical baton size 16mm x 25mm x 750 long and 04 numbers

horizontal baton 16mm x 25mm x 1500 long to be used.

-450 mm high modesty panel and legs made of 18mm thick marine ply with polished veneer pasted on front side and

laminate on inner side, edges will be sealed with veneer. Legs with PVC shoes. Complete table having a knock down

system on mini fitting. Each module to have 1nos. metal brush flapper with metal tray made of CRCA steel for wire

management and electrical & data switch socket mounting provision.

- The side panel / vertical support shall be made out of 18mm thick commercial ply of MR grade (Make: Sumo

/Century Architect Ply /Durian /Archid ply /Greenlam Club) IS 303 : 1989 shall be supporting below the working table

top and front modesty shall be made out of 18mm thick commercial ply of MR grade (Make: Century Architect Ply

/Durian /Archid ply /Greenlam Club) IS 303 : 1989 having height of 650 mm to 700 mm shall be fixed at front side of

table top. Vertical support shall be giving after two seating of minimum of 1500mm intervals.

- Table top surface, both sides of vertical support/ side panel and both sides of modesty shall be pasted with 3.50 to

4.00 mm thick veneer (Make : Archid ply/ Durian/ Archid /Century/ Duro) with hot pressed glue/ adhesive of approved

- Balancing Laminate pasted below the table top shall be thickness of 0.60 mm in gloss / matt finish with high density (L)1500x(W)750x(H)750-24no

9 Confrence table protective surface layer pasted with hot pressed glue including cost of glue/ adhesive of approved quality. +750X750X750*3 no sqm 60 27,382.00 16,42,920.00

- There is a provision of Openable raceways size 1500 (L) x200 (D) x200 (H) mm for operating with double end lock ( part size)

attached below the table top for all data and electric wiring flow should be made out of 18mm thick commercial ply of

MR grade (Make: Sumo/Century Architect Ply /Durian /Archid ply /Greenlam Club) IS 303 : 1989 including with

0.60mm thick laminate (Make: Cedar Lam /Durian /Archid ply /IPL /Royal Touch) IS 2046 : 1995 matching with

tabletop color.

- Raceway having cut outs of required sizes for installing electric switch boards ( switch samples provided by client)

there will be separate slots for passage of data and electrical wires. The frames designed to easily handle CAT6 wire

at entry points. Two numbers of powder coated MS tube size 50 x 50 x 1.2mm thick should be provided for electrical

& data cable flow.

- The working or non-working edges shall be provided with veneer edge binding using with special hot melt glue at hot

temperature. All necessary hardware/ fitting/ hinges etc. of approved quality (Make: Ebco/Hettich/Kitch/ Hafele).

- Veneer to be use is American Oak/ Steam Beach or similar price of make Archid ply/ Durian/ Century/ Duro.

- All veneered portion to be polished minimum four layered of PU coating with sprayed finish in desired shade using

- For installation of table wooden dowels and minifix to use for additional support.

- All Complete job as per direction of Engineer -in –Charge.

- For payment purpose top surface area/ plan area will be measured.

Providing and fixing in position of customised design ref. images and shop drawing as approveds Sliding Tile Base

Workstation ( T-7) including drawer unit as per sizes:

- Free standing partition height 1200mm and should be minimum of 55mm thick. Partition inner frame is 1.1mm thick

mild steel. Horizontal and vertical trims are made out of extruded aluminium of 1.0mm thick.

- All Panels/trims shall be powder coated with 50 microns. Aluminium trims are elegantly fixed with special fixtures in

the partition. The framework shall be fitted with 9mm thick pre laminated Particle tiles of approved shade.

- Partition shall have provision for pin up board with fabric/ white marker/ laminated of approved shade.

- Partition framework shall have adequate provisions for the movement of electric data cables at desired 2 levels; one

at skirting and another above / below the table top. Panel have cut-outs of required sizes for installing electric switch

boards ( switch samples provided by client) there will be separate slots for passage of data and electrical wires. The

frames designed to easily handle CAT6 wire at entry points. The complete partitioning work shall be carried out as per

the approved drawing.

- Balancing Laminate pasted on below the top shall be thickness of 0.60mm in gloss / matt finish with high density

protective surface layer pasted with hot pressed glue including cost of glue/ adhesive of approved quality.

10 E3-E5 - Table top for workstation shall be made up of 25mm thick commercial ply of MR grade (Make: Sumo /Century (L)1400x(W) 600x (H) 750 Each 120 43,523.00 52,22,760.00

Architect Ply /Durian /Archid ply /Greenlam Club) IS 303 : 1989 including with 1mm thick decorative / coloured high

pressure laminated sheet (Make: Cedar Lam /Durian /Archid ply/Archid / IPL /Royal Touch) with hot pressed glue

including cost of glue/ adhesive of approved quality.

- Side panel shall be made out of 18/19mm thick commercial ply of MR grade (Make: Sumo/Century Architect Ply

/Durian /Archid /Greenlam Club) IS 303 : 1989 including with 1mm thick laminate (Make: Cedar Lam /Durian /Archid

ply /IPL Archid/ Royal Touch) IS 2046 : 1995 on both side matching with tabletop and contained the thickness shall be

- The working or non-working edges shall be provided with matching machine pressed 2mm thick PVC edging using

with special hot melt glue at hot temperature. Metal Keyboard with telescopic channel for smooth operation.

- Metal CPU trolley with lockable castors for smooth operation on floor.

-All CRCA steel components / parts powder coated of 50-60 micron. All necessary hardware/ fitting/ hinges/ tower

bolts/ handles etc. of approved quality (Make: Ebco/Hettich/Kitch).

- All Complete job as desired and direction of Engineer -in –Charge. .

Digitally signed by ANUJ

Providing and fixing in position of customised design ref. images and shop drawing as approveds Sliding Tile Base

Workstation ( T-8) including drawer unit as per sizes:

- Free standing partition height 1200mm and should be minimum of 55mm thick. Partition inner frame is 1.1mm thick

mild steel. Horizontal and vertical trims are made out of extruded aluminium of 1.0mm thick.

- All Panels/trims shall be powder coated with 50 microns. Aluminium trims are elegantly fixed with special fixtures in

the partition. The framework shall be fitted with 9mm thick pre laminated Particle tiles of approved shade.

- Partition shall have provision for pin up board with fabric/ white marker/ laminated of approved shade.

- Partition framework shall have adequate provisions for the movement of electric data cables at desired 2 levels; one

at skirting and another above / below the table top. Panel have cut-outs of required sizes for installing electric switch

boards ( switch samples provided by client) there will be separate slots for passage of data and electrical wires. The

frames designed to easily handle CAT6 wire at entry points. The complete partitioning work shall be carried out as per

the approved drawing.

- Balancing Laminate pasted on below the top shall be thickness of 0.60mm in gloss / matt finish with high density

protective surface layer pasted with hot pressed glue including cost of glue/ adhesive of approved quality.

11 E2 & below - Table top for workstation shall be made up of 25mm thick commercial ply of MR grade (Make: Sumo /Century (L)1200x(W) 600x (H) 750 Each 89 41,346.00 36,79,794.00

Architect Ply /Durian /Archid ply /Greenlam Club) IS 303 : 1989 including with 1mm thick decorative / coloured high

pressure laminated sheet (Make: Cedar Lam /Durian /Archid ply/Archid / IPL /Royal Touch) with hot pressed glue

including cost of glue/ adhesive of approved quality.

- Side panel shall be made out of 18/19mm thick commercial ply of MR grade (Make: Sumo/Century Architect Ply

/Durian /Archid /Greenlam Club) IS 303 : 1989 including with 1mm thick laminate (Make: Cedar Lam /Durian /Archid

ply /IPL Archid/ Royal Touch) IS 2046 : 1995 on both side matching with tabletop and contained the thickness shall be

- The working or non-working edges shall be provided with matching machine pressed 2mm thick PVC edging using

with special hot melt glue at hot temperature. Metal Keyboard with telescopic channel for smooth operation.

- Metal CPU trolley with lockable castors for smooth operation on floor.

-All CRCA steel components / parts powder coated of 50-60 micron. All necessary hardware/ fitting/ hinges/ tower

bolts/ handles etc. of approved quality (Make: Ebco/Hettich/Kitch).

- All Complete job as desired and direction of Engineer -in –Charge. .

Providing and fixing in position of customised design ref. images and shop drawing as approved Meeting table (T- 9)

with decorative laminate as approved of required size:

- Table top shall be made out of 24mm thick commercial ply of MR grade (Make: Sumo /Century Architect Ply /Durian

/Archid ply /Greenlam Club) IS 303 : 1989

- The vertical support shall be made out of 18mm thick commercial ply of MR grade (Make: Sumo /Century Architect

Ply /Durian /Archid ply /Greenlam Club) IS 303 : 1989 and modesty shall be made out of 18mm thick commercial ply of

MR grade (Make: Sumo /Century Architect Ply /Durian /Archid ply /Greenlam Club) IS 303 : 1989 having height of 650

mm to 700 mm shall be fixed at mid of table top.

- Table top surface shall be pasted with 1.00 mm thick decorative / coloured high pressure laminated sheet (Make:

Cedar Lam /Durian /Archid ply/ Archid /IPL /Royal Touch) with hot pressed glue including cost of glue/ adhesive of

approved quality.

- Balancing Laminate shall be pasted below the table top, both sides of vertical support/ side panel and both sides of

12 AUDITOR TABLE modesty shall be thickness of 0.60 mm thick decorative / coloured in gloss / matt finish with high density protective (3000X1500X750) *1 sqm 5 38,527.00 1,92,635.00

surface layer pasted with hot pressed glue including cost of glue/ adhesive of approved quality.

- Raceway having cut outs of required sizes for installing electric switch boards ( switch samples provided by client)

there will be separate slots for passage of data and electrical wires. The frames designed to easily handle CAT6 wire

at entry points.

- The working or non-working edges shall be provided with matching machine pressed 2mm thick PVC edging using

with special hot melt glue at hot temperature. All necessary hardware/ fitting etc. of approved quality (Make:

Ebco/Hettich/Kitch/ Hafele)..

- For installation of table wooden dowels and minifix to use for additional support.

- All complete as desired and as per direction and satisfaction of Engineer-in-charge.

For payment purpose top surface area will be measured.

Providing and fixing in position of customised design ref. images and shop drawing as approved Dinning Table ( T 11)

with first class solid teak wood frame with 12mm thick beveled edge toughened glass top to be provided. PU Polishing –

General Holes and indentations on surface shall be filled with putty made of whiting and linseed oil. The pad shall be

13 DINING TABLE moistened with polish and rubbed hard on the surface applying the polish sparingly but uniformly and completely over the (L)900x(D) 900x(H)750 Each 5 29,183.00 1,45,915.00

entire surface. Another coat shall be applied in the same way after the first coat has dried sufficiently. Finishing coats

shall be sprayed on the surface in 2 coats or as required till the satisfied result, using PU/melamine polish of approved

make. All complete as per direction and satisfaction of Engineer-in-charge.

Digitally signed by ANUJ

Providing and fixing in position of customised design ref. images and shop drawing as approved Meeting table (T-

12) with decorative laminate as approved of required size:

- Table top shall be made out of 24mm thick commercial ply of MR grade (Make: Sumo /Century Architect Ply /Durian

/Archid ply /Greenlam Club) IS 303 : 1989

- The vertical support shall be made out of 18mm thick commercial ply of MR grade (Make: Sumo /Century Architect

Ply /Durian /Archid ply /Greenlam Club) IS 303 : 1989 and modesty shall be made out of 18mm thick commercial ply of

MR grade (Make: Sumo /Century Architect Ply /Durian /Archid ply /Greenlam Club) IS 303 : 1989 having height of 650

mm to 700 mm shall be fixed at mid of table top.

- Table top surface shall be pasted with 1.00 mm thick decorative / coloured high pressure laminated sheet (Make:

Cedar Lam /Durian /Archid ply/ Archid /IPL /Royal Touch) with hot pressed glue including cost of glue/ adhesive of

approved quality.

- Balancing Laminate shall be pasted below the table top, both sides of vertical support/ side panel and both sides of

14 MEETING TABLE modesty shall be thickness of 0.60 mm thick decorative / coloured in gloss / matt finish with high density protective (2400X1200X750) *8 sqm 24 24,663.00 5,91,912.00

surface layer pasted with hot pressed glue including cost of glue/ adhesive of approved quality.

- Raceway having cut outs of required sizes for installing electric switch boards ( switch samples provided by client)

there will be separate slots for passage of data and electrical wires. The frames designed to easily handle CAT6 wire

at entry points.

- The working or non-working edges shall be provided with matching machine pressed 2mm thick PVC edging using

with special hot melt glue at hot temperature. All necessary hardware/ fitting etc. of approved quality (Make:

Ebco/Hettich/Kitch/ Hafele)..

- For installation of table wooden dowels and minifix to use for additional support.

- All complete as desired and as per direction and satisfaction of Engineer-in-charge.

For payment purpose top surface area will be measured.

Control Room Furniture/Operator Console

Workspace make New Modular Control Desk for Provision of 02 nos. 24'' Monitors made in " Dynamic XE "system.

1. Table-top:The material of the working surface shall be minimum 25 mm thick MDF with High-Pressure laminate.

Adequate space shall be provided on the desktop for writing area, to accommodate the operator workstation, mouse,

telephone console and other miscellaneous items. Proposed console shall not have any hazardous substances.

2.1 Made of heavy duty extruded vertical and horizontal aluminium profiles. The extrusions shall be duly powder

coated with 40+microns over all surfaces. All sheet metal parts shall be finished with a durable, black, electrostatic

powder coating. The structure shall allow easy assembly of shutters and gland plate in extremely rigid manner.

2.2 To allow future extension and expansion, a weld-free system shall be proposed. Interconnecting joints shall not be

The structure shall be rigid enough to withstand BIFMA X5.5 tests.The structure shall allow easy assembly of hinged

shutters, table top, side leg and gland plate in extremely rigid manner.

3. Modular removable PU nosing: The front edge of consoles is the component which comes in frequent contact of the

The soft polyurethane edge is meant to prevent injury (accidental impact) to operator during emergency and it also

reduces the contact stress. In case of damage to this edge the desk design shall permit quick & easy replacement

within half an hour without taking any shutdowns or removal of the tabletops. Audit certified design feature of modular

PU Edge: High-density poly-urethane moulded on industrial grade aluminium core to form 50mm deep tapered edge to

be installed on worktop. In case of damage or wear, the edge shall be mechanically replaceable within 30 minutes

without opening or removing the worktop.

4. Shutters: - The shutter tiles shall be made of minimum 1mm Thick MS sheet with Powder coated finish. The shutter

tile shall be class A fire rated as per ASTM e84 (from UL/Intertek) for surface burning characteristics.

5 Side Legs: - Extreme end side leg shall have sandwich construction made up of 18mm thick laminated MDF

boards/Alumina Tri-hydrate and acrylic resin material.The central portion of the side leg shall feature illuminated strip

SOC CONTROL on the periphery.The proposed console shall be Greenguard Gold certified.

6. Desktop Automation: - Hassle free ergonomic operations/adjustments and durability of the product, the console shall

have UL/Intertek audit certified feature on all mechanisms of console. The mechanisms shall be tested & certified for at

least 1000 time synchronous up-down movement of worktop, tilt adjustments, up-down and front-back movement of

monitor base w.r.t.worktop and all these mechanisms shall be operated by using single touch screen.

7 Desktop Lift Mechanism: - Adjustable (Height) Desks (sit-and-stand with step-less automatic height adjustment).

8. Touch Screen: - Programmable touch screen controls shall be provided for operator movements with 20 autosave

preset options related to desk movements/position. The preset shall be used to define the desk configuration.The

integrated illumination strip shall have RGB colors. The Illumination color shall be controlled by this touchscreen for

different scenario like blue for VIP visit, green for Normal Operations and red for emergency etc 9. Height Adjustable

Mechanisms for Monitor Base: - Height adjustable ±3” (±75mm) with respect to tabletop. Height shall be adjusted with

electrical drive. Monitors shall also have depth adjustment feature in horizontal plane up-to 100mm. Independent

electronic powered height adjustment of platform and workspace.

10. Monitor tilt variation with motorized height/tilt/depth adjustment: - Monitor screens tilt shall be adjusted with

electrical drive at desired angle, depth & curvilinear arrangement of screens depending on the operator's ease of

working. It shall be capable for mounting all type of LCD display with dimensions between 17” to 24” using suitable

adapter /additional base plate for complying VESA standards 75 x 75, 100 x 100. All the monitor screens shall have

synchronized tilting with 0 to 60ᵒ from vertical plane by single control, customisable.

All complete as desired and as per direction and satisfaction of Engineer-in-charge. For payment purpose top surface

area will be measured.

Digitally signed by ANUJ

Providing and Placing in position of Main Entrence Reception curve seven seater Sofa cum centre table (750 mm

dia) as per Reference image /photograph or equivqlent as approved. The contemporary customised design &

drawings sofa of Size : (L)600.0cm X (D)75.0cm X (H)75.0cm, seat height 46.0cm, seat depth 51.0cm and back

height 55.0cm, should be upholstered in premium leatherette, this sofa is sleek and comfortable. The wooden frame is

finished in a rich brown polish with split panel seating. The back and seat have medium to firm cushioning for better

posture. The Sofa stands on moulded pvc legs beautiful accents that are slightly curved on the front face of the sofa.

16 MR Each curve defines a seating space which provides for people to be seated comfortably. Finished in a luxurious Each 1 2,30,201.00 2,30,201.00

Leatherette, the sofa exudes a certain class. Seat of Sofa is layered with silicon fibre filling over high density foam.

The seat cushion is made of multi layered foam of density 32(+/-2kg /m3). The seating cushions have 2.75 & 1.75

inches of elastic webbing. The thread used is nylon bonded to provide lasting stitch strength. All complete as per

direction and satisfaction of Engineer-in-charge.

Providing and Placing in position of Three Seater Sofa ( S3) as per Reference image /photograph or equivqlent as

approved. The contemporary customised design & drawings sofa of Size : (L)180.0cm X (D)75.0cm X (H)85.0cm,

seat height 46.0cm, seat depth 51.0cm and back height 55.0cm, should be upholstered in premium leatherette, this

sofa is sleek and comfortable. The wooden frame is finished in a rich brown polish with split panel seating. The back

and seat have medium to firm cushioning for better posture. The Sofa stands on moulded pvc legs beautiful accents

that are slightly curved on the front face of the sofa. Each curve defines a seating space which provides for people to

be seated comfortably. Finished in a luxurious Leatherette, the sofa exudes a certain class. Seat of Sofa is layered

17 MR with silicon fibre filling over high density foam. The seat cushion is made of multi layered foam of density 32(+/-2kg Each 9 58,349.00 5,25,141.00

/m3). The seating cushions have 2.75 & 1.75 inches of elastic webbing. The thread used is nylon bonded to provide

lasting stitch strength. All complete as per direction and satisfaction of Engineer-in-charge.

Providing and Placing in position of Two Seater Sofa ( S2) as per Reference image /photograph or equivqlent as

approved. The contemporary customised design & drawings sofa of Size : (L)150.0cm X (D)75.0cm X (H)85.0cm,

seat height 46.0cm, seat depth 51.0cm and back height 55.0cm, should be upholstered in premium leatherette, this

sofa is sleek and comfortable. The wooden frame is finished in a rich brown polish with split panel seating. The back

and seat have medium to firm cushioning for better posture. The Sofa stands on moulded pvc legs beautiful accents

that are slightly curved on the front face of the sofa. Each curve defines a seating space which provides for people to

be seated comfortably. Finished in a luxurious Leatherette, the sofa exudes a certain class. Seat of Sofa is layered

18 MR with silicon fibre filling over high density foam. The seat cushion is made of multi layered foam of density 32(+/-2kg Each 6 38,893.00 2,33,358.00

/m3). The seating cushions have 2.75 & 1.75 inches of elastic webbing. The thread used is nylon bonded to provide

lasting stitch strength. All complete as per direction and satisfaction of Engineer-in-charge.

Providing and Placing in position of Single Seater Sofa ( S1) as per Reference image /photograph or equivqlent as

approved. The contemporary customised design & drawings sofa of Size : (L)75cm X (D75.0cm X (H)85.0cm, seat

height 46.0cm, seat depth 51.0cm and back height 55.0cm, should be upholstered in premium leatherette, this sofa is

sleek and comfortable. The wooden frame is finished in a rich brown polish with split panel seating. The back and seat

have medium to firm cushioning for better posture. The Sofa stands on moulded pvc legs beautiful accents that are

slightly curved on the front face of the sofa. Each curve defines a seating space which provides for people to be

19 MR seated comfortably. Finished in a luxurious Leatherette, the sofa exudes a certain class. Seat of Sofa is layered with Each 20 27,780.00 5,55,600.00

silicon fibre filling over high density foam. The seat cushion is made of multi layered foam of density 32(+/-2kg /m3).

The seating cushions have 2.75 & 1.75 inches of elastic webbing. The thread used is nylon bonded to provide lasting

stitch strength. All complete as per direction and satisfaction of Engineer-in-charge.

Providing and fixing in position of customised design ref. images and shop drawing as approved Center Table ( T13)

with first class solid teak wood frame with 12mm thick beveled edge toughened glass top to be provided. PU Polishing –

General Holes and indentations on surface shall be filled with putty made of whiting and linseed oil. The pad shall be

moistened with polish and rubbed hard on the surface applying the polish sparingly but uniformly and completely over the

entire surface. Another coat shall be applied in the same way after the first coat has dried sufficiently. Finishing coats

shall be sprayed on the surface in 2 coats or as required till the satisfied result, using PU/melamine polish of approved

make. All complete as per direction and satisfaction of Engineer-in-charge.

Providing and fixing in position of customised design ref. images and shop drawing as approved Side Table ( T14) with

first class solid teak wood frame with 12mm thick beveled edge toughened glass top to be provided. PU Polishing ,

General Holes and indentations on surface shall be filled with putty made of whiting and linseed oil. The pad shall be

moistened with polish and rubbed hard on the surface applying the polish sparingly but uniformly and completely over the

entire surface. Another coat shall be applied in the same way after the first coat has dried sufficiently. Finishing coats

VISITOR SIDE shall be sprayed on the surface in 2 coats or as required till the satisfied result, using PU /melamine polish of approved

TABLE make. All complete as per direction and satisfaction of Engineer-in-charge.

Digitally signed by ANUJ

Providing and fixing in position of customised design ref. images and shop drawing as approved Side Table ( T14a) with

first class solid teak wood frame with 12mm thick beveled edge toughened glass top to be provided. PU Polishing ,

General Holes and indentations on surface shall be filled with putty made of whiting and linseed oil. The pad shall be

moistened with polish and rubbed hard on the surface applying the polish sparingly but uniformly and completely over the (L)600x (D)

22 entire surface. Another coat shall be applied in the same way after the first coat has dried sufficiently. Finishing coats Each 17 29,125.00 4,95,125.00

TABLE 450x(H)450

shall be sprayed on the surface in 2 coats or as required till the satisfied result, using PU /melamine polish of approved

make. All complete as per direction and satisfaction of Engineer-in-charge.

Providing and fixing in position of customised Design & Drawing Storage unit ( ST1 ) with deorative laminate as

approved at all floors of Depth 600 mm of required size all complete as per direction and satisfaction of Engineer-in-

- Storage carcase and shutter shall be made of 18 mm thick commercial plywood of MR grade (Make: Sumo/Century

Architect Ply /Durian /Archid ply /Archid classic/Greenlam Club) IS 303 : 1989 and storage backing shall be 12 mm

thick commercial plywood of MR grade IS 303 : 1989. The gap between 2 shelves should be range from 400 mm as

per the direction of EIC.

- Storage top, sides and front facia shall be shall be pasted with 1.00 mm thick decorative / coloured high pressure

laminated sheet (Make: Cedar Lam /Durian /Archid ply /IPL/Archid /Royal Touch) with hot pressed glue including cost

of glue/ adhesive of approved quality

- Balancing Laminate pasted on storage below the top, back, inner area of storage shall be thickness of 0.60 mm in

gloss / matt finish with high density protective surface layer pasted with hot pressed glue including cost of glue/

STORAGE adhesive of approved quality. 1200X450X2100/

CABINET 01 - The working or non-working edges shall be provided with matching machine pressed 2mm thick PVC edging using 600x450x2100

with special hot melt glue at hot temperature. All necessary hardware/ fitting/ hinges etc. of approved quality (Make:

Ebco/Hettich/Kitch).

- Each shutter should be fixed with 2 / 3 numbers SS butt hinges,round shape multipurpose lock, SS tower bolt of 100

x 10mm, Magnetic double strip catcher. Shutter shall have 100 mm size SS fancy handles (one on each drawer) with

minimum of 6 thread necessary hardware/ fitting/ hinges etc. of approved quality(Make: Ebco/Hettich/Kitch/

Hafele/Sumsung Irex).

- Shelf should have metal stiffener complete end to end for extra load & two numbers heavy duty SS shelf pin on each

- For installation of storage wooden dowels and minifix to use for additional support.

- All complete as per direction and satisfaction of Engineer-in-charge.

- For payment purpose front surface will be measured..

Providing and fixing in position of customised Design & Drawing Storage unit ( ST1 ) with deorative laminate as

approved at all floors of Depth 600 mm of required size all complete as per direction and satisfaction of Engineer-in-

- Storage carcase and shutter shall be made of 18 mm thick commercial plywood of MR grade (Make: Sumo/Century

Architect Ply /Durian /Archid ply /Archid classic/Greenlam Club) IS 303 : 1989 and storage backing shall be 12 mm

thick commercial plywood of MR grade IS 303 : 1989. The gap between 2 shelves should be range from 400 mm as

per the direction of EIC.

- Storage top, sides and front facia shall be shall be pasted with 1.00 mm thick decorative / coloured high pressure

laminated sheet (Make: Cedar Lam /Durian /Archid ply /IPL/Archid /Royal Touch) with hot pressed glue including cost

of glue/ adhesive of approved quality

- Balancing Laminate pasted on storage below the top, back, inner area of storage shall be thickness of 0.60 mm in

gloss / matt finish with high density protective surface layer pasted with hot pressed glue including cost of glue/

STORAGE adhesive of approved quality.

CABINET 02 - The working or non-working edges shall be provided with matching machine pressed 2mm thick PVC edging using

with special hot melt glue at hot temperature. All necessary hardware/ fitting/ hinges etc. of approved quality (Make:

Ebco/Hettich/Kitch).

- Each shutter should be fixed with 2 / 3 numbers SS butt hinges,round shape multipurpose lock, SS tower bolt of 100

x 10mm, Magnetic double strip catcher. Shutter shall have 100 mm size SS fancy handles (one on each drawer) with

minimum of 6 thread necessary hardware/ fitting/ hinges etc. of approved quality(Make: Ebco/Hettich/Kitch/

Hafele/Sumsung Irex).

- Shelf should have metal stiffener complete end to end for extra load & two numbers heavy duty SS shelf pin on each

- For installation of storage wooden dowels and minifix to use for additional support.

- All complete as per direction and satisfaction of Engineer-in-charge.

- For payment purpose front surface will be measured..

Digitally signed by ANUJ

Providing and fixing in position of customised Design & Drawing Storage unit ( ST2 ) with deorative laminate as

approved at all floors of Depth 600 mm of required size all complete as per direction and satisfaction of Engineer-in-

- Storage carcase and shutter shall be made of 18 mm thick commercial plywood of MR grade (Make: Sumo/Century

Architect Ply /Durian /Archid ply /Archid classic/Greenlam Club) IS 303 : 1989 and storage backing shall be 12 mm

thick commercial plywood of MR grade IS 303 : 1989. The gap between 2 shelves should be range from 400 mm as

per the direction of EIC.

- Storage top, sides and front facia shall be shall be pasted with 1.00 mm thick decorative / coloured high pressure

laminated sheet (Make: Cedar Lam /Durian /Archid ply /IPL/Archid /Royal Touch) with hot pressed glue including cost

of glue/ adhesive of approved quality

- Balancing Laminate pasted on storage below the top, back, inner area of storage shall be thickness of 0.60 mm in

gloss / matt finish with high density protective surface layer pasted with hot pressed glue including cost of glue/

STORAGE adhesive of approved quality.

CABINET O2 - The working or non-working edges shall be provided with matching machine pressed 2mm thick PVC edging using

with special hot melt glue at hot temperature. All necessary hardware/ fitting/ hinges etc. of approved quality (Make:

Ebco/Hettich/Kitch).

- Each shutter should be fixed with 2 / 3 numbers SS butt hinges,round shape multipurpose lock, SS tower bolt of 100

x 10mm, Magnetic double strip catcher. Shutter shall have 100 mm size SS fancy handles (one on each drawer) with

minimum of 6 thread necessary hardware/ fitting/ hinges etc. of approved quality(Make: Ebco/Hettich/Kitch/

Hafele/Sumsung Irex).

- Shelf should have metal stiffener complete end to end for extra load & two numbers heavy duty SS shelf pin on each

- For installation of storage wooden dowels and minifix to use for additional support.

- All complete as per direction and satisfaction of Engineer-in-charge.

- For payment purpose front surface will be measured..

Providing & Placing in position of High back with leather upholstery chair ( C1 ) as per Reference image

/photograph or equivqlent as approved . The cushioned seat and back shall be made of 1.2+/-0.1cm hot pressed

plywood is upholstered with leather and moulded high resilience polyurethane foam of density 45±2 kg/m³, & hardness

load of 16±2 kgf as per IS:7888 for 25% compression. Seat Size is 47.0 W cm + 2cm W x 48.0 D cm + 2 cm . The

back is cushioned made of PU foam with insitu moulded M.S. ERW round tube of size 1.9 cm ± 0.03cm x 0.16 ± 0.02

cm, upholstered with leather. The back size is 48 W cm + 2 cm x 77 D cm + 2 cm . The armrest top is molded from

polyurethane and mounted on to a drop lift adjustable type tubular armrest support made of Ø3.81±0.03cm x

0.2±0.01cm thick M.S. ERW tube having chrome plated finish. The armrest is height adjustable up to 6.5±0.5 cm in 5

steps. The adjustable tilting mechanism is designed with following features : 360° revolving type, front-pivot for tilt with

feet resting on ground and continuous lumbar support ensuring more comfort, tilt tension adjustment can be operated

in seating position, 5position tilt limiter giving option of variable tilt angle to the chair, Seat/back tilt ratio 1:2, Seat

depth adjustment is integrated in the seat through a sliding mechanism. Seat depth adjustment range is of 6.0±0.5cm.

It can be adjusted in the range of 7.42±0.5 comfort the comfortable back support to suit individual need. The

pneumatic height adjustment has an adjustment stroke of 10.0±0.3cm. The pedestal is high pressure die cast

polished aluminium & fitted with 5 nos. of twin wheel castors. The pedestal is 65.0±0.5cm pitch centre dia.

(75.0±1.0cm with castors). 5 nos. of twin wheel castors are injection moulded in plastic having 6.0±0.1cm wheel

diameter and assembled to pedestal. All complete as per direction and satisfaction of Engineer-in-charge.

Providing & Placing in position of medium back with leather upholstery chair ( C1a ) as per Reference image

/photograph or equivqlent as approved . The cushioned seat and back shall be made of 1.2+/-0.1cm hot pressed

plywood is upholstered with leather and moulded high resilience polyurethane foam of density 45±2 kg/m³, & hardness

load of 16±2 kgf as per IS:7888 for 25% compression. Seat Size is 47.0 W cm + 2cm W x 48.0 D cm + 2 cm . The

back is cushioned made of PU foam with insitu moulded M.S. ERW round tube of size 1.9 cm ± 0.03cm x 0.16 ± 0.02

cm, upholstered with leather. The back size is 48 W cm + 2 cm x 77 D cm + 2 cm . The armrest top is molded from

polyurethane and mounted on to a drop lift adjustable type tubular armrest support made of Ø3.81±0.03cm x

0.2±0.01cm thick M.S. ERW tube having chrome plated finish. The armrest is height adjustable up to 6.5±0.5 cm in 5

steps. The adjustable tilting mechanism is designed with following features : 360° revolving type, front-pivot for tilt with

feet resting on ground and continuous lumbar support ensuring more comfort, tilt tension adjustment can be operated

27 in seating position, 5position tilt limiter giving option of variable tilt angle to the chair, Seat/back tilt ratio 1:2, Seat Each 4 33,446 1,33,784.00

depth adjustment is integrated in the seat through a sliding mechanism. Seat depth adjustment range is of 6.0±0.5cm.

It can be adjusted in the range of 7.42±0.5 comfort the comfortable back support to suit individual need. The

pneumatic height adjustment has an adjustment stroke of 10.0±0.3cm. The pedestal is high pressure die cast

polished aluminium & fitted with 5 nos. of twin wheel castors. The pedestal is 65.0±0.5cm pitch centre dia.

(75.0±1.0cm with castors). 5 nos. of twin wheel castors are injection moulded in plastic having 6.0±0.1cm wheel

diameter and assembled to pedestal. All complete as per direction and satisfaction of Engineer-in-charge.

Digitally signed by ANUJ

Providing & Placing in position of High back with leather upholstery chair ( C2) as per Reference image

/photograph or equivqlent as approved . The cushioned seat and back shall be made of 1.2+/-0.1cm hot pressed

plywood is upholstered with leather and moulded high resilience polyurethane foam of density 45±2 kg/m³, & hardness

load of 16±2 kgf as per IS:7888 for 25% compression. Seat Size is 47.0 W cm + 2cm W x 48.0 D cm + 2 cm . The

back is cushioned made of PU foam with insitu moulded M.S. ERW round tube of size 1.9 cm ± 0.03cm x 0.16 ± 0.02

cm, upholstered with leather. The back size is 48 W cm + 2 cm x 77 D cm + 2 cm . The armrest top is molded from

polyurethane and mounted on to a drop lift adjustable type tubular armrest support made of Ø3.81±0.03cm x

0.2±0.01cm thick M.S. ERW tube having chrome plated finish. The armrest is height adjustable up to 6.5±0.5 cm in 5

steps. The adjustable tilting mechanism is designed with following features : 360° revolving type, front-pivot for tilt with

feet resting on ground and continuous lumbar support ensuring more comfort, tilt tension adjustment can be operated

28 DIRECTOR CHAIR in seating position, 5position tilt limiter giving option of variable tilt angle to the chair, Seat/back tilt ratio 1:2, Seat Each 9 33,446 3,01,014.00

depth adjustment is integrated in the seat through a sliding mechanism. Seat depth adjustment range is of 6.0±0.5cm.

It can be adjusted in the range of 7.42±0.5 comfort the comfortable back support to suit individual need. The

pneumatic height adjustment has an adjustment stroke of 10.0±0.3cm. The pedestal is high pressure die cast

polished aluminium & fitted with 5 nos. of twin wheel castors. The pedestal is 65.0±0.5cm pitch centre dia.

(75.0±1.0cm with castors). 5 nos. of twin wheel castors are injection moulded in plastic having 6.0±0.1cm wheel

diameter and assembled to pedestal. All complete as per direction and satisfaction of Engineer-in-charge.

Providing & Placing in position of Medium back with leather upholstery chair ( C2a) as per Reference image

/photograph or equivqlent as approved. Chair seat shall be made up of 1.2+/-0.1cm hot pressed plywood upholstered

in mesh fabric and moulded with PU foam superior load capacity of over 135 kgs, Seat Size is 45.0 W cm x 47.0 D

cm. Chair having a back in one piece curved design shall be made of injection moulded plastic outer & inner

upholstered with breathable nylon mesh superior load capacity of over 135 kgs. The back size is 46.0 W cm x 58.0 H

cm. Chair breathable nylon mesh having with creative tree detailing on the back, so when you look at it from afar it

feels as if a tree is emerging from the roots to the branches and leaves on the top. The leaves add function to the

design height adjustable lumbar support for improving of seating capacity and lumbar support. The armrest top is

moulded from polyurethane and mounted on to a drop lift adjustable type tubular armrest support made of

Ø3.81±0.03cm x 0.2±0.01cm thick M.S. ERW tube having chrome plated finish. The armrest is height adjustable up to

6.5±0.5 cm in 5 steps and having the adjustment of forward/ backword feature for extra support and comfort. The

DIRECTOR armrest is scratch and whether resistant. The arm rests are fitted to the seat with a connecting strip assembly made of

29 5mm of HR steel. The adjustable tilting mechanism is designed with following features : 360° revolving type, front- Each 15 32,233 4,83,495.00

pivot for tilt with feet resting on ground and tilt tension adjustment can be operated in seating position, 5 position tilt

limiter giving option of variable tilt angle to the chair, Seat/back tilt ratio 1:2 with synchro tilt mechanism. The

pneumatic height adjustment has an adjustment stroke of 10.0±0.3cm, shall be operated at 30kgs extension force and

lever should be attached right side between injection moulded plastic outer & inner of the seat frame. The pedestal is

high pressure die cast polished aluminium 65.0±0.5cm pitch centre dia. (75.0±1.0cm with castors). 5 nos. of twin

wheel castors are injection moulded in nylon having 6.0±0.1cm wheel diameter and assembled to pedestal. The

telescopic bellows is 3 piece telescopic type and injection moulded in black polyurethane. Complete as per direction of

Engineer -in –Charge.

Providing & Placing in position of High back with leatheritte upholstery chair ( C3 ) as per Reference image

/photograph or equivqlent as approved . The cushioned seat and back shall be made of 1.2+/-0.1cm hot pressed

plywood is upholstered with leather and moulded high resilience polyurethane foam of density 45±2 kg/m³, & hardness

load of 16±2 kgf as per IS:7888 for 25% compression. Seat Size is 47.0 W cm + 2cm W x 48.0 D cm + 2 cm . The

back is cushioned made of PU foam with insitu moulded M.S. ERW round tube of size 1.9 cm ± 0.03cm x 0.16 ± 0.02

cm, upholstered with leather. The back size is 48 W cm + 2 cm x 77 D cm + 2 cm . The armrest top is molded from

polyurethane and mounted on to a drop lift adjustable type tubular armrest support made of Ø3.81±0.03cm x

0.2±0.01cm thick M.S. ERW tube having chrome plated finish. The armrest is height adjustable up to 6.5±0.5 cm in 5

steps. The adjustable tilting mechanism is designed with following features : 360° revolving type, front-pivot for tilt with

feet resting on ground and continuous lumbar support ensuring more comfort, tilt tension adjustment can be operated

30 E 7,8&9 CHAIR in seating position, 5position tilt limiter giving option of variable tilt angle to the chair, Seat/back tilt ratio 1:2, Seat Each 61 27,727 16,91,347.00

depth adjustment is integrated in the seat through a sliding mechanism. Seat depth adjustment range is of 6.0±0.5cm.

It can be adjusted in the range of 7.42±0.5 comfort the comfortable back support to suit individual need. The

pneumatic height adjustment has an adjustment stroke of 10.0±0.3cm. The pedestal is high pressure die cast

polished aluminium & fitted with 5 nos. of twin wheel castors. The pedestal is 65.0±0.5cm pitch centre dia.

(75.0±1.0cm with castors). 5 nos. of twin wheel castors are injection moulded in plastic having 6.0±0.1cm wheel

diameter and assembled to pedestal. All complete as per direction and satisfaction of Engineer-in-charge.

Digitally signed by ANUJ

Providing & Placing in position of Medium back with leatheritte upholstery chair ( C3a ) as per Reference image

/photograph or equivqlent as approved. Chair seat shall be made up of 1.2+/-0.1cm hot pressed plywood upholstered

in mesh fabric and moulded with PU foam superior load capacity of over 135 kgs, Seat Size is 45.0 W cm x 47.0 D

cm. Chair having a back in one piece curved design shall be made of injection moulded plastic outer & inner

upholstered with breathable nylon mesh superior load capacity of over 135 kgs. The back size is 46.0 W cm x 58.0 H

cm. Chair breathable nylon mesh having with creative tree detailing on the back, so when you look at it from afar it

feels as if a tree is emerging from the roots to the branches and leaves on the top. The leaves add function to the

design height adjustable lumbar support for improving of seating capacity and lumbar support. The armrest top is

moulded from polyurethane and mounted on to a drop lift adjustable type tubular armrest support made of

Ø3.81±0.03cm x 0.2±0.01cm thick M.S. ERW tube having chrome plated finish. The armrest is height adjustable up to

6.5±0.5 cm in 5 steps and having the adjustment of forward/ backword feature for extra support and comfort. The

armrest is scratch and whether resistant. The arm rests are fitted to the seat with a connecting strip assembly made of

E 7,8&9 VISITOR 5mm of HR steel. The adjustable tilting mechanism is designed with following features : 360° revolving type, front-

CHAIR pivot for tilt with feet resting on ground and tilt tension adjustment can be operated in seating position, 5 position tilt

limiter giving option of variable tilt angle to the chair, Seat/back tilt ratio 1:2 with synchro tilt mechanism. The

pneumatic height adjustment has an adjustment stroke of 10.0±0.3cm, shall be operated at 30kgs extension force and

lever should be attached right side between injection moulded plastic outer & inner of the seat frame. The pedestal is

high pressure die cast polished aluminium 65.0±0.5cm pitch centre dia. (75.0±1.0cm with castors). 5 nos. of twin

wheel castors are injection moulded in nylon having 6.0±0.1cm wheel diameter and assembled to pedestal. The

telescopic bellows is 3 piece telescopic type and injection moulded in black polyurethane. Complete as per direction of

Engineer -in –Charge.

Providing & Placing in position of Medium back with leatheritte upholstery chair ( C4 ) as per Reference image

/photograph or equivqlent as approved. Chair seat shall be made up of 1.2+/-0.1cm hot pressed plywood upholstered

in mesh fabric and moulded with PU foam superior load capacity of over 135 kgs, Seat Size is 45.0 W cm x 47.0 D

cm. Chair having a back in one piece curved design shall be made of injection moulded plastic outer & inner

upholstered with breathable nylon mesh superior load capacity of over 135 kgs. The back size is 46.0 W cm x 58.0 H

cm. Chair breathable nylon mesh having with creative tree detailing on the back, so when you look at it from afar it

feels as if a tree is emerging from the roots to the branches and leaves on the top. The leaves add function to the

design height adjustable lumbar support for improving of seating capacity and lumbar support. The armrest top is

moulded from polyurethane and mounted on to a drop lift adjustable type tubular armrest support made of

Ø3.81±0.03cm x 0.2±0.01cm thick M.S. ERW tube having chrome plated finish. The armrest is height adjustable up to

6.5±0.5 cm in 5 steps and having the adjustment of forward/ backword feature for extra support and comfort. The

E-6 CHAIR armrest is scratch and whether resistant. The arm rests are fitted to the seat with a connecting strip assembly made of

( work station) 5mm of HR steel. The adjustable tilting mechanism is designed with following features : 360° revolving type, front-

pivot for tilt with feet resting on ground and tilt tension adjustment can be operated in seating position, 5 position tilt

limiter giving option of variable tilt angle to the chair, Seat/back tilt ratio 1:2 with synchro tilt mechanism. The

pneumatic height adjustment has an adjustment stroke of 10.0±0.3cm, shall be operated at 30kgs extension force and

lever should be attached right side between injection moulded plastic outer & inner of the seat frame. The pedestal is

high pressure die cast polished aluminium 65.0±0.5cm pitch centre dia. (75.0±1.0cm with castors). 5 nos. of twin

wheel castors are injection moulded in nylon having 6.0±0.1cm wheel diameter and assembled to pedestal. The

telescopic bellows is 3 piece telescopic type and injection moulded in black polyurethane. Complete as per direction of

Engineer -in –Charge.

Providing & Placing in position of Medium back with leatheritte upholstery chair ( C5 ) as per Reference image

/photograph or equivqlent as approved. Chair seat shall be made up of 1.2+/-0.1cm hot pressed plywood upholstered

in mesh fabric and moulded with PU foam superior load capacity of over 135 kgs, Seat Size is 45.0 W cm x 47.0 D

cm. Chair having a back in one piece curved design shall be made of injection moulded plastic outer & inner

upholstered with breathable nylon mesh superior load capacity of over 135 kgs. The back size is 46.0 W cm x 58.0 H

cm. Chair breathable nylon mesh having with creative tree detailing on the back, so when you look at it from afar it

feels as if a tree is emerging from the roots to the branches and leaves on the top. The leaves add function to the

design height adjustable lumbar support for improving of seating capacity and lumbar support. The armrest top is

moulded from polyurethane and mounted on to a drop lift adjustable type tubular armrest support made of

Ø3.81±0.03cm x 0.2±0.01cm thick M.S. ERW tube having chrome plated finish. The armrest is height adjustable up to

6.5±0.5 cm in 5 steps and having the adjustment of forward/ backword feature for extra support and comfort. The

E-5,3,2, control armrest is scratch and whether resistant. The arm rests are fitted to the seat with a connecting strip assembly made of

room & below 5mm of HR steel. The adjustable tilting mechanism is designed with following features : 360° revolving type, front-

CHAIR pivot for tilt with feet resting on ground and tilt tension adjustment can be operated in seating position, 5 position tilt

limiter giving option of variable tilt angle to the chair, Seat/back tilt ratio 1:2 with synchro tilt mechanism. The

pneumatic height adjustment has an adjustment stroke of 10.0±0.3cm, shall be operated at 30kgs extension force and

lever should be attached right side between injection moulded plastic outer & inner of the seat frame. The pedestal is

high pressure die cast polished aluminium 65.0±0.5cm pitch centre dia. (75.0±1.0cm with castors). 5 nos. of twin

wheel castors are injection moulded in nylon having 6.0±0.1cm wheel diameter and assembled to pedestal. The

telescopic bellows is 3 piece telescopic type and injection moulded in black polyurethane. Complete as per direction of

Engineer -in –Charge.

Digitally signed by ANUJ

Providing & Placing in position of Medium back with leatheritte upholstery chair ( C6 ) as per Reference image

/photograph or equivqlent as approved. Chair seat shall be made up of 1.2+/-0.1cm hot pressed plywood upholstered

in mesh fabric and moulded with PU foam superior load capacity of over 135 kgs, Seat Size is 45.0 W cm x 47.0 D

cm. Chair having a back in one piece curved design shall be made of injection moulded plastic outer & inner

upholstered with breathable nylon mesh superior load capacity of over 135 kgs. The back size is 46.0 W cm x 58.0 H

cm. Chair breathable nylon mesh having with creative tree detailing on the back, so when you look at it from afar it

feels as if a tree is emerging from the roots to the branches and leaves on the top. The leaves add function to the

design height adjustable lumbar support for improving of seating capacity and lumbar support. The armrest top is

moulded from polyurethane and mounted on to a drop lift adjustable type tubular armrest support made of

Ø3.81±0.03cm x 0.2±0.01cm thick M.S. ERW tube having chrome plated finish. The armrest is height adjustable up to

6.5±0.5 cm in 5 steps and having the adjustment of forward/ backword feature for extra support and comfort. The

armrest is scratch and whether resistant. The arm rests are fitted to the seat with a connecting strip assembly made of

34 5mm of HR steel. The adjustable tilting mechanism is designed with following features : 360° revolving type, front- Each 3 25863.00 77,589.00

pivot for tilt with feet resting on ground and tilt tension adjustment can be operated in seating position, 5 position tilt

limiter giving option of variable tilt angle to the chair, Seat/back tilt ratio 1:2 with synchro tilt mechanism. The

pneumatic height adjustment has an adjustment stroke of 10.0±0.3cm, shall be operated at 30kgs extension force and

lever should be attached right side between injection moulded plastic outer & inner of the seat frame. The pedestal is

high pressure die cast polished aluminium 65.0±0.5cm pitch centre dia. (75.0±1.0cm with castors). 5 nos. of twin

wheel castors are injection moulded in nylon having 6.0±0.1cm wheel diameter and assembled to pedestal. The

telescopic bellows is 3 piece telescopic type and injection moulded in black polyurethane. Complete as per direction of

Engineer -in –Charge.

Providing & Placing in position of Medium back with leatheritte upholstery chair ( Meeting Room ) as per

Reference image /photograph or equivqlent as approved . The cushioned seat and back shall be made of 1.2+/-0.1cm

hot pressed plywood is upholstered with leather and moulded high resilience polyurethane foam of density 45±2

kg/m³, & hardness load of 16±2 kgf as per IS:7888 for 25% compression. Seat Size is 47.0 W cm + 2cm W x 48.0 D

cm + 2 cm . The back is cushioned made of PU foam with insitu moulded M.S. ERW round tube of size 1.9 cm ±

0.03cm x 0.16 ± 0.02 cm, upholstered with leather. The back size is 48 W cm + 2 cm x 77 D cm + 2 cm . The armrest

top is molded from polyurethane and mounted on to a drop lift adjustable type tubular armrest support made of

Ø3.81±0.03cm x 0.2±0.01cm thick M.S. ERW tube having chrome plated finish. The armrest is height adjustable up to

6.5±0.5 cm in 5 steps. The adjustable tilting mechanism is designed with following features : 360° revolving type, front-

pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort, tilt tension adjustment

can be operated in seating position, 5position tilt limiter giving option of variable tilt angle to the chair, Seat/back tilt

35 MEETING CHAIR Each 20 44269.00 8,85,380.00

ratio 1:2, Seat depth adjustment is integrated in the seat through a sliding mechanism. Seat depth adjustment range is

of 6.0±0.5cm. It can be adjusted in the range of 7.42±0.5 comfort the comfortable back support to suit individual need.

The pneumatic height adjustment has an adjustment stroke of 10.0±0.3cm. The pedestal is high pressure die cast

polished aluminium & fitted with 5 nos. of twin wheel castors. The pedestal is 65.0±0.5cm pitch centre dia.

(75.0±1.0cm with castors). 5 nos. of twin wheel castors are injection moulded in plastic having 6.0±0.1cm wheel

diameter and assembled to pedestal. All complete as per direction and satisfaction of Engineer-in-charge.

Providing & Placing in position of High back leather upholstery chair as per Reference image /photograph or

equivqlent as approved . The cushioned seat and back shall be made of 1.2+/-0.1cm hot pressed plywood is

upholstered with leather and moulded high resilience polyurethane foam of density 45±2 kg/m³, & hardness load of

16±2 kgf as per IS:7888 for 25% compression. Seat Size is 47.0 W cm + 2cm W x 48.0 D cm + 2 cm . The back is

cushioned made of PU foam with insitu moulded M.S. ERW round tube of size 1.9 cm ± 0.03cm x 0.16 ± 0.02 cm,

upholstered with leather. The back size is 48 W cm + 2 cm x 77 D cm + 2 cm . The armrest top is molded from

polyurethane and mounted on to a drop lift adjustable type tubular armrest support made of Ø3.81±0.03cm x

0.2±0.01cm thick M.S. ERW tube having chrome plated finish. The armrest is height adjustable up to 6.5±0.5 cm in 5

steps. The adjustable tilting mechanism is designed with following features : 360° revolving type, front-pivot for tilt with

BOARD ROOM/ feet resting on ground and continuous lumbar support ensuring more comfort, tilt tension adjustment can be operated

CONFERENCE in seating position, 5position tilt limiter giving option of variable tilt angle to the chair, Seat/back tilt ratio 1:2, Seat

ROOM CHAIR depth adjustment is integrated in the seat through a sliding mechanism. Seat depth adjustment range is of 6.0±0.5cm.

PERSON It can be adjusted in the range of 7.42±0.5 comfort the comfortable back support to suit individual need. The

pneumatic height adjustment has an adjustment stroke of 10.0±0.3cm. The pedestal is high pressure die cast

polished aluminium & fitted with 5 nos. of twin wheel castors. The pedestal is 65.0±0.5cm pitch centre dia.

(75.0±1.0cm with castors). 5 nos. of twin wheel castors are injection moulded in plastic having 6.0±0.1cm wheel

diameter and assembled to pedestal. All complete as per direction and satisfaction of Engineer-in-charge.

Digitally signed by ANUJ

Providing & Placing in position of Medium back with leatheritte upholstery chair as per Reference image

/photograph or equivqlent as approved . The cushioned seat and back shall be made of 1.2+/-0.1cm hot pressed

plywood is upholstered with leather and moulded high resilience polyurethane foam of density 45±2 kg/m³, & hardness

load of 16±2 kgf as per IS:7888 for 25% compression. Seat Size is 47.0 W cm + 2cm W x 48.0 D cm + 2 cm . The

back is cushioned made of PU foam with insitu moulded M.S. ERW round tube of size 1.9 cm ± 0.03cm x 0.16 ± 0.02

cm, upholstered with leather. The back size is 48 W cm + 2 cm x 77 D cm + 2 cm . The armrest top is molded from

polyurethane and mounted on to a drop lift adjustable type tubular armrest support made of Ø3.81±0.03cm x

0.2±0.01cm thick M.S. ERW tube having chrome plated finish. The armrest is height adjustable up to 6.5±0.5 cm in 5

steps. The adjustable tilting mechanism is designed with following features : 360° revolving type, front-pivot for tilt with

BOARD ROOM/ feet resting on ground and continuous lumbar support ensuring more comfort, tilt tension adjustment can be operated

37 CONFERENCE in seating position, 5position tilt limiter giving option of variable tilt angle to the chair, Seat/back tilt ratio 1:2, Seat Each 96 59,997.00 57,59,712.00

ROOM CHAIR depth adjustment is integrated in the seat through a sliding mechanism. Seat depth adjustment range is of 6.0±0.5cm.

It can be adjusted in the range of 7.42±0.5 comfort the comfortable back support to suit individual need. The

pneumatic height adjustment has an adjustment stroke of 10.0±0.3cm. The pedestal is high pressure die cast

polished aluminium & fitted with 5 nos. of twin wheel castors. The pedestal is 65.0±0.5cm pitch centre dia.

(75.0±1.0cm with castors). 5 nos. of twin wheel castors are injection moulded in plastic having 6.0±0.1cm wheel

diameter and assembled to pedestal. All complete as per direction and satisfaction of Engineer-in-charge.

Café chair : Designed to hold straps & handbags, UNDERSTRUCTURE Powder Coated

UPHOLSTERY Bent Ply Mould Double

Side Re-Engineered Veneer. Well designed bushes to help correct

stackability and damping to shocks.

Providing and fixing in position of customised design & drawings ( factory made) Metal Storage Compactors of at

all floors to store box files, flat files, documents, etc in Push-Pull type unit with central locking system as per

drawings(variation if any with actual measurement at site will be taken). The movement of storage unit trolley is

achieved by “C” type handle of approved make with inbuilt security lock in drive wheels over rails which are installed

above floors by means of expansion type. Foundation bolts having in stoppers. The undercarriage is welded frame

made of HR sheet 3.15mm thick confirming to IS:10748 suitably fabricated to take the load based on configuration

and as per the manufacturer. Specifications: there are 4 adjustable shelves per body giving 5 loading levels and each

shelf designed to carry a UDL of 50kgs minimum. Optimizer height from floor is 2080mm (1980 body+65 under

39 carriage+35 channel system). The main body I/C shelves are made of 1mm thick CRCA steel conforming to IS:513 (L)915X(D) 915 X (H) 2080 Each 8 61,236.00 4,89,888.00

grade. The final finish consisting of epoxy polyester powder coat of approved colour and shade with a dry film

thickness of minimum 40 microns and anti-rust surface treatment as per the satisfaction of the engineer in-charge.

The complete compactor unit will be comprised of size(915x915x2080mm). the metal sheet to be used of tata sheet.

The locking arrangement of Key man or equivalent. The product should be from BIFMA/ ISO 9001-2008/ ISO 14001:

2004 certified company (photograph annexed is only for guidance). Complete as per direction and satisfaction of

engineer in-charge.

Digitally signed by ANUJ

BOQ FOR SOFT LANDSCAPE WORKS

S.No. Particulars Qty. unit Rate Amt. Particulars

1 Providing , laying and plantation at site i/c 800 each 1177.00 941600

watering and removal of unserveiceable

material’s well developed fresh & healthy

Trees /Plant as per direction of the officer-in-

Conocarpus trees 8'-10' ht

Conocarpus trees 8'-10' ht

2 Providing , laying and plantation at site i/c 1150 each 235.00 270250

watering and removal of unserveiceable

material’s well developed fresh & healthy

Trees /Plant in 30 cm Earthen Pot/Plastic Pot

and as per direction of the officer-in-charge .

Chandni variegated 2' ht

Chandni variegated 2' ht

3 Providing , laying and plantation at site i/c 550 each 249.00 136950

watering and removal of unserveiceable

material’s well developed fresh & healthy

Trees /Plant in 30 cm Earthen Pot/Plastic Pot

and as per direction of the officer-in-charge ..

Hamelia patens 3' ht

Hamelia patens 3' ht

4 Providing , laying and plantation at site i/c 650 each 249.00 161850

watering and removal of unserveiceable

material’s well developed fresh & healthy

Trees /Plant in 30 cm Earthen Pot/Plastic Pot

and as per direction of the officer-in-charge .

5 Providing , laying and plantation at site i/c 250 each 249.00 62250

watering and removal of unserveiceable

material’s well developed fresh & healthy

Trees /Plant in 30 cm Earthen Pot/Plastic Pot

and as per direction of the officer-in-charge . .

Calliandra brush 4' ht

Calliandra brush 4' ht

6 Providing , laying and plantation at site i/c 2500 each 21.00 52500

watering and removal of unserveiceable

material’s well developed fresh & healthy

Trees /Plant in 30 cm Earthen Pot/Plastic Pot

and as per direction of the officer-in-charge .

Wedelia trilobata ground cover

Wedelia trilobata ground cover

Digitally signed by ANUJ

7 Providing , laying and plantation at site i/c 200 each 277.00 55400

watering and removal of unserveiceable

material’s well developed fresh & healthy

Trees /Plant in 30 cm Earthen Pot/Plastic Pot

and as per direction of the officer-in-charge .

Putranjiva 3' ht

Putranjiva 3' ht

8 Providing , laying and plantation at site i/c 300 each 277.00 83100

watering and removal of unserveiceable

material’s well developed fresh & healthy

Trees /Plant in 30 cm Earthen Pot/Plastic Pot

and as per direction of the officer-in-charge .

Chandni single 3.5' ht

Chandni single 3.5' ht

9 Providing , laying and plantation at site i/c 600 each 83.00 49800

watering and removal of unserveiceable

material’s well developed fresh & healthy

Trees /Plant in 30 cm Earthen Pot/Plastic Pot

and as per direction of the officer-in-charge .

Jade plant ground cover

Jade plant ground cover

10 Providing , laying and plantation at site i/c 30 each 4845.00 145350

watering and removal of unserveiceable

material’s well developed fresh & healthy

Trees /Plant in 30 cm Earthen Pot/Plastic Pot

and as per direction of the officer-in-charge .

Ficus retusa topiary 6' -7' ht

Ficus retusa topiary 6' -7' ht

11 Providing , laying and plantation at site i/c 20 each 3461.00 69220

watering and removal of unserveiceable

material’s well developed fresh & healthy

Trees /Plant in 30 cm Earthen Pot/Plastic Pot

and as per direction of the officer-in-charge .

Terminalia mantaly 10' -12'

Terminalia mantaly 10' -12'

12 Providing , laying and plantation at site i/c 5000 each 21.00 105000

watering and removal of unserveiceable

material’s well developed fresh & healthy

Trees /Plant in 30 cm Earthen Pot/Plastic Pot

and as per direction of the officer-in-charge .

Red Irisine ground cover

Red Irisine ground cover

Digitally signed by ANUJ

13 Providing , laying and plantation at site i/c 100 each 166.00 16600

watering and removal of unserveiceable

material’s well developed fresh & healthy

Trees /Plant in 30 cm Earthen Pot/Plastic Pot

and as per direction of the officer-in-charge .

Oleander desi 3' ht

Oleander desi 3' ht

14 Providing and Displaying as per direction 4100 sqft sqft 118.00 263500

of the officer-in-charge .

Artificial grass

Artificial grass

15 Providing and Displaying as per direction 80 each 415.00 33200 Cattle manure (bag)

of the officer-in-charge . Cattle manure (bag)

Notes : all above rates are inclusive of

Ecxcavation, filling of good earth of pits for

respective plants , Supplying and stacking of

good earth at site including royalty all lead

complete (earth measured in stacks will be

reduced by 20% for payment).

Supplying ,stacking ,mixing,spreading sludge/

well decayed cattle manure inclusive required

fretilisers etc at site including royalty complete

job all lead (sludge measured in stacks will be

reduced by 8% for payment).

Complete maintenance ( 2 years ) of the entire

garden features having as per yard stick in the

garden area i.e. lawn, trees, shrubs, edge,

flower beds, foliages,creepers etc. including

hoeing,weeding pruning replacement of plants,

gap filling, watering, mowing of lawn, grass

cutting by lawn mover and brush cutter,

removal of garden waste, applying insecticide,

pesticide &fertilizers(whenever required) top

dressing of lawn with good earth and menure

and maintenance of other garden related works

as directed by office-in-charge .

Payment terms : 70% of the rates shall be paid

after plantation and 30% shall be paid 2 years

maintence period.

Digitally signed by ANUJ

PROJECT: GRID INDIA

PACKAGE :- PLUMBING WORKS

S.NO DESCRIPTION Total Amount

S.NO DESCRIPTION Total Amount

DSR 2023 Amount NS Amount

1 SANITARY FIXTURE 1,81,690 29,64,378

3 INTERNAL WATER SUPPLY 7,18,185 5,84,621

Cost Index on DSR 2022 @3% (on base of PAR 2023) per CPWD OM DG/Cost

5 GRAND TOTAL DSR + NSR 69,32,336.14

5 GRAND TOTAL DSR + NSR 69,32,336.14

Digitally signed by ANUJ

PROJECT: GRID INDIA

PACKAGE :- PLUMBING

REF DSR-2023/ NON DSR REFERENCE

DSR Rate Total Amount

DSR Rate Total Amount

S.No. Description Qty. Unit Rate (Rs.) @0.973

SANITARY FIXTURE DSR

Providing, fixing, testing and commissioning of white vitreous China

wall mounting Wall mounted W.C with concealed cistern European

water closet with C.P. bolts, nuts, C.I. chair (painted with two coats of

enamel paint over a coat of primer) or other hanging arrangements,

bakelite / poly propylene seat & cover with C.P. hinges & rubber buffers,

C.P. brass screw, washer with all accessories. Including cutting & making

good the walls, floors, slab wherever required .

Providing and fixing Health Faucet ABS with double lock 1.0 m long 8mm

2 dia and SS flexible hose and wall hook including CP flange. 15mm dia. 54 No. 1443 77,922 MR -2

Providing and Fixing 2 Nos. support arms and backrest to mounted on the

3 track (vertically and laterally) for handicap toilet complete as required. 4 No. 1720 6,880 MR -3

Providing, fixing, testing & commissioning of C.P. brass Sensor tap.

Supply, installation , testing & commissioning first quality white vitreous

china half padestal washbasins, 32 mm CP brass waste ( full threaded)

and CP brass cast bottle trap and pipe to wall with CP brass flange and

rubber adopter for waste connection complete including filling gap

between counter and wash basin with approved type poly sulphide

sealant, cutting and making good the walls wherever required as per

manufacturer recommendation. ( for handicapt toilet)

Providing and fixing stainless steel A ISI 304 (18/8) Kitchen sink as per

IS : 13983 with CI bracket and stainless steel plug 40 mm including

painting of fittings and brackets ,cutting and making good the walls

wherever required:

Kitchen sink with drain board - 17.10.1

Digitally signed by ANUJ

REF DSR-2023/ NON DSR REFERENCE

DSR Rate Total Amount

DSR Rate Total Amount

S.No. Description Qty. Unit Rate (Rs.) @0.973

Providing and fixing CP Brass Single lever telephonic wall mixer of quality

8 & make as approved by Engineer in charge. (a) 15 mm nominal dia 3 No. 6940.75 6753.3498 20,260 17.22B (DSR- 2023)

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality

& make and as per the direction of Engineer-in-charge.

Providing and fixing uplasticized connection pipe with brass union:

Providing and fixing CP BRASS towel ring complete with brackets fixed

12 to wooden cleats with CP brass screws with concealed fittings 56 No. 1227 - 68,712 MR - 6

arrangement of approved quality and colour

Providing and fixing CP Brass soap Dish Holder.

Providing and fixing C.P. brass angle valve for basin mixer and geyser

points of approved quality conforming to IS:8931

15 Providing and fixing toilet paper holder : 0 - 17.34 (DSR- 2023)

Fixing of horizontal/vertical storage type water heater of approved shade

with copper container with multi-function safety valve for high pressure

operation without additional pressure reducing valve, glass wool

16 insulation, stove enamelled M.S jacket, thermostatically controlled inner - MR - 8

heater with pilot neon lamps, angle valve on inlet connection, 15mm dia

C.P flexible connection pipe in inlet & outlet suitable for working pressure

of 5 kg/sqcm complete as required.

16.1 Capacity: 6 litres 3 No. 10311 - 30,933

Digitally signed by ANUJ

REF DSR-2023/ NON DSR REFERENCE

DSR Rate Total Amount

DSR Rate Total Amount

S.No. Description Qty. Unit Rate (Rs.) @0.973

Providing and fixing white vitreous china battery based infrared sensor

operated urinal of approx. size 610 x 390 x 370 mm having pre & post

flushing with water (250 ml & 500 ml consumption), having water inlet

from back side, including fixing to wall with suitable brackets all as per

manufacturers specification and direction of Engineer-in-charge.

Providing and fixing solid state, no touch operting, fully hygienic hand

drier of approved shade with single blower, with time delay, summer &

18 winter control, music while drying, volume ON/OFF controls including 8 No. 11711 - 93,688 MR - 10

providing necessary brackets, cable from drier to Plug, Plug top key and

lock etc, complete as required.

19 Providing and fixing Coat Hook. 54 No. 686 - 37,027 MR - 11

20 Providing and fixing soil, waste and vent pipes :

Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989.

Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989.

Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989.

Providing and fixing on wall face uplasticised Rigid PVC rain water pipes

conforming to IS 13592 Type A including jointing with steel ring

conforming to IS 5382 leaving 10 mm gap for thermal expansion (i) single

socketed pipes and fitting as required.

Providing and fixing to the inlet mouth of rain water pipe cast iron grating

15 cm diameter and weighing not less than 440 grams.

Digitally signed by ANUJ

REF DSR-2023/ NON DSR REFERENCE

DSR Rate Total Amount

DSR Rate Total Amount

S.No. Description Qty. Unit Rate (Rs.) @0.973

Providing and fixing M.S. stays and clamps for sand cast iron/

centrifugally cast (spun) iron pipes of diameter :

Providing and fixing bend of required degree with access door, insertion

rubber washer 3 mm thick, bolts and nuts complete.

25 Providing and fixing plain bend of required degree. 0.0 - -

25.1 Sand cast iron S&S as per IS : 3989 150 No. 570.05 554.7 83,199

25.3 Sand cast iron S&S as per IS - 3989 35 No. 629 - 22,005 MR - 16

Providing and fixing single equal plain junction of required degree with

26 access door, insertion rubber washer 3 mm thick, bolts and nuts - - MR - 17

26.1 Sand cast iron S&S as per IS - 3989 50 No. 1244 - 62,202 A

26.2 Sand cast iron S&S as per IS - 3989 25 No. 164 - 4,090 B

27 Providing and fixing single equal plain junction of required degree : - -

28.0 Providing and fixing single unequal plain junction of required degree : 0.0 - -

29.00 Providing and fixing terminal guard: 0.0 - -

Digitally signed by ANUJ

REF DSR-2023/ NON DSR REFERENCE

DSR Rate Total Amount

DSR Rate Total Amount

S.No. Description Qty. Unit Rate (Rs.) @0.973

Providing & fixing of drip sealant for the cast iron pipe jointing as per

30.1 75mm diameter 50 No. 15 - 750 A

Providing and fixing trap of self cleansing design with screwed down or

31 hinged grating with or without vent arm complete, including cost of cutting - -

and making good the walls and floors :

100 mm inlet and 100 mm outlet - -

Providing and fixing G.I. Pipes ( Confirming IS 1239 class - B)complete

with G.I. fittings and clamps, i/c making good the walls etc. concealed

pipe, including painting with anti corrosive bitumastic paint, cutting

chases and making good the wall :

32.1 32 mm dia. nominal bore 100 Metre 837 - 83,323 A

32.1 40 mm dia. nominal bore 22 Metre 1002 - 22,044 B

32.2 50 mm dia. nominal bore 26 Metre 1279 - 33,766 C

Providing and fixing G.I. inlet hopper with two or three inlets fittings to

receive waste pipes from fixtures waste. The hopper shall be fabricated

from 100 mm dia upto 800 mm long G.I. heavy class pipe and welded G.I.

sockets, fixed to C.I. trap with drip seal joint and support through

galvanized steel support from slab or set in cement concrete mix 1:2:4

complete as required. The hopper shall be hot dip galvanized after

fabrication and fixed to CI trap / pipe with drip seal joint.

Providing & fixing G.I. waste with reducing elbow & nipple cutting chases,

34 the floor / slab, repairs complete as required and connection to GI / CI - - MR - 21

Providing & fixing 100 mm diameter Cast Iron Clean out plug for soil,

waste pipes conforming to IS 3989.

INTERNAL WATER SUPPLY

Digitally signed by ANUJ

REF DSR-2023/ NON DSR REFERENCE

DSR Rate Total Amount

DSR Rate Total Amount

S.No. Description Qty. Unit Rate (Rs.) @0.973

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c

36 cutting and making good the walls etc. - - DSR -2023 -18.10

Internal work - Exposed on wall and terrace

36.1 20 mm dia nominal bore 6 Metre 437.6 425.8 2,342 DSR -2023 -18.10.2

36.2 25mm dia nominal bore 39 Metre 552 536.8 20,667 DSR -2023 -18.10.3

36.3 32mm dia nominal bore 121 Metre 667 649.0 78,528 DSR -2023 -18.10.4

36.4 40 mm dia nominal bore 64 Metre 811 789.1 50,345 DSR -2023 -18.10.5

36.6 65 mm dia nominal bore 56 Metre 1021 - 57,278 MR -23

Domestic and Flushing water supply-Providing and fixing Chlorinated

Polyvinyl Chloride (CPVC - SDR 11) pipes, having thermal stability for hot

& cold water supply, including all CPVC plain & brass threaded fittings,

37 including fixing the pipe with clamps at 1.00 m spacing. This includes - - DSR -2023-18.8

jointing of pipes & fittings with one step CPVC solvent cement and testing

of joints complete as per direction of Engineer in Charge.

(Concealed Work) - -

37.1 15 mm dia nominal bore 83 Metre 498 484.4 39,960 DSR -2023 -18.8.1

37.4 32 mm dia nominal bore 63 Metre 739 719.3 45,103 DSR -2023 -18.8.4

37.5 40 mm dia nominal bore 25 Metre 1055 - 26,692 MR -24

Providing and fixing nitrile rubber insulation and proprietary polyshield

outer mechanical protection ON nitrile rubber insulation comprising of

wrapping with poly glass tape helically wound and subsequently applying

2 coats of polyshield material (resin & hardener) as per manufacturers

specification and approved by Project Manager / Consultants.

38.1 20 mm dia. nominal bore 10 Metre 210 - 2,079 A

Providing & fixing full way lever operated Brass ball valve of brass body

with stainless steel ball conforming to IS 778 with threaded / flanged joints

(PN 16) complete with nuts, bolts, gaskets, washers and fixing to

supports etc.(PN 16)

39.1 20 mm nominal bore 18 No. 673 - 12,114 A

39.2 25 mm nominal bore 7 No. 775 - 5,425 B

39.3 32 mm nominal bore. 5 No. 1324 - 6,620 C

39.4 40 mm nominal bore 5 No. 1857 - 9,285 D

39.5 50 mm nominal bore 1 No. 2711 - 2,711 E

Digitally signed by ANUJ

REF DSR-2023/ NON DSR REFERENCE

DSR Rate Total Amount

DSR Rate Total Amount

S.No. Description Qty. Unit Rate (Rs.) @0.973

Supply, Installation, Testing and Commissioning of compact packaged type skid

mounted, self contained variable frequency drive hydropneumatic system

complete as per following technical specification complete as required:-

(i) In- line vertical multistage centrifugal clear water pump set with SS-304

casing, SS-304 impeller with SS-316 shaft ,CI base with CED coating complete

directly coupled with TEFC induction motor of class "F" insulation & efficiency - -

class IE-2, 2900rpm, suitable for opertion on 415 Volts ±10%, 3 phase, 50 Hz

A.C. supply complete.

(ii) The entire system shall be mounted on a common base frame i/c common

suction and common delivery of G.I heavy class pipe headers with flanges,

interconnecting piping with all required Conrol Valves, Non-return valves,

pressure guage with isolation cock etc. and all requried accessories.

(iii) Pressure vessel of non corrosive FRP composite construction lined with

NSF and/or FDA listed material, like high density polyethylene with fully

replaceable polyurethane. Air cell burst pressure of minimum of 3 times the

vessel operating pressure and prototype cycle tested for 80,000 cycles with - -

charging connections to dischage pipe line with necessary flanges, gaskets,

isolating valve, nuts/ bolts etc. with suitable foundation boits & other

accessories, complete.

(iv) Panel mounted microprocessor multi pump contoller with large graphical

display and Flying variable frequency drive (VFD) mounted inside a panel

complete with pressure sensor transmitter. The graphical display capable to

show number of pumps running & also communicate with other controllers

following with open protocol through RS485 port. System should be capable to - -

compensate for frictional losses at lower flows. All alarms should be displayed in

the controller. The panel should also have provision for manual / automatic

alternate (cyclic) operation of pumps, ON/OFF switch, complete.

(v) Necessary foundationing bolts, vibration elimination pads and other

accessories complete as required.

Duty of each pump suitable for:- - -

No. of Pumps : 2nos. (1 W + 1 S) - -

Capacity : 0.5LPS - -

Head : 30 Meters - -

40.1 Air Vessel : 1 Nos of Min. 60 Liters Cap. 1 Set 462417 - 4,62,417 MR -27

Digitally signed by ANUJ

SUMMARY (Electrical Works)

SCHEDULE OF QUANTITIES, ELECTRICAL WORKS

GRID INDIA, AYURVIGYAN NAGAR, NEW DELHI

Sl. No. SUB HEADS DSR 2022 AMOUNT Non DSR AMOUNT

A HT CABLE & TERMINATION 2,29,328.29 5,06,272.00

B HT PANEL & CSS WORKS 0.00 1,28,58,122.00

C LT PANELS & DISTRIBUTION BOARDS 8,87,238.79 1,07,21,885.00

D MV CABLES, CABLE JOINTING & END TERMINATIONS 40,728.64 1,10,27,189.00

E CABLE TRAYS WORKS 11,41,543.70 1,80,600.00

G CIRCUIT CUM POINT WIRING (With MS CONDUITING) 0.00 62,40,212.00

H CONDUITING & RACEWAYS FOR VOICE/ DATA (N/W) & TV SYSTEM 9,17,601.32 18,89,812.91

I EARTHING SYSTEM 35,00,182.61 3,13,490.00

K INTERNAL LIGHT FIXTURES AND FANS 0.00 1,11,44,530.00

L LIGHTING MANEGMENT SYSTEM 0.00 49,74,197.00

M BUS DUCTS - COMPACT SANDWITCH TYPE 0.00 1,64,51,840.00

N FIRE DETECTION AND ALARM SYSTEM - ANALOG ADDRESSABLE SYSTEM 62,46,921.36 15,17,858.00

O CLEAN AGENT BASED FIRE SUPPRESSION SYSTEM 0.00 54,80,338.00

P VERY EARLY SMOKE DETECTION & ALARM SYSTEM 0.00 5,86,246.00

R EV CHARGER 0.00 26,84,388.00

S PARKING MANAGEMENT 0.00 1,64,800.00

Less Cost Index on DSR 2022 @2.73% (On base of PAR 2021) as per CPWD

OM DG/Cost Index/06 dated 13.05.2022 (110 to 107) -3,53,960.77

Cost Index on DSR 2022 @3% (on base of PAR 2023) per CPWD OM

DG/Cost Index/10 dated 11.09.2024 1,29,89,984.09

GRAND TOTAL 12,42,56,918.00

GRAND TOTAL 12,42,56,918.00

Digitally signed by ANUJ

SCHEDULE OF QUANTITIES, ELECTRICAL WORKS

GRID INDIA, AYURVIGYAN NAGAR, NEW DELHI

SL. NO. ITEM DESCRIPTIONS UNIT QTY. DSR RATE Non DSR RATE DSR AMOUNT Non DSR Ref. DSR

@1.0633 (Rs.) (Rs.) AMOUNT 2022/ MR

A HT CABLE & TERMINATION

1.1 Supply of following size of 11kV (Un earthed) grade, multicore stranded

aluminium conductor, XLPE insulated & PVC sheathed armoured power

cable conforming to IS: 7098 (Part-II) 2011 with upto date ammendments

complete as required and as per specification encolsed.

2 HT CABLES END TERMINATION

supplying and making indoor cable end termination with heat shrinkable

jointing kit complete with all accessories including lugs suitable for following

size of 3 core, XLPE aluminium conductor cable of 11 kV grade as required.

Supplying and making outdoor cable end termination with heat shrinkable

jointing kit complete with all accessories including lugs suitable for following

size of 3 core, XLPE aluminium conductor cable of 11 kV grade as required

3 HT CABLES LAYING

3.1 Laying of one number XLPE power cable of 11kV grade of following size

direct in ground including excavation, sand cushioning, protective covering

and refilling the trench etc as required. 8.1

3.2 Laying of one number additional XLPE power cable of 11kV grade of

following size direct in ground in the same trench in one tier horizontal

formation including excavation, sand cushioning, protective covering and

refilling the trench etc as required. 8.2

3.3 Laying of one number XLPE power cable of 11kV grade of following size in

the existing RCC/ HUME/ METAL pipe as required. 8.3

3.4 HDPE PIPES

3.4.1 Supplying and laying of following size DWC HDPE pipe ISI marked along

with all accessories like socket, bend, couplersetc. conforming to IS: 14930,

Part II complete with fitting and cutting, jointing etc. direct in ground (75 cm

below ground level) including excavation and refilling the trench but

excluding sand cushioning and protective covering etc., complete as

required. 14.16

4 Constructing water tight brick masonry manhole with 75 class designation

bricks in cement mortar 1:4 (1 cement: 4 coarse sand), R.C.C. top slab with

1:2:4 mix (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm

nominal size). Foundation concrete 150 mm thick 1:4:8 mix (1 cement: 4

coarse sand: 8 graded stone aggregate 40 mm nominal size), inside and

outside plastering 12 mm thick with cement plaster 1:3 (1 cement: 3 coarse

sand) finished with a floating coat of neat cement and making channels and

benching in cement concrete 1:2:4 mix (1 cement: 2 coarse sand: 4 graded

stone aggregate 20 mm nominal size) finished with a floating coat of neat

cement complete as per standard design, complete with DI cover Heavy

duty of adequate size as per standard design and approved drawings. (Price

shall include the, cost of excavation, back filling, disposal of surplus earth,

dewatering & water proofing of manholes as directed at site & other

associated civil works).

4.1 Inside size 1000mm x 1000mm x 1100mm deep. Nos. 8 1,394 0.00 11152.00 EL. MR-2

Total Carried to Summary 2,29,328.29 5,06,272.00

Digitally signed by ANUJ

SL. NO. ITEM DESCRIPTIONS UNIT QTY. DSR RATE Non DSR RATE DSR AMOUNT Non DSR Ref. DSR

@1.0633 (Rs.) (Rs.) AMOUNT 2022/ MR

B HT PANEL & CSS WORKS

1.0 11kV HT PANEL BOARD (ONE BREAKER)

(Earlier 1 No. Incomers + 4 Nos. Out goings HT Panel will convert to

Two Incomer + 1 No. Bus Coupler + 3 Nos. Outgoing after adding 1 No.

New VCB Breaker.) - -

Design, manufacture, supply, installation, testing and commissioning of 800

Amps., 11kV, 18.4kA breaking capacity (350 MVA) VCB panel board

fabricated out of 2mm sheet steel, dust tight, vermin proof, totally enclosed

and fully interlocked, IP-4X protection, cubical type, floor mounting,

extensible on both sides, suitable for indoor operation at 11kV, 3 phase, 50

Hz, AC supply complete with rack in - rack out mechanisms, switches, plugs

& sockets and all required accessories, cable termation box at back with

TOP cable entry for cable size upto 3 core 400 sqmm. armoured cable for

each section, internal copper wiring, earth terminals, painting etc. as

required, as per specifications & SLD with the following equipped switch

gears and accessories complete in aal respect.

a) INCOMER - 1 NO. - -

Each feeder shall consist of : - -

i) 800 Amps., 11kV horizontal draw out type VCB with motorized spring